Samsung PG19N, PG17N Service Manual

Download

Manual

SERVICE

COLOR MONITOR CONTENTS

1. Precautions

2. Product Specifications

3. Disassembly & Reassembly

4. Alignment & Adjustments

5. Troubleshooting

6. Exploded View & Parts List

7. Electrical Parts List

8. Block Diagram

9. Wiring Diagram

10. Schematic Diagrams

COLOR MONITOR

PG17N*/PG19N*

Samsung Electronics Co., Ltd. April 2000. Printed in Korea P/N : BH68-00129F-01

WARNINGS

1. For continued safety, do not attempt to modify the circuit board.

2. Disconnect the AC power before servicing.

3. When the chassis is operating, semiconductor heatsinks are potential shock hazards.

1-1-1 Servicing the High Voltage VR

and CRT :

WARNING:A high voltage VR replaced in the wrong

direction may cause excessive X-ray emissions.

Caution: When replacing the high voltage

adjustment VR, it must be fixed by a soldering iron after it is properly set.

1. When servicing the high voltage system, remove the static charge by connecting a 10 kohm resistor in series with an insulated wire (such as a test probe) between the chassis and the anode lead.

2. If the HV VR requires adjustment, (a) Replace the VR and adjust the high voltage to the specification. (b) Use a soldering iron to melt the adjustment cap on the HV VR to prevent any movement.

3. When troubleshooting a monitor with excessively HV, avoid being unnecessarily close to the monitor. Do not operate the monitor for longer than is necessary to locate the cause of excessive voltage.

4. High voltage should always be kept at the rated value, no higher. Only when high voltage is excessive are X-rays capable of penetrating the shell of the CRT, including the lead in glass material. Operation at high voltages may also cause failure of the CRT or high voltage circuitry.

5. When the HV regulator is operating properly, there is no possibility of an X-ray problem. Make sure the HV does not exceed its specified value and that it is regulating correctly.

6. The CRT is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the CRT only with one that is the same or equivalent type as the original.

7. Handle the CRT only when wearing shatterproof goggles and after completely discharging the high voltage anode.

8. Do not lift the CRT by the neck.

1-1-2 Fire and Shock Hazard :

Before returning the monitor to the user, perform the following safety checks:

1. Inspect each lead dress to make certain that the leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the monitor.

2. Inspect all protective devices such as nonmetallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacitor networks, mechanical insulators, etc.

3. Leakage Current Hot Check (Figure 1-1):

WARNING: Do not use an isolation transformer during

this test.

Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI C101.1, Leakage Current for

Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7).

4. With the unit completely reassembled, plug the AC line cord directly into a 120V AC outlet. With the unit’s AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the power-plug prongs in the AC outlet and repeat the test.

Figure 1-1. Leakage Current Test Circuit

1-1-4 Product Safety Notices

Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection. The protection they give may not be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by

on schematics and parts lists. A substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire and / or other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate.

Components identified by on schematics and parts lists must be sealed by a soldering iron after replacement and adjustment.

PG17N*/PG19N* 1-1

1 Precautions

1-1 Safety Precautions

DEVICE UNDER TEST

TEST ALL

EXPOSED METAL

SURFACES

(READING SHOULD

NOT BE ABOVE 0.5mA)

LEAKAGE CURRENT

TESTER

2-WIRE CORD

ALSO TEST WITH

PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)

EARTH

GROUND

1. Servicing precautions are printed on the cabinet, and should be followed closely.

2. Always unplug the unit’s AC power cord from the AC power source before attempting to: (a) remove or reinstall any component or assembly, (b) disconnect PCB plugs or connectors, (c) connect all test components in parallel with an electrolytic capacitor.

3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position.

4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the area around the serviced part has not been damaged.

1. Immediately before handling any semiconductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wriststrap device. To avoid a shock hazard, be sure to remove the wrist strap before applying power to the monitor.

2. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of an electrostatic charge.

3. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESDs.

4. Use only a grounded-tip soldering iron to solder or desolder ESDs.

5. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static” can generate electrical charges sufficient to damage ESDs.

5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks).

6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500 V) to the blades of the AC plug.

The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm.

7. Never defeat any of the +B voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed.

8. Always connect a test instrument’s ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument’s ground lead last.

6. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials.

7. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed.

Caution: Be sure no power is applied to the

chassis or circuit and observe all other safety precautions.

8. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting your foot from a carpeted floor can generate enough static electricity to damage an ESD.

9. Indicates ESDs on the Schematic Diagram in this manual.

1 Precautions

1-2 PG17N*/PG19N*

1-3 Electrostatically Sensitive Devices (ESD) Precautions

Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some fieldeffect transistors. The following techniques will reduce the incidence of component damage caused by static electricity.

1-2 Servicing Precautions

WARNING1: First read the “Safety Precautions” section of this manual. If unforeseen circumstances

create conflict between the servicing precautions and safety precautions, always follow the safety precautions.

WARNING2: A high voltage VR replaced in the wrong direction may cause excessive X-ray

emissions.

WARNING3: An electrolytic capacitor installed with the wrong polarity might explode.

2 Product Specifications

2-1 Specifications

Picture Tube: 17-Inch (43 cm): 16-inch (40.6 cm) viewable, 19-Inch (48.2 cm): 18-inch (45.8 cm) viewable,

17”/19”: 0.25 mm Dot pitch, Full-square flat-face tube, 90˚ Deflection, Anti-Reflection coating with Anti-electrastatic, Medium short persistence phosphor

Scanning Frequency Horizontal : PG17N*: 30 kHz to 96 kHz (Automatic), PG19N*: 30 kHz to 110 kHz (Automatic) (Automatic) Vertical : 50 Hz to 160 Hz (Automatic)

Display Colors Unlimited colors

Maximum Resolution Horizontal : 1600 Dots

Vertical : 1200 Lines

Input Video Signal Analog, 0.7 Vp-p positive at 75 Ω, internally terminated

Input Sync Signal Separate Sync : TTL level positive/negative

Composite Sync : TTL level positive/negative Sync-on-Green : Composite sync 0.3 Vp-p negative (Video on Vp-p positive)

Maximum Pixel Clock rate 17” : 205 MHz, 19” : 240 MHz

Active Display 17” ; Horizontal : 312 mm ± 3 mm (12.28” ± 0.12”)

Vertical : 234 mm ± 3 mm (9.21” ± 0.12”)

19” ; Horizontal : 352 mm ± 3 mm (13.86” ± 0.12”)

Vertical : 264 mm ± 3 mm (10.39” ± 0.12”)

Input Voltage AC 90 to 264 Volts, 60/ 50 Hz ± 3 Hz

Power Consumption (max) 17”: 130 Watt , 19”: 150 Watt

Dimensions Unit ; 17” : 16.3 x 17.2 x 17.6 Inches (415.0 x 438 x 448 mm)

(W x D x H) 19” : 18.4 x 18.0 x 19.4 Inches (468 x 458 x 493 mm)

Carton ; 17” : 22.2 x 22.9 x 21.6 Inches (564 x 581 x 548 mm)

19” : 22.5 x 24.4 x 22.6 Inches (571 x 620 x 574 mm)

Weight (Net/Gross) 17” : 43.4 lbs (19.7 kg) / 50.7 lbs (23.0 kg) (Net/Gross) 19” : 55.8 lbs (25.3 kg) / 64.6 lbs (29.3 kg)

Environmental Considerations Operating Temperature : 32°F to 104°F (0°C to 40°C)

Humidity : 10 % to 80 % Storage Temperature : -4°F to 113°F (-20°C to 45°C) Humidity : 5 % to 95 %

• PG17N*/PG19N* complies with TCO 99 recommendations for reduced electromagnetic fields.

• Designs and specifications are subject to change without prior notice.

PG17N*/PG19N* 2-1

Item Description

2 Product Specifications

2-2 PG17N*/PG19N*

QRS

Video

Sync

Horizontal

Vertical

CDE

Video

Sync

Separate Sync

A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width

C : Back porch D : Active time Q : Back porch R : Active time

E : Front porch S : Front porch

Green

Vertical

Horizontal

Sync-on-Green

1024/75 Hz

1024 x 768

1600/85 Hz

1600 x 1200

800/85 Hz

800 x 600

VGA3/60Hz

640 x 480

VGA2/70Hz

720 x 400

Table 2-1. Timing Chart

fH (kHz)

A µsec

B µsec

C µsec

D µsec

E µsec

fV (Hz)

O msec

P msec

Q msec

R msec

S msec

Clock Freq. (MHz)

Polarity H.Sync

V.Sync

Remark

31.469

31.778

3.813

1.907

25.422

0.636

70.087

14.268

0.064

1.080

12.711

0.413

28.322

Negative

Positive

Separate

31.469

31.778

3.813

1.907

25.422

0.636

59.940

16.683

0.064

1.048

15.253

0.318

25.175

Negative

Separate

53.674

18.631

1.138

2.702

14.222

0.569

85.061

11.756

0.056

0.503

11.179

0.019

56.250

Positive

Separate

60.023

16.660

1.219

2.235

13.003

0.023

75.029

13.328

0.050

0.466

12.795

0.017

78.750

Positive

Separate

106.250

9.412

0.837

1.325

6.972

0.279

85.000

11.765

0.028

0.433

11.294

0.009

229.50

Positive

Separate

Mode

IBM VESA MAC.

Timing

68.677

14.561

1.016

2.201

10.836

0.508

84.997

11.765

0.044

0.524

11.183

0.015

94.500

Positive

Separate

68.681

14.560

1.280

1.440

11.520

0.320

75.062

13.322

0.044

0.568

12.667

0.044

100.000

Negative

SOG

49.726

20.110

1.117

3.910

14.524

0.559

74.551

13.414

0.060

0.784

12.549

0.020

57.284

Negative

SOG

91.146

10.971

1.016

1.422

8.127

0.406

85.024

11.761

0.033

0.483

11.235

0.011

157.500

Positive

Separate

79.976

12.504

1.067

1.837

9.481

0.119

75.025

13.329

0.038

0.475

12.804

0.013

135.000

Positive

Separate

1024/85 Hz

1024 x 768

1152/75 Hz

1152 x 870

832/75 Hz

832 x 624

1280/75 Hz

1280 x 1024

1280/85 Hz

1280 x 1024

3-1-1 Before making Disassembly

1. Disconnector signal cable and power cord from the monitor.

2. With a pad beneath it, stand the monitor on its front with the screen facing downward and the base close to you.

3. Make sure nothing will damage the screen.

3-1-2 Cabinet Disassembly

1. With a pad beneath it, stand the monitor on its front with the screen facing downward and the base closest to you. Make sure nothing will damage the screen.

2. Remove the Stand from the monitor. (Refer to Stand manual)

3. Incline the monitor by lifting the rear of the monitor.

4. Push the Opening jig each groove along the top of the monitor till it makes a “ttak” sound. (2 grooves : Left and Right, Make sure each snap is disengaged.)

5. Squeeze the hold-snap on bottom of the monitor using your hand.

6. Insert the Opening jig into the groove then release the hold-snap.

PG17N*/PG19N* 3-1

3 Disassembly and Reassembly

This section of the service manual describes the disassembly and reassembly procedures for the PG17N*/PG19N* monitors.

WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling

these components.

3-1 Disassembly

Cautions:1. Disconnect the monitor from the power source before disassembly.

2. Follow these directions carefully; never use metal instruments to pry apart the cabinet.

Figure 3

Figure 4

Figure 2

Figure 1

7. When the hold-snap release, lift the Rear Cover slightly to make sure it doesn’t reengage while you release the snap on the other side.

8. In a similar manner, Release the hold-snap on the opposite side.

9. Pull the Rear Cover up off the monitor.

3-1-3 Removing the Stand

Pull the tab outward on the chassis bottom and pull the tilt and swivel base up to remove it.

3-1-4 Removing the Top Shield

Remove the 6 screws on the top shield cover and remove the shield.

3-1-5 Removing the Video PCB Assembly and

the Video PCB

1. Disconnect CN102, CN101, CN12, CN-EMC and CNRed, white wires of SK105 on the Video PCB Assembly.

2. Remove the 2 wires video PCB Assembly rear shield and Video Assembly from the CRT neck.

3. Remove the 3 screws on the PCB Assembly.

4. Remove the Video PCB Assembly rear shield. (5 point)

5. Lift out the Video PCB and pleat it on a flat, level surface that is protected from static electricity.

3-1-6 Removing the Purity PCB Assembly

and Purity PCB

1. Remove the 1 screw on the PCB Assembly.

2. Disconnect CN801, CN803, CN804, CN805 on the Purity PCB Assembly and Purity PCB Assembly from the Main PCB Assembly.

3. Remove the 2 screws on the PCB Assembly.

3-1-7 Removing the Main PCB Assembly

and the Main PCB

1. Remove chassis ground wire on the lift side..

2. Disconnect CN201, CN409, CN601, H_DY, CN601 and anode cap on the Main PCB Assembly.

3. Squeeze the hold-snap on bottom of the monitor using your hand.

4. Remove right side shaft-power Main PCB.

5. Remove 6 screws on the main PCB.

6. Pull the Main PCB towards you and carefully lift out the main PCB and placet it on a flat, level surface that is protected from static electricity.

3-1-8 Removing the Bracket

Remove the 4 screws on the Front Cabinet.

3 Disassembly and Reassembly

3-2 PG17N*/PG19N*

3-2 Reassembly

Reassembly procedures are in the reverse order of Disassembly procedures.

Figure 6

Figure 5

3-1-9 Removing the Degaussing Coil

1. Using pinch-nosed pliers or long-nosed pliers, carefully push the 4 plastic ties on the Bracket.

2. Lift the Degaussing Coil Assembly from the Bracket.

3 Disassembly and Reassembly

PG17N*/PG19N* 3-3

4-2 Reassembly

Reassembly procedures are in the reverse order of Disassembly procedures.

4-1-1 Before Making Adjustments

4-1-1 (a) ORIENTATION

When servicing, always face the monitor to the east.

4-1-1 (b) MAGNETIC FIELDS

Whenever possible, use magnetic field isolation equipment such as a Helmholtz field to surround the monitor. If a Helmholtz field is not available, frequently degauss the unit under test.

Caution: Other electrical equipment may cause

external magnetic fields which may interfere with monitor performance.

Use an external degaussing coil to limit magnetic build up on the monitor. If an external degaussing coil is not available, use the internal degaussing circuit. However, do not use the internal degaussing circuit more than once per 30 minutes.

4-1-1 (c) WARM-UP TIME

The monitor must be on for 30 minutes before starting alignment. Warm-up time is especially critical in color temperature and white balance adjustments.

4-1-1 (d) SIGNAL

Analog, 0.7 Vp-p positive at 75 ohm, internal termination Sync: Separate/Composite (TTL level negative/positive)

Sync-on-Green: Composite sync 0.3 Vp-p negative (Video 0.7 Vp-p positive)

4-1-1 (e) SCANNING FREQUENCY

Horizontal: 30 kHz to 110 kHz (Automatic) Vertical: 50 Hz to 160 Hz (Automatic)

Unless otherwise specified, adjust at the 1024 x 768 mode (H: 68 kHz, V: 85 Hz) signals.

Refer to Table 2-1 on pages 2-2 and 2-3.

4-1-1 (f) HIGH VOLTAGE ADJUSTMENT

Signal: 1024 x 768 mode (68 kHz/85 Hz) Display image: Full white Contrast: Maximum Brightness: Maximum Limit: 27.0 kV ±0.5 kV

(17”: 25 kV ± 0.5 kV)

Measure the hight voltage level at the anode cap. High voltage should be within the limit as above. If the high voltage needs adjustment use the Softjig.

4-1-1 (g) G2 (SCREEN) VOLTAGE ADJUSTMENT

Signal: 1024 x 768 mode (68 kHz/85 Hz) Display image: Full white Contrast: Maximum Brightness: Maximum

Adjust the Screen VR of the FBT so that the G2 (Screen) Voltage for Toshiba it is 620 V ± 10 V.

4-1-1 (h) CENTER RASTER

Adjust VR401 so that the back raster comes to the center when you apply a signal of 91 kHz/85 Hz.

PG17N*/PG19N* 4-1

4 Alignment and Adjustments

This section of the service manual explains how to make permanent adjustments to the monitor. Direction is given for adjustment using the monitor Interface Board Ver. 2.0 and software (Softjig).

4-1 Adjustment Conditions

Caution: Changes made without the Softjig are saved only to the user mode settings. As such, the

settings are not permanently stored and may be inadvertently deleted by the user.

PG17N*

PG19N*

MITSUBISHI

G2 620V

4-1-1 (i) BRIGHTNESS AND CONTRAST

Unless otherwise specified, adjust control volumes:

Brightness: Maximum Contrast: Maximum

4-1-2 Required Equipment

The following equipment may be necessary for adjustment procedures:

4-1-2 (a) DISPLAY CONTROL ADJUSTMENT

1. Non-metallic (–) screwdriver: 1.5 mm Non-metallic (–) screwdriver: 3 mm

2. Philips (+) screwdriver: 1.5 mm

3. Non-metallic hexkey: 2.5 mm

4. Digital Multimeter (DMM), or Digital Voltmeter (DVM)

5. Signal generator, or Computer with a video board that uses the ET-4000 chipset (strongly recommended if using Samsung DM 200 software) and that displays: 1280 x 1024 @ 85 Hz, or 1600 x 1200 @ 85 Hz (maximum).

6. Personal computer

7. Required software: Softjig.exe from Samsung which includes the SF9839TE.MDL (Toshiba CRT) data file Samsung DM200, or DisplayMate for Windows from Sonera Technologies

8. Interface Board Ver. 2.0 Code No. BH81-90001K

9. Parallel communications cable (25-pin to 25-pin); Code No. BH81-90001H

10. Signal cable (15-pin to 15-pin cable with additional 3-pin connector); Code No. BH81-90001J

11. 5 V DC adapter, not supplied

Note: Softjig Ass’y (includes items 8, 9 and 10)

Code No. BH81-90001L

4-1-2 (b) COLOR ADJUSTMENTS

1. All equipment listed in 4-1-2 (a), above

2. Color analyzer, or any luminance measurement equipmen

4-1-3 Connecting the SoftJig

Connect the monitor to the signal generator and/ or PC as illustrated in Figures 4-1 and 4-2.

Note: The signal cable connector which includes

the 3-wire cable must connect to the monitor. If you use Setup 2 (PC only, no signal generator) you can only make adjustments to the signal timing available on that computer system. To make corrections to all factory timings requires the use of an additional signal generator.

4-1-4 After Making Adjustments

After finishing all adjustments, test the monitor in all directions. If, for example, the monitor does not meet adjustment specifications when facing north, reposition the monitor to face east and readjust. This time, try for an adjustment closer to the ideal setting within the tolerance range. Test the unit again in all directions. If the monitor again fails to meet specifications in every direction, contact your Regional After Service Center for possible CRT replacement.

4 Alignment and Adjustments

4-2 PG17N*/PG19N*

MONITOR

INTERFACE BOARD VER. 2.0

SIGNAL GENERATOR

3-WIRE CABLE

SIGNAL CABLE

5V DC ADAPTOR

PARALLEL CABLE

Figure 4-1. Setup 1, With Signal Generator

MONITOR

INTERFACE BOARD VER. 2.0

3-WIRE CABLE

SIGNAL CABLE

PARALLEL CABLE

D-SUB CONNECTOR

5V DC ADAPTOR

Figure 4-2. Setup 2, Without Signal Generator

4-2-1 Centering

Centering means to position the center point of the display in the middle of the display area. Horizontal size and position and vertical size and position control the centering of the display.

Adjust the horizontal size and vertical size to their optimal settings: 352 mm (H) x 264 mm (V). 1280 x 1024 mode (91 kHz/85Hz)

Adjust the horizontal position and vertical position to ≤ 4.0 mm of the center point of the screen.

|A-B| ≤ 4.0 mm. |C-D| ≤ 4.0 mm.

Figure 4-3. Centering

4-2-1 (a) HORIZONTAL SIZE ADJUSTMENT

CONDITIONS

Scanning frequency: 91 kHz/85 Hz Display image: Crosshatch pattern Brightness: Cut-off Contrast: Maximum

Click on the << or >> box next to H_SIZE to adjust the horizontal size of the display pattern to 352 mm. (Tolerance: ± 3 mm.)

4-2-1 (b) VERTICAL SIZE ADJUSTMENT

CONDITIONS

Scanning frequency: 91 kHz/85 Hz Display image: Crosshatch pattern Brightness: Cut-off Contrast: Maximum

Click on the << or >> box next to V_SIZE to adjust the vertical size of the display pattern to 264 mm. (Tolerance: ± 3 mm.)

4-2-1 (c) HORIZONTAL POSITION ADJUSTMENT

CONDITIONS

Scanning frequency: 91 kHz/85 Hz Display image: Crosshatch pattern Brightness: Cut-off Contrast: Maximum

Click on the << or >> box next to H_POSI to center the horizontal image on the raster.

4-2-1 (d) VERTICAL POSITION ADJUSTMENT

CONDITIONS

Scanning frequency: 91 kHz/85 Hz Display image: Crosshatch pattern Brightness: Cut-off Contrast: Maximum

Click on the << or >> box next to V_POSI to center the vertical image on the raster.

4-2-2 Linearity

Linearity affects the symmetry of images as they appear on the screen. Unless each row or column of blocks in a crosshatch pattern is of equal size, or within the tolerances shown in Tables 4-1 and 4-2, an image appears distorted, elongated or squashed.

Table 4-1. Factory Preset Modes Linearity

Table 4-2. Other Modes Linearity: VGA, SVGA, XGA,

MAC, etc.

4-2-2 (a) HORIZONTAL LINEARITY ADJUSTMENT

CONDITIONS

Scanning frequency: 91 kHz/85 Hz Display image: Crosshatch pattern Brightness: Cut-off Contrast: Maximum

To adjust the Horizontal Linearity, refer to Tables 4-1 and 4-2 for the tolerance range.

Click on the << or >> box next to H_LIN to optimize the image.

4 Alignment and Adjustments

PG17N*/PG19N* 4-3

4-2 Display Control Adjustments

DISPLAY AREA

EDGE OF BEZEL

4 : 3

5 : 4

Horizontal: 20.5~23.5 Vertical : 20.5~23.5

Horizontal: 19.18~22.07 Vertical : 20.5~23.5

Supported Timing Mode

Each block (14 %)

Difference between

adjacent blocks (5 %)

Horizontal: Less than 1.10 mm Vertical : Less than 1.10 mm

Horizontal: Less than 1.03 mm Vertical : Less than 1.10 mm

4 : 3

5 : 4

Horizontal: 20.9~23.1 Vertical : 20.9~23.1

Horizontal: 19.60~21.65 Vertical : 20.9~23.1

Standard Modes Linearity

Each block (10 %)

Difference between

adjacent blocks (4 %)

Horizontal: Less than 0.88 mm Vertical : Less than 0.88 mm

Horizontal: Less than 0.82 mm Vertical : Less than 0.88 mm

4-2-2 (b) VERTICAL LINEARITY ADJUSTMENT

CONDITIONS

Scanning frequency: 91 kHz/85 Hz Display image: Crosshatch pattern Brightness: Cut-off Contrast: Maximum

To adjust the Vertical Linearity, refer to Tables 4-1 and 4-2 for the tolerance range.

Click on the << or >> box next to V_LIN to optimize the image.

4-2-3 Trapezoid Adjustment

CONDITIONS

Scanning frequency: 91 kHz/85 Hz Display image: Crosshatch pattern Brightness: Cut-off Contrast: Maximum

Click on the << or >> box next to TRAP to make the image area rectangular.

Figure 4-4. Trapezoid

4-2-4 Pinbalance Adjustment

CONDITIONS

Scanning frequency: 91 kHz/85 Hz Display image: Crosshatch pattern Brightness: Cut-off Contrast: Maximum

Click on the << or >> box next to PIN_BAL to optimize the image.

4-2-5 Parallelogram Adjustment

CONDITIONS

Scanning Frequency: 91 kHz/85 Hz Display image: Crosshatch pattern Brightness: Cut-off Contrast: Maximum

Click on the << or >> box next to PARALL to make the image are rectangular.

Figure 4-6. Parallelogram

4-2-6 Side Pincushion Adjustment

CONDITIONS

Scanning frequency: 91 kHz/85 Hz Display image: Crosshatch pattern Brightness: Cut-off Contrast: Maximum

Click on the << or >> box next to BARREL to straighten the sides of the image area.

4-2-7 Tilt Adjustment

CONDITIONS

Scanning Frequency: 91 kHz/85 Hz Display image: Crosshatch pattern Brightness: Cut-off Contrast: Maximum

Click on the << or >> box next to ROTATE to correct the tilt of the display.

4-2-8 Degauss

No adjustments are available for the degaussing circuit. The degaussing circuit can effectively function only once per 30 minutes.

4-2-9 To Delete the User Mode Data

To delete the adjustment data from the user modes, Press the MENU Button for the 10 Seconds .

4-2-10 Save the Data

To save the adjustment data for a mode, press FACTORY SAVE.

4 Alignment and Adjustments

4-4 PG17N*/PG19N*

| C1 |, | C2 | ≤ 2.0 mm, | D1 |, | D2 | ≤ 2.0 mm.

Figure 4-7. Pincushion

5 mm

| D1 |, | D2 | ≤ 2.0 mm

Figure 4-5. Pinbalance

D1 D2 D1

D2D1

| A - B | < 5 mm

4-3-1 Color Coordinates (Temperature)

Color temperature is a measurement of the radiant energy transmitted by a color. For computer monitors, the color temperature refers to the radiant energy transmitted by white. Color coordinates are the X and Y coordinates on the chromaticity diagram of wavelengths for the visible spectrum.

CONDITIONS

Measurement instrument: Color analyzer Scanning frequency: 68 kHz/85 Hz Display Size : 352 (H) x 264 (V) Display image: White flat field at

center of display area Brightness: Cut-off Contrast: Maximum

PROCEDURE

Use the directions in sections 4-3-2 through 4-3-4 to adjust the color coordinates for: 9300K to x = 0.283 ± 0.02, y = 0.298 ± 0.02 6500K to x = 0.313 ± 0.02, y = 0.329 ± 0.02 5000K to x = 0.346 ± 0.02, y = 0.359 ± 0.02

4-3-2 Color Adjustments for 9300K

4-3-2 (a) BACK RASTER COLOR ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz/85 Hz Display image: Back raster pattern Brightness: Cut-off Contrast: Maximum

1. Select COLOR CHANNEL 1 to control the

color for 9300K.

2. Adjust the luminance of the back raster to

between 0.3 to 1ft-L using the G_CUT controls.

3. Click on the << or >> box next to B_CUT to

set the “y” coordinate to 0.298 ± 0.02.

4. Click on the << or >> box next to R_CUT to

set the “x” coordinate to 0.283 ± 0.02. Note: If the above adjustments cannot be

done to each coordinate, click on the << or >> box next to G_CUT to decrease or increase the green cutoff (bias) and repeat procedures 2 and 3.

4-3-2 (b) G-GAIN ADJUSTMENT

Figure 4-8. Green Box Pattern

CONDITIONS

Scanning frequency: 68 kHz/85 Hz Display image: Green box pattern Brightness: Cut-off Contrast: Maximum

1. Click on the << or >> box next to G_GAIN to

adjust the brightness of the Green Gain to 25 ± 1 ft-L.

Note: If you can’t increase the Green Gain to

the appropriate value, click on the >> box next to increase the ABL point.

4-3-2 (c) WHITE BALANCE ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz/85 Hz Display image: Full white pattern Brightness: Cut-off Contrast: Maximum

Figure 4-9. Full White Pattern

1. Click on the << or >> boxes next to R_GAIN and B_GAIN to make the video white. (For 9300K color adjustment: x = 0.283 ± 0.02, y = 0.298 ± 0.02.)

Note: Do not touch the G_GAIN controls.

2. Check the ABL. If it is not within the specifications (30 ± 1 ft-L), use the ABL controls to adjust it.

3. Select COLOR FACTORY SAVE to save the data.

4 Alignment and Adjustments

PG17N*/PG19N* 4-5

4-3 Color Adjustments

1/3H-1/2H

1/3V-1/2V

FRONT BEZEL OPENING

BACK RASTER

GREEN WINDOW

FRONT BEZEL OPENING

BACK RASTER

WHITE WINDOW

4-3-2 (d) WHITE BALANCE ADJUSTMENT VERIFICATION

CONDITIONS

Scanning frequency: 68 kHz/85 Hz Display image: Back raster pattern X-Y Coordinates: x = 0.283 ± 0.02,

y = 0.298 ± 0.02 Raster Luminance 0.3 ~ 1ft-L ABL Luminance 30 ±1 ft-L Brightness: Cut-off Contrast: Maximum

1. Check whether the color coordinates of the

back raster satisfy the above spec. If they do not, return to 4-3-2 (a) and readjust

all settings.

2. Display a full white pattern. Note: Do not touch the G_GAIN controls.

3. Adjust the Contrast Control on the monitor so

that the luminance of the video is about 5 ft-L.

4. Check whether the white coordinates of the

video meet the above coordinates spec.

5. Adjust the Contrast Control again so that the

luminance of the video is about 20 ft-L.

6. Check whether the white coordinates of the

video satisfies the above spec. If they do not, return to 4-3-2 (a) and readjust

all settings.

4-3-3 Color Adjustments for 6500K

4-3-3 (a) BACK RASTER COLOR ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz/85 Hz Display image: Back raster pattern Brightness: Cut-off Contrast: Maximum

1. Select COLOR CHANNEL 2 to control the

color for 6500K.

2. Adjust the luminance of the back raster to

between 0.3 to 1.0 ft-L using the G_CUT controls.

3. Click on the << or >> boxes next to R_CUT

and B_CUT to adjust the R-Bias to x = 0.313 ±

0.02 and the B-Bias to y = 0.329 ± 0.02.

4-3-3 (b) G-GAIN ADJUSTMENT

This procedure is the same as that for 9300K, refer to the procedure on page 4-5.

4-3-3 (c) WHITE BALANCE ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz/85 Hz Display image: Full white pattern Brightness: Cut-off Contrast: Maximum

1. Click on the << or >> boxes next to R_GAIN and B_GAIN to make the video white. (For 6500K color adjustment: x = 0.313 ± 0.02, y = 0.329 ± 0.02.)

2. Refer to the procedure for 9300K, section 4-3-2 (c) steps 2 and 3.

4-3-3 (d) WHITE BALANCE ADJUSTMENT VERIFICATION

Refer to the procedure for 9300K, section 4-3-2 (d).

4-3-4 Color Adjustments for 5000K

4-3-4 (a) BACK RASTER COLOR ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz/85 Hz Display image: Back raster pattern Brightness: Cut-off Contrast: Maximum

1. Select COLOR CHANNEL 3 to control the color for 5000K.

2. Adjust the luminance of the back raster to between 0.3 to 1.0 ft-L using the G_CUT controls.

3. Click on the << or >> boxes next to R_CUT and B_CUT to adjust the R-Bias to x = 0.346 ±

0.02 and the B-Bias to y = 0.359 ± 0.02.

4-3-4 (b) G-GAIN ADJUSTMENT

This procedure is the same as that for 9300K, refer to the procedure on page 4-5.

Adjust the brightness of the G_GAIN less 5 ft-L than brightness of procedure for 9300K.

4-3-4 (c) WHITE BALANCE ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz/85 Hz Display image: Full white pattern Brightness: Cut-off Contrast: Maximum

1. Click on the << or >> boxes next to R_GAIN and B_GAIN to make the video white. (For 5000K color adjustment: x = 0.346 ± 0.02, y = 0.359 ± 0.02.)

2. Refer to the procedure for 9300K, section 4-3-2 (c) steps 2 and 3.

4 Alignment and Adjustments

4-6 PG17N*/PG19N*

4-3-4 (d) WHITE BALANCE ADJUSTMENT VERIFICATION

Refer to the procedure for 9300K, section 4-3-2 (d).

4-3-5 Luminance Uniformity Check

Luminance is considered uniform only if the ratio of lowest to highest brightness areas on the screen is not less than 7.5:10.

CONDITIONS

Scanning frequency: 68 kHz/85 Hz

(1024 x 768) Display image: White flat field Display size 352 (H) x 264 (V) Brightness: Cut off point Contrast: Maximum

PROCEDURE

Measure luminance at nine points on the display screen (see figure below).

4-3-6 Focus Adjustment

CONDITIONS

Scanning frequency: 68 kHz/85 Hz Display image: “H” character pattern Brightness: Cut off point Contrast: Maximum

PROCEDURE

1. Adjust the Focus VR on the FBT to display the

sharpest image possible.

2. Use Locktite to seal the Focus VR in position.

4-3-7 Color Purity Adjustment

Color purity is the absence of undesired color. Conspicuous mislanding (unexpected color in a uniform field) within the display area shall not be visible at a distance of 50 cm from the CRT surface.

CONDITIONS

Orientation: Monitor facing east Scanning frequency: 68 kHz/85 Hz Display image: White flat field Luminance: Cut off point at the center

of the display area

Note: Color purity adjustments should only be

attempted by qualified personnel.

PROCEDURE

For trained and experienced service technicians only.

Use the following procedure to correct minor color purity problems:

1. Make sure the display is not affected by external magnetic fields.

2. Very carefully break the glue seal between the 2-pole purity convergence magnets (PCM), the band and the spacer.

3. Make sure the spacing between the PCM assembly and the CRT stem is 29 mm ± 1 mm.

4. Display a green pattern over the entire display area.

5. Adjust the purity magnet rings on the PCM assembly to display a pure green pattern. (Optimum setting: x = 0.295 ± 0.015, y = 0.594 ± 0.015)

6. Repeat steps 4 and 5 using a red pattern and then again, using a blue pattern.

Table 4-3. Color Purity Tolerances

(For 9300K color adjustment: x = 0.283 ± 0.02, y = 0.298 ± 0.02)

7. When you have the PCMs properly adjusted, carefully glue them together to prevent their movement during shipping.

4 Alignment and Adjustments

PG17N*/PG19N* 4-7

Red: x = 0.620 ± 0.015 y = 0.334 ± 0.015

Green: x = 0.289 ± 0.015 y = 0.595 ± 0.015

Blue: x = 0.153 ± 0.015 y = 0.072 ± 0.015

Figure 4-10 Luminance Uniformity Check Locations

Memo

4 Alignment and Adjustments

4-8 PG17N*/PG19N*

PG17N*/PG19N* 5-1

5 Troubleshooting

5-1 Parts Level Troubleshooting

Notes: 1. If a picture does not appear, fully rotate the brightness and contrast controls clockwise and reinspect.

2. Check the following circuits.

• No raster appears: Power circuit, Horizontal output circuit, H/V control circuit, and H/V output circuit.

• High voltage develops but no raster appears: Video output circuits.

• High voltage does not develop: Horizontal output circuits.

5-1-1 No Power Supply

Check and replace FG601, D601,

IC661, IC662.

Done.

Repeating start?

Check and replace D601, D604, D663,

Q632, and Q664.

Yes

IC601 Pin 1 waveform is right?

Check and replace IC601,

IC602, IC604.

Yes

IC602 and IC604

are right?

Replace parts and verify voltages.

Yes

Normal operation

Replace Main board.

Yes

WAVEFORMS

Verify voltages.

368 V (IC601, #1)

CH1 P-P = 368 V CH1 RMS = 154.6 V

5 Troubleshooting

5-2 PG17N*/PG19N*

5-1-2 DPMS Failure

Check signal source

H/V sync video level.

Make No H/V sync (power off mode)

LED blinks

Check IC201 Pin 39.

Yes

+12 V line off

Check IC201 Pin 9.

Yes

Q632 Base driving voltage exists?

Check IC201 Pin 10.

Check and replace Q632.

Yes

Done

5 Troubleshooting

PG17N*/PG19N* 5-3

5-1-3 H_Deflection Failure

Q406 Drain waveform is right?

Check R480, D401, +210 V line.

Yes

Q404 gate, drain

waveforms are right?

Check Q404, R415.

Check +25 V line.

Yes

Q405 collector

waveforms are right?

Check and replace D410 and Q405.

Check DY connector connection.

Yes

Check some parts around

Q261 and Q262.

IC261 Pin 8 waveform is right?

Check some parts around IC261.

Yes

WAVEFORMS

13.0 V (Q404, Gate)

CH1 P-P = 13.0 V CH1 RMS = 7.91 V

66.4 V (Q404, Drain)

CH1 P-P = 66.4 V CH1 RMS = 25.84 V

1.24 kV (Q405, Collector)

CH1 P-P = 1.24 kV CH1 RMS = 302 V

1.24 kV (Q406, Drain)

CH1 P-P = 1.24 kV CH1 RMS = 302 V

13.0 V (IC261, #8)

CH1 P-P = 13.0 V CH1 RMS = 7.91 V

5 Troubleshooting

5-4 PG17N*/PG19N*

5-1-4 S Correction Failure

S1~S5 signals are right at each

frequency block?

Check S1 ~ S5 signal.

Check and replace

C451~ C457, Q451~Q455, Q456~Q460 .

Yes

5-1-5 H_Lin. Failure

IC201 Pin 22 voltage varies with

different H_Lin. DAC values?

IC403 Pin 7, 8 voltage varies with

different H_Lin. DAC values?

Check +12 V line.

Check some parts around IC403.

Check L403.

Yes

Check and replace IC201.

Replace IC201.

5-1-6 Invariable H_Size

IC261 Pin 6 voltage varies with

different H_Size DAC values?

Check and replace IC261.

13.6 V (IC261, #6)

CH1 P-P = 13.6 V CH1 RMS =9.02 V

5 Troubleshooting

PG17N*/PG19N* 5-5

5-1-7 Abnormal H_Size

T402 Pin 8 waveform is right?

Check and replace T402.

Check some parts around IC261 Pin 6

and IC201 Pin 20.

Yes

5-1-8 Side Pin or Trap Failure

IC261 Pin 11 output exists?

Check and replace IC261.

5-1-9 Para. or Pin Balance Failure

IC261 Pin 11 output varies with

different DAC values?

Replace IC261.

WAVEFORMS

28.0 V (T402, #8)

CH1 P-P = 28.0 V CH1 RMS = 5.92 V

5 Troubleshooting

5-6 PG17N*/PG19N*

5-1-10 Tilt Failure

IC201 Pin 23 output duty varies

with different DAC values?

IC403 Pin 10, 11 output varies with

different DAC values?

Check and replace IC403.

Check and replace CRT.

Yes

Check and replace IC201.

Check tilt connector connection

5-1-11 V Deflection Failure

±14 V line is on?

IC261 Pin 12 output exists?

Check and replace IC261.

Yes

Refer to 5-1-1 No Power Supply

IC301 Pin 1 input exists?

Check R271 and R304.

Yes

IC301 Pin 6 output exists?

Check and replace some parts

around IC301.

Yes

Check V DY connector connection.

1.32 V (IC261, #12)

CH1 P-P = 1.32V CH1 RMS =1.507 V

55.2 V (IC301, #6)

CH1 P-P = 55.2 V CH1 RMS = 8.04 V

5 Troubleshooting

PG17N*/PG19N* 5-7

5-1-12 V Size or Pos. Variation Failure

IC261 Pin 12 output varies with

different DAC values?

Yes

Check some parts around IC301.

Check bias voltage.

Check and replace IC261 and IC301.

5-1-13 High Voltage Failure

Q524 gate driving pulse exist?

Check +12 V line.

Check and replace Q521, Q522, Q523,

Q524 and IC501.

Yes

Done

1.32 V (IC261, #12)

CH1 P-P = 1.32V CH1 RMS =1.507 V

12.2 V (Q524, Gate)

CH1 P-P = 12.2 V CH1 RMS = 5.30 V

5 Troubleshooting

5-8 PG17N*/PG19N*

IC101 (17”: IC104, Pin12) Pin 15

input exists and

varies with different patterns?

Check and replace IC101

(17”:IC104)

Input full white pattern to monitor.

Yes

T501 Pin 8 output exists?

Check and replace T501.

Yes

IC103 (17”: IC04) Pin 16 output exists and varies with different

patterns?

Check and replace IC103 (17”: IC04).

Yes

Check and replace Q101,

Q102 and +12 V line.

Check CN102.

5-1-14 ABL Failure

5-1-15 Dynamic Focus Failure

IC261 Pin 32 and IC250 Pin 7

output are right?

Check and replace IC250 and IC261.

Yes

Some parts around Q551,

Q552, Q553 and Q554 are right?

Replace failed part.

Yes

Some parts around T502 are right?

Replace failed part.

Check the connection between FBT

Pin 13, CRT Socket PCB.

Yes

WAVEFORMS

4.48 V (IC103, #16)

CH1 P-P = 4.48 V CH1 RMS = 2.652 V

960 mV (IC261, #32)

CH1 P-P = 960 mV CH1 RMS = 6.042 V

5 Troubleshooting

PG17N*/PG19N* 5-9

5-1-16 No Video

IC101 Pins 2, 6 and 11 (17”:

IC104, Pin 5, 8, 10) inputs are

right?

IC101 Pins 29, 32 and 35

(17”: IC104, Pin 25, 28, 30)

outputs are right?

Check I2C bus and +12 V line.

Yes

Check CN101 and BNC B’D IC1.

IC102 Pins 4, 6 and 14 (17”:

IC105, Pin 1, 3, 5) outputs are

right?

Check +12 V line.

Check and replace IC102 (17”: IC105).

Yes

Cathode DC levels are right?

Check +80 V line.

Check and replace IC101 and IC104

(17”: IC104).

Yes

G2 voltage is right?

Check G2 wire, CRT Socket board,

and FBT.

Change CRT.

Yes

Done.

Check signal cable and connection.

1.08 V (IC101, #2)

CH1 P-P = 1.08 V CH1 RMS = 2.930 V

3.52 V (IC101, #35)

CH1 P-P = 3.52 V CH1 RMS = 3.204 V

46.4 V (IC102, #6)

CH1 P-P = 46.4 V CH1 RMS = 47.84 V

5 Troubleshooting

5-10 PG17N*/PG19N*

5-1-17 Micom Failure

IC201 Pin 11 input is right?

IC201 Pins 13 and 14 inputs

are right?

Check X201, C204 and C205.

Yes

Check IC606.

IC201 Pin 18 input is right?

Check IC202.

Yes

All in/output values are right?

Replace IC201.

Yes

Done

WAVEFORMS

24.4 V (IC201, #13)

CH1 P-P = 24.4 V CH1 RMS = 6.32 V

5 Troubleshooting

PG17N*/PG19N* 5-11

5-1-18 OSD Failure

IC103 (17”: IC04) Pin 17 input is

right?

IC103 (17”: IC04) Pin 6 input is

right?

Check and replace Q104 (17”: Q103) .

Yes

Check and replace D302 and Q301.

IC103 (17”: IC04) Pins 7 and 8

inputs are right?

Check IC201 Pins 41 and 42.

Yes

IC103 (17”: IC04) Pins 20, 21 and

22 outputs are right?

Check and replace IC103 (17”: IC04) .

Yes

IC101 (17”: IC104) Pins 4, 9 and 13

inputs are right?

Check and replace QB51,

QG51 and QR51.

Check and replace IC101 (17”: IC104) .

Yes

Done

Check CN102 and connector Ass’y.

(17” only)

6.72 V (IC103, #17)

CH1 P-P = 6.72 V CH1 RMS = 764 mV

5 Troubleshooting

5-12 PG17N*/PG19N*

RL601 operation is right?

Q630 base input is right?

Check and replace Q630.

Yes

Check D-Coil, TH601.

Yes

IC201 Pin 40 output is right?

Check and replace IC201.

Check user function key.

Yes

R217 and R630 are right?

Replace R217 and R630.

Done

Yes

Check degaussing connector.

5-1-20 Degaussing Failure

5-1-19 User Control Failure

IC201 Pins 35 and 36 inputs are

right at each function.

Check and replace function key.

Check and replace IC201.

Done

Yes

Check connector Ass’y.

5 Troubleshooting

PG17N*/PG19N* 5-13

5-2 General Troubleshooting

5-2-1 No Picture

LED blinks?

LED is green color?

After restart monitor LED don’t

come on, repair power circuit.

Check signal cable.

Check G2 voltage, high voltage,

R, G, B cathode voltage.

Yes

LED is Amber color?

Yes

5-2-2 Shut down

Yes

5-2-2 Shut Down

Blinking LED’s?

Scan failure

Check horizontal, vertical deflection

system and check power supply

secondary voltages.

Yes

Check power supply.

High voltage failure?

Check high voltage system.

Check and replace IC201.

Done

Yes

Video failure?

Check Video board.

Yes

5 Troubleshooting

5-14 PG17N*/PG19N*

5-2-3 Missing Color

Are proper Video levels

on CN101 (D-Sub) Pins 1, 2 and 3,

R-BNC, G-BNC and B-BNC.

Are proper AC voltage on all

cathodes?

Refer to 5-1-16 No Video.

Yes

Check signal generator and cathode.

Are proper DC voltage on all

cathodes?

Check IC104 (17”: IC104 Pins 19, 20,

and 21) Pins 10, 11 and 12.

Check QB02, QB03, QG02, QG03

QR02 and QR03.

Change the CRT.

Done

Yes

Is G2 voltage right?

Check G2 wire, G2 control, volume

and FBT.

Yes

5 Troubleshooting

PG17N*/PG19N* 5-15

Is G2 voltage right?

Is blank pulse on Pin 27 of IC101

(17”: Pin 23 of IC104) on Video

board?

Check CN102, Q104 (17”: Q103).

Yes

Check G2 control volume and FBT.

Is blank pedestal on

Pins 29, 32 and 35 of IC101

(17”:

25, 28, 30 of IC104)

Check IC101 (17”: IC104) and related

components.

Yes

Is V_FLB pulse on

Pin 17 of IC103 (17”: IC04)?

Check Q301.

Done

Yes

Is blank pedestal on all cathodes?

Check Pins 24, 25 and 26 of IC101

(17”: 19, 20, 21 of IC104)

Check QB02, QB03, QG02, QG03,

QR02 and QR03.

Yes

Check white balance adjustment.

5-2-4 Visible Retrace

5 Troubleshooting

5-16 PG17N*/PG19N*

Are signals right?

Signals at Pins 1, 3 and 5 of IC1

are right?

Replace IC1.

Yes

Check Video cable.

Signals at CN201 Pins 6, 9 and

CN102 Pin 6 are right?

Check wire dressing and connections.

Check circuits on Main board.

(IC201 and IC261)

Yes

Done

Check input signals Pins 1, 2

and 3 of D-SUB connector.

5-2-5 Unsynchronized Image

5 Troubleshooting

PG17N*/PG19N* 5-17

Is the convergence now

within spec?

Readjust convergence.

Done

Yes

Is the convergence now

within spec?

Done

Change CRT and readjust

convergence.

Done

Yes

Try readjusting convergence.

5-2-6 Misconvergence

5 Troubleshooting

5-18 PG17N*/PG19N*

Improved focus?

Check focus leads from FBT

to CRT Socket.

Check the CRT Socket.

Aging monitor and check for focus

change.

Yes

Is dynamic focus circuit right?

Refer to 5-1-15 Dynamic

Focus Failure.

Replace the CRT and verify focus.

Yes

Adjust focus VR.

5-2-7 Poor Focus

5-2-8 Purity Failure

Purity is right?

Degaussing circuit is right?

Refer to 5-1-20 Degaussing Failure.

Replace CRT and verify purity.

Yes

Done

Yes

Degaussing

6 Exploded View and Parts List

6-1 Front Cover & CRT Ass’y (PG17N*)

PG17N*/PG19N* 6-3

1 2 3 4 5 6

DESCRIPTION UNIT/COVER-FRONT SCREW ASS’Y TAPTITE SCREW-TAPTITE UNIT/SHIELD-VIDEO COVER/VIDEO SUPPORT/CDT

CODE-NO(PG17NS)

BH75-00107A

6006-001010

6003-000010 BH75-00132A BH71-00021A BH72-00085A

SPECIFICATION

ABS HB WPP,BH,+, D5, L25 M3,L10,W/W, BH+

PG17XS

SPTE TO. 2

ABS HB

Q’TY

1 2 3 1 1 2

6-2 Chassis & Stand Ass’y (PG17N*)

6 Exploded View & Parts List

6-4 PG17N*/PG19N*

7 8

9 10 11 12 13 14 15 18

DESCRIPTION SCREW-TAPTITE SCREW-TAPTITE SHIELD/PCB-COVER UNIT/SHIELD-BOTTON GUIDE/POWER SHAFT/POWER SCREW-TAPTITE UNIT/BRKT-BNC UNIT/SHIELD-BNC UNIT/STAND-ASS’Y

CODE-NO(PG17NS)

6003-000009

6003-000010 BH75-00053A BH75-00095A BH72-60765A BH72-60736A

6003-000010 BH75-00069A BH75-00131A BH75-00122A

SPECIFICATION

M4,L16, BH+

M3,L10,W/W,BH+

AL+PC, V0,T0.5

SECC-1,T1.0,0-CL

ABS HB ABS HB

M3, L10, W/W, BH+

SPTE T0.5

PG17NS ABS HB

Q’TY

1 2 1 1 1 1 6 1 1 1

6-3 Rear Cover Ass’y (PG17N*)

6 Exploded View & Parts List

PG17N*/PG19N* 6-5

16 17

DESCRIPTION UNIT/SHIELD-COVER UNIT/COVER-REAR

CODE-NO(PG17NS)

BH75-00099A BH75-00109A

SPECIFICATION

AL050S T0.3

ABS HB

Q’TY

1 1

6 Exploded View & Parts List

6-6 PG17N*/PG19N*

6-4 Front Cover & CRT Ass’y (PG19N*)

1 2 3 4

18 19 20

DESCRIPTION UNIT/COVER-FRONT CDT UNIT/SHIELD/CDT SCREW-ASS’Y

UNIT-SHIELD/VIDEO VIDEO-PCB UNIT-COVER/VIDEO

CODE-NO

BH75-00108A

BH75-00094A 6006-001010

BH75-00061A

BH75-00085B

SPECIFICATION

ABS HB IV16

PG19NS

SECC T0.5-CL,X,E16

W/W 5X30

AL1050S T1.0

PG19NS

SPTE T0.2

Q’TY

1 1 1 4

1 1 1

REMARK

C/F-CDT+S/CDT

UNIT-BRKT/SUPPORTBH75-00102A SECC T0.5-CL,X,E16

6-5 Chassis & Stand Ass’y (PG19N*)

6 Exploded View & Parts List

PG17N*/PG19N* 6-7

6 7 8

9 10 11 12 13 14 15 16 17 24

DESCRIPTION THERMAL-SENSOR/PCB CLAMP-PCB UNIT-SHIELD/BOTTOM MAIN-PCB/ASSY SCREW-TAPTITE SHIELD-BNC/REAR BNC-PCB BRKT-BNC SCREW-TAPTITE PURITY-CONTROL/PCB UNIT-SHIELD-BNC/COVER SCREW-TAPTITE UNIT-STAND

CODE-NO

6502-000127

BH75-00095A

6003-000010

BH71-00020A

BH75-00062A

6003-000010

BH75-00127A

6003-000010

BH75-00123A

SPECIFICATION

PG19NS

NYLCN 66

SECC T1.0-CL,X,E16

PG19NS

W/W 3X10

SPTE T0.2

PG19NS

SPTE T0.5

W/W 3X10

PG19NS

SECC T0.5-CL,X,E16

W/W 3X10

ABS HB IV16

Q’TY

1 2 1 1 6 1 1 1 2 1 1 3 1

REMARK

M/PCB+C/BNC

PU/PCB+C/BNC

B/BNC+C/BNC

6-6 Rear Cover Ass’y (PG19N*)

6 Exploded View & Parts List

6-8 PG17N*/PG19N*

NO 21 22 23

DESCRIPTION UNIT-SHIELD/COVER SCREW-TAPTITE UNIT-COVER REAR

CODE-NO

BH75-00100A

6003-000010

BH75-00110A

SPECIFICATION

AL1050S T0.3

W/W 3X10

ABS HB IV16

Q’TY

1 6 1

REMARK

S/COVER+S/CDT

BD261 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 BD262 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 BD266 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 BD401 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 BD402 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 BD403 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 BD532 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 BD602 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 BD605 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 BD630 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 BD631 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 BD651 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 BD663 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 C201 2401-001101 C-AL 330uF,20%,16V,GP,TP,8x11.5,5 C202 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5 C203 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP C204 2201-000389 C-CERAMIC,DISC 0.022nF,5%,50V,NP0,TP,5x3 C205 2201-000798 C-CERAMIC,DISC 0.01nF,0.5pF,50V,NP0,TP,4 C206 2401-000028 C-AL 10uF,20%,50V,GP,TP,5x11,5 C207 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5 C208 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5 C209 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5 C210 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C211 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C212 2201-000144 C-CERAMIC,DISC 0.1nF,5%,50V,NP0,TP,8.5x3 C213 2201-000017 C-CERAMIC,DISC 1nF,10%,50V,Y5P,TP,5x3.5 C214 2401-000050 C-AL 10uF,20%,16V,GP,TP,5x11,2.5 C217 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C218 2401-000028 C-AL 10uF,20%,50V,GP,TP,5x11,5 C219 2201-000144 C-CERAMIC,DISC 0.1nF,5%,50V,NP0,TP,8.5x3 C220 2201-000144 C-CERAMIC,DISC 0.1nF,5%,50V,NP0,TP,8.5x3 C221 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C222 2401-000050 C-AL 10uF,20%,16V,GP,TP,5x11,2.5 C223 2201-000138 C-CERAMIC,DISC 100pF,10%,50V,Y5P,TP,4.0X C224 2401-001509 C-AL 47uF,20%,16V,GP,TP,5x7mm,5 C225 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C226 2301-000481 C-FILM,PEF 10nF,5%,100V,TP,6.5x3.4x12.5 C227 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP C228 2201-000370 C-CERAMIC,DISC 0.22nF,10%,50V,Y5P,TP,4x3 C250 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP C251 2201-000144 C-CERAMIC,DISC 0.1nF,5%,50V,NP0,TP,8.5x3 C252 2201-000144 C-CERAMIC,DISC 0.1nF,5%,50V,NP0,TP,8.5x3 C253 2201-000163 C-CERAMIC,DISC 10nF,+80-20%,50V,Y5V,TP,7 C254 2401-000443 C-AL 10uF,20%,25V,GP,TP,5x5mm,2mm C255 2201-000163 C-CERAMIC,DISC 10nF,+80-20%,50V,Y5V,TP,7

PG17N*/PG19N* 7-1

Loc. No. Code No. Description Specification Remarks

7 Electrical Parts List

7-1 Main PCB Parts

C256 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5 C257 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP C258 2201-000144 C-CERAMIC,DISC 0.1nF,5%,50V,NP0,TP,8.5x3 C265 2301-000014 C-FILM,PEF 6.8nF,5%,100V,TP,5.8x12.5mm,5 C268 2401-000028 C-AL 10uF,20%,50V,GP,TP,5x11,5 C269 2301-000102 C-FILM,PEF 1.2nF,5%,100V,TP,5.4x10mm,5mm C271 2202-000669 C-CERAMIC,MLC-RADIAL 10nF,10%,50V,X7R,TP C272 2301-001049 C-FILM,MPEF 150nF,5%,100V,TP,10.5x5x14.5 C273 2301-000014 C-FILM,PEF 6.8nF,5%,100V,TP,5.8x12.5mm,5 C278 2401-000698 C-AL 2200uF,20%,16V,WT,TP,12.5x25,5 C279 2401-000028 C-AL 10uF,20%,50V,GP,TP,5x11,5 C282 2305-000665 C-FILM,MPEF 100nF,5%,63V,TP,7.5x4.0x5.0m C284 2305-001039 C-FILM,MPEF 270nF,5%,63V,TP,7.5x5x14,5mm C285 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C301 2401-000142 C-AL 1000uF,20%,16V,WT,TP,10x20,5 C302 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C305 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP C306 2401-000852 C-AL 220uF,20%,35V,GP,TP,8x11.5mm,5 C307 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP C308 2305-000237 C-FILM,MPEF 1uF,5%,63V,TP,7.5x15.5mm,5mm C309 2301-000294 C-FILM,PEF 56nF,5%,100V,TP,9.5x12.5mm,5m C310 2301-000287 C-FILM,PEF 5.6nF,5%,100V,TP,10.5x12.5x6 C311 2401-000142 C-AL 1000uF,20%,16V,WT,TP,10x20,5 C312 2401-000597 C-AL 1uF,20%,50V,GP,TP,4x7mm,1.5mm C313 2301-000013 C-FILM,PEF 4.7nF,5%,100V,TP,10.5x12.5x6 C321 2401-000028 C-AL 10uF,20%,50V,GP,TP,5x11,5 C401 2301-000016 C-FILM,PEF 22nF,5%,100V,TP,7.2x4.5x9.0mm C402 2401-001509 C-AL 47uF,20%,16V,GP,TP,5x7mm,5 C403 2301-001322 C-FILM,PPF 33nF,5%,250V,TP,17.5x5x11mm,7 C405 2305-000237 C-FILM,MPEF 1uF,5%,63V,TP,7.5x15.5mm,5mm C406 2401-001561 C-AL 47uF,20%,35V,WT,TP,8x11.5,5 C407 2201-000291 C-CERAMIC,DISC 1nF,10%,500V,Y5P,TP,7.5x3 C408 2305-000624 C-FILM,MPEF 330nF,10%,100V,TP,5mm C409 2305-000624 C-FILM,MPEF 330nF,10%,100V,TP,5mm C410 2301-000020 C-FILM,PEF 27nF,5%,100V,TP,7.3x4x12.5mm C411 2301-001180 C-FILM,PPF 2.2nF,5%,3KV,TP,22.5x15.5x22 C412 2303-000007 C-FILM,PPF 2.7nF,5%,2.5KV,TP,28.5X19X12m C414 2201-002079 C-CERAMIC,DISC 0.15nF,10%,500V,Y5P,TP,6 C415 2401-000040 C-AL 47uF,20%,250V,WT,TP,16x25mm,7 C416 2401-003080 C-AL 3.3UF,20%,50V,BP,TP,5X11,2.5 C417 2401-000050 C-AL 10uF,20%,16V,GP,TP,5x11,2.5 C418 2301-000102 C-FILM,PEF 1.2nF,5%,100V,TP,5.4x10mm,5mm C419 2201-000129 C-CERAMIC,DISC 0.1nF,10%,1kV,Y5P,TP,7x4 C421 2305-000624 C-FILM,MPEF 330nF,10%,100V,TP,5mm C431 2301-000005 C-FILM,PEF 33nF,5%,100V,TP,5.8x12.5x3,5 C451 2301-001259 C-FILM,MPPF 100nF,5%,400V,TP,19x8x16,7.5 C452 2301-001259 C-FILM,MPPF 100nF,5%,400V,TP,19x8x16,7.5

7 Electrical Parts List

7-2 PG17N*/PG19N*

Loc. No. Code No. Description Specification Remarks

C453 2306-000179 C-FILM,MPPF 300nF,5%,250V,TP,20x18.5x10 C454 2306-000249 C-FILM,MPPF 680nF,5%,250V,TP,26x20.5x12 C455 2306-000147 C-FILM,MPPF 1uF,5%,250V,BK,26x24x15,22.5 C456 2306-000131 C-FILM,MPPF 150nF,5%,250V,TP,19x16x7.5,7 C457 2301-001249 C-FILM,MPPF 68nF,5%,400V,TP,19x7x15mm,7 C501 2301-001027 C-FILM,PEF 15nF,10%,250V,TP,9.5x12x4.5,5 C502 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP C503 2401-000028 C-AL 10uF,20%,50V,GP,TP,5x11,5 C504 2401-001576 C-AL 47uF,20%,50V,GP,TP,8x11.5,5 C505 2401-003224 C-AL 470uF,20%,16V,WT,TP,8X11.5,5mm C521 2301-000294 C-FILM,PEF 56nF,5%,100V,TP,9.5x12.5mm,5m C522 2301-000016 C-FILM,PEF 22nF,5%,100V,TP,7.2x4.5x9.0mm C523 2401-000317 C-AL 100uF,20%,25V,WT,TP,8x11.5,5 C524 2201-000163 C-CERAMIC,DISC 10nF,+80-20%,50V,Y5V,TP,7 C525 2305-001041 C-FILM,MPEF 220nF,5%,63V,TP,7.5x4.5x13.5 C526 2305-000665 C-FILM,MPEF 100nF,5%,63V,TP,7.5x4.0x5.0m C527 2401-001576 C-AL 47uF,20%,50V,GP,TP,8x11.5,5 C528 2401-000010 C-AL 220uF,20%,16V,GP,6.3x11mm,2 C530 2201-000469 C-CERAMIC,DISC 0.33nF,10%,500V,Y5P,TP,5 C531 2303-000147 C-FILM,PPF 1NF,5%,2KV,TP,23X13X8MM,7.5 C532 2401-000638 C-AL 2.2uF,20%,350V,WT,TP,10x12.5mm C533 2201-000732 C-CERAMIC,DISC 0.68nF,10%,1kV,Y5P,TP,7x4 C534 2401-001576 C-AL 47uF,20%,50V,GP,TP,8x11.5,5 C535 2401-000771 C-AL 220uF,20%,100V,WT,TP,16x25,7.5 C536 2401-003080 C-AL 3.3UF,20%,50V,BP,TP,5X11,2.5 C537 2401-000638 C-AL 2.2uF,20%,350V,WT,TP,10x12.5mm C538 2305-000665 C-FILM,MPEF 100nF,5%,63V,TP,7.5x4.0x5.0m C539 2401-003375 C-AL 2.2uF,20%,50V,BP,TP,5x11,5 C540 2201-000732 C-CERAMIC,DISC 0.68nF,10%,1kV,Y5P,TP,7x4 C551 2401-000043 C-AL 1uF,20%,160V,GP,TP,6.3x11,5 C552 2305-000004 C-FILM,MPEF 220nF,10%,100V,TP,12.7x16,5m C556 2201-000551 C-CERAMIC,DISC 0.47nF,10%,1kV,Y5P,TP,6.3 C558 2201-000144 C-CERAMIC,DISC 0.1nF,5%,50V,NP0,TP,8.5x3 C603 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP C604 2301-001285 C-FILM,MPPF 680NF,10%,275V,BK,31X11X21MM C605 2201-000023 C-CERAMIC,DISC 2.2nF,20%,125V,Y5U,TP,11x C606 2201-000023 C-CERAMIC,DISC 2.2nF,20%,125V,Y5U,TP,11x C607 2401-000015 C-AL 33uF,20%,50V,WT,6.3x11mm,2.5 C608 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C609 2401-001137 C-AL 330uF,20%,400V,GP,BK,30x45mm,1 C610 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP C611 2201-000012 C-CERAMIC,DISC 0.22nF,10%,1kV,Y5P,TP,6.3 C612 2201-000129 C-CERAMIC,DISC 0.1nF,10%,1kV,Y5P,TP,7x4 C614 2301-000016 C-FILM,PEF 22nF,5%,100V,TP,7.2x4.5x9.0mm C615 2301-001049 C-FILM,MPEF 150nF,5%,100V,TP,10.5x5x14.5 C616 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5 C617 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm

!!!

7 Electrical Parts List

PG17N*/PG19N* 7-3

Loc. No. Code No. Description Specification Remarks

C633 2401-000010 C-AL 220uF,20%,16V,GP,6.3x11mm,2 C634 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5 C635 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C636 2401-000235 C-AL 100uF,20%,100V,WT,TP,12.5x20,5 C637 2401-000142 C-AL 1000uF,20%,16V,WT,TP,10x20,5 C638 2401-000040 C-AL 47uF,20%,250V,WT,TP,16x25mm,7 C639 2401-003224 C-AL 470uF,20%,16V,WT,TP,8X11.5,5mm C640 2401-000142 C-AL 1000uF,20%,16V,WT,TP,10x20,5 C641 2301-000013 C-FILM,PEF 4.7nF,5%,100V,TP,10.5x12.5x6 C642 2401-001838 C-AL 470uF,20%,25V,WT,TP,10x16,5 C643 2401-000142 C-AL 1000uF,20%,16V,WT,TP,10x20,5 C644 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5 C645 2401-001422 C-AL 470uF,20%,35V,WT,TP,12.5x25,5 C646 2401-003486 C-AL 680uF,20%,16V,WT,TP,10x16mm,5 C647 2301-000174 C-FILM,PEF 15nF,5%,100V,TP,7.2x4.0x7.5mm C648 2301-000004 C-FILM,PEF 2.2nF,5%,100V,TP,5.5X10X2.9,5 C649 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP C652 2301-000481 C-FILM,PEF 10nF,5%,100V,TP,6.5x3.4x12.5 C653 2201-000023 C-CERAMIC,DISC 2.2nF,20%,125V,Y5U,TP,11x C654 2201-000023 C-CERAMIC,DISC 2.2nF,20%,125V,Y5U,TP,11x C656 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP C661 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5 C662 2401-000010 C-AL 220uF,20%,16V,GP,6.3x11mm,2 C663 2401-000028 C-AL 10uF,20%,50V,GP,TP,5x11,5 C664 2201-000129 C-CERAMIC,DISC 0.1nF,10%,1kV,Y5P,TP,7x4 C665 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm C666 2401-000913 C-AL 22uF,20%,16V,GP,TP,5x11mm,2.5m C668 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP CIS BH39-00059A CBF-HARNESS 3P/3P,420MM,GRY,UL2547,AWG26 CIS BH39-00083A CBF-HARNESS 15P/15P,220MM,BLU/WHT/BLK/RE CIS BH39-00085A CBF-HARNESS 10P/4P,400MM,GRN/BLK/BRN/YEL CIS BH39-00086A CBF-HARNESS 13P/2,3,4P,420MM,BLU/RED/WHT CIS 1204-001508 IC-VERTICALDEF. KA2142,SIP,10P,PLASTIC CIS 1203-000001 IC-POSI.FIXEDREG. 7805,TO-220,3P,PLAST CIS 1203-000165 IC-POSI.ADJUSTREG. 78R12,TO-220,3P,1 CIS 0505-001266 FET-SILICON 2SK2761-01MR,N,600V,10A,0.85 CIS 0502-000348 TR-POWER TIP29C,NPN,2W,TO-220,15-75 CIS 0502-000351 TR-POWER TIP30,PNP,2W,TO-220AB,15-75 CIS 0402-001289 DIODE-RECTIFIER 31DF6,600V,3A,DO-201AD,B CIS BH13-00012A IC-POWERSWITCH PG17/19/21,DP308O,TO-3P-5 CIS 0402-001227 DIODE-BRIDGE D3SBA60,600V,2.3A,SIP-4,BK CIS 0505-001359 FET-SILICON SFP9634,P,-250V,-5A,1.3OHM,7 CIS 0402-001215 DIODE-RECTIFIER SDS10U150S,1.5KV,10A,TO CIS 0502-001142 TR-POWER 2SC5584,NPN,150W,TO-3PL,ST,7-1 CIS 0505-001305 FET-SILICON SKS10N20,N,200V,6.9A,0.36OHM CIS 0505-001358 FET-SILICON SKS19N20,N,200V,11.8A,0.15OH CIS BH72-00120A SHAFT-POWER PG19NO,ABS+PC,5V,IV16

!!!

7 Electrical Parts List

7-4 PG17N*/PG19N*

Loc. No. Code No. Description Specification Remarks

CIS 0402-001294 DIODE-RECTIFIER UF5404L-5709,400V,3A,DO CIS 3301-000130 CORE-FERRITE AC,23.5x9.4x12.6mm,1500,280 CIS 6501-000004 CABLETIE DA-80,T1,W2.5,L80,NTR,NYLON66 CN201 3711-004379 CONNECTOR-HEADER BOX,4P,1R,2MM,STRAIGHT CN202 3711-004379 CONNECTOR-HEADER BOX,4P,1R,2MM,STRAIGHT CN203 3711-004351 CONNECTOR-HEADER NOWALL,16P,1R,2.54MM,ST CN204 3711-004352 CONNECTOR-HEADER BOX,15P,1R,2MM,STRAIGHT CN205 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN206 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN207 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN209 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN211 3711-004349 CONNECTOR-HEADER BOX,3P,1R,2MM,STRAIGHT CN212 3711-004349 CONNECTOR-HEADER BOX,3P,1R,2MM,STRAIGHT CN401 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN402 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN403 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN404 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN405 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN406 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN407 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN408 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN409 3711-000821 CONNECTOR-HEADER BOX,2P,1R,2.5mm,STRAIGH CN410 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN411 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN412 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN413 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN415 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN416 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN417 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN601 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN602 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN603 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN605 3711-000012 CONNECTOR-HEADER BOX,4P,1R,2.5mm,STRAIGH CN606 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN607 3711-003942 CONNECTOR-HEADER BOX,2P,1R,2mm,STRAIGHT D201 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D202 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D203 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D260 0402-001039 DIODE-RECTIFIER SB020,20V,600mA,MPG06,TP D263 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D264 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D265 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D301 0402-000272 DIODE-RECTIFIER UF4001,50V,1A,DO-41,TP D302 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D401 0402-000249 DIODE-RECTIFIER RG4,400V,1.5A D404 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D405 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP D409 0402-001069 DIODE-RECTIFIER RL10Z,200V,2A,DO,TP D411 0402-000007 DIODE-RECTIFIER 1N4937GP,600V,1A,DO-41,T

!!!

7 Electrical Parts List

PG17N*/PG19N* 7-5

Loc. No. Code No. Description Specification Remarks

D412 0402-000007 DIODE-RECTIFIER 1N4937GP,600V,1A,DO-41,T D413 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP D451 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP D501 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T D502 0402-001114 DIODE-RECTIFIER 1N4936GP,400V,1A,DO-204A D503 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D504 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D506 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D521 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D522 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D523 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D524 0402-001295 DIODE-RECTIFIER GUR460L-5700,600V,4A,DOD525 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP D526 0402-001295 DIODE-RECTIFIER GUR460L-5700,600V,4A,DOD527 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TP D528 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP D529 0402-000007 DIODE-RECTIFIER 1N4937GP,600V,1A,DO-41,T D530 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D551 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D552 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D553 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D554 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D602 0403-001028 DIODE-ZENER BZT03C160,160V,153-171V,3.25 D604 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,T D605 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TP D607 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TP D630 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D631 0402-001118 DIODE-RECTIFIER UF1G,400V,1.2A,DO-204AL D633 0402-000250 DIODE-RECTIFIER RG4C,1000V,1A D634 0402-001190 DIODE-RECTIFIER RG10Z,200V,1.2A,DO-15,TP D635 0402-001118 DIODE-RECTIFIER UF1G,400V,1.2A,DO-204AL D636 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP D638 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP D639 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D640 0402-001190 DIODE-RECTIFIER RG10Z,200V,1.2A,DO-15,TP D661 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP D662 0402-000126 DIODE-RECTIFIER 1N4001GP,50V,1A,DO-41,TP D663 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T D664 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 EY301 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY302 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY401 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY402 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY403 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY404 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY405 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH EY408 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH

!!!!!!!

7 Electrical Parts List

7-6 PG17N*/PG19N*

Loc. No. Code No. Description Specification Remarks

EY409 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH EY410 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH EY411 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH EY412 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY413 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY414 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH EY415 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH EY501 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY502 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY503 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH EY504 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH EY505 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH EY506 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH EY507 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH EY508 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH EY509 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH EY510 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH EY511 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH EY6 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY601 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH EY602 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH EY603 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY604 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY605 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY606 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY607 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY608 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY609 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY61 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY610 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY611 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY612 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY613 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH EY614 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH EY615 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH EY616 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH F633 3601-001199 FUSE-FERRULE 125V,3A,Slow-blow,EPOXY,3.1 FBT_CORE 3301-000233 CORE-FERRITE ZZ,18x9.5x28mm FBT+H/S 6003-000009 SCREW-TAPTITE BH,+,B,M4,L16,ZPC(YEL),SWR FG601 3601-000455 FUSE-FERRULE 250V,4A,TL,GLASS,5.2X20MM FH601 3602-000001 FUSE-CLIP 30mohm IC201 0903-001166 IC-MICROCONTROLLER 88P6232,8BIT,DIP,42P IC201_SOCK 3704-001071 SOCKET-IC 42P,DIP,SN,1.778mm IC202 1203-000495 IC-RESET 7045,T0-92,3P,PLASTIC,4.3/4 IC203 1103-001150 IC-EEPROM 24C081,8KBIT,DIP,8P,300MIL,10M IC204 1103-001087 IC-EEPROM 24LC21,128x8BIT,DIP,8P,300MIL IC250 BH13-10335H IC-UNIFORMITY S-PROJECT,M52759SP,DIP,20P

7 Electrical Parts List

PG17N*/PG19N* 7-7

Loc. No. Code No. Description Specification Remarks

IC261 1204-001509 IC-HOR./VER.PROCESSO TDA4859,DIP,32P,400 IC403 BH13-00009A IC-H/VCONVERGENCE PG17/19,AN5452,SIP,12P IC501 1203-000610 IC-PWMCONTROLLER 494,DIP,16P,300MIL,PLAS IC502 1201-000420 IC-OPAMP 358,DIP,8P,300MIL,DUAL,100V/mV IC602 0604-001018 PHOTO-COUPLER DAR-TR,63-125%,200mW,DIP-4 IC604 1203-000002 IC-POSI.ADJUSTREG. 431,TO-92,3P,PLAST IC661 0604-001018 PHOTO-COUPLER DAR-TR,63-125%,200mW,DIP-4 IC662 BH13-00010A IC-POWERSWITCH S-III,TNY254P,DIP,8P,POWE JUMP BH39-40305Y CBF-HARNESS 110MM,BLK,1015,AWG22 L250 2701-000115 INDUCTOR-AXIAL 10uH,10%,3x7mm L400 2701-000179 INDUCTOR-AXIAL 33uH,10%,4.2x9.8mm L401 BH27-00034A COIL-CHOKE 5.0mH,DR1523,BK L402 BH27-00032A COIL-HORIZ.CENTER 2.7mH,DR15*23 L403 BH26-00071A TRANS-H.LINEARITY 49.0mH/3.5uH,5P,DR1420 L404 BH27-00038A COIL-CHOKE 70uH,DR0811(C:3.5),BK L501 2701-000179 INDUCTOR-AXIAL 33uH,10%,4.2x9.8mm L502 2701-000187 INDUCTOR-AXIAL 4.7uH,10%,4.2x9.8mm L521 BH27-00027A COIL-CHOKE-1 8.5UH,DR1215(C:7.0),BK L601 BH27-00025A COIL-LINEFILTER 24.0MH,SQE-2828,BK LC601 2901-001173 FILTER-EMIACLINE 250V,3A,UL/CSA/TUV/SEMK MP1.0 BH41-00041A P.C.B-MAIN FR1,1 OP1 0601-000334 LED CBI-ANGLE,GRN/YEL,4.8MM,565/585NM POS601 1404-001154 THERMISTOR-PTC 4.5OHM,+30%/-20%,220V,270 Q261 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q262 0501-000303 TR-SMALLSIGNAL KSA733,PNP,250mW,TO-92,TP Q263 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q264 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q290 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q301 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q402 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q403 0501-000303 TR-SMALLSIGNAL KSA733,PNP,250mW,TO-92,TP Q404 0505-001357 FET-SILICON SKS4N20,N,200V,3A,1.3OHM,27W Q451 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q452 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q453 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q454 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q455 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q460 0505-001305 FET-SILICON SKS10N20,N,200V,6.9A,0.36OHM Q501 0501-000143 TR-SMALLSIGNAL 2N6520,PNP,625mW,TO-92 Q521 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP Q522 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP Q523 0501-000581 TR-SMALLSIGNAL 2N3906,PNP,625mW,TO-92,TP Q553 0501-000140 TR-SMALLSIGNAL 2N5551,NPN,625mW,TO-92 Q554 0501-000413 TR-SMALLSIGNAL KSP44,NPN,625mW,TO-92,5 Q630 0501-000010 TR-SMALLSIGNAL KSC1008,NPN,800mW,TO-92,T Q632 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP Q663 0501-000586 TR-SMALLSIGNAL KSC945,NPN,250mW,TO-92,TP

!!!

7 Electrical Parts List

7-8 PG17N*/PG19N*

Loc. No. Code No. Description Specification Remarks

Q664 0501-000303 TR-SMALLSIGNAL KSA733,PNP,250mW,TO-92,TP R201 2001-000613 R-CARBON 3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM R202 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R203 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R204 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R205 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R206 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R207 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R208 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM R209 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM R210 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM R211 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R212 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R213 2001-000435 R-CARBON 1MOHM,5%,1/8W,AA,TP,1.8X3.2MM R214 2001-000515 R-CARBON 220OHM,5%,1/8W,AA,TP,1.8X3.2MM R215 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R216 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R217 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R218 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R219 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R220 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R221 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R223 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R224 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R225 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R226 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R229 2001-000977 R-CARBON 8.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R230 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R231 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R232 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R233 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R234 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM R235 2001-000331 R-CARBON 12KOHM,5%,1/8W,AA,TP,1.8X3.2MM R236 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R237 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R238 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R239 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R240 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R241 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R242 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R243 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R244 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R245 2001-000241 R-CARBON 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM R246 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R250 2004-000176 R-METAL 1.8Kohm,1%,1/4W,AA,TP,2.4x6.4m R252 2004-000344 R-METAL 15Kohm,1%,1/4W,AA,TP,2.4x6.4mm R253 2004-000728 R-METAL 3.9Kohm,1%,1/4W,AA,TP,2.4x6.4m

7 Electrical Parts List

PG17N*/PG19N* 7-9

Loc. No. Code No. Description Specification Remarks

R254 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R255 2004-001136 R-METAL 6.8Kohm,1%,1/4W,AA,TP,2.4x6.4m R256 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R257 2004-000796 R-METAL 33Kohm,1%,1/4W,AA,TP,2.4x6.4mm R262 2004-000532 R-METAL 20Kohm,1%,1/4W,AA,TP,2.4x6.4mm R263 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R264 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R265 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R266 2004-000970 R-METAL 470ohm,1%,1/4W,AA,TP,2.4x6.4mm R267 2004-000498 R-METAL 2.7Kohm,1%,1/4W,AA,TP,2.4x6.4m R268 2001-000032 R-CARBON 180OHM,5%,1/4W,AA,TP,2.4X6.4MM R269 2004-000796 R-METAL 33Kohm,1%,1/4W,AA,TP,2.4x6.4mm R270 2001-000011 R-CARBON 75KOHM,5%,1/8W,AA,TP,1.8X3.2MM R271 2004-001329 R-METAL 9.1Kohm,1%,1/4W,AA,TP,2.4x6.4m R272 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R273 2001-000109 R-CARBON(S) 470OHM,5%,1/2W,AA,TP,2.4X6.4 R275 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R276 2001-000837 R-CARBON 51KOHM,5%,1/8W,AA,TP,1.8X3.2MM R278 2004-000580 R-METAL 22Kohm,1%,1/4W,AA,TP,2.4x6.4mm R279 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R280 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R281 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R282 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R283 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R285 2004-001198 R-METAL 68Kohm,1%,1/4W,AA,TP,2.4x6.4mm R286 2001-000395 R-CARBON 180KOHM,5%,1/4W,AA,TP,2.4X6.4MM R287 2004-001136 R-METAL 6.8Kohm,1%,1/4W,AA,TP,2.4x6.4m R289 2001-000354 R-CARBON 150KOHM,5%,1/4W,AA,TP,2.4X6.4MM R290 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R291 2001-000007 R-CARBON 3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R292 2001-000812 R-CARBON 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM R293 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R294 2001-000007 R-CARBON 3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R295 2001-000812 R-CARBON 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM R296 2001-000331 R-CARBON 12KOHM,5%,1/8W,AA,TP,1.8X3.2MM R297 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R298 2001-001138 R-CARBON(S) 390OHM,5%,1/2W,AA,TP,2.4X6.4 R299 2001-001107 R-CARBON(S) 220ohm,5%,1/2W,AA,TP,2.4x6.4 R301 2004-000560 R-METAL 220Kohm,1%,1/4W,AA,TP,2.4x6.4m R302 2004-000412 R-METAL 18Kohm,1%,1/4W,AA,TP,2.4x6.4mm R303 2004-001661 R-METAL 3Kohm,1%,1/4W,AA,TP,2.4x6.4mm R304 2004-000716 R-METAL 3.6Kohm,1%,1/4W,AA,TP,2.4x6.4m R305 2004-001254 R-METAL 8.2Kohm,1%,1/4W,AA,TP,2.4x6.4m R306 2005-001064 R-WIREWOUND 0.9OHM,5%,2W,AA,TP,3.8X11MM R307 2001-001088 R-CARBON(S) 1KOHM,5%,1/2W,AA,TP,2.4X6.4M R308 2004-001187 R-METAL 680ohm,1%,1/4W,AA,TP,2.4x6.4mm R309 2001-000016 R-CARBON(S) 1OHM,5%,1/2W,AA,TP,2.4X6.4MM

7 Electrical Parts List

7-10 PG17N*/PG19N*

Loc. No. Code No. Description Specification Remarks

R310 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R311 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R312 2001-000977 R-CARBON 8.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R313 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R314 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R315 2008-000114 R-FUSIBLE 1.2ohm,5%,1/2W,AA,TP,3.5x9.4mm R316 2008-000114 R-FUSIBLE 1.2ohm,5%,1/2W,AA,TP,3.5x9.4mm R320 2004-001298 R-METAL 82Kohm,2%,1/4W,AA,TP,2.4x6.4mm R401 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R402 2003-000514 R-METALOXIDE(S) 15ohm,5%,2W,AA,TP,4x12mm R403 2001-000061 R-CARBON 33OHM,5%,1/4W,AA,TP,2.4X6.4MM R404 2001-000800 R-CARBON 5.1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R409 2001-000110 R-CARBON 10OHM,5%,1/4W,AA,TP,2.4X6.4MM R410 2006-001069 R-CEMENT 2.2OHM,5%,5W,CA,BK,9.5X22X9.5MM R411 2003-000747 R-METALOXIDE(S) 56ohm,5%,3W,AA,TP,6x16mm R412 2003-000747 R-METALOXIDE(S) 56ohm,5%,3W,AA,TP,6x16mm R413 2003-000724 R-METALOXIDE(S) 5.6ohm,5%,3W,AA,TP,6x16m R415 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R416 2001-001163 R-CARBON(S) 560OHM,5%,1/2W,AA,TP,2.4X6.4 R418 2003-000473 R-METALOXIDE(S) 10ohm,5%,3W,AA,TP,6x16mm R419 2001-000019 R-CARBON(S) 10OHM,5%,1/2W,AA,TP,2.4X6.4M R421 2006-001063 R-CEMENT 75OHM,5%,5W,CA,BK,9.5X22X9.5MM R422 2001-000028 R-CARBON(S) 100OHM,5%,1/2W,AA,TP,2.4X6.4 R423 2001-000028 R-CARBON(S) 100OHM,5%,1/2W,AA,TP,2.4X6.4 R430 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R451 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM R452 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM R453 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R454 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R455 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM R456 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R457 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM R458 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R459 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM R460 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R461 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R462 2001-001128 R-CARBON(S) 30KOHM,5%,1/2W,AA,TP,2.4X6.4 R463 2003-000751 R-METALOXIDE(S) 6.8Kohm,5%,1W,AA,TP,3.3x R464 2003-000485 R-METALOXIDE(S) 12Kohm,5%,1W,AA,TP,3.3x9 R465 2001-001108 R-CARBON(S) 22KOHM,5%,1/2W,AA,TP,2.4X6.4 R466 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R467 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R468 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R469 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R470 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R471 2003-000450 R-METALOXIDE(S) 100Kohm,5%,3W,AA,TP,6x16 R476 2001-000022 R-CARBON(S) 33OHM,5%,1/2W,AA,TP,2.4X6.4M

7 Electrical Parts List

PG17N*/PG19N* 7-11

Loc. No. Code No. Description Specification Remarks

R477 2003-000661 R-METALOXIDE(S) 33ohm,5%,2W,AA,TP,4x12mm R480 2008-000140 R-FUSIBLE 2.2ohm,5%,1/2W,AA,TP,3.5x9.4mm R501 2001-000962 R-CARBON 75KOHM,5%,1/4W,AA,TP,2.4X6.4MM R502 2004-000327 R-METAL 150Kohm,1%,1/4W,AA,TP,2.4x6.4m R503 2001-000096 R-CARBON(S) 1MOHM,5%,1/2W,AA,TP,2.4X6.4M R504 2001-000546 R-CARBON 270KOHM,5%,1/4W,AA,TP,2.4X6.4MM R506 2001-000660 R-CARBON 33KOHM,5%,1/8W,AA,TP,1.8X3.2MM R507 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM R508 2001-000563 R-CARBON 27KOHM,5%,1/8W,AA,TP,1.8X3.2MM R509 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM R510 2001-000563 R-CARBON 27KOHM,5%,1/8W,AA,TP,1.8X3.2MM R511 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM R512 2004-000979 R-METAL 47Kohm,1%,1/4W,AA,TP,2.4x6.4mm R513 2004-004232 R-METAL 249Kohm,1%,1/4W,AA,TP,2.5x6.5m R521 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R523 2001-000006 R-CARBON 2.4KOHM,5%,1/8W,AA,TP,1.8X3.2MM R524 2001-000689 R-CARBON 390KOHM,5%,1/8W,AA,TP,1.8X3.2MM R525 2001-000977 R-CARBON 8.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R526 2001-000331 R-CARBON 12KOHM,5%,1/8W,AA,TP,1.8X3.2MM R527 2001-000800 R-CARBON 5.1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R528 2001-000660 R-CARBON 33KOHM,5%,1/8W,AA,TP,1.8X3.2MM R529 2001-000800 R-CARBON 5.1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R530 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R532 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R533 2001-000780 R-CARBON 470OHM,5%,1/8W,AA,TP,1.8X3.2MM R534 2001-000018 R-CARBON 6.8OHM,5%,1/4W,AA,TP,2.4X6.4MM R535 2005-000401 R-WIREWOUND,NON 0.47ohm,5%,2W,AA,TP,4.7 R536 2003-000014 R-METALOXIDE(S) 10Kohm,5%,3W,AA,TP,6x16m R537 2003-000014 R-METALOXIDE(S) 10Kohm,5%,3W,AA,TP,6x16m R538 2001-000073 R-CARBON 33KOHM,5%,1/4W,AA,TP,2.4X6.4MM R539 2006-001066 R-CEMENT 33OHM,5%,7W,CS,BK,9X10X54MM R540 2004-001298 R-METAL 82Kohm,2%,1/4W,AA,TP,2.4x6.4mm R541 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R542 2004-001349 R-METAL 91Kohm,1%,1/4W,AA,TP,2.4x6.4mm R543 2001-000977 R-CARBON 8.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R549 2003-000462 R-METALOXIDE(S) 10Kohm,5%,2W,AA,TP,4x12m R551 2003-000006 R-METALOXIDE 47ohm,5%,1W,AA,TP,4.3x12mm R552 2001-000066 R-CARBON(S) 10KOHM,5%,1/2W,AA,TP,2.4X6.4 R553 2001-001153 R-CARBON(S) 47OHM,5%,1/2W,AA,TP,2.4X6.4M R554 2001-000613 R-CARBON 3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM R555 2001-000319 R-CARBON 120KOHM,5%,1/8W,AA,TP,1.8X3.2MM R556 2001-000045 R-CARBON 1.8KOHM,5%,1/4W,AA,TP,2.4X6.4MM R558 2003-000462 R-METALOXIDE(S) 10Kohm,5%,2W,AA,TP,4x12m R560 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM R561 2001-000613 R-CARBON 3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM R562 2001-000995 R-CARBON 820OHM,5%,1/8W,AA,TP,1.8X3.2MM R563 2001-000114 R-CARBON(S) 180KOHM,5%,1/2W,AA,TP,2.4X6

7 Electrical Parts List

7-12 PG17N*/PG19N*

Loc. No. Code No. Description Specification Remarks

R564 2001-000114 R-CARBON(S) 180KOHM,5%,1/2W,AA,TP,2.4X6 R565 2001-000114 R-CARBON(S) 180KOHM,5%,1/2W,AA,TP,2.4X6 R566 2001-000114 R-CARBON(S) 180KOHM,5%,1/2W,AA,TP,2.4X6 R570 2001-000019 R-CARBON(S) 10OHM,5%,1/2W,AA,TP,2.4X6.4M R601 2001-000354 R-CARBON 150KOHM,5%,1/4W,AA,TP,2.4X6.4MM R603 2001-000044 R-CARBON 1.2KOHM,5%,1/4W,AA,TP,2.4X6.4MM R604 2001-000087 R-CARBON(S) 120KOHM,5%,1/2W,AA,TP,2.4X6 R605 2001-000085 R-CARBON(S) 100KOHM,5%,1/2W,AA,TP,2.4X6 R607 2001-000376 R-CARBON 15OHM,5%,1/8W,AA,TP,1.8X3.2MM R608 2003-000756 R-METALOXIDE(S) 6.8Kohm,5%,3W,AA,TP,6x16 R609 2001-000552 R-CARBON 270OHM,5%,1/4W,AA,TP,2.4X6.4MM R611 2001-000354 R-CARBON 150KOHM,5%,1/4W,AA,TP,2.4X6.4MM R630 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R631 2001-000023 R-CARBON 47OHM,5%,1/4W,AA,TP,2.4X6.4MM R632 2001-000003 R-CARBON 330ohm,5%,1/8W,AA,TP,1.8x3.2mm R634 2001-001131 R-CARBON(S) 33KOHM,5%,1/2W,AA,TP,2.4X6.4 R635 2003-000495 R-METALOXIDE(S) 150Kohm,5%,1W,AA,TP,3.3 R636 2001-001053 R-CARBON(S) 1.5OHM,5%,1/2W,AA,TP,2.4X6.4 R637 2001-000577 R-CARBON 2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R638 2001-000577 R-CARBON 2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R639 2001-000241 R-CARBON 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM R640 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R641 2001-000034 R-CARBON 220OHM,5%,1/4W,AA,TP,2.4X6.4MM R642 2001-000508 R-CARBON 220KOHM,5%,1/8W,AA,TP,1.8X3.2MM R643 2003-000521 R-METALOXIDE(S) 180Kohm,5%,1W,AA,TP,3.3x R644 2001-000890 R-CARBON 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM R645 2004-000679 R-METAL 2Kohm,1%,1/4W,AA,TP,2.4x6.4mm R646 2004-000334 R-METAL 150ohm,1%,1/4W,AA,TP,2.4x6.4mm R648 2003-000495 R-METALOXIDE(S) 150Kohm,5%,1W,AA,TP,3.3 R651 2001-001138 R-CARBON(S) 390OHM,5%,1/2W,AA,TP,2.4X6.4 R657 2001-000495 R-CARBON 20KOHM,5%,1/4W,AA,TP,2.4X6.4MM R661 2001-001050 R-CARBON(S) 1.5KOHM,5%,1/2W,AA,TP,2.4X6 R662 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R663 2001-000515 R-CARBON 220OHM,5%,1/8W,AA,TP,1.8X3.2MM R664 2001-000495 R-CARBON 20KOHM,5%,1/4W,AA,TP,2.4X6.4MM R665 2004-000964 R-METAL 470Kohm,1%,1/4W,AA,TP,2.4x6.4m R666 2004-000964 R-METAL 470Kohm,1%,1/4W,AA,TP,2.4x6.4m R667 2004-001211 R-METAL 7.5Kohm,1%,1/4W,AA,TP,2.4x6.4m R668 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R669 2001-000793 R-CARBON 47OHM,5%,1/8W,AA,TP,1.8X3.2MM RL601 3501-001128 RELAY-POWER 12Vdc,530mW,5A,2FormA,15mS,1 SK521 4715-000001 SURGEABSORBER 1KV,+50-10% SW6 3403-001075 SWITCH-PUSH 30Vdc,300mA,DPDT,OFF-ON-OFF T401 BH26-00041A TRANS-HOR.DRIVE 2.7MH,8P,EI-2519,PL3 T402 BH26-00063A TRANS-HOR.PULSE 1mH/92uH/0.66uH,10P,EI30 T501 BH26-00051A TRANS-FBT 80.4UH,14P,HV22UR,HV22U,FE T502 BH26-00056A TRANS-FOCUS 3.8MHMIN,10P,SB-5S,EI-2218,S

7 Electrical Parts List

PG17N*/PG19N* 7-13

Loc. No. Code No. Description Specification Remarks

T601 BH26-00050A TRANS-POWER 130UH,18P,EER4445,PL3,130UH/ T602 BH26-30302S TRANS-SYNC. 3-1(250UH),SB-5S,UU1116 T661 BH26-00042A TRANS 2.5MH,8P,EI-1916,PL3,150UH TH601 1404-001076 THERMISTOR-NTC 8ohm,15%,17mW/C,TP VR401 2103-001049 VR-SEMI 100ohm,30%,1/5W,SIDE VR501 2103-001080 VR-SEMI 100KOHM,25%,0.3W,SIDE X201 2801-000006 CRYSTAL-UNIT 12MHz,50ppm,28-AAM,S,35ohm ZD242 0403-000007 DIODE-ZENER UZ6.2BM,6.2V,6.0-6.4V,500mW ZD252 0403-000007 DIODE-ZENER UZ6.2BM,6.2V,6.0-6.4V,500mW ZD401 0403-000004 DIODE-ZENER UZ12BM,12V,11.6-12.4V,500mW ZD501 0403-000005 DIODE-ZENER UZ5.1B,4.8-5.4V,500mW,DO-35 ZD601 0403-000753 DIODE-ZENER MTZJ27D,27V,26.29-27.64V,500 ZD602 0403-001068 DIODE-ZENER UZ4.7BSA,4.7V,4.47-4.65V,500 ZD603 0403-001220 DIODE-ZENER UZ2.7BSB,2.69-2.91V,500MW,DO ZD661 0403-000367 DIODE-ZENER UZ7.5BSC,7.5V,7.33-7.64V,500

7 Electrical Parts List

7-14 PG17N*/PG19N*

Loc. No. Code No. Description Specification Remarks

BD101 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 BD105 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 BD106 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 BD151 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 BD155 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 BD181 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 BD182 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 C101 2401-003224 C-AL 470uF,20%,16V,WT,TP,8X11.5,5mm C102 2202-000319 C-CERAMIC,MLC-RADIAL 100nF,10%,100V,X7R C103 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C104 2401-003224 C-AL 470uF,20%,16V,WT,TP,8X11.5,5mm C105 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP C106 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C107 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C108 2401-003224 C-AL 470uF,20%,16V,WT,TP,8X11.5,5mm C109 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C110 2401-003080 C-AL 3.3UF,20%,50V,BP,TP,5X11,2.5 C111 2202-000319 C-CERAMIC,MLC-RADIAL 100nF,10%,100V,X7R C112 2401-003484 C-AL 10uF,20%,100V,LZ,TP,6.3X11,5 C113 2401-000393 C-AL 10uF,20%,100V,WT,TP,8x11.5,5 C114 2401-000393 C-AL 10uF,20%,100V,WT,TP,8x11.5,5 C115 2401-000031 C-AL 47uF,20%,16V,GP,TP,5x11,5 C116 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5 C117 2401-000010 C-AL 220uF,20%,16V,GP,6.3x11mm,2 C118 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C119 2201-000144 C-CERAMIC,DISC 0.1nF,5%,50V,NP0,TP,8.5x3 C120 2201-000247 C-CERAMIC,DISC 0.015nF,5%,50V,NP0,TP,5x3 C124 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C126 2401-000613 C-AL 1uF,20%,50V,WT,TP,5x11,5 C128 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C141 2201-000764 C-CERAMIC,DISC 0.082nF,5%,50V,NP0,TP,8x3 C142 2202-000654 C-CERAMIC,MLC-RADIAL 100nF,10%,50V,X7R,T C151 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5 C152 2202-000669 C-CERAMIC,MLC-RADIAL 10nF,10%,50V,X7R,TP C154 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C155 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5 C156 2401-000010 C-AL 220uF,20%,16V,GP,6.3x11mm,2 C157 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5 C158 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C161 2202-000669 C-CERAMIC,MLC-RADIAL 10nF,10%,50V,X7R,TP C166 2301-000004 C-FILM,PEF 2.2nF,5%,100V,TP,5.5X10X2.9,5 C167 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5 C168 2401-000050 C-AL 10uF,20%,16V,GP,TP,5x11,2.5 C169 2401-000050 C-AL 10uF,20%,16V,GP,TP,5x11,2.5 C171 2201-000234 C-CERAMIC,DISC 0.15nF,5%,50V,NP0,TP,9x3 C172 2201-000234 C-CERAMIC,DISC 0.15nF,5%,50V,NP0,TP,9x3 C181 2201-000288 C-CERAMIC,DISC 1nF,10%,2kV,Y5P,TP,9x5,10

7 Electrical Parts List

PG17N*/PG19N* 7-15

Loc. No. Code No. Description Specification Remarks

7-2 Video PCB Parts

C182_1 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP C183 2201-000530 C-CERAMIC,DISC 4.7nF,10%,500V,Y5P,TP,12 CB01 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 CB02 2202-000319 C-CERAMIC,MLC-RADIAL 100nF,10%,100V,X7R CB11 2201-000273 C-CERAMIC,DISC 0.018nF,5%,50V,NP0,TP,5x3 CB12 2201-000504 C-CERAMIC,DISC 0.039nF,5%,50V,SL,TP,5x3 CB14 2305-000009 C-FILM,MPEF 100nF,5%,250V,TP,13x11x6.5,7 CB16 2401-001318 C-AL 470nF,20%,100V,GP,TP,5x11,5 CB17 2401-001334 C-AL 470nF,20%,50V,GP,TP,5x11,2.5 CB21 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 CBC 2201-002080 C-CERAMIC,DISC 0.027NF,5%,500V,NPO,TP,6 CG01 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 CG02 2401-000031 C-AL 47uF,20%,16V,GP,TP,5x11,5 CG03 2202-000319 C-CERAMIC,MLC-RADIAL 100nF,10%,100V,X7R CG11 2201-000247 C-CERAMIC,DISC 0.015nF,5%,50V,NP0,TP,5x3 CG12 2201-000504 C-CERAMIC,DISC 0.039nF,5%,50V,SL,TP,5x3 CG14 2305-000009 C-FILM,MPEF 100nF,5%,250V,TP,13x11x6.5,7 CG16 2401-001318 C-AL 470nF,20%,100V,GP,TP,5x11,5 CG17 2401-001334 C-AL 470nF,20%,50V,GP,TP,5x11,2.5 CG21 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V CGC 2201-002080 C-CERAMIC,DISC 0.027NF,5%,500V,NPO,TP,6 CGP 2301-000188 C-FILM,PEF 1nF,5%,100V,TP,10.5x12.5x6.5 CIS BH39-00078A CBF-HARNESS 150MM,BLK,UL1015,AWG18,357 CIS BH13-10335P IC-HYBRID S-PROJECT,VPS14,ZIP,15P,CRT/DR CN101 3711-004228 CONNECTOR-HEADER BOX,6P,1R,2MM,ANGLE,SN CN102 3711-004123 CONNECTOR-HEADER BOX,15P,1R,2mm,ANGLE,SN CN12 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN13 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CN14 BH71-40300A PIN-HINGE BRASS,D2.36,SN,HEAT/SINK CR01 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 CR02 2401-000031 C-AL 47uF,20%,16V,GP,TP,5x11,5 CR11 2201-000247 C-CERAMIC,DISC 0.015nF,5%,50V,NP0,TP,5x3 CR12 2201-000504 C-CERAMIC,DISC 0.039nF,5%,50V,SL,TP,5x3 CR14 2305-000009 C-FILM,MPEF 100nF,5%,250V,TP,13x11x6.5,7 CR16 2401-003479 C-AL 0.47UF,20%,100V,WT,TP,5X11MM,5 CR17 2401-003479 C-AL 0.47UF,20%,100V,WT,TP,5X11MM,5 CR21 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 CRC 2201-002080 C-CERAMIC,DISC 0.027NF,5%,500V,NPO,TP,6 CRP 2301-000188 C-FILM,PEF 1nF,5%,100V,TP,10.5x12.5x6.5 D104 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D151 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 DB03 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T DB04 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T DB05 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 DB07 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 DG03 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T DG04 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T

7 Electrical Parts List

7-16 PG17N*/PG19N*

Loc. No. Code No. Description Specification Remarks

DG05 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 DG07 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 DR03 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T DR04 0401-000006 DIODE-SWITCHING BAV21,250V,250mA,DO-35,T DR05 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 DR07 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 EY1 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY2 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH EY5 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH EY6 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH EY8 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH IC101 1201-001287 IC-VIDEOAMP 52748,DIP,36P,500MIL,TRIPLE IC103 BH09-00015A IC-OSDPROCESSOR PEGASUSN/F,KS2501B-14,24 IC104 1201-001242 IC-PREAMP 52324,DIP,18P,DUAL,PLASTIC JP124 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 JP159 3301-000011 CORE-FERRITEBEAD AA,3.5x1.0x5.7mm,1500 L101 2701-000125 INDUCTOR-AXIAL 150uH,10%,3x7mm L102 2701-000125 INDUCTOR-AXIAL 150uH,10%,3x7mm LB03 2701-001069 INDUCTOR-AXIAL 180NH,10%,3X7MM LG03 2701-001069 INDUCTOR-AXIAL 180NH,10%,3X7MM LR03 2701-001065 INDUCTOR-AXIAL 0.22UH,10%,3X7MM MP2.0 BH41-00028A PCB-VIDEO FR1,247*330,1.6T Q101 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP Q102 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP Q104 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP Q141 0501-000122 TR-SMALLSIGNAL 2N3904,NPN,625mW,TO-92,TP QB02 0501-000140 TR-SMALLSIGNAL 2N5551,NPN,625mW,TO-92 QB03 0501-000138 TR-SMALLSIGNAL 2N5401,PNP,625mW,TO-92,TP QB51 0501-000581 TR-SMALLSIGNAL 2N3906,PNP,625mW,TO-92,TP QG02 0501-000140 TR-SMALLSIGNAL 2N5551,NPN,625mW,TO-92 QG03 0501-000138 TR-SMALLSIGNAL 2N5401,PNP,625mW,TO-92,TP QG51 0501-000581 TR-SMALLSIGNAL 2N3906,PNP,625mW,TO-92,TP QR02 0501-000140 TR-SMALLSIGNAL 2N5551,NPN,625mW,TO-92 QR03 0501-000138 TR-SMALLSIGNAL 2N5401,PNP,625mW,TO-92,TP QR51 0501-000581 TR-SMALLSIGNAL 2N3906,PNP,625mW,TO-92,TP R101 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R102 2001-001000 R-CARBON 82KOHM,5%,1/8W,AA,TP,1.8X3.2MM R103 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R110 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R111 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R112 2001-000472 R-CARBON 2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R113 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R114 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM R115 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R117 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R118 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R119 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM

7 Electrical Parts List

PG17N*/PG19N* 7-17

Loc. No. Code No. Description Specification Remarks

R120 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM R124 2001-000857 R-CARBON 560OHM,5%,1/8W,AA,TP,1.8X3.2MM R125 2001-000006 R-CARBON 2.4KOHM,5%,1/8W,AA,TP,1.8X3.2MM R126 2001-000008 R-CARBON 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM R127 2001-000356 R-CARBON 150KOHM,5%,1/8W,AA,TP,1.8X3.2MM R131 2004-000150 R-METAL 1.5Kohm,1%,1/4W,AA,TP,2.4x6.4m R141 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM R142 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R151 2001-000800 R-CARBON 5.1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R152 2001-000633 R-CARBON 30KOHM,5%,1/8W,AA,TP,1.8X3.2MM R153 2001-000325 R-CARBON 120OHM,5%,1/8W,AA,TP,1.8X3.2MM R156 2001-000857 R-CARBON 560OHM,5%,1/8W,AA,TP,1.8X3.2MM R157 2001-000857 R-CARBON 560OHM,5%,1/8W,AA,TP,1.8X3.2MM R158 2001-000878 R-CARBON 6.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R159 2001-000613 R-CARBON 3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM R161 2001-000577 R-CARBON 2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R162 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM R164 2001-000003 R-CARBON 330ohm,5%,1/8W,AA,TP,1.8x3.2mm R165 2001-000613 R-CARBON 3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM R168 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R169 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R171 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R172 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R175 2002-001022 R-COMPOSITION 30MOHM,5%,1/4W,AA,TP,2.5X6 R181 2001-001107 R-CARBON(S) 220ohm,5%,1/2W,AA,TP,2.4x6.4 R183 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM RB02 2001-000527 R-CARBON 22OHM,5%,1/8W,AA,TP,1.8X3.2MM RB04 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM RB05 2001-000780 R-CARBON 470OHM,5%,1/8W,AA,TP,1.8X3.2MM RB06 2001-000666 R-CARBON 33OHM,5%,1/8W,AA,TP,1.8X3.2MM RB11 2001-000793 R-CARBON 47OHM,5%,1/8W,AA,TP,1.8X3.2MM RB12 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM RB14 2001-000482 R-CARBON 200KOHM,5%,1/4W,AA,TP,2.4X6.4MM RB15 2001-000047 R-CARBON 2.2KOHM,5%,1/4W,AA,TP,2.4X6.4MM RB16 2001-000962 R-CARBON 75KOHM,5%,1/4W,AA,TP,2.4X6.4MM RB17 2001-000020 R-CARBON(S) 22OHM,5%,1/2W,AA,TP,2.4X6.4M RB18 2001-000037 R-CARBON(S) 330OHM,5%,1/2W,AA,TP,2.4X6.4 RB21 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM RB26 2001-000003 R-CARBON 330ohm,5%,1/8W,AA,TP,1.8x3.2mm RB31 2001-000110 R-CARBON 10OHM,5%,1/4W,AA,TP,2.4X6.4MM RBR 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM RG02 2001-000527 R-CARBON 22OHM,5%,1/8W,AA,TP,1.8X3.2MM RG04 2001-000356 R-CARBON 150KOHM,5%,1/8W,AA,TP,1.8X3.2MM RG05 2001-000780 R-CARBON 470OHM,5%,1/8W,AA,TP,1.8X3.2MM RG06 2001-000969 R-CARBON 75OHM,5%,1/8W,AA,TP,1.8X3.2MM RG11 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM RG12 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM

7 Electrical Parts List

7-18 PG17N*/PG19N*

Loc. No. Code No. Description Specification Remarks

RG14 2001-000482 R-CARBON 200KOHM,5%,1/4W,AA,TP,2.4X6.4MM RG15 2001-000047 R-CARBON 2.2KOHM,5%,1/4W,AA,TP,2.4X6.4MM RG16 2001-000962 R-CARBON 75KOHM,5%,1/4W,AA,TP,2.4X6.4MM RG17 2001-000020 R-CARBON(S) 22OHM,5%,1/2W,AA,TP,2.4X6.4M RG18 2001-000037 R-CARBON(S) 330OHM,5%,1/2W,AA,TP,2.4X6.4 RG21 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM RG26 2001-000003 R-CARBON 330ohm,5%,1/8W,AA,TP,1.8x3.2mm RG31 2001-000333 R-CARBON 12OHM,5%,1/4W,AA,TP,2.4X6.4MM RGG 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM RGP 2001-000723 R-CARBON 4.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM RR02 2001-000527 R-CARBON 22OHM,5%,1/8W,AA,TP,1.8X3.2MM RR04 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM RR05 2001-000780 R-CARBON 470OHM,5%,1/8W,AA,TP,1.8X3.2MM RR06 2001-000666 R-CARBON 33OHM,5%,1/8W,AA,TP,1.8X3.2MM RR11 2001-000793 R-CARBON 47OHM,5%,1/8W,AA,TP,1.8X3.2MM RR12 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM RR14 2001-000482 R-CARBON 200KOHM,5%,1/4W,AA,TP,2.4X6.4MM RR15 2001-000047 R-CARBON 2.2KOHM,5%,1/4W,AA,TP,2.4X6.4MM RR16 2001-000962 R-CARBON 75KOHM,5%,1/4W,AA,TP,2.4X6.4MM RR17 2001-000020 R-CARBON(S) 22OHM,5%,1/2W,AA,TP,2.4X6.4M RR18 2001-000037 R-CARBON(S) 330OHM,5%,1/2W,AA,TP,2.4X6.4 RR21 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM RR26 2001-000003 R-CARBON 330ohm,5%,1/8W,AA,TP,1.8x3.2mm RR31 2001-000110 R-CARBON 10OHM,5%,1/4W,AA,TP,2.4X6.4MM RRP 2001-000723 R-CARBON 4.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM RRR 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM SK101 4715-000102 SURGEABSORBER 200V,20%,1000A,RADIAL SK102 4715-000102 SURGEABSORBER 200V,20%,1000A,RADIAL SK103 4715-000102 SURGEABSORBER 200V,20%,1000A,RADIAL SK104 4715-000106 SURGEABSORBER 300V,210-390V,AXIAL SK105 3704-001118 SOCKET-CRT 10P,22.5PI,26.5PI,NI SK108 4715-000001 SURGEABSORBER 1KV,+50-10% ZD101 0403-000509 DIODE-ZENER MTZJ5.6B,5.6V,5.45-5.73V,500 ZD102 0403-000509 DIODE-ZENER MTZJ5.6B,5.6V,5.45-5.73V,500

7 Electrical Parts List

PG17N*/PG19N* 7-19

Loc. No. Code No. Description Specification Remarks

C801 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C802 2401-001509 C-AL 47uF,20%,16V,GP,TP,5x7mm,5 C803 2401-001509 C-AL 47uF,20%,16V,GP,TP,5x7mm,5 C804 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C805 2401-003080 C-AL 3.3UF,20%,50V,BP,TP,5X11,2.5 C806 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C807 2401-003080 C-AL 3.3UF,20%,50V,BP,TP,5X11,2.5 C809 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C810 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C811 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C812 2201-000389 C-CERAMIC,DISC 0.022nF,5%,50V,NP0,TP,5x3 C813 2201-000389 C-CERAMIC,DISC 0.022nF,5%,50V,NP0,TP,5x3 C814 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C815 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5 C816 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C817 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C818 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C819 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C820 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C821 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C822 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C823 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C824 2401-000698 C-AL 2200uF,20%,16V,WT,TP,12.5x25,5 C825 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C826 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C827 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V C828 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5 C829 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5 C830 2401-001509 C-AL 47uF,20%,16V,GP,TP,5x7mm,5 C831 2401-001509 C-AL 47uF,20%,16V,GP,TP,5x7mm,5 C832 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C833 2401-003080 C-AL 3.3UF,20%,50V,BP,TP,5X11,2.5 C834 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C835 2401-003080 C-AL 3.3UF,20%,50V,BP,TP,5X11,2.5 C836 2401-001509 C-AL 47uF,20%,16V,GP,TP,5x7mm,5 C837 2401-001509 C-AL 47uF,20%,16V,GP,TP,5x7mm,5 C838 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C839 2401-003080 C-AL 3.3UF,20%,50V,BP,TP,5X11,2.5 C840 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C841 2401-003080 C-AL 3.3UF,20%,50V,BP,TP,5X11,2.5 C842 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C843 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C844 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 C845 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5 CN801 3711-003895 CONNECTOR-HEADER BOX,13P,1R,2mm,STRAIGHT CN802 3711-004386 CONNECTOR-HEADER BOX,3P,1R,2mm,ANGLE,SN CN803 3711-000019 CONNECTOR-HEADER BOX,8P,1R,2.5mm,STRAIGH

7 Electrical Parts List

7-20 PG17N*/PG19N*

Loc. No. Code No. Description Specification Remarks

7-3 Purity PCB Parts

CN804 3711-000821 CONNECTOR-HEADER BOX,2P,1R,2.5mm,STRAIGH CN805 3711-000812 CONNECTOR-HEADER BOX,2P,1R,2.5mm,STRAIGH D801 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 D803 0401-000005 DIODE-SWITCHING 1N4148,100V,200MA,DO-35 IC801 0903-001166 IC-MICROCONTROLLER 88P6232,8BIT,DIP,42P IC801_SOCK 3704-001071 SOCKET-IC 42P,DIP,SN,1.778mm IC802 1201-001199 IC-POWERAMP 6510,SIP,10P,150MIL,DUAL,P IC803 1201-001199 IC-POWERAMP 6510,SIP,10P,150MIL,DUAL,P IC804 1201-001199 IC-POWERAMP 6510,SIP,10P,150MIL,DUAL,P IC805 1201-000420 IC-OPAMP 358,DIP,8P,300MIL,DUAL,100V/mV MP1.0 BH41-00030A P.C.B-SUB SILVER,247*247,1.6T R801 2004-001329 R-METAL 9.1Kohm,1%,1/4W,AA,TP,2.4x6.4m R802 2004-000698 R-METAL 3.3Kohm,1%,1/4W,AA,TP,2.4x6.4m R803 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R804 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R805 2001-000744 R-CARBON 4.7OHM,5%,1/8W,AA,TP,1.8X3.2MM R806 2001-000522 R-CARBON 22KOHM,5%,1/8W,AA,TP,1.8X3.2MM R807 2003-000789 R-METALOXIDE(S) 75ohm,5%,1W,AA,TP,3.3x9m R808 2001-000744 R-CARBON 4.7OHM,5%,1/8W,AA,TP,1.8X3.2MM R809 2001-000522 R-CARBON 22KOHM,5%,1/8W,AA,TP,1.8X3.2MM R810 2003-000744 R-METALOXIDE(S) 56ohm,5%,2W,AA,TP,4x12mm R811 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R812 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R813 2001-000744 R-CARBON 4.7OHM,5%,1/8W,AA,TP,1.8X3.2MM R814 2001-000522 R-CARBON 22KOHM,5%,1/8W,AA,TP,1.8X3.2MM R815 2003-000587 R-METALOXIDE(S) 22ohm,5%,1W,AA,TP,3.3x9m R816 2001-000744 R-CARBON 4.7OHM,5%,1/8W,AA,TP,1.8X3.2MM R817 2001-000522 R-CARBON 22KOHM,5%,1/8W,AA,TP,1.8X3.2MM R818 2003-000587 R-METALOXIDE(S) 22ohm,5%,1W,AA,TP,3.3x9m R819 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R820 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R821 2001-000744 R-CARBON 4.7OHM,5%,1/8W,AA,TP,1.8X3.2MM R822 2001-000522 R-CARBON 22KOHM,5%,1/8W,AA,TP,1.8X3.2MM R823 2003-000587 R-METALOXIDE(S) 22ohm,5%,1W,AA,TP,3.3x9m R824 2001-000744 R-CARBON 4.7OHM,5%,1/8W,AA,TP,1.8X3.2MM R825 2001-000522 R-CARBON 22KOHM,5%,1/8W,AA,TP,1.8X3.2MM R826 2003-000587 R-METALOXIDE(S) 22ohm,5%,1W,AA,TP,3.3x9m R827 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R828 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R829 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R830 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R831 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R832 2004-000441 R-METAL 1Mohm,1%,1/8W,AA,TP,1.8x3.2mm R833 2004-000193 R-METAL 100Kohm,1%,1/4W,AA,TP,2.4x6.4m R834 2004-000216 R-METAL 10Kohm,1%,1/4W,AA,TP,2.4x6.4mm R835 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM R836 2004-000216 R-METAL 10Kohm,1%,1/4W,AA,TP,2.4x6.4mm

7 Electrical Parts List

PG17N*/PG19N* 7-21

Loc. No. Code No. Description Specification Remarks

R837 2004-000979 R-METAL 47Kohm,1%,1/4W,AA,TP,2.4x6.4mm R838 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R839 2004-000580 R-METAL 22Kohm,1%,1/4W,AA,TP,2.4x6.4mm R840 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R841 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R842 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R843 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R844 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R845 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM R846 2001-000244 R-CARBON 1.5MOHM,5%,1/8W,AA,TP,1.8X3.2MM R847 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM R849 2001-000244 R-CARBON 1.5MOHM,5%,1/8W,AA,TP,1.8X3.2MM R850 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM R851 2001-000047 R-CARBON 2.2KOHM,5%,1/4W,AA,TP,2.4X6.4MM TH801 1404-001039 THERMISTOR-NTC 10Kohm,1%,3435K,2.1mW/C,B X801 2801-000006 CRYSTAL-UNIT 12MHz,50ppm,28-AAM,S,35ohm ZD801 0403-000509 DIODE-ZENER MTZJ5.6B,5.6V,5.45-5.73V,500

7 Electrical Parts List

7-22 PG17N*/PG19N*

Loc. No. Code No. Description Specification Remarks

7 Electrical Parts List

PG17N*/PG19N* 7-23

17”,19” Different Parts List

PG17N* PG19N*

code spec code spec

C204 2201-000798 CE,10PF,50V 2201-000389 CE,22PF,50V C205 NONE - 2201-000798 CE,10PF,50V C229 2201-000798 CE,10PF,50V NONE C309 2301-000317 PEF,82NF,100V 2301-000294 PEF,56NF,100V C310 2301-000013 C-FILM,4.7NF,100V 2301-000287 CAP-FILM,5.6NF,100V C418 2301-000519 POLY,100V,3.3NF 2301-000102 POLY,100V,1.2NF C451 2306-000127 C-MPPF,120NF,400V 2301-001259 C-MPPF,100NF,400V C452 2306-000133 C-MPPF,120NF,400V 2301-001259 C-MPPF,100NF,400V C453 2306-000179 MPPF,300NF,250V 2306-000179 C-MPPF,300NF,250V C454 2306-000234 C-MPPF,560NF,250V BH39-40308U JUMPER WIRE C456 2306-000119 MPPF,100NF,250V 2306-000131 C-MPPF,150NF,250V C457 2306-000119 MPPF,100NF,250V 2301-001249 C-MPPF,68NF,400V C609 2401-003483 CAP-AL,270UF,400V BH39-40307U JUMPER WIRE C637 NONE - 2401-000142 C-AL,1000UF,16V C646 NONE - 2401-003486 C-AL,680UF,16V,105`C CIS NONE - BH39-40318U JUMPER WIRE CIS BH39-00066A HARNESS,4P-3P,3P BH39-40319U JUMPER WIRE CN202 NONE - BH39-40317U JUMPER WIRE CN409 3711-000782 WAFER,3P,2.0mm BH39-40314U JUMPER WIRE CN605 NONE - BH39-40315U JUMPER WIRE CN607 NONE - BH39-40316U JUMPER WIRE D631 NONE - 0402-001118 DIODE,UF1G D640 NONE - 0402-001190 DIODE,RG10Z HS602 NONE - BH39-40306U JUMPER WIRE JP269 NONE - BH39-40305U JUMPER WIRE JP305 NONE - BH39-40305U JUMPER WIRE JP317 BH39-40305U JUMPER NONE JP318 2001-001163 CA,1/2W,560OHM BH39-40305U JUMPER WIRE JP38 NONE - BH39-40305U JUMPER WIRE L403 BH26-00065A LINEARITY COIL BH39-40310U JUMPER WIRE PCB NONE - BH39-40320U JUMPER WIRE R221 NONE - 2001-000281 CA,100OHM,1/8W R229 2001-000591 CA,3.3K,1/8W 2001-000977 CA,8.2K,1/8W R285 2004-001298 MF,1/4W,82kohm 2004-001198 MF,1/4W,68 kOHM R286 2004-000398 MF,1/4W,180kohm 2001-000395 CA,1/4W,180kohm R302 2004-000344 R-MF,15KOHM 2004-000412 R-MF,18KOHM R303 2004-000648 R-MF,270 OHM 2004-001661 R-MF,3KOHM R308 2004-000790 MF,1/4W,330 OHM 2004-001187 MF,1/4W,680 OHM R320 2004-000284 R-MF,12KOHM 2004-001298 R-MF,82KOHM R411 2003-002142 R-MO,3W,62OHM BH39-40311U JUMPER WIRE R412 2003-002142 R-MO,3W,62OHM BH39-40312U JUMPER WIRE R413 2003-000473 R-MO,3W,10OHM BH39-40313U JUMPER WIRE R462 2001-000273 CA,1/8W,100KOHM 2001-0001128 CA,1/2W(S),30KOHM R464 2003-000507 MO,1W(S),15KOHM 2003-000485 MO,1W(S),12KOHM R535 2005-001010 MO,1W,0.68ohm 2005-000401 MO,2W,0.47ohm R632 BH39-40305U JUMPER 2001-000003 CA,1/4W,330ohm R633 2001-000591 CA,1/8W,3.3KOHM NONE T601 BH26-00039A SWITCHING TRAINS BH39-40309U JUMPER WIRE

LOCATION

7 Electrical Parts List

7-24 PG17N*/PG19N*

Basic / OEM Different Parts List

BASIC OEM

code spec code spec

BD262 3301-000011 BEAD NONE - Main BNC - BNC-ASS'Y NONE - BNC C667 NONE - 2202-002009 CE,50V,100NF Main CIS NONE - BH39-00070A S-CABLE Main CIS BH39-00058A RGB HARNESS NONE - BNC CN142 NONE - BH41-00036A PCB (SOG)-> 17’ only Video CN201 3711-004379 SMW200-04 NONE - Main CN203 3711-004351 WAFER, 16P, S/T NONE - Main CN205 BH71-40300A PIN-HINGE BH71-40300A PIN-HINGE Main CN206 BH71-40300A PIN-HINGE NONE - Main CN208 NONE - 3711-003843 SMW200-08 Main JP309 BH39-40305U JUMPER WIRE NONE - Main SW1 NONE - 3404-000244 TACT/SW Main SW2 NONE - 3404-000244 TACT/SW Main SW3 NONE - 3404-000244 TACT/SW Main SW4 NONE - 3404-000244 TACT/SW Main SW5 NONE - NONE - Main SW7 NONE - 3404-001079 2, SW Main ZD245 NONE - 0403-000007 ZENER,6.2v Main ZD246 NONE - 0403-000007 ZENER,6.2v Main ZD247 NONE - 0403-000007 ZENER,6.2v Main ZD248 NONE - 0403-000007 ZENER,6.2v Main ZD249 NONE - 0403-000007 ZENER,6.2v Main ZD250 NONE - 0403-000007 ZENER,6.2v Main

LOCATIONLOCATION

PCB Loc.

8 Block Diagram

PG17N*/PG19N* 8-1

VIDEO

OUTPUT

VPS14

BNC/D-SUB

SELECT IC

KA2507

COLOR ADJUST

CONTROL(JIG)

COLOR GAIN CONTROL

VIDEO

CUTOFF

CONTROL

HORIZONTAL

BLANK

M52324P

HORIZONTAL

BLANK

AC INLET SOCKET

LINE FILTER

RECTIFIER

D3SBA60

AC INPUT

90-264VAC

60/50Hz

DEGAUSS

OPERATION

D-COIL

SWITCHING

TRANS

+25V

+14V

+7V

-14V

-14V_I

+80V

+210V

H-DRIVE

CRT HEATER

VERT OUT

SUSPEND

+14V_I

DEGAUSS

24LC081

EEPROM

(SDA/SCL)

S-RASTER

H-SYNC/

V-SYNC

OUT

SDA/SCL

CRYSTAL

12MHz

R G B

CRT

R G B

MICROPROCESSOR

KSC88C6232N

D D C

CONTROL

24LC21A

S-CORRECTION

LED

VIDEO PRE-AMP

M52748

OSD

KS2501

SDA/SCL

ERROR

DETECT

& FEED BACK

POWER SYNC

H-SYNC

TRIGGER

PWM CONTROL &

SWITCHING FET

DP308

BNC/D-SUB

R.G.B

H-SYNC

V-SYNC

INPUT

H-SYNC

V-SYNC

POWER OFF

CONTROL

VIDEO OUTPUT

VOLTAGE

REGULATOR

KA78R12

VOLTAGE

REGULATOR

KA7805

+5V

SOG

HOR.VER. OSC

PROCESSING

TDA4859

H/V DRIVE

DYNAMIC

FOCUS

HORIZONTAL

FOCUS CIRCUIT

H-AFC

HOR. OUTPUT

2SC5584

H-DY

HORIZONTAL

REGULATION

CONTROL

IRF9634

REGULATION

SENSER

HOR. DRIVE

S-CORRECTION

FBT

H/V OUTPUT

2SK2671

H/V REGULATION

ERROR

FEEDBACK

X-RAY

PROTECTOR

VERTICAL BLANKING

GENERATOR

VERTICAL OUTPUT

KA2142

V-DY

VERTICAL FOCUS

CIRCUIT

+12V

HIGH VOLTAGE

SCREEN

FOCUS1, 2

H_LIN.

MOIRE

TILT

CLAMP

ACL

CONTROL BUTTON

OSD CALL/ENTER

POSITION/SIZE

PIN/TRAP

PARALLEL/ROTATION

CHOOSE OR ADJUST

MENU BUTTON

POWER BUTTON

CONTRAST

BRIGHTNESS

H-FLB

V-FLB

SELECT

ACL

CLAMP

DDC-DATA

DDC-CLK

H-LIN

MUTE

DDC-DATA

DDC-CLK

SELECT

SOG

RESET

Temp Sensor

Beam

Time

KSC88C6232N

SDA/SCL

CRYSTAL

12 MHz

CURRENT

AMP

LA6510

TL COIL

TR COIL

BL COIL

BR COIL

H - C/G

V- C/G

SUB POWER

TNY254P

START UP

+7:5V

Purity

Memo

8 Block Diagrams

8-2 PG17N*/PG19N*

9 Wiring Diagram

PG17N*/PG19N* 9-1

9 Wiring Diagram

CN102

GND 1

+5V 2 +12V 3 +80V 4

+7V 5

-14V 6 G1 7

GND 8

AFC 9

V_BLK 10

CLAMP 11

SCL 12 SDA 13 ACL 14 SOG 15

CN204

GND1 +5V2 +12V3 +80V4 +7V5

-14V6 G17 GND8 H_FIB9 B_BLK10 CLAMP11 SCL12 SDA13 ABL14 SOU_OUT15

GND 1

23456

BLUE

GND

GREEN

GND

RED

CN101

GND

12345

BLUE

GND

GREEN

GND

RED

Video PCB

Main PCB

BNC PCB

Purity PCB

GND

+12V

+5V

-14V

SELECTOR

SOG_OUT

GND

GND (NC)

GND

+5V_DDC

H_Sync

V_Sync

DDC_CLK

DDC_DATA

S_RASTER

GND

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15

GND +12V +5V

-14V BNC_DSUB SOG_OUT GND GND (NC) GND DDC 5V H_Sync V_Sync DDC_CLK DDC_DATA S_RASTER GND

CN208

CN102

TL – TL + BL – BL + TR – TR + BR – BR +

1 2 3 4 5 6 7 8

H_CG H_CG

V_CG V_CG

1 2

1BEAM

2GND

3TEMP

4GND

5+5V

6RESET2

7SDA

8SCL

9GND

+14V_I

+14V

GND

+5V

+5V GND

TEMP

1 2

+14V_I +14V GND +5V

1 2 3 4

GND

SDA SCL

RESER2

1 2 3 4

CN202

CN607

CN605

ABL GND

1 2

Temp.Senser

Purity Coil

CRT

TILT CN409

10-1 PG17N*/PG19N*

10 Schematic Diagrams

10-1 Power Part Schematic Diagram

WAVEFORMS

368 V (IC601, #1)

CH1 P-P = 368 V CH1 RMS = 154.6 V

368 V (IC601, #1)

CH1 P-P = 368 V CH1 RMS = 154.6 V

10 Schematic Diagrams

PG17N*/PG19N* 10-2

S-CORRECTION

H-FREQUENCY S1 S2 S3 S4 S5

~ 32.9 kHz H H H H H

HL H HH HH H LH HH H LL HL LHH

LL LHL HH L LH HL L LH HH L LL HH L LL HH L LL HH L LL

LH L LL HL L LL HL L LL

LL L LL

33.0 kHz ~ 34.9 kHz

35.0 kHz ~ 36.9 kHz

37.0 kHz ~ 39.9 kHz

40.0 kHz ~ 45.9 kHz

46.0 kHz ~ 50.9 kHz

51.0 kHz ~ 54.9 kHz

55.0 kHz ~ 60.9 kHz

61.0 kHz ~ 64.9 kHz

65.0 kHz ~ 67.9 kHz

68.0 kHz ~ 69.9 kHz

70.0 kHz ~ 75.9 kHz

76.0 kHz ~ 77.9 kHz

78.0 kHz ~ 80.9 kHz

81.0 kHz ~ 84.9 kHz

85.0 kHz ~ 91.9 kHz

92.0 kHz ~ 94.9 kHz

95.0 kHz ~ 99.9 kHz

100.0 kHz ~ 112.9 kHz

H-FREQUENCY S1 S2 S3 S4 S5

~ 32.9 kHz H H H H H

HH H HH

LL H LH LH H LH LH L HH

HL LHL

LL LHL HH L LH HL L LH

LL L LH

LL L LH HH L LL

LH L LL

LH L LL HL L LL HL L LL

LL L LL

33.0 kHz ~ 34.9 kHz

35.0 kHz ~ 36.9 kHz

37.0 kHz ~ 39.9 kHz

40.0 kHz ~ 45.9 kHz

46.0 kHz ~ 50.9 kHz

51.0 kHz ~ 56.9 kHz

57.0 kHz ~ 60.9 kHz

61.0 kHz ~ 64.9 kHz

65.0 kHz ~ 67.9 kHz

68.0 kHz ~ 71.9 kHz

72.0 kHz ~ 75.9 kHz

76.0 kHz ~ 77.9 kHz

78.0 kHz ~ 80.9 kHz

81.0 kHz ~ 84.9 kHz

85.0 kHz ~ 91.9 kHz

92.0 kHz ~ 94.9 kHz

95.0 kHz ~ 99.9 kHz

100.0 kHz ~ 112.9 kHz

17” 19”

10 Schematic Diagrams

10-3 PG17N*/PG19N*

10-2 Micom Part Schematic Diagram

10 Schematic Diagrams

PG17N*/PG19N* 10-4

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18 19 20 21

22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

0 0 0 0 0 0 0 0

4.72 0

4.79

GND

1.41

1.93

GND

3.75

3.68

4.8

3.24

3.28

3.49

3.38 0

3.61

3.92 0

1.71

3.8

4.2

4.53

4.78

GND

4.26

4.74

4.26 0 0 0 0

4.74

4.8

4.77 0

4.06

4.05

4.03

4.05 0 0 0 0

4.78

GND

1.42

1.93

GND

2.74

4.27

4.78

4.8

2.69

3.42

3.01

3.24 0

3.46

3.15

0.72

1.32

0.38

0.39

1.3

4.72

GND

4.78

4.79

4.78 0 0 0 0

4.73

4.74

4.77 0 0

4.05

4.03

4.05

4.06 0

4.7 0

4.78 GND

1.41

1.94 GND

2.8

4.27

4.79

2.96

3.45

2.8

3.24 0

3.4

2.93

0.82

1.52

0.64

0.36

1.49

4.74

GND

4.77

4.78

4.77 0 0 0 0

4.78

4.74

pin #

MODES MODES

31 kHz 31 kHz68 kHz 68 kHz91 kHz 91 kHz

Table 10-1. IC201 (KSC88C6232N)

Unit: Vrms

5.76 V (IC201, #28)

CH1 P-P = 5.76 V CH1 RMS = 1.844 V

5.44 V (IC201, #29)

CH1 P-P = 5.44 V CH1 RMS = 348 mV

5.60 V (IC201, #27)

CH1 P-P = 5.60 V CH1 RMS =708mV

24.4 V (IC201, #13)

CH1 P-P = 24.4 V CH1 RMS = 6.32 V

10 Schematic Diagrams

10-5 PG17N*/PG19N*

10-3 H/V Process Part Schematic Diagram

10 Schematic Diagrams

PG17N*/PG19N* 10-6

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

1.3 0

3.4

1.33

2.3

10.48 GND

8.34

3.03

1.31

4.03

0.36

1.76

0.78

0.23

4.6

4.73 NC NC

3.02

2.84

2.75

GND

3.74

2.34

2.35

4.38

4.71 NC

5.89

1.92 0

3.37

1.82

2.31

9.31

GND

8.75

10.76

3.02

1.3

5.77

0.99

1.32

1.1

0.25

4.7

4.7 NC NC

2.52

2.84

2.55 GND

3.12

1.76

2.36

4.4

4.98 NC

5.83

2.21 0

3.39

1.92

2.28

7.7

GND

8.35

11.63

3.02

1.3

5.77

0.34

1.51

1.26

0.24

4.69

4.7 NC NC

2.52

2.84

2.66

GND

2.71

1.61

2.36

4.49

5.17 NC

6.07

pin #

MODES MODES

31 kHz 31 kHz68 kHz 68 kHz91 kHz 91 kHz

Table 10-2. IC251 (TDA4859)

Unit: Vrms

1 2 3 4 5 6 7 8 9

11 12 13 14 15 16 17 18 19 20

GND

NC NC NC NC

2.36

5.55

5.85

5.82

10.52

2.43

3.6

0.96

6.67

2.86

0.53

3.68 GND

5.73 NC

GND

NC NC NC NC

2.38

5.56

5.81

5.75

11.89

2.55

3.75

1.21

6.73

1.93

0.42 4

GND

5.74

GND

NC NC NC NC

2.29

5.67

5.82

5.75

11.9

2.57

3.81

0.98

6.72

2.04

0.47

3.81

GND

5.73 NC

pin #

MODES MODES

31 kHz 31 kHz68 kHz 68 kHz91 kHz 91 kHz

Table 10-2. IC250 (M52759SP)

Unit: Vrms

24.4 V (IC261, #1)

CH1 P-P = 24.4 V CH1 RMS = 6.32 V

960 mV (IC261, #32)

CH1 P-P = 960 mV CH1 RMS = 6.042 V

1.32 V (IC261, #12)

CH1 P-P = 1.32V CH1 RMS =1.507 V

13.6 V (IC261, #6)

CH1 P-P = 13.6 V CH1 RMS =9.02 V

13.0 V (H_DRIVE (IC261))

CH1 P-P = 13.0 V CH1 RMS = 7.91V

10 Schematic Diagrams

10-7 PG17N*/PG19N*

10-4 HORI & VERTICAL Part Schematic Diagram

L403

10 Schematic Diagrams

PG17N*/PG19N* 10-8

1 2 3 4 5 6 7 8 9

1.01

13.69 NC

14.78

GND

7.24 NC NC

12.62

0.84

1.01

13.4 NC

14.8

GND

7.64 NC NC

13.08

0.83

1.01

13.59 NC

14.78

GND

7.6 NC NC

13.16

0.83

pin #

MODES

31 kHz 68 kHz 91 kHz

Table 10-3. IC301 (KA2142)

Unit: Vrms

1 2 3 4 5 6 7 8

9 10 11 12

11.93 12

11.54

2.36

2.35 GND

4.34

4.29 GND

4.35

4.32 GND

11.93

9.72

1.72

2.33 GND

3.61

4.97 GND

4.33

4.31 GND

11.96

11.93

8.81

1.49

2.29 GND

3.35

5.23 GND

4.33

4.31 GND

pin #

MODES

31 kHz 68 kHz 91 kHz

Table 10-5. IC403 (AN5452)

Unit: Vrms

31.6 V (V_BLK (IC301))

CH1 P-P = 31.6 V CH1 RMS =12.78 V

55.2 V (IC301, #6)

CH1 P-P = 55.2 V CH1 RMS = 8.04 V

232 V (T402, #6)

CH1 P-P = 232 V CH1 RMS = 141.2 V

66.4 V (Q404, Drain)

CH1 P-P = 66.4V CH1 RMS = 25.84 V

1.24 V (Q405, Collector)

CH1 P-P = 1.24V CH1 RMS = 302 V

28.0 V (T402, #8)

CH1 P-P = 28.0 V CH1 RMS = 5.92 V

10 Schematic Diagrams

10-9 PG17N*/PG19N*

10-5 HIGH VOLTAGE Parts Schematic Diagram

10 Schematic Diagrams

PG17N*/PG19N* 10-10

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16

4.7

4.66

1.71

0.14

0.99

3.15 GND

11.88

4.65

11.83

11.83 GND

4.69

4.67

1.49

0.14

0.59

3.15 GND

11.85

5.48

5.51

11.83

11.83 GND

4.72

4.66

1.14

0.14

0.61

3.15 GND

11.85

6.35

6.3

11.85

11.85 GND

4.7 9

4.7

pin #

MODES

31 kHz 68 kHz 91 kHz

Table 10-6. IC501 (TL494CN)

Unit: Vrms

12.2 V (Q524, Gate)

CH1 P-P = 12.2 V CH1 RMS = 5.30 V

3.52 V (Q551, Emitter)

CH1 P-P =3.52V CH1 RMS = 3.204 V

880 V (T501 #13)

CH1 P-P = 880 V CH1 RMS = 291 V

384 V (Q524, Drain)

CH1 P-P = 384 V CH1 RMS = 198.6 V

10 Schematic Diagrams

10-11 PG17N*/PG19N*

10-6 Video Parts Schematic Diagram (17”)

10 Schematic Diagrams

PG17N*/PG19N* 10-12

10-7 Video Parts Schematic Diagram (19”)

C119

50V

100PF

1N4148

DG01

RG03 820 1/8W

CG04 1uF 50V

R121 R122 1/8W

4.7K

2N3904

Q103

1/8W

DB02 1N4148

DB01 1N4148

DR02 1N4148

DG02 1N4148

1N4148

DR01

RB01 1/8W

R116 1K 1/6W

1/8W

RG01

75 1/8W

RR01

50V

100nF

C170

R170 1/8W

10 Schematic Diagrams

10-13 PG17N*/PG19N*

1 2 3 4 5 6 7 8

9 10 11 12

13 14 15 16 17 18 19 20 21 22 23 24

1.54

1.19

4.72

1.68

4.68

4.67 NC NC NC NC

3.97

3.33

3.44

2.57

0.74 GND

0 0 0 0

3.98

1.64

1.19

4.7

1.69

4.7

4.7 NC NC NC NC

3.9

3.28

3.38

2.47

0.84

GND

0 0 0 0

3.91

2.13

1.19

4.69

2.01

4.7

4.69 NC NC NC NC

3.87

3.2

3.31

2.38

0.88

GND

0 0 0 0

3.87

pin #

MODES MODES

31 kHz 31 kHz68 kHz 68 kHz91 kHz 91 kHz

Table 10-9. IC103 (KS2501)

Unit: Vrms

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18

19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

2.7

11.83 0

GND

2.75

2.31

11.82 0

GND

2.82

11.82 0

GND

3.61

6.18

4.73 0

0.72

4.7

4.74 GND

1.12

2.1

1.95

2.18

1.21

4.48

2.85

1.38

4.2

3.06 GND

3.2

11.22

2.66

11.82 0

GND

2.66

2.29

11.82 0

GND

2.68

11.81 0

GND

3.65

6.19

4.71 0

0.68

4.76

4.69

GND

1.12

1.98

2.14

2.37

1.72

4.45

3.12

1.38

4.18

3.13

GND

3.2

11.2

2.66

11.82 0

GND

2.68

2.28

11.84 0

GND

2.68

11.83 0

GND

3.62

6.2

4.69 0

0.86

4.77

4.72

GND

1.12

2.29

2.14

2.37

2.07

4.44

3.01

1.38

4.16

3.08

GND

3.12

11.26

pin #

MODES MODES

31 kHz 31 kHz68 kHz 68 kHz91 kHz 91 kHz

Table 10-7. IC101 (M52748ASP)

Unit: Vrms

1.08 V (IC101, #2)

CH1 P-P = 1.08 V CH1 RMS = 2.930 V

3.52 V (IC101, #35)

CH1 P-P = 3.52 V CH1 RMS = 3.204 V

5.60 V (IC101, #20)

CH1 P-P = 5.60 V CH1 RMS = 4.964 V

5.76 V (IC101, #21)

CH1 P-P = 5.76 V CH1 RMS = 4.972 V

46.4 V (IC102, #6)

CH1 P-P = 46.4 V CH1 RMS = 47.84 V

6.72 V (IC103, #17)

CH1 P-P = 6.72 V CH1 RMS = 764 mV

4.48 V (IC103, #16)

CH1 P-P = 4.48 V CH1 RMS = 2.652 V

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15

11.82

2.94

2.29

46.5

GND

46.4

2.4

3.02

11.8

GND

11.82

3.2

2.44

45.92

80.1

11.82

2.94

2.32

47.4 GND

47.1

2.36

3.09

11.8 GND

11.82

3.03

2.51

46.8

80.3

11.82

2.98

2.28

47.8

GND

49.2

2.33

2.94

11.8

GND

11.82

3.06

2.41

47.48

80.1

pin #

MODES

31 kHz 68 kHz 91 kHz

Table 10-8. IC102 (VPS14)

Unit: Vrms

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18

1.1 1

1.88

1.1 1

1.74

1.1 1

1.95

10.73

10.73 GND GND

2.71

4.53

11.82

1.1

1.08

2.27

1.1

1.08

2.14

1.1

1.08

2.11

10.8

10.8 GND GND

2.72

4.53

11.82

1.1

1.08

2.27

1.1

1.08

2.14

1.1

1.08

2.12

10.77

10.77 GND GND

2.72

4.54

11.82

pin #

MODES

31 kHz 68 kHz 91 kHz

Table 10-8. IC102 (VPS14)

Unit: Vrms

10 Schematic Diagrams

PG17N*/PG19N* 10-14

10-8 Connector & Option Boards Parts Schematic Diagram

C227

slcon4p

CN142

OP1

SW7

SW4

SW5

SW3

SW2

SW1

CN201

R299

R292

R296

R295

R291

R293

R294

R290

CN203

CN208

10 Schematic Diagrams

10-15 PG17N*/PG19N*

1 2 3 4 5 6 7 8

9 10 11 12

13 14 15 16 17 18 19 20 21 22 23 24

3.25 GND

3.25

4.12

4.35 0

GND

0 0

4.32

3.97

1.75

3.55

4.2

3.09

1.75

4.74

1.75 0

3.23 GND

3.23

1.21

0.37 0

GND

0 0

0.32

1.15

1.74

3.36

4.17

3.03

1.74

4.72

1.74 0

3.22 GND

3.22

1.45

0.34 0

GND

0 0

0.29

1.32

1.73

3.37

4.71

3.03

1.73

4.72

1.73 0

pin #

MODES MODES

31 kHz 31 kHz68 kHz 68 kHz91 kHz 91 kHz

Table 10-7. IC1 (KA2507)

1 2 3 4 5 6 7 8

9 10 11 12 13 14

3.9

1.95

1.96

4.22 0 0

GND

4.21

0.37

4.32

4.73

0.37

4.74

1.08

4.6

1.4 0 0

GND

4.19

4.7

0.32

0.39

4.71

4.74

1.38

4.49

1.56 0 0

GND

4.16

4.7

0.28

0.35

4.7

4.74

pin #

MODES

31 kHz 68 kHz 91 kHz

Table 10-8. IC3 (74HCT14E)

Unit: Vrms

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18 19 20 21

22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

NC NC NC NC NC NC NC NC NC NC

4.8

GND

1.8

1.71 NC

4.7

4.74

4.78 NC

3.32

3.75

3.33

2.93

3.42

3.36 NC NC NC NC NC NC

GND

4.8 NC

3.13

4.63

2.44 NC NC NC NC

NC NC NC NC NC NC NC NC NC NC

4.8

GND

1.75

1.61 NC

4.73

4.72

4.78 NC

3.32

3.75

3.33

2.93

3.42

3.36 NC NC NC NC NC NC GND

4.8 NC

3.13

4.5

2.44 NC NC NC NC

NC NC NC NC NC NC NC NC NC NC

4.8

GND

1.7

1.77 NC

4.72

4.76 NC

3.32

3.75

3.33

2.93

3.42

3.36 NC NC NC NC NC NC

GND

4.8 NC

3.13

4.42

2.44 NC NC NC NC

pin #

MODES MODES

31 kHz 31 kHz68 kHz 68 kHz91 kHz 91 kHz

Table 10-1. IC801 (88P6232)

Unit: Vrms

1 2 3 4 5 6 7 8 9

0.1

0.12

1.33

14.56

1.33

1.3 0 0

13.9

0.1

1.33

1.32

14.56

1.32

1.32 0 0

13.9

0.1

1.32

14.56

1.32

1.31 0 0

13.9

pin #

MODES

31 kHz 68 kHz 91 kHz

Table 10-8. IC802 (LA6510)

Unit: Vrms

1 2 3 4 5 6 7 8 9

4.04

4.26

1.14

1.32

14.56

1.32

0.16

0.12

13.8

4.04

4.26

1.14

1.32

14.56

1.32

0.16

0.12

13.8

4.04

4.26

1.14

1.32

14.56

1.32

0.16

0.12

13.8

pin #

MODES

31 kHz 68 kHz 91 kHz

Table 10-8. IC803 (LA6510)

Unit: Vrms

1 2 3 4 5 6 7 8 9

1.49

1.55

1.32

14.5

1.32

0.74

0.69

13.8

1.51

1.54

1.32

14.56

1.32

0.73

0.7

13.8

1.52

1.55

1.32

14.56

1.32

0.73

0.69

13.8

pin #

MODES

31 kHz 68 kHz 91 kHz

Table 10-8. IC804 (LA6510)

Unit: Vrms

10 Schematic Diagrams

PG17N*/PG19N* 10-16

10-9 PURITY Parts Schematic Diagram

6.56 V (IC801 #21)

CH1 P-P = 6.56 V CH1 RMS = 3.372 V

6.32 V (IC801 #20)

CH1 P-P = 6.32 V CH1 RMS = 3.376 V

229

230

Memo

10 Schematic Diagrams

10-17 PG17N*/PG19N*

Samsung PG19N, PG17N Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual