Samsung PDP-MONITOR User Manual

Download

PDP-MONITOR (PLASMA

DISPLAY PANEL)

Owner’s Instructions

Before operating the unit,

please read this manual thoroughly,

and retain it for future reference.

ON-SCREEN MENUS

Energy Saving

SRS TruSurroundXT

Digital Natural Image engine

This device is a Class A digital apparatus.

User Instructions

◆ Screen Image retention

Do not display a still image (such as on a video game or when hooking up a PC to this PDP Monitor) on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.

◆ Height

The PDP Monitor can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height so do not install and operate there.

◆ Heat on the top of the PDP Monitor

The top side of the product may be hot after long periods of use as heat dissipates from the panel through the vent hole in the upper part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be prevented from touching the upper part of the product.

◆ The product is making a ‘cracking’ noise.

A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as temperature or humidity. This is normal and not a defect of the unit.

◆ Cell Defects

The PDP Monitor uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require sophisticated technology to produce. However, there may be few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product.

◆ Avoid operating the PDP Monitor at temperatures below 5°C(41°F)

◆ A still image displayed too long may cause permanent damage to the PDP Monitor Panel.

◆ Afterimage on the Screen.

Displaying still images from Video games and PC for longer than a certain period of time may produce partial afterimages. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.

◆ Warranty

- Warranty does not cover any damage caused by image retention.

- Burn-in is not covered by the warranty.

◆ Installation

Be sure to contact an authorized service centre, when installing your set in a location with heavy dust, high or low temperatures, high humidity, chemical substance and where it operates continually such as the airport, the train station etc. Failure to do so may cause a serious damage to your set.

Watching the PDP Monitor in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and centre of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause similar effect to the screen. Damages caused by the above effect are not covered by the Warranty.

Checking Parts

Sold Separately

English - 2

Control Panel

The product colour and shape may vary depending on the model.

➢

Front (or Side) Panel

Speaker Speaker

SOURCE

Displays a menu of all of the available input sources (PC, HDMI (Option)).

Press to see the on-screen menu of your PDP Monitor’s features.

VOL+,

Press to increase or decrease the volume. In the on-screen menu, use the VOL you use the œ and √ buttons on the remote control.

+,-

buttons as

SEL ,

Press to change channels. In the on-screen menu, use the SEL , buttons as you use the … and † buttons on the remote control.

(ENTER)

Press to confirm a selection.

(Power) button

Press to turn the PDP Monitor on and off.

Power Indicator

- Power Off: Blue

- Power On: Off

Remote Control Sensor

Aim the remote control towards this spot on the PDP Monitor.

English - 4

Connection Panel

The product colour and shape may vary depending on the model.

➢

Whenever you connect an audio or video system to your set, ensure that all elements are switched off.

☛

When connecting an external device, match the colour of the connection terminal to the cable.

☛

Œ POWER IN

- Connect the supplied power cord.

´ SERVICE

- Connector for service only.

ˇ HDMI/DVI IN (Option)

- Connect to the HDMI jack of a device with HDMI output.

¨ PC IN / AUDIO

- Connect to the video and audio output jack on your PC.

Supported modes for HDMI/DVI (Option)

➢

HDMI/DVI 50Hz HDMI/DVI 60Hz

480i

480p

X X

576i

These inputs can also be used as a DVI connection with separate analog audio inputs. An optional HDMI/DVI cable will be necessary to make this connection. When using the optional HDMI/DVI adapter, the DVI analog audio inputs on your PDP Monitor allow you to receive left and right audio from your DVI device. (Not compatible with PC)

- When connecting this product via HDMI or DVI to a Set Top Box, DVD Player or Games Console etc, make sure that it has been set to a compatible video output mode as shown in the table below. Failure to observe this may result in picture distortion, image breakup or no picture.

- Do not attempt to connect the HDMI/DVI connector to a PC or Laptop Graphics Card. (This will result in a blank screen being displayed)

DVI AUDIO IN L/R (Option)

- DVI audio outputs for external devices.

English - 5

576p

O X

720p

O O

1080i

O O

Viewing the Remote Control

(depending on the model)

ŒŒ

POWER button (turns the PDP Monitor on and off)

´´

Number buttons for direct channel access

ˇˇ

One/Two-digit channel selection

¨¨

Channel control button

ˆˆ

Selects the PDP mode directly

ØØ

Volume increase Volume decrease

∏∏

Temporary sound switch-off

””

Displays the main on-screen menu

’’

Picture-In-Picture On/Off

˝˝

Sound effect selection (Refer to page 12)

ÔÔ

Picture effect selection (Refer to page 10)



Adjust screen brightness to surrounding environment (Refer to page 13)

ÒÒ

Sound mode selection

ÚÚ

TruSurround XT mode button

ÆÆ

Remote control setup

ıı

Selects a target device to be controlled by the Samsung remote control (TV, DVD, STB, CABLE, VCR)

˜˜

Available source selection

¯¯

Previous channel

˘˘

Automatic Power-off

¿¿

Selects the PC mode directly

¸¸

VCR/DVD Function (Rewind, Stop, Play/Pause, Fast/Forward

˛˛

Next channel Previous channel

◊◊

Exit the on-screen menu

±±

Control the cursor in the menu

≠≠

Use to see information on the current broadcast

––

Picture freeze

——

Picture size selection

÷÷

Select the channel of sub picture (PIP)

®®

If your remote control is not functioning properly, take out the batteries and press the reset button for about 2~3 seconds. Re-insert the batteries and try using the remote control again.

The performance of the remote control may be affected by bright light.

➢

This is a special remote control for the visually impaired, and has Braille points on the Power, Channel and

➢

Volume buttons.

English - 6

Installing Batteries in the Remote Control

1 Lift the cover at the back of the remote control upward as shown in the figure.

2 Install two AAA size batteries.

Make sure to match the “+” and “–” ends of the batteries with the diagram

➢

inside the compartment.

3 Close the cover as shown in the figure.

Remove the batteries and store them in a cool, dry place if you won’t be using

➢

the remote control for a long time. The remote control can be used up to about 23 feet from the PDP Monitor. (Assuming typical PDP Monitor usage, the batteries last for about one year.)

If the remote control doesn’t work! Check the following:

➢

1. Is the PDP Monitor power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power cut, or is the power cord unplugged?

5. Is there a special fluorescent light or a neon sign nearby?

Switching Your PDP Monitor On and Off

The mains lead is attached to the rear of the PDP Monitor.

1 Plug the mains lead into an appropriate socket.

The main voltage is indicated on the rear of the PDP Monitor and the frequency is 50 or 60Hz.

➢

2 Press the (Power) button (On/Off) on the front of the PDP Monitor or press the POWER ()button on the

remote control to switch the PDP Monitor on.

3 To switch the PDP Monitor off, press the (Power) button (On/Off) on the front of the PDP Monitor or press the

POWER ()button on the remote control.

4 To switch the PDP Monitor on, press the (Power) button (On/Off) on the front of the PDP Monitor or press

the POWER ()button or number buttons on the remote control.

English - 7

Viewing the Menus

Source List : PC Edit Name

Input

Move Enter Exit

1 Press the MENU ()button.

The main menu is displayed on the screen. Its left side has four icons: Input, Picture, Sound, and Setup.

2 Press the … or † button to select one of the icons.

Press the ENTER

3 Press the … or † button to move to items in the menu.

Press the ENTER

4 Press the …/†/œ/√ button to change the selected items.

Press the MENU ()button to return to the previous menu.

5 Press the EXIT button to exit from the menu.

Freezing the Current Picture

You can freeze the picture when watching a PDP Monitor programme simply by pressing the “STILL” button. To return to normal viewing, press it again.

This function will automatically cancel five minutes later.

➢

()

button to access the icon’s sub-menu.

()

button to enter items in the menu.

English - 8

Viewing an External Signal Source

1 Press the MENU () button to display the menu.

Press the ENTER () button to select Source List.

3 Press the

4 Press the

ENTER ()

… or †

button again.

button to select the signal source, then press the

button.

vailable signal source: PC, HDMI (Option)

Source List : PC Edit Name

Input

Move Enter Return

Source List

You can select these options simply by pressing the SOURCE button

➢

on the remote control.

You can enter PC mode directly by using the PC button on the remote

➢

control unit.

Editing Device Names

You can give a name to the external source.

1 Press the MENU () button to display the menu.

Press the ENTER () button

3 Press the … or † button to select Edit Name, then press the

ENTER () button.

… or †

4 Press the

press the

5 Select the required device by pressing

button.

vailable device names: VCR, DVD, D-VHS, Cable STB, HD STB,

button to select the external source to be edited, then

ENTER ()

Satellite STB, AV Receiver, DVD Receiver, Game, Camcorder, DVD Combo, DHR (DVD HDD Recorder), or PC.

6 Press the EXIT button to exit.

button.

to select Input

… or †

, then press the

ENTER ()

PC : HDMI :

Move Enter Return

Source List : PC Edit Name

PC :

HDMI :

Input

Move Enter Return

Edit Name

Move Enter Return

----

VCR DVD

D-VHS

Cable STB

----

English - 9

Changing the Picture Standard

You can select the type of picture which best corresponds to your viewing requirements.

Mode : Dynamic Size : 16:9 Digital NR : On

SMD : On DNIe Demo : Off

Picture

1 Press the MENU () button to display the menu.

Press the … or † button to select Picture, then press the ENTER ()

button.

3 Press the ENTER () button twice.

Move Enter Return

Mode : Dynamic

Contrast 100 Brightness 50

Sharpness 75

Colour 55

Tint G 50 R 50

Colour Tone : Cool1 Reset

Mode

Dynamic

Standard

Movie

Custom

Move Enter Return

4 Select the required mode by pressing the … or † button, then press the

ENTER () button.

vailable modes: Dynamic, Standard, Movie, Custom

The settings values may vary depending on the input source.

➢

(ex. PC or HDMI (Option))

5 Press the EXIT button to exit.

You can select these options simply by pressing the P.MODE button

➢

on the remote control.

◆ Choose Dynamic for viewing the PDP Monitor during the day or when

➢

there is bright light in the room.

◆ Choose Standard for the standard factory settings.

◆ Choose Movie when viewing the movie.

◆ Choose Custom if you want to adjust the settings according to personal

preference.

Customizing the Picture Settings

Your PDP Monitor has several setting options that allow you to control the picture quality.

Picture

Mode : Dynamic Size : 16:9 Digital NR : On

SMD : On DNIe Demo : Off

Move Enter Return

Mode : Dynamic Contrast 100 Brightness 50

Sharpness 75

Colour 55

Tint G 50 R 50

Colour Tone : Cool1

Reset

Mode

Cool2

Cool1

Normal

Warm1

Move Enter Return

Warm2

◆ Contrast – Brightness – Sharpness – Colour – Tint (NTSC only)

◆ Contrast – Brightness – Colour : PC Mode

Press the œ or √ button until you reach the optimal setting.

◆ Colour Tone: Cool2/Cool1/Normal/Warm1/Warm2

◆ Reset: You can return to the factory defaults picture settings.

The reset function is set for each picture mode and colour tone.

➢

1 Press the MENU () button to display the menu.

Press the … or † button to select Picture, then press the ENTER () button.

3 Press the ENTER () button twice.

4 Select the required mode by pressing the … or † button, then press the

ENTER () button.

vailable modes: Dynamic, Standard, Movie, Custom

5 Select the required option by pressing the … or † button, then press the

ENTER () button.

6 When you are satisfied with your setting, press the ENTER () button.

7 Press the EXIT button to exit.

English - 10

Selecting the Picture Size

You can select the picture size which best corresponds to your viewing requirements.

1 Press the MENU () button to display the menu.

2 Press the … or † button to select Picture, then press the ENTER ()

Mode : Dynamic Size : 16:9 Digital NR : On

SMD : On DNIe Demo : Off

button.

3 Press the … or † button to select Size, then press the ENTER () button.

4 Select the required option by pressing the … or † button, then press the

ENTER () button.

vailable options: 16:9, Wide 4:3, Zoom, 4:3

◆ 16:9

◆ Wide 4:3

Sets the picture to 16:9 wide mode.

Magnify the size of the picture more than

4:3

16:9

Wide 4:3 Zoom

4:3

Move the screen up/down using the … or † button after selecting the by pressing the √ or ENTER () button.

◆ Zoom

◆ 4:3

Magnify the size of the picture vertically on screen.

Sets the picture to 4:3 normal mode.

5 Press the EXIT button to exit.

You can change the picture size simply by pressing the P.SIZE button

➢

on the remote control. Depending on the input source, the picture size options may vary.

➢

The items available may differ depending on the selected mode.

➢

Wide 4:3 or Zoom is not available in PC mode.

➢

Positioning and Sizing the screen using Zoom

◆ Resizing the screen using the Zoom enables the positioning and sizing of the screen to up/down direction

using the … or † button as well as the screen size.

◆ Move the screen up/down using the … or † button after selecting the by pressing the œ or √ button.

◆ Resize the screen vertically using the … or † button after selecting the by pressing the œ or √ button.

Picture

Move Enter Return

Size

Move Enter Return

Digital NR / SMD / DNIe Demo

1 Press the MENU () button to display the menu. 2 Press the … or † button to select Picture, then press the ENTER ()

button.

… or †

3 Select the required option by pressing the

ENTER ()

Available options

button.

: Digital NR,

SMD

, DNIe Demo

button, then press the

Mode : Dynamic Size : 16:9 Digital NR : On

SMD : On DNIe Demo : Off

4 When you are satisfied with your setting, press the ENTER () button.

5 Press the EXIT button to exit.

◆ Digital NR

If the signal received by the PDP Monitor is weak, you can activate this feature to reduce any static and ghosting that may appear on the screen.

◆ SMD(Smooth Motion Driver)

If you set SMD to On, you can view more natural skin and clear text even in fast moving scenes.

Only available for the High Definition models.

➢

SMD is not available in PC mode.

➢

◆ DNIe Demo:On/Off

This PDP Monitor includes the DNIe function so as to provide a high visual quality. If you set DNIe Demo to On, you can view an applied DNIe and a normal picture on the screen, for demonstration purposes. Using this function, you can view the difference in the visual quality.

➢

DNIe Demo is not available in PC mode.

➢

On/Off

On/Off (Option)

DNIeTM(Digital Natural Image engine)

This feature brings you more detailed image with 3D noise reduction, detail enhancement, contrast enhancement and white enhancement. New image compensation Algorithm gives brighter, clearer, more detailed image to you. DNIe

technology will fit every signal into your eyes.

English - 11

Picture

Move Enter Return

Sound Features

Mode : Custom Equalizer SRS TSXT : Off Auto Volume : Off

Reset

< If Game Mode is On >

Mode : Custom Equalizer SRS TSXT : Off Auto Volume : Off

Reset

Sound

Move Enter Return

Sound

Move Enter Return

Equalizer

Balance

Move Adjust Return

1kHz 3kHz 10kHz

Hz 300Hz

100

1 Press the MENU () button to display the menu.

Press the

… or †

button to select Sound, then press the

ENTER ()

3 Select the required option by pressing the … or † button, then press the

ENTER () button.

Available options: Mode, Equalizer,

(If Game Mode is On)

Reset

SRS TSXT

, Auto Volume,

4 When you are satisfied with your setting, press the ENTER () button.

5 Press the EXIT button to exit.

◆ Mode: Standard/Music/Movie/Speech/Custom You can select the type of special sound effect to be used when watching a given broadcast.

You can select these options simply by pressing the S.MODE button

➢

on the remote control.

◆ Equalizer: Balance/100Hz/300Hz/1kHz/3kHz/10kHz The PDP Monitor has several settings which allow you to control the sound quality.

If you make any changes to these settings, the sound mode is

➢

automatically switched to Custom.

◆ SRS TSXT: On/Off

TruSurround XT is a patented SRS technology that solves the of playing 5.1

multichannel content over two speakers. TruSurround delivers a compelling,

virtual surround sound experience through any two-speaker playback system, including internal PDP Monitor speakers. It is fully compatible with all multichannel formats.

You can select these options simply by pressing the

➢

button on the remote control.

TruSurround XT, SRS and Symbol are trademarks

➢

of SRS Labs, Inc. TruSurround XT technology is

SRS

incorporated under license from SRS Labs, Inc.

button.

()

◆ Auto Volume: On/Off Each broadcasting station has its own signal conditions, and so it is not easy to adjust the volume every time the channel is changed. This feature lets you automatically adjust the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low.

◆ Reset

If Game Mode is On,

the Reset Sound function is activated. Selecting the Reset function after setting the equalizer

resets the equalizer setting to the factory defaults.

English - 12

Language / Blue Screen / Melody / Energy Saving

1 Press the MENU () button to display the menu.

Press the … or † button to select Setup, then press the ENTER () button.

3 Select the required option by pressing the

ENTER ()

vailable options: Language, Game Mode, Blue Screen, Melody, PC,

button.

… or †

button, then press the

Language : English

Game Mode : Off Blue Screen : Off Melody : Off PC

Energy Saving, Screen Burn Protection, Blue Eye

4 When you are satisfied with your setting, press the

ENTER ()

button.

5 Press the EXIT button to exit.

◆ Language

It is variable depending on the model. When you start using the PDP Monitor for the first time, you must select the language which will be used for displaying menus and indications.

◆ Blue Screen

: On/Off If no signal is being received or the signal is very weak, a blue screen automatically replaces the noisy picture background. If you wish to continue viewing the poor picture, you must set the Blue Screen to Off.

◆ Melody

: On/Off

You can hear melody sound when the PDP Monitor is powered on or off.

◆ Energy Saving

: Off/Low/Medium/High This feature adjusts the screen brightness depending on the surrounding lighting conditions.

Off

: Switches off the Energy Saving mode.

Low:Operates in standard mode regardless of the surrounding illumination. Medium

Enters Medium power saving mode regardless of the surrounding illumination.

High

Enters maximum power saving mode regardless of the surrounding

illumination.

You can select these options simply by pressing the E.SAVING button on the remote control.

➢

Setup

Move Enter Return

Using Game Mode

When connecting to a game console such as PlayStationTMor XboxTM, you can enjoy a more realistic gaming experience by selecting game menu.

1 Press the MENU () button to display the menu.

Press the … or † button to select Setup, then press the ENTER () button.

3 Press the

… or †

button to select Game Mode, then press the

button.

4 Select Off or On by pressing the

… or †

button,

then

press the

ENTER ()

Language : English

Game Mode : Off Blue Screen : Off Melody : Off PC

button.

5 Press the EXIT button to exit.

To disconnect the game console and connect another external device, cancel game mode in the picture

➢

menu.

If you display the PDP Monitor menu in Game mode, the screen shakes slightly.

➢

If Game Mode is On :

➢

◆ Picture Mode is automatically changed to Custom and users cannot change the mode.

◆ Sound Mode in the Sound menu is deactivated. Adjust the sound using the equalizer.

◆ The Reset Sound function

is activated

. Selecting the Reset function after setting the equalizer resets the

equalizer setting to the factory defaults.

English - 13

Setup

Move Enter Return

Screen Burn Protection

Setup

Energy Saving : Off

Screen Burn Protection

Blue Eye : On

Move Enter Return

Screen Burn Protection

Pixel Shift

All White

Signal Pattern

Move Enter Return

Pixel Shift

Pixel Shift : On Horizontal Dot : 4 Vertical Line : 4 Time : 4

Move Enter Return

◆ Pixel Shift:Using this function, you can minutely move pixels on the PDP Monitor in horizontal or vertical direction

to minimize after image on the screen.

Set Pixel Shift to On by pressing the

Select the required option by pressing the

vailable options: Horizontal Dot, Vertical Line, Time

Optimum condition for pixel shift;

➢

Horizontal Dot

Vertical Line

Time (minute)

To reduce the possibility of screen burn, this unit is equipped with screen burn prevention technology. This technology enables you to set picture movement up/down (Vertical Line) and side to side (Horizontal Dot). The Time setting allows you to program the time between movement of the picture in minutes.

1 Press the MENU () button to display the menu.

Press the … or † button to select Setup, then press the ENTER () button.

3 Press the

4 Select the required option by pressing the

… or †

ENTER ()

the

ENTER ()

button.

button to select Screen Burn Protection, then press button.

… or †

button, then press the

Available options: Pixel Shift, All White, Signal Pattern

5 When you are satisfied with your setting, press the

ENTER ()

button.

6 Press the EXIT button to exit.

… or †

button, then press the

… or †

button, then press the

ENTER ()

button.

4 4

◆ All White:This function helps remove after images on the screen by changing the colour of pixels to white.

Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image on the screen for a long time.

◆ Signal Pattern

This function helps remove after images on the screen by moving all the pixels on the PDP Monitor according to a pattern. Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image on the screen for a long time.

To remove after images on the screen, use either “

➢

Although both of the two functions remove after images on the screen, “ The after image removal function has to be executed for a long time (approximately 1 hour) to effectively

➢

remove after images on the screen.

All White

” or “

Signal Pattern

” function.

” is more effective.

If after image is not improved after the execution of the function, repeat the function again. Press any button on the remote control to cancel this feature.

➢

English - 14

Setting the Blue Eye

You can set the power of Blue LED to be on. If the power is off when Blue Eye is off, the Blue LED goes off after 5 seconds. This will save power and reduce eye fatigue.

1 Press the MENU () button to display the menu.

2 Press the … or † button to select Setup, then press the ENTER ()

button.

3 Press the … or † button to select Blue Eye, then press the ENTER () button.

4 Select Off or On by pressing the … or † button, then press the ENTER () button.

: LED(Blue) will not come on.

◆ Off

◆ On:LED(Blue) will come on after you turn the PDP Monitor off.

5 Press the EXIT button to exit.

Energy Saving : Off

Screen Burn Protection

Blue Eye : On

Setup

Move Enter Return

Setting up Your PC Software (Based on Windows XP)

The Windows display-settings for a typical computer are shown below. But the actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. But even if your actual screens look different, the same, basic set-up information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)

1 Right click the mouse on the Windows Desktop, then click on Properties.

The Display Properties will be displayed.

2 Click on Settings tab, then set the Display Mode with reference to the

Display Modes Table. You do not need to change the Colours settings.

3 Click on Advanced. A new settings dialog box will be displayed.

4 Click on the Monitor tab, then set the Screen refresh rate with reference to the Display Modes Table.

Set the Vertical Frequency and Horizontal Frequency individually if you can do so instead of setting the

Screen refresh rate.

5 Click on OK to close the window, then Click on OK button to the Display Properties window.

Automatic re-booting may commence at this moment.

English - 15

Input Mode (PC)

Both screen position and size will vary depending on the type of PC monitor and its resolution. The table below shows all of the display modes that are supported:

Video Signal

IBM PC / AT

Compatible

◆ The interlace mode is not supported.

◆ The PDP Monitor might operate abnormally if a non-standard video format is selected.

◆ 480i/p, 576i/p, 720p, or 1080i is not available in PC mode.

◆ The PC text quality is optimum in WVGA mode (848 x 480@60Hz).

Resolution

(Dot X Line)

640 x 350 720 x 400

640 x 480

800 x 600

848 x 480

1024 x 768

Vertical frequency

(Hz)

70.086

70.087

59.940

70.000

72.809

75.000

56.250

60.317

70.000

72.188

75.000

60.000

74.769

60.004

70.069

72.000

75.029

Horizontal frequency

(kHz)

31.469

35.000

37.861

37.500

35.156

37.879

43.750

48.077

46.875

31.020

37.684

48.363

56.476

57.672

60.023

Vertical polarity

P N N

N/P

N N

N/P

P P P P N N

N/P

Horizontal

polarity

N P N

N/P

N N

N/P

P P P N N N

N/P

(N: Negative / P: Positive)

English - 16

Setting the PC

Preset to the PC mode by pressing the SOURCE () button.

➢

1 Press the MENU () button to display the menu.

Press the

Select the required option by pressing the ENTER ()

Available options: Image Lock, Position, Auto Adjustment, Image Reset

5 When you are satisfied with your setting, press the

6 Press the EXIT button to exit.

… or †

button to select Setup, then press the

… or †

button to select PC, then press the

button.

ENTER ()

… or †

button, then press the

ENTER ()

button.

Setup

Language : English

Game Mode : Off Blue Screen : Off Melody : Off PC

Move Enter Return

Image Lock Position Auto Adjustment Image Reset

Move Enter Return

◆ Image Lock: Coarse/Fine The purpose of picture quality adjustment is to remove or reduce picture noise. If the noise is not removed by Fine-tuning alone, then adjust the frequency as best as possible (coarse) and Fine-tune again. After the noise has been reduced, re-adjust the picture so that it is aligned on the center of screen.

Press the

… or †

ENTER ()

Press the appear or the picture may be blurry. Press the

button to select Coarse or Fine, then press the

button.

œ or √

button to adjust the screen quality, vertical stripes may

ENTER ()

button.

◆ Position: Adjust the PC’s screen positioning if it does not fit the PDP Monitor screen.

Adjust the position by pressing the …/†/œ/√button.

Press the

ENTER ()

button.

◆ Auto Adjustment: Auto adjustment allows the PC screen of set to self-adjust to the incoming PC video signal. The values of fine, coarse and position are adjusted automatically.

◆ Image Reset: You can replace all image settings with the factory default values.

You can select these options simply by pressing the PC button on the

➢

remote control.

Image Lock

Coarse 50 Fine 16

Move Enter Return

Position

Move Enter Return

Auto Adjustment in progress

Please wait

Image Reset has completed.

Return

English - 17

How to Install the Wall Mount Bracket

This installation guide may be different from the PDP Monitor User’s manual.

➢

Please refer to the proper installation guide for your product.

Installation Notes

◆ Contact a technician for installing the wall bracket.

◆ Samsung Electronics is not responsible for any damages to the product or harm to customers when the

installation is done by the customer.

◆ This product is for installing on cement walls. The product may not stay in place when installed on plaster or

wood.

◆ The package contents and parts supplied for the wall mount are subject to change without prior notice.

Mounting Kits

◆ Please use only the parts and components provided for wall mount installation.

Wall Mount Bracket

ASSY-HINGE

Screws

Plastic Hanger : 4 EA

1EA

How to assemble the W

all Mount Bracket

LEFT :1EA RIGHT :1EA

SCREW : 4 EA

English - 18

How to Install the Wall Mount Bracket

3 Tighten the screws of the plastic hanger (shown

in picture 2) to the back side of the PDP Monitor.

Adjust Mounting Angle

How to

Please secure the mounting bracket on the wall surface after setting its angle at 0°

➢

4 Remove the Safety Pins. Fasten the 4 plastic

latches assembled at step the PDP Monitor using the guide holes of the wall mount, push PDP Monitor on the wall mount as illustrated. Secure the PDP Monitor by inserting the Safety Pins, not to fall from the wall mount.

PDP Monitor panel

Wall attachment

panel bracket

(!)

and hook

(#)

(@)

Wall

on the back side of

down to secure the

English - 19

Setting Up Your Remote Control

After it has been set up properly, your remote control can operate in five different modes: TV, VCR, Cable, DVD, or Set-Top Box. Pressing the corresponding button on the remote control allows you to switch between these modes, and control whichever piece of equipment you choose.

The remote control might not be compatible with all DVD Players, VCRs, Cable boxes, and Set-Top Boxes.

➢

Setting Up the Remote to Operate Your VCR

1 Turn off your VCR.

Press the VCR button on your PDP’s remote control.

3 Press the SET button on your PDP’s remote control.

4 Using the number buttons on your remote control, enter three digits of the

VCR code listed on page 22 of this manual for your brand of VCR. Make sure you enter three digits of the code, even if the first digit is a “0”. (If more than one code is listed, try the first one.)

5 Press the POWER button on the remote control. Your VCR should turn on if

your remote is set up correctly.

If your VCR does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other codes listed for your brand of VCR. If no other codes are listed, try each VCR code, 000 through 080.

Note on Using Remote Control Modes: VCR When your remote control is in “VCR” mode, the volume buttons still control your PDP’s volume.

Setting Up the Remote to Operate Your Cable Box

1 Turn off your cable box.

Press the CABLE button on your PDP’s remote control.

3 Press the SET button on your PDP’s remote control.

4 Using the number buttons on your remote control, enter three digits of the

cable box code listed on page 23 of this manual for your brand of cable box. Make sure you enter three digits of the code, even if the first digit is a “0”. (If more than one code is listed, try the first one.)

5 Press the POWER button on the remote control.

Your cable box should turn on if your remote is set up correctly.

If your cable box does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other codes listed for your brand of cable box. If no other codes are listed, try each code, 000 through 046.

Note on Using Remote Control Modes: Cable Box When your remote control is in “CABLE” mode, the volume buttons still control your PDP’s volume.

continued...

English - 20

Setting Up Your Remote Control

Setting Up the Remote to Operate Your DVD

1 Turn off your DVD.

Press the DVD button on your PDP’s remote control.

3 Press the SET button on your PDP’s remote control.

4 Using the number buttons on your remote control, enter three digits of thesureur rter three digits of theh -ted, tryeeach 6566nt1 Tree ough 141jET-313 0 T06 58D0 T(N con1n ng theote Contr)19ol M566s:

English - 21

Setting Up Your Remote Control

Remote Control Codes

VCR

Brand

SAMSUNG ADMIRAL AIWA AKAI AUDIO DYNAMICS BELL&HOWELL BROKSONIC CANDLE CANON CITIZEN COLORTYME CRAIG CURTIS MATHES DAEWOO DB DIMENSIA DYNATECH ELECTROHOME EMERSON

FISHER FUNAI GENERAL ELECTRIC GO VIDEO LG(Goldstar) HARMAN KARDON HITACHI INSTANT REPLAY JC PENNEY JCL KENWOOD KLH LIOYD LOGIK LXI JVC MAGNAVOX MARANTZ MARTA KONIA ORION MEI MEMOREX MGA MIDLAND MINOLTA

Code

000 001 002 003 004 005 077 078 079 020 025 004 027 032 007 026 018 022 002 003 006 008 015 055 021 056 002 003 006 008 015 055 007 002 024 002 007 008 017 021 025 056 064 066 003 010 011 012 013 014 015 016 007 026 017 025 034 001 003 006 021 022 025 030 032 034 040 047 050 052 060 063 065 066 067 069 073 018 024 028 029 048 051 061 025 002 005 017 021 056 002 006 007 008 009 010 007 019 025 041 042 074 021 002 007 018 019 021 026 037 041 054 056 007 008 018 021 026 037 007 008 018 026 037 070 025 038 025 081 082 083 021 056 059 007 008 018 021 026 037 062 006 036 073 074 075 076 021 006 021 024 025 034 005 019 041 075

Brand

MITSUBISHI MONTGOMERY WARD MTC MULTITECH NEC OPTIMUS PANASONIC PENTAX PENTEX RESEARCH+ PHILCO PHILIPS PIONEER PORTLAND PROSCAN QUARTZ QUASAR RADIO SHACK/REALISTIC RCA SANSUI SANYO SCOTT SEARS SHARP SHIMTOM SIGNATURE SONY SYLVANIA SYMPHONIC TANDY TASHIKA TATUNG TEAC TECHNICS TEKNIKA TMK TOSHIBA TOTEVISION UNITECH VECTOR RESEARCH VICTOR VIDEO CONCEPTS VIDEOSONIC WARDS YAMAHA ZENITH

Code

019 034 041 046 020 002 025 002 005 025 038 007 008 018 026 037 062 064 020 021 056 071 072 019 041 075 008 021 056 059 021 080 019 026 039 053 015 049 055 017 018 021 056 006 018 020 021 024 025 029 034 048 056 002 017 019 021 035 041 043 057 068 076 026 018 024 003 047 052 067 006 018 019 024 028 029 041 048 051 020 034 045 015 027 033 038 058 025 027 033 044 021 025 056 059 025 018 025 006 037 025 037 068 021 006 021 025 031 066 003 019 029 051 052 002 006 002 007 026 026 007 026 002 002 003 006 019 020 021 024 025 034 038 041 007 008 018 026 037 023 027 033

continued...

English - 22

Setting Up Your Remote Control

CABLE BOX

Brand

SAMSUNG GI HAMLIN HITACHI JERROLD MACOM MAGNAVOX OAK PANASONIC PHILIPS PIONEER RCA REGAL

SAMSUNG SET-TOP BOX

Product

Ground wave STB Satellite STB CABLE STB STB DVD COMBO Satellite STB HDD COMBO Standard

SET-TOP BOX

Brand

ALPHASTAR ANAM CHANNEL MASTER CROSSDIGITAL CHAPARRAL DIRECT TV

DAEWOO DISH NETWORK SYSTEM DISHPRO DRAKE DX ANTENNA ECHOSTAR EXPRESSVU GOI GE GENERAL INSTRUMENT HTS HOME CABLE HITACHI HUGHES NETWORK IQ IQ PRISM JANEIL JERROID JVC

Code

000 001 002 003 004 005 006 007 041 003 024 031 025 030 038 039 025 030 019 023 028 026 003 022 027 037 044 019 021 023 028 004 018 020 044 014 022 040 003

Code

001 002 003 004 008 009

Code

023 043 018 034 019 035 015 016 017 019 022 045 060 061 062 065 066 067 068 074 069 070 069 018 024 032 027 025 069 070 071 069 069 065 046 047 048 063 064 069 056 022 015 017 020 020 059 063 069 070

Brand

REGENCY SA SCIENTIFIC ATLAN SPRUCER STARGATE 2000 SYLVANIA TEXSCAN TOCOM UNIVERSAL VIEWSTAR WAMER AMEX ZENITH

Product

Satellite STB HDD COMBO Premium CABLE STB HDD COMBO Standard CABLE STB HDD COMBO Premium Ground wave STB HDD COMBO Standard Ground wave STB HDD COMBO Premium

Brand

LG(Goldstar) MAGNAVOX MEMOREX MOTOROLA MACOM MITSUBISHI NEXT LEVEL PHILIPS PRIMESTAR PANASONIC PAYSAT PROSCAN RCA RADIOSHACK REALISTIC STS STAR TRAK SKY SKY LIFE SHACK STAR CHOICE SONY TOSHIBA ULTIMATE TV UNIDEN ZENITH

Code

015 023 042 043 042 043 022 036 016 016 032 033 034 019 021 023 028 046 017 029 035 037 045

Code

010 011 012 013 014

Code

044 073 016 021 036 038 039 040 041 042 016 064 018 015 047 048 064 015 016 017 021 033 036 038 039 040 041 042 067 046 049 050 063 058 059 061 062 016 065 066 051 052 053 065 066 064 057 020 027 026 031 005 006 007 064 064 054 060 015 017 028 029 030 072 060 066 016 021 037 055 056 057 024 031 068

continued...

English - 23

Setting Up Your Remote Control

SAMSUNG DVD

Product

DVD DVDR BD Record VCR COMBO VCR Record DHR COMBO

DVD

Brand

ANAM AUDIOVOX AUDIOLOGIC ANABA APEX DIGITAL AIWA BROKSONIC BLAUPUNKT B&K CURTIS MATHES CYBER HOME CLARION CIRRUS CINEVISION DAEWOO DENON FARENHEIT FISHER GPX GO VIDEO GE GREENHILL HITACHI HITEKER HOYO HARMAN / KARDON IRT INTEGRA JBL JVC JATON KENWOOD KISS KONKA KLH LG(Goldstar) LOEWE LASONIC MOBILE AUTHORITY MEMOREX MALATA MAGNAVOX MINTEK MONYKA

Code

000 001 002 003 004 005 006 007 008 009 010 011 012 013

Code

030 075 085 072 070 071 074 086 083 084 088 111 112 114 062 074 122 123 027 065 077 078 079 082 080 125 081 095 066 146 067 068 090 060 061 089 133 135 069 074 074 064 113 071 073 091 110 089 092 091 022 033 115 116 073 051 108 109 073 059 100 106 107 074 075 025 031 057 058 054 055 056 076 093 074 094 073

Product

Home Theater VCR COMBO HDD Record COMBO TWIN TRAY COMBO STB DVD COMBO DVD Receiver AV Receiver

Brand

NORCENT NEXT BASE NEC NANTAUS NESA OPTOMEDIA ELECTRONICS OPTIVIEW ONKYO PHILCO PRINCETON PROSCAN PANASONIC PHILIPS ROTEL RIO RCA RAITE ROWA SAMPO SONY SHERWOOD SVA SYLVANIA SHARP SANSUI SANYO SHINSONIC SANYO THOMSON TOSHIBA TECHNICS TVIEW TOKAI TEAC TECHWOOD TREDEX URBAN CONCEPTS VENTURER VOCOPRO YAMAHA YAMAKAWA XWAVE ZENITH

Code

014 015 016 017 018 019 020 021

Code

048 049 050 052 053 144 074 105 072 076 092 119 044 045 046 047 023 024 034 124 134 136 137 138 036 076 117 118 120 023 035 074 075 131 132 073 038 104 026 029 126 127 128 129 130 141 039 041 042 043 093 140 062 062 094 090 145 028 062 076 139 072 073 096 097 098 099 101 076 075 102 032 063 040 073 103 076 121

English - 24

Troubleshooting

Before contacting the Samsung after-sales service, perform the following simple checks. If you cannot solve the problem using the instructions below, note the model and serial number of the PDP Monitor and contact your local dealer.

No sound or picture

◆ Check that the mains lead has been connected to a wall socket.

◆ Check that you have pressed the (Power) button (On/Off) on the front panel or press the POWER ()

button on the remote control.

◆ Check the picture contrast and brightness settings.

◆ Check the volume.

Normal picture but no sound

◆ Check the volume.

◆ Check whether the volume MUTE button on the remote control has been pressed.

No picture or black and white picture

◆ Adjust the colour settings.

◆ Check that the broadcast system selected is correct.

Sound and picture interference

◆ Try to identify the electrical appliance that is affecting the PDP Monitor, then move it further away.

◆ Plug the PDP Monitor into a different mains socket.

Blurred or snowy picture, distorted sound

◆ Check the direction, location and connections of your aerial.

This interference often occurs due to the use of an indoor aerial.

Remote control malfunctions

◆ Replace the remote control batteries.

◆ Clean the upper edge of the remote control (transmission window).

◆ Check that the “+” and “–” ends of the batteries are inserted correctly.

◆ Check that the batteries are drained.

Screen is black and power indicator light blinks steadily

◆ On your computer check; Power, Signal Cable.

◆ The PDP Monitor is using its power management system.

◆ Move the computer’s mouse or press any key on the keyboard.

◆ On your equipment check (STB, DVD, etc) ; Power, Signal Cable.

◆ The PDP Monitor is using its power management system.

◆ Press the Source button on the panel or remote control.

◆ Turn the PDP Monitor off and on.

English - 25

This page is intentionally

left blank.

This page is intentionally

left blank.

Samsung PDP-MONITOR User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

User Instructions

Checking Parts

Control Panel

Connection Panel

Installing Batteries in the Remote Control

Switching Your PDP Monitor On and Off

Viewing the Menus

Freezing the Current Picture

Viewing an External Signal Source

Editing Device Names

Changing the Picture Standard

Customizing the Picture Settings

Selecting the Picture Size

, DNIe Demo

◆ Digital NR

Sound Features

◆ Language

◆ Blue Screen

◆ Melody

◆ Energy Saving

Using Game Mode

Screen Burn Protection

Setting the Blue Eye

Setting up Your PC Software (Based on Windows XP)

Input Mode (PC)

Setting the PC

How to Install the Wall Mount Bracket

Setting Up Your Remote Control

Troubleshooting