Samsung P50HP-2, P63FP-2 User Manual
LCD MONITOR
quick start guide
P50HP-2, P63FP-2
ii
Introduction
Package Contents
Note
Please make sure the following items are included with your PDP Display.
If any items are missing, contact your dealer.
Contact a local dealer
to buy optional items.
Checking the Contents of the Package
Remove the lock from the package box, as shown in the figure above.
• After unpacking the package, make sure to check the contents of the package.
•
• After unpacking, you may use the lower part of the package box as a temporary stand for
Unpacking
Lift up the package box by
holding the grooves on
both sides of the package
box.
Note
Make sure to keep the package box for transporting the product in the future.
product test or operation check.
Check the contents of the
package.
Remove the Styrofoam
and vinyl cover.
Manuals
Introduction
PDP Display
Quick Setup Guide Warranty Card
(Not available in all loca-
tions)
Cables
Power Cord D-Sub Cable
Others
Remote Control Batteries (AAA X 2)
(Not available in all loca-
tions)
User's Guide
Ferrite Core for Power
Cord
Sold separately
DVI Cable Wall Mount KIT BNC to BNC Cable
Network Box RGB to BNC Cable
Ferrite Core
• The ferrite cores are used to shield the cables from interference.
When connecting a cable, open the ferrite core and clip it
•
around the cable near the plug.
Your PDP Display
Front
Introduction
SOURCE button [SOURCE]
Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the PDP Display at the
time.
[PC] → [DVI] → [AV] → [HDMI] → [MagicInfo] → [BNC] → [Component]
Note
• MagicInfo can only be enabled when a network box is connected.
and
• The HDMI port
network box cannot be connected at the same time.
Enter button [ ]
Activates a highlighted menu item.
MENU button [MENU]
Opens the on-screen menu and exits from the menu. Also use to exit the
OSD menu or return to the previous menu.
- VOL+
Moves from one menu item to another horizontally or adjusts selected
menu values. When OSD is not on the screen, push the button to adjust
volume.
SEL
Moves from one menu item to another vertically or adjusts selected menu
values.
Power button [ ]
Use this button for turning the PDP Display on and off.
Power indicator
Shows PowerSaver mode by blinking green
Note
Introduction
Rear
See PowerSaver described
power saving functions. For energy conservation, turn your PDP Display
OFF when it is not needed or when leaving it unattended for long periods.
in the manual for further information regarding
Remote Control Sensor
Aim the remote control towards this spot on the PDP Display.
Note
For detailed information concerning cable connections, refer to Connecting Cables under
Setup. The PDP Display's configuration at the back may vary slightly depending on the PDP
Display model.
POWER IN
The power cord plugs into the PDP Display
and the wall plug.
Introduction
RS232C OUT/IN (RS232C Serial PORT)
MDC(Multiple Display Control) Program Port
RGB IN (PC Connection Terminal (In-
put))
• Use a D-Sub Cable (15 pin D-Sub) - PC
mode (Analog PC)
• Connect the RGB IN port on the monitor
to the BNC port on the PC using the RGB
to BNC cable.
DVI IN (PC Video Connection Terminal)
Connect the [DVI IN] port on the monitor to
the DVI port on the PC using the DVI cable.
DVI/RGB AUDIO IN (PC/DVI Audio Con-
nection Terminal (Input))
AV/COMPONENT AUDIO IN [R-AUDIO-
L]
Connect the port of the DVD, VCR (DVD /
DTV Set-Top Box) to the [R-AUDIO-L] port
of the PDP Display.
DVI OUT
• Connect a monitor to another monitor
through a DVI cable.
• Connect the [DVI OUT] port on the monitor to the [HDMI IN] port on the other
monitor using the DVI to HDMI cable.
• DVI, HDMI and network signals sent via
the [DVI OUT] port are displayed on the
second display which has the DVI IN port.
Note
Up to
6 Full HD or 10 HD monitors can be
connected (May differ depending on the
product).
Introduction
AV IN [VIDEO]
Connect the AV IN [VIDEO] terminal of your
monitor to the video output terminal of the
external device using a VIDEO cable.
AUDIO OUT
Headphone/External speaker output terminal.
HDMI IN
Connect the HDMI terminal at the back of
your PDP Display to the HDMI terminal of
your digital output device using a HDMI cable.
Up to HDMI cable 1.2 can be supported.
BNC OUT [R, G, B, H, V] (BNC Terminal
(Output))
BNC (Analog PC) Connection: connecting
the R, G, B, H, V ports.
The number of PDP Displays that can be
connected to the loopout depends on the cables, signal source, etc. With cables or signal
source where there is no degradation, up to
10 PDP Displays can be connected (May not
be supported depending on the connected
cable).
BNC/COMPONENT IN [R/PR, G/Y, B/
PB, H, V] (BNC/Component Connection Terminal (input))
- During BNC input, please check specifications for the input ports below.
• [R/PR] --> Red port input
• [G/Y] --> Green port input
• [B/PB] --> Blue port input
- During component input, please check
specifications for the input ports below.
• [R/PR] --> Red port input
• [G/Y] --> Green port input
• [B/PB] --> Blue port input
Introduction
Kensington Lock
The Kensington Lock is a device used to
physically fix the system when using it in a
public place. The locking device has to be
purchased separately. The appearance and
locking method may differ from the illustration depending on the manufacturer. Refer to
the manual provided with the Kensington
Lock for proper use.
Note
The location of the Kensington Lock may be
different depending on its model.
Using the Anti-Theft Kensington Lock
Note
See Connecting Cables for further information regarding cable connections.
Remote Control
Note
The performance of the remote control may be affected by a TV or other electronic device
operating near the PDP Display , causing a malfunction due to interference with the frequency.
1. Insert the locking device into the Ken-
sington slot on the Monitor and turn
it in the locking direction
2. Connect the Kensington Lock cable.
3.
Fix the Kensington Lock to a desk or a
heavy stationary object.
.
Loading...