SAMSUNG LSC460HN05-W Specification

MODEL

LSC460HN05-W

Doc. No

Page

1 / 30

SAMSUNG TFT-LCD

MODEL: LSC460HN05-W

Samsung Display Co., LTD

SAMSUNG Confidential

SAMSUNG Confidential

MODEL

LSC460HN05-W

Doc. No

Page

2 / 30

General Description

Description

This model uses a liquid crystal display (LCD) of amorphous silicon TFT as switching components. This

model is composed of a TFT LCD panel, a driver circuit, and an ass’y KIT of source PBA. This 46.0”

model has a resolution of a 1920 x 1080 and can display up to 16.7 million colors with the wide viewing

angle of 89° or a higher degree in all directions. This panel is designed to support applications by

providing a excellent performance function of the flat panel display such as home-alone multimedia TFT­LCD TV and a high definition TV.

General Information

Features

 RoHS compliance (Pb-free)
 High contrast ratio & aperture ratio with the wide color gamut
 SPVA(Super patterned vertical align) mode
 Wide viewing angle (±178°)
 High speed response
 FHD resolution (16:9)
 Low power consumption
 DE (Data enable) mode
 The interface (2pixel/clock) of 2ch LVDS (Low voltage differential signaling)

Items

Specification

Unit

Note

Active Display Area

1018.08(H) x 572.67(V)

㎜

Switching Components

a-Si TFT Active matrix

Glass Size

TFT : 1036.08(H) x 591.4(V)
CF : 1030.88 (H) x 588.7 (V)

mm

Panel Size

1036.08(H) x 591.4(V)

mm

1.80(D)

mm

Weight

2350 (max 2500)

g

± 10%

Display Colors

16.7M (True Display)

1.07B (Dithered 10bit)

color

Number of Pixels

1,920 × 1,080

pixel

16 : 9

Pixel Arrangement

RGB Vertical Stripe

Display Mode

Normally Black

Surface Treatment

Antiglare

Haze

Haze 2.3%

± 2.1

Hardness

Hard coating : 2H

SAMSUNG Confidential

MODEL

LSC460HN05-W

Doc. No

Page

3 / 30

1. Absolute Maximum Ratings

If the figures on measuring instruments exceed maximum ratings, it can cause the malfunction or the
unrecoverable damage on the device.

Item

Symbol

Min.

Max.

Unit

Note

Power supply voltage

V

DD

11

13

V

(1)

Temperature for storage

(Temperature of glass surface)

T

STG

-20

65

℃

(2),(4)

Operating temperature

T

OPR

0

50

℃

(2),(5)

Humidity for storage

H

STG

5

90

%RH

(2),(4)

Operating humidity

H

STG

20

90

%RG

(2),(5)

Endurance on static electricity

150

V

(3)

Note (1) The power supply voltage at Ta= 25 ± 2 °C
(2) Temperature and the range of relative humidity are shown in the figure below.

a. 90 % RH Max. (Ta ≤ 39 °C)
b. The relative humidity is 90% or less. (Ta ＞39 °C)
c. No condensation

(3) Keep the static electricity under 150V in Polarizer attaching process.
(4) Operating condition with source PCB
(5) Storage temperature condition including glass
(6) Condition without packing. (Unpacking condition)

Fig. Range for temperature and relative humidity

SAMSUNG Confidential

MODEL

LSC460HN05-W

Doc. No

Page

4 / 30

2. Optical characteristics – Sony & VD Model Attached Reference

The optical characteristics should be measured in the dark room or the space surrounded by the similar setting.

Measuring equipment : TOPCON RD-80S, TOPCON SR-3 ,ELDIM EZ-Contrast
(Ta = 25 ± 2°C, VDD=12.0V, fv=60Hz, f

DCLK

=148.5MHz, Light source: LTY460HJ07 Sony BLU )

Item

Symbol

Condition

Min.

Typ.

Max.

Unit

Light Source

Note

Contrast Ratio

(Center of screen)

C/R* 2500

5000

-

LTY460HJ07

Sony BLU

(1)

SR-3

Response

Time

G-to-G

Tg

T

PAN,SUR

=25℃

- 8 16

msec

LTY460HJ07

Sony BLU

(3)

RD-80S

Luminance of White

(At the center of screen)

YL

Normal
qL,R=0

qU,D=0

Viewing

Angle

330

400

-

cd/m

2

LTY460HJ07

Sony BLU

(7)

SR-3

Transmittance

(At the Center of screen)

T

5.1

5.7 - %

SDC

Standard

Color

Chromaticity

(CIE 1931)

Red

Rx

TYP.

-0.03

0.648

TYP.

+0.03

Simulation

With

SONY BLU

Spectrum

(5),(6), (9)

SR-3

(Appendix2)

Ry

0.327

Green

Gx

0.299

Gy

0.614

Blue

Bx

0.155

By

0.052

White

Wx

0.268

Wy

0.274

Color Gamut

- - 75 - %

(5)

SR-3

Color Temperature

- - 11000

-

K

Viewing

Angle

Hor.

qL

C/R≥10

79

89

-

Degree

LTY460HJ07

Sony BLU

(6)

SR-3

EZ-Contrast

qR

79

89

-

Ver.

qU

79

89

-

qD

79

89

-

Transmittance Uniformity

(9 Points)

B

uni

- - 20

%

SDC

Standard

(2)

SR-3

- - 30

%

LTY460HJ07

Sony BLU

2 Point Gamma

γ

7G ~57G

1.7

2.2

2.7

LTY460HJ07

Sony BLU

(8)

SR-3

Notice

(a) Setup for test equipment

The measurement should be executed in a stable, windless, and dark room for 40min and 60min after
operating the panel at the given temperature for stabilization of the standard light. (SDC uses the standard
luminance of the LTY460HJ07 Sony BLU.)
This measurement should be measured at the center of screen.

The environment condition: Ta = 25 ± 2 °C
(b) LTY460HJ07 Sony BLU is consist of two diffuser sheets and one prism sheet and LED light source..
(c) SDC Standard Light Source
The Temperature of color is 12161K. The coordinate of color is Wx 0.277, Wy 0.268.

The luminance of this product is 6833.0cd/m2.

MODEL

LSC460HN05-W

Doc. No

Page

5 / 30

Photo detector

Field

SR-3

2°/1°

RD-80S

1°

- Definition of the test point

Note (1) Definition of contrast ratio (C/R)
: The ratio of gray max (Gmax) & gray min (Gmin) at the center point ⑤ of the panel

The measurement goes in LTY460HJ07 Sony BLU.

Gmax : The luminance with all white pixels
Gmin : The luminance with all black pixels

Note (2) Definition of the brightness uniformity of 9 points (Test pattern : The full white)

The measurement shall be executed with the LTY460HJ07 Sony BLU.

Bmax : The maximum brightness
Bmin : The minimum brightness

C R

G

G

/

max

min



SAMSUNG Confidential

SAMSUNG Confidential

MODEL

LSC460HN05-W

Doc. No

Page

6 / 30

Note (3) Definition of the response time : Sum of Tr, Tf

※ G-to-G : Average response time between whole gray scale to whole gray scale.

The response time is the value that was measured after it was operated in LTY460HJ07 Sony BLU for
one hour.( at room temperature)
 SONY tunes up response time based on 2012 Model standard.

Note (4) The definition of luminance of white: The luminance of white at the center point ⑤

The measurement shall be executed with the LTY460HJ07 Sony BLU.

Note (5) The definition of chromaticity (CIE 1931)

The color coordinate of red, green, blue and white at the center point ⑤
The measurement shall be executed with the LTY460HJ07 Sony BLU.

Note (6) Definition of viewing angle

: The range of viewing angle (C/R ≥10)

The measurement shall be executed with the LTY460HJ07 Sony BLU.

Note (7) Definition of transmissivity

The measurement shall be executed with the SDC Standard.

Note (8) Definition of Gamma

The response

Of optical instruments

Display data

Gamma X Y

X Z B B B

lum

lum



   

log( / ) / log( / )

( ) / ( )

min max min

100 100

100

Y: Measurement Level / Z: Measurement Brightness
B

max

: Maximum Brightness / B

min

: Minimum Brightness

SAMSUNG Confidential

MODEL

LSC460HN05-W

Doc. No

Page

7 / 30

Color x = , Color y =

Note (9) Definition of Simulation with BLU Spectrum

Simulated Color Chromaticity

Xsim = Simulated Spectrum X CIE Color Matching Function x

Ysim = Simulated Spectrum X CIE Color Matching Function y

Zsim = Simulated Spectrum X CIE Color Matching Function z

Simulated Spectrum = Panel Transmittance Spectrum X Standard BLU Spectrum (Appendix2)

SAMSUNG Confidential

MODEL

LSC460HN05-W

Doc. No

Page

8 / 30

3. Electrical characteristics – Sony Model Attached Reference file

3.1 TFT LCD Module

The connector for the display data & timing signal should be connected.

Ta = 25°C ± 2 °C

Item

Symb

ol

Min.

Typ.

Max.

Unit

Note

Voltage of power supply

V

DD

11

12.0

13

V

(1)

Power

Consumption

(a) Black

I

DD

-

260

-

mA

(2),(3)

(b) White

-

270

350

mA

(c) Max (Sub V-Stripe)

-

700

840

mA

Vsync frequency

f

V

47

60

63

Hz

Hsync frequency

f

H

50

67.5

73

kHz

Main frequency

Fdclk

130

148.5

155

MHz

Rush current

I

RUSH

- - 3

A

(4)

Note (1) The ripple voltage should be controlled fewer than 10% of V

DD

(Typ.) voltage.
(2) VDD = 12.0V, DC Current.
(3) Power dissipation check pattern (LCD Module only)

(4) Conditions for measurement

a) Black pattern b) White pattern c) Max Pattern (Sub V-Stripe)

MODEL

LSC460HN05-W

Doc. No

Page

9 / 30

4. Block diagram

SAMSUNG Confidential

SAMSUNG Confidential

MODEL

LSC460HN05-W

Doc. No

Page

10 / 30

5. The Pin assignment in the input terminal

5.1. Input signal & power
Connector : FI-RE51S-HF (JAE)

Pin

Symbol

Description

Pin

Symbol

Description

1

VIN

DC power supply

26

RAEP

Even LVDS Signal +

2

VIN

DC power supply

27

RBEN

Even LVDS Signal -

3

VIN

DC power supply

28

RBEP

Even LVDS Signal +

4

VIN

DC power supply

29

RCEN

Even LVDS Signal -

5

VIN

DC power supply

30

RCEP

Even LVDS Signal +

6

N.C.

No Connection

31

GND

Ground

7

GND

Ground

32

RCLKEN

Even LVDS Signal -

8

GND

Ground

33

RCLKEP

Even LVDS Signal +

9

GND

Ground

34

GND

Ground

10

RAON

Odd LVDS Signal -

35

RDEN

Even LVDS Signal -

11

RAOP

Odd LVDS Signal +

36

RDEP

Even LVDS Signal +

12

RBON

Odd LVDS Signal -

37

REEN

Even LVDS Signal -

13

RBOP

Odd LVDS Signal +

38

REEP

Even LVDS Signal +

14

RCON

Odd LVDS Signal -

39

GND

Ground

15

RCOP

Odd LVDS Signal +

40

SCL_I

I2C SCL

16

GND

Ground

41

SDA_I

I2C SDA

17

RCLKON

Odd LVDS Signal -

42

N.C.

No connection

18

RCLKOP

Odd LVDS Signal +

43

BUS_SW

Bus Switching

19

GND

Ground

44

N.C.

No connection

20

RDON

Odd LVDS Signal -

45

N.C.

No connection

21

RDOP

Odd LVDS Signal +

46

LUT SEL0

DCC LUT Select 0

22

REON

Odd LVDS Signal -

47

LUT SEL1

DCC LUT Select 1

23

REOP

Odd LVDS Signal +

48

LUT SEL2

DCC LUT Select 2

24

GND

Ground

49

N.C.

No connection

25

RAEN

Even LVDS Signal -

50

N.C.

No connection

51

LVDS Option

LVDS Option

SAMSUNG Confidential

MODEL

LSC460HN05-W

Doc. No

Page

11 / 30

Note (2) Pin number which starts from the left side.

a. Power GND pins should be connected to the LCD’s metal chassis.

b. All power input pins should be connected together.

c. All NC pins should be separated from other signal or power.

Note(3) LVDS OPTION : IF THIS PIN : LOW (GND V)/ NC → JEIDA LVDS FORMAT

OTHERWISE : HIGH (3.3V) → NORMAL NS LVDS FORMAT

Note(4) 46

th

Pin Aging Enable PIN / IF this Pin HIGH(3.3V)

→ BIST MODE (Rolling Pattern is operated by Only 3.3V input)

Fig . The diagram of connector

MODEL

LSC460HN05-W

Doc. No

Page

12 / 30

5.2 LVDS Interface

- LVDS receiver : T-con (merged)

- Data format

LVDS pin

JEIDA -DATA

Normal-Data

TxOUT/RxIN0

TxIN/RxOUT0

R2

R0

TxIN/RxOUT1

R3

R1

TxIN/RxOUT2

R4

R2

TxIN/RxOUT3

R5

R3

TxIN/RxOUT4

R6

R4

TxIN/RxOUT6

R7

R5

TxIN/RxOUT7

G2

G0

TxOUT/RxIN1

TxIN/RxOUT8

G3

G1

TxIN/RxOUT9

G4

G2

TxIN/RxOUT12

G5

G3

TxIN/RxOUT13

G6

G4

TxIN/RxOUT14

G7

G5

TxIN/RxOUT15

B2

B0

TxIN/RxOUT18

B3

B1

TxOUT/RxIN2

TxIN/RxOUT19

B4

B2

TxIN/RxOUT20

B5

B3

TxIN/RxOUT21

B6

B4

TxIN/RxOUT22

B7

B5

TxIN/RxOUT24

HSYNC

HSYNC

TxIN/RxOUT25

VSYNC

VSYNC

TxIN/RxOUT26

DEN

DE

TxOUT/RxIN3

TxIN/RxOUT27

R0

R6

TxIN/RxOUT5

R1

R7

TxIN/RxOUT10

G0

G6

TxIN/RxOUT11

G1

G7

TxIN/RxOUT16

B0

B6

TxIN/RxOUT17

B1

B7

TxIN/RxOUT23

RESERVED

RESERVED

SAMSUNG Confidential

SAMSUNG Confidential

MODEL

LSC460HN05-W

Doc. No

Page

13 / 30

5.3 Input signals, basic display colors and the gray scale of each color.

COLOR

DISPLAY

(8bit)

DATA SIGNAL

GRAY
SCALE
LEVEL

RED

GREEN

BLUE

R0

R1

R2

R3

R4

R5

R6

R7

G0

G1

G2

G3

G4

G5

G6

G7

B0

B1

B2

B3

B4

B5

B6

B7

BASIC

COLOR

BLACK

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

-

BLUE

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

1

1

1

1

1

1

1

-

GREEN

0

0

0

0

0

0

0

0

1

1

1

1

1

1

1

1

0

0

0

0

0

0

0

0

-

CYAN

0

0

0

0

0

0

0

0

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

-

RED

1

1

1

1

1

1

1

1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

-

MAGENTA

1

1

1

1

1

1

1

1

0

0

0

0

0

0

0

0

1

1

1

1

1

1

1

1

-

YELLOW

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

0

0

0

0

0

0

0

0

-

WHITE

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

-

GRAY

SCALE

OF

RED

BLACK

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

R0

DARK

↑

↓

LIGHT

1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

R1

0

1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

R2

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

R3~

R252

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

1

0

1

1

1

1

1

1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

R253

0

1

1

1

1

1

1

1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

R254

RED

1

1

1

1

1

1

1

1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

R255

GRAY

SCALE

OF

GREEN

BLACK

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

G0

DARK

↑

↓

LIGHT

0

0

0

0

0

0

0

0

1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

G1

0

0

0

0

0

0

0

0

0

1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

G2

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

G3~

G252
:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

0

0

0

0

0

0

0

0

1

0

1

1

1

1

1

1

0

0

0

0

0

0

0

0

G253

0

0

0

0

0

0

0

0

0

1

1

1

1

1

1

1

0

0

0

0

0

0

0

0

G254

GREEN

0

0

0

0

0

0

0

0

1

1

1

1

1

1

1

1

0

0

0

0

0

0

0

0

G255

GRAY

SCALE

OF

BLUE

BLACK

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

B0

DARK

↑

↓

LIGHT

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

0

0

0

0

0

0

0

B1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

0

0

0

0

0

0

B2

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

B3~

B252

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

0

1

1

1

1

1

1

B253

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

1

1

1

1

1

1

B254

BLUE

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

1

1

1

1

1

1

1

B255

Note) The definition of gray :

Rn : Red gray, Gn : Green gray, Bn : Blue gray (n = Gray level)

Input signal : 0 = Low level voltage, 1 = High level voltage

SAMSUNG Confidential

MODEL

LSC460HN05-W

Doc. No

Page

14 / 30

6. Interface timing

6.1 The parameters of timing ( Only DE mode )

SIGNAL

ITEM

SMBOL

MIN.

TYP.

MAX.

Unit

NOTE

Clock

Frequency

1/T

C

130

148.5

155

MHz

-

Hsync

F

H

50

67.5

73

KHz

-

Vsync

F

V

47

60

63

Hz

-

Term for the

vertical

display

Active

display

period

T

VD

-

1080

-

Lines

-

Total vertical

T

V

1100

1125

1480

Lines

-

Term for the

horizontal

display

Active

display

period

T

HD

-

1920

-

Clocks

-

Total

Horizontal

T

H

2150

2200

2450

clocks

-

Note) These products don’t have to receive the signal of Hsync & Vsync from the input device.

(1) Key points when testing: TTL controls the signal and the CLK at the input terminal of LVDS Tx of the

system.

(2) Internal VDD = 3.3V

(3) Spread spectrum

- The limit of spread spectrum's range of SET in which the LCD module is assembled should be within ± 3 %.

SAMSUNG Confidential

MODEL

LSC460HN05-W

Doc. No

Page

15 / 30

6.2 Timing diagrams of interface signal (Only DE mode )

SAMSUNG Confidential

MODEL

LSC460HN05-W

Doc. No

Page

16 / 30

6.3 Characteristics of Input data of LVDS

ITEM

SYMBOL

Min.

Typ.

Max.

UNIT

NOTE

Differential input high

threshold voltage

VTH

- - +100

mV

V

CM

= 1.2V

Differential input low

threshold voltage

VTL

-100 - -

mV

Input common mode voltage

V

CM

0.2

1.2

2.0 V -

Differential Input Voltage

|V

ID

|

100

-

600

mV

|V

ID

|=100mV

Input data position

F

IN

=80MHz

t

RSRM

- - 450

ps

t

RSLM

-450

-

ps

Notice The spread spectrum should be 0% when the skew is measured.
Position of a measurement is T-CON LVDS input pin

SAMSUNG Confidential

MODEL

LSC460HN05-W

Doc. No

Page

17 / 30

6.4 The sequence of power on and off
To prevent a latch-up phenomena or the DC operation of the LCD Module, the power on/off sequence should
be accorded with the settings described in the diagram below.

 The supply voltage of the external system for the Module input should be the same as the definition of V

DD

.

 Apply the lamp voltage within the LCD operation range. When the back light turns on before the LCD

operation or the LCD turns off before the back light turns off, the display may momentarily show abnormal
screen.

 In case of V

DD

= off level, please keep the level of input signals low or keep a high impedance.

 T4 should be measured after the Module has been fully discharged between power off and on period.
 Interface signal should not be kept at high impedance when the power is on.
 While the V

DD

is off level, please keep the level of input signals low or keep a high impedance condition.

 The figure of T4 should be measured after the module has been fully discharged between the periods

when the power is on and off.



6.5 INPUT SPREAD SPECTRUM SPECIFICATION

SAMSUNG Confidential

MODEL

LSC460HN05-W

Doc. No

Page

18 / 30

7. Outline dimension

7.1 The adhesive size of POL
The next figure shows the size of POL on the drawing sheet attached to the panel for BLU design.

<Figure.>
The POL size of CF : 1029.28 X586.25 ± 0.2mm
The POL size of TFT: 1028.88X586.25 ± 0.2mm
The total adhesion allowance of POL is ± 0.8㎜

7.2 The drawing sheet for the size of the OLB bonding

MODEL

LSC460HN05-W

Doc. No

Page

19 / 30

8. Reliability test

8.1 Panel

Item

Test Condition

Quantity

Note

HTOL

60 ℃ (Panel change 500hr / circuit change 250hr)

8

LTOL

-5 ℃ (Panel change 500hr / circuit change 250hr)

4

THB

50 ℃ / 90 %RH(Panel change 500hr / circuit change 250hr)

10

ASG

Low

temperature

Max. frequency 25℃~-40℃

Each

Cell

ASG Product Only

ASG

High

Temperature

Min. frequency 60℃ operation 96hr

Each

Cell

ASG Product Only

Image sticking

25 ℃ / Mosaic pattern(9*10) 12hrs

8

Rolling pattern 12hrs / 3cycles

Decompressio

n

-40~50℃, 0m(0ft) ~ 13,700m(45,000ft), 72.5Hr

4

HTS

70 ℃, Storage

4

LTS

-25 ℃, Storage

4

Transportation

condition

drop(20cm) → temperature/humidity(-30~60℃ / 40℃ 90%RH)
→ pressure → vibration(5~200Hz 1.05Grms, 2hr) → drop(20cm)

1pallet

WHTS

60 ℃ / 75 %RH , Storage 500hr

4

Noise

Electromagnetic noise: Overall 23dB 이하

2

Complex

stress

-20℃~60℃, 0~90%RH, 2cycle

4

ESD

S-IC Input ±7KV, Output ±4KV

4

EOS (optional)

Item

Test condition

Vin Input

step

Surge combination (High impedance)

Pass Condition: 5kV under

Signal Input

step

Surge combination (High impedance)

Pass Condition: 120V under

2

[ Criteria on evaluation]
There should be no change of the product, which may affect to the practical display functions, when the
display quality test is executed under the normal operation setting.
* HTOL/ LTOL : The operating cycle on the high and low temperature
* THB : Temperature humidity slant
* HTS/LTS : The storage at the high and low temperature

* WHTS : The storage in the high temperature with the high humidity

SAMSUNG Confidential

SAMSUNG Confidential

MODEL

LSC460HN05-W

Doc. No

Page

20 / 30

9. General precautions

9.1 Handling

(a) When the panel kit and BLU kit are assembled, the panel kit and BLU kit should be attached to the

set system firmly by combining each mounted holes. Be careful not to give the mechanical stress.

(b) Be careful not to give any extra mechanical stress to the panel when designing the set, and BLU kit.

(c) Be cautious not to give any strong mechanical shock and / or any forces to the panel kit.
Applying the any forces to the panel may cause the abnormal operation or the damage to the panel

kit and the back light unit kit.

(d) Refrain from applying any forces to the source PBA and the drive IC in the process of the handling

or installing to the set. If any forces are applied to the products, it may cause damage or a
malfunction in the panel kit.

(e) Refrain from applying any forces which cause a constant shock to the back side of panel kit, the set

design and BLU kit. If any forces are applied to the products, it may cause an abnormal display, a
functional failure and etc.

(f) Note that polarizer could be damaged easily.

Do not press or scratch the bare surface with the material which is harder than a HB pencil lead.

(g) Wipe off water droplets or oil immediately. If you leave the droplets for a long time on the product, a

staining or the discoloration may occur.

(h) If the surface of the polarizer is dirty, clean it using the absorbent cotton or the soft cloth.

(i) Desirable cleaners are water or IPA (Isopropyl Alcohol).

Do not use Kenton type materials (ex. Acetone), Ethyl alcohol, Toluene, Ethyl acid or Methyl chloride.
These might cause the permanent damage to the polarizer due to chemical reaction.

(j) If the liquid crystal material leaks from the panel, this should be kept away from the eyes or mouth.

If this contacts to hands, legs, or clothes, you must washed it away with soap thoroughly and see a
doctor for the medical examination.

(k) Protect the panel kit and BLU Kit out of the static electricity. Otherwise the circuit IC could be

damaged.

- Reference : Process control standard of SDC

No.

Item

Control standard

1

Ionizer

All Equipment should be controlled under 150V.(Typ. 100V)

2

Carrying Roller

Carrying Roller should be controlled under 200V.

3

Equipment Ground

Resistance

All Equipment Ground Should be less than 1ohm.

SAMSUNG Confidential

MODEL

LSC460HN05-W

Doc. No

Page

21 / 30

(l) Remove the stains with finger-stalls wearing soft gloves in order to keep the display clean in the

process of the incoming inspection and the assembly process.

(m) Do not pull or fold the source drive IC which connects to the source PBA and the panel or the gate

drive IC.

(n) Do not pull, fold or bend the source drive IC and the gate drive IC in any processes.

If not, the source drive IC could be bent one time in the process of assembling the panel Kit and the
BLU Kit.

(o) Do not adjust the variable resistor located on the panel kit and BLU kit except when adjusting the

flicker.
(p) Do not touch the pins of the interface connector directly with bare hands.
(q) Be cautious not to be peeled off the protection film.

(r) The protection film for the polarizer on the panel kit should be slowly peeled off just before using so

that the electrostatic charge can be minimized.

(s) The panel kit and BLU kit have high frequency circuits. The sufficient suppression to the EMI should

be done by the set manufacturers.

(t) The set of which the panel is assembled shall not be twisted. If the product is twisted, it may cause

the damage on the product.

(u) Surface Temp. of IC should be controlled less than 100℃, operating over the Temp. can cause the

damage or decrease of lifetime.

- Make sure to peel off slowly
(It is recommended to peel it off at the speed of more than 8sec.
constantly.)

- The peeling direction is shown at the Fig

- Instruct the ground worker to work with the adequate methods
such as the antistatic wrist band.

- Maker sure to be grounded the source PBA while peeling of the
protection film.

- Ionized air should be blown over during the peeling

- The protection film should not t be contacted to the source drive
IC.

- If the adhesive stains remain on the polarizer after the
protection film is peeled off, please move stains with isopropyl­alcohol liquid.

MODEL

LSC460HN05-W

Doc. No

Page

22 / 30

9.2 Storage

The storage condition for packing

ITEM

Unit

Min.

Max.

Storage

Temperature

(℃)

Storage

Humidity

(%rH)

Storage life

6 months

Storage

Condition

(1) The storage room should provide good ventilation and temperature control.
(2) Products should not be placed on the floor, but on the Pallet away from a wall.
(3) Prevent products from direct sunlight, moisture nor water; Be cautious of a buildup of

condensation.
(4) Avoid other hazardous environment while storing goods.
(5) If products delivered or kept in conditions of the recommended temperature or humidity,

we recommend you leave them at a circumstance which is shown in the following table.

period

1 month

2 months

3 months

4 months

5 months

6 months

Baking

Condition

No Baking

50℃, 10%

24Hr

50℃, 10%, 48Hr

9.3 Operation
(a) Do not connect or disconnect the FFC cable during the "Power On" condition.
(b) Power supply should be always turned on and off by the "Power on/off sequence"
(c) The module has high frequency circuits. The sufficient suppression to the electromagnetic interference

should be done by the system manufacturers. The grounding and shielding methods is important to
minimize the interference.

(d) The cables between TV SET connector and Control PBA interface cable should be connected directly

to have a minimized length. A longer cable between TV SET connector and Control PBA interface
cable maybe operate abnormal display

(e) Recommend to age for over 1 hour at least in the state, which the product is driving initially to stabilize

the characteristic of the initial TFT.

(f) Response time depends on the temperature.( In Lower temperature, it becomes longer)

SAMSUNG Confidential

SAMSUNG Confidential

MODEL

LSC460HN05-W

Doc. No

Page

23 / 30

9.4 Operation condition guide

(a) The LCD product shall be operated under normal conditions.
The normal condition is defined as below;

- Temperature : 20±15℃

- Humidity : 55±20%

- Display pattern : continually changing pattern (Not stationary)

(b) If the product will be used under extreme conditions such as under the high temperature, humidity,

display patterns or the operation time etc.., it is strongly recommended to contact SDC for the
advice about the application of engineering . Otherwise, its reliability and the function may not be
guaranteed. Extreme conditions are commonly found at airports, transit stations, banks, stock
markets, and controlling systems.

9.5 Others

(a) The ultra-violet ray filter is necessary for the outdoor operation.

(b) Avoid the condensation of water which may result in the improper operation of product or the

disconnection of electrode.

(c) Do not exceed the limit on the absolute maximum rating. (For example, the supply voltage

variation, the input voltage variation, the variation in content of parts and environmental
temperature, and so on) If not, panel may be damaged.

(d) If the module keeps displaying the same pattern for a long period of time, the image may be

remained to the screen. To avoid the image sticking, it is recommended to use a screen saver.

(e) This Panel has its circuitry of PCB's on the rear side, so it should be handled carefully in order for a

force not to be applied.

(f) Please contact the SDC in advance when the same pattern is displayed for a long time

SAMSUNG Confidential

MODEL

LSC460HN05-W

Doc. No

Page

24 / 30

10. Special precautions

10.1 Lists to be cautious when executing the design process

No.

Component

Expected cause

1

Upholding part for

panel

Prevent the panel from breaking by assigning gaps between the panel and the upholding part for panel on the drawing
for the upholding part for panel.
Refer to the (a), (b), (c) of 3-1 for the design of BLU.

2

The shape of the

upholding part for

panel

Design the upholding part for panel to fit to the panel appropriately when designing the BLU since the shape of the
upholding part for panel may damage the panel.
Refer to the (a), (b), (c) of 3-1 for the design of BLU.

3

The edge of

upholding part for

panel

Design the edge of panel to have a sufficient space with the upholding part for panel when designing the BLU since the
edge of the upholding part for panel may damage the panel when assembling the panel and BLU.
Refer to the (a), (b), (c) of 3-1 for the design of BLU.

4

Upholding part for

panel

Place the upholding part for the panel in order for the shape of mold, which contacts with the panel not to interfere with
the area of panel.
Refer to the (a), (b), (c) of 3-1 for the design of BLU.

5

Drive IC

Design the BLU in order for the COF not to contain the lead crack resulted from the tensioned COF created when the
product is twisted if the space between the D-IC COF and the middle mold isn't sufficient.
Refer to the (a), (b), (c),(d),(e),(f), and (g)of 3-2 for the design of BLU.

6

Drive IC

Design the BLU in order for the product not to contain the lead crack resulted from the tensioned COF caused under the
condition, which the product is twisted by fixing the source PCB.
Refer to the (a), (b), (c),(d),(e),(f), and (g)of 3-2 for the design of BLU.

7

IC

component

1) The temperature of each part of product suggested by our company and the second vendor shall meet the standard
of temperature, which is recommended not to be exceeded by our company when the product is affected under the
various temperature ranges.
Apply over 1mm long separation distance stated in the safety standard between the electric part and each conductor.
(Apply the rated separation distance when insulating.)

8

Thermal pad

Apply the thermal pad in a designated size to the product as a measure to lower the temperature of heat in order for
each part to use the rated temperature.

9

POL

The surrounding area of the POL shall be treated with an electrification treatment since the external ESD may cause a
phenomenon, which the POL is coming off.
In addition, the GND portion of source PBA shall be grounded.

10

PBA

The GND portion of each PBA shall be contacted with the GND portion of BLU.
Refer to the (a) and (b) of 3-3 for the design of BLU.

11

Circuit

The standardized approval from the client is required since the EMI is executed by a client.
Our company can only measure the reference since the client measures the BLU.

12

The height of

component

Design the BLU with considering the maximum height of parts, which our company suggests.

13

Between the FFC

and the C-PBA

Design the instrument with considering the length between the FFC and the control PBA.
(The marginal minimum length of 5mm or 8mm is required.)

14

Panel

The surface temperature of panel shall be maintained within 0℃ and 45℃ when the external ambient temperature is at
25℃. (Design the BLU with considering the increase of the temperature in the panel by the LED, CCFL, and etc.)

15

Aging

Recommend to age for over 1 hour at least in the state, which the product is driving initially to stabilize the characteristic
of the initial TFT.

16

The attachment of

gasket

The additional confirmation by our company is required If the attachment of gasket to the S-PBA of our company is
required.(To fix the S-PBA or the EMI)

17

Drive IC

Design the top chassis and the driver IC to be contacted by placing the shape of emboss inside the top chassis as a
measure to prevent the driver IC from heating. The size of emboss shall be designed in larger size than the size of IC
inside the film of the driver IC.
Refer to the (a), (b), (c),(d),(e),(f), and (g)of 3-2 for the design of BLU.

18

The prohibited

bandwidth

Design the BLU in order for the BLU not to interfere with the area, where the control PBA and the source PBA are
located densely according to the drawing for the BLU from our company.

19

S-PBA

The material, which contacts with the bottom side of S-PBA which has a pattern shall be non-conducting material or
shall be insulated.

SAMSUNG Confidential

MODEL

LSC460HN05-W

Doc. No

Page

25 / 30

4. FFC cable ( Material Code : 3809-002658, 51pin 44mm)

SAMSUNG Confidential

MODEL

LSC460HN05-W

Doc. No

Page

26 / 30

Appendix4

Packing Information

MODEL

LSC460HN05-W

Doc. No

Page

27 / 30

1. Panel Kit Packing

Item

Dimension

Weight

Q’ty / PLT

Total Weight

W x L x H (mm)

g

pcs

Kg

Packing Tray

1170 x 820 x117

2566

10

226.01

Pallet

1200 x 1000 x 150

19000

1

Panel

-

2350

70

Tray Top

1170 x 820 x 40

1450

1

Cushion Pad

1038 x 686.4 x 3.5

100

80

Silica gel

-

40

60

Paper Box

1184 x 834 x 1095

5000

1

Stack Layer

max

2

pallet

Total Size

1200 x 1000 x 1245

-

SAMSUNG Confidential

Note) The Cushion PAD is worked out for antistatic device.

SAMSUNG Confidential

MODEL

LSC460HN05-W

Doc. No

Page

28 / 30

2. Panel Kit Marking & Others

A nameplate bearing followed by is affixed to a shipped product at the specified
location on each product.
(1) Cell Label

SAMSUNG Confidential

MODEL

LSC460HN05-W

Doc. No

Page

29 / 30

Appendix5

Mechanical Information

MODEL

LSC460HN05-W

Doc. No

Page

30 / 30

1. Mechanical Information

Item

Specification

unit

Notes

Min

Typ

Max

Cell size
(TFT glass)

H - 1036.08

-

mm

V - 591.40

-

T

660

700

740

μm

Cell size
(CF glass)

H - 1030.88

-

mm

V - 588.7

-

T

660

700

740

μm

Polarizer size
(TFT side)

H

1028.68

1028.88

1029.08

mm

V

586.05

586.25

586.45

T

208

248

288

μm

Polarizer size
(CF side)

H

1029.08

1029.28

1029.48

mm

V

586.05

586.25

586.45

T

213

253

293

μm

Surface hardness of
polarizer

2H -

Warp of Cell Ass’y

-1

+1

mm

(1)

2.

SAMSUNG Confidential

Note (1) Measurement Method
a. Measurement Timing : After OLB Process at SDC Line
b. Measure a gap on surface plate by using thickness gauge.
Measure 4point(a,b,c,d) as Fig 1.