Samsung LN55C750, LN46C750 User Manual

Quick Setup Guide

AV IN 2

(HDD)

USB1

USB2

(

HDD)

HDMI IN 4

AV IN 2

(HDD)

USB1

USB2

(

HDD)

HDMI IN 4

AV IN 2

(HDD)

USB1

USB2

(

HDD)

HDMI IN 4

Congratulations on the purchase of your new Samsung TV. Read this setup guide to get your TV up and running quickly.

1-800-SAMSUNG (1-800-726-7864)

STOP

Please do not return this u nit.

If you hav e problems operati ng your

TV, call:

1-800-SAMS UNG (1-800-726-78 64)

For web su pport please visi t:

www.samsung.com /support

Getting Started

Step 1 :

Follow the steps below to connect the TV to the stand.

Make sure to distinguish between the front and back of the Stand and Guide

✎

Stand when assembling them.

Make sure that at least two people lift and move the LCD TV.

✎

Stand the product up and fasten the screws. If you fasten the screws with the LCD

✎

TV placed down, it may lean to one side.

Install the Stand

Stand

Screw

Samsung Electronics America, Inc. 105 Challenger Road Ridgeﬁeld Park, NJ 07660-0511 Samsung Electronics Canada Inc. 55 Standish Court Mississauga, Ontario L5R 4B2 Call Center hours of operation: Mon-Sun, 9:00 AM -12 AM EST. To register this product, visit:

www.samsung.com/register.

Guide Stand

Bottom View

Top View

Step 4 :

Connect External Devices

Connecting an AV device (Blu-ray player, cable/satellite box, etc.)

For the very best picture quality, select HD signal sources and use HDMI cables and

connections. Note that many digital cable programs are not in HD. Check with your video provider to ensure your are receiving HD signals.

The HDMI connection carries digital video and audio.

Audio/Video connection (480i only)

Using an Audio/Video Cable

VIDEO OUT

VCR / DVD / Blu-ray player / Cable Box / Satellite receiver

AUDIO OUT

Lowest Quality Connection

VCR

When connecting to ✎AV IN 1 on the back of your TV,

attach the video cable (yellow) to the green jack next to

the AV IN 1 label. The jack will not match the color of the video cable (yellow).

HD connection (up to 1080p)

Using an HDMI Cable

HDMI OUT

DVD / Blu-Ray player / HD Cable Box / HD Satellite receiver (STB)

Device

Best Connection

HD connection (up to 1080p)

Using an DVI to HDMI Cable

DVI OUT

AUDIO OUT

Device

DVD / Blu-Ray player / Cable Box /

Satellite receiver (STB)

Very Good Connection

Component connection (up to 1080p)

Using a Component Cable

AUDIO OUT

VCR / DVD / Blu-ray player / Cable Box / Satellite receiver

COMPONENT OUT

Good Connection

Device

Connecting an audio device

Connect your TV to your Home Theater or other audio

device to enjoy enhanced sound quality.

Connecting a PC

Connect your TV to a PC to use it as a Monitor.

Analog Audio connection

Using an Audio Cable

AUDIO IN

Ampliﬁer / DVD Home Theater

Device

Digital Audio connection

Using an Optical Cable

OPTICAL

Digital Audio System

HD connection

Using an HDMI Cable

AUDIO OUT

DVI OUT

Using an D-Sub Cable

PC OUT

AUDIO OUT

Front

Rear

Step 2 :

Install the Batteries into the Remote

To install batteries into your remote control, follow these steps:

1. Lift the cover on the back of the remote upward

as shown in the ﬁgure to the right.

2. Install two AAA batteries.

Make sure to match the + and - ends of

✎

the batteries to the diagram in the battery compartment.

3. Replace the cover.

Step 3 :

Power Input

Connect Power and Antenna or Cable

Use a 75 ohm (round) cable.

Connect ANT IN to:

• Wall cable jack or

• VHF/UHF Antenna or

• Cable or Satellite box Ant or Cable Out

Make sure the AC power cord is plugged in securely to the wall outlet and the TV.

Step 5 :

Run Plug & Play

When you turn on your TV for the ﬁrst time, it automatically launches the Plug & Play function. With Plug & Play, you can select the On Screen Display language,

set the clock mode, and launch the TV’s channel memorizing process. It also displays connection instructions similar to those in this guide.

To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow buttons on your remote. To make a selection, press the ENTERE button. To skip a screen, press the MENU button.

To turn on your TV, press the POWER button on the remote or press the

POWER button on the TV. To run Plug & Play, follow these steps:

Plug & Play

Sel ect Lan guage o f the O SD.

Lan guage : English

1. On the Language screen, select the language for the On Screen Display

(OSD) using your remote control, and then press ENTERE button. The Home Use screen appears.

2. Select Home Use, and then press ENTERE button. If you select Store

Demo, the TV will reset your picture and audio settings every 30 minutes. After

you press ENTERE button, the Antenna Source screen appears.

3. If your TV is only attached to an antenna, select Air. If your TV is only attached to cable and you have no cable box, select Cable. If your TV is attached to an antenna and cable with no box, select Auto. When done, press ENTERE button on your remote. The Select Cable System screen appears.

IMPORTANT:

3 through 5. After

If your TV is attached to a cable or satellite box, skip Steps

Plug & Play

according to the directions for your cable or satellite box.

4. If your TV is attached to a cable system and you have no cable box, you must select your cable system type. If you have Digital cable, you must select the cable system type for both Analog and Digital.

English

Español

Français

Move E Enter

is complete, set your TV to Channel 3 or 4,

After you have selected the cable system type, select Start, and then press the ENTERE button on your remote.

Most cable systems are Standard ✎(STD) systems. If you are not sure about what kind of cable system you have, contact your cable company.

5. The TV memorizes the available channels. This process can take up to 45 minutes. After the TV has memorized the channels, the Clock Mode screen appears.

6. Choose the Clock Mode. Select Auto if you have a digital channel in your area. Select Manual if you don’t, or if you have a cable or satellite box. When done, press ENTERE button. The Daylight Savings screen appears.

If you select ✎Manual, the clock setting screen appears.

7. Select the Daylight Saving Time setting: Off, On, or Auto, and then press

ENTERE button.

8. After the time zone screen, The connection method for best HD screen quality

is displayed. Press Right arrow button on your remote to view each screen in succession. Press the BLUE button to skip this section.

9. The Enjoy your TV screen appears. and then press ENTERE button.

Basic Functions

Changing the Screen Size

Your TV has several screen size options, each designed to work best with speciﬁc types of video input. If you have a cable box or satellite receiver, it may have its own set of screen sizes as well.

To change the screen size, press the P.SIZE button on your remote. The ﬁrst time you press it, your TV displays the current setting. Thereafter, each time you press the P.SIZE button, you change the size of the picture on the screen.

The following sizes are available:

16:9 Wide screen

Wide Fit

Zoom 1

4:3 Standard screen

Zoom 2

Screen Fit

Screen Fit ✎ displays a full HD picture covering the entire screen with no cutoff

on any side. It is only available when your TV inputs an HDMI (720p, 1080i, 1080p), Component (1080i, 1080p), or DTV (over-the-air 1080i) signal.

Changing the Picture Mode

Your TV has four preset Picture Modes with factory adjusted settings, each

designed to give you an excellent picture under speciﬁc conditions.

The Picture Modes are listed and described in the table below:

Mode Description

Dynamic

Standard For a bright, detailed picture in a normally lit room.

Natural For a comfortable, easy-on-the-eyes picture in a normally lit room.

Movie For a studio quality cinema picture in a dimly lit or dark room.

To change the Picture Mode, follow these steps:

1. With the TV on, press the TOOLS button on your remote. The Tools menu appears.

2. Using the ▲ or ▼ on your remote, select Picture mode.

3. On the Picture Mode menu, use the ◄ or ► on your remote to select the Picture Mode you want.

4. Press the EXIT button to exit the menu.

Brightens picture. For a vibrant, enhanced image in brightly lit or

sunny room.

English - 1

CONTENTINTERNET

MEDIA.P

Y A HOO!

FA V . CH

Remote Control Buttons and Functions:

This is a special remote control for the visually impaired persons and has Braille points on the Power, Channel, Volume buttons.

✎

Turns the TV on and off.

Press to switch between the sources (Blu-ray player,

cable box, DVD player, etc.) connected to your TV.

Press number buttons for direct access to channels.

Press to select additional digital channels broadcast

by the same station. For example, to select channel

54-3, press 54, press -, and then press 3.

Adjusts the volume.

Displays the channel list on the screen.

Displays the Content View, which includes Channel

List, Internet@TV, Media Play, AllShare and 3D.

Quickly selects frequently used functions.

Selects the on-screen menu items and changes the

values seen on the menu.

Return to the previous menu.

Colored buttons for use in the Channel List,

Internet@TV, Media Play menu, etc.

Use these buttons in the Media Play and Anynet+ modes.

( : Controls recording on Samsung recorders with the

Anynet+ feature)

Selecting a Source

To watch a movie on your Blu-ray player or watch your favorite TV show, you must select the correct

source. A source is a device, such as a Blu-ray/ DVD player, a cable/satellite box, antenna or a

cable TV input. Sources can be connected to your TV through the HDMI, DVI, Component, Composite, or D-sub connections, or through the Antenna or Cable In connections.

To view the signal from a source connected to the HDMI, DVI, Component, Composite, or D-sub jack, press the SOURCE button on your remote. Each time you press the SOURCE button, you change to a different source.

Viewing the On Screen Menus

To view the On Screen Menus, follow these steps:

1. With the power on, press the MENU button

on your remote. The main menu appears. The menu’s left side has the following menu options: Picture, Sound, Channel,

Setup, Input, Application, and Support.

2. Press the ▲ or ▼ button on your remote to

select a menu option, and then press the

ENTERE button.

3. When done using the menu, press the EXIT button on your remote to exit.

Turns the remote control light on and off. When on, the buttons become illuminated for a moment when pressed. (Using the remote control with this button set to off will reduce the battery usage time.)

Return to the previous channel.

Cuts off the sound temporarily.

Change channels.

If your TV is attached to a cable or satellite box, you change

✎

the channel using the box’s remote.

Displays the main on-screen menu.

Link to various internet services.

Press to display information on the TV screen.

Exits the menu.

MEDIA.P: Views Media Play. YAHOO!: Runs Yahoo widget!

3D: Sets the 3D mode. FAV.CH: Displays Favorite Channel Lists on the screen.

P.SIZE: Choose the picture size. CC: Controls the caption decoder.

Changing Channels and Adjusting the Volume

You can change the channel and adjust the volume by using the CH and VOL buttons on the remote. You can also change the channels by pressing the

buttons on the front

Remote control sensor

Power Indicator

panel of your TV and adjust the

volume by pressing the

buttons.

Setting the Clock

Before you can use your TV’s On/Off Timer, you must set the clock. To set the clock, follow these steps:

1. Turn on your TV.

2. Using your remote, press the

MENU button on your remote.

Then, select Setup → Time.

Month Day Year

3. Select Clock Mode, and then

press the ENTERE button. Set Clock Mode to Manual.

Select Auto if you have a digital

✎

channel in your area and are

Hour Minute am/pm

not using a cable/sat box.

4. Select Clock Set, and then press the ENTERE button. The Clock Set screen appears.

5. Using the number buttons on your remote, enter the Month, Day, Year, Hour, and Minute. Use the ◄ or ► button to move between entry ﬁelds.

6. Press the RETURN button on your remote when done.

Clock Set

-- -- ----

-- -- --

Move U Adjust

Enter

Return

Connecting a USB Device for Media Play

You can enjoy photo, music, and movie ﬁles stored on a USB device by connecting it to the TV and using the Media Play feature. To connect a USB device for Media Play, follow these steps:

1. Turn on your TV.

2. Connect a USB device

containing photo, music and/or

movie ﬁles to the USB1 (HDD)

MediaPlay

Videos

or USB2 jack on the side of the T V.

3. When the Application selection screen appears,

press the ENTERE button on your remote to select Media

SUM

Change Device

Play (USB).

Connecting to a Local Area Network

To enjoy watching streaming content from online providers such as You Tube and

Blockbuster, you must follow the steps below to connect the TV to your network.

TV Side Panel

USB Drive

View Devices E Enter R Return

Network Connection - Wired

There are two main ways to connect your TV to your network using cable, depending on your network setup. They are illustrated below:

The Modem Port on the Wall

The LAN Port on the Wall

External Modem

(ADSL / VDSL / Cable TV)

LAN Cable

LAN CableModem Cable

TV Rear Panel

Conﬁguring the Network Connection - Wired

Most home networks use the Dynamic Host Conﬁguration Protocol (DHCP) to conﬁgure network connections. Home networks that support DHCP automatically provide the IP address, subnet mask, gateway, and DNS values your TV needs to access the Internet so you don’t have to enter them manually.

To conﬁgure your network connection for a network that uses DHCP, follow these steps:

1. Connect your TV to your network

as shown in one of the illustrations above.

2. Turn on your TV, press the MENU button on your remote, and then select Setup → Network.

3. Set the Network Type to Wired if it

Internet Protocol Setup : Auto

IP Address :

Subnet Mask :

Gateway :

DNS : Auto

DNS Server :

is not already set to Wired.

4. Select Network Setup. The Network Setup screen appears.

5. On the Network Setup menu, set Internet Protocol Setup and DNS to Auto. Auto acquires and enters the necessary internet values automatically.

6. Select Network Test to check Internet connectivity.

Some networks are Static IP networks. If your network is a Static IP

✎

network, you can not use DHCP to conﬁgure the network connection. Instead, you must enter the IP Address, Subnet Mask, Gateway, and

DNS Server manually. For instructions explaining how to congure a

Static IP network, see your user’s manual.

Network Setup

Move

Enter

►

Return

Network Connection - Wireless

You can connect your TV to your LAN through a standard wireless router or modem. To connect wirelessly, you must ﬁrst attach a Samsung Wireless LAN Adapter (WIS09ABGN, WIS09ABGN2, WIS10ABGN - sold separately) to either the USB1

(HDD) or USB2 port on the back of your TV. See the illustration below.

TV Side Panel

The LAN Port on

the Wall

Wireless IP sharer

(AP having DHCP Server)

Samsung Wireless

LAN Adapter

LAN Cable

Samsung Wireless

LAN Adapter

Samsung’s Wireless LAN adapter supports the IEEE 802.11A, IEEE 802.11B, IEEE

802.11G, and IEEE 802.11N wireless communication protocols. For your TV to

connect to your network, the wireless router or modem you use must also support one of these protocols. The fastest of these protocols is IEEE 802.11N.

Most wireless network systems incorporate a security system that requires devices that access the network through an access point or AP (typically a wireless modem or router) to transmit an encrypted security code called an access key.

For regular connections, your TV is compatible with the following security protocols:

• Authentication Mode: OPEN, SHARED, WPAPSK, WPA2PSK

• Encryption Type: WEP, TKIP, AES

Conﬁguring the Network Connection - Wireless

The instructions below are for networks that use the Dynamic Host Conﬁguration Protocol (DHCP) to conﬁgure network connections automatically. If your have a Static IP network, see your user’s manual for conﬁguration instructions.

To conﬁgure your network connection for a network that uses DHCP, follow these steps:

1. Connect your TV to your network as

shown in the illustrations above.

2. Turn on your TV, press the

MENU button on your remote, and the

select Setup → Network.

3. Set the Network Type to Wireless if it is not already set to Wireless.

4. Select Network Setup. The Network

Select a network : Not Selected

Internet Protocol Setup : Auto

IP Address Subnet Mask Gateway

DNS : Auto

DNS Server

Network Setup

Move

Enter

►

Return

Setup screen appears.

5. On the Network Setup menu, select an AP(Access Point) and ad hoc network. if you have selected network with a security key, the Security Key screen appears.

6. Enter the Security Key using the numbers on the remote, and then press the Blue

button on your remote.

If your network uses WEP security encryption, 0~9 and A~F will be available

✎

on the Security Key screen. Use the Direction button on your remote to move to the characters and the enter key to select them.

7. On the Network Setup menu, set Internet Protocol Setup and DNS to Auto. The Auto acquires and enters the necessary internet values

automatically.

8. Select Network Test to check internet connectivity.

For more information, see your user’s manual.

✎

Starting Internet@TV

To view the On Screen Menus, follow these steps:

1. Turn on your TV, press the MENU button on your remote, then select Application → Content View.

2. Press the ◄ or ► button to select Internet@TV, and the

ENTERE button. The USER

TERMS and PRIVACY POLICY windows appears, then select Yes.

3. Follow the directions on your

screen to set up Internet@TV. For detailed instructions, see your Owner’s Manual.

For best ✎Internet@TV results, your broadband company should provide sustained download speeds of 3.5 mb/sec or more.

Recommended

My Applications by Date 1/1

SettingsSamsung Apps

Mark as Favorite

Sort by R Return

BN68-02617A-00

English - 2