Samsung LE22A455, LE22A457 User Manual

Contact SAMSUNG WORLDWIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.

Country

AUSTRIA 0800-SAMSUNG (726-7864) www.samsung.com/at BELGIUM 0032 (0)2 201 24 18 www.samsung.com/be

CZECH REPUBLIC

DENMARK 70 70 19 70 www.samsung.com/dk EIRE 0818 717 100 www.samsung.com/ie FINLAND 030-6227 515 www.samsung.com/

FRANCE

GERMANY 01805 - SAMSUNG (726-7864) (€ 0,14/Min) www.samsung.com HUNGARY 06-80-SAMSUNG (726-7864) www.samsung.com ITALIA 800-SAMSUNG (726-7864) www.samsung.com LUXEMBURG 0035 (0)2 261 03 710 www.samsung.com/be NETHERLANDS 0900-SAMSUNG (726-7864) (€ 0,10/Min) www.samsung.com/nl NORWAY 815-56 480 www.samsung.com/no

POLAND

PORTUGAL 80820-SAMSUNG (726-7864) www.samsung.com/pt SLOVAKIA 0800-SAMSUNG (726-7864) www.samsung.com/sk SPAIN 902 10 11 30 www.samsung.com SWEDEN 0771-400 200 www.samsung.com/se SWITZERLAND 0800-SAMSUNG (726-7864) www.samsung.com/ch U.K 0845 SAMSUNG (7267864) www.samsung.com TURKEY 444 77 11 www.samsung.com ESTONIA 800-7267 www.samsung.ee LATVIA 800-7267 www.samsung.com/lv LITHUANIA 8-800-77777 www.samsung.lt KAZAHSTAN 8-10-800-500-55-500 www.samsung.kz KYRGYZSTAN 00-800-500-55-500 RUSSIA 8-800-555-55-55 www.samsung.ru TADJIKISTAN 8-10-800-500-55-500 UKRAINE 8-800-502-0000 www.samsung.com UZBEKISTAN 8-10-800-500-55-500 www.samsung.uz

Customer Care Centre

844 000 844 www.samsung.com/cz

Distributor pro Českou republiku: Samsung Zrt., česka organizační složka Vyskočilova 4, 14000 Praha 4

3260 SAMSUNG (€ 0,15/Min) 08 25 08 65 65 (€ 0,15/Min)

0 801 801 881 022-607-93-33

Web Site

www.samsung.com

www.samsung.com/pl

LCD TV

user manual

BN68-01424Q-00

imagine the possibilities

Thank you for purchasing this Samsung product. To receive more complete service, please register your product at

www.samsung.com/global/register

Model Serial No.

This product is only applicable to Finnish, Swedish and Danish broadcasts. Broadcasts are not supported in other countries.

Contact SAMSUNG WORLDWIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.(See back cover for more information)

Precautions When Displaying a Still Image

A still image may cause permanent damage to the TV screen.

• Do not display a still image on the LCD panel for more than 2 hours as it can cause screen image retention. This image retention is also known as "screen burn". To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.

• Watching the LCD TV in 4:3 format for a long period of time may leave traces of

effect to the screen. Damages caused by the above effect are not covered by the Warranty.

• Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.

borders displayed on the left, right and center of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause a similar

Contents

CONNECTING AND PREPARING YOUR TV

List of Parts ........................................................ 2



Installing the Stand ............................................. 2



Installing the Wall Mount Kit ............................... 2



Viewing the Control Panel .................................. 3



Viewing the Connection Panel ........................... 4



Viewing the Remote Control ............................... 6



Installing Batteries in the Remote Control .......... 7



Switching On and Off ......................................... 7



Placing Your Television in Standby Mode........... 7



Viewing the Menus ............................................. 8



Using the TOOLS Button .................................... 8



Plug & Play ......................................................... 9



SETTING THE CHANNELS

Storing Channels Automatically ....................... 10



Storing Channels Manually ...............................11



Adding / Locking Channels .............................. 12



Sorting the Stored Channels ............................ 13



Assigning Channels Names ............................. 13



Fine Tuning Channel Reception ....................... 14



SETTING THE PICTURE

Changing the Picture Standard ........................ 15



Adjusting the Custom Picture ........................... 16



Resetting the Picture Settings to the Factory



Defaults ............................................................ 16

Changing the Picture Options .......................... 17



SETTING THE SOUND

Sound Features ................................................ 19



Selecting the Sound Mode ............................... 20



Connecting Headphones (Sold separately) ..... 20



SETTING THE TIME

Setting and Displaying the Current Time .......... 21



Setting the Sleep Timer .................................... 21



Switching the Television On and Off Automatically



FUNCTION DESCRIPTION

Choosing Your Language ................................. 22



Melody / Energy Saving .................................. 23



Selecting the Source ........................................ 24



Editing the Input Source Names ...................... 24



... 22

USING THE DTV FEATURE

Previewing the DTV Menu System .................. 25



Selecting the Country ....................................... 26



Updating the Channel List Automatically .......... 27



Updating the Channel List Manually ................ 28



Editing Your Favourite Channels ...................... 29



Selecting Channel List ..................................... 31



Displaying Programme Information .................. 31



Viewing the EPG (Electronic



Programme Guide) Information ........................ 32

Using the Scheduled List ................................. 33



Setting the Default Guide ................................. 33



Viewing All Channels and Favourite Channels 34



Adjusting the Menu Transparency .................... 34



Setting up the Parental Lock ............................ 35



Setting the Subtitle ........................................... 36



Setting the Subtitle Mode ................................. 36



Selecting the Audio Format .............................. 36



Selecting the Audio Description ....................... 37



Viewing Product Information ............................ 37



Checking the Signal Information ...................... 38



Upgrading the Software ................................... 38



Viewing Common Interface .............................. 39



Selecting the CI (Common Interface) Menu ..... 39



Resetting .......................................................... 40



Selecting the Preferred Language



(Subtitle, Audio or Teletext) .............................. 40

Preference ........................................................ 41



SETTING THE PC

Setting up Your PC Software



(Based on Windows XP) .................................. 42

Display Modes .................................................. 42



Setting up the TV with your PC ........................ 43



RECOMMENDATIONS FOR USE

Teletext Feature ............................................... 44



Using the Anti-Theft KENSINGTON LOCK



(depending on the model) .....................................45

Securing the TV to the Wall .............................. 46



Troubleshooting: Before Contacting Service



Personnel ......................................................... 47

Technical and Environmental Specications ... 48



English

Symbol Press Note One-Touch

Button

English - 1

List of Parts

Please make sure the following items are included with your LCD TV. If any items are missing, contact your dealer.

M4XL16

Remote Control &

Batteries (AAA x 2)

♦ Owner's Instructions ♦ Warranty card ♦ Safety Guide ♦ Registration Cards

Warranty card / Safety Guide /

➣ ➣

The stand and stand screw may not be included depending on the model.

Power Cord Cover-Bottom Stand Screw X 4 Stand

Registration Cards (Not available in all locations)

Cleaning Cloth

Installing the Stand

1. Connect your LCD TV and the stand.

Two or more people should carry the TV.

➣

Make sure to distinguish between the front and back of the stand when assembling them.

➣

2. Fasten two screws at position 1 and then fasten two screw at position 2.

Stand the product up and fasten the screws. If you fasten the screws with the LCD TV placed

➣

down, it may lean to one side. The stand is installed for models with the screen size of 37 inch and above.

➣

Installing the Wall Mount Kit

Wall mount items (sold separately) allow you to mount the TV on the wall. For detailed information on installing the wall mount, see the instructions provided with the Wall Mount items. Contact a technician for assistance when installing the wall mounted bracket. Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the TV on your own.

Do not install your Wall Mount Kit while your TV is turned on. It may result in personal injury due to electric shock.

Remove the stand and cover the bottom hole with a

➣

cap and fasten with two screws.

English - 2

Viewing the Control Panel

788

The product colour and shape may vary depending on the model.

Side Panel buttons

1 SOURCE Toggles between all the available input

sources (TV, Ext., AV, Component, PC, HDMI, DTV). In the on-screen menu, use this button as you use the ENTER button on the remote control.

2 MENU Press to see an on-screen menu of your TV’s features.

3 Press to decrease or increase the volume. In the on-screen menu, use the buttons as you use the ◄ and ► buttons on the remote control.

4 Press to change channels. In the on-screen

menu, use the buttons as you use the ▲ and ▼ buttons on the remote control. (Without the Remote Control, you can turn on the TV by using the Channel buttons.)

English - 3

(Power)

Press to turn the TV on and off. 6 Remote Control Sensor

Aim the remote control towards this spot on the TV.

7 Power Indicator Blinks and turns off when the power is on and lights up in stand-by mode.

8 Speakers

Viewing the Connection Panel

2 43 5

789

[TV Rear Panel]

Power Input

The product colour and shape may vary depending on the model.

➣

Whenever you connect an external device to your TV, make sure that power on the unit is turned off.

➣ ➣

When connecting an external device, match the colour of the connection terminal to the cable.

1 EXT

Connector

EXT

-Inputs or outputs for external devices, such as VCR, DVD, video game device or video disc players.

DVI IN [HDMI/DVI IN]

Supports connections between HDMI-connection-enabled AV devices (Set-Top Boxes, DVD players)

No additional Audio connection is needed for an HDMI to HDMI connection.

➣

What is HDMI?

“High Denition Multimedia interface” allows the transmission of high denition digital video data and

Video Audio (L/R) RGB Video + Audio (L/R)

Input Output

O O O

Only TV or DTV output is available.

[TV Side Panel]

multiple channels of digital audio. The HDMI/DVI terminal supports DVI connection to an extended device with the appropriate cable

(not supplied). The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP (High Bandwidth Digital Copy Protection) coding feature installed, and supports multi

- channel digital audio.

DVI IN [R-AUDIO-L]

DVI audio outputs for external devices.

Supported modes for HDMI/DVI and Component

➣

HDMI/DVI 50Hz HDMI/DVI 60Hz

Component O O O O O O

3 SERVICE

Connector for SERVICE only.

4 PC IN [PC] / [AUDIO]

Connect to the video and audio output jack on your PC.

480i 480p 576i 576p 720p 1080i

X X X O O O X O X X O O

English - 4

5 ANT IN To view television channels correctly, a signal must be received by the set from one of the following

sources:

An outdoor aerial / A cable television network / A satellite network

6 COMMON INTERFACE Slot

When CI Card isn’t inserted in some channels, "Scrambled

Signal" is displayed on the screen.

The pairing information containing a telephone number, CI Card ID, Host ID and other information will be displayed in about 2~3 minutes. If an error message is displayed, please contact your service provider.

When the channel information conguration has nished, the

message "Updating Completed" is displayed, indicating that the channel list is now updated.

You must obtain a CI Card from a local cable service provider.

➣

Remove the CI Card by carefully pulling it out with your hands since dropping the CI Card may cause damage to it.

➣

Insert the CI-Card in the direction marked on it.

➣

The place of the COMMON INTERFACE Slot may be different depending on its model.

7 Headphones jack

Headphone may be connected to the headphone output on your set. While the head phone is

connected, the sound from the built-in speakers will be disabled.

AV IN [VIDEO]/[R-AUDIO-L]

Connect RCA cable to an appropriate external A/V device such as VCR, DVD or Camcorder.

Connect RCA audio cables to [R-AUDIO-L] on your set and the other ends to corresponding audio

out connectors on the A/V device.

9 DIGITAL AUDIO OUT (OPTICAL)

Connect to a Digital Audio Component.

When the HDMI IN jacks are connected, the DIGITAL AUDIO OUT (OPTICAL) jack on the TV

➣

outputs 2 channel audio only. If you want to hear 5.1 channel audio, connect the Optical jack on

the DVD player or Cable/Satellite Box directly to an Amplier or Home Theater, not the TV.

0 COMPONENT IN

Connect component video cables (optional) to component connector ("PR", "PB", "Y") on the rear of

your set and the other ends to corresponding component video out connectors on the DTV or DVD. If you wish to connect both the Set-Top Box and DTV (or DVD), you should connect the Set-Top Box to

the DTV (or DVD) and connect the DTV (or DVD) to component connector ("P

The P

R, PB and Y connectors on your component devices (DTV or DVD) are sometimes labeled Y, B-Y

and R-Y or Y, Cb and Cr.

Connect RCA audio cables (optional) to [R - AUDIO - L] on the rear of your set and the other ends

R", "PB", "Y") on your set.

to corresponding audio out connectors on the DTV or DVD.

! KENSINGTON LOCK (depending on the model)

The Kensington lock (optional) is a device used to physically x the system when used in a public place.

If you want to use a locking device, contact the dealer where you purchased the TV.

The location of the kensington lock may be different depending on its model.

English - 5

TOOLS

Viewing the Remote Control

1 Television Standby button 2

Selects the TV and DTV

mode directly 3 Number buttons for direct

channel access

One/Two-digit channel selection

5 +: Volume increase

: Volume decrease

6 Temporary sound switch-off 7 Use to quickly select

frequently used functions.

Use to see information on

the current broadcast 9 Colour buttons :

Use these buttons in the

Channel list, etc.

Electronic Program Guide

(EPG) display

@ Available source selection # Previous channel $ P

: Next channel

P : Previous channel

Returns to the previous

^ Control the cursor in the menu & Exit the on-screen menu * Picture size selection ( Displays the main on-screen

) Displays the Channel List on

screen

Digital subtitle display

Teletext Functions

2 Exit from the teletext display 7 Teletext size selection 8 Teletext reveal 9 Fastext topic selection 0

Alternately select Teletext,

Double, or Mix.

! Teletext store @

Teletext mode selection

(LIST/FLOF)

# Teletext sub page $

P : Teletext next page

P : Teletext previous page

% Teletext hold & Teletext cancel ( Teletext index

The performance of the remote control may be affected by bright light.

➣

English - 6

Installing Batteries in the Remote Control

1. Lift the cover at the back of the remote control upward as shown in the

figure.

2. Install two AAA size batteries.

Make sure to match the "+" and "–" ends of the batteries with the

➣

diagram inside the compartment.

3. Replace the cover.

➣

Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a long time.

If the remote control doesn’t work, check the following:

➣

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power outage, or is the power cord unplugged?

5. Is there a special uorescent light or neon sign nearby?

Switching On and Off

The mains lead is attached to the rear of your set.

1. Plug the mains lead into an appropriate socket.

The standby indicator lights up on your set.

➣

2. Press the button on your set.

➣

You also can press the POWER button or the TV/DTV button on the remote control to turn the TV on. The channel that you were watching last is reselected automatically.

➣

3. Press the numeric button (0~9) or channel up/down ( / ) button on the remote control or

button on your set.

When you switch the set on for the very rst time, you will be asked to choose language in which the

➣

menus are to be displayed.

4. To switch your set off, press the POWER button again.

Placing Your Television in Standby Mode

Your set can be placed in standby mode in order to reduce the power consumption. The standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).

Press the POWER button on the remote control.

The screen is turned off and a red standby indicator appears on your set.

➣

2. To switch your set back on, simply press the POWER , numeric buttons (0~9), TV/DTV button or channel up/down ( / ) button again.

➣

Do not leave your set in standby mode for long periods of time (when you are away on holiday, for example). It is best to unplug the set from the mains and aerial.

English - 7

TOOLS

Viewing the Menus

TOOLS

1. With the power on, press the MENU button.

The main menu appears on the screen. The menu’ s left side has icons: Picture, Sound, Channel, Setup, Input, Digital Menu.

2. Press the ▲ or ▼ button to select one of the icons. Then press the ENTER button to access the icon’s sub-

menu.

3. Press the EXIT button to exit.

The on-screen menus disappear from the screen after about one minute.

Using the TOOLS Button

You can use the TOOLS button to select your frequently used functions quickly and easily. The “Tools” menu change depending on which external input mode you are viewing.

Press the TOOLS button.

The “Tools” menu will appear.

2. Press the ▲ or ▼ button to select a menu.

3. Press the ▲/▼/◄/►/ENTER buttons to display, change, or

use the selected items. For a more detailed description of each function, refer to the corresponding page.

• Picture Mode, see page 15

• Sound Mode, see page 19

• Sleep Timer, see page 21

• SRS TS XT, see page 19

• Energy Saving, see page 23

• Dual l-ll, see page 20

• Auto Adjustment, see page 43

Mode : Standard  Backlight 7 Contrast 95 Brightness 45 Sharpness 50 Colour 50

Tint G 50 R 50

Picture Options  Reset : OK 

Move Enter Return

Picture Mode ◄ Standard ►

Sound Mode : Custom Sleep Timer : Off SRS TS XT : Off Energy Saving : Off Dual l-ll : Mono

Move Adjust Exit

Picture

Tools

English - 8

Plug & Play

When the TV is initially powered on, several basic settings proceed automatically and subsequently. The following settings are available.

Any functions related to Digital TV (DVB) will only work in

countries or areas where DVB-T (MPEG2) digital terrestrial signals are broadcasted. Please confirm with your local dealer if you can receive DVB-T signals. Although this TV set follows the DVB-T specification, maintaining compatibility with the future coming DVB-T digital terrestrial broadcasts is not guaranteed. Several functions may not be available in some countries.

This product is only applicable to Finnish, Swedish and Danish broadcasts. Broadcasts are not

supported in other countries.

1. Press the POWER button on the remote control. The message "Start Plug & Play." is displayed with "OK" selected.

2. Select the appropriate language by pressing the ▲ or ▼ button. Press the ENTER button to confirm your choice.

3. Press the ◄ or ► button to select “Store Demo” or “Home Use”, then the ENTER button. We recommend setting the TV to "Home Use" mode for the best picture in your home

environment. "Store Demo" mode is only intended for use in retail environments. If the unit is accidentally set to “Store Demo” mode and you want to return to “Home Use”

(Standard): Press the Volume button on the TV. When the volume OSD is displayed, press and hold the MENU button on the TV for 5 seconds

4. The message "Check antenna input." is displayed with "OK" selected. Press the ENTER button. Please check that the antenna cable is connected correctly.

5. Select the appropriate country by pressing the ▲ or ▼ button. Press the ENTER button to confirm your choice.

6. The “Auto Store” menu is displayed with the “Start” selected. Press the ENTER button. Press the ENTER button at any time to interrupt the memorization process. The channel search will start and end automatically.

The DTV channel scan menu appears.

♦ If the country is set to “Others”

“Clock Set” screen appears when searching for the analog channel is finished.

If the country is set to “Finland”

♦

Press the

♦

If the country is set to “Sweden”, or “Denmark”

Press the ▲ or ▼ button to select “Cable” or “Aerial”. Press the

ENTER

button to select “Start”.

ENTER

Aerial: scanning for aerial services Cable: scanning for cable services

For detailed descriptions about DTV channel update, refer to page 28 of this manual. If the DTV channel is updated, the Source in the source list of the Input menu is automatically changed to DTV.

After all the available channels are stored, the “Clock Set” menu appears.

8. Press the ENTER button. Select the "Month", "Day", "Year", "Hour", or "Min" by pressing the ◄ or ► button. Set the "Month", "Day", "Year", "Hour", or "Min" by pressing the ▲ or ▼ button. You can also set the “Month”, “Day”, “Year”, “Hour” and "Min" by pressing the number buttons on

the remote control.

Plug & Play

Start Plug & Play.

Enter

button.

English - 9

9. Press the ENTER button to confirm your setting. The message “Enjoy your viewing” is displayed.

When you have finished, press the

ENTER button.

Even if the ENTER button is not pressed, the message will automatically disappear after

several seconds.

 Language  Country  Auto Store  Clock Set

: Select your language.

: Select your country.

: Automatically scans for and stores channels available in the local area.

: Sets the current time for the TV clock.

If you want to reset this feature...

Press the MENU button to display the menu.

Press the ▲ or ▼ button to select "Setup" then press the

ENTER button.

Plug & Play  Language : English  Time  Melody : Off  Energy Saving : Off 

Setup

2. Press the ENTER button again, to select "Plug & Play".

For further details on setting up options, refer to the page 9.

The “Plug & Play” feature is only available in the TV mode.

➣

Move Enter Return

Storing Channels Automatically

You can scan for the frequency ranges available to you (and availability depends on your country). Automatically allocated programme numbers may not correspond to actual or desired programme numbers. However, you can sort numbers manually and clear any channels you do not wish to watch.

Country : Finland  Auto Store  Manual Store  Channel Manager  Sort  Name  Fine Tune 

1. Press the MENU button to display the menu.

Press the ▲ or ▼ button to select "Channel", then press the

ENTER button.

Move Enter Return

2. Press the ENTER button to select "Country".

3. Select the appropriate country by pressing the ▲ or ▼ button. Press the ENTER button to confirm your choice.

➣

Even though you have changed the country setting in this menu, the country setting for DTV is not changed. (Refer to page 26)

4. Press the ▲ or ▼ button to select "Auto Store", then press the ENTER button.

5. Press the ENTER button.

The TV will begin memorizing all of the available channels.

➣

Press the

➣

ENTER button at any time to interrupt the memorization process and return to the

"Channel" menu.

6. After all the available channels are stored, the "Sort" menu appears. (refer to page 13)

Channel

English - 10

Storing Channels Manually

Not available in DTV or external input mode.

You can store television channels, including those received via cable networks. When storing channels manually, you can choose:

♦ Whether or not to store each of the channels found.

Country : Finland  Auto Store  Manual Store  Channel Manager  Sort  Name  Fine Tune 

Channel

♦ The programme number of each stored channel which you wish

to identify. Press the MENU button to display the menu.

Press the ▲ or ▼ button to select "Channel", then press the

ENTER button.

2. Press the ▲ or ▼ button to select "Manual Store", then press

the ENTER button.

3. Select the required option by pressing the ▲ or ▼ button,

Move Enter Return

Programme : P 1 Colour System : Auto  Sound System : BG  Channel : S 6 Search : 140 MHz Store : ?

Manual Store

then press the ENTER button.

4. When you are satisfied with your setting, press the

ENTER button.

Press the EXIT button to exit.

Move Enter Return

♦ Programme (Programme number to be assigned to a channel)

− Press the ▲ or ▼ button until you find the correct number. You can also select the channel number directly by pressing the numeric buttons (0~9).

Colour System: Auto/PAL/SECAM/NTSC4.43

♦

− Press the ▲ or ▼ button to select the required colour standard.

♦

Sound System: BG/DK/I/L

− Press the ▲ or ▼ button to select the required sound standard.

 Channel (When you know the number of the channel to be stored)

♦

− Press the ▲ or ▼ button to select C (Air channel) or S (Cable channel).

− Press the ► button, then press the ▲ or ▼ button to select the required number.

You can also select the channel number directly by pressing the numeric buttons (0~9). If there is abnormal sound or no sound, re-select the sound standard required.

 Search (When you do not know the channel numbers)

♦

− Press the ▲ or ▼ button to start the search.

− The tuner scans the frequency range until the first channel or the channel that you selected is

received on the screen.

♦

Store (When you store the channel and associated programme number)

− Set to "OK" by pressing the ENTER button.

Channel mode

− P (Programme mode): When completing tuning, the broadcasting stations in your area have been

assigned to position numbers from P00 to P99. You can select a channel by entering the position number in this mode.

− C (Air channel mode): You can select a channel by entering the assigned number to each air

broadcasting station in this mode.

− S (Cable channel mode): You can select a channel by entering the assigned number for each

cable channel in this mode.

English - 11

Adding / Locking Channels

TOOLS

Not available in DTV or external input mode.

➣

Using the Channel Manager, you can conveniently lock or add channels.

Press the MENU button to display the menu.

Press the ▲ or ▼ button to select "Channel", then press the

ENTER button.

2. Press the ▲ or ▼ button to select "Channel Manager", then press the ENTER button.

♦ Adding channels

Using the Channel List, you can add channels.

3. Select "Channel List" by pressing the ENTER button.

4. Move to the ( ) field by pressing the ▲, ▼, ◄ or ►

button, select a channel to be added, and press the

ENTER button to add the channel.

If you press the

➣

next to the channel disappears and the channel is not added.

" is active when "Child Lock" is selected to "On".

➣

♦ Locking channels

This feature allows you to prevent unauthorized users, such

as children, from watching unsuitable programmes by muting out video and audio.

5. Press the ▲ or ▼ button to select "Child Lock", then press the ENTER button.

6. Select "On" by pressing the ▲ or ▼ button, then press the ENTER button.

7. Press the ▲ or ▼ button to select "Channel List",

then press the ENTER button.

8. Move to the " " field by pressing the ▲, ▼, ◄ or ► button,

select a channel to be locked, and press the ENTER button.

If you press the

➣

next to the channel disappears and the channel lock is cancelled. A blue screen is displayed when "Child Lock" is activated.

➣

Press the EXIT button to exit.

Select "On" or "Off" in "Child Lock" to easily turn the

➣

channels which selected on " " to be active or inactive.

ENTER button again, the ( ) symbol

Country : Finland  Auto Store  Manual Store  Channel Manager  Sort  Name  Fine Tune 

Move Enter Return

Channel List  Child Lock : Off 

Move Enter Return

P 1 C3

Prog.

0 C-1 C3 2 BBC 1 3 C74 4 C75 5 C76 6 S3 7 S4 8 S6 9 S7

Add Lock

Move Enter

Page Return

Channel

Channel Manager

Channel List

1 / 10

You can select these options by simply pressing the CH LIST

button on the remote control.

English - 12

Sorting the Stored Channels

This operation allows you to change the programme numbers of the stored channels. This operation may be necessary after using the auto store.

Not available in DTV or external input mode.

➣

Press the MENU button to display the menu.

Press the ▲ or ▼ button to select "Channel", then press the

ENTER button.

2. Press the ▲ or ▼ button to select "Sort", then press the ENTER button.

3. Select the channel number that you wish to change by

pressing the ▲ or ▼ button. Press the

➣

ENTER

button. The selected channel number and name are moved to right side.

4. Select the number of the programme to which the channel is to

be moved by pressing the ▲ or ▼ button.

5. Press the

ENTER

button. The channel is moved to its new

position and all other channels are shifted accordingly.

6. Repeat steps 3 to 5 for another channel to be sorted.

7. Press the EXIT button to exit.

Assigning Channels Names

Channel names will be assigned automatically when channel information is broadcast. These names can be changed, allowing you to assign new names.

Not available in DTV or external input mode.

➣

1. Press the MENU button to display the menu. Press the ▲ or ▼ button to select "Channel", then press the

ENTER button.

2. Press the ▲ or ▼ button to select "Name", then press the ENTER button.

3. If necessary, select the channel to be assigned to a new

name by pressing the ▲ or ▼ button. Press the ENTER button.

➣

The selection bar is displayed around the name box.

4. To...

Select a letter, number or symbol Move on the next letter Move back the previous letter Confirm the name

➣

The following characters are available: Letters of the alphabet (A~Z) / Numbers (0~9) / Special characters (+, -, *, /, space)

5. Repeat steps 3 to 4 for each channel to be assigned to a new name.

6. Press the EXIT button to exit.

Then...

Press the ▲ or ▼ button Press the ► button Press the ◄ button

ENTER button

Press the

Country : Finland  Auto Store  Manual Store  Channel Manager  Sort  Name  Fine Tune 

Move Enter Return

Prog. Ch. Name  0 C-- ---- 1 C23 -----  2 S06 ---- 3 S07 ---- 4 S09 ---- 5 S12 ---- 6 S13 ---- 7 S14 ---- 8 S17 ---- 9 C21 ---- 

Move Enter Return

Country : Finland  Auto Store  Manual Store  Channel Manager  Sort  Name  Fine Tune 

Move Enter Return

Prog. Ch. Name  0 C-- -----

1 C23 -----

2 S06 ---- 3 S07 ---- 4 S09 ---- 5 S12 ---- 6 S13 ---- 7 S14 ---- 8 S17 ---- 9 C21 ---- 

Move Enter Return

Channel

Sort

Name

English - 13

+ 35 hidden pages