Samsung HW-Q60R operation manual

FULL MANUAL

HW-Q60R

Imagine the possibilities

Thank you fo r purchasing this Samsung product.

To receive more complete s ervice, please register

your product at www.samsung.com/register

SAFETY INFORMATION

SAFETY WARNINGS

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Refer to the table below for an explanation of symbols which may be on your Samsung product.

CAUTION

RISK OF E LECTRIC S HOCK.

DO NOT OP EN.

This symbol indicates that high voltage is present inside. It is dangerous to make any kind of contact with any internal part of this product.

This symbol indicates that this product has included important literature concerning operation and maintenance.

Class II product : This symbol indicates that it does not require a safety connection to electrical ear th (ground).

If this symbol is not present on a product with a power cord, the produc t MUST have a reliable connection to protective ear th (ground).

WARNING

• To reduce the risk of re or electric shock, do not expose this appliance to rain or moisture.

CAUTION

• TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

• This apparatus shall always be connected to a AC outlet with a protective grounding connection.

• To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.

• Do not expose this apparatus to dripping or

splashing. Do not put objects lled with

liquids, such as vases on the apparatus.

• To turn this apparatus off completely, you must pull the power plug out of the wall socket. Consequently, the power plug must be easily and readily accessible at all times.

AC voltage : This symbol indicates that the rated voltage marked with the symbol is AC voltage.

DC voltage : This symbol indicates that the rated voltage marked with the symbol is DC voltage.

Caution, Consult instructions for use : This symbol instructs the user to consult the user manual for further safety related information.

ENG - ii

PRECAUTIONS

1. Ensure that the AC power supply in your

house complies with the power

requirements listed on the identication

sticker located on the bottom of your product. Install your product horizontally, on a suitable base (furniture), with enough space around it for ventilation (7~10 cm). Make sure the ventilation slots are not

covered. Do not place the unit on ampliers

or other equipment which may become hot. This unit is designed for continuous use. To fully turn off the unit, disconnect the AC plug from the wall outlet. Unplug the unit if you intend to leave it unused for a long period of time.

2. During thunderstorms, disconnect the AC plug from the wall outlet. Voltage peaks due to lightning could damage the unit.

3. Do not expose the unit to direct sunlight or other heat sources. This could lead to overheating and cause the unit to malfunction.

4. Protect the product from moisture (i.e.

vases), and excess heat (e.g. a replace) or

equipment creating strong magnetic or

electric elds. Unplug the power cable from

the AC wall socket if the unit malfunctions. Your product is not intended for industrial use. It is for personal use only. Condensation may occur if your product has been stored in cold temperatures. If transporting the unit during the winter, wait approximately 2 hours until the unit has reached room temperature before using.

5. The battery used with this product contains chemicals that are harmful to the environment. Do not dispose of the battery in the general household trash. Do not expose the battery to excess heat, direct

sunlight, or re. Do not short circuit,

disassemble, or overheat the battery. Danger of explosion if the battery is replaced incorrectly. Replace only with the same or equivalent type.

ABOUT THIS MANUAL

The user manual has two parts: this simple paper USER MANUAL and a detailed FULL MANUAL you can download.

USER MANUAL

See this manual for safety instructions, product installation, components,

connections, and product specications.

FULL MANUAL

You can access the FULL MANUAL on Samsung’s on-line customer support centre by scanning the QR code. To see the manual on your PC or mobile device, download the manual in document format from Samsung’s website. (http://www.samsung.com/support)

Design and specications are subject to change

without prior notice.

ENG - iii

CONTENTS

01 Checking the Components 2

Inserting Batteries before using the Remote Control (AA batteries X 2) ------------------------- 2

02 Product Overview 3

Front Panel / Right Side Panel of the Soundbar

Bottom Panel of the Soundbar ------------------------- 4

-------------------------

03 Connecting the Soundbar 5

Connecting Electrical Power Connecting the Soundbar to the Subwoofer

– Automatic connection between the Subwoofer and the Soundbar – Manually connecting the Subwoofer if automatic connection fails

Connecting an SWA-8500S (Sold Separately) to your Soundbar

-------------------------

04 Connecting to your TV 10

Method 1. Connecting with a Cable

– Connecting using an Optical Cable – Connecting a TV using an HDMI Cable

Method 2. Connecting Wirelessly

– Connecting a TV via Bluetooth

-------------------------

05 Connecting an External Device 14

Connecting using an Optical or Analogue Audio (AUX) Cable Connecting using an HDMI Cable

-------------------------

5 6

6 7

14 15

06 Connecting a USB Storage Device 16

ENG - iv

07 Connecting a Mobile Device 18

Connecting via Bluetooth Using the Samsung Audio Remote App

– Installing the Samsung Audio Remote App – Launching the Samsung Audio Remote App

-------------------------

08 Using the Remote Control 22

How to Use the Remote Control Adjusting the Soundbar volume with a TV remote control Using the Hidden Buttons (Buttons with more than one function)

Output specications for the different sound effect modes

-------------------------

09 Installing the Wall Mount 27

Installation Precautions Wallmount Components

-------------------------

10 Installing the Holder Foot 29

Holder Foot Components

-------------------------

11 Software Update 30

Updating Procedure If UPDATE is not displayed

-------------------------

18 21

21 21

22 25 26 26

27 27

31 31

12 Troubleshooting 32

13 Licence 33

14 Open Source Licence Notice 33

15 Important Notes About Service 33

16 SpecicationsandGuide 34

Specications

-------------------------

ENG - v

01 CHECKING THE COMPONENTS

Soundbar Main Unit Subwoofer Remote Control / Batteries

1 2 3

PAIR

SOUND MODE

VOL WOOFER

SOUNDBAR

Power Cord

(Subwoofer)

Wall Mount Guide Holder-Screw

AC/DC Adapter

(Main Unit)

x 2 x 2

Holder Fo ot Holder-Support Screw (Holde r Foot)

Power Cord

(AC/DC Adapter)

x 2

Optic al Cable

x 2

Bracket-Wall Mount

(Wall Mount)

x 2

Screw

• For more information about the power supply and power consumption, refer to the label attached to the product. (Label: Bottom of the Soundbar Main Unit)

• The power components are labelled (1, 2, 3). For more information about power connections, see page 5.

• To purchase additional components or optional cables, contact a Samsung Service Centre or Samsung Customer Care.

• The appearance of the accessories may differ slightly from the illustrations above.

Inserting Batteries before using the Remote Control (AA batteries X 2)

Slide the battery cover in the direction of the arrow until it is completely removed. Insert 2 AA batteries (1.5V) oriented so that their polarity is correct. Slide the battery cover back into position.

ENG - 2

02 PRODUCT OVERVIEW

Front Panel / Right Side Panel of the Soundbar

Right Sid e of the Soundba r

Position the product so that the “Samsung Harman Kardon” logo is located on the top.

Display

󱂓

Displays the product’s status and current mode.

+/- (Volume) But ton

Adjusts the volume.

󱂔

• When adjusted, the volume level appears on the Soundbar ’s front display.

󱂔

󱂕

󱂖

󱂓

󱂕

󱂖

(Power) Button

Turns the power on and off.

(Source) But ton

Selects the source input mode.

Input mode Display

Optical Digital input D.IN

ARC (HDMI OUT) input D.IN  TV ARC (Auto conversion)

AUX input AUX

HDMI input HDMI

BLUETOOTH mode BT

USB mode USB

• To turn on “BT PAIRING” mode, change the source to “BT” mode, and then press and hold the (Source) button for more than 5 seconds.

• When you plug in the AC cord, the power button will begin working in 4 to 6 seconds.

• When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.

• If you want to enjoy sound only from the Soundbar, you must turn off the TV’s speakers in the Audio Setup menu of your TV. Refer to the owner’s manual supplied with your TV.

ENG - 3

Bottom Panel of the Soundbar

󱂓

󱂔

󱂕

USB (5V 0. 5A)

󱂓

Connect a USB device here to play music les on the USB device through the Soundbar.

AUX IN

󱂔

Connect to the Analogue output of an external device.

DIGITAL AUD IO IN (OPTIC AL)

󱂕

Connect to the digital (optical) output of an ex ternal device.

HDMI IN

Inputs digital video and audio signals simultaneously using an HDMI cable.

󱂖

Connect to the HDMI output of an external device.

USB (5V 0.5A)

AUX IN

DIGITAL AUDIO IN (OPTICAL)

USB (5V 0.5A)

AUX IN

DIGITAL AUDIO IN (OPTICAL)

HDMI IN

HDMI OUT (TV-ARC)

DC 24V

HDMI OUT

HDMI IN

(TV-ARC)

DC 24V

󱂖

󱂗

󱂘

HDMI OUT (TV-ARC)

󱂗

Connect to the HDMI (ARC) jack on a TV.

DC 24V (P ower Supply In)

󱂘

Connect the AC/DC power adapter.

• When disconnecting the power cable of the AC/DC power adaptor from a wall outlet, pull the plug. Do not pull the cable.

• Do not connect this unit or other components to an AC outlet until all connections between components are complete.

ENG - 4

03 CONNECTING THE SOUNDBAR

Connecting Electrical Power

Use the power components (1, 2 the following order:

, 3

) to connect the Subwoofer and Soundbar to an electrical outlet in

1 Connect the power cord to the Subwoofer. 2 Connect the power output cable to the power adapter, and then to the Soundbar.

Connect the power cord to a wall socket.

See the illustrations below.

• For more information about the required electrical power and power consumption, refer to the label attached to the product. (Label: Bottom of the Soundbar Main Unit)

3 Power Cord

Connecting

Electric al Power

2 AC/DC Adapter

POWER

Rear of Subwoofer

1 Power Cord

Connecting

Electric al Power

DC 24V

HDMI IN

HDMI OUT

(TV-ARC)

DC 24V

Bott om of the

Soundbar Main Unit

• Make sure to rest the AC/DC Adapter at on a table or the oor. If you place the AC/DC Adapter so that it is hanging with the AC cord input facing upwards, water or other foreign substances could enter the Adapter and cause the Adapter to malfunction.

ENG - 5

Connecting the Soundbar to the Subwoofer

When the subwoofer is connected, you can enjoy rich bass sound.

Automatic connection between the Subwoofer and the Soundbar

When you turn the power on after connecting the power cables to the Soundbar and subwoofer, the subwoofer is automatically connected to the Soundbar.

• When auto pairing is complete, the blue indicators at the rear of the subwoofer turn on.

LED Indicator Lights on the Rear of Subwoofer

LED Status Description Resolution

Successfully connected (normal operation)

Standby (with the Soundbar main unit turned off)

Connection failed

Check if the power cable attached to the main Soundbar unit is connected properly or wait about 5 minutes. If blinking persists, try manually connecting the subwoofer. See page 7.

Check if the power cable attached to the main Soundbar unit is connected properly.

Connect again. See the instructions for manual connection on page 7.

See the contact information for the Samsung Service Centre in this manual.

Blue

Red On

Red and

blue

Blinking Recovering the connection

Blinking Malfunction

ENG - 6

Manually connecting the Subwoofer if automatic connection fails

Before per forming the manual connection procedure below:

• Check whether the power cables for the Soundbar and subwoofer are connected properly.

• Make sure that the Soundbar is turned on.

1. Press and hold ID SET on the rear of the subwoofer for at least 5 seconds.

• The red indicator on the rear of the subwoofer turns off and the blue indicator blinks.

5 Sec

Rear of Subwoofer

2. Press and hold the Up button on the remote control for at least 5 seconds.

• The ID SET message appears on the display of the Soundbar for a moment, and then it disappears.

• The Soundbar will automatically power on when ID SET is complete.

PAIR

5 Sec

“Sam sung Harman Kard on” logo is on the top

3. Check if the LINK LED is solid blue (connection complete).

The LINK LED indicator stops blinking and glows a solid blue when a connection is established between the Soundbar and the Wireless Subwoofer.

Blue is On

ENG - 7

ID SET

NOTES

• Do not connect the power cord of this product or your TV to a wall outlet until all connections between components are complete.

• Before moving or installing this product, be sure to turn off the power and disconnect the power cord.

• If the main unit is powered off, the wireless subwoofer will go into stand-by mode and the STANDBY LED on the rear of the sub-woofer will turn red after blinking in blue several times.

• If you use a device that uses the same frequency (5.8GHz) as the Soundbar near the Soundbar, interference may cause some sound interruption.

• The maximum transmission distance of the main unit’s wireless signal is about 10 meters, but may vary depending on your operating environment. If a steel-concrete or metallic wall is between the main unit and the wireless subwoofer, the system may not operate at all because the wireless signal cannot penetrate metal.

PRECAUTIONS

• Wireless receiving antennas are built into the wireless subwoofer. Keep the unit away from water and moisture.

• For optimal listening performance, make sure that the area around the wireless subwoofer and the Wireless Receiver Module (sold separately) is clear of any obstructions.

Connecting an SWA-8500S (Sold Separately) to your Soundbar

Expand to true wireless surround sound by connecting the Samsung Wireless Rear Speaker Kit (SWA-8500S, sold separately) to your Soundbar.

1. Connect the Wireless Receiver Module to 2 Surround Speakers. – The speaker cables are colour coded.

SURROUND SPEAKERS OUT SPEAKER IMPEDANCE : 3Ω

SURROUND-LEFT SURROUND-RIGHT

SURROUND-LEFT

ID SET

ENG - 8

SURROUND-RIGHT

POWER

2. Check the standby status of the Wireless Receiver Module after plugging it into an electrical outlet.

POWER

ID SET

LINK

• The LINK LED indicator (blue LED) on the Wireless Receiver Module blinks. If the LED does not

blink, press the ID SET button on the back of the Wireless Receiver Module with a pen tip for 5~6 seconds until the LINK LED indicator blinks (in Blue). For more about the LED, please refer to the SWA-8500S user manual.

SURROUND SPEAKERS OUT SPEAKER IMPEDANCE : 3Ω

ID SET

5 Sec

STANDBY

LINK

Blue blinking

POWER

3. Press and hold the Up button on the remote control for at least 5 seconds.

• The ID SET message appears on the display of the Soundbar for a moment, and then it

disappears.

• The Soundbar will automatically power on when ID SET is complete.

PAIR

5 Sec

“Sam sung Harman Kard on” logo is on the top

CAUTION

• If your Soundbar was playing music when it connects to the SWA-8500S, you may hear some

stuttering from the woofer as the connection nalises.

4. Check if the LINK LED is solid blue (connection complete)

The LINK LED indicator stops blinking and

STANDBY

LINK

glows a solid blue when a connection is established between the Soundbar and the Wireless Receiver Module.

Blue is On

5. If the SWA-8500S is not connected, repeat the procedure from Step 2.

ENG - 9

ID SET

04 CONNECTING TO YOUR TV

Hear TV sound from your Soundbar through wired or wireless connections.

• When the Soundbar is connected to selected Samsung TVs, the Soundbar can be controlled using the TV’s remote control.

– This feature is supported by 2017 and later Samsung Smart TVs that support Bluetooth when

you connect the Soundbar to the TV using an optical cable.

– This function also allows you to use the TV menu to adjust the sound eld and various settings

as well as the volume and mute.

Method 1. Connecting with a Cable

When the audio in a broadcast is encoded in Dolby Digital and the “Digital Output Audio Format” on your TV is set to PCM, we recommend that you change the setting to Dolby Digital. When the setting on the TV is changed, you will experience better sound quality. (The TV menu may use different words for Dolby Digital and PCM depending on the TV manufacturer.)

Connecting using an Optical Cable

Bott om of the Soundba r

AUX IN

DIGITAL AUDIO IN (OPTICAL)

OPTICAL OUT

󱂓

Optic al Cable

󱂔

D.IN

1. Connect the DIGITAL AUDIO IN (OPTICAL) jack on the Soundbar to the OPTICAL OUT jack of the TV

with a digital optical cable.

2. Press the (Source) button on the right side panel or remote control, and then select the “D.IN” mode.

ENG - 10

Right Sid e of the Soundbar

Auto Power Link

Auto Power Link automatically turns on the Soundbar when the TV is turned on.

1. Connect the Soundbar and a TV with a digital optical cable.

2. Press the Left button on the remote control for 5 seconds to turn Auto Power

Link on or off.

• Auto Power Link is set to ON by default. (To turn off this function, hold the Left button on the remote for 5 seconds.)

• Depending on the connected device, Auto Power Link may not function.

• This function is only available in the “D.IN” mode.

Connecting a TV using an HDMI Cable

Connec t to the HDMI IN

(ARC) p ort of your T V.

󱂓

HDMI IN

(ARC)

Connec t to the HDMI OUT ( TV-ARC)

HDMI Cable

(not supplied)

port o f the Soundbar mai n unit.

󱂔

1. With the Soundbar and TV turned on, connect the HDMI cable (not supplied) as shown in the gure.

2. “TV ARC” appears in the display window of the Soundbar main unit and the Soundbar plays TV

sound.

• If TV sound is inaudible, press the (Source) button on the remote control or on the right side of the Soundbar to switch to “D.IN” mode. The screen displays “D.IN” and “TV ARC” in sequence, and TV sound is played.

• If “T V ARC” does not appear in the display window of the Soundbar main unit, conrm that the HDMI cable (not supplied) is connected to the correct port.

• Use the volume buttons on the TV’s remote control to change the volume on the Soundbar.

Bott om of the Soundba r

HDMI IN

HDMI OUT

(TV-ARC)

TV ARC

Right Sid e of the Soundbar

ENG - 11

NOTES

• HDMI is an interface that enables the digital transmission of video and audio data with just a single connector.

• If the TV provides an ARC port, connect the HDMI cable to the HDMI IN (ARC) port.

• We recommend you use a coreless HDMI cable if possible. If you use a cored HDMI cable, use one whose diameter is less than 14 mm.

• Anynet+ must be turned on.

• This function is not available if the HDMI cable does not support ARC.

Method 2. Connecting Wirelessly

Connecting a TV via Bluetooth

When a TV is connected using Bluetooth, you can hear stereo sound without the hassle of cabling.

• Only one TV can be connected at a time.

PAIR

The initial connection

1. Press the PAIR button on the remote control to enter the “BT PAIRING” mode.

(OR)

a. Press the (Source) button on the right side panel and then select “BT”.

“BT” changes to “BT READY” in a few seconds automatically if there is no Bluetooth device connected to the Soundbar.

b. When “BT READY” appears, press and hold the (Source) button on the right side panel

of the Soundbar for more than 5 seconds to display “BT PAIRING”.

2. Select Bluetooth mode on the TV. (For more information, see the TV’s manual.)

3. Select “[AV] Samsung Soundbar Q6R-Series” from the list on TV’s screen.

An available Soundbar is indicated with “Need Pairing ” or “Paired” on the TV’s Bluetooth device list. To connect the TV to the Soundbar, select the message, and then establish a connection.

• When the TV is connected, [TV Name] → “BT” appears on the Soundbar’s front display.

4. You can now hear TV sound from the Soundbar.

ENG - 12

If the device fails to connect

• If a previously connected Soundbar listing (e.g. “[ AV] Samsung Soundbar Q6R-Series”) appears in the list, delete it.

• Then repeat steps 1 through 3.

NOTE

• After you have connected the Soundbar to your TV the rst time, use the “BT READY” mode to reconnect.

Disconnecting the Soundbar from the TV

Press the (Source) button on the right side panel or on the remote control and switch to any mode but “BT”.

• Disconnecting takes time because the TV must receive a response from the Soundbar. (The time required may differ, depending on the TV model.)

• To cancel the automatic Bluetooth connection between the Soundbar and TV, press the p (Play/Pause) button on the remote control for 5 seconds with the Soundbar in “BT READY” status.

(Toggle On → Off)

What is the difference between BT READY and BT PAIRING?

• BT READY : In this mode, you can search for previously connected TVs or connect a previously connected mobile device to the Soundbar.

• BT PAIRING : In this mode, you can connect a new device to the Soundbar. (Press the PAIR button on the remote control or press and hold the (Source) button on the right side of the Soundbar for more than 5 seconds while the Soundbar is in “BT” mode.)

NOTES

• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.

• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the Soundbar and the Bluetooth device exceeds 10 meters.

• The Soundbar automatically turns off after 20 minutes in the Ready state.

• The Soundbar may not perform Bluetooth search or connection correctly under the following circumstances:

– If there is a strong electrical eld around the Soundbar. – If several Bluetooth devices are simultaneously paired with the Soundbar. – If the Bluetooth device is turned off, not in place, or malfunctions.

• Electronic devices may cause radio interference. Devices that generate electromagnetic waves must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.

ENG - 13

05 CONNECTING AN EXTERNAL DEVICE

Connect to an external device via a wired or wireless network to play the external device’s sound through the Soundbar.

Connecting using an Optical or Analogue Audio (AUX) Cable

BD / DVD play er / Set-top b ox / Game console

R L

- AUDIO -

Audio (AU X) Cable

(not supplied)

󱂓

USB (5V 0.5A)

AUX IN

DIGITAL AUDIO IN (OPTICAL)

Right Sid e of the Soundbar

󱂔

OPTICAL OUT

Optic al Cable

1 Audio (AUX) Cable

X Connect AUX IN (Audio) on the main unit to the AUDIO OUT jack of the Source Device using an

audio cable.

Y Select “AUX” mode by pressing the (Source) button on the right side panel or on the remote

control.

Bott om of the Soundba r

2 Optical Cable

X Connect DIGITAL AUDIO IN (OP TICAL) on the main unit to the OPTICAL OUT jack of the Source

Device using a digital optical cable.

Y Select “D.IN” mode by pressing the (Source) button on the right side panel or on the remote

control.

ENG - 14

Connecting using an HDMI Cable

Bott om of the Soundba r

External Dev ice

HDMI OUT

HDMI Cable

(not supplied)

󱂓

󱂔

HDMI IN

(ARC)

HDMI Cable

(not supplied)

󱂖

1. Connect an HDMI cable (not supplied) from the HDMI IN jack on the back of the product to the HDMI OUT jack on your digital device.

2. Connect an HDMI cable (not supplied) from the HDMI OUT (TV-ARC) jack on the back of the product to the HDMI IN jack on your TV.

3. Press the (Source) button on the right side panel or on the remote control, and then select “HDMI”.

4. “HDMI” mode is displayed on the Soundbar display panel and sound plays.

HDMI

HDMI IN

HDMI OUT

(TV-ARC)

Right Sid e of the Soundbar

󱂕

ENG - 15

06 CONNECTING A USB STORAGE DEVICE

You can play music les located on USB storage devices through the Soundbar.

DisplayUSB por t

USB (5V 0.5A)

AUX IN

DIGITAL AUDIO IN (OPTICAL)

HDMI IN

HDMI OUT (TV-ARC)

DC 24V

USB (5V 0.5A)

USB

Micro USB t o

USB adap ter Cable

(not supplied)

1. Connect a Micro USB to USB adapter cable with a male USB 2.0 Micro USB plug (Type B) on one

end and a standard female 2.0 USB jack (Type A) on the other end to the micro USB jack on your Soundbar.

• The Micro USB to USB adapter cable is sold separately. To purchase, contact a Samsung Service Centre or Samsung Customer Care.

2. Connect your USB device to the female end of the adapter cable.

3. Press the (Source) button on the right side panel or on the remote control, and then select “USB”.

4. “USB” appears in the display screen.

5. Play music les from the USB storage device through the Soundbar.

• The Soundbar automatically turns off (Auto Power Down) if no USB device has been connected for more than 20 minutes.

ENG - 16

File Format Type Compatibility list

Extension Codec Sampling Rate Bitrate

*.m p3 MPEG 1 Layer2 16kHz ~ 48kHz 80kbps~320kbps

MPEG 1 Layer3 16kHz ~ 48kHz 80kbps~320kbps

MPEG 2 Layer3 16kHz ~ 48kHz 80kbps~320kbps

MPEG 2.5 Layer3 16kHz ~ 48kHz 80kbps~320kbps

*.wma Wave_Format_MSAudio1 16kHz ~ 48kHz 56kbps~128kbps

Wave_Format_MSAudio2 16kHz ~ 48kHz 56kbps~128kbps

*.a ac AAC 16kHz ~ 96kHz 48kbps~320kbps

A A C-LC 16kHz ~ 96kHz

HE-AAC 24kHz ~ 96kHz

*.wav - 16kHz ~ 48kHz up to 3000kbps

*.o gg OGG 1.1.0 16kHz ~ 48kHz 50kbps~500kbps

128kbps~192kbps

5.1ch 3 20kbps

48kbps~64kbps

5.1ch 160kbp s

• If there are too many folders and les stored on the USB device, it may take the Soundbar some

time to access and play les.

ENG - 17

07 CONNECTING A MOBILE DEVICE

Connecting via Bluetooth

When a mobile device is connected using Bluetooth, you can hear stereo sound without the hassle of cabling.

• You cannot connect more than one Bluetooth device at a time.

PAIR

Bluetooth device

The initial connection

1. Press the PAIR button on the remote control to enter the “BT PAIRING” mode.

(OR)

a. Press the (Source) button on the right side panel and then select “BT”.

“BT” changes to “BT READY” in a few seconds automatically if there is no Bluetooth device connected to the Soundbar.

b. When “BT READY” appears, press and hold the (Source) button on the right side panel

of the Soundbar for more than 5 seconds to display “BT PAIRING”.

2. On your device, select “[AV] Samsung Soundbar Q6R-Series” from the list that appears.

• When the Soundbar is connected to the Bluetooth device, [Bluetooth Device Name] → “BT” appears in the front display.

3. Play music les from the device connected via Bluetooth through the Soundbar.

If the device fails to connect

• If a previously connected Soundbar listing (e.g. “[ AV] Samsung Soundbar Q6R-Series”) appears in the list, delete it.

• Then repeat steps 1 and 2.

NOTE

• After you have connected the Soundbar to your mobile device the rst time, use the “BT READY” mode to reconnect.

ENG - 18

What is the difference between BT READY and BT PAIRING?

• BT READY : In this mode, you can search for previously connected TVs or connect a previously connected mobile device to the Soundbar.

NOTES

• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.

• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the Soundbar and the Bluetooth device exceeds 10 meters.

• The Soundbar automatically turns off after 20 minutes in the Ready state.

• The Soundbar may not perform Bluetooth search or connection correctly under the following circumstances:

• Electronic devices may cause radio interference. Devices that generate electromagnetic waves must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.

• The Soundbar supports SBC data (44.1kHz, 48kHz).

• Connect only to a Bluetooth device that supports the A2DP (AV) function.

• You cannot connect the Soundbar to a Bluetooth device that supports only the HF (Hands Free) function.

• Once you have paired the Soundbar to a Bluetooth device, selecting “[AV] Samsung Soundbar Q6R-Series” from the device’s scanned devices list will automatically change the Soundbar to “BT” mode.

– Available only if the Soundbar is listed among the Bluetooth device’s paired devices.

(The Bluetooth device and the Soundbar must have been previously paired at least once.)

• The Soundbar will appear in the Bluetooth device’s searched devices list only when the Soundbar is displaying “BT READY”.

• The Soundbar cannot be paired to another Bluetooth device if already in Bluetooth mode and paired to a Bluetooth device.

Bluetooth Power On (SOUND MODE)

If a previously paired Bluetooth device tries to pair with the Soundbar when the Bluetooth Power On function is on and the Soundbar is turned off, the Soundbar turns on automatically.

1. Press and hold the SOUND MODE button for more than 5 seconds on the remote while the Soundbar is turned on.

2. “ON-BLUETOOTH POWER ” appears on the Soundbar’s display.

ENG - 19

Disconnecting the Bluetooth device from a Soundbar

You can disconnect a Bluetooth device from the Soundbar. For instructions, see the Bluetooth device’s user manual.

• The Soundbar will be disconnected.

• When the Soundbar is disconnected from the Bluetooth device, the Soundbar will display “BT DISCONNECTED” on the front display.

Disconnecting the Soundbar from the Bluetooth device

Press the (Source) button on the right side panel or on the remote control, and then change to any mode except “BT”.

• Disconnecting takes time because the Bluetooth device must receive a response from the Soundbar. (Disconnection time may differ, depending on the Bluetooth device)

• When the Soundbar is disconnected from the Bluetooth device, the Soundbar will display “BT DISCONNECTED” on the front display.

NOTES

• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the Soundbar and the Bluetooth device exceeds 10 meters.

• The Soundbar automatically turns off after 20 minutes in the Ready state.

More About Bluetooth

Bluetooth is a technology that enables Bluetooth-compliant devices to interconnect easily with each other using a short wireless connection.

• A Bluetooth device may cause noise or malfunction, depending on usage, if:

– A part of your body is in contact with the receiving/transmitting system of the Bluetooth

device or the Soundbar. – It is subject to electrical variation from obstructions caused by a wall, corner, or ofce partition. – It is exposed to electrical interference from same frequency-band devices including medical

equipment, microwave ovens, and wireless LANs.

• Pair the Soundbar with the Bluetooth device while they are close together.

• The further the distance between the Soundbar and Bluetooth device, the worse the quality is. If the distance exceeds the Bluetooth operational range, the connection is lost.

• In poor reception areas, the Bluetooth connection may not work properly.

• The Bluetooth connection only works when it is close to the unit. The connection will be automatically cut off if the Bluetooth device is out of range. Even within range, the sound quality may be degraded by obstacles such as walls or doors.

• This wireless device may cause electric interference during its operation.

ENG - 20

Using the Samsung Audio Remote App

Installing the Samsung Audio Remote App

To control the Soundbar with your smart device and the Samsung Audio Remote app, download the Samsung Audio Remote app from the Google Play store.

Market se arch : Samsung Au dio Remote

Launching the Samsung Audio Remote App

To launch and use the Samsung Audio Remote app, touch the Audio Remote icon on your smart device, and then follow the directions on the screen.

Audio Remote

• The Samsung Audio Remote app is only compatible with Android mobile phones and mobile devices running Android OS 3.0 or later.

ENG - 21

08 USING THE REMOTE CONTROL

PAIR

How to Use the Remote Control

󱂓

󱂔

󱂕

󱂖

PAIR

SOUND

MODE

VOL WOOFER

SOUNDBAR

󱂗

󱂘

󱂙

󱂚

󱂛

󱂜

󱂓

󱂔

󱂕

󱂖

SOUND MODE

Power

Source

Mute

SOUND

MODE

Turns the Soundbar on and off.

Press to select a source connected to the Soundbar.

• BT PAIRING mode To turn on “BT PAIRING” mode, change the source to “BT” mode, and then press and hold the (Sour ce) button for more than 5 seconds.

Press the (Mute) button to mute the sound. Press it again to unmute the sound.

You can selec t the desired sound effect by choosing STANDARD, SURROUND SOUND, GAME P RO, or ADAPTIVE SOUND. Select the “STANDARD” mode if you want to enjoy the original sound.

• DRC (Dynamic Rang e Control) Lets you apply dynamic range control to Dolby Digital tracks. Press and hold the SOUND MODE button while the Soundbar is powered off to turn DRC (Dynamic Range Control) on or off. With the DRC turned on, loud sound is reduced. (The sound may be distorted.)

• Bluetooth Power This feature automatically turns the Soundbar on when it receives a connection request from a previously connected TV or Bluetooth device. The set ting is On by

default.

– Press and hold the SOUND MODE

button for more than 5 seconds to turn off the Bluetooth Power function.

ENG - 22

󱂗

PAIR

Bluetooth

PAIR

Press the PAIR button. “BT PAIRING” appears in the Soundbar’s display. You can connec t the Soundbar to a new Bluetooth device in this mode by selecting the Soundbar from the Bluetooth device's search list.

󱂘

󱂙

Play / Pau se

Up/Down/ Left/Right

Press the p button to pause a music le temporarily. When you press the button again, the music le plays.

• Auto Power Down Function The unit turns off automatically in the following situations:

– In D.IN / HDMI / BT / USB Mode : If there is no audio signal for 20 minutes. – In AUX Mode :

– If the Audio (AUX) Cable is disconnected for 20 minutes. – If there is no KE Y input for 8 hours when the Audio (AUX) Cable is connec ted.

(The Auto Power Down function can be turned off only when the unit is in “AUX” mode.)

– To turn off Auto Power Down function while the unit is in “AUX” mode, press

and hold the p button for 5 seconds. “ON -AUTO POWER DO WN” / “OFF-

AUTO POW ER DOWN” appears on the display.

Press the indicated areas to select Up/Down/Left/Right.

Press Up/Down/Left /Right on the button to select or set functions.

• Repeat To use the Repeat function in “USB” mode, press the Up button.

• Music Skip Press the Right button to select the next music le. Press the Left button to select the

previous music le.

• Anynet+ / Auto P ower Link You can turn Anynet+ and Auto Power Link on or off. Anynet+ and Auto Power Link are turned on and turned of f by the Right and Left buttons respectively.

– Anynet+ : If the Soundbar is connected to a Samsung TV through an HDMI cable,

you can control your Soundbar with a Samsung TV remote control. Press and hold the Right but ton for 5 seconds to toggle Anynet+ ON and OFF.

– Auto Power Link : If the Soundbar is connected to your TV through a digital optical

cable, the Soundbar can automatically turn on when you turn on your TV. Press and hold the Left button for 5 seconds to toggle Auto Power Link ON and OFF.

– Anynet+ / Auto Power Link are set to ON by default.

• ID SET Press and hold the Up button for 5 seconds to complete ID SET (when connec ting to an accessary item).

ENG - 23

• Volume Restriction function

PAIR

SOUNDBAR

SOUND

MODE

PAIR

SOUND

MODE

VOL

WOOFER

SOUNDBAR

SOUND

MODE

VOL

WOOFER

SOUNDBAR

To protect your hearing, the Volume Restric tion function restricts the volume to 20 if you turn on the Soundbar when the volume is set higher than 20.

– The default value for the Volume Restric tion function is Off. You must turn it on to

activate it.

– When turned on, the Volume Restric tion function stays on even when the power is

turned off.

– To turn Volume Restric tion on or off, press and hold the Down button on the

remote control for 5 seconds. With Volume Restriction off, “ V FREE” appears on the front display. With the function on, “V LO CK” appears.

󱂚

󱂛

󱂜

Sound Control

WOOFER

VOL

You can selec t TREBLE, BASS, or AUDIO SYNC.

• To control the volume of the treble or bass sound, selec t TREBLE or BASS in Sound Settings, and then adjus t the volume between -6~+6 by using the Up/Down buttons.

• Press and hold the (Sound Control) but ton for about 5 seconds to adjust the sound for each frequency band. 150Hz, 300Hz, 600Hz, 1.2kHz, 2.5kHz, 5kHz, and 10kHz are selectable using the Left/Right buttons and each can be adjusted to a setting between

-6 to +6 using the Up/Down buttons.

• If the video on the T V and audio from the Soundbar are not synchronised, select AUDIO SYNC in Sound Settings, and then

set the audio delay between 0~300 milliseconds

using the Up/Down buttons. (Not available in “ USB” mode.)

• AUDIO SYNC is only suppor ted for some functions.

SOUND

MODE

WOOFER

VOL

SOUND

MODE

WOOFER

VOL

Push the WOOFER but ton up or down to adjust the volume of the subwoofer to -12 or between -6 to +6. To set the subwoofer volume level to 0, press the button.

SOUND

MODE

WOOFER

VOL

SOUND

MODE

WOOFER

VOL

Push the VOL button up or down to adjust the volume.

• Mute Press the VOL but ton to mute the sound. Press it again to unmute the sound.

ENG - 24

Adjusting the Soundbar volume

SOUNDBAR

with a TV remote control

If you have a Samsung TV, you can adjust the Soundbar’s volume using the IR remote control that came with your Samsung TV.

First use the TV menu to set the TV audio on your Samsung TV to external speakers, then use your Samsung remote to control the Soundbar’s volume. For more information, see the TV’s user manual. The default mode for this function is control by a Samsung TV remote. If your TV is not a Samsung TV, follow the directions below to change the settings of this function.

1. Turn Off the Soundbar.

BYE

2. If you do not want to use this function, push

up and hold the WOOFER button for 5 seconds repeatedly until “OFF-T V

REMOTE” appears in the display.

4. If you want to return the Soundbar to the

default mode (control by a Samsung TV remote), push up and hold the WOOFER button for 5 seconds repeatedly until “SAMSUNG-TV REMOTE” appears in the display.

SOUND

MODE

5 Sec

WOOFER

VOL

(Default mode)

SAMSUNG-TV REMOTE

– Each time you push the WOOFER button

up and hold it for 5 seconds, the mode switches in the following order: “SAMSUNG-TV REMOTE” (Default mode)

→ “OFF‑TV REMOTE” →

“ALL‑TV REMOTE”.

– This function may not be available,

depending on the remote control.

– Manufacturers supporting this function:

VIZIO, LG, Sony, Sharp, PHILIPS, PANASONIC, TOSHIBA, GRUNDIG, Hisense, RCA

SOUND

MODE

5 Sec

WOOFER

VOL

OFF-TV REMOTE

3. If you want to control the Soundbar with

your TV’s remote, push up and hold the

WOOFER button for 5 seconds repeatedly

until “ALL-TV REMOTE” appears in the display. Then, use your TV’s menu to select external speakers.

5 Sec

WOOFER

VOL

ALL-TV REMOTE

SOUND

MODE

ENG - 25

Using the Hidden Buttons (Buttons with more than one function)

Bluetooth

POWER

Hidden Button

Remote Control Button Function

WOOFER TV remote control On/Off (Standby) page 25

(Source)

p (Play / Pause)

Left Auto Power Link ON/OFF page 23

Right Anynet+ ON/OFF page 23

Up ID SET page 23

Down Volume restriction On/Off page 24

(Sound Control)

SOUND MODE

BT Pairing page 22

Auto Power Down On/Off

(AUX mode)

Initialise (Standby) page 31

BT Ready page 13

7 Band EQ page 24

DRC ON/OFF (Standby) page 22

Bluetooth Power page 22

Reference page

page 23

Outputspecicationsforthedifferentsoundeffectmodes

Output

SOUND

MODE

SOUND MODE

Effect Input

STANDARD

SURROUND

SOUND

GAME PRO

ADAPTIVE

SOUND

2.0 ch

5.1 ch 3.1 ch 5 .1 ch

2.0 ch

5.1 ch 5.1 ch 7.1 ch

2.0 ch

5.1 ch 5.1 ch 7.1 ch

2.0 ch

5.1 ch 5.1 ch 7.1 ch

Without Wireless Rear

Spea ker Kit

2.1 ch 4.1 ch

5.1 ch 7.1 c h

With Wireless Rear

Spea ker Kit

• The Samsung Wireless Rear Speaker Kit can be purchased separately. To purchase a Kit, contact the vendor you purchased the Soundbar from.

ENG - 26

+ 124 hidden pages