Samsung HT-Q45T-XAA User Manual
SAMSUNG ELECTRONICS AMERICA, INC.
COMPACT
DIGITAL AUDIO
SERVICE DIVISION
400 Valley Road, Suite 201
Mount Arlington, NJ 07856
1-800-SAMSUNG (1-800-726-7864)
www.samsung.com
Home Theater System with
5 Disc DVD Changer
HT-Q45
Instruction Manual
Safety Warnings Precautions
ENG
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LASER CLASE 1
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE REAR COVER.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Note to CATV system installer :
This reminder is provided to call the CATV system
installer’s attention to Section 820~40 of the NEC
which provides guidelines for proper grounding and,
in particular, specifies that the cable ground shall be
connected to the grounding system of the building,
as close to the point of cable entry as practical
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a CLASS 1
LASER product.
Use of controls, adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
CAUTION-INVISIBLE LASER RADIATION WHEN OPEN
AND INTERLOCKS DEFEATED, AVOID
EXPOSURE TO BEAM.
PREPARATION
Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. Install your
player horizontally, on a suitable base (furniture), with enough space around it for ventilation (3~4inches). Make sure the ventilation
slots are not covered. Do not stack anything on top of the player. Do not place the player on modules or other equipment which may
become hot. Before moving the player, ensure the disc tray is empty. This player is designed for continuous use. Switching off the
Home Theater to the stand-by mode does not disconnect the electrical supply. In order to disconnect the player completely from the
power
During thunderstorms, disconnect AC main plug from the
wall outlet.
Voltage peaks due to lightning could damage the unit.
Do not expose the unit to direct sunlight or other heat
sources.
This could lead to overheating and malfunction of the unit.
This symbol indicates that dangerous voltage which can cause electric shock is present inside
this unit.
This symbol alerts you to important operating and maintenance instructions accompanying
the unit.
Phones
WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
Protect the player from moisture(i.e. vases) , and excess heat
(e.g.fireplace) or equipment creating strong magnetic or electric fields
(i.e.speakers...). Disconnect the power cable from the AC supply if the
player malfunctions. Your player is not intended for industrial use.
Use of this product is for personal use only.
Condensation may occur if your player or disc has been stored in cold
temperatures.
If transporting the player during the winter, wait approximately 2 hours
until the unit has reached room temperature before using.
The batteries used with this product contain chemicals
that are harmful to the environment.
Do not dispose of batteries in the general household
trash.
12
ANTENNA
LEAD IN WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION. 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
Safety Instructions
ENG
READ INSTRUCTIONS
All the safety and operating instructions should be
read before the appliance is operated.
RETAIN INSTRUCTIONS
The safety and operating instructions should be
retained for future reference.
HEED WARNINGS
All warnings on the appliance and in the operating
instructions should be adhered to.
FOLLOW INSTRUCTIONS
All operating and use instructions should be
followed.
WATER AND MOISTURE
Do not use this video product near waterfor example, near a bathtub, wash bowl,
kitchen sink, or laundry tub, in a wet basement,
or near a swimming pool, and the like.
OVERLOADING
Do not overload wall outlets and extension cords as
this can result in the risk of fire
or electric shock.
VENTILATION
Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the
video product and to protect it from overheating
these openings must not be blocked or covered.
The openings should never be blocked
by placing the video product on a bed, sofa, rug, or
other similar surface. This video product
should never be placed near or over a radiator or
heat register.
This video product should not be placed
in a built-in installation such as a bookcase
or rack unless proper ventilation is provided
or the manufacturer's instructions have been followed.
POWER CORD PROTECTION
Power-supply cords should be routed so that
they are not likely to be walked on or pinched
by items placed upon or against them paying
particular attention to cords at plugs,
convenience receptacles, and the point where
they exit from the appliance.
CLEANING
Unplug this video product from the wall outlet
before cleaning. Do not use liquid cleaners
or aerosol cleaners. Use a damp cloth for cleaning.
LIGHTNING
For added protection of this video product
receiver during a lightning storm, or when
it is left unattended and unused for long
periods of time, unplug it from the wall outlet
and disconnect the antenna or cable system.
This will prevent damage to the video product
due to lightning and power-line surges.
OBJECT AND LIQUID ENTRY
Never push objects of any kind into this
product through openings as they may touch
dangerous voltage points or short-out parts
that could result in a fire or electric shock.
Never spill liquid of any kind on the video
product.
ACCESSORIES
Do not place this video product on an unstable cart,
stand, tripod, bracket, or table.
The video product may fall, causing serious injury to
a child or adult, and serious damage
to the appliance.
Use only with a cart, stand, tripod, bracket,
or table recommended by the manufacturer,
or sold with the video product. Any mounting
of the appliance should follow the manufacturer's
instructions and should use a mounting accessory
recommended by the manufacturer.
CART
An appliance and cart combination should be moved
with care. Quick stops, excessive force, and uneven
surfaces may cause the appliance and cart combination to overturn.
POWER SOURCES
This video product should be operated only from the
type of power source indicated
on the marking label. If you are not sure
of the type of supply to your home, consult your
appliance dealer or local power company.
For video products intended to be operated from battery power, or other sources, refer
to the operating instructions.
POWER LINES
An outside antenna system should not be located in
the vicinity of overhead power lines or other electric
light or power circuits,
or where it can fall into such power lines
or circuits. When installing an outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with
them might be fatal.
POLARIZATION
This video product is equipped with a polarized
alternating current line plug (a plug having one
blade wider than the other.) This plug will fit into the
power outlet only one way.
This is a safety feature. If you are unable
to insert the plug fully into the outlet, try reversing
plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
OUTDOOR ANTENNA GROUNDING
If an outside antenna is connected to the
•
antenna terminal, be sure the antenna system
is grounded so as to provide some protection
against voltage surges and built-up static
charges.
In the U.S.A section 810 of the National
•
Electrical Code, ANSI/NFPA No. 70-1984,
provides information with respect to proper
grounding of the mast and supporting
structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit,
connection to grounding electrodes, and
requirements for the grounding electrode.
See the figure below.
ATTACHMENTS
Do not use attachments not recommended
by the video product manufacturer as they may
cause hazards.
SERVICING
Do not attempt to service this product yourself
•
as opening or removing covers may expose
you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
•
the
REPLACEMENT PARTS
When replacement parts are required, be sure the
service technician has used replacement parts specified by the manufacturer or having the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.
SAFETY CHECK
Upon completion of any service or repairs
to this video product, ask the service technician to
perform safety checks to determine that the video
product is in proper operating condition.
DAMAGE REQUIRING SERVICE
Unplug this video product from the wall outlet
refer servicing to qualified service personnel
the following conditions.
a.
When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have
fallen into the video product.
c. If the video product has been exposed to rain
or water
d.
If the video product does not operate normally
by following the operating instructions.
Adjust only those controls that are covered
by the operating instructions as an improper
adjustment of other controls may result
in damage and will often require extensive
work by a qualified technician to restore
the video product to its normal operation.
e. If the video product has been dropped
or the cabinet has been damaged.
f. When the video product exhibits a distinct
change in performance - this indicates
a need for service.
HEAT
This video unit should be situated away from heat
sources such as radiators, stoves, or other products
(including modules) that produce heat.
and
under
PREPARATION
43
Features
Multi-Disc Playback & FM Tuner
The HT-Q45 combines the convenience of multi-disc playback capability, including
DVD-AUDIO, DVD-VIDEO, CD, MP3-CD, WMA-CD, DivX, CD-R/RW, and DVD-R/RW, with a
sophisticated FM tuner, all in a single player.
DVD-Audio compatible
Experience the super high-quality audio performance of DVD-Audio.
The on-board 24-bit/192kHz DAC enables this player to deliver exceptional sound quality in
terms of dynamic range, low-level resolution and high-frequency detail.
USB Host Play
You can enjoy media files such as pictures, movies and tunes saved in an MP3 player, digital camera or
USB memory by connecting the storage device to the USB port of the home theater.
Dolby Pro Logic II
Dolby Pro Logic II is a new form of multi-channel audio signal decoding technology that
improves upon existing Dolby Pro Logic.
Contents
PREPARATION
Safety Warnings .................................................................1
Precautions.........................................................................2
Safety Instructions..............................................................3
Features .............................................................................5
Notes on Discs ...................................................................7
Description..........................................................................9
CONNECTIONS
Connecting the Speakers ...................................................13
Connecting the optional Wireless Receiving Amplifier.......15
Connecting the Video Out to TV ........................................17
P.SCAN(Progressive Scan) Function .................................18
Connecting External Components......................................19
Connecting the FM Antenna...............................................20
Connecting an optional XM Satellite Radio Antenna .........20
ENG
PREPARATION
SETUP
Setting the Language .........................................................43
Setting TV Screen type ......................................................45
Setting Parental Controls (Rating Level)............................47
Setting the Password .........................................................48
Setting the Wallpaper .........................................................49
DVD Playback Mode ..........................................................51
Setting the Speaker Mode..................................................52
Setting the Delay Time.......................................................53
Setting the Test Tone..........................................................55
Setting the DRC (Dynamic Range Compression)..............56
Setting the Audio ...............................................................57
AV SYNC Setup .................................................................59
Sound Field (DSP)/EQ Function ........................................60
Dolby Pro Logic II Mode.....................................................61
Dolby Pro Logic II Effect.....................................................62
DTS (Digital Theater Systems)
DTS is an audio compression format developed by Digital Theater Systems Inc. It delivers
full-frequency 5.1 channel sound.
TV Screen Saver Function
The HT-Q45 automatically brightens and darkens your TV screen after 3 minutes in the stop mode.
The HT-Q45 automatically switches itself into the power saving mode after 20 minutes in the
screen saver mode.
Power Saving Function
The HT-Q45 automatically shuts itself off after 20 minutes in stop mode.
Customized TV Screen Display
The HT-Q45 allows you to select your favorite image during JPEG and DVD playback and set
it as your background wallpaper.
AV SYNC Function
Video may lag behind the audio if the unit is connected to a digital TV.
To compensate for this, you can adjust the audio delay time to sync up with the video.
Optional XM radio
Samsung ’s XM Ready Home Theater Systems give you the opportunity to enjoy America ’s
leading satellite radio service in CD-quality sound.
OPERATION
Before Using Your Home Theater ......................................21
Disc Playback.....................................................................23
Selecting a Disc in the Disc changer .................................24
MP3/WMA-CD Playback ....................................................25
Displaying Disc Information................................................26
JPEG File Playback............................................................27
DivX Playback ....................................................................29
Checking the Remaining Time ...........................................31
Fast/Slow Playback ............................................................32
Skipping Scenes/Songs......................................................32
Repeat Playback ................................................................33
A-B Repeat Playback .........................................................34
Step Function .....................................................................35
Angle Function....................................................................35
Zoom (Screen Enlarge) Function .......................................36
EZ VIEW Function..............................................................36
Bonus Group / Navigating Pages.......................................37
Selecting Audio/Subtitle Language.....................................38
Playing Media Files using the USB HOST feature.............39
Moving Directly to a Scene/Song .......................................41
Using Disc Menu ................................................................42
Using the Title Menu...........................................................42
RADIO OPERATION
Listening to Radio...............................................................63
Presetting Stations .............................................................64
Before Using XM Satellite Radio........................................65
Listening to XM Satellite Radio .........................................66
XM Display Mode ..............................................................67
XM Search Mode ...............................................................69
Presetting XM Satellite Radio.............................................70
MISCELLANEOUS
Convenient Functions.........................................................71
Operating a TV with the Remote Control ...........................73
Before Calling for Service...................................................75
Cautions on Handling and Storing Discs............................77
Language Code List ...........................................................78
USB Host Feature Supported Products .............................79
Specifications .....................................................................80
Optional Wireless receiver amplifier
Samsung ’s optional rear-channel wireless module does away with cables running between
your DVD receiver and rear-channel speakers. Instead,the rear speakers connect to a
compact wireless module that communicates with your DVD receiver.
65
V I D E O
1 6
~
Notes on Discs
ENG
DVD (Digital Versatile Disc) offers fantastic audio and video, thanks to Dolby Digital
surround sound and MPEG-2 video compression technology. Now you can enjoy these
realistic effects in the home, as if you were in a movie theater or concert hall.
DVD players and the discs are coded by region. These regional codes must match in order
for the disc to play. If the codes do not match, the disc will not play.
The Region Number for this player is given on the rear panel of the player.
(Your DVD player will only play DVDs that are labeled with identical region codes.)
Playable Discs
Disc Type Disc Size Max. Playing Time
DVD
AUDIO-CD
DivX
Mark (Logo)
V I D E O
COMPACT
DIGITAL AUDIO
Recorded Signals
Audio + Video
Audio
MPEG4
MP3
5"
3 1/2"
5"
3 1/2"
5"
3 1/2"
Approx. 240 min. (single-sided)
Approx. 480 min. (double-sided)
Approx. 80 min. (single-sided)
Approx. 160 min. (double-sided)
74 min.
20 min.
74 min.
20 min.
Do not use the following types of disc!
LD, CD-G, CD-I, CD-ROM and DVD-ROM discs cannot be played on this player.
•
If such discs are played, a "WRONG DISC FORMAT" message appears on the TV screen.
DVD discs purchased abroad may not play on this player.
•
If such discs are played, a "WRONG REGION CODE" message appears on the TV screen.
Copy Protection
Many DVD discs are encoded with copy protection. Because of this, you should only connect
•
your DVD player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy-protected DVD discs.
This product incorporates copyright protection technology that is protected by methods claims of certain
•
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and
is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
Disc Recording Format
This product does not support Secure (DRM) Media files.
CD-R Discs
Some CD-R discs may not be playable depending on the disc recording device (CD-Recorder or PC) and the
•
condition of the disc.
Use a 650MB/74 minute CD-R disc.
•
Do not use CD-R discs over 700MB/80 minute as they may not be played back.
Some CD-RW (Rewritable) media, may not be playable.
•
Only CD-Rs that are properly "closed" can be fully played. If the session is closed but the disc is left open, you
•
may not be able to fully play the disc.
CD-R MP3 Discs
Only CD-R discs with MP3 files in ISO 9660 or Joliet format can be played.
•
MP3 file names should be 8 characters or less in length and contain no blank spaces or special characters (. / = +).
•
Use discs recorded with a compression/decompression data rate greater than 128Kbps.
•
Only files with the ".mp3" and ".MP3" extensions can be played.
•
Only a consecutively written Multisession disc can be played. If there is a blank segment in the Multisession disc,
•
the disc can be played only up to the blank segment.
If the disc is not closed, it will take longer to begin playback and not all of the recorded files may be played.
•
For files encoded in Variable Bit Rate (VBR) format, i.e. files encoded in both low bit rate and high bit rate
•
(e.g., 32Kbps ~ 320Kbps), the sound may skip during playback.
A maximum of 500 tracks can be played per CD.
•
A maximum of 300 folders can be played per CD.
•
CD-R JPEG Discs
Only files with the ".jpeg" and ".JPEG" extensions can be played.
•
If the disc is not closed, it will take longer to start playing and not all of the recorded files may be played.
•
Only CD-R discs with JPEG files in ISO 9660 or Joliet format can be played.
•
JPEG file names should be 8 characters or less in length and contain no blank spaces or special characters (. / = +).
•
Only a consecutively written multisession disc can be played. If there is a blank segment in the multisession disc, the
•
disc can be played only up to the blank segment.
A maximum of 9,999 images can be stored on a single CD.
•
When playing a Kodak/Fuji Picture CD, only the JPEG files in the picture folder can be played.
•
Picture discs other than Kodak/Fuji Picture CDs may take longer to start playing or may not play at all.
•
CD-R/RW DivX Discs
Since this product only provides encoding formats authorized by DivX Networks, Inc., a DivX file created by the user
•
might not be played.
Software update for unsupported formats is not supported.
•
(Example: QPEL, GMC, resolution higher than 720 x 480 pixels, etc.)
Sections with high frame rate might not be played while playing a DivX file.
•
For more information about the formats authorized by DivX Networks, Inc., visit "www.divxnetworks.net".
•
87
PREPARATION
Description
ENG
—Front Panel—
Standby indicator
Power ( ) button
Disc Tray
Function button
Tuning Up & Skip ( ) buttons
Tuning Down & Skip ( ) buttons
Volume control
Headphone Jack
Play/Pause ( ) button
Stop ( ) button
Direct Play buttons
Open/
Close button
USB port
—Rear Panel—
External Audio Input Connectors
5.1 Channel Speaker
Cooling Fan
Output Terminals
Video Output Connector
Connect the TV's video input jacks
(VIDEO IN) to the VIDEO OUT connector.
TX Card Connector
XM Antenna Connector
PREPARATION
External Digital Optical
Input Connector
Use this to connect external equipment
capable of digital output.
FM Antenna Connector
COMPONENT VIDEO OUTPUT
Connectors
Connect a TV with component video inputs
to these jacks.
DOLBY DIGITAL indicator
LINEAR PCM indicator
P.SCAN
indicator
DTS
indicator
MPEG indicator
DVD AUDIO indicator
DOLBY PLll indicator
9
GROUP indicator
TITLE
indicator
DSP indicator
CHAPTER indicator
TRACK indicator
PROGRAM indicator
System Status Display
REPEAT indicator
FREQUENCY
STEREO indicator
TUNED indicator
RADIO
SPEAKER indicator
indicator
DISC(1~5)
indicator
Accessories
Remote Control
(AH59-01662G)
Video Cable
(AH39-40001V)
FM Antenna
(AH42-00021A)
User's Manual
(AH68-01880A)
10
Description
—Remote Control—
ENG
PREPARATION
Insert Remote Batteries
TV button
DVD Receiver button
POWER button
Number(0~9) buttons
REMAIN button
STEP button
SEARCH buttons
VOLUME button
MENU button
DVD button
AUX button
OPEN/CLOSE button
TV/VIDEO, DISC SKIP
CANCEL button
REPEAT button
Play/Pause button
Tuning Preset/CD Skip button
TUNING/CH button
MUTE button
RETURN button
Cursor/Enter button
FM/XM button
USB button
Stop button
Remove the battery
1
cover on the back of
the remote by pressing
down and sliding the
cover in the direction of
the arrow.
Caution
Follow these precautions to avoid leaking or cracking cells:
Place batteries in the remote control so they match the polarity:(+) to (+)and (–)to (–).
•
Use the correct type of batteries.Batteries that look similar may differ in voltage.
•
Always replace both batteries at the same time.
•
Do not expose batteries to heat or flame.
•
Insert two 1.5V AAA
2
batteries, paying
attention to the correct
polarities (+ and –).
Replace the battery
3
cover.
INFO button
PL II EFFECT button
PL II MODE button
FM/XM MEMORY, P.SCAN button
ZOOM button
SLEEP button
SLOW, MO/ST button
DIMMER button
11
XM SEARCH, AUDIO button
XM DISPLAY, SUB TITLE button
DSP/EQ button
TEST TONE button
SOUND EDIT button
DIGEST button
LOGO button
SLIDE MODE button
EZ VIEW button
Range of Operation of the Remote Control
The remote control can be used up to approximately 23 feet/7 meters in a straight line. It can also be
operated at a horizontal angle of up to 30° from the remote control sensor.
12
SRSL
C
L
SW
R
R
L
C
SR
SL
SW
Connecting the Speakers
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
ENG
Position of the Home Theater
Place it on a stand, cabinet shelf, or under the
•
TV stand.
Front Speakers
Place these speakers in front of your listening
•
position, facing inwards (about 45°) toward you.
Place the speakers so that their tweeters will be at
•
the same height as your ear.
Align the front face of the front speakers with the
•
front face of the center speaker or place them
slightly in front of the center speakers.
Center Speaker
It is best to install it at the same height as the front
•
speakers.
You can also install it directly over or under the TV.
•
Selecting the Listening Position
The listening position should be located about 2.5 to 3
times the distance of the TV's screen size away from the
TV. Example: For 32" TVs 2~2.4m (6~8 feet)
For 55" TVs 3.5~4m (11~13 feet)
Rear Speakers
Place these speakers behind your listening position.
•
If there isn't enough room, place these speakers so they face each
•
other.
Place them about 60 to 90cm (2 to 3feet) above your ear, facing
•
slightly downward.
Unlike the front and center speakers, the rear speakers are used
*
to handle mainly sound effects and sound will not come from
them all the time.
Subwoofer
The position of the subwoofer is not so critical.
•
Place it anywhere you like.
Rear Speaker (R)
Front Speaker (R)
Press and hold the terminal tab.
1
Insert the speaker cord.
2
Release your finger.
3
Caution
Do not let children play with or near the speakers.
•
They could get hurt if a speaker falls.
When connecting the speaker wires to the speakers,
•
make sure that the polarity (+/–) is correct.
Center Speaker
Subwoofer
12 3
Note
If you place a speaker near your TV set,
•
screen color may be distorted because of
the magnetic field generated by the
speaker. If this occurs, place the speaker
away from your TV set.
Red
Rear Speaker (L)
Front Speaker (L)
Black
CONNECTIONS
13
14
Connecting the optional Wireless Receiving Amplifier
To connect the rear speakers wirelessly, you have to additionally purchase the wireless receiving module and
TX card from your Samsung retailer.
Rear Speaker (L)
WIRELESS RECEIVER MODULE
Front Speaker (R)
Center Speaker
Rear Speaker (R)
Front Speaker (L)
Subwoofer
When you have purchased the wireless receiving module (SWA-3000)
Resetting Wireless Communication
Reset the system if a communication failure occurs, or if the Link indicator (blue LED) on the wireless receiver does
not light up and the "REAR CHK" message blinks on the main unit's display.
Reset the system while the main unit and the wireless receiver module (SWA-3000) are in Power Standby mode.
With the main unit turned off, press and
1
hold the remote control's REMAIN button
for 5 seconds.
Press the button until the POWER( ) indicator lights
•
up blue. (The indicator will turn off in 1 second.)
With the wireless receiver module
2
turned on, use a ball point pen or a pair
of tweezers to press the RESET button
on the back of the unit.
The Standby/On LED on the front panel of the
•
wireless receiver module blinks 2 times.
WIRELESS RECEIVER MODULE
ENG
CONNECTIONS
Connect the front, center and
1
subwoofer speakers, referring to page 14.
Insert the TX card into the TX card
2
connection port on the back of the
main unit.
Hold the TX card so that the slanted side faces
•
upward and insert the card into the port.
The TX card enables communication between the
•
main unit and the wireless receiver.
Connect the left and right rear
3
TX CARD
speakers to the wireless receiving
module.
Plug the power cord of the wireless
4
receiving module in the wall outlet and
switch the power switch ‘ON’.
Caution
Do not insert a card other than the TX card dedicated for the product. The product might be damaged or it may not be removed easily.
•
Do not insert the TX card upside down or in reverse direction.
•
Insert the TX card when the main unit is turned off.Inserting the card when it is turned on may cause a problem.
•
Turn on the main unit.
3
The Link LED of the wireless receiver module is lit
•
and the setup is finished.
If Power Standby mode continues, repeat Steps 1 to
•
3 above.
Caution
When the wireless receiving module setting is complete, no audio signal is output from the Rear Speaker OUT ports on the back
•
of the main unit.
The wireless receiving antenna is built into the wireless receiver module. Keep the unit away from water and moisture.
•
For optimal listening performance, make sure that the area around the wireless receiver module location is clear of any
•
obstructions.
Sound will be heard from the wireless rear speakers in DVD 5.1-CH or Dolby Pro Logic II mode only.
•
In 2-CH mode, no sound will be heard from the wireless rear speakers.
•
Note
Place the wireless receiver module at the rear of the listening position. If the wireless receiver module is too close to the main
•
unit, some sound interruption may be heard due to interference.
If you use a device such as a microwave oven, wireless LAN Card, Bluetooth equipment, or any other device that uses the same
•
frequency (2.4GHz) near the system, some sound interruption may be heard due to interference.
The transmission distance of radio wave is about 33 feet, but may vary depending on your operating environment.
•
If a steel-concrete wall or metallic wall is between the main unit and the wireless receiver module, the system may not operate at
all, because the radio wave cannot penetrate metal.
1615
Connecting the Video Out to TV
P.SCAN(Progressive Scan) Function
GB
Choose one of the two methods for connecting to a TV.
METHOD 1 METHOD 2
Unlike regular Interlace Scan, in which two fields of picture information alternate to create the entire
picture (odd scan lines, then even scan lines), Progressive Scan uses one field of information (all lines
displayed in one pass) to create a clear and detailed picture without visible scan lines.
Press STOP button.
1
If playing a disc, press the STOP button twice so that “STOP”, appears on the display.
•
Press and hold P.SCAN button on the remote control for over 5 seconds.
2
Pressing and holding the button for over 5 seconds will select "Progressive Scan" and "Interlace Scan"
•
alternately.
When you select P.SCAN, "P.SCAN" will appear on the display.
•
To set P.Scan mode for DivX discs, press the P.SCAN button on the remote control for more than
•
5 seconds with no disc in the unit (“'NO DISC" on the display), then load the DivX disc and play.
What is Progressive (or Non-Interlaced) Scanning?
Interlaced Scan (1 FRAME = 2 FIELDS)
Progressive Scan (FULL FRAME)
CONNECTIONS
METHOD 1 Composite Video
Connect the supplied video cable from the VIDEO OUT jack on the back panel of the
system to the VIDEO IN jack on your television.
METHOD 2 Component (Progressive Scan) Video
If your television is equipped with Component Video inputs, connect a component video
cable (not supplied) from the Pr, Pb and Y jacks on the back panel of the system to the
corresponding jacks on your television.
When the Progressive scan mode is selected, the VIDEO output (Yellow) does
Note
•
not output any signal.
...............
Good Quality
...............
Best Quality
In interlaced-scan video, a frame consists of two interlaced fields (odd and even), where each field contains
every other horizontal line in the frame.
The odd field of alternating lines is displayed first, and
then the even field is displayed to fill in the alternating
gaps left by the odd field to form a single frame.
One frame, displayed every 1/30th of a second, contains
two interfaced fields, thus a total of 60 fields are displayed every 1/60th of a second.
The interlaced scanning method is intended for capturing
a still object.
Note
This function works only on TVs equipped with component video inputs (Y, Pr, Pb) that support
•
Progressive Video. (It does not work on TVs with conventional component inputs, i.e., non-progressive
scan TVs.)
Depending on the capabilities of your TV, this function may not work.
•
The progressive scanning method scans one full frame of
video consecutively down the screen, line by line.
An entire image is drawn at one time, as opposed to the
interlaced scanning process by which a video image is
drawn in a series of passes.
The progressive scanning method is desirable for dealing
with moving objects.
17
18
Connecting External Components
Connecting an External Digital / Analog Component
Example: Digital signal components such as a Set-Top Box or CD Recorder.
Analog signal components such as a VCR.
Connecting the FM Antenna
FM Antenna (supplied)
GB
CONNECTIONS
Audio Cable
(not supplied)
If the external analog
component has only one
Audio Out, connect either left
or right.
Connect the Digital Input (OPTICAL) to the Digital Output on the external digital component.
1
Connect AUX (Audio) In on the Home Theater to Audio Out on the external analog component.
2
Be sure to match connector colors.
•
Press AUX on the remote control to select ‘DIGITAL IN / AUX1/AUX2’ input.
3
Each time the button is pressed, the selection changes as follows: AUX1 ➝ AUX2 ➝ DIGITAL IN
•
You can also use the FUNCTION button on the main unit.
•
The mode switches as follows: DVD/CD ➝ DIGITAL IN ➝ AUX1➝ AUX2 ➝ USB ➝ FM ➝ XM
Optical Cable
(not included)
Connect the FM antenna supplied to the FM 75Ω COAXIAL terminal.
1
Slowly move the antenna wire around until you find a location where reception is good, then
2
fasten it to a wall or other rigid surface.
This unit does not receive AM broadcasts.
Notes
•
Connecting an optional XM Satellite Radio Antenna
Cooling Fan
19
Note
The cooling fan supplies cool air to the unit to prevent overheating.
Please observe the following cautions for your safety.
•
Make sure the unit is well-ventilated. If the unit has poor ventilation, the temperature inside the unit could rise
and may damage it.
•
Do not obstruct the cooling fan or ventilation holes. (If the cooling fan or ventilation holes are covered with a
newspaper or cloth, heat may build up inside the unit and fire may result.)
You can connect the Video Output jack on your VCR to the TV, and connect the Audio
•
Output jacks on the VCR to this product.
Connect the XM Antenna(Sold separately) to the XM Antenna Connector on the rear of this unit.
Notes
To ensure optimal reception of XM’s satellite signal, the XM Antenna should be placed at or near a
•
southerly facing window with nothing obstructing its path to the sky. You can mount it indoors or outdoors.
When making connections, also refer to the operation instructions of the XM Antenna.
•
Depending on your location, the radio signal may be weak or cannot be tuned .
•
20
Before Using Your Home Theater
GROUP 1 GROUP 2
TRACK 1 TRACK 2 TRACK 1 TRACK 2TRACK 3
TITLE 1 TITLE 2
CHAPTER 1 CHAPTER 2 CHAPTER 1 CHAPTER 2CHAPTER 3
TRACK 1 TRACK 2 TRACK 4 TRACK 5TRACK 3
FILE 1 FILE 2
Your Home Theater is capable of playing DVD, CD, MP3/WMA and JPEG discs.Depending on the disc you are using,
these instructions may vary slightly. Read the instructions carefully before using.
To Operate your Samsung TV and the Home Theater with the HT-Q45's Remote Control
Disc terminology
Groups and tracks (DVD-AUDIO)
DVD-audio is divided into several large sections called "groups" and
•
smaller sections called "tracks". Numbers are allotted to these sections.
These numbers are called "group numbers" and "track numbers".
ENG
Plug the main unit's
power cord into the
1
AC power supply.
Press TV/VIDEO
button to select
4
VIDEO mode on
your TV.
VIDEO
Press TV button to
set the remote to TV
23
mode.
Press DVD RECEIVER
button to switch to
56
DVD RECEIVER
mode.
Press the POWER
button to turn on your
Samsung TV with this
remote.
Press FUNCTION button
on the main unit or DVD
button on the remote to
enable DVD/CD playback.
Titles and chapters (DVD-VIDEO)
DVD-video is divided into several large sections called "titles" and smaller
•
sections called "chapters". Numbers are allotted to these sections.
These numbers are called "title numbers" and "chapter numbers".
Tracks (Video and music CDs)
Video and music CDs are divided into sections called "tracks".
•
Numbers are allotted to these sections. These numbers are called
"track numbers".
OPERATION
Buttons Enabled for TV Operation: POWER, CHANNEL, VOLUME, TV/VIDEO, and Numeric (0-9) buttons.
Note
•
By default, the remote control is set to work with Samsung TVs.
•
See page 73 for more information about remote control operation with other manufacturer's TVs.
21
Note
Files (DivX)
DivX is divided into sections called "files".
•
Numbers are allotted to these sections. These numbers are called
"file numbers".
In this manual, the instructions marked with "DVD ( )" are applicable
•
to DVD-VIDEO, DVD-AUDIO, and DVD-R/RW discs.
Where a particular DVD type is mentioned, it is indicated separately.
Depending on the content of the disc, the initial screen may appear different.
•
DVD
22
Disc Playback
Selecting a Disc in the Disc changer
The DVD/CD function is automatically selected when Disc Skip is pushed.
ENG
Press OPEN/CLOSE button to open the
1
disc tray.
Load a disc.
Place a disc gently into the tray with the disc’s label
•
2
3
4
facing up.
Press DISC SKIP button.
Rotate the carousel tray so you can load the third, fourth,
•
and fifth discs.
Close the compartment by pressing the
OPEN/CLOSE button again.
To select a specific disc, press the corresponding DIRECT PLAY
(1, 2, 3, 4, 5) buttons on the front panel or DISC SKIP on the
remote control, until the required disc indicator flashes.
If the disc selected is not loaded, the next disc is played automatically.
•
To stop playback, press STOP during playback.
• If pressed once, “PRESS PLAY” is displayed and the stop position will be stored in memory.
If PLAY/PAUSE ( ) button or ENTER button is pressed, playback resumes from the stop position.
(This function works only with DVDs.)
• If pressed twice, “STOP” is displayed, and if PLAY/PAUSE ( ) button is pressed, playback starts from the
beginning.
OPERATION
Note
23
DVD CD
Playback starts automatically.
•
Depending on the content of the disc, the initial screen may appear different.
•
To temporarily pause playback, press PLAY/PAUSE during playback.
To resume playback, press PLAY/PAUSE ( ) button again.
•
24
Loading...