SAMSUNG HT-E8200 User Manual [it]

HT-E8200

2.1CH Blu-ray™

Home Entertainment System

user manual

imagine the possibilities

Thank you for purchasing this Samsung product. To receive more complete service, please register your product at

www.samsung.com/register

HT-E8200_XU_0315.indd 1HT-E8200_XU_0315.indd 1 2012-03-15 오후 1:09:312012-03-15 오후 1:09:31

Safety Information

Warning

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This symbol indicates “dangerous voltage” inside the product that presents a risk of electric shock or personal injury.

WARNING

• To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

CAUTION

• Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

• The Mains plug is used as a disconnect device and shall stay readily operable at any time.

• This apparatus shall always be connected to an AC outlet with a protective grounding connection.

• To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT PRODUCTO LÁSER CLASE 1

CLASS 1 LASER PRODUCT

This Compact Disc player is classified as a CLASS 1 LASER product. Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

CAUTION

• INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED, AVOID EXPOSURE TO BEAM.

This symbol indicates important instructions accompanying the product.

Wiring the Main Power Supply Plug (UK Only)

IMPORTANT NOTICE

The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug and if it requires replacing, a fuse approved to BS1362 of the same rating must be used. Never use the plug with the fuse cover removed. If the cover is detachable and a replacement is required, it must be of the same colour as the fuse fitted in the plug. Replacement covers are available from your dealer. If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should obtain a suitable safety approved extension lead or consult your dealer for assistance. However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect the plug to a mains socket as there is a risk of shock hazard from the bared flexible cord. Never attempt to insert bare wires directly into a mains socket. A plug and fuse must be used at all times.

IMPORTANT

The wires in the mains lead are coloured in accordance with the following code:– BLUE = NEUTRAL BROWN = LIVE As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows:–The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.

WARNING :

DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH LETTER E OR

BY THE EARTH SYMBOL , OR COLOURED GREEN OR GREEN AND YELLOW.

2 English

HT-E8200_XU_0315.indd 2HT-E8200_XU_0315.indd 2 2012-03-15 오후 1:10:002012-03-15 오후 1:10:00

Disc Storage & Management

• Holding Discs

- Fingerprints or scratches on a disc may reduce sound and picture quality or cause skipping.

- Avoid touching the surface of a disc where data has been recorded.

- Hold the disc by the edges so that fingerprints will not get on the surface.

- Do not stick paper or tape on the disc.

• Cleaning Discs

- If you get fingerprints or dirt on a disc, clean it with a mild detergent diluted in water and wipe with a soft cloth.

- When cleaning, wipe gently from the inside to the outside of the disc.

- Disc Storage

Do not keep in direct sunlight. Keep in a cool ventilated area. Keep in a clean protection jacket and store

vertically.

Handling Cautions

• Do not expose this apparatus to dripping or splashing. Do not put objects filled with liquids, such as vases, on the apparatus.

• To turn this apparatus off completely, you must pull the power plug out of the wall socket. Consequently, the power plug must be easily and readily accessible at all times.

• Do not touch the power plug with a wet hand. It can cause an electric shock.

• Do not plug multiple electric devices into the same wall socket. Ovedrloading a socket can cause it to overheat, resulting in a fire.

• Maintenance of the Cabinet

- Before connecting other components to this product, be sure to turn them off.

- If you move your product suddenly from a cold place to a warm place, condensation may occur on the operating parts and lens and cause abnormal disc playback. If this occurs, unplug the product, wait for two hours, and then connect the plug to the power outlet. Then, insert the disc, and try to play back again.

• If the product makes an abnormal noise or produces a burning smell or smoke, turn off the power switch immediately and disconnect the power plug from the wall outlet. Then, contact the nearest customer service centre for technical assistance. Do not use the product. Using the product as it is may cause a fire or an electric shock.

• To turn this apparatus off completely, you must pull the power plug out of the wall socket. Consequently, the power plug must be easily and readily accessible at all times.

Using the 3D Function

IMPORTANT HEALTH AND SAFETY INFORMATION FOR 3D PICTURES. Read and understand the following safety information before using the 3D function.

•

Some viewers may experience discomfort while viewing 3D TV such as dizziness, nausea, and headaches. If you experience any such symptom, stop viewing 3D TV, remove the 3D Active Glasses, and rest.

•

Watching 3D images for an extended period of time may cause eye strain. If you feel eye strain, stop viewing 3D TV, remove your 3D Active Glasses, and rest.

•

A responsible adult should frequently check on children who are using the 3D function. If there are any reports of tired eyes, headaches, dizziness, or nausea, have the child stop viewing 3D TV and rest.

•

Do not use the 3D Active Glasses for other purposes (such as general eyeglasses, sunglasses, protective goggles, etc.)

•

Do not use the 3D function or 3D Active Glasses while walking or moving around. Using the 3D function or 3D Active Glasses while moving around may cause you to bump into objects, trip, and/or fall, and cause serious injury.

01 Safety Information

English 3

HT-E8200_XU_0315.indd 3HT-E8200_XU_0315.indd 3 2012-03-15 오후 1:10:022012-03-15 오후 1:10:02

Safety Information

•

If you want to enjoy 3D content, connect a 3D device (3D compliant AV receiver or TV) to the product’s HDMI OUT port using a high-speed HDMI cable. Put on 3D glasses before playing the 3D content.

•

The product outputs 3D signals only through HDMI cable connected to the HDMI OUT port.

•

As the video resolution in 3D play mode is fixed according to the resolution of the original 3D video, you can not change the resolution to your preference.

•

Some functions such as BD Wise, screen size adjustment, and resolution adjustment may not operate properly in 3D play mode.

•

You must use a high-speed HDMI cable for proper output of the 3D signal.

•

Stay at least three times the width of the screen from the TV when watching 3D images. For example, if you have a 46 inch screen, stay 138 inches (3.5meters) from the screen.

- Place the 3D video screen at eye level for the best 3D picture.

•

When the product is connected to some 3D devices, the 3D effect may not function properly.

•

This product does not convert 2D content into 3D.

•

“Blu-ray 3D” and “Blu-ray 3D” logo are trademarks of the Blu-ray Disc Association.

manual may be reproduced or copied without the prior written permission of Samsung Electronics Co.,Ltd.

• Manufactured under licence under U.S. Patent Nos: 5,956,674; 5,974,380; 6,226,616; 6,487,535; 7,392,195; 7,272,567; 7,333,929; 7,212,872 & other U.S. and worldwide patents issued & pending. DTS-HD, the Symbol, & DTSHD and the Symbol together are registered trademarks & DTS-HD Master Audio | Essential is a trademark of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.

• ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit divx.com for more information and software tools to convert your files into DivX videos. ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod.divx.com for more information on how to complete your registration. DivX Certified® to play DivX® video up to HD 1080p, including premium content. DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under licence. Covered by one or more of the following U.S. patents : 7,295,673; 7,460,668; 7,515,710; 7,519,274

Licence

• The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other

countries.

• Dolby and the double-D symbol are registered trademarks of Dolby Laboratories.

4 English

HT-E8200_XU_0315.indd 4HT-E8200_XU_0315.indd 4 2012-03-15 오후 1:10:032012-03-15 오후 1:10:03

• Oracle and Java are registered trademarks of Oracle and/or its affiliates. Other names may be trademarks of their respective owners.

• This item incorporates copy protection technology that is protected by U.S. patents and other intellectual property rights of Rovi Corporation. Reverse engineering and disassembly are prohibited.

• Blu-ray Disc™, Blu-ray™, and the logos are trademarks of Blu-ray Disc Association.

• This product uses Cinavia technology to limit the use of unauthorized copies of some commercially-produced film and videos and their soundtracks. When a prohibited use of an unauthorized copy is detected, a message will be displayed and playback or copying will be interrupted.

More information about Cinavia technology

is provided at the Cinavia Online Consumer Information Centre at http://www.cinavia.com. To request additional information about Cinavia by mail, send a postcard with your mailing address to: Cinavia Consumer Information Centre, P.O. Box 86851, San Diego, CA, 92138, USA.”

This product incorporates proprietary technology

under licence from Verance Corporation and is protected by U.S. Patent 7,369,677 and other U.S. and worldwide patents issued and pending as well as copyright and trade secret protection for certain aspects of such technology. Cinavia is a trademark of Verance Corporation. Copyright 2004-2010 Verance Corporation. All rights reserved by Verance. Reverse engineering or disassembly is prohibited.

• Open Source Licence Notice

- In the case of using open source software, Open Source Licences are available on the product menu.

01 Safety Information

English 5

HT-E8200_XU_0315.indd 5HT-E8200_XU_0315.indd 5 2012-03-15 오후 1:10:052012-03-15 오후 1:10:05

Contents

SAFETY INFORMATION

2 Warning 3 Disc Storage & Management 3 Handling Cautions 3 Using the 3D Function 4 Copyright 4 Licence

GETTING STARTED

7 Disk and Format Compatibility 8 Logos of Discs the product can play 11 Accessories 12 Front & Side Panel 12 Rear Panel 13 Remote Control

CONNECTIONS

15 Connecting the Wireless Subwoofer 16 Attaching the Toroidal Ferrite Core to the

Power Cord

16 Connecting the FM Antenna 16 Installing the Cradle Stand 17 Installing the Wall Mount 18 Connecting to a TV 18

19 Connecting to External Devices 19

20 Connecting to a Network Router 20 20

Method 1

Video Cable - Good Quality

Method 2

HDMI Cable - Best Quality (Recommended)

Method 1

External Analogue Component

Method 2

an External Digital Audio Component

Method 3

External Component with an HDMI Cable

Wired Network Wireless Network

Connecting to a TV with a

Connecting to a TV with an

AUX IN : Connecting an

OPTICAL IN : Connecting

HDMI IN : Connecting to an

SETTINGS

21 The Initial Settings Procedure 23 The Home Screen 23 Accessing the Settings Screen 24 Settings Menu Functions 29 Networks and the Internet 33 Upgrading Software

MEDIA PLAY

35 The AllShare Play Screen 36 Playing Files on a USB Storage Device 37 The Function Screen 37 Playing Commercial Video Discs 37 Playing Commercial Audio Discs 38 Playing a Disc with User Recorded

Content

38 Using the AllShare Network Function 40 Controlling Video Playback 42 Controlling Music Playback 45 Playing Photo Contents 45 Using the Tools Menu when a File is

Highlighted

47 Listening to Radio 48 Using the Special Effects Remote Control

Buttons

NETWORK SERVICES

49 Using Smart Hub 51 BD-LIVE™

APPENDIX

52 Additional Information 57 Troubleshooting 60 Specifications

6 English

HT-E8200_XU_0315.indd 6HT-E8200_XU_0315.indd 6 2012-03-15 오후 1:10:052012-03-15 오후 1:10:05

Getting Started

Disk and Format Compatibility

Disc types and contents your product can play

Media Disc Type Size Details

Blu-ray Disc

3D Blu-ray Disc

VIDEO

MUSIC

PHOTO

NOTE

8cm Disc is not available. The product would be damaged if use. The product may not play certain CD-RW/-R and DVD-R because of the disc type or recording conditions. If a DVD-RW/-R disc has not been recorded properly in DVD video format, it will not be playable. Your product will not play content that has been recorded on a DVD-R at a bit-rate that exceeds 10 Mbps. Your product will not play content that has been recorded on a BD-R or USB device at a bit rate that exceeds 30 Mbps. Playback may not work for some types of discs, or when you use specific operations, such as angle change and aspect ratio

adjustment. Information about the discs is written in detail on the disc box. Please refer to this if necessary.

When you play a BD-J title, loading may take longer than a normal title or some functions may perform slowly.

DVD-VIDEO, DVD-RW,

DVD-R, DVD+RW,

DVD+R

CD-RW/-R,

DVD-RW/-R,

BD-RE/-R

CD-RW/-R,

DVD-RW/-R,

BD-RE/-R

BD-ROM or BD-RE/-R disc recorded in the BD-RE format.

DVD-VIDEO, recorded DVD+RW/DVD-RW(V)/DVD-R/+R discs that have been recorded and finalised, or a USB storage media containing DivX, MKV, MP4 contents.

12cm

Music recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R discs or a USB storage media containing MP3 or WMA contents.

Photos recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R discs or a USB storage media containing JPEG contents.

02 Getting Started

Disc types your product cannot play

• HD DVD

• DVD-ROM/PD/MVDisc, etc

NOTE

This product may not respond to all operating commands because some Blu-ray Disc, DVD, and CD discs allow specific or

limited operation and provide only certain features during playback. Please note that this is not a defect in the product.

Samsung cannot guarantee that this product will play every disc bearing the Blu-ray Disc, DVD or CD logo because disc

formats evolve, and problems and errors may occur during the creation of Blu-ray Disc, DVD, and CD software and/or the manufacture of discs.

Please contact the SAMSUNG Customer Care Centre, if you have questions or encounter difficulty when playing Blu-ray Disc,

DVD, or CD discs in this product. Also, refer to rest of this user manual for additional information on playback restrictions.

Some commercial discs and DVD discs purchased outside your region may not play on this product.

HT-E8200_XU_0315.indd 7HT-E8200_XU_0315.indd 7 2012-03-15 오후 1:10:062012-03-15 오후 1:10:06

• DVD-RAM

• Super Audio CD (except CD layer)

• DVD-RW(VR mode)

• CVD/CD-ROM/CDV/ CD-G/CD-I/LD (CD-Gs play audio only, not graphics.)

• 3.9 GB DVD-R Disc for Authoring.

English 7

Getting Started

Region Code

Both products and discs are coded by region. These regional codes must match for a disc to play. If the codes do not match, the disc will not play. The Region Number for this product is displayed on the rear panel of the product.

Disc Type

Blu-ray Disc

DVD-VIDEO

NOTE



If the Region number of a Blu-ray Disc/DVDs does not correspond to the Region number of this product, the product cannot play the disc.

Region

Code

North America, Central America, South America, Korea, Japan,

Taiwan, Hong Kong and South East Asia.

Europe, Greenland, French territories, Middle East, Africa,

Australia and New Zealand.

India, China, Russia, Central and

South Asia.

The U.S., U.S. territories and

Canada

Europe, Japan, the Middle East,

Egypt, South Africa, Greenland

Taiwan, Korea, the Philippines,

Indonesia, Hong Kong

Mexico, South America, Central America, Australia,

New Zealand, Pacific Islands, Caribbean

Russia, Eastern Europe, India, most of Africa, North Korea,

Mongolia

China

Area

Logos of Discs the product can play

Blu-ray Disc 3D Blu-ray Disc

BD-LIVE Dolby

DTS DivX

PAL broadcast system in

U.K, France, Germany, etc.

Java

Supported Formats

Music File Support

File

Extension

*.mp3

*.wma

Container

MP3

WMA

Audio

Codec

MP3 -

WMA

Support Range

Compliant with WMA version 10

* Sampling rates (in

kHz) - 8, 11, 16, 22, 32, 44.1, 48

* Bit rates - All bit-

rates in the range 5kbps to 384kbps

8 English

HT-E8200_XU_0315.indd 8HT-E8200_XU_0315.indd 8 2012-03-15 오후 1:10:072012-03-15 오후 1:10:07

Video File Support

File Extension Container Video Codec Resolution

*.avi

DivX 3.11/4.x

AVI

/5.1/6.0

H.264 BP/MP/HP 1920x1080 6 ~ 30 25

1920x1080 6 ~ 30 8

MPEG4 SP/ASP 1920x1080

*.mkv

MKV

DivX 3.11/4.x

/5.1/6.0

H.264 BP/MP/HP 1920x1080

1920x1080

MPEG4 SP/ASP 1920x1080

*.asf

ASF

DivX 3.11/4.x

/5.1/6.0

H.264 BP/MP/HP 1920x1080

1920x1080

MPEG4 SP/ASP 1920x1080

*.wmv

*.mp4

*.3gp

*.vro

WMV (wmv9)

MP4

3GPP

VRO VOB

Window Media

Video v9

1920x1080

H.264 BP/MP/HP 1920x1080

MPEG4 SP/ASP 1920x1080

H.264 BP/MP/HP 1920x1080

MPEG4 SP/ASP 1920x1080

MPEG2 1920x1080

MPEG1 1920x1080

*.mpg

*.mpeg

MPEG2 1920x1080

H.264 1920x1080

*.ts *.tp

*.trp

MPEG2 1920x1080

H.264 1920x1080

VC1 1920x1080

Frame rate

(fps)

6 ~ 30 8

6 ~ 30 25 6 ~ 30 8

6 ~ 30 8

6 ~ 30 25 6 ~ 30 8

6 ~ 30 25 WMA

6 ~ 30 25 6 ~ 30 8

6 ~ 30 25

6 ~ 30 8

24/25/30 25

24/25/30 25 24/25/30 25

24/25/30 25

6 ~ 30 25

24/25/30 25

6 ~ 30 25

Limitations

- Even when a file is encoded by a supported codec listed above, the file might not be played if its content has a problem.

- Normal playback is not guaranteed if the file’s container information is wrong or the file itself is corrupted.

- Files having higher bit or frame rates than standard may stutter when played back.

- The Seek (skip) function is not available if the file’s index table is damaged.

- When you playback a file remotely through a network connection, video playback may stutter depending on the network speed.

Bit rate (Mbps)

Audio Codec

MP3 AC3

LPCM

DTS Core

MP3 AC3

LPCM

DTS Core

MP3 AC3

LPCM

WMA

MP3 AAC

AAC

AC3 MPEG LPCMMPEG1 1920x1080

AC3 MPEG LPCM

AAC

AC3

AAC

MP3

DD+

02 Getting Started

English 9

HT-E8200_XU_0315.indd 9HT-E8200_XU_0315.indd 9 2012-03-15 오후 1:10:102012-03-15 오후 1:10:10

Getting Started

Video decoder

- Supports up to H.264 Level 4.1

- Does not support H.264 FMO/ASO/RS, VC1 SP/MP/AP L4 and AVCHD

- MPEG4 SP, ASP : Below 1280 x 720 : 60 frames max Above 1280 x 720 : 30 frames max

- Does not support GMC 2 or higher

Audio decoder

- Supports WMA 7, 8, 9 and STD

- Does not support WMA 9 PRO multi-channel files if the number of channels is more than 2 or the files require lossless audio decoding.

- Does not support WMA sampling rate of 22050Hz mono



Supported DivX subtitle file formats

*.ttxt, *.smi, *.srt, *.sub, *.txt

Notes on the USB connection

• Your product supports USB storage media, MP3 players, digital cameras, and USB card readers.

• The product does not support folder or file names longer than 128 characters.

• Some USB/digital camera devices may not be compatible with the product.

• Your product supports the FAT 16, FAT 32, and NTFS files systems.

• Connect USB devices directly to the product’s USB port. Connecting through a USB cable may cause compatibility problems.

• Inserting more than one memory device into a multi-card reader may cause the reader to operate improperly.

• The product does not support the PTP protocol.

• Do not disconnect a USB device during a “loading” process.

• The bigger the image resolution, the longer the image takes to display.

• This product cannot play MP3 files with DRM (Digital Rights Management) downloaded from commercial sites.

• Your product only supports video that is under 30fps (frame rate).

• Your product only supports USB Mass Storage Class (MSC) devices such as thumb drives and USB HDD. (HUB is not supported.)

• Certain USB HDD Devices, multi-card readers and thumb drives may not be compatible with this product.

• If some USB devices require excessive power, they may be limited by the circuit safety device.

• If playback from a USB HDD is unstable, provide additional power by plugging the HDD into a wall socket. If the problem continues, contact the USB HDD manufacturer.

• You must remove the USB storage device safely (by performing the “Safely Remove USB” function) to prevent possible damage to the USB memory. Press the HOME button to move to the home menu, press the YELLOW (C) button, and then press the E button.

• SAMSUNG is not responsible for any data file damage or data loss.

AVCHD (Advanced Video Codec High Definition)

• This product can play back AVCHD format discs. These discs are normally recorded and used in camcorders.

• The AVCHD format is a high definition digital video camera format.

• The MPEG-4 AVC/H.264 format compresses images with greater efficiency than the conventional image compressing format.

• Some AVCHD discs use the “x.v.Colour” format. This product can play back AVCHD discs that use “x.v.Colour” format.

• “x.v.Colour” is a trademark of Sony Corporation.

• “AVCHD” and the AVCHD logo are trademarks of Matsushita Electronic Industrial Co., Ltd. and Sony Corporation.

NOTE

Some AVCHD format discs may not play, depending on

the recording conditions. AVCHD format discs need to be finalised. “x.v.Colour” offers a wider colour range than normal DVD

camcorder discs. Some DivX, MKV and MP4 format discs may not play,

depending on their video resolution and frame rate.

10 English

HT-E8200_XU_0315.indd 10HT-E8200_XU_0315.indd 10 2012-03-15 오후 1:10:102012-03-15 오후 1:10:10

Accessories

Check for the supplied accessories below.

02 Getting Started

Video Cable FM Antenna

User Manual Audio Gender

RECEIVER

BD TV

123 4

56 809

DISC MENU TITLE MENU

MUTE

S/W LEVEL

VOL

FULL SCREEN REPEATHOME

TOOLS

RETURN

TUNER

MEMORY

ABCD

'ĺ'

SMART SEARCH

HUB

vTuner

AUDIO

SUBTITLE

FUNCTION

SOURCE

POPUP

TUNING

/ CH

INFO

EXIT

3D SOUND

SLEEP

MO/ST

SOUND

EFFECT

USB Cable Bracket Wall Mount

Cradle Stand/Cradle Stand Screw Toroidal Ferrite Core (2EA) Remote Control/Batteries (AAA size)

NOTE

The dedicated USB cable is provided for communicating with the external USB device. It is recommended to use the provided USB cable as a vibration may occur depending on the connected USB device.



Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance.



An administration fee may be charged if either

a. an engineer is called out at your request and there is no defect in the product (i.e. where you have

failed to read this user manual)

you bring the unit to a repair centre and there is no defect in the product (i.e. where you have failed to read this user manual).



The amount of such administration charge will be advised to you before any work or home visit is carried out.

English 11

HT-E8200_XU_0315.indd 11HT-E8200_XU_0315.indd 11 2012-03-15 오후 1:10:112012-03-15 오후 1:10:11

Getting Started

AUX IN

5V 500mA

HDMI OUT

HDMI IN 1 HDMI IN 2

LAN

VIDEO OUT

OPTICAL IN

FM ANT

Front & Side Panel

REMOTE CONTROL SENSOR

DISC SLOT

DISPLAY

POWER

USB HOST

AUX IN

BUTTON POINTER

NOTE

To upgrade the product's software through the USB Host jack, you must use a USB memory stick. When the product displays the Blu-ray Disc menu, you cannot start the movie by pressing the 6 button on the product or

the remote. To play the movie, you must select Play Movie or Start in the disc menu, and then press the

button.

Rear Panel

LAN

HDMI OUT VIDEO OUT

HDMI IN 1

FM ANT

EJECT

FUNCTION

STOP

PLAY/PAUSE

ENTER

VOLUME

POWER

HDMI IN 2

OPTICAL IN

COOLING FANMOUNTING STUDS

NOTE

Ensure a minimum of 10 cm of clear space on all sides of the home cinema to ensure adequate ventilation. Do not obstruct

the cooling fan or ventilation holes.

12 English

HT-E8200_XU_0315.indd 12HT-E8200_XU_0315.indd 12 2012-03-15 오후 1:10:232012-03-15 오후 1:10:23

Remote Control

Tour of the Remote Control

Turn the product on and off.

To change to TV mode, press the

TV button.

To change to Home Cinema,

press the BD button.

Press numeric buttons to operate

options.

Press to view the disc menu.

Press to skip backwards or forwards.

Press to stop/play a disc.

Cut off the sound temporarily.

FUNCTION

SOURCE

RECEIVER

BD TV

1 4 7

DISC MENU TITLE MENU

SLEEP

3 56 809

POPUP

MUTE

02 Getting Started

Press to select Blu-ray's mode (HDMI1, AUX, BD/DVD, etc.). or Press to select TV's video mode.

Set a Sleep time to shut off the product.

To eject the disc.

Use to enter the Popup menu/ Title menu.

Press to search backwards or forwards.

Press to pause a disc.

Adjust the volume.

Press to move to the Home screen.

Press this to see the full screen

on a TV.

Press to use the Tools menu.

Select on-screen menu items and

change menu value.

Return to the previous menu.

These buttons are used both for

menus on the product and also

several Blu-ray Disc functions.

Press to use Smart Hub.

Press this to use the vTuner.

Press to search contents.

Selects the disc Audio language.

VOL

FULL SCR EEN REPEATHOME

TOOLS

RETURN

ABCD

SMART SEARCH

HUB

vTuner

AUDIO

TUNER

MEMORY

'ĺ'

SUBTITLE

/ CH

INFO

EXIT

MO/ST

3D SOUND

SOUND

EFFECT

TUNING

S/W LEVEL

Search for active FM stations and to change channels.

Use to adjust the level of the subwoofer.

Allows you to repeat a title, chapter, track or disc.

Use to display the playback information when playing a Blu-ray/DVD disc.

Press to exit the menu.

Use to set a preset radio frequency.

Select MONO or STEREO for radio broadcasts.

Press to apply 3D sound effect.

Press to apply sound effects. Press to enjoy an ordinary 2D video

in 3D mode. Selects the disc subtitle language.

English 13

HT-E8200_XU_0315.indd 13HT-E8200_XU_0315.indd 13 2012-03-15 오후 1:10:252012-03-15 오후 1:10:25

Getting Started

Installing batteries in the Remote Control

Battery size: AAA

NOTE

Make sure to match the “+” and “–” ends of the batteries

with the diagram inside the compartment.

Assuming typical TV usage, the batteries last for about

one year.

The remote control can be used up to approximately

7 meters from the product in a straight line.

Setting the Remote Control

You can control certain functions of your TV with this remote control.

When operating a TV with the remote control

1 . Press the TV button to set the remote control

to TV mode.

2 . Turn on your TV. 3 . While holding down the POWER button,

enter the code corresponding to your brand of TV.

• If there is more than one code listed for your TV in the table, enter one at a time to determine which code works.

• Example : For a Samsung TV While holding down the POWER button, use the number buttons to enter 00. If that does not work, try 15, then 16, etc.

4 . If the TV turns off, the setting is complete.

• You can use the TV POWER, VOLUME, CHANNEL, and Numeric buttons (0~9).

NOTE

The remote control may not work on some brands of TV's.

Also, some operations may not be possible, depending on your brand of TV.

The remote control will work with Samsung TVs by

default.

14 English

TV Control Codes

Brand Code

Admiral

(M.Wards)

A Mark 01, 15

Anam

AOC 01, 18, 40, 48

Bell & Howell

(M.Wards) Brocsonic 59, 60

Candle 18

Cetronic 03

Citizen 03, 18, 25 Cinema 97 Classic 03

Concerto 18

Contec 46

Coronado 15

Craig 03, 05, 61, 82, 83, 84

Croslex 62

Crown 03

Curtis Mates 59, 61, 63

CXC 03

Daewoo

Daytron 40 Dynasty 03

Emerson

Fisher 19, 65

Funai 03

Futuretech 03

General

Electric (GE)

Hall Mark 40

Hitachi 15, 18, 50, 59, 69

Inkel 45

JC Penny 56, 59, 67, 86

JVC 70 KTV 59, 61, 87, 88 KEC 03, 15, 40 KMC 15

LG (Goldstar)

Luxman 18

LXI (Sears)

Magnavox

Marantz 40, 54

Matsui 54

MGA 18, 40

56, 57, 58

01, 02, 03, 04, 05,

06, 07, 08, 09, 10, 11,

12, 13, 14

57, 58, 81

02, 03, 04, 15, 16, 17, 18, 19, 20, 21, 22, 23,

24, 25, 26, 27, 28,

29, 30, 32, 34, 35, 36,

48, 59, 90

03, 15, 40, 46, 59, 61,

64, 82, 83, 84, 85

06, 40, 56, 59, 66,

67, 68

01, 15, 16, 17, 37, 38, 39, 40, 41, 42, 43, 44

19, 54, 56, 59, 60, 62,

63, 65, 71

15, 17, 18, 48, 54, 59,

60, 62, 72, 89

Brand Code

Mitsubishi/MGA

Onking 03

Panasonic

Penney 18

Philips

Pioneer 63, 66, 80, 91 Portland 15, 18, 59

Proton 40

Quasar 06, 66, 67

Radio Shack 17, 48, 56, 60, 61, 75

RCA/Proscan

Realistic 03, 19

Sampo 40

Samsung

Sanyo 19, 61, 65

Sharp 15, 57, 64

Signature 2000

(M.Wards)

Soundesign 03, 40

Spectricon 01

Sylvania

Symphonic 61, 95, 96

Tatung 06

Techwood 18

Teknika 03, 15, 18, 25

Toshiba 19, 57, 63, 71 Vidtech 18

Videch 59, 60, 69

Wards

Yamaha 18

Yupiteru 03

Zenith 58, 79 Zonda 01

Dongyang 03, 54

18, 40, 59, 60, 75 MTC 18 NEC 18, 19, 20, 40, 59, 60

Nikei 03

Onwa 03

06, 07, 08, 09, 54, 66,

67, 73, 74

03, 15, 17, 18, 48, 54,

Philco

Scott 03, 40, 60, 61 Sears 15, 18, 19

Sony 50, 51, 52, 53, 55

SSS 18

TMK 18, 40

York 40

59, 62, 69, 90

15, 17, 18, 40, 48,

54, 62, 72

18, 59, 67, 76, 77, 78,

92, 93, 94

00, 15, 16, 17, 40, 43,

46, 47, 48, 49,

59, 60, 98

57, 58

18, 40, 48, 54, 59,

60, 62

15, 17, 18, 40, 48,

54, 60, 64

HT-E8200_XU_0315.indd 14HT-E8200_XU_0315.indd 14 2012-03-15 오후 1:10:292012-03-15 오후 1:10:29

Connections

This section involves various methods of connecting the product to other external components. Before moving or installing the product, be sure to turn off the power and disconnect the power cord.

Connecting the Wireless Subwoofer

The Subwoofer's linking ID is preset at the factory and the main unit and sub should link (connect wirelessly) automatically when turned on. If the link indicator does not light when main unit and subwoofer are turned on, please set the ID by following the process below.

1 . Plug the power cords of the main unit and subwoofer into the AC power supply. 2 . Press the ID SET button on the back of the subwoofer with a small, pointed object for 3 seconds.

• The STANDBY indicator is turned off and the LINK indicator (blue LED) blinks quickly.

ID SET

3 . In stand-by mode while the main unit is off, press the 0, 1, 3, 5 buttons in order.

• The red standby LED on main unit flashes and then stop in few second.

4 . Press the POWER button to turn on the main unit.

• The main unit and the subwoofer are now linked (connected).

• The Link indicator (blue LED) on the subwoofer is turned on.

NOTE



Before moving or installing the product, be sure to turn off the power and disconnect the power cord. If the main unit is powered off, the wireless subwoofer will be in the standby mode and the STANDBY LED on the upper side will blink. If the main unit doesn't make wireless connection, follow steps 1-4 above to retry the connection between the main unit and wireless

subwoofer.

CAUTION



The wireless receiving antenna is built into the wireless subwoofer. Keep the unit away from water and moisture. For optimal listening performance, make sure that the area around the wireless subwoofer location is clear of any obstructions.

03 Connections

English 15

HT-E8200_XU_0315.indd 15HT-E8200_XU_0315.indd 15 2012-03-15 오후 1:10:302012-03-15 오후 1:10:30

Connections

HDMI OUT

HDMI IN 1 HDMI IN 2

LAN

VIDEO OUT

OPTICAL IN

FM ANT

HDMI OUT

HDM

HDMI IN 2

LAN

VIDEO

OPTICAL IN

FM ANT

Attaching the Toroidal Ferrite Core to the Power Cord

If you attach a Toroidal ferrite core to the power cord, it will help to prevent RF interference from radio signals.

ID SET

1. Pull the fixing tab of the Toroidal ferrite core to open it.

2. Make a loop twice in the power cord.

Attach the Toroidal ferrite core to the power cord as the figure shows and press it until it clicks.

Connecting the FM Antenna

1 . Connect the FM antenna supplied to

the FM ANT Jack.

2 . Slowly move the antenna wire

FM Antenna (supplied)

around until you find a location where reception is good, then fasten it to a wall or other rigid surface.

NOTE

This product does not receive AM broadcasts.

Installing the Cradle Stand

1 . Put the 3 bumps on the product into

the three holes on the cradle stand.

2 . Put the supplied a screw in the

product and rotate them clockwise with screw driver.

Screw

3 bumps

16 English

HT-E8200_XU_0315.indd 16HT-E8200_XU_0315.indd 16 2012-03-15 오후 1:10:322012-03-15 오후 1:10:32

Installing the Wall Mount

You can use the wall mount bracket to mount this unit on a wall.

Installation Precautions

• Do not install on a place other than a vertical wall.

• For the installation, avoid a location with high temperature or humidity.

• Check the strength of the wall. If the strength of the wall is insufficient for the product installation, make sure to reinforce the wall before the installation.

• Check the material of the wall. If the wall is made of plaster board, marble, or iron board, purchase and use the appropriate fixing screws.

• Cables connecting to external devices need to be connected to the set before installing.

• Be sure to turn off and unplug the unit before installation. Otherwise, it may cause electric shock.

1 . Rotate a screw on the cradle stand counter-

clockwise to seperate them from the unit.

2 . Place the wall mount bracket on a wall surface and

then secure it with two screws (not supplied). Be sure to install the wall mount bracket so that the



arrow (

) is placed in the centre of the TV.

3 . Then, fit the unit into the corresponding slots of the

wall mount bracket. For secure installation, make sure the mounting studs slide firmly down into the bottom of the slots.

4 . This is the completion of the suggested wall mount

installation.

03 Connections

HDMI OUT

LAN

VIDEO OUT

HDMI IN 1 HDMI IN 2

FM ANT

OPTICAL IN

NOTE

Do not hang onto the installed unit and avoid any impact to the

unit.

When the unit is installed on a wall, please make sure that a child

does not pull any of connecting cables, as it may cause it to fall.

When you install the product with TV on the wall, leave sufficient

space for ejecting a CD. (Disc size 12cm+ space for moving hands)

English 17

HT-E8200_XU_0315.indd 17HT-E8200_XU_0315.indd 17 2012-03-15 오후 1:10:352012-03-15 오후 1:10:35

Connections

HDMI IN VIDEO IN

HDMI OUT

HDMI IN 1 HDMI IN 2

LAN

VIDEO OUT

OPTICAL IN

FM ANT

Connecting to a TV

Select either Method 1 or Method 2.

• If you have set the product's remote control to operate your TV, press the TV SOURCE button on the remote control,

and then select the correct external source from the TV's source list (HDMI, Video In, etc.) to view video from the home Cinema.

(Cable not supplied.)

Method 1

Method 2

Method 1 Connecting to a TV with a Video Cable - Good Quality

Connect the supplied Video cable from the VIDEO OUT jack on the back of the product to the VIDEO IN jack on your TV.

Method 2 Connecting to a TV with an HDMI Cable - Best Quality (Recommended)

Connect an HDMI cable (not supplied) from the HDMI OUT jack on the back of the product to the HDMI IN jack on your TV. If the TV supports ARC, you can hear TV sound from home cinema with only connect this cable.

NOTE

The VIDEO Out jack always outputs in the 576i/480i resolution regardless of the resolution set in the Setup menu. Do not connect the unit through a VCR. Video signals fed through VCRs may be affected by copyright protection systems and

the picture will be distorted on the television.

18 English

HT-E8200_XU_0315.indd 18HT-E8200_XU_0315.indd 18 2012-03-15 오후 1:10:382012-03-15 오후 1:10:38

Connecting to External Devices

HDMI OUT

HDMI IN 1 HDMI IN 2

LAN

VIDEO OUT

OPTICAL IN

FM ANT

HDMI OUT

AUDIO OUT

OPTICAL OUT

AUX IN

To select the correct mode for an external device, press the FUNCTION button. Each time you press the button, the mode changes in this order : BD/DVD  D. IN  AUX  HDMI1  HDMI2  FM BT

Audio Cable (not supplied) If the external analogue component has only one Audio Out, connect either left or right.

(Cable not supplied.)

Method 1

External Devices

Method 1 AUX IN : Connecting an External Analogue Component

Using an RCA audio cable (not supplied), connect the AUDIO In jack on the product to the AUDIO Out jack on the external analogue component.  Select the AUX mode.

• Be sure to match the colours on the cable plugs to the colours on the input and output jacks.

(Cable not supplied.)

Method 2

(Cable not supplied.)

Method 3

03 Connections

Method 2 OPTICAL IN : Connecting an External Digital Audio Component

To connect the digital audio output of digital signal components such as Cable Boxes and Satellite Receivers (Set-Top-Boxes).

Using a digital optical cable (not supplied), connect the Optical Digital Audio In jack on the product to the Digital Optical Out jack of the external digital device using a digital optical cable.

Select the D. IN mode.



Method 3 HDMI IN : Connecting to an External Component with an HDMI Cable

Connect an HDMI cable (not supplied) from the HDMI IN jack on the back of the product to the HDMI OUT jack on your digital device.  Select the HDMI1 or HDMI2 mode.

NOTE

To see video from your Cable Box/Satellite receiver, you must connect its video output directly to your TV. This system supports Digital sampling frequencies of 32 kHz or higher from external digital components. This system supports only DTS and Dolby Digital audio. MPEG audio, a bitstream format, is not supported.

English 19

HT-E8200_XU_0315.indd 19HT-E8200_XU_0315.indd 19 2012-03-15 오후 1:10:402012-03-15 오후 1:10:40

Connections

HDMI OUT

HDMI IN 1 HDMI IN 2

LAN

VIDEO OUT

OPTICAL IN

FM ANT

Connecting to a Network Router

You can connect your product to your network router using one of the methods illustrated below.

Wired Network

Broadband modem

(with integrated router)

Router

Broadband

modem

NOTE

 Internet access to Samsung’s Software Update server

may not be allowed, depending on the router you use or your ISP’s policy. For more information, contact your ISP (Internet Service Provider).

 DSL users, please use a router to make a network

connection.

 To use the AllShare Play function, you must connect your

PC to your network as shown in the illustrations on the left. The connection can be wired or wireless.

Broadband service

Wireless Network

Wireless IP sharer

Broadband

service

NOTE

 If your wireless IP router supports DHCP, this product can

use a DHCP or static IP address to connect to the wireless network.

 Set your wireless IP router to Infrastructure mode. Ad-hoc

mode is not supported.

 The product supports only the following wireless security

key protocols:

- WEP (OPEN/SHARED), WPA-PSK (TKIP/AES), WPA2-PSK

(TKIP/AES)

 Select a channel on the wireless IP router that is not

currently being used. If the channel set for the wireless IP router is currently being used by another device nearby, it will result in interference and communication failure.

 If you select the Pure High-throughput (Greenfield)

802.11n mode and set the Encryption type on your router or AP to WEP, TKIP or TKIP-AES (WPS2Mixed), the product will not support a connection in compliance with new WiFi certification specifications.

 Wireless LAN, by its nature, may cause interference,

depending on the operating conditions (AP performance, distance, obstacles, interference by other radio devices, etc).

20 English

HT-E8200_XU_0315.indd 20HT-E8200_XU_0315.indd 20 2012-03-15 오후 1:10:422012-03-15 오후 1:10:42

Settings

The Initial Settings Procedure

• The Home menu will not appear if you do not configure

the initial settings.

• The OSD (On Screen Display) may change in this

product after you upgrade the software version.

• The access steps may differ depending on the menu

you selected.

1 . Turn on your TV after connecting the product,

and then turn on the product. When you turn on the product for the first time, the product automatically displays the Initial Settings Language screen.

2 . Use the ▲▼◄► buttons on the remote

to select the desired language, and then press the E button twice. The Start screen appears.

3 . Press the E button to start setup. The

Network Settings screen appears.

Network Settings (1/5)

Initial Settings

The next step is to set up a wireless network using an internal LAN Adapter.

If you want to connect to your wired network, plug in a network cable.

4 . Press the E button to set up the product’s

wireless network connection or select Skip, and then press the E button to skip network setup. If you selected Skip, go to Step 12.

NOTE

The product starts the wireless network connection

procedure by default. If you want to set up a wired connection, select Skip, and then go to "Configuring Your Network Connection" on page 29 after you have completed the Initial Settings Procedure.

Skip

If you skip wireless network setup here, go to "Wireless

Network" on page 30 to set up the product's wireless network connection later.

5 . The product searches for and then displays

all available wireless router network connections.

Initial Settings > Network Settings (2/5)

Select your wireless router from the list.

KIMING_VTOWER

TIAS si-ap surlwang5

Add Network

1 / 4

Refresh

WPS(PBC)

Skip

6 . Use the ▲▼ buttons to select a router, and

then press the E button. The Next button is highlighted.

7 . Press the E button to continue. The

Security Key screen appears.

NOTE

If you have a WPS(PBC) compatible router, select

WPS(PBC) instead, press the E button, and then follow the directions on the screen. When done, go to Step 10.

Initial Settings > Network Settings (4/5)

Enter security key.

A/a  Space   

0 entered

WPS PIN

Skip

8 . Enter your network's security key. When

done, use the ▲▼◄► buttons to select

Next, and then press the E button.

04 Settings

English 21

HT-E8200_XU_0315.indd 21HT-E8200_XU_0315.indd 21 2012-03-15 오후 1:10:452012-03-15 오후 1:10:45

Settings

NOTE

Enter numbers by pressing the number buttons on your

remote.

Enter letters by selecting a letter using the ▲▼◄►

buttons, and then press E button.

To display capital letters (or redisplay small letters if

capital letters are displayed), select A/a, and then press the E button.

To display symbols and punctuation, select , and then

press the E button. To redisplay letters, select , and then press the E button.

9 . If the connection is successful, the

Connection Complete screen appears. Select Next, and then press the E button. The Software Update screen appears.

NOTE

If the connection is not successful, select Next, and then

press the E button. After you have completed the Initial Settings procedure, go to "Wireless Network" on page 30 to set up the product's wireless network connection.

10 . To upgrade the software, select Update

now, and then press the E button. To skip

the upgrade, select Update later, press the

button, and go to Step 12.

NOTE

If you skipped network set up, you must skip Software

Update also.

11 . If there is a Software Update available,

the product downloads and installs the upgrade. This can take some time. If there is no Software Update available, the "There

are no new software updates for you to download. You already have the most up to date version." message appears. And

then press the E button. The TV Aspect Ratio screen appears.

Initial Settings > TV Aspect Ratio

Set to match the type of television connected.

16:9 Original

16:9 Full

4:3 Letter Box

4:3 Pan-Scan

22 English

Select when connecting to a 16:9 TV Screen. All content will be displayed at original aspect ratio. Content formatted in 4:3 will be displayed with black bars on left and right.

12 . Using the ▲▼ buttons, select the aspect ratio

that matches your screen, and then press the

button. Select Next, and then press the

button.

You have four choices: 16:9 Original - For widescreen TVs. Displays

widescreen pictures in their original 16:9 format and 4:3 pictures (the old, standard format) in 4:3 pillar box format with black bars on the left and right.

16:9 Full - For widescreen TVs. Displays widescreen pictures in their original 16:9 format and expands 4:3 pictures to fill the 16:9 screen.

4:3 Letter Box - For older, standard screen analogue TVs. Displays 4:3 pictures in full screen and 16:9 pictures in letter box format that retains the 16:9 aspect ratio but puts black bars above and below the picture.

4:3 Pan-Scan - For older, standard screen analogue TVs. Displays 4:3 pictures in full screen and 16:9 pictures in Pan-Scan format that fills the screen, but cuts off the left and right sides of the picture and enlarges the middle vertically.

Initial Settings > Complete

Setup completed.

On-Screen Language

Network Settings

Software Update -

TV Aspect

Press Smart Hub to



enjoy a variety of



Internet content.



Smart Hub

13 . The Setup completed screen appears. Check

the settings to confirm they are correct. Select OK, and then press the E button. The Home screen appears.

NOTE

If you want to display the Initial Setting screen again and

make changes, select the Reset option. (See page 28)

If you use an HDMI cable to connect the product to an

Anynet+ (HDMI-CEC)-compliant Samsung TV and 1.) You have set the Anynet+ (HDMI-CEC) feature to ON in both the TV and the product and 2.) You have set the TV to a language supported by the product, the product will select that language as the preferred language automatically.

HT-E8200_XU_0315.indd 22HT-E8200_XU_0315.indd 22 2012-03-15 오후 1:10:492012-03-15 오후 1:10:49

TOOLS

RETURN

EXIT

INFO

TUNER

FU LL SC REEN REPEATHOME

The Home Screen

Play videos or music, or view photos from discs or connected devices.

Smart Hub Function Settings

Smart Hub. Starts Smart Hub. From Smart Hub,

you can access YouTube, games, and other apps.

AllShare Play. Play videos, photos or music content

from Disc, USB, PC or mobile devices.

Function. Select the audio/video input source.

Settings. Set various functions to suit your personal

preferences.

Selecting an Option on the Home Screen

1 . To select an option on the Home screen,

move the cursor using the ◄► buttons until it highlights the option of your choice, and then press the E button.

AllShare Play

Accessing the Settings Screen

1 . Select Settings on the Home screen, and

then press E. The Settings screen appears.

Display

Audio

Network

System

Support

3D Settings TV Aspect Ratio 16:9 Original Smart Hub Screen Size Size 3

BD Wise Off

Resolution Auto Movie Frame (24Fs) Auto HDMI Colour Format Auto HDMI Deep Colour Auto Progressive Mode Auto

2 . To access the menus, sub-menus, and

options on the Settings screen, please refer to the remote control illustration below.

NOTE

04 Settings

If you leave the product in the stop mode for more than

5 minutes without using it, a screen saver will appear on

your TV. If the product is left in the screen saver mode for more than 20 minutes, the power will automatically turn

off.

Buttons on the Remote Control Used for the Settings Menu

HOME Button : Press to move to the Home screen.

RETURN Button : Return to the previous menu.

(Enter) / DIRECTION Button :

~Press

an item.

~Press the E button to activate the currently

selected item or confirm a setting.

EXIT Button : Press to exit the current menu.

NOTE

The E button on the product's front panel can be

used for same purpose as the E button on the remote control.

Detailed Function Information

Each Settings function, menu item, and individual option is explained in detail on-screen. To view an explanation, use the ▲▼◄► buttons to select the function, menu item, or option. The explanation will usually appear on the right of the screen. A short description of each Settings function starts on the next page. Additional information on some of the functions is also in the Appendix of this manual.

to move the cursor or select

▲▼◄►

HT-E8200_XU_0315.indd 23HT-E8200_XU_0315.indd 23 2012-03-15 오후 1:10:512012-03-15 오후 1:10:51

English 23

Settings

Settings Menu Functions

Display

3D Settings

TV Aspect

Ratio

Smart Hub

Screen Size

BD Wise

Resolution

Movie Frame

(24Fs)

Set up the 3D related functions.

3D Blu-ray Playback Mode: Select whether to play a Blu-

ray Disc with 3D contents in 3D Mode. If you move to the Home or Smart Hub Home menu while in 3D mode, the product will switch to 2D automatically.

Screen Size: Enter the size of the TV attached to the

product. The product will automatically adjust the 3D output to the screen size of the TV.

Lets you adjust the output of the product to the screen size of your TV. See page 22, Step 12 for a description of the screen size options.

Lets you select the optimal size for the Smart Hub Screen.

BD Wise is Samsung’s latest inter-connectivity feature. When you connect a Samsung product and a Samsung TV with BD Wise to each other via HDMI, and BD Wise is on in both the product and TV, the product outputs video at the video resolution and frame rate of the Blu-ray/DVD Disc.

Lets you set the output resolution of the HDMI video signal to Auto, 1080p, 1080i, 720p, 576p/480p. If Composite is connected, the resolution supports only 576i/480i. The number indicates the number of lines of video per frame. The i and p indicate interlaced and progressive scan, respectively. The more lines, the higher quality.

Setting the Movie Frame (24Fs) feature to Auto lets the product adjust its HDMI output to 24 frames per second automatically for improved picture quality if attached to a 24Fs compatible TV.

• You can enjoy the Movie Frame (24Fs) feature only on a TV supporting this frame rate.

• Movie Frame is only available when the product is in the HDMI 1080i or 1080p output resolution modes.

HDMI Colour

Format

HDMI Deep

Colour

Progressive

Mode

24 English

HT-E8200_XU_0315.indd 24HT-E8200_XU_0315.indd 24 2012-03-15 오후 1:11:022012-03-15 오후 1:11:02

Lets you set the colour space format for the HDMI output to match the capabilities of the connected device (TV, monitor, etc).

Lets you set the product to output video from the HDMI OUT jack with Deep Colour. Deep Colour provides more accurate colour reproduction with greater colour depth.

Lets you improve picture quality when viewing DVDs.

Audio

Speaker Settings

You can set the speaker options.

04 Settings

Equaliser

Smart Volume

Speaker

Selection

Audio Return

Channel

Digital Output

Dynamic

Range

Control

Let you configure the Equaliser settings manually.

Lets you set the product so that the volume remains stable when a scene change occurs or when you change the channel.

Lets you select which speakers you want active, either the TV's speakers or the Home theater's speakers.

Lets you direct the sound from the TV to the Home Cinema speakers. Requires an HDMI connection and an Audio Return Channel (ARC) compatible TV.

• When Audio Return Channel set to on, use HDMI Cable to connect the product to the TV. At this time, optical input does not work.

• When Audio Return Channel set to auto, use HDMI Cable to connect the product to the TV. At this time, ARC and optical input is selected automatically.

Let you set the Digital Output to match the capabilities of the AV receiver you’ve connected to the product. For more details, please refer to the digital output selection table. (See page 56)

Lets you apply dynamic range control to Dolby Digital, Dolby Digital Plus, and Dolby True HD audio.

Auto: Automatically controls the dynamic range of Dolby

TrueHD audio, based on information in the Dolby TrueHD soundtrack. Also turns dynamic range control on for Dolby Digital and Dolby Digital Plus.

Off: Leaves the dynamic range uncompressed, letting you

hear the original sound.

On: Turns dynamic range control on for all three Dolby

formats. Quieter sounds are made louder and the volume of loud sounds is reduced.

Audio Sync

audio delay so that the audio syncs with the video. You can set the delay between 0 and 300 milliseconds.

When the product is attached to a digital TV, lets you adjust the

English 25

HT-E8200_XU_0315.indd 25HT-E8200_XU_0315.indd 25 2012-03-15 오후 1:11:022012-03-15 오후 1:11:02

Settings

Network

Network Settings

Network

Status

Wi-Fi Direct

Soft AP

AllShare Settings

Device Name

BD-Live

Settings

For more information about Network Settings and network functions, see "Networks and the Internet" starting on page 29.

Let you check whether a connection to the network and the Internet have been established.

Lets you connect a Wi-Fi Direct device to the product using a Peer-to-Peer network, without a wireless router. You can use the device to control the product.

Lets you connect other types of Wi-Fi devices to the product wirelessly. Requires that you create a security key which you must enter into the other Wi-Fi devices when you are connecting them to the network.

Lets you permit external devices such as smart phones to connect to the product and share content with or control the product.

Lets you assign an identifying name to the product. You use this name to identify the product when you are connecting external Wi-Fi devices (smart phones, tablets, etc.) to it.

Lets you allow, limit, or prohibit an Internet connection for the BD-Live service.

26 English

HT-E8200_XU_0315.indd 26HT-E8200_XU_0315.indd 26 2012-03-15 오후 1:11:032012-03-15 오후 1:11:03

System

Initial Settings

Device

Manager

Lets you re-run the Initial Settings procedure. See page 21 for details.

You can connect a wireless USB keyboard or mouse to the USB port on the side of the product.

Keyboard Settings: Lets you configure a wireless USB

keyboard connected to the product.

NOTE |

You can use the keyboard only when a QWERTY keyboard screen or

window appears in the Web Browser.

Mouse Settings: Lets you configure a wireless USB mouse

connected to the product. You can use the mouse in the product's menu in the same way you use a mouse on your PC.

To use a mouse with the product's menu:

product

1 . Connect the USB mouse to the

2 . Click the primary button you selected in Mouse Settings.

The Simple Menu appears.

3 . Click the menu options you want. |

NOTE |

Depending on the model of the USB HID keyboard and mouse may not

be compatible with your product. Some HID keyboard keys may not work. Wired USB keyboards are not supported. Some applications may not be supported. If a wireless HID Keyboard does not operate because of interference,

move the keyboard closer to the product.

04 Settings

Anynet+ is a convenient function that offers linked operations with other Samsung products that have the Anynet+ feature

Anynet+

(HDMI-CEC)

and lets you control those products with one Samsung TV remote. To operate this function, you must connect this product to an Anynet+ Samsung TV using an HDMI cable.

You can select the language you prefer for the On-Screen

Language

menu, disc menu, subtitles, etc.

• The language you select for the disc menu, disc audio, or subtitles will only appear if it is supported on the disc.

English 27

HT-E8200_XU_0315.indd 27HT-E8200_XU_0315.indd 27 2012-03-15 오후 1:11:032012-03-15 오후 1:11:03

Settings

Security

General

The default PIN is 0000. Enter the default PIN to access the security function if you haven't created your own password.

BD Parental Rating: Prevents playback of Blu-ray Discs

with a rating equal to or above a specific age rating you enter unless the PIN is entered.

DVD Parental Rating: Prevents playback of DVDs with a

rating above a specific numerical rating you select unless the PIN is entered.

Change PIN: Change the 4-digit PIN used to access

security functions.

If you forget your PIN

1 . Remove any disc or USB storage device. 2 . Press and hold the 5 button on the front panel for 5

seconds or more. All settings will revert to the factory settings.

NOTE |

When the factory default settings are restored, all the user stored BD

data will be deleted.

You can specify the display brightness and time zone.

Front Display: Lets you change the brightness of the front

panel.

Time Zone: You can specify the time zone that is applicable

to your area.

Menu Transparency: Adjust the transparency of the menu

box.

DivX® Video

On Demand

Support

28 English

HT-E8200_XU_0315.indd 28HT-E8200_XU_0315.indd 28 2012-03-15 오후 1:11:042012-03-15 오후 1:11:04

Software

Update

Contact

Samsung

Remote

Management

Reset

View DivX® VOD Registration Codes to purchase and play DivX® VOD contents.

For more information about the Software Update function, see "Upgrading Software" on page 33.

Provides contact information for assistance with your product.

When activated, lets Samsung Call Centre agents diagnose and fix problems with the product remotely. Requires an active Internet connection. Remote Management service might not be available in some countries.

All settings will revert to the default except for the network and Smart Hub settings. The default security password is

0000.

Networks and the Internet

When you connect this product to a network, you can use network based applications and functions such as Smart Hub and BD-LIVE, and upgrade the product's software through the network connection. For more information about accessing and using Internet services, see the Network Services chapter of this manual on pages 49~51. Instructions for configuring the network connection start below.



Wired - Manual

If you have a static IP address or the Automatic procedure does not work, you'll need to set the Network Settings values manually.

After following Steps 1 to 3 above: 1 . Select Start in the Network Settings screen,

and then press the E button. The Network Status screen appears. The product attempts to verify the network connection and fails.

04 Settings

Configuring Your Network Connection

Before you begin, contact your ISP to find out if your IP address is static or dynamic. If it is dynamic, and you have a wired or wireless network, we recommend using the Automatic configuration procedures described below.

If you are connecting to a wired network, connect the product to your router using a LAN cable before you start the configuration procedure.

If you are connecting to a wireless network, disconnect any wired network connection before you begin.

To begin configuring your network connection, follow these steps:

1 . In the Home screen, select Settings, and

then press the E button.

2 . Select Network, and then press the E

button.

3 . Select Network Settings, and then press the

button.

4 . Go to the instructions for Wired networks

starting below or the instructions for Wireless networks starting on page 30.

Wired Network



Wired – Automatic

After following Steps 1 to 3 above: 1 . Select Start in the Network Settings screen,

and then press the E button. The product detects the wired connection, verifies the network connection and then connects to the network.

Network Settings

Wired network connection failed.

Unable to connect to the network. Try the following: check if your IP address is set correctly in IP Settings. Contact your Internet service provider for more information.

MAC Address XX:XX:XX:XX:XX:XX IP Address 0.0.0.0 Subnet Mask 0.0.0.0 Gateway 0.0.0.0 DNS Server 0.0.0.0

IP Settings

Retry

2 . Select IP Settings on the right of the screen,

and then press E button. The IP Settings screen appears.

3 . Select the IP Mode field, and then set it to

Manual.

4 . Use the number keypad on your remote to

enter the Network values. Use the ▲▼◄► buttons on the remote to move from entry field to entry field.

NOTE

You can get these values from your Internet provider. You

can also view these values on most Windows computers. For instructions, see "Getting the Network Settings Values." on this page.

5 . When done, highlight OK, and then press

button. The product verifies the network

connection and then connects to the network.

< Getting the Network Settings Values >

You can view your Network Settings values on most Windows computers. To view the Network Settings values, follow these steps:

• Windows XP 1 . Right click the Network icon on the bottom

right of the Windows desktop.

English 29

HT-E8200_XU_0315.indd 29HT-E8200_XU_0315.indd 29 2012-03-15 오후 1:11:042012-03-15 오후 1:11:04

Settings

2 . In the pop-up menu, click Status. 3 . On the dialog that appears, click the Support

tab.

4 . On the Support tab, click the Details button. 5 . The Network settings are displayed.

• Windows 7 1 . Click the Network icon on the bottom right of

the Windows desktop.

2 . In the pop-up menu, click Network and

Sharing Centre.

3 . On the dialog that appears, click the Local

Area Connection or Wireless Network Connection depending on your network connection.

4 . On the Support tab, click the Details button.

The Network settings are displayed.

NOTE

Depending on your Windows version, the information may

differ.

Wireless Network

You can setup a wireless network connection in three ways:

- Wireless Automatic

- Wireless Manual

- WPS(PBC)

When you configure the wireless network connection, any wireless network devices currently connected through the product or, if applicable, the product's current wired connection, will be disconnected.



Wireless (General) - Automatic

After following Steps 1 to 3 in "Configuring Your Network Connection" on page 29.

1 . Select Start in the Network Settings screen,

and then press the E button. The product searches for and then displays a list of the available networks.

Network Settings

Select your wireless router from the list.

iptime23

ELT

JSY

KT_WLAN_C361

Mirhenge_edu

SO070VOIP

1/10

Refresh

WPS(PBC)

Cancel

2 . Select the desired network, and then press

the E button.

3 . Select Next, and then press the E button

again.

4 . On the Security screen, enter your network's

Security Code or Pass Phrase. Enter numbers directly using the number buttons on your remote control. Enter letters by selecting a letter with an arrow button, and then pressing E button.

5 . When done, select Next at the right of the

screen. The product verifies the network connection and then connects to the network.

NOTE

You should be able to find the Security Code or Pass

Phrase on one of the set up screens you used to set up your router or modem.



Wireless (General) - Manual

If you have a static IP address or the Automatic procedure does not work, you'll need to set the Network Settings values manually.

After folloiwng Steps 1 to 3 in "Configuring Your Network Connection" on page 29.

1 . Select Start in the Network Settings screen,

and then press the E button. The product searches for and then displays a list of the available networks.

2 . Select the desired network or the Add

Network, and then press the E button.

3 . Select Next, and then press the E button

again.

30 English

HT-E8200_XU_0315.indd 30HT-E8200_XU_0315.indd 30 2012-03-15 오후 1:11:062012-03-15 오후 1:11:06

+ 214 hidden pages