Samsung HT-E453 User Manual

HT-E450

HT-E453

HT-E455

Digital Home

Entertainment System

user manual

Imagine the possibilities

Thank you for purchasing this Samsung product. To receive more complete service,

please register your product at

www.samsung.com/register

Safety Information

Safety Warnings

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK).

NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

		CAUTION
		RISK OF ELECTRIC SHOCK
		DO NOT OPEN
This symbol indicates “dangerous voltage”	CAUTION : TO PREVENT ELECTRIC			This symbol indicates important
inside the product that presents a risk of	SHOCK, MATCH WIDE BLADE OF PLUG TO			instructions accompanying the
electric shock or personal injury.	WIDE SLOT, FULLY INSERT.			product.

WARNING

•To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

CAUTION

•Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

•The Mains plug is used as a disconnect device and shall stay readily operable at any time.

•This apparatus shall always be connected to an AC outlet with a protective grounding connection.

•To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.

CLASS 1	LASER PRODUCT
KLASSE 1	LASER PRODUKT
LUOKAN 1	LASER LAITE
KLASS 1	LASER APPARAT
PRODUCTO	LÁSER CLASE 1

CLASS 1 LASER PRODUCT

This Compact Disc player is classified as a CLASS 1 LASER product.

Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

CAUTION

•INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED, AVOID EXPOSURE TO BEAM.

2 English

Precautions

•Ensure that the AC power supply in your house complies with the identification sticker located on the back of your product.

•Install your product horizontally, on a suitable base (furniture), with enough space around it for ventilation (7.5~10cm).

•Do not place the product on amplifiers or other equipment which may become hot. Make sure the ventilation slots are not covered.

•Do not stack anything on top of the product.

•Before moving the product, ensure the Disc Insert Hole is empty.

•In order to disconnect the product completely from the power supply, remove the AC plug from the wall outlet, especially when left unused for a long period of time.

•During thunderstorms, disconnect the AC plug from the wall outlet. Voltage peaks due to lightning could damage the product.

•Do not expose the product to direct sunlight or other heat sources. This could lead to overheating and malfunction of the product.

•Protect the product from moisture, and excess heat or equipment creating strong magnetic or electric fields (i.e. speakers.).

•Disconnect the power cable from the AC supply if the product malfunctions.

•Your product is not intended for industrial use. Use of this product is for personal use only.

•Condensation may occur if your product or disc has been stored in cold temperatures. If transporting the product during the winter, wait approximately 2 hours until the product has reached room temperature before using.

•The batteries used with this product contain chemicals that are harmful to the environment. Do not dispose of batteries in the general household trash.

Accessories

Check for the supplied accessories below.

	Video Cable	FM Antenna	User manual	Remote Control/Batteries (AAA
				size)

English 3

Safety Information

Cautions on Handling and Storing Discs

Small scratches on the disc may reduce sound and picture quality or cause skipping.

Be especially careful not to scratch discs when handling them.

Holding discs

•Do not touch the playback side of the disc.

•Hold the disc by the edges so that

fingerprints will not get on the surface.

• Do not stick paper or tape on the disc.

Disc Storage

•Do not keep in direct sunlight

•Keep in a cool ventilated area

•Keep in a clean Protection jacket. Store vertically.

NOTE

`` Do not allow the discs to become contaminated with dirt. `` Do not load cracked or scratched discs.

Handling and Storing Discs

If you get fingerprints or dirt on the disc, clean it with a mild detergent diluted in water and wipe with a soft cloth.

•When cleaning, wipe gently from the inside to the outside of the disc

NOTE

`` Condensation may form if warm air comes into contact with cold parts inside the product. When condensation forms inside the product, it may not operate correctly. If this occurs, remove the disc and let the product stand for 1 or 2 hours with the power on.

Licence

•Dolby and the double-D symbol are registered trademarks of Dolby Laboratories.

•Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS, the Symbol, & DTS and the Symbol together are registered trademarks & DTS Digital Surround and the DTS logos

are trademarks of	software. © DTS, Inc.
All Rights Reserved.
• ABOUT DIVX	video format created
by DivX,LLC,a	. This is an

official DivX Certified® device that plays DivX video. Visit divx.com for more information and software tools to convert your files into DivX videos.

•ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod.divx.com for more information on how to complete your registration.

•DivX Certified® to play DivX® video, including premium content.

•DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license.

• Covered by one or	U.S. patents :
7,295,673; 7,460,668;	.

•HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

•This item incorporates copy protection technology that is protected by U.S. patents and other intellectual property rights of Rovi Corporation. Reverse engineering and disassembly are prohibited.

•This product uses some software programs which are distributed under the Independent JPEG Group.

•This product uses some software programs which are distributed under the OpenSSL Project.

Copyright

© 2012 Samsung Electronics Co., Ltd. All rights reserved.

Copy Protection

•Many DVD discs are encoded with copy protection. Because of this, you should only connect your product directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy-protected DVD discs.

4 English

Contents

SAFETY INFORMATION

2

GETTING STARTED

7

CONNECTIONS

15

SETUP

22

2Safety Warnings

3Precautions

3Accessories

4Cautions on Handling and Storing Discs

4	Licence
4	Copyright
4	Copy Protection

7 Icons that will be used in manual

7 Disc Types and Characteristics

11Description

11Front Panel

12Rear Panel

13Remote control

15 Connecting the Speakers

18 Connecting the Video Out to your TV

20 Connecting the FM Antenna

20 Connecting Audio from External Components

22Before Starting (Initial Settings)

22Setting the Setup menu

23Display

23	TV Aspect
23	BD Wise

23Resolution

23HDMI Format

23Video Out Signal

24Audio

24Speaker Setting

25DRC (Dynamic Range Compression)

25AUDIO SYNC

26Speaker Selection

26

User EQ

26Audio Return Ch.

26System

26Initial Settings

26DivX(R) Registration

26DivX(R) Deactivation

27Language

27 Security

27 Parental Rating

27 Change Password

27 Support

27 Product Information

ENGLISH

English 5

Contents

BASIC FUNCTIONS

28

ADVANCED FUNCTIONS

36

28 Disc Playback

28Audio CD(CD-DA)/MP3/WMA Playback

29JPEG File Playback

29 Using the Playback Function

33 Sound Mode

35Listening to Radio

36USB Function

36 USB Recording

OTHER INFORMATION

37 Troubleshooting

3739 Specifications

41 OpenSSL License

•Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance.

•An administration fee may be charged if either

a.an engineer is called out at your request and there is no defect in the product (i.e. where you have failed to read this user manual)

b.you bring the unit to a repair centre and there is no defect in the product (i.e. where you have failed to read this user manual).

•The amount of such administration charge will be advised to you before any work or home visit is carried out.38 Language code list

6 English

Getting Started

Icons that will be used in manual

Make sure to check the following terms before reading the user manual.

Icon	Term	Definition
		This involves a function
d		available with DVD-Video or
	DVD	DVD±R/±RW discs that
		have been recorded and
		finalised in Video Mode.
B		This involves a function
	CD	available with a data CD
		(CD DA, CD-R/-RW).
A		This involves a function
	MP3	available with CD-R/-RW
		discs.
G		This involves a function
	JPEG	available with CD-R/-RW
		discs.
D		This involves a function
	DivX	available with MPEG4 discs.
		(DVD±R/±RW, CD-R/-RW)
!		This involves a case where a
	CAUTION	function does not operate or
		settings may be cancelled.
		This involves tips or instructions
	NOTE	on the page that help each
		function operate.
	Shortcut	This function provides direct and
		easy access pressing the button
	Key
		on the remote control.

								01
								Getting
	Disc Types and Characteristics
	Region Code							Started
	The product and the discs are coded by region. These
	regional codes must match in order for the disc to play. If the
	codes do not match, the disc will not play.
	Disc Type	Region				Area
				Code
						The U.S., U.S. territories and
				1
						Canada
						Europe, Japan, the Middle East,
				2
						Egypt, South Africa, Greenland
						Taiwan, Korea, the Philippines,
				3
	DVD-VIDEO					Indonesia, Hong Kong
						Mexico, South America, Central
				4		America, Australia, New Zealand,
						Pacific Islands, Caribbean
						Russia, Eastern Europe, India,
				5		most of Africa, North Korea,
						Mongolia
						China
				6

English 7

Getting Started

Disc types that can be played

	Disc Types &	Recorded	Disc	Max. Playing Time
	Mark (Logo)	Signals	Size
				Approx. 240 min.
			12 cm	(single-sided)
		AUDIO		Approx. 480 min.
				(double-sided)
		+
				Approx. 80 min.
	DVD-VIDEO	VIDEO
			8 cm	(single-sided)
				Approx. 160 min.
				(double-sided)
			12 cm	74 min.
		AUDIO
	AUDIO-CD		8 cm	20 min.
		AUDIO	12 cm	-
		+
	DivX
			8 cm	-
		VIDEO

Do not use the following type of discs!

•LD, CD-G, CD-I, CD-ROM, DVD-ROM and DVD-RAM discs cannot be played on this product. If such discs are played, a <WRONG DISC FORMAT> message appears on the TV screen.

•DVD discs purchased abroad may not play on this product.

If such discs are played, a <Wrong Region. Please check Disc.> message appears on the TV screen.

Disc Types And Disc Format

This product does not support Secure (DRM) Media files.

CD-R Discs

•Some CD-R discs may not be playable depending on the disc recording device (CD-Recorder or PC) and the condition of the disc.

•Use a 650MB/74 minute CD-R disc.

Do not use CD-R discs over 700MB/80 minutes as they may not be played back.

•Some CD-RW (Rewritable) media, may not be playable.

•Only CD-Rs that are properly "closed" can be fully played. If the session is closed but the disc is left open, you may not be able to fully play the disc.

CD-R MP3 Discs

•Only CD-R discs with MP3 files in ISO 9660 or Joliet format can be played.

•MP3 file names should contain no blank spaces or special characters (. / = +).

•Use discs recorded with a compression/ decompression data rate greater than 128Kbps.

•Only files with the ".mp3" and ".MP3" extensions can be played.

•Only a consecutively written multisession disc can be played. If there is a blank segment in the Multisession disc, the disc can be played only up to the blank segment.

•If the disc is not closed, it will take longer to begin playback and not all of the recorded files may be played.

•For files encoded in Variable Bit Rate (VBR) format, i.e. files encoded in both low bit rate and high bit rate (e.g., 32Kbps ~ 320Kbps), the sound may skip during playback.

•A maximum of 500 tracks can be played per CD.

•A maximum of 300 folders can be played per CD.

CD-R JPEG Discs

•Only files with the "jpg" extensions can be played.

•If the disc is not closed, it will take longer to start playing and not all of the recorded files may be played.

•Only CD-R discs with JPEG files in ISO 9660 or Joliet format can be played.

•JPEG file names should be 8 characters or less in length and contain no blank spaces or special characters (. / = +).

•Only a consecutively written multisession disc can be played. If there is a blank segment in the multisession disc, the disc can be played only up to the blank segment.

•A maximum of 999 images can be stored on a folder.

•When playing a Kodak/Fuji Picture CD, only the JPEG files in the picture folder can be played.

•Picture discs other than Kodak/Fuji Picture CDs may take longer to start playing or may not play at all.

8 English

DVD±R/±RW, CD-R/RW Discs

•Software updates for incompatible formats are not supported.

(Example : QPEL, GMC, resolutions higher than 800 x 600 pixels, etc.)

•If a DVD-R/-RW disc has not been recorded properly in DVD Video format, it will not be playable.

Supported Formats (DivX)

This product only supports the following media formats. If both video and audio formats are not supported, the user may experience problems such as broken images or no sound.

Supported Video Formats

Format		Supported Versions
AVI		DivX3.11~DivX6.8
WMV		V1/V2/V3/V7
Supported Audio Formats
Format		Bit Rate		Sampling
				Frequency
MP3		80~320kbps		44.1khz
WMA		56~128kbps
AC3		128~384kbps		44.1/48khz
DTS		1.5Mbps		44.1khz

•DivX files, including audio and video files, created in the DTS format can only support up to 6Mbps.

•Aspect Ratio : this product supports up to 720x576 pixels. TV screen resolutions higher than 800 will not be supported.

•When you play a disc whose sampling frequency is higher than 48khz or 320kbps, you may experience shaking on the screen during playback.

•Sections with a high frame rate might not be played while playing a DivX file.

•Since this product only provides encoding formats authorized by DivX Networks, Inc., a DivX file created by the user might not play.

Started Getting 01

English 9

Getting Started

Notes on USB connection

Supported devices: USB storage media, MP3 player, digital camera

1)If a folder or file name is longer than 10 characters, it may not properly display or operate.

2)A subtitle file bigger than 300KB may not be properly displayed.

3)A certain USB/digital camera device, USB card reader is not supported.

4)FAT16 and FAT32 file systems are supported.

5)Photo (JPEG), music (MP3, WMA) and video file should have their names in Korean or English. Otherwise, the file may not played.

6)Connect directly to the product's USB port. Connecting through another cable may raise problems with USB compatibility.

7)Inserting more than one memory device to a multi-card reader may not operate properly.

8)PTP protocol for digital camera is not supported.

9)Do not disconnect USB device during a "Reading" process.

10)Bigger the image resolution, the longer the delay to displaying.

11)DRM applied MP3/WMA or video files downloaded from a commercial site are not played back.

12)External HDD device is not supported.

13)The maximum current supported by the USB port for an external device is 500 mA (at 5V DC).

14) Supported file formats

	Format	Still	Music			Movie
		Picture
	File name	JPG	MP3	WMA	WMV		DivX
	File	JPG	.MP3	.WMA	.WMV		.AVI
	extension	.JPEG
	Bit rate	–	80~320	56~128	4Mbps		4Mbps
			kbps	kbps
	Version	–	–	V8	V1,V2,		DivX3.11~
					V3,V7		DivX6.8
	Pixel	640x480	–	–	720x576
	Sampling	–	44.1kHz	44.1kHz	44.1KHz~ 48KHz
	Frequency

10 English

Description

Front Panel

1

2

3

4

5

6

7

8

9

10

5V 500mA

AUX IN 1

11

Started Getting 01

	1	DISC TRAY			Insert disc here.
	2	AUX IN 1 CONNECTOR			Connect external components such as an MP3 player.
	3	DISPLAY			Displays the playing status, time, etc.
					Connect here and play files from external USB storage devices such as MP3
	4	USB PORT			players, USB flash memory, etc.
					The USB memory that requires high power (more than 500mA at 5V) may
					not be supported. (except iPod/iPhone which is compatible with 1A at 5V).
	5	OPEN/CLOSE BUTTON (		)	Opens and closes the disc tray.
	6	FUNCTION BUTTON (		)	The mode switches as follows :
					DVD/CD D.IN AUX 1 AUX 2 USB FM
	7	STOP BUTTON (	)		Stops disc playback.
	8	PLAY / PAUSE BUTTON (		)	Plays a disc or pauses playback.
	9	VOLUME CONTROL BUTTON ( , )			Volume adjustment.
	10	POWER BUTTON (	)		Turns the product on and off.
	11	REMOTE CONTROL SENSOR			Detects signals from the remote control.

English 11

Getting Started

Rear Panel

1	2	3
	SPEAKERS OUT
FA NET
(Only For Service)
	SURROUND	SUBWOOFER	SURROUND

4 5 6 7 8

AUX IN 2	VIDEO
	OUT
	FM ANT	HDMI OUT
	OPTICAL
	DIGITAL
	AUDIO IN

	1	FA NET (Only for Service)	Used for the service repair.
	2	COOLING FAN	The fan always revolves when the power is on. Ensure a minimum of 10cm of clear
			space on all sides of the fan when installing the product.
	3	SPEAKERS OUTPUT CONNECTORS	Connect the front, center,surround speakers and subwoofer.
	4	AUX IN 2 JACKS	Connect to the 2CH Analog output of an external device (such as a VCR).
	5	VIDEO OUT JACK	Connect your TV's Video Input jack (VIDEO IN) to the VIDEO OUT jack.
	6	EXTERNAL DIGITAL OPTICAL IN JACK	Use this to connect external equipment capable of digital output.
		(DIGITAL AUDIO IN)
	7	FM ANTENNA JACK	Connect the FM antenna.
	8	HDMI OUT JACK	Using an HDMI cable, connect this HDMI output jack to the HDMI input jack
			on your TV for the best quality picture.

12 English

Remote control

Tour of the Remote Control

Turn the product on and off. If you want to change to TV mode, press the TV button.

If you want to change to Home Theater, press the DVD button.

Press numeric buttons to operate options.

Select the desired Dolby Pro Logic II audio mode.

Press to skip backwards or forwards.

Press to stop/play a disc.

Cut off the sound temporarily.

Adjust the volume.

Brings up the product's setup menu. Press to check the disc menu.

Used to change the audio/subtitle language, angle etc.

Select on-screen menu items and change menu value.

Return to the previous menu.

Allow access to common functions of the DVD Home Theater such as navigating the Photo List.

Adjust the brightness of Display.

Used to turn on/off GIGA Sound function. Used to adjust the level of the subwoofer.

Press to preset FM stations.

TV

SOURCE

VOL

REPEAT

TUNING

/ CH

DISC MENU

HOME

TITLE MENU

GIGA

This is mode selection button. or

Press to select TV's video mode.

Set a Sleep time to shut off the Product.

To open and close the disc tray.

Select the desired DSP/EQ audio mode.

Press to search backwards or forwards.

Press to pause a disc.

Search for active FM stations and change channels.

Allows you to repeat a title, chapter, track or disc.

Use this to enter the Title menu.

Display current disc(file) status.

Press this to exit the menu.

Select the desired P.BASS or MP3

Enhancement setting.

Regulate and stabilize the volume level against a drastic volume change.

Used to start USB recording.

Select MONO or STEREO for radio broadcasting.

Started Getting 01

English 13

Getting Started

Installing batteries in the Remote Control

* Battery size: AAA

NOTE

`` Place batteries in the remote control so they match the polarity : (+) to (+) and (–) to (–).

`` Always replace both batteries at the same time. `` Do not expose the batteries to heat or flame.

`` The remote control can be used up to approximately 23 feet (7 meters) in a straight line.

Setting the Remote Control

You can control certain functions of your TV with this remote control.

When operating a TV with the remote control

1.Press the TV button to set the remote control to TV mode.

2.Press the POWER button to turn on the TV.

3.While holding down the POWER button, enter the code corresponding to your brand of TV.

•If there is more than one code listed for your TV in the table, enter one at a time to determine which code works.

•Example : For a Samsung TV

While holding down the POWER button, use the number buttons to enter 00, 15, 16, 17 and 40.

4.If the TV turns off, the setting is complete.

•You can use the TV POWER, VOLUME, CHANNEL, and Numeric buttons (0~9).

NOTE

`` The remote control may not work or some operations may not be possible with some brands of TVs.

`` The remote control will work on a Samsung TV by default.

TV Brand Code List

	Brand	Code
	Admiral	56, 57, 58
	(M.Wards)
	A Mark	01, 15
		01, 02, 03, 04, 05, 06,
	Anam	07, 08, 09, 10, 11,
		12, 13, 14
	AOC	01, 18, 40, 48
	Bell & Howell	57, 58, 81
	(M.Wards)
	Brocsonic	59, 60
	Candle	18
	Cetronic	03
	Citizen	03, 18, 25
	Cinema	97
	Classic	03
	Concerto	18
	Contec	46
	Coronado	15
	Craig	03, 05, 61, 82, 83, 84
	Croslex	62
	Crown	03
	Curtis Mates	59, 61, 63
	CXC	03
		02, 03, 04, 15, 16, 17, 18,
	Daewoo	19, 20, 21, 22, 23, 24,	25,
		26, 27, 28, 29, 30, 32, 34,
		35, 36, 48, 59, 90
	Daytron	40
	Dynasty	03
	Emerson	03, 15, 40, 46, 59, 61,
		64, 82, 83, 84, 85
	Fisher	19, 65
	Funai	03
	Futuretech	03
	General	06, 40, 56, 59, 66,
	Electric (GE)	67, 68
	Hall Mark	40
	Hitachi	15, 18, 50, 59, 69
	Inkel	45
	JC Penny	56, 59, 67, 86
	JVC	70
	KTV	59, 61, 87, 88
	KEC	03, 15, 40
	KMC	15
	LG (Goldstar)	01, 15, 16, 17, 37, 38,
		39, 40, 41, 42, 43, 44
	Luxman	18
	LXI (Sears)	19, 54, 56, 59, 60, 62,
		63, 65, 71
	Magnavox	15, 17, 18, 48, 54, 59,
		60, 62, 72, 89
	Marantz	40, 54
	Matsui	54
	MGA	18, 40
	Mitsubishi/	18, 40, 59, 60, 75
	MGA

	Brand	Code
	MTC	18
	NEC	18, 19, 20, 40, 59, 60
	Nikei	03
	Onking	03
	Onwa	03
	Panasonic	06, 07, 08, 09, 54, 66,
		67, 73, 74
	Penney	18
	Philco	03, 15, 17, 18, 48, 54,
		59, 62, 69, 90
	Philips	15, 17, 18, 40, 48,
		54, 62, 72
	Pioneer	63, 66, 80, 91
	Portland	15, 18, 59
	Proton	40
	Quasar	06, 66, 67
	Radio Shack	17, 48, 56, 60, 61, 75
	RCA/	18, 59, 67, 76, 77, 78,
	Proscan	92, 93, 94
	Realistic	03, 19
	Sampo	40
	Samsung	00, 15, 16, 17, 40, 43, 46,
		47, 48, 49,
	Sanyo	19, 61, 65
	Scott	03, 40, 60, 61
	Sears	15, 18, 19
	Sharp	15, 57, 64
	Signature
	2000	57, 58
	(M.Wards)
	Sony	50, 51, 52, 53, 55
	Soundesign	03, 40
	Spectricon	01
	SSS	18
	Sylvania	18, 40, 48, 54, 59,
		60, 62
	Symphonic	61, 95, 96
	Tatung	06
	Techwood	18
	Teknika	03, 15, 18, 25
	TMK	18, 40
	Toshiba	19, 57, 63, 71
	Vidtech	18
	Videch	59, 60, 69
	Wards	15, 17, 18, 40, 48,
		54, 60, 64
	Yamaha	18
	York	40
	Yupiteru	03
	Zenith	58, 79
	Zonda	01
	Dongyang	03, 54

14 English

Connections

This section involves various methods of connecting the product to other external components. Before moving or installing the product, be sure to turn off the power and disconnect the power cord.

Connecting the Speakers

Position of the product

Place it on a stand or cabinet shelf, or under the

SW

TV stand.

Selecting the Listening Position

The listening position should be located about 2.5 to 3 times the distance of the TV's screen size away from the TV.

Example : For 32" TV's 2~2.4m For 55" TV's 3.5~4m

			Place these speakers in front of your listening position, facing inwards (about 45°)
	Front Speakers ei		toward you. Place the speakers so that their tweeters will be at the same height
			as your ear. Align the front face of the front speakers with the front face of the
			center speaker or place them slightly in front of the center speakers.
	Center Speaker f		It is best to install it at the same height as the front speakers. You can also install it
			directly over or under the TV.
			Place these speakers to the side of your listening position. If there isn't enough
			room, place these speakers so they face each other. Place them about 60 to
	Surround Speakershj		90cm above your ear, facing slightly downward.
			Unlike the front and center speakers, the surround speakers are used to
			* handle mainly sound effects and sound will not come from them all the time.
	Subwoofer g		The position of the subwoofer is not so critical. Place it anywhere you like.
	!!CAUTION
	``	Do not let children play with or near the speakers. They could get hurt if the speaker falls.
	``	When connecting the speaker wires to the speakers, make sure that the polarity (+/–­) is correct.
	``	Keep the subwoofer out of the reach of children so as to prevent them from inserting their hands or alien
		substances into the duct (hole) of the subwoofer.
	``	Do not hang the subwoofer on the wall through the duct (hole).

NOTE

`` If you place a speaker near your TV set, screen colour may be distorted because of the magnetic field generated by the speaker. If this occurs, place the speaker away from your TV set.

Connections 02

English 15

Connections

Speaker Components

HT-E450

(L)(R)

(L)(R)

FRONT			SURROUND		CENTER	SUBWOOFER
Speaker Components					Assembled Speakers
HT-E453					HT-E453
(L) (R)		(L)	(R)
						CENTER SPEAKER
FRONT STAND		SURROUND		CENTER	
SCREW (5×15): 8EA	STAND BASE			SPEAKER	FRONT	SURROUND	SUBWOOFER
			SUBWOOFER CABLE		SPEAKER	SPEAKER
HT-E455					HT-E455
(L) (R)
			SCREW (5×15): 16EA

CENTER SPEAKER

FRONT STAND

(L) (R)			
		CENTER
SURROUND	STAND BASE	SUBWOOFER	FRONT/SURROUND SPEAKER	SUBWOOFER

SPEAKER CABLE

NOTE

`` Refer to page 17 to install the Speakers on the Tallboy Stand.

16 English

Installing the Speakers on the Tallboy Stand

*HT-E453 only - Front Speakers

*HT-E455 only - Front/Surround Speakers

1.Turn the Stand Base upside-down and connect it to the Stand.

2.Insert three screws (5*15, For connecting Stand & Stand Base) clockwise

into the three holes marked using a screwdriver as shown in the illustration. !!CAUTION : When you use a torque screwdriver, be careful not to put

excessive force. Otherwise, it runs idle or can be damaged. (torque screwdriverbelow 15 kg.f.cm)

3.Straighten a supplied speaker wire and put in the hole on the centre of Stand Base.

4.Connect the upper Speaker to the assembled Stand.

5.Insert another large screw (5*15, For connecting Speaker & Stand) clockwise into the hole on the rear of the speaker using a screwdriver.

6.This is the appearance after the speaker is installed. Follow this steps to install other speaker.

1 Stand Base	2
Stand
3	4

Speaker

Stand

5

6

Connecting The Speakers

	1.	Press down the terminal tab on the back of the speaker. (HT-E453/E455
		Only)
	2.	Insert the black wire into the black terminal (–) and the red wire into the red
		terminal (+), and then release the tab.(HT-E453/E455 Only)	Black	Red
	3.	Connect the connecting plugs to the back of the product by matching the
		colours of the speaker plugs to the speaker jacks.

In case of HT-E450

Center Speaker

Front Speaker (R)

FA NET

(Only For Service)

SPEAKERS OUT

		Front Speaker (L)
AUX IN 2	VIDEO
	OUT
	FM ANT	HDMI OUT

OPTICAL

		DIGITAL
SURROUND	SUBWOOFER SURROUND	AUDIO IN

Surround Speaker (R)	Surround Speaker (L)
	Subwoofer

* Refer to page 16 for the speakers of HT-E453/E455.

Connections 02

English 17

Connections

Connecting the Video Out to your TV

Choose one of the two methods for connecting to a TV.

METHOD2 (supplied)

ERS OUT

AUX IN 2

FM ANT

HDMI OUT

BWOOFER SURROUND

AUDIO IN

METHOD1

METHOD 1 : HDMI

Connect an HDMI cable (not supplied) from the HDMI OUT jack on the back of the product to the HDMI IN jack on your TV.

METHOD 2 : Composite Video

Connect the supplied Video cable from the VIDEO OUT jack on the back of the product to the VIDEO IN jack on your TV.

NOTE

`` Resolutions available for the HDMI output are 576p(480p), 720p,1080i/1080p. See page 23 for the resolution setting.

`` This product operates in Interlace scan mode 576i(480i) for composite output.

`` After making the video connection, set the Video input source on your TV to match the corresponding Video output mode on your product.

Turn this product on first before you set the video input source on your TV. See your TV owner's manual for more information on how to select the TV's Video Input source.

!!CAUTION

`` Do not connect the unit through a VCR. Video signals fed through VCRs may be affected by copyright protection systems and the picture will be distorted on the television.

18 English

HDMI FUNCTION

HDMI Auto Detection Function

If your TV is Samsung TV and it supports CEC function.The product's video output will automatically change to HDMI mode when connecting an HDMI cable while power is on.

• HDMI (High Definition Multimedia Interface)

HDMI is an interface that enables the digital transmission of video and audio data with just a single connector. Using HDMI, the product transmits a digital video and audio signal and displays a vivid picture on a TV having an HDMI input jack.

•HDMI connection description

-HDMI outputs only a pure digital signal to the TV.

-If your TV does not support HDCP (High-bandwidth Digital Content Protection), random noise appears on the screen.

•What is the HDCP?

•HDCP (High-band width Digital Content Protection) is a system for protecting DVD content outputted via HDMI from being copied. It provides a secure digital link between a video source (PC, DVD. etc) and a display device (TV, projector. etc). Content is encrypted at the source device to prevent unauthorized copies from being made.

Using Anynet+(HDMI-CEC)

Anynet+ is a function that enables you to control other Samsung Devices with your Samsung TV's remote control. Anynet + can be used by connecting this product to a SAMSUNG TV using a HDMI Cable. This is only available with SAMSUNG TV's that support Anynet+.

1.Connect the product to a Samsung TV with an HDMI cable. (See page 18)

2.Set the Anynet+ function on your TV. (See the TV instruction manual for more information.)

NOTE

`` The Anynet+ function supports some buttons of the remote control. `` This function is not available if an HDMI cable does not support CEC.

`` Depending on your TV, certain HDMI output resolutions may not work. Please refer to the user’s manual of your TV.

`` Please check the logo (If your TV has an logo, then it supports Anynet+ function.)

Connections 02

English 19

Connections

Connecting the FM Antenna

FM Antenna (supplied)

SPEAKERS OUT		VIDEO
	AUX IN 2
		OUT
		FM ANT	HDMI OUT
		OPTICAL
		DIGITAL
SURROUND SUBWOOFER SURROUND		AUDIO IN

1.Connect the FM antenna supplied to the FM Antenna jack.

2.Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a wall or other rigid surface.

NOTE

`` This product does not receive AM broadcasts.

Connecting Audio from External Components

Audio Out

AUX IN 1	5V 500mA
	AUX IN 1

Audio Cable (not supplied)

AUX1 : Connecting an External Component/MP3 player

Components such as an MP3 Player.

1.Connect AUX IN 1 (Audio) on the front of the product to the Audio Out of the external component/ MP3 player.

2.Press the FUNCTION button to select AUX1 input.

• The mode switches as follows :

DVD/CD D.IN AUX 1 AUX 2 USB FM

20 English

Connecting Audio from External Components

FA NET

(Only For Service)

Audio Cable (not supplied)

If the external analog component has only one Audio Out, connect either left or right.

VCR

AUX 2

SPEAKERS OUT			OUT
White
		AUX IN 2	VIDEO
			FM ANT HDMI OUT
SU OUND SUBWOOFER	SURROUND
Red

Optical Cable

(not supplied)

Set-Top Box

OPTICAL

AUX2 : Connecting an External Analog Component

Analog signal components such as a VCR.

1.Connect AUX IN 2 (Audio) on the back of the product to the Audio Out of the external Analog component.

•Be sure to match the colors of the connecting jacks.

2.Press the FUNCTION button to select AUX 2 input.

•The mode switches as follows :

DVD/CD D.IN AUX 1 AUX 2 USB FM

NOTE

`` You can connect the Video Output jack of your VCR to the TV, and connect the Audio Output jacks of the VCR to this product.

OPTICAL : Connecting an External Digital Component

Digital signal components such as a Cable Box/Satellite receiver (Set-Top Box).

1.Connect the DIGITAL AUDIO IN (OPTICAL) on the back of the product to the Digital Output of the external digital component.

2.Press the FUNCTION button to select D.IN.

•The mode switches as follows :

DVD/CD D.IN AUX 1 AUX 2 USB FM

Connections 02

English 21

Setup

Before Starting (Initial Settings)

1.Press the POWER button when it is plugged in TV for the first time.

Initial Settings screen will be displayed.

Initial settings > On-Screen Language

Select a language for the on-screen displays

English

Nederlands

Français

Deutsch

Italiano

>Move " Select

2.Press the ▲▼ buttons to select the desired language, then press the ENTER button.

3.Press the ▲▼ buttons to select desired TV Aspect, then press the ENTER button.

`` If the HDMI cable is connected to the product, TV aspect does not appear.

NOTE

`` If you have not selected a preferred language in the initial settings, you will see a language selection window next time you turn on the product.

`` Your language selection will apply to all menus: On-Screen Menu, Disc Menu, Audio, Subtitle.

`` If you want to move to the previous screen, press the

A(PREVIOUS) or RETURN button.

`` Once you select a menu language, you can change it by pressing the STOP (@) button on the remote control or the main set for more than 5 seconds in no disc state.

`` When the Initial Settings screen does not appear, refer to the Initial Settings. (see page 26)

Setting the Setup menu

The access step may differ depending on the selected menu. The GUI (Graphical User Interface) in this manual may differ, depending on the firmware version.

DISC MENU

HOME

TITLE MENU

1

3 2 4

1HOME BUTTON : Display the home menu.

2RETURN BUTTON : Return to the previous setup menu.

ENTER / DIRECTION BUTTON

3Move the cursor and select an item. Select the currently selected item. Confirm the setting.

4EXIT BUTTON : Exit the setup menu.

Settings

Function DVD/CD

1.Press the POWER button.

2.Press the _+ buttons to select Settings, then press the ENTER button.

3.Press the ▲▼ buttons to select the desired menu, then press the ENTER button.

4.Press the ▲▼ buttons to select the desired sub-menu, then press the ENTER button.

5.Press the ▲▼ buttons to select the desired item, then press the ENTER button.

6.Press the EXIT button to exit the setup menu.

22 English

Display

You can configure various display options such as the TV Aspect, Resolution, etc.

TV Aspect

Depending on the type of television you have, you may want to adjust the screen setting.

• 4:3 Pan-Scan

Select when you want to see the 16:9 video supplied by the DVD without the black bars on top and bottom, even though you have a TV with a 4:3 ratio screen(extreme left and right portion of the movie picture will be cut off).

• 4:3 Letter Box

Select when you want to see the total 16:9 ratio screen DVD supplies, even though you have a TV with a 4:3 ratio screen. Black bars will appear at the top and bottom of the screen.

• 16:9 Wide

You can view the full 16:9 picture on your widescreen TV.

NOTE

`` When using HDMI, the screen is automatically converted to the 16:9 Wide mode and TV Aspect is deactivated.

`` If a DVD is in the 4:3 ratio, you cannot view it in the wide screen. `` Since DVD discs are recorded in various image formats, they will look different depending on the software, the type of TV, and the

TV aspect ratio setting.

BD Wise

(Samsung products only)

BD Wise is Samsung's latest inter-connectivity feature. When you connect Samsung products with BD-Wise to each other via HDMI, the optimum resolution will be set automatically.

•On : The original resolution of the DVD disc will be output to the TV direct.

•Off : The output resolution will be fixed according to the Resolution previously set, regardless of the resolution of the disc.

NOTE

`` This will optimize the picture quality according to the content (In the DVD disc, etc) that you want to play and the product or your BD Wise-compliant Samsung TV.

`` If you want to change the resolution in BD Wise mode, you must set BD mode to Off in advance.

`` BD Wise will be disabled if the product is connected to a device that does not support BD Wise.

Resolution

Sets the output resolution of the HDMI video signal. The number in 576p(480p), 720p, 1080i and 1080p indicates the number of lines of video.

The i and p indicate interlace and progressive scan, respectively.

•576p(480p) : Outputs 576(480) lines of progressive video.

•720p : Outputs 720 lines of progressive video.

•1080i : Outputs 1080 lines of interlaced video.

•1080p : Outputs 1080 lines of progressive video.

•BD Wise : Automatically sets the optimal resolution when connected via HDMI to a TV with the BD Wise feature. (The BD Wise menu item appears only if BD Wise is set to On.)

NOTE

`` If Composite is connected, the resolution supports only 576i(480i).

`` 1080P may not appear depending on TV.

HDMI Format

You can optimize the color setting from the HDMI output. Select a connected device Type.

•Monitor : Select if connected to a Monitor via HDMI.

•TV : Select if connected to a TV via HDMI.

Video Out Signal

Different countries apply different TV standard. You can select from NTSC or PAL.

•NTSC : You can select the NTSC video format

•PAL : You can select the PAL video format

Setup 03

English 23

Setup

Audio

Speaker Setting

Speaker Size

You can set the Speaker Size of the Center and Surround Speakers, as well as Test Tone in this mode.

Settings

Speaker Setting

Speaker Size
Sound Edit
Delay Time
Test Tone	: Off

" Select ' Return

mMove " Select ' Return

•For the Front, the mode is set to Small.

•For the Subwoofer, the mode is set to Present.

•For the Center and Surround, you can switch the mode to Small or None.

-Small : Select this when using the speakers.

-None :  Select this when no speaker is connected.

NOTE

`` The speaker mode may vary depending on the Dolby Pro Logic and Stereo settings.

Sound Edit

You can adjust the balance and level for each speaker.

Settings	Sound Edit
Front Bal.	dB L	R	dB
Surround Bal.	dB L	R	dB
Center Level			dB
Surround Level			dB
SW Level			dB
	<Change " Select ' Return
	mMove	" Select	' Return

Press the $% buttons to select and adjust the desired speaker.

Press the _+ buttons to adjust the settings.

Adjusting Front/Surround Bal.

`` You can select between 0 and -6.

`` The volume decreases as you move closer to –6.

Adjusting Center/Surround/Subwoofer Level

`` The volume level can be adjusted in steps from +6dB to –6dB.

`` The sound gets louder as you move closer to +6dB and quieter as you get closer to -6dB.

Delay Time

If the speakers cannot be placed at equal distances from the listening position, you can adjust the delay time of the audio signals from the Center and Surround speakers.

You can also set the Test Tone in this mode.

Setting up the Speaker Delay Time

When 5.1CH Surround Sound is played, you can enjoy the best sound if the distance between you and each speaker is the same.

Since the sounds arrive at the listening position at different times depending on the placement of speakers, you can adjust this difference by adding a delay effect to the Center and Surround Speakers.

Settings

Delay Time

Front

Center	:	00ms
Surround	: 00ms
Subwoofer
Test Tone	:	Off

<Change " Select ' Return

mmove " Select ' Return

NOTE

`` The Delay Time menu will be activated only when a 5.1 channel source is played.

`` You can not set Center and Surround in this mode when their Speaker Size is set to NONE.

24 English

Ideal Center

Speaker placement

Ideal Surround

Speaker placement

Place all speakers within this circle.

Df: The distance from Front Speaker

Dc: The distance from Center Speaker

Ds: The distance from Surround Speaker

Setting the Center Speaker

If the distance of Dc is equal to or longer than the distance of Df in the figure, set the mode as 0ms. Otherwise, change the setting according to the table.

Distance

between 0.00m 0.34m 0.68m 1.06m 1.40m 1.76m

Df and Dc

	Delay	00 ms 01 ms 02 ms 03 ms 04 ms 05 ms
	Time

Setting the Surround Speaker

If the distance of Dc is equal to or longer than the distance of Ds in the figure, set the mode as 0ms. Otherwise, change the setting according to the table.

Distance

between 0.00m 1.06m 2.11m 3.16m 3.62m 5.29m

Ds and Dc

	Delay	00 ms 03 ms 06 ms 09 ms 12 ms 15 ms
	Time

NOTE

`` With PL II (Dolby Pro Logic II), the delay time may be different for each mode.

`` With AC-3 and DTS, the delay time can be set between 00 and 15mSEC.

`` The Center channel is only adjustable on 5.1 channel discs.

				03
Test Tone							Setup
	Settings
		Speaker Setting
			Speaker Size
			Sound Edit
			Delay Time
			Test Tone	: On

" Select ' Return

mMove " Select ' Return

Use the Test Tone feature to check the speaker connections.

•Press the _+ buttons to select On.

•The test tone will be sent to Front Left Center

Front Right Surround Right Surround

Left Subwoofer in order.

To stop the test tone, press the ENTER button.

DRC (Dynamic Range Compression)

This feature balances the range between the loudest and quietest sounds. You can use this function to enjoy Dolby Digital sound when watching movies at low volume at night.

• You can select either Full, 6/8, 4/8, 2/8, off.

AUDIO SYNC

Video and audio sync may not match with digital TV. If this occurs, adjust the audio delay time to

match the video

•You can set the audio delay time between 0 ms and 300 ms. Set it to the optimal status.

English 25

Setup

Speaker Selection

The audio signals transmitted over the HDMI Cable can be changed Home Theater/TV Speaker.

• Home Theater : Video is transmitted over the HDMI connection cable only, and audio is output through the product speakers only.

• TV Speaker : Both video and audio signals are transmitted over the HDMI connection cable, and audio is output through your TV speakers only.

NOTE

`` The default setting of this function is Home Theater .

`` HDMI Audio is automatically down-mixed to 2ch for TV speakers.

`` When TV Selection is set to TV Speaker, PL II / DSP EQ/P.BASS/GIGA/S.VOL doesn't work.

`` With Speaker Selection set to 'TV Speaker', the volume can be adjusted only using the TV remote control.

User EQ

You can configure the equalizer settings manually to your preference.

Settings
		User EQ
dB
6
·
·
·
·
·
·
·
·
·
·
·
-·6
250Hz	600Hz	1kHz	3kHz	6kHz	10kHz	15kHz
		a Reset > Adjust			< Move	' Return
			mMove	" Select		' Return

Audio Return Ch.

You can enjoy TV sound from the Home Cinema speakers by using just one HDMI cable.

•Off : Turn the Audio Return Channel function off.

•Auto : Listen to TV sound from the Home Cinema speakers if your TV is compatible with the Audio Return Channel function.

NOTE

`` When Anynet+ (HDMI-CEC) is Off, the Audio Return Channel function is not available.

`` Using an ARC (Audio Return Channel)- uncertified HDMI cable may cause a problem in compatibility.

`` ARC function is only available if an ARCcompliant TV is connected.

System

Initial Settings

By using the Initial Settings, you can set the language and TV aspect .

NOTE

`` If an HDMI cable is connected to the product, the TV aspect does not appear and it is set to 16:9 Wide automatically.

DivX(R) Registration

View DivX(R) VOD Registration Code to purchase

and play DivX(R) VOD content.

NOTE

`` This option is not activated if you select OK.To activate this option, please activate the DivX(R) Deactivation.

`` Even after you reset the system, the settings of DivX Registration will not be reset.

DivX(R) Deactivation

Select this to get a new registration code.

26 English

	Change Password
Language

You can select the language you prefer for on-screen menu, disc menu, etc.

	OSD	Select the language for the on-screen
	Language	displays.
	Disc Menu	Select the language for the disc
		menu displays.
	Audio	Select the language for disc audio.
	Subtitle	Select the language for disc subtitles.

aTo select a language that does not appear in the menu, select OTHERS in the Disc Menu, Audio and Subtitle, and enter the language code of your country (see page 38).

aYou cannot select OTHERS in the OSD Language menu.

NOTE

`` The selected language will only appear if it is supported on the disc.

Security

The Parental Lock function works in conjunction with DVDs that have been assigned a rating, which helps you control the types of DVDs that your family watches. There are up to 8 rating levels on a disc.

Parental Rating

Select the rating level you want to set.

A larger number indicates that the program is intended for adult use only. For example, if you select up to Level 6, discs that contain Level 7, 8 will not play.

Enter the password and then press the ENTER button.

-The password is set to "0000" by default.

-Once the setup is complete, you will be taken to the previous screen.

Select Change and enter the 4-digit password to set the parental lock using the number buttons on the remote control.

Settings

Display	Parental Rating : Off
Audio
	Password	: Change

System

Language

Security

Support

m Move " Select ' Return

If you forgot your password

1.Remove the disc.

2.Press and hold the STOP (@) button on the remote control for 5 seconds or more. All settings will revert to the factory settings.

Support

Product Information

Provide the product information such as Model code, Softrware Version, etc.

Setup 03

English 27

Basic Functions

Disc Playback

1.Press the OPEN/CLOSE (^) button.

2.Place a disc gently into the tray with the disc's label facing up.

3.Press the OPEN/CLOSE (^) button to close the disc tray.

NOTE

`` Resume function: When you stop disc play, the product remembers where you stopped, so when you press PLAY button again, it will pick up where you left off. (This function works only with DVDs.)

Press the STOP button twice during playback to disable the Resume function.

`` If no buttons are pressed on the product or remote control for more than 3 minutes when the product is in Pause mode, it will change to STOP mode.

`` The initial screen may appear different, depending on the content of the disc.

`` Pirated discs will not play in this product because they violate the CSS(Content Scrambling System: a copy protection system) recommendations.

a will appear when an invalid button is pressed.

TV Screen Saver/Power Saving Function

•If no button input is made for more than 5 minutes in Stop or Play (music) mode, the screen saver will get activated.

•If the product is left in the screen saver mode for more than 20 minutes, the power will automatically turn off. (Except during play a music)

Audio CD(CD-DA)/MP3/WMA Playback

			BA
		Track01
		1/17
			0:15 / 3:59
Function	DVD/CD	Repeat	Play Mode

1.Insert an Audio CD(CD-DA) or an MP3 Disc into the disc tray.

•For an Audio CD, the first track will be played automatically.

-Press the [] buttons to move to the previous/next track.

•For the MP3/WMA disc, press the _+ buttons to select Music, then press the ENTER button.

-Press the $%_+ buttons to select a desired file and press the ENTER button.

-Press the () buttons to move to the previous/next pages.

2.Press the STOP (@) button to stop playback.

NOTE

`` Some MP3/WMA-CDs may not play, depending on the recording mode.

`` Table of contents of a MP3-CD varies depending on the MP3/WMA track format recorded on the disc.

`` WMA-DRM files cannot be played.

28 English

Reverse slow playback does not work.

JPEG File Playback

Images captured with a digital camera or camcorder, or JPEG files on a PC can be stored on a CD and then played back with this product.

1.Insert a JPEG disc on the disc tray.

2.Press the _+ buttons to select Photo, and then press the ENTER button.

3.Press the $% buttons to select the folder you want to play, and then press the ENTER button.

4.Press the ▲▼ buttons to select the photo you want to play, and then press the ENTER button.

•The selected file will play and slide show will start.

•To stop slide show, press the PAUSE (#) button.

•You can view the previous/next file by pressing the , buttons during the slideshow mode.

ROOT

JPEG 1

JPEG 2

JPEG 3

642 X 352 2010/01/01

Function DVD/CD Pages Return

Using the Playback Function

Forward/Reverse Search

dBAD

Press the () buttons for Search Function.

(1 (2 (3 (4 )1 )2 )3 )4

NOTE

`` No sound is played in search mode.

`` The playback search produces sound only when searching at )1 and )2 speed.

`` This function is available only for the CD-DA.

Skipping Scenes/Songs

dBAD

Press the [] buttons.

•Each time the button is pressed during playback, the previous or next chapter, track or directory (file) will be played.

•You cannot skip chapters consecutively.

Functions Basic 04

Rotate Function

G

Press the GREEN(B) or YELLOW(C) button during the PAUSE mode.

•GREEN(B) Button: Rotate 90° counterclockwise.

•YELLOW(C) Button: Rotate 90° clockwise.

NOTE

`` The maximum resolutions supported by this product are 5120 x 3480 (or 19.0 MPixel) for standard JPEG files and 2048 x 1536 (or 3.0 MPixel) for progressive image files.

Slow Motion Play

dD

Press the PAUSE (#) button and then ) button for Slow Motion play.

d *1 *2 *3

D *1 *2 *3

NOTE

`` No sound is heard during slow playback.

``

English 29

TITLE MENU

Basic Functions

Step Motion Play

dD

Press the PAUSE button repeatedly.

•The picture moves forward one frame each time the button is pressed during playback.

NOTE

`` No sound is heard during step motion playback.

5 Minute Skip function

D

During playback, press the _,+ button.

•Playback skips 5 minutes forward whenever you press the + button.

•Playback skips 5 minutes backward whenever you press the _ button.

NOTE

`` This function is available only for the DivX that contains time information.

Using the Disc Menu

d

You can view the menus for the audio language, subtitle language, profile, etc.

DISC MENU

1. During playback, press the DISC MENU button on the remote control.

2.Press the $%_+ buttons to make the desired selection, then press the ENTER button.

NOTE

`` Depending on the disc, menu setup items may vary and this menu may not be available.

Using the Title Menu

d

For DVDs containing multiple titles, you can view the title of each movie.

1.During playback, press the TITLE

MENU button on the remote control.

2.Press the $%_+ buttons to make the desired selection, then press the ENTER button.

NOTE

`` Depending on the disc, menu setup items may vary and this menu may not be available.

Repeat Playback

dBAD

DVD/DivX Repeat

You can repeat the title, chapter or the section(A-B Repeat) of the DVD/DivX.

Repeat OFF

1.	During DVD/DivX playback, press the	REPEAT
	REPEAT button on the remote control.
2.	Press the $% buttons to select a
	desired repeat mode, then press the
	ENTER button.

3.Press the ▲▼ buttons to select OFF to return to normal play, then press the ENTER button.

Z
	Title Chapter A - Off
D
	Title Folder All Off

30 English