Samsung HT-D5130 User Manual

5.1CH Blu-ray™
Home Entertainment System
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
HT-D5130_XAC_0201.indd 1HT-D5130_XAC_0201.indd 1 2011-02-09 ¿ÀÈÄ 5:03:012011-02-09 ¿ÀÈÄ 5:03:01
Safety Information
Safety Warnings
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lighting fl ash and Arrowhead within Triangle Is awarning sign alerting you of dangerous voltage Inside the product.
CAUTION :
SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
TO REDUCE THE RISK OF ELECTRIC
The explanation point within the triangle is a warning sign alerting you of important instructions accompanying the product.
WARNING
To reduce the risk of fi re or electric shock, do not
expose this appliance to rain or moisture.
CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT PRODUCTO LÁSER CLASE 1
CAUTION
Apparatus shall not be exposed to dripping or splashing and
no objects fi lled with liquids, such as vases, shall be placed on the apparatus.
DANGER
VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM. (FDA 21 CFR)
CAUTION
CLASS 1 LASER PRODUCT
This product is classifi ed as a CLASS 1 LASER
product. Use of controls, adjustments or performance of procedures other than those specifi ed herein may result in hazardous radiation exposure.
CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN. AVOID EXPOSURE TO THE BEAM (IEC 60825-1)
THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS
OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVER AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
Note to CATV system installer
This reminder is provided to call the CATV system installer’s attention to Section 820~40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
2 English
HT-D5130_XAC_0201.indd 2HT-D5130_XAC_0201.indd 2 2011-02-09 ¿ÀÈÄ 5:03:372011-02-09 ¿ÀÈÄ 5:03:37
Important Safety Instructions
Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference.
1) Read these instructions.
2) Keep these Instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifi ers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fi t into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachment/accessories specifi ed by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specifi ed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Precautions
Ensure that the AC power supply in your house
complies with the identifi cation sticker located on the back of your product.
Install your product horizontally, on a suitable base
(furniture), with enough space around it for ventilation (3~4 inches).
Do not place the product on amplifi ers or other
equipment which may become hot. Make sure the ventilation slots are not covered.
Do not stack anything on top of the product.
Before moving the product, ensure the Disc Insert
Hole is empty. In order to disconnect the product completely from
the power supply, remove the mains plug from the wall outlet, especially when left unused for a long period of time.
During thunderstorms, disconnect the AC mains
plug from the wall outlet. Voltage peaks due to lightning could damage the product.
Do not expose the product to direct sunlight or
other heat sources. This could lead to overheating and malfunction of the product.
Protect the product from moisture, and excess
heat or equipment creating strong magnetic or electric fi elds (i.e. speakers.).
Disconnect the power cable from the AC supply if
the product malfunctions. Your product is not intended for industrial use. Use
of this product is for personal use only. Condensation may occur if your product or disc
has been stored in cold temperatures. If transporting the product during the winter, wait approximately 2 hours until the product has reached room temperature before using.
The batteries used with this product contain
chemicals that are harmful to the environment. Do not dispose of batteries in the general household trash.
English 3
HT-D5130_XAC_0201.indd 3HT-D5130_XAC_0201.indd 3 2011-02-09 ¿ÀÈÄ 5:03:372011-02-09 ¿ÀÈÄ 5:03:37
Safety Information
Cautions on Handling and Storing Discs
Small scratches on the disc may reduce sound and picture quality or cause skipping.
Be especially careful not to scratch discs when handling them.
Holding discs
Do not touch the playback side of the disc.
Hold the disc by the edges so that
fi ngerprints will not get on the surface. Do not stick paper or tape on the disc.
Disc Storage
Do not keep in direct sunlight
Keep in a cool ventilated area
Keep in a clean Protection jacket.
Store vertically.
NOTE
Do not allow the discs to become contaminated with
dirt. Do not load cracked or scratched discs.
Handling and Storing Discs
If you get fingerprints or dirt on the disc, clean it with a mild detergent diluted in water and wipe with a soft cloth.
When cleaning, wipe gently from the inside to
the outside of the disc
NOTE
Condensation may form if warm air comes into
contact with cold parts inside the product. When condensation forms inside the product, it may not operate correctly. If this occurs, remove the disc and let the product stand for 1 or 2 hours with the power on.
Dolby and the double-D symbol are registered trademarks of Dolby
Laboratories. "ABOUT DIVX VIDEO: DivX® is a digital video format
created by DivX, Inc. This is an offi cial DivX Certifi ed® device that plays DivX video. Visit www.divx.com for more information and software tools to convert your fi les into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certifi ed® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod.divx.com for more information on how to complete your registration.
DivX Certifi ed® to play DivX® video up to HD 1080p, including premium content. DivX®, DivX Certifi ed® and associated logos are trademarks of DivX, Inc. and are used under license."
HDMI, the HDMI Logo, and High-Defi nition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
Oracle and Java are registered trademarks of Oracle and/or its affi liates. Other names may be trademarks of their respective owners.
This item incorporates copy protection technology that is protected by U.S. patents and other intellectual property rights of Rovi Corporation. Reverse engineering and disassembly are prohibited.
Blu-ray Disc™, Blu-ray™, and the logos are trademarks of Blu-ray Disc Association.
iPod is a trademark of Apple Inc., registered in the U.S. and other countries. iPhone is a trademark of Apple Inc.
< Open Source License Notice >
In the case of using open source software, Open Source Licenses are available on the product menu.
© 2011 Samsung Electronics Co., Ltd. All rights reserved.
License
Copyright
4 English
HT-D5130_XAC_0201.indd 4HT-D5130_XAC_0201.indd 4 2011-02-09 ¿ÀÈÄ 5:03:372011-02-09 ¿ÀÈÄ 5:03:37
Contents
SAFETY INFORMATION
2
GETTING STARTED
7
CONNECTIONS
18
SETUP
28
2 Safety Warnings 3 Important Safety Instructions 3 Precautions 4 Cautions on Handling and Storing Discs 4 License 4 Copyright
7 Key features of your new Blu-ray Home Theater 8 Icons that will be used in manual 9 Disc Types and Characteristics 13 Accessories 14 Description 14 Front Panel 15 Rear Panel 16 Remote Control
18 Connecting the Speakers 21 Connecting the Optional Wireless Receiver Module 23 Connecting the Video Out to your TV 25
Connecting Audio from External Components 26 Connecting to the Network 27 Connecting the FM Antenna
28 Initial Settings 29 Accessing the Settings Menu 30 Display 30 TV Aspect 30 Smart Hub Screen Size 30 BD Wise (Samsung Products only) 30 Resolution 32 HDMI Color Format 32 Movie Frame (24 Fs) 32 HDMI Deep Color 32 Still Mode 32 Progressive Mode 33 Audio 33 Speaker Settings 34 Musical Room Calibration 34 User EQ 35 HDMI Audio 35 Audio Return Channel 35 Digital Output 36 Dynamic Range Control 37 Audio Sync 37 Network 37 Network Settings 40 Network Status 40 BD-LIVE Internet Connection 41 System 41 Initial Settings 41 Anynet+(HDMI-CEC) 41 BD Data Management 41 Time Zone 41 DivX® Video On Demand 41 Reset 42 Language
ENGLISH
English 5
HT-D5130_XAC_0201.indd 5HT-D5130_XAC_0201.indd 5 2011-02-09 ¿ÀÈÄ 5:03:372011-02-09 ¿ÀÈÄ 5:03:37
Contents
SETUP
42
BASIC FUNCTIONS
45
NETWORK SERVICES
58
42 Security 42 BD Parental Rating 42 DVD Parental Rating 42 Change Password 42 General 42 Front Display 42 Network Remote Control 43 Support 43 Software Upgrade 44 Contact Samsung
45 Playing a Disc 45 Using the Disc menu / Title menu / Popup menu 46 Using the Search and Skip Functions 47 Slow Motion Play/Step Motion Play 47 Repeat Playback 48 Using the TOOLS button 50 Listening to Music 52 Sound Mode 53 Playing back a Picture 54 Playing back a USB Storage Device 55 Listening to Radio 55 Connecting iPod/iPhone Using the USB Cable 55 Use iPod/iPhone with a Wireless Dock Cradle (sold
separately) for iPod/iPhone 56 iPod/iPhone Models You Can Use with This Product 57 How to Link the Wireless Transmitter with the Main Unit
58 Using Smart Hub 65 Samsung Apps 67 BD-LIVE™ 67 Using the AllShare Function
OTHER INFORMATION
68 Troubleshooting 71 Index 72 Specifi cations
68
Figures and illustrations in this User Manual are provided for reference only and may differ from actual product
• appearance.
An administration fee may be charged if either
an engineer is called out at your request and there is no defect in the product
a.
(i.e. where you have failed to read this user manual) you bring the unit to a repair center and there is no defect in the product
b.
(i.e. where you have failed to read this user manual).
The amount of such administration charge will be advised to you before any work or home visit is carried out.
6 English
HT-D5130_XAC_0201.indd 6HT-D5130_XAC_0201.indd 6 2011-02-09 ¿ÀÈÄ 5:03:382011-02-09 ¿ÀÈÄ 5:03:38
01 Getting Started
P
e
e
m
Getting Started
Key features of your new Blu-ray Home Theater
Product Features
Smart Hub
You can download various chargeable or free-of charge applications through network connection. Various internet service and contents will be provided, which include news, weather forecast, stock market, games, movies and music.
AllShare
You can play videos, music and photos saved on your devices (such as your PC, mobile phones or NAS) through a network connection.
Audio Sync function
Video may lag behind the audio if the product is connected to a digital TV. To compensate for this, you can adjust the audio delay time to sync up with the video.
iPod & iPhone support
If the system is connected to iPod player using the iPod/iPhone specific USB cable or wireless transmitter (sold separately), you can play the music files in iPod/iPhone through the connected speakers.
BD Wise
BD Wise automatically adjusts BD Wise-compliant Samsung products to the optimal settings between them. This feature is enabled only if BD Wise-compliant Samsung products are connected to each other using an HDMI cable.
Virtual 7.1
Applies the 7.1 CH sound effect using the 5.1 CH speaker system.
ARC (Audio Return Channel)
You can enjoy TV sound from the Home Theater speakers by using just one HDMI cable.
English 7
HT-D5130_XAC_0201.indd 7HT-D5130_XAC_0201.indd 7 2011-02-09 ¿ÀÈÄ 5:03:382011-02-09 ¿ÀÈÄ 5:03:38
i
If b s
Getting Started
Icons that will be used in manual
Make sure to check the following terms before reading the user manual.
Term Logo Icon Definition
BD-ROM
BD-RE/-R
DVD-VIDEO
DVD-RW(V)
DVD-R
DVD+RW
DVD+R
Audio CD
MP3
WMA
JPEG
DivX MKV MP4
USB storage
device
CAUTION
NOTE
Shortcut Key
-
-
DivX
-
-
-
-
h z Z
y
o w G
x
F
This involves a function available on a BD-ROM.
This involves a function available on a BD-RE/-R disc recorded in the BD-RE format.
This involves a function available on a DVD-VIDEO.
This involves a function available on recorded DVD+RW or DVD-RW(V)/ DVD-R/+R discs that have been recorded and fi nalized.
This involves a function available on an audio CD-RW/-R (CD-DA format).
This involves a function available in a CD-RW/-R, DVD-RW/-R disc or a USB storage media containing MP3 or WMA contents.
This involves a function available in a CD-RW/-R, DVD-RW/-R disc or a USB storage media containing JPEG contents.
This involves a function available in a CD-RW/-R, DVD-RW/-R disc or a USB storage media containing DivX contents.
This involves a function available on a USB storage device.
This involves a situation where a function does not operate or settings may
!
be cancelled.
This involves tips or instructions on the page that help each function
operate.
This function provides direct and easy access pressing the button on the remote control.
This product is compatible with the NTSC color system only.
PAL discs will not play.
8 English
HT-D5130_XAC_0201.indd 8HT-D5130_XAC_0201.indd 8 2011-02-09 ¿ÀÈÄ 5:03:382011-02-09 ¿ÀÈÄ 5:03:38
01 Getting Started
Disc Types and Characteristics
Blu-ray Disc Compatibility
Blu-ray is a new and evolving format. Accordingly, disc compatibility issues are possible. Not all discs are compatible and not every disc will play back. For additional information, refer to the Disc Types and Characteristics section of this Manual.
NOTE
Playback may not work for some types of discs, or
when specifi c operations, such as angle change and aspect ratio adjustment, are being performed. Information about the discs is written in detail on the box. Please refer to this if necessary. Do not allow the disc to become dirty or scratched.
Fingerprints, dirt, dust, scratches or deposits of cigarette smoke on the recording surface may make it impossible to use the disc for playback. When a BD-Java title is played, loading may take
longer than a normal title, or some functions may perform slowly.
Discs that cannot be played
HD DVD Disc
DVD-RAM
3.9 GB DVD-R Disc for Authoring.
DVD-RW(VR mode)
Super Audio CD(except CD layer)
DVD-ROM/PD/MV-Disc, etc CVD/CD-ROM/
CDV/CD-G/CD-I/LD CDGs play audio only, not graphics.
Logos of Discs that can be played
Blu-ray Disc Dolby Digital Plus
NTSC broadcast system in
U.S.A, Canada, Korea,
Japan
DTS-HD High Resolution
Audio
DTS-HD Master Audio |
Essential
Dolby TrueHD
Java
BD-LIVE
NOTE
Some commercial discs and DVD discs purchased
outside your region may not be playable with this product. If a DVD-R/-RW disc has not been recorded properly
in DVD video format, it will not be playable.
English 9
HT-D5130_XAC_0201.indd 9HT-D5130_XAC_0201.indd 9 2011-02-09 ¿ÀÈÄ 5:03:392011-02-09 ¿ÀÈÄ 5:03:39
Getting Started
Region Code
Both the product and the discs are coded by region. These regional codes must match in order to play the disc. If the codes do not match, the disc will not play.
Disc Type
Blu-ray
DVD-VIDEO
Region
Code
North America, Central America, South America, Korea, Japan,
A
Taiwan, Hong Kong and South East Asia.
Europe, Greenland, French territories, Middle East, Africa,
B
Australia and New Zealand.
India, China, Russia, Central and
C
South Asia.
The U.S., U.S. territories and
1
Canada
Europe, Japan, the Middle East,
2
Egypt, South Africa, Greenland
Taiwan, Korea, the Philippines,
3
Indonesia, Hong Kong
Mexico, South America, Central America, Australia, New Zealand,
4
Pacifi c Islands, Caribbean
Russia, Eastern Europe, India, most of Africa, North Korea,
5
Mongolia
China
6
Area
Disc Types
BD-ROM
This Blu-ray disc can only be played back. This product can play back pre-recorded commercial BD-ROM discs.
BD-RE/-R
This Blu-ray disc can be recorded and played back. This product can play back a BD-RE/-R disc recorded by other compatible Blu-ray disc recorders.
DVD-VIDEO
This product can play back pre-recorded commercial
DVD discs (DVD-VIDEO discs) with movies. When switching from the fi rst layer to the second
layer of a dual-layered DVD-VIDEO disc, there may be momentary distortion in the image and
product
sound. This is not a malfunction of the
DVD-RW/-R/+R
This
product recorded and fi nalized with a DVD video recorder. Ability to play back may depend on recording conditions.
DVD+RW
This product can play back a DVD+RW disc recorded with a DVD Video recorder. Ability to play back may depend on recording conditions.
Audio CD (CD-DA)
This CD-RW/-R discs.
The product may not be able to play some CD­RW/-R discs due to the condition of the recording.
CD-RW/-R
Use a 700MB(80 minutes) CD-RW/-R disc. If possible, do not use a 800MB(90 minutes) or above disc, as the disc may not play back.
If the CD-RW/-R disc was not recorded as a
closed session, you may experience delays when playing back the beginning of the disc or all recorded fi les may not play.
Some CD-RW/-R discs may not be playable with this product, depending on the device which was used to burn them. For contents recorded on CD­RW/-R media from CDs for your personal use, playability may vary depending on contents and discs.
can play back a DVD-RW/-R/+R disc
product
can play back CD-DA format audio
.
10 English
HT-D5130_XAC_0201.indd 10HT-D5130_XAC_0201.indd 10 2011-02-09 ¿ÀÈÄ 5:03:402011-02-09 ¿ÀÈÄ 5:03:40
Disc Format
Using JPEG disc
CD-R/-RW, DVD-RW/-R recorded with UDF or JOLIET format can be played back.
Only JPEG fi les with the ".jpg", ".JPG", ".jpeg" or "JPEG" extension can be displayed.
Progressive JPEG is supported.
DVD-RW/-R (V)
This is a format that is used for recording data on a DVD-RW or DVD-R disc. The disc can be played by this product once it has been fi nalized.
If a disc that has been recorded in Video Mode by a different maker’s recorder but has not been fi nalized, it cannot be played by this product.
Supported File Formats
Video File Support
File Extension Container Video Codec Audio Codec Resolution
1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080
1920x1080 1920x1080 1920x1080
1920x1080
1920x1080
*.avi
*.mkv
*.asf
*.wmv
*.mp4
*.3gp
DivX 3.11/4.x/5.1/6.0
XviD
AVI
MKV
ASF
ASF Window Media Video v9
MP4
3GPP
H.264 BP/MP/HP
MPEG4 SP/ASP
Motion JPEG
DivX 3.11/4.x/5.1/6.0
XviD
H.264 BP/MP/HP
MPEG4 SP/ASP
Motion JPEG
DivX 3.11/4.x/5.1/6.0
XviD
H.264 BP/MP/HP
MPEG4 SP/ASP
Motion JPEG
H.264 BP/MP/HP
MPEG4 SP/ASP
XVID
H.264 BP/MP/HP
MPEG4 SP/ASP
MP3 AC3
LPCM
ADPCM
DTS Core
MP3 AC3
LPCM
ADPCM
DTS Core
MP3 AC3
LPCM
ADPCM
WMA
WMA 1920x1080
MP3
ADPCM
AAC
ADPCM
AAC
HE-AAC
01 Getting Started
English 11
HT-D5130_XAC_0201.indd 11HT-D5130_XAC_0201.indd 11 2011-02-09 ¿ÀÈÄ 5:03:402011-02-09 ¿ÀÈÄ 5:03:40
Getting Started
File Extension Container Video Codec Audio Codec Resolution
AC3 MPEG LPCM
AC3 MPEG LPCM
AAC
AC3
AAC
MP3 DD+
HE-AAC
*.vro
*.mpg
*.mpeg
*.ts *.tp
*.trp
VRO VOB
PS
TS
MPEG2
MPEG1
MPEG1 MPEG2
H.264
MPEG2
H.264
VC1
Restrictions
Some of the Codecs above listed are not supported if having a problem with the contents.
• Video source with incorrect container information or if corrupt will not be played properly.
• AV source with more than the standard bit rate or frame rate may not be played properly.
• If the index table is corrupt, the Seek (Jump) function will not be supported.
• If you play a video via the network, it may not be played properly depending on the network status.
Video decoder
Up to H.264 Level 4.1 supported.
• H.264 FMO/ASO/RS, VC1 SP/MP/AP L4, AVCHD not supported.
• XVID, MPEG4 SP, ASP :
- Below 1280 x 720: 60 frame max
- Above 1280 x 720: 30 frame max GMC 2 or higher not supported.
1920x1080
352x288
352x288
1920x1080
1920x1080
1920x1080 1920x1080
1920x1080
Audio decoder
Up to WMA 7,8,9 supported.
• WMA 9 PRO with more than two channels (multi-channel) not supported.
• WMA 9 Lossless, Voice not supported.
• WMA sampling rate at 22050Hz mono not supported.
Music File Support
File Extension Container Audio Codec Support Range
*.mp3
*.wma
MP3
WMA
MP3 -
Compliant with WMA version 10
WMA
* Sampling rates (in kHz) - 8, 11, 16, 22, 32,
44.1, 48
* Bit rates - All bit-rates in the range 5kbps to
384kbps
12 English
HT-D5130_XAC_0201.indd 12HT-D5130_XAC_0201.indd 12 2011-02-09 ¿ÀÈÄ 5:03:402011-02-09 ¿ÀÈÄ 5:03:40
Notes on USB connection
Supported devices:
USB storage media, MP3 player, digital camera, USB card reader
1)
Does not support if a folder or fi le name is longer than 125 characters.
2)
A subtitle fi le bigger than 300 KB may not be properly displayed.
3)
A certain USB/digital camera device may not be compatible with the product.
4)
FAT16 and FAT32 fi le systems are supported.
5)
Photo (JPEG), music (MP3) and video fi le should have their names in Korean or English. Otherwise, the fi le may not played.
Accessories
Connect directly to the product's USB port.
6) Connecting through another cable may raise problems with USB compatibility.
Inserting more than one memory device to a
7) multi-card reader may not operate properly.
PTP protocol for digital camera is not
8) supported.
Do not disconnect USB device during a
9) "loading" process.
Bigger the image resolution, the longer the
10)
delay to displaying.
DRM applied MP3 fi les downloaded from a
11)
commercial site are not played back.
01 Getting Started
Check for the supplied accessories below.
FUNCTION
POWER
TV SOURCE
RECEIVER SLEEP
BD TV
123
456
7809
REPEATFULL SCREEN
MUTE
TUNING
VOL
/CH
SFE MODE
DISC MENU MENU TITLE MENU
POPUP
TOOLS
INFO
RETURN
EXIT
TUNER MEMORY
iPod SYNC
AB
CD
DSP
SMART SEARCH
NETFLIX
HUB
MO/ST
Video Cable FM Antenna User's Manual
Remote Control/
Batteries (AAA size)
ASC Microphone
Wireless Dock Cradle for iPod/iPhone : HT-WDC10 (sold separately)
L IN
K
STANDB
Y
CHARGE
Wireless Transmitter Charging Cradle DC Power Cord DC Power Adapter
English 13
HT-D5130_XAC_0201.indd 13HT-D5130_XAC_0201.indd 13 2011-02-09 ¿ÀÈÄ 5:03:412011-02-09 ¿ÀÈÄ 5:03:41
Getting Started
Front Panel
Description
1 3 4 5 6 7
REMOTE CONTROL SENSOR
1
DISC TRAY
2 3
POWER BUTTON ( )
FUNCTION BUTTON
4
DISPLAY
5
STOP BUTTON
6
PLAY/PAUSE BUTTON
7
ENTER BUTTON
8
OPEN/CLOSE BUTTON
9
ASC IN JACK
10
VOLUME CONTROL
11
USB PORT
12
2
Detects signals from the remote control.
Opens to accept a disc.
Turns the product on and off. The mode switches as follows :
BD/DVD D. IN AUX  R. IPOD W. IPOD FM Displays the playing status, time, etc.
Stops disc playback.
Plays a disc or pauses playback.
Selects menu items or starts a Blu-ray disc. (It will not start a DVD disc.)
Opens and closes the disc tray.
Used to connect the ASC Microphone for setting up MRC (Musical Room Calibration).
Volume adjustment. You can connect a USB memory fl ash stick here and use it as storage when the product is
connected to BD-LIVE. You can also use the USB Host for software upgrades and MP3/JPEG/ DivX/MKV/MP4 playback.
8
10911
ASC IN
5V 500mA
12
NOTE
You can perform software upgrades using the USB Host jack with a USB memory fl ash stick only.
 
When the product displays the Blu-ray disc menu, you cannot start the movie by pressing the PLAY button on the product or the remote. To play the movie, you must select Play Movie or Start in the disc menu, and then press the ENTER button.
14 English
HT-D5130_XAC_0201.indd 14HT-D5130_XAC_0201.indd 14 2011-02-09 ¿ÀÈÄ 5:03:422011-02-09 ¿ÀÈÄ 5:03:42
Rear Panel
01 Getting Started
3 4
2 5 76
1
LAN
WIRELESS LAN
LAN TERMINAL
1
WIRELESS LAN JACK
2
EXTERNAL DIGITAL AUDIO IN JACK
3
(OPTICAL)
HDMI OUT JACK
4
FM ANTENNA JACK
5
TX CARD CONNECTION (WIRELESS)
6
AUX IN JACKS
7
COMPONENT VIDEO OUT JACKS
8
VIDEO OUT JACK
9
5.1 CHANNEL SPEAKER OUTPUT
10
CONNECTORS
COOLING FAN
11
DIGITAL AUDIO IN
OPTICAL
HDMI OUT
FM ANT
WIRELESS
8
COMPONENT OUT
AUX IN
VIDEO OUT
10
9
SPEAKERS OUT
CENTER SURROUNDFRONT
SUBWOOFER SURROUND
FRONT
SPEAKER IMPEDANCE : 3
11
Can be used for network based services (see pages 58~65), BD-LIVE and software upgrade under the network connection.
Can be used for network based services (see pages 58~65), BD-LIVE and software upgrade with a wireless LAN adapter.
Use this to connect external equipment capable of digital output.
Use an HDMI cable, connect this HDMI output terminal to the HDMI input terminal on your TV for the best quality picture.
Connect the FM antenna.
The TX card enables communication between the product and the optional wireless receiver module.
Connect to the 2CH analog output of an external device (such as a VCR)
Connect a TV with Component video inputs to these jacks.
Connect your TV's Video Input jack (VIDEO IN) to the VIDEO OUT Jack on this product.
Connect the front, center, surround, subwoofer speakers.
The cooling fan supplies cool air to the product to prevent overheating and always revolves when the power is on.
CAUTION
!
Ensure a minimum of 4 inches of clear space on all sides of the cooling fan when installing the product.
Do not obstruct the cooling fan or ventilation holes.
English 15
HT-D5130_XAC_0201.indd 15HT-D5130_XAC_0201.indd 15 2011-02-09 ¿ÀÈÄ 5:03:422011-02-09 ¿ÀÈÄ 5:03:42
Getting Started
Tour of the Remote Control
Remote Control
Turn the product on and off.
If you want to change to TV mode,
press the TV button.
If you want to change to Home Theater,
press the BD button.
Press numeric buttons to operate options.
Press this to see the full screen on a TV.
Press to skip backwards or forwards.
Press to stop/play a disc.
Cut off the sound temporarily.
Adjust the volume.
Press this to move to the home menu.
Press to view the disc menu.
Press this to use the Tools menu.
Select on-screen menu items and
change menu value.
Return to the previous menu.
These buttons are used both for menus
on the product and also several
Blu-ray Disc functions.
Press this to use the Netflix.
Press this to use the Smart Hub.
Select the desired Dolby Pro
Logic II audio mode.
POWER
RECEIVER SLEEP
BD TV
FUNCTION
TV SOURCE
123
456
7809
REPEATFULL SCREEN
MUTE
VOL
DISC MENU MENU TITLE MENU
TOOLS
RETURN
AB
SMART SEARCH
NETFLIX
HUB
TUNING
SFE MODE
/CH
POPUP
INFO
EXIT
TUNER
MEMORY
CD
DSP
MO/ST
This is mode selection button. or Press to select TV's video mode.
Set a Sleep time to shut off the product.
To open and close the disc tray.
Allows you to repeat a title, chapter, track or disc.
Press to search backwards or forwards.
Press to pause a disc.
Search for active FM stations and change channels.
You can set the SFE(Sound Field Effect) mode best suited for the type of music you are listening to.
Use this to enter the popup menu/title menu.
Use this to display the playback information when playing a Blu-ray/DVD disc.
Press this to exit the menu.
Used to set a preset radio frequency.
Regulate and stabilize the volume level. (Digital Signal Processor)
Press this to search a contents. Select MONO or STEREO for radio
broadcasting.
16 English
HT-D5130_XAC_0201.indd 16HT-D5130_XAC_0201.indd 16 2011-02-09 ¿ÀÈÄ 5:03:432011-02-09 ¿ÀÈÄ 5:03:43
01 Getting Started
Installing batteries in the Remote Control
* Battery size: AAA
NOTE
Make sure to match the “+” and “–” ends of
the batteries with the diagram inside the compartment.
Assuming typical TV usage, the batteries last for about one year. The remote control can be used up to
approximately 23 feet (7 meters) in a straight line.
Setting the Remote Control
You can control certain functions of your TV with this remote control.
When operating a TV with the remote control
Press the TV button to set the remote control
1.
to TV mode.
2.
Press the POWER button to turn on the TV.
3.
While holding down the POWER button, enter the code corresponding to your brand of TV.
If there is more than one code listed for your TV in the table, enter one at a time to determine which code works.
Example : For a Samsung TV
While holding down the POWER button, use the number buttons to enter 00, 15, 16, 17 and 40.
If the TV turns off, the setting is complete.
4.
You can use the TV POWER, VOLUME,
CHANNEL, and Numeric buttons (0~9).
NOTE
The remote control may not work on some
brands of TV's. Also, some operations may not be possible, depending on your brand of TV.
The remote control will work with Samsung TVs by default.
TV Brand Code List
Brand Code
Admiral
(M.Wards)
A Mark
Anam
AOC
Bell &
Howell
(M.Wards)
Brocsonic
Candle
Cetronic
Citizen
Cinema
Classic
Concerto
Contec
Coronado
Craig
Croslex
Crown
Curtis
Mates
CXC
Daewoo
Daytron Dynasty
Emerson
Fisher
Funai
Futuretech
General
Electric (GE)
Hall Mark
Hitachi
Inkel
JC Penny
JVC KTV KEC
KMC
LG
(Goldstar)
Luxman
LXI
(Sears)
Magnavox
Marantz
Matsui
MGA
56, 57, 58
01, 15
01, 02, 03, 04, 05, 06, 07, 08, 09, 10,
11, 12, 13, 14
01, 18, 40, 48
57, 58, 81
59, 60
18 03
03, 18, 25
97 03 18 46 15
03, 05, 61, 82, 83, 84
62 03
59, 61, 63
03
02, 03, 04, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 32,
34, 35, 36, 48, 59, 90
40 03
03, 15, 40, 46, 59, 61,
64, 82, 83, 84, 85
19, 65
03 03
06, 40, 56, 59,
66, 67, 68
40
15, 18, 50, 59, 69
45
56, 59, 67, 86
70
59, 61, 87, 88
03, 15, 40
15
01, 15, 16, 17, 37, 38, 39, 40, 41, 42, 43, 44
18
19, 54, 56, 59,
60, 62, 63, 65, 71
15, 17, 18, 48, 54,
59, 60, 62, 72, 89
40, 54
54
18, 40
Brand Code
Mitsubishi/
MGA MTC NEC Nikei
Onking
Onwa
Panasonic
Penney
Philco
Philips
Pioneer
Portland
Proton
Quasar
Radio
Shack
RCA/
Proscan Realistic
Sampo
Samsung
Sanyo
Scott Sears Sharp
Signature
2000
(M.Wards)
Sony Soundesign Spectricon
SSS
Sylvania
Symphonic
Tatung
Techwood
Teknika
TMK
Toshiba
Vidtech
Videch
Wards
Yamaha
York
Yupiteru
Zenith Zonda
Dongyang
18, 40, 59, 60, 75
18, 19, 20, 40, 59, 60
06, 07, 08, 09, 54,
66, 67, 73, 74
03, 15, 17, 18, 48, 54, 59, 62, 69, 90
15, 17, 18, 40,
48, 54, 62, 72 63, 66, 80, 91
15, 18, 59
06, 66, 67
17, 48, 56, 60,
61, 75
18, 59, 67, 76, 77,
78, 92, 93, 94
03, 19
00, 15, 16, 17, 40, 43, 46, 47, 48, 49,
59, 60, 98
19, 61, 65
03, 40, 60, 61
15, 18, 19 15, 57, 64
57, 58
50, 51, 52, 53, 55
03, 40
18, 40, 48, 54,
59, 60, 62 61, 95, 96
03, 15, 18, 25
18, 40
19, 57, 63, 71
59, 60, 69
15, 17, 18, 40,
48, 54, 60, 64
58, 79
03, 54
18
03 03 03
18
40
40
01 18
06 18
18
18 40 03
01
English 17
HT-D5130_XAC_0201.indd 17HT-D5130_XAC_0201.indd 17 2011-02-09 ¿ÀÈÄ 5:03:432011-02-09 ¿ÀÈÄ 5:03:43
Connections
This section involves various methods of connecting the product to other external components. Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
Connecting the Speakers
SW
Position of the product
Place it on a stand or cabinet shelf, or under the TV stand.
Selecting the Listening Position
The listening position should be located about 2.5 to 3 times the distance of the TV's screen size away from the TV. Example : For 32" TV's 6.56 ~ 7.87 feet(2~2.4m)
For 55" TV's 11.5 ~ 13.1 feet(3.5~4m)
Place these speakers in front of your listening position, facing inwards (about 45°)
Front Speakers
Center Speaker
Surround Speakershj
Subwoofer
ei
f
g
toward you. Place the speakers so that their tweeters will be at the same height as your ear. Align the front face of the front speakers with the front face of the center speaker or place them slightly in front of the center speakers.
It is best to install it at the same height as the front speakers. You can also install it directly over or under the TV.
Place these speakers to the side of your listening position. If there isn't enough room, place these speakers so they face each other. Place them about 2 to 3 feet (60 to 90cm) above your ear, facing slightly downward.
Unlike the front and center speakers, the surround speakers are used to
*
handle mainly sound effects and sound will not come from them all the time.
The position of the subwoofer is not so critical. Place it anywhere you like.
18 English
HT-D5130_XAC_0201.indd 18HT-D5130_XAC_0201.indd 18 2011-02-09 ¿ÀÈÄ 5:03:442011-02-09 ¿ÀÈÄ 5:03:44
CAUTION
!
Do not let children play with or near the speakers. They could get hurt if a speaker falls.
When connecting the speaker wires to the speakers, make sure that the polarity (+/ –) is correct.
Keep the subwoofer speaker out of reach of children so as to prevent children from inserting their hands or alien substances
into the duct (hole) of the subwoofer speaker. Do not hang the subwoofer on the wall through the duct (hole).
NOTE
If you place a speaker near your TV set, screen color may be distorted because of the magnetic fi eld generated by the
speaker. If this occurs, place the speaker away from your TV set.
Speaker Components Assembled Speakers
(L) (R)
SCREW (5X15): 2EA
02 Connections
SCREW (4X20): 8EA
FRONT
NOTE
Refer to page 20 to install the Speakers on the Tallboy Stand.
STAND
(L) (R)
SURROUND
STAND BASE SUBWOOFER
CENTER
SPEAKER CABLE
¨
FRONT SPEAKER
SURROUND SPEAKER
CENTER SPEAKER
SUBWOOFER
English 19
HT-D5130_XAC_0201.indd 19HT-D5130_XAC_0201.indd 19 2011-02-09 ¿ÀÈÄ 5:03:442011-02-09 ¿ÀÈÄ 5:03:44
Connections
SPEAKERS OUT
SPEAKER IMPEDANCE : 3
NENT OUT
VIDEO OUT
SUBWOOFER SURROUND
CENTER SURROUNDFRONT
FRONT
OUT
VIDEO OUT
SPEAKERS OUT
SPEAKER IMPEDANCE : 3
SUBWOOFER SURROUND
CENTER SURROUNDFRONT
FRONT
Installing the Speakers on the Tallboy Stand
Turn the Stand Base upside-down and connect it
1.
to the Stand. Insert small screws (4x20, For connecting Stand &
2.
Stand Base) clockwise into the four holes marked using a screwdriver as shown in the illustration.
!
CAUTION
When you use a torque screwdriver, be careful not
to put excessive force. Otherwise, it runs idle or can be damaged. (torque screwdriver- below 15 kg.f.cm)
3.
Connect the upper Speaker to the assembled Stand.
4.
Insert another large screw (5x15, For connecting Speaker & Stand) clockwise into the hole on the rear of the speaker using a screwdriver.
5.
This is the appearance after the speaker is installed. Follow this steps to install other speaker.
Connecting The Speakers
1
3
5
Stand Base
Stand
Stand
Speaker
2
4
Press down the terminal tab on the back of the speaker.
1.
Insert the black wire into the black terminal (–) and the red wire into the
2.
red terminal (+), and then release the tab.
3.
Connect the connecting plugs to the back of the product by matching the colors of the speaker plugs to the speaker jacks.
Black
Red
Surround Speaker (L)
Front Speaker (L)
Front Speaker (R)
Center Speaker
Subwoofer
Surround Speaker (R)
20 English
HT-D5130_XAC_0201.indd 20HT-D5130_XAC_0201.indd 20 2011-02-09 ¿ÀÈÄ 5:03:532011-02-09 ¿ÀÈÄ 5:03:53
Connecting the Optional Wireless Receiver Module
SPEAKERS OUT
SPEAKER IMPEDANCE : 3
COMPONENT OUT
VIDEO OUT
AUX IN
SUBWOOFER SURROUND
CENTER SURROUNDFRONT
FRONT
COMPONENT OUT
VIDEO OUT
AUX IN
SPEAKERS OUT
SPEAKER IMPEDANCE : 3
SUBWOOFER SURROUND
CENTER SURROUNDFRONT
FRONT
O
COMPO
O
AUX IN
To connect the surround speakers wirelessly, you have to purchase the wireless receiver module and TX card from your Samsung retailer.
This product should be connected with the SWA-5000 only.
02 Connections
Center Speaker
Subwoofer
Surround Speaker (L)
Surround Speaker (R)
Wireless Receiver Module
Wireless Receiver Module (SWA-5000)
1.
Press down the terminal tab on the back of the speaker.
2.
Insert the black wire into the black terminal (–) and the red wire into the red terminal (+), and then release the tab.
3.
Connect the connecting plugs to the back of the product by matching the colors of the speaker plugs to the speaker jacks.
4.
With the product turned off, insert the TX card into the TX Card Connection (WIRELESS) on the back of the product.
Hold the TX card so that the label "WIRELESS" faces upward and insert the card into the port.
The TX card enables communication between the product and the wireless receiver module.
5.
Connect the left and right surround speakers to the wireless Receiver module.
6.
Plug the power cord of the wireless Receiver module in the wall outlet .
Front Speaker (R)
Black
FM ANT
WIRELESS
Front Speaker (L)
Red
COMPONENT OUT
NENT OUT
AUX IN
TX Card
VIDE
VIDE
English 21
HT-D5130_XAC_0201.indd 21HT-D5130_XAC_0201.indd 21 2011-02-09 ¿ÀÈÄ 5:03:572011-02-09 ¿ÀÈÄ 5:03:57
Connections
!
CAUTION
Do not insert any other card except the TX card dedicated to the product. If a different TX card is used, the product may be damaged or the card may not be removed easily.
Do not insert the TX card upside down or in the reverse direction.
Insert the TX card when the product is turned off. Inserting the card when it is turned on may cause a problem.
If the TX Card is inserted and wireless receiver module setting is complete, sound is not output from the Surround Speaker connectors on the product.
The wireless receiving antenna is built into the wireless receiver module. Keep it away from water and moisture.
For optimal listening performance, make sure that the area around the wireless receiver module location is clear of any obstructions.
If no sound is heard from the wireless surround speakers, switch the mode to Dolby Pro Logic II.
In 2-CH mode, no sound will be heard from the wireless surround speakers.
NOTE
Place the wireless receiver module at the rear of the listening position. If the wireless receiver module is
too close to the product, some sound interruption may be heard due to interference.
If you use a device such as a microwave oven, wireless LAN Card or any other device that uses the same frequency (2.4/5.8GHz) near the product, some sound interruption may be heard due to interference.
The transmission distance from the product to the wireless receiver module is about 33 feet (10m), but may vary depending on your operating environment. If a steel-concrete wall or metallic wall is between the product and the wireless receiver module, the system may not operate at all, because the radio wave cannot penetrate metal.
If the product doesn't make wireless connection, the system needs ID Setting between the product and wireless receiver module. With the product turned off, press the remote control's number buttons "0"J"1"J"3"J"5". With the wireless receiver module turned on, press "ID SET" button on the back of the wireless receiver module for 5 seconds. And then power on the product (HT-D5130).
22 English
HT-D5130_XAC_0201.indd 22HT-D5130_XAC_0201.indd 22 2011-02-09 ¿ÀÈÄ 5:03:592011-02-09 ¿ÀÈÄ 5:03:59
Connecting the Video Out to your TV
S
D
A
Choose one of the three methods for connecting to a TV.
02 Connections
METHOD 1
LAN
WIRELESS LAN
IGITAL
DIGITAL
UDIO IN
AUDIO IN OPTICAL
HDMI OUT
FM ANT
WIRELESSWIRELES
HDMI OUT
HDMI IN
METHOD 1 : HDMI
Connect an HDMI cable (not supplied) from the HDMI OUT jack on the back of the product to the HDMI IN jack on your TV.
NOTE
Certain HDMI output resolutions may not work, depending on your TV.
 
If an HDMI cable is connected or removed during playback of a CD-DA, MP3 or JPEG fi le, the product will stop playing.
After making the video connection, set the Video input source on your TV to match the corresponding Video output (HDMI, Component or Composite) on your product. See your TV owner's manual for more information on how to select the TV's Video Input source.
If you have set the product's remote control to operate your TV, press the TV SOURCE button on the remote control and select HDMI as the external source of the TV.
HDMI Auto Detection Function
Using an HDMI cable, connect the HDMI OUT terminal on the rear of the product to the HDMI IN
1.
terminal of your TV.
2.
Turn on the product and TV.
For possible HDMI resolutions, see page 31.
This function is not available if the HDMI cable does not support CEC.
HDMI is an interface that enables the digital transmission of video and audio data with just a single connector.
Using HDMI, the product transmits a digital video and audio signal and displays a vivid picture on a TV having an HDMI input jack.
HDMI connection description
- HDMI outputs only a pure digital signal to the TV.
- If your TV does not support HDCP, random noise appears on the screen.
What is the HDCP?
HDCP (High-band width Digital Content Protection) is a system for protecting BD/DVD content outputted via HDMI from being copied. It provides a secure digital link between a video source (PC, DVD. etc) and a display device (TV, projector. etc). Content is encrypted at the source device to prevent unauthorized copies from being made.
(BEST QUALITY)
English 23
HT-D5130_XAC_0201.indd 23HT-D5130_XAC_0201.indd 23 2011-02-09 ¿ÀÈÄ 5:03:592011-02-09 ¿ÀÈÄ 5:03:59
Connections
S
T
S
3
AUX IN
Green
Blue
Red
METHOD 2
COMPONENT OUT
AUX IN
VIDEO OUT
Yellow
SPEAKERS OUT
PEAKERS OU
CENTER SURROUNDFRONT
SUBWOOFER SURROUND
FRONT
SPEAKER IMPEDANCE : 3
PEAKER IMPEDANCE :
METHOD 3
METHOD 2 : Component Video (BETTER QUALITY)
If your television is equipped with Component Video inputs, connect a Component video cable (not supplied) from the Component Video Output (Pr, Pb and Y) Jacks on the back of the product to the Component Video Input Jacks on your TV.
NOTE
You can select from a variety of resolution settings such as 1080i, 720p, 480p and 480i, depending on the
disc type. (See page 31)
The actual resolution may differ from the setting in the Setup menu if both Component and HDMI cables are connected. The resolution may also be different depending on the disc. (See page 31)
After making the video connection, set the Video input source on your TV to match the corresponding Video output (HDMI, Component or Composite) on your product. See your TV owner's manual for more information on how to select the TV's Video Input source.
If you have set the product's remote control to operate your TV, press the TV SOURCE button on the remote control and select COMPONENT as the external source of the TV.
In DVD playback, if both HDMI and Component jacks are connected and you select the Component 1080p, 1080i, 720p or 480p mode, the Display Setup menu will show the output resolution as 1080p, 1080i, 720p or 480p in the menu. The resolution is actually 480i.
METHOD 3 : Composite Video
(GOOD QUALITY)
Connect the supplied Video cable from the VIDEO OUT jack on the back of the product to the VIDEO IN jack on your TV.
NOTE
The VIDEO source is always output in 480i resolution regardless of the resolution set in the Setup
menu. (See page 31)
After making the video connection, set the Video input source on your TV to match the corresponding Video output (HDMI, Component or Composite) on your product. See your TV owner's manual for more information on how to select the TV's Video Input source. If you have set the product's remote control to operate your TV, press the
the remote control and select VIDEO as the external source of the TV.
CAUTION
!
Do not connect the unit through a VCR. Video signals fed through VCRs may be affected by
copyright protection systems and the picture will be distorted on the television.
TV SOURCE
button on
24 English
HT-D5130_XAC_0201.indd 24HT-D5130_XAC_0201.indd 24 2011-02-09 ¿ÀÈÄ 5:04:002011-02-09 ¿ÀÈÄ 5:04:00
Connecting Audio from External Components
This system supports Digital sampling frequencies of 32 kHz of higher from external digital components.
T
T
W
S
V
T
FM ANT
COMPONENT OUT
COMPONENT OU
02 Connections
DIGITAL
AUDIO IN OPTICAL
HDMI OUT
HDMI OU
Optical Cable
WIRELESS
IRELES
Red
AUX IN
VIDEO OUT
IDEO OU
White
(not supplied)
Audio Cable
(not supplied)
If the external analog
component has only one
Set-Top Box
OPTICAL
Audio Out, connect either
left or right.
VCR
AUX
OPTICAL : Connecting an External Digital Component
Digital signal components such as a Cable Box/Satellite receiver (Set-Top Box).
Connect the Digital Input (OPTICAL) on the product to the Digital Output of the external digital
1.
component. Press the FUNCTION button to select D.IN input.
2.
The mode switches as follows : BD/DVD D. IN AUX R. IPOD W. IPOD FM
NOTE
To see video from your Cable Box/Satellite receiver, you must connect it's video output to a TV.
This system supports Digital sampling frequencies of 32 kHz of higher from external digital components.
This system supports only DTS and Dolby Digital audio, MPEG audio which is bitstream cannot be supported.
AUX : Connecting an External Analog Component
Analog signal components such as a VCR.
Connect AUX IN (Audio) on the product to the Audio Out of the external analog component.
1.
Be sure to match connector colors.
Press the FUNCTION button to select AUX input.
2.
The mode switches as follows :
NOTE
You can connect the Video Output jack of your VCR to the TV, and connect the Audio Output jacks of
the VCR to this product.
HT-D5130_XAC_0201.indd 25HT-D5130_XAC_0201.indd 25 2011-02-09 ¿ÀÈÄ 5:04:012011-02-09 ¿ÀÈÄ 5:04:01
BD/DVD D. IN AUX  R. IPOD W. IPOD FM
English 25
Connections
T
D
A
N
Connecting to the Network
This product enables you to view network based services (See pages 58~65) such as Internet@TV and BD-LIVE, as well as receive software upgrades when a network connection is made. We recommend using an Wireless router or IP router for the connection. For more information on router connection, refer to the user manual of the router or contact the router manufacturer for technical assistance.
Cable Network
Using the Direct LAN Cable (UTP cable), connect the LAN terminal of the product to the LAN
1. terminal of your modem.
Set the network options. (See page 37)
2.
LAN
WIRELESS LAN
Router
Broadband modem
(with integrated router)
Broadband
service
NOTE
Internet access to Samsung’s software update server may not be allowed, depending on the router you use or the
Or
Networking with PC for
AllShare function
(See page 67)
IGITAL
DIGITAL
AUDIO IN
UDIO I
OPTICAL
Broadband modem
HDMI OUT
HDMI OU
Broadband
service
ISP’s policy. For more information, contact your ISP (Internet Service Provider). For DSL users, please use a router to make a network connection.
For the AllShare function, a PC must be connected in the network as shown in the fi gure.
26 English
HT-D5130_XAC_0201.indd 26HT-D5130_XAC_0201.indd 26 2011-02-09 ¿ÀÈÄ 5:04:022011-02-09 ¿ÀÈÄ 5:04:02
Wireless Network
SS
H
H
A
You can connect to the network with a Wireless IP sharer.
A wireless AP/IP router is required to make a wireless network connection. Connect the wireless
1.
LAN adapter to the Wireless LAN Adapter on the rear panel of the product. Set the network options. (See page 37)
2.
Broadband
service
LAN
DIGITAL
DIGITAL
AUDIO IN
UDIO IN
OPTICAL
02 Connections
Wireless IP sharer
WIRELESS LAN
PC
Wireless LAN Adapter (not supplied)
Networking with PC for AllShare function
(See page 67)
NOTE
This product is compatible with only Samsung's Wireless LAN Adapter. (not supplied) (Model name: WIS09ABGN).
- The Samsung Wireless LAN Adapter is sold separately. Contact a Samsung Electronics retailer for purchasing. You must use a wireless IP sharer that supports IEEE 802.11 a/b/g/n. (n is recommended for stable operation of the
wireless network.) Wireless LAN, by its nature, may cause interference, depending on the use condition (AP performance, distance, obstacles,
interference by other radio devices, etc). Set the wireless IP sharer to Infrastructure mode. Ad-hoc mode is not supported.
When applying the security key for the AP (wireless IP sharer), only the following is supported.
Authentication Mode : WEP, WPAPSK, WPA2PSK
1) Encryption Type : WEP, AES
2)
For the AllShare function, a PC must be connected in the network as shown in the fi gure.
Connecting the FM Antenna
Connect the FM antenna supplied to the FM
FM Antenna (supplied)
1.
ANTENNA Jack. Slowly move the antenna wire around until you
2.
fi nd a location where reception is good, then
FM ANT
fasten it to a wall or other rigid surface.
NOTE
This product does not receive AM broadcasts.
WIRELESSWIRELE
English 27
HT-D5130_XAC_0201.indd 27HT-D5130_XAC_0201.indd 27 2011-02-09 ¿ÀÈÄ 5:04:042011-02-09 ¿ÀÈÄ 5:04:04
Setup
Initial Settings
Turn on your TV after connecting the product.
1.
When you connect and turn on the product to a TV for the fi rst time, the Initial Settings screen appears.
Initial Settings | On-Screen Language
Select a language for the on-screen displays.
Български Hrvatski Čeština Dansk Nederlands English Eesti Suomi Français Deutsch Indonesia Italiano
2.
Press the ▲▼◄► buttons to select the desired language, and then press the ENTER button.
3.
Press the ENTER button to select Start.
4.
Press the ▲▼ buttons to select the desired TV Aspect Ratio, and then press the ENTER button. (See page 30) Musical Room Calibration screen will be displayed.
5.
Plug the ASC microphone into the ASC IN jack on the product. (See page 34)
6.
Press the ENTER button to select Start button. Setting the Musical Room Calibration function takes about 3 minutes.
7.
Press the ▲▼ buttons to select the desired Network Settings : Wired, Wireless
(General), WPS(PBC) or One Foot Connection, and then press the ENTER
button. If you do not know the details of your Network Settings, press the BLUE (D) button on your remote instead to skip Network Settings here, fi nish the Initial Settings, and go to the Home menu. If you selected a Network Settings, go to pages 37~40 for more information about the Network settings. When done, go to Step 8.
8.
The Home menu appears. (For more information about the Home menu, please see page 29.)
Ελληνικά Magyar
한국어
m
Move " Enter
Home Menu
My Contents
Videos
Photos
Music
My Devices Internet Settings
Function
d PBC(WPS)
NOTE
The Home menu will not appear if you do not
confi gure the initial settings except as noted below.
If you press the BLUE (D) button during the Musical Room Calibration/network setup, you can access the Home menu even if the network setup is not completed yet.
If you want to display the Initial Setting screen again to make changes, select the Reset option. (See page 41)
If you use an HDMI cable to connect the product to an Anynet+(HDMI-CEC)­compliant Samsung TV and 1.) You have set the Anynet+(HDMI-CEC) feature to On in both the TV and the product and 2.) You have set the TV to a language supported by the product, the product will select that language as the preferred language automatically.
If you leave the product in the stop mode for
more than 5 minutes without using it, a screen saver will appear on your TV. If the product is left in the screen saver mode for more than 20 minutes, the power will automatically turn off.
28 English
HT-D5130_XAC_0201.indd 28HT-D5130_XAC_0201.indd 28 2011-02-09 ¿ÀÈÄ 5:04:062011-02-09 ¿ÀÈÄ 5:04:06
Accessing the Settings Menu
U
T
U
T
S
O
POPU
DISC MENU MENU TITLE MENU
1
DISC MEN
TOOLS
OOL
ITLE MEN
POPUP
P
INFO
INF
3
2
1
2
3
4
RETURN
MENU Button : Press to move to the Home menu.
RETURN Button : Return to the previous menu.
ENTER / DIRECTION Button :
Move the cursor or select an item. Activate the currently selected item. Confi rm a setting.
EXIT Button : Press to exit the current menu.
To access the Settings menu and sub-menus, follow these steps:
1.
Press the POWER button. The Home Menu appears.
Home Menu
EXIT
4
Press the ◄► buttons to select Settings,
2.
and then press the ENTER button. Press the ▲▼ buttons to select the desired
3.
submenu, and then press the ENTER button.
Press the ▲▼ buttons to select the desired
4.
item, and then press the ENTER button. Press the EXIT button to exit the menu.
5.
NOTE
When the product is connected to a network,
select Internet from the Home menu. Download the desired content from Samsung Apps. (See pages 65~67)
The access steps may differ depending on the menu you selected.
The OSD (On Screen Display) may change in
this product after you upgrade the software version.
03 Setup
My Contents
Videos
1
Function
My Devices Internet Settings
2
Selects My Devices.
1
Selects Function.
2
Selects My Contents.
3
Selects Internet.
4
Selects Settings.
5
Displays the buttons available.
6
Photos
Music
d
PBC(WPS)
3 4
5
6
English 29
HT-D5130_XAC_0201.indd 29HT-D5130_XAC_0201.indd 29 2011-02-09 ¿ÀÈÄ 5:04:082011-02-09 ¿ÀÈÄ 5:04:08
Setup
Display
You can confi gure various display options such as the TV Aspect Ratio, Resolution, etc.
TV Aspect
Depending on the type of television you have, you may want to adjust the screen size setting.
16:9 Original : Select when you connect the
product to a 16:9 TV screen. The product will display all content in its original aspect ratio. Content formatted in 4:3 will be displayed with black bars on the left and right.
16:9 Full : Select when you connect the product
to a 16:9 TV screen. All content will fi ll the full screen. Content formatted in 4:3 will be stretched.
4:3 Letter Box : Select when you connect the
product to a 4:3 TV screen. The product will display all content in its original aspect ratio. Content formatted in 16:9 will be displayed with black bars on the top and bottom.
4:3 Pan-Scan : Select when you connect the
product to a 4:3 TV screen. 16:9 content will have the extreme left and right portions cut off.
NOTE
Depending on the disc type, some aspect ratios
may not be available.
If you select an aspect ratio and option which is different than the aspect ratio of your TV screen, then the picture might appear to be distorted.
If you select the 16:9 Original, your TV may display 4:3 Pillarbox (black bars on sides of picture).
Smart Hub Screen Size
Set the Smart Hub Screen to the optimal size.
Size 1 : Smart Hub screen size will be smaller than
default. You may see some black on sides of screen.
Size 2 : This is the default setting for Smart Hub.
The product displays the normal Smart Hub screen size.
Size 3 : This will display a larger Smart Hub screen
size. The image may be too large for your TV screen.
BD Wise (Samsung Products only)
BD Wise is Samsung’s latest inter-connectivity feature.
When you connect a Samsung product and a Samsung TV with BD Wise to each other via HDMI, and BD Wise is on in both the product and TV, the product outputs video at the video resolution and frame rate of the BD/DVD disc.
Off : The output resolution stays fi xed at the
resolution you set previously in the Resolution menu, regardless of the resolution of the disc. See Resolution below.
On : The product outputs video at the original
resolution and frame rate of the BD/DVD disc.
NOTE
When BD Wise is on, the Resolution setting
automatically defaults to BD Wise and BD Wise appears in the Resolution menu. If the product is connected to a device that
does not support BD Wise, you can not use the BD Wise function.
For proper operation of BD Wise, set the BD
Wise menu of both the product and the TV to On.
Resolution
Lets you set the output resolution of the Component and HDMI video signal to Auto, 1080p, 1080i, 720p, 480p, or 480i. The number indicates the number of lines of video per frame. The i and p indicate interlaced and progressive scan, respectively. The more lines, the higher the quality.
Auto : Automatically sets the output resolution to
the connected TV’s maximum resolution. BD Wise :
resolution of the BD/DVD disc if you have connected the product via HDMI to a TV with the BD Wise feature. (The BD Wise menu item appears only if BD Wise is set to On. See BD Wise above.)
1080p : Outputs 1080 lines of progressive
1080i : Outputs 1080 lines of interlaced video.
720p : Outputs 720 lines of progressive video.
480p : Outputs 480 lines of progressive video.
480i : Outputs 480lines of interlaced video.
Automatically sets the resolution to the
video. (HDMI only)
(VIDEO only)
30 English
HT-D5130_XAC_0201.indd 30HT-D5130_XAC_0201.indd 30 2011-02-09 ¿ÀÈÄ 5:04:102011-02-09 ¿ÀÈÄ 5:04:10
Loading...
+ 122 hidden pages