Samsung HLT5089SAX/XAA User Manual
Register your product at www.samsung.com/global/register
Record your Model and Serial number here for future reference.
▪ Model _______________ ▪ Serial No. _______________
Owner’s Instructions
HL-T5089S
HL-T5689S
HL-T6189S
DLP TV
A Guide to Digital TV
● What is Digital Television?
Digital television (DTV) is a new way of transmitting high quality video and audio to your TV set. Using DTV, broadcasters can
transmit high definition TV (HDTV) images, Dolby digital surround audio, and new services such as multicasting (transmitting
more than one program on the same TV channel) and datacasting. Several of these services can be combined into a single digital
broadcast.
Digital Television Services
● Digital Picture Quality
DTV programs are transmitted in two different formats. The first is Standard Definition Television (SDTV) and the second is High
Definition Television (HDTV).
SDTV program formats include 480-line interlaced (480i) and 480-line progressive (480p) video. 480i programs are essentially
●
a digital version of our current analog TV programs, while the 480p format offers improved image detail over 480i. Some 480p
programs are broadcast in widescreen and are comparable to progressive-scan DVD movies in image quality.
HDTV program formats include 1080-line interlaced (1080i) and 720-line progressive (720p). Both HDTV formats are always
●
broadcast in widescreen, and offer much higher picture quality than SDTV.
Dolby Surround Sound
●
With DTV, you can listen to a variety of Dolby digital audio formats from Dolby Surround 2.0 to Dolby Digital 5.1 surround, using
your home audio system. Many HDTV programs are now broadcast with DD 5.1 soundtracks.
FCC Statements
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
To comply with the FCC RF exposure compliance requirements, this device and its antenna must not be co-located or operated in
conjunction with any other antenna or transmitter.
© 2007 Samsung Electronics Co., Ltd. All rights reserved.
English - 2
English - 3
Q&A
1. Is the antenna I use for existing TV reception good enough for DTV?
Over-the-air (OTA) digital TV broadcasting uses the same channels as analog TV and works well with many existing TV antennas.
However, DTV broadcast channel assignments are different than analog channels. You should find out whether your local DTV
broadcasts are on VHF (channels 2-13) or UHF (channels 14-69) to see if you need a different antenna.
If your DTV channels are on UHF and you already get good UHF reception, your present antenna may work fine. The same holds
true for VHF DTV reception. Note that in some markets, both VHF and UHF channels are used for DTV broadcasts.
You can find out the latest DTV channel assignments for your area by browsing selected Internet web sites such as www.titantv.
com, www.10000watts.com, and www.fcc.gov.
2. How difficult is it to receive DTV signals indoors?
This depends on whether your local DTV stations are running full power or not and how close your location is to the transmission
tower. DTV receivers do not require as much signal as analog TV receivers to produce high-quality images and sound.
Once the DTV signal level exceeds a certain threshold at the receiver, the digital video and audio data is decoded at the same
quality it was originally encoded for broadcast.
This is a big advantage for DTV over analog TV - there is no noise, ghosting, static, or scratchy audio.
3. How can I connect an antenna in my townhouse, co-operative apartment, condominium, or
apartment?
The Federal Communications Commission’s OTARD Rule (part of the Telecommunications Act of 1996) allows residents of
condominiums, townhouse, or members of neighborhood associations to put up outside antennas for reception of broadcast TV
signals as long as those antennas are not located in common areas and are no more than 12’ in height.
Residents of rental units (apartments, etc.) are not covered by the OTARD rules and will have to use indoor antennas to receive
DTV broadcasts. It is possible that the landlord of an apartment complex can provide broadcast DTV signals via a master TV
antenna system to each apartment.
4. Can I connect my DTV set-top receiver to my cable TV service?
Cable TV systems use a different method for transmitting digital TV programs that is currently incompatible with broadcast DTV set-
top receivers. So you will still need to use an outdoor or indoor antenna to receive OTA broadcast DTV programs.
The good news is that you won’t have to pay a monthly or per-program charge to watch OTA DTV and HDTV programs. They’re
free, unlike subscription satellite TV or premium cable TV. All you need is an antenna and a DTV set-top receiver to enjoy clear,
sharp widescreen images and high-quality audio.
Contents
General Information
■
Viewing Position .......................................................5
■
List of Features .........................................................5
■
Checking Parts .........................................................6
■
Viewing the Control Panel ........................................6
■
Viewing the Connection Panel .................................8
■
Remote Control ........................................................9
■
Installing Batteries in the Remote Control ..............10
Connections
■
Connecting VHF and UHF Antennas ......................10
■
Connecting Cable TV ............................................. 11
■
Connecting a VCR ..................................................12
■
Connecting a Camcorder .......................................13
■
Connecting a DVD Player/Set-Top Box .................. 13
■
Connecting a DVD Player/Set-Top Box via HDMI ..14
■
Connecting a DVD Player/Set-Top Box via DVI .....14
■
Connecting a Digital Audio System ........................15
■
Connecting an Amplifier/DVD Home Theater .........15
■
Connecting a PC ....................................................16
Operation
■
Turning the TV On and Off .....................................16
■
Plug & Play Feature ...............................................17
■
Changing Channels ................................................ 19
■
Adjusting the Volume ..............................................19
■
Viewing the Display ................................................20
■
Viewing the Menus .................................................20
■
Using the TOOLS Button ........................................20
■
Memorizing the Channels .......................................21
■
Setting Up Your Remote Control ............................22
■
To Select the Source ..............................................27
■
To Edit the Input Source Name ..............................27
Picture Control
■
Using Automatic Picture Settings ...........................28
■
Making Detail Settings on the Picture ....................29
■
Changing the Screen Size ......................................30
■
Digital Noise Reduction ..........................................31
■
Setting the Active Color .......................................... 31
■
DNIe (Digital Natural Image engine) ......................32
■
Setting the Color Gamut ......................................... 32
■
Adjusting the Screen Position ................................33
■
Resetting the Picture Settings ................................33
■
Viewing Picture-in-Picture ...................................... 34
■
Freezing the Current Picture .................................. 35
Sound Control
■
Using the Automatic Sound Settings ...................... 36
■
Customizing the Sound ..........................................36
■
Setting the TruSurround XT ....................................37
■
Choosing a Multi-Channel Sound (MTS) Track -
Digital .....................................................................38
■
Choosing a Multi-Channel Sound (MTS) Track -
Analog ....................................................................38
■
Automatic Volume Control ......................................39
■
Selecting the Internal Mute .....................................39
■
Resetting the Sound Settings ................................. 40
Symbols
Press
One-Touch
Button
➢
Note
English - 4
Channel Control
■
Clearing Scrambled Channels
■
Managing Channels ...............................................41
■
Fine Tuning Analog Channels - Analog ..................46
■
Checking the Digital-Signal Strength - Digital ........47
■
LNA (Low Noise Amplifier) ......................................47
Function Description
■
Selecting a Menu Language ...................................48
■
Setting the Time .....................................................48
■
Viewing Closed Captions (On-Screen Text
Messages) - Digital .................................................51
■
Viewing Closed Captions (On-Screen Text
Messages) - Analog ................................................52
■
Using the Game Mode ...........................................53
■
Using the 3D/Dual-View Function ..........................53
■
Using the V-Chip ....................................................54
■
Menu Transparency Level ...................................... 59
■
Setting the HDMI Black Level .................................59
■
Setting the Film Mode - Analog ..............................60
■
Setting the Light Effect ...........................................60
■
Setting the Blue Screen Mode ................................61
■
Adjusting the Melody Sound ...................................61
■
Upgrading the Software ..........................................62
■
Setting the Function Help .......................................62
PC Display
■
Using Your TV as a Computer (PC) Display ..........63
■
Display Modes ........................................................ 64
■
Setting up the TV with your PC ..............................65
■
Changing the Picture Size (PC Mode) ...................67
■
Setting the Home Theater PC ................................67
Bluetooth
■
What is Bluetooth? .................................................68
■
Bluetooth Communication and Setting Up PIN ......68
■
Connecting a Bluetooth Headset (Optional) ........... 69
■
Capturing and Printing the Screen .........................69
Wiselink
■
Using the WISELINK Function ............................... 70
■
Using the WISELINK Mode ....................................71
■
Using the Photo (JPEG) List ..................................72
■
Using the Music (MP3) List ....................................79
About Anynet+
■
What is Anynet+? ...................................................81
■
Connecting Anynet+ Devices .................................81
■
Setting Up Anynet+ .................................................82
■
Scanning and Switching between Anynet+ Devices
■
Recording ...............................................................83
■
Listening through a Receiver (Home theater)
■
Check Points before Requesting Service ............... 84
Appendix
■
Identifying Problems ............................................... 85
■
Cleaning and Maintaining Your TV .........................86
■
Using Your TV in Another Country .......................... 86
■
Technical Specifications .........................................87
- Digital ................... 40
..82
....84
English - 5
General Information
Viewing Position
To optimize your viewing comfort, please follow the guidelines below for viewing distance.
If viewing for an extended period of time, sit as far back from the screen as possible.
< Top view> < Side view>
50˝ screen :
At least 5.9 feet
56˝ screen :
At least 6.6 feet
61˝ screen :
At least 7.2 feet
➢
When installing the product, make sure to keep it away
from the wall (more than 10cm / 4inches) for ventilation
purposes. Poor ventilation may cause an increase in
the internal temperature of the product, resulting in a
shortened component life and degraded performance.
50˝ screen :
At least 5.9 feet
56˝ screen :
At least 6.6 feet
61˝ screen :
At least 7.2 feet
List of Features
Your TV is designed and engineered using the latest technology. It is a full-featured, high-performance unit that exceeds
industry standards. In addition, it has these special features:
● Easy-to-operate remote control
● Dynamic menus and Navigating menus by using the menu map
● Easy-to-use on-screen menu system you can access from the side panel or remote control
● Automatic timer to turn the TV on and off at any time you choose
● Adjustable picture and sound settings and the ability to memorize your favorite settings
● Automatic channel tuning for up to 181 channels
● A special filter to reduce or eliminate reception problems
● Fine tuning control for the sharpest picture possible
● A built-in multi-channel sound decoder for stereo and bilingual listening
● Built-in, dual channel speakers
● A special sleep timer
● Widescreen TV with adjustable image size
● Life-like clear images provided by DNle technology
● My Color Control mode to correspond with your color preference
● Digital Input jack
● Digital Audio Output (OPTICAL) jack
● Theater Game Mode
● Easy-to-use channel list menu.
● AV network system (Anynet+) that enables you to easily control Samsung audio-video(AV) devices from this TV.
● TV supports wireless connection to selected Bluetooth stereo headsets and photo printers.
● WISELINK enables you to view and play photo (JPEG) and audio files (MP3) through the TV’s WISELINK jack.
Checking Parts
Owner’s Instructions Remote Control
(BP59-00126A)/
AAA Batteries
Warranty Card/
Registration Card/
Safety Guide Manual/
Quick Guide Manual
Power Cord
(3903-000144)
Sold Separately
S-Video Cable Video Cable Antenna Cable
PC Cable PC Audio Cable HDMI/DVI Cable HDMI Cable Optical Cable
1Stereo/2RCA Cable
Component Cables
Viewing the Control Panel
Buttons on the Lower-Right Part of the Panel
The buttons on the lower-right panel control your TV’s basic features, including the on-screen menu.
To use the more advanced features, you must use the remote control.
Cloth-Clean
Audio Cables
➢
The product color and shape may vary depending on the model.
English - 6
Continued...
English - 7
1
SOURCE
Toggles between all the available input sources
(TV, AV1, AV2, S-Video1, S-Video2, Component1,
Component2, PC, HDMI1, HDMI2, HDMI3/DVI, or
USB).
2
MENU
Press to see an on-screen menu of your TV’s features.
3
+ VOL –
Press to increase or decrease the volume.
In the on-screen menu, use the + VOL – buttons as
5
(ENTER)
Press to confirm a selection.
6
POWER
Press to turn the TV on and off.
7
Remote Control Sensor
Aim the remote control towards this spot on the TV.
8
Indicator Lights
Blinks and turns off when the power is on and lights up
in stand-by mode.
you would use the ◄ and ► buttons on the remote
control.
4
CH
Press to change channels.
In the on-screen menu, use the
CH
buttons as
you would use the ▲ and ▼ buttons on the remote
control.
➢
● You can use the channel selection buttons to switch on the TV when it is in standby mode depending on the model.
● When using the on-screen menu the volume adjustment and channel selection buttons have the same function as the
▲/▼/◄/► buttons on the remote control.
● If the remote control no longer works or you have lost it, you can use controls on the panel of the TV.
Indicator Light Key
( : On, : Blinking, : Off)
STAND BY/TEMP TIMER LED Indication
➢
● It takes about 30 seconds for the TV to warm up, so normal brightness may not appear immediately.
● The TV has a fan to keep the inside optic chassis from overheating. You’ll occasionally hear it working.
Standby state.
The picture will automatically appear in about 15 seconds.
Auto Timer ON/OFF has been set and the set will automatically be turned on in about 15 seconds.
A cooling fan inside the set is not operating normally.
Check if the ventilation hole on the side of the set is blocked, because if the inner temperature is too
high, the power will shut off.
LED may be defective. Please contact a certified technician.
Viewing the Connection Panel
Side Panel Jacks
Use the side panel jacks to connect A/V components that will be connected continuously, such as VCR or DVD players.
For more information on connecting equipment, see pages 10~16.
➢
The product color and shape may vary depending on the model.
1
ANT 1 IN (CABLE)/ANT 2 IN (AIR)
75Ω Coaxial connector for Air/Cable Network.
2
HDMI IN 1, HDMI IN 2
Connect to the HDMI jack of a device with HDMI output.
3
HDMI3/DVI IN
Connect to the HDMI jack of a device with HDMI output.
This input can also be used as a DVI connection with
separate analog audio inputs. An optional HDMI/DVI cable
will be necessary to make this connection.
When using an optional HDMI/DVI adapter, the DVI analog
audio inputs on your TV allow you to receive left and right
audio from your DVI device. (Not compatible with PC)
4
RS232C
For service only.
5
DIGITAL AUDIO OUT (OPTICAL)
Connect to a Digital Audio component.
6
DVI IN (AUDIO-L/R)
Connect to the DVI audio output jack of an external device.
7
S-VIDEO (AV IN 1, 2)
Video input for external devices with an S-Video output, such
as a Camcorder or VCR.
8
3D SYNC OUT
Connect to 3D IR Emitter.
9
VIDEO/AUDIO OUT-L/R (AV OUT)
Video/Audio outputs for external devices.
Video output is not avaiable RF(Digital)/Component/PC/
HDMI.
0
WISELINK
Connect an USB mass storage device to view photo files
(JPEG) and play audio files (MP3).
!
VIDEO/AUDIO-L/R (AV IN 1, 2)
Video input for external devices, such as a Camcorder or
VCR.
@
PC IN
Connect to the video output jack on your PC.
#
PC AUDIO IN
Connect to the audio output jack on your PC.
$
COMPONENT IN 1, 2
Video (Y/PB/PR) and audio (L-AUDIO-R) component inputs.
%
POWER IN
Connect the supplied power cord.
English - 8
Continued...
English - 9
Remote Control
You can use the remote control up to a distance of about 23 feet from the TV. When using the remote, always point it directly
at the TV. You can also use your remote control to operate your VCR, Cable box, DVD player, or Set-Top Box.
1
POWER
Turns the TV on and off.
2
Numeric Buttons
Press to directly select a channel.
3
–
Press to select additional channels
being broadcast by the same station.
For example, to select channel “54-3”,
press “54”, then press “–” and “3”.
4
CH LIST
Used to display Channel Lists on the
screen.
5
ANTENNA
Press to select “Air” or “Cable”.
6
VOL +, VOL –
Press to increase or decrease the
volume.
7
MUTE
Press to temporarily cut off the sound.
8
MENU
Displays the main on-screen menu.
9
RETURN
Returns to the previous menu.
0
S.MODE
Press to select the sound mode.
!
P.MODE
Press to select the picture mode.
@
FAV.CH
Press to switch to your favorite
channels.
#
GAME
Press to select the Game mode except
for the TV mode.
$
CAPTION
Controls the caption decoder.
%
3D
Press to select the 3D/Dual-View
mode.
^
SET
Sets the remote to control your TV,
VCR, Cable, DVD, or Set-Top Box.
&
TV, DVD, STB, CABLE, VCR
Press to operate your TV, DVD, STB,
CABLE (box), or VCR.
*
SOURCE
Press to display all of the available
video sources.
(
Press to activate the backlight of the
VOL, CH and the active source button
(TV, DVD, CABLE, STB, VCR) on the
remote control.
)
PRE-CH
Tunes to the previous channel.
a
WISELINK
This function enables you to view and
play photo (JPEG) and audio files
(MP3) from an external device. (See
page 72 (JPEG), 79 (MP3))
b
REC
Use to make a recording.
c
VCR/DVD Functions
- Rewind
- Stop
- Play/Pause
- Fast Forward
d
CH , CH
Press to change channels.
e
EXIT
Press to exit from the menu.
f
UP▲/DOWN▼/LEFT◄/RIGHT►/
ENTER
Use to select on-screen menu items
and change menu values.
g
INFO
Press to display information on the TV
screen.
h
TOOLS
Use to quickly select frequently used
functions.
Anynet+
Runs the Anynet+ view functions and
sets up Anynet+ devices.
i
STILL
Press to stop the action during a
particular scene.
Press again to resume normal video.
j
P.SIZE
Press to change the screen size.
k
Color buttons
Press to add or delete channels and to
store channels to the favorite channel
list in the Channel List menu.
(Refer to pages 41~46)
l
CH /
Displays the available channels in
sequence. (These buttons change
channels in the PIP window only.)
m
PIP
Picture-in Picture ON/OFF.
n
MTS
Press to choose stereo, mono or
Separate Audio Program (SAP
broadcast).
o
RESET
When your remote control does not
work, change the batteries and press
the RESET button for 2-3 seconds
before use.
➢
The performance of the remote control may be affected by bright light.
➢
This is a special remote control for the visually impaired persons, and has Braille points on the POWER, Channel, Volume, STOP,
and PLAY/PAUSE buttons.
Installing Batteries in the Remote Control
1 Lift the cover at the back of the remote control upward as shown in the figure.
2 Install two AAA size batteries.
➢
● Make sure to match the “+” and “–” ends of the batteries with the diagram inside the
compartment.
● Do not mix battery types, i.e. alkaline and manganese.
3 Close the cover as shown in the figure.
➢
Remove the batteries and store them in a cool and dry place if you won’t be using the remote
control for a long time. The remote control can be used up to about 23 feet from the TV.
(Assuming typical TV usage, the batteries last for about one year.)
➢
If the remote control doesn’t work! Check the following
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power cut, or is the power cord unplugged?
5. Is there a special fluorescent light or a neon sign nearby?
Connections
Connecting VHF and UHF Antennas
If your antenna has a set of leads that look like this, see “Antennas with 300 Ω Flat Twin
Leads” below.
If your antenna has one lead that looks like this, see “Antennas with 75 Ω Round Leads”.
If you have two antennas, see “Separate VHF and UHF Antennas”.
Antennas with 300 Ω Flat Twin Leads
If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has 300 Ω twin flat leads, follow the
directions below.
1 Place the wires from the twin leads under the screws on a 300-75 Ω adapter (not supplied).
Use a screwdriver to tighten the screws.
2 Plug the adaptor into the ANT 1 IN (CABLE) or ANT 2 IN (AIR) terminal on the side of the TV.
Antennas with 75 Ω Round Leads
1 Plug the antenna lead into the ANT 1 IN (CABLE) or ANT 2 IN (AIR) terminal on the side of the
TV.
Separate VHF and UHF Antennas
If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before
connecting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics
shops).
1 Connect both antenna leads to the combiner.
2 Plug the combiner into the ANT 1 IN (CABLE) or ANT 2 IN (AIR) terminal on the bottom of the
side panel.
English - 10
English - 11
Connecting Cable TV
To connect to a cable TV system, follow the instructions below.
Cable without a Cable Box
1 Plug the incoming cable into the ANT 1 IN (CABLE) terminal on the side of the TV.
➢
Because this TV is cable-ready, you do not need a cable box to view unscrambled cable
channels.
Connecting to a Cable Box that Descrambles All Channels
1 Find the cable that is connected to the ANT OUT terminal on your cable box.
➢
This terminal might be labeled “ANT OUT”, “VHF OUT” or simply, “OUT”.
2 Connect the other end of this cable to the ANT 1 IN (CABLE) terminal on the side of the TV.
Connecting to a Cable Box that Descrambles Some Channels
If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need
a two-way splitter, an RF (A/B) switch, and four lengths of Antenna cable. (These items are available at most electronics
stores.)
1 Find and disconnect the cable that is connected
to the ANT IN terminal on your cable box.
➢
This terminal might be labeled “ANT IN”, “VHF
IN” or simply, “IN”.
ANT IN
ANT IN
ANT OUT
2 Connect this cable to a two-way splitter.
Incoming
cable
Splitter
3 Connect an Antenna cable between an OUTPUT
terminal on the splitter and the IN terminal on the
cable box.
Incoming
cable
Splitter
Cable Box
4 Connect an Antenna cable between the ANT OUT
terminal on the cable box and the B–IN terminal
on the RF(A/B) switch.
Incoming
cable
Splitter
Cable Box
RF (A/B)
Switch
5 Connect another cable between the other OUT
terminal on the splitter and the A–IN terminal on
the RF (A/B) switch.
6 Connect the last Antenna cable between the OUT
Incoming
cable
Splitter
Cable Box
TV Side
RF (A/B)
Switch
terminal on the RF (A/B) switch and the ANT 1 IN
(CABLE) terminal on the side of the TV.
Incoming
cable
Splitter
Cable Box
RF (A/B)
Switch
After you have made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the “B” position to
view scrambled channels. (When you set the A/B switch to “B”, you will need to tune your TV to the cable box’s output channel, which
is usually channel 3 or 4.)
Connecting a VCR
Video Connection
These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the
instructions on pages 10~11). Skip step 1 if you have not yet connected to an antenna or a cable system.
1 Unplug the cable or antenna from
the side of the TV.
2 Connect the cable or antenna to
the ANT IN terminal on the side of
the VCR.
3 Connect an Antenna Cable
between the ANT OUT terminal
TV Side Panel
on the VCR and the ANT 1 IN
(CABLE) or ANT 2 IN (AIR)
terminal on the TV.
4 Connect a Video Cable between
VCR
the AV IN 1 [VIDEO] (or AV IN 2
[VIDEO]) jack on the TV and the
VIDEO OUT jack on the VCR.
5 Connect Audio Cables between the
AV IN 1 [L-AUDIO-R] (or AV IN 2
[L-AUDIO-R]) jacks on the TV and
the AUDIO OUT jacks on the VCR.
➢
If you have a “mono”
(non-stereo) VCR, use a
2
Audio Cable(Not supplied)5
Video Cable(Not supplied)4
Antenna cable(Not supplied)3
Y-connector (not supplied) to
hook up to the right and left audio input jacks of the TV. If your VCR is stereo, you must connect two cables.
➢
Each VCR has a different side panel configuration.
➢
When connecting a VCR, match the color of the connection terminal to the cable.
1
S-Video Connection
Your Samsung TV can be connected to the S-Video jack of a VCR.
(This connection delivers a better picture when compared to the regular video connection above.)
1 To begin, follow steps 1–3 in the
previous section to connect the
antenna or cable to your VCR and
your TV.
2 Connect an S-Video Cable
between the AV IN 1 [S-VIDEO] (or
AV IN 2 [S-VIDEO]) jack on the TV
and the S-VIDEO OUT jack on the
VCR.
3 Connect Audio Cables between the
AV IN 1 [L-AUDIO-R] (or AV IN 2
[L-AUDIO-R]) jacks on the TV and
the AUDIO OUT jacks on the VCR.
➢
Each VCR has a different side panel configuration.
➢
When connecting a VCR, match the color of the connection terminal to the cable.
➢
Some games may be displayed with a cut off picture when the TV is connected to a game player.
VCR
Audio Cable
3
1
(Not supplied)
S-Video Cable(Not supplied)2
Antenna cable(Not supplied)1
TV Side Panel
English - 12
English - 13
Connecting a Camcorder
The side panel jacks on your TV make it easy to connect a camcorder to your TV.
They allow you to view the camcorder tapes without using a VCR
1 Connect a Video Cable or S-Video
Cable between the AV IN 1 [VIDEO]
or [S-VIDEO] (or AV IN 2 [VIDEO] or
[S-VIDEO]) jack on the TV and the
VIDEO OUT or S-VIDEO OUT jack
on the camcorder.
Camcorder
2 Connect Audio Cables between
the AV IN 1 [L-AUDIO-R] (or AV IN
2 [L-AUDIO-R]) jacks on the TV
and the AUDIO OUT jacks on the
camcorder.
➢
Each Camcorder has a different side panel configuration.
➢
When connecting a Camcorder, match the color of the connection terminal to the cable.
S-Video Cable(Not supplied)
1
or
1
Video Cable(Not supplied)
Audio Cable(Not supplied)
2
TV Side Panel
Connecting a DVD Player/Set-Top Box
The side jacks on your TV make it easy to connect a DVD player/Set-Top Box
1 Connect Component Cables
between the COMPONENT IN 1
[Y, PB, PR] (or COMPONENT IN
2 [Y, PB, PR]) jacks on the TV and
DVD Player/Set-Top Box
the COMPONENT OUT [Y, PB, PR]
jacks on the DVD Player/Set-Top
Box.
2 Connect Audio Cables between the
COMPONENT IN 1 [L-AUDIO-R]
(or COMPONENT IN 2 [L-AUDIOR]) jacks on the TV and the AUDIO
OUT jacks on the DVD player/SetTop Box.
➢
Component video separates the video into Y Luminance (brightness), PB (Blue) and PR (Red) for enhanced video quality.
Be sure to match the component video and audio connections.
2
Audio Cable(Not supplied)
Component Cable(Not supplied)
1
For example, if connecting the video cable to COMPONENT IN, connect the audio cable to COMPONENT IN also.
➢
Each DVD Player/Set-Top box has a different side panel configuration.
➢
When connecting a DVD Player/Set-Top box, match the color of the connection terminal to the cable.
TV Side Panel
Connecting a DVD Player/Set-Top Box via HDMI
This connection can only be made if there is an HDMI Output jack on the external device.
1 Connect an HDMI Cable between
the HDMI IN 1 (or HDMI IN 2 ) on
the TV and the HDMI OUT jack on
the DVD Player/Set-Top Box.
What is HDMI?
● HDMI, or high-definition multimedia interface, is a next-generation interface that enables the transmission of the digital audio and
video signals using a single cable.
● “Multimedia interface” is a more accurate name for it especially because it allows multiple channels of digital audio (5.1 channels).
The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP (High Bandwidth Digital Copy
Protection) coding feature installed, and supports multi-channel digital audio.
➢
Each DVD Player/Set-top box has a different side panel configuration.
➢
When connecting a DVD Player/Set-top box, match the color of the connection terminal to the cable.
➢
When connecting via HDMI, you do not need to connect Audio Cables. You only need to connect Audio cables when connecting
via HDMI/DVI.
TV Side Panel
1
HDMI Cable(Not supplied)
DVD Player/Set-Top Box
Connecting a DVD Player/Set-Top Box via DVI
This connection can only be made if there is a DVI Output jack on the external device.
1 Connect a HDMI/DVI Cable or
DVI-HDMI Adapter between the
HDMI3/DVI IN jack on the TV and
the DVI OUT jack on the DVD
Player/Set-Top Box.
2 Connect Audio Cables between
the DVI IN [L-AUDIO-R] jacks on
the TV and the AUDIO OUT jacks
on the DVD Player/Set-Top Box.
➢
Each DVD Player/Set-Top box has a different side panel configuration.
➢
When connecting a DVD Player/Set-Top box, match the color of the connection terminal to the cable.
DVD Player/Set-Top Box
2
Audio Cable(Not supplied)
HDMI/DVI Cable(Not supplied)
1
TV Side Panel
English - 14
English - 15
Connecting a Digital Audio System
The side panel jacks on your TV make it easy to connect a Digital Audio System to your TV.
1 Connect an Optical Cable
between the DIGITAL AUDIO OUT
(OPTICAL) jack on the TV and
the Digital Audio Input jack on the
Digital Audio System.
When a Digital Audio System
is connected to the DIGITAL
AUDIO OUT (OPTICAL) terminal:
Decrease the volume of the TV,
and adjust the volume level with
the audio system’s volume control.
➢
Each Digital Audio System has a different side panel configuration.
➢
5.1CH audio is possible when the TV is connected to an external device supporting 5.1CH.
What is OPTICAL?
● Converts the electric signal into an optical light signal, and transmits it through glass fibers. S/PDIF is a transmission system of
digital audio in the form of a light wave that uses a glass conductor.
Digital Audio System
1
Optical Cable (Not supplied)
TV Side Panel
Connecting an Amplifier/DVD Home Theater
1 Connect Audio Cables between
the AV OUT [L-AUDIO-R] jacks on
the TV and AUDIO IN [L-AUDIO-R]
jacks on the Amplifier/DVD Home
Theater.
When an audio amplifier is
connected to the AV OUT [LAUDIO-R] terminals: Decrease the
volume of the TV, and adjust the
volume level with the amplifier’s
volume control.
➢
Each Amplifier/DVD Home Theater has a different side panel configuration.
➢
When connecting an Amplifier/DVD Home Theater, match the color of the connection terminal to the cable.
Amplifier/DVD Home Theater
1
Audio Cable (Not supplied)
TV Side Panel
Connecting a PC
Using the D-Sub Cable
1 Connect a D-Sub Cable between
the PC IN [PC] jack on the TV
and the PC output jack on your
computer.
2 Connect a PC Audio Cable
between the PC IN [AUDIO] jack
on the TV and the Audio Out
jack of the sound card on your
computer.
Using the D-Sub Cable
PC
2
PC Audio Cable (Not supplied)
1
D-Sub Cable (Not supplied)
TV Side Panel
Using the HDMI/DVI Cable
1 Connect a HDMI/DVI Cable
between the HDMI3/DVI IN jack on
the TV and the PC output jack on
your computer.
2 Connect a 1Stereo/2RCA Cable
between the DVI IN [L-AUDIO-R]
jack on the TV and the Audio Out
jack of the sound card on your
computer.
➢
Each PC has a different side panel configuration.
➢
When connecting a PC, match the color of the connection terminal to the cable.
➢
When connecting the HDMI/DVI to your PC, select HDMI3/DVI in Edit Name from you PC to see the original screen with no cutting
images. See page 27.
Using the HDMI/DVI Cable
PC
2
1Streo/2RCA Cable (Not supplied)
1
TV Side Panel
HDMI/DVI Cable (Not supplied)
Operation
Turning the TV On and Off
Press the POWER button on the remote control.
You can also use the POWER button on the TV.
➢
It may take a while when your TV starts.
English - 16
English - 17
Plug & Play Feature
When the TV is initially powered on, basic settings proceed automatically:
1 Press the POWER button on the remote control.
The message Executes the Plug & Play function when you set the TV at first or
reset it. Sets channels, clock and other functions. is automatically displayed.
2 Press the ENTER button to enter the language.
Press the ▲ or ▼ button to select language, then press the ENTER button.
The message Select Home Mode when installing this TV at home. is automatically
displayed.
3 Press the ◄ or ► button to select Shop or Home, then press the ENTER button.
➢
The default selection is Home.
➢
We recommend setting the TV to Home mode for the best picture in your home
environment.
➢
Shop mode is only intended for use in retail environments.
➢
If the unit is accidentally set to Shop mode, and you want to return to Dynamic
(Home) mode, press the Volume button and then hold down the
MENU button for
five seconds on the TV panel.
4 Press the ▲ or ▼ button to memorize the channels of the selected connection, then
press the ENTER button.
➢
If the antenna is connected to ANT 1 IN (CABLE), select Cable and if it is
connected to ANT 2 IN (AIR), select Air.
➢
If both ANT 1 IN (CABLE) and ANT 2 IN (AIR) are connected, select the Air +
Cable.
➢
In Cable mode, you can select the correct analog signal source among STD, HRC,
and IRC by pressing the ◄ or ► button, then press the ENTER button. If you have
Digital cable, select the signal source for both Analog and Digital.
Contact your local cable company to identify the type of cable system that exists in
your particular area.
5 The TV will begin memorizing all of the available channels.
After all the available channels are stored, the Auto program menu reappears.
Press the ENTER button when channel memorization is complete.
The Clock Mode menu is displayed.
➢
To stop the search before it has finished, press the ENTER button with stop
selected.
Executes the Plug & Play function when you set the TV
at first or reset it. Sets channels, clock and other
functions.
Select Language of the OSD.
Menu Language : English
Select Home Mode when installing this TV at home.
Select the antennas to memorize
Air
Cable
Air+Cable
Selects the cable system.
Analog
Digital
Auto Program in Progress.
Digital Channels are added on the favorite
channel list.
Auto Program is completed.
3 channels are memorized.
Air : 1 Cable : 2
Shop
STD
STD
Plug & Play
OK
Plug & Play
Move
Plug & Play
Move
Plug & Play
Move
Plug & Play
Move
Plug & Play
Stop
Plug & Play
OK
Enter
Exit
English
Español
Français
SkipEnter
Home
SkipEnter
Start
Start
Start
SkipEnter
HRC IRC
HRC IRC
SkipEnter
Cable 10
3%
SkipEnter
SkipEnter
Continued...
6 Press the ENTER button.
Press the ▲ or ▼ button to select Manual for setting the current time manually, then
press the ENTER button. The message Set current date and time. is displayed.
➢
If you select Auto. Set to daylight saving time. is displayed, then go to step 9.
Set the Clock Mode.
Clock Mode : Auto
7 Press the ◄ or ► button to move to Month, Day, Year, Hour, Minute, or am/pm.
Set the date and time you want by pressing the ▲ or ▼ button, then press the ENTER
button.
➢
You can set the month, day, year, hour, and minute directly by pressing the number
buttons on the remote control.
Set the Clock Mode.
Clock Mode : Auto
8 The message Enjoy your watching. is displayed.
When you have finished, press the ENTER button.
➢
Even if the ENTER button is not pressed, the message will automatically disappear
after several seconds.
Set current date and time
Setting the Clock Automatically
9 Press the ENTER button.
Press the ▲ or ▼ button to select Off or On, then the ENTER button.
The message Select the time zone in which you live. is displayed.
10 Press the ▲ or ▼ button to highlight the time zone for your local area (and to move the
highlight to the appropriate time zone on the map of the United States).
Press the ENTER button.
If clock is not automatically set, see pages 48~49 to set the clock.
11 The message
Enjoy your watching. is displayed.
When you have finished, press the ENTER button.
➢
Even if the ENTER button is not pressed, the message will automatically disappear
after several seconds.
Set to daylight saving time.
DST : Off
Set to daylight saving time.
DST : Off
Select the time zone in which you live.
Newfoundland
Atlantic
Eastern
Central
Mountain
Pacific
Month
Hour
Move
Plug & Play
Plug & Play
Auto
Manual
Move
Plug & Play
Day
Minute
Enter
Adjust
Plug & Play
Plug & Play
Off
On
Move
Plug & Play
Move
Plug & Play
Enjoy your watching.
SkipEnter
SkipEnter
Year
am/pm
SkipEnter
SkipEnter
SkipEnter
Skip
English - 18
OK
English - 19
Changing Channels
Using the Channel Buttons
Press the CH or CH button to change channels.
➢
When you press the CH or CH button, the TV changes channels in sequence.
You will see all the channels that the TV has memorized. (The TV must have memorized at
least three channels). You will not see channels that were either erased or not memorized.
See page 21 to memorize channels.
Using the Number Buttons
Use the number buttons to quickly tune to any channel.
Press the number buttons to go directly to a channel.
For example, to select channel 27, press “2,” then “7.”
The TV will change channels when you press the second number.
Using the “-” Button
The “-” button is used to select stations that broadcast a digital signal.
For example, for Channel 7-1, press “7”, then “-”, and then “1”.
➢
HD indicates the TV is receiving a Digital High Definition signal.
SD indicates the TV is receiving a Standard Definition signal.
➢
For quick channel change, press the number buttons, then press the ENTER button.
Using the PRE-CH Button to select the Previous Channel
Press the PRE-CH button.
The TV will switch to the last channel viewed.
➢
To quickly switch between two channels that are far apart, tune to one channel, then use
the number button to select the second channel. Then use the PRE-CH button to quickly
alternate between them.
Adjusting the Volume
Press the VOL + or VOL – button to increase or decrease the volume.
Using the Mute Button
At any time, you can cut off the sound using the MUTE button.
1 Press the MUTE button and the sound cuts off.
The is displayed on the screen.
2 To turn mute off, press the MUTE button again, or simply press the VOL + or VOL – button.
Viewing the Display
The display identifies the current channel and the status of certain audio-video settings.
Press the INFO button on the remote control.
Viewing the Menus
1 With the power on, press the MENU button.
The main menu will appear at the bottom of the screen.
There are seven menu groups: Picture, Sound, Channel, Setup, Input, Guide,
and PIP.
2 Press the ▲ or ▼ button, then press the ENTER button to select an item you want in the
menu. Press the ▲/▼/◄/►/ENTER button to display, change, or use the selected items.
Press the EXIT button to exit.
Air
3
Picture
Mode
Contrast : 100
Brightness : 45
Sharpness : 75
Color : 55
Tint (G/R) : G50/R50
Color Tone : Cool1
Detail Settings
:
No Time Information
Dynamic
Using the TOOLS Button
The Tools button allows you to display frequently used Menu and Connection items
with a Single button press.
1 Press the TOOLS button.
The TOOLS menu will appear.
2 Press the ▲/▼ button to select a menu, then press the ENTER button.
3 Press the ▲/▼/◄/►/ENTER buttons to display, change, or use the selected items.
For a more detailed description of each function, refer to the corresponding page.
● Device List, see page 82
Headset Connection, see page 69
Picture Setting, see page 28
Sound Setting, see page 36
Sleep Timer, see page 50
Caption, see page 51~52
Channel Add/Delete, see page 42
Delete Favorite Channel, see page 43
Auto Program, see page 21
Device List
Headset Connection
Picture Setting
Sound Setting
Sleep Timer Off
Caption
Channel Add/Delete
Delete Favorite Channel
Move
Off
Enter
English - 20
English - 21
Memorizing the Channels
Your TV can memorize and store all of the available channels for both “off-air”(air) and cable channels. After the available
channels are memorized, use the CH and CH button to scan through the channels. This eliminates the need to change
channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source,
memorizing the channels(automatic) and adding or deleting channels(manual).
Selecting the Video Signal-source
Before your television can begin memorizing the available channels, you must specify the type of signal source that is
connected to the TV(i.e. an air or a cable system).
1 Press the MENU button.
Press the ▲ or ▼ button to select Channel, then press the ENTER button.
Press the ENTER button to select Antenna.
2 Press the ▲ or ▼ button to select Air or Cable, then press the ENTER button.
Channel
Channel
Antenna
:
Channel List
Auto Program
Clear Scrambled Channel
Fine Tune
Signal Strength
LNA : On
Antenna
:
Channel List
Auto Program
Clear Scrambled Channel
Fine Tune
Signal Strength
LNA : On
Air
Air
Air
Cable
Storing Channels in Memory (Automatic Method)
3 Press the ▲ or ▼ button to select Auto Program, then press the ENTER button.
4 Press the ▲ or ▼ button to select an antenna connection, then press the ENTER
button.
➢
Air: “Air” antenna signal.
Cable: “Cable” antenna signal.
Air+Cable: “Air” and “Cable” antenna signals.
➢
If the antenna is connected to ANT 1 IN (CABLE), select Cable and if it is
connected to ANT 2 IN (AIR), select Air.
➢
If both ANT 1 IN (CABLE) and ANT 2 IN (AIR) are connected, select the
Air+Cable.
➢
If you selected Air, then go to step 6.
5 Press the ◄ or ► to select the correct analog signal source among STD, HRC, and
IRC, then press the ENTER button. If you have Digital cable, select the signal source for
both Analog and Digital.
➢
STD, HRC, and IRC identify various types of cable TV systems.
Contact your local cable company to identify the type of cable system that exists in
your particular area. At this point the signal source has been selected.
6 The TV begins memorizing all available stations.
When pressing the ENTER button during a storing process, the message Would you
like to stop the auto channel selection? is displayed. Select Yes by pressing the ◄
or ► button.
Press the EXIT button to exit.
➢
The TV must be connected to an antenna/cable in order to receive digital TV
signals. Even if a particular channel is deleted from the memory, you can always
tune to that channel directly by using the number buttons on the remote control.
➢
All available DTV and analog channels are automatically stored in memory.
It takes approximately 3 to 10 minutes to memorize channels.
Auto Program
Select the antennas to memorize
Air
Cable
Air+Cable
Move
Auto Program
Select the cable system.
Analog
Digital
Auto Program in Progress.
Digital Channels are added on the favorite
channel list.
Would you like to stop the auto channel
selection ?
Digital Channels are added on the favorite
channel list.
Auto Program is incomplete.
3 channels are memorized.
Air : 1 Cable : 2
STD
Yes
HRC IRC
HRC IRCSTD
Move
Auto Program
Stop
Auto Program
Move
Auto Program
OK
No
Enter
Enter
Start
Start
Start
ReturnEnter
ReturnEnter
Air 10
3%
SkipEnter
Air 10
3%
Return
Return
Setting Up Your Remote Control
After your remote control has been properly set up, your remote control can operate in five different modes: TV, VCR, Cable,
DVD, or Set-Top Box. Pressing the corresponding button on the remote control allows you to switch among these modes,
and control whichever piece of equipment you choose.
➢
The remote control might not be compatible with all DVD Players, VCRs, Cable boxes, and Set-Top Boxes.
Setting Up the Remote to Operate Your VCR
1 Turn off your VCR.
2 Press the VCR button on your TV’s remote control.
3 Press the SET button on your TV’s remote control.
4 Using the number buttons on your remote control, enter three digits of the VCR code listed
on page 24 of this manual for your brand of VCR. Make sure you enter three digits of the
code, even if the first digit is a “0”. (If more than one code is listed, try the first one.)
5 Press the POWER button on the remote control. Your VCR should turn on if your remote is
set up correctly.
If your VCR does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other
codes listed for your brand of VCR. If no other codes are listed, try each VCR code, 000
through 080.
Note on Using Remote Control Modes: VCR
When your remote control is in
VCR mode, the volume buttons still control your TV’s volume.
Setting Up the Remote to Operate Your Cable Box
1 Turn off your cable box.
2 Press the CABLE button on your TV’s remote control.
3 Press the SET button on your TV’s remote control.
4 Using the number buttons on your remote control, enter three digits of the cable box code
listed on page 25 of this manual for your brand of cable box. Make sure you enter three
digits of the code, even if the first digit is a “0”. (If more than one code is listed, try the first
one.)
5 Press the POWER button on the remote control.
Your cable box should turn on if your remote is set up correctly.
If your cable box does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the
other codes listed for your brand of cable box. If no other codes are listed, try each code, 000
through 046.
Note on Using Remote Control Modes: Cable Box
When your remote control is in
volume.
CABLE mode, the volume buttons still control your TV’s
English - 22
Continued...
English - 23
Setting Up the Remote to Operate Your DVD
1 Turn off your DVD.
2 Press the DVD button on your TV’s remote control.
3 Press the SET button on your TV’s remote control.
4 Using the number buttons on your remote control, enter three digits of the DVD code listed
on page 26 of this manual for your brand of DVD. Make sure you enter three digits of the
code, even if the first digit is a “0”. (If more than one code is listed, try the first one.)
5 Press the POWER button on the remote control.
Your DVD should turn on if your remote is set up correctly.
If your DVD does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other
codes listed for your brand of DVD. If no other codes are listed, try each code, 000 through
141.
Note on Using Remote Control Modes: DVD
When your remote control is in
TV’s volume.
DVD mode, the volume buttons still control your
Setting Up the Remote to Operate Your Set Top Box
1 Turn off your STB.
2 Press the STB button on your TV’s remote control.
3 Press the SET button on your TV’s remote control.
4 Using the number buttons on your remote control, enter three digits of the STB code listed
on page 25 of this manual for your brand of STB. Make sure you enter three digits of the
code, even if the first digit is a “0”. (If more than one code is listed, try the first one.)
5 Press the POWER button on the remote control.
Your STB should turn on if your remote is set up correctly.
If your STB does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other
codes listed for your brand of STB. If no other codes are listed, try each code, 000 through 074.
Note on Using Remote Control Modes: STB
When your remote control is in
STB mode, the volume buttons still control your TV’s volume.
Continued...
Remote Control Codes
VCR
Brand
SAMSUNG
ADMIRAL
AIWA
AKAI
AUDIO DYNAMICS
BELL&HOWELL
BROKSONIC
CANDLE
CANON
CITIZEN
COLORTYME
CRAIG
CURTIS MATHES
DAEWOO
DB
DIMENSIA
DYNATECH
ELECTROHOME
EMERSON
FISHER
FUNAI
GENERAL ELECTRIC
GO VIDEO
LG(Goldstar)
HARMAN KARDON
HITACHI
INSTANT REPLAY
JC PENNEY
JCL
KENWOOD
KLH
LIOYD
LOGIK
LXI
JVC
MAGNAVOX
MARANTZ
MARTA
KONIA
ORION
MEI
MEMOREX
MGA
MIDLAND
MINOLTA
Code
000 001 002 003 004 005 077 078 079
020
025
004 027 032
007 026
018
022
002 003 006 008 015 055
021 056
002 003 006 008 015 055
007
002 024
002 007 008 017 021 025 056 064 066
003 010 011 012 013 014 015 016
007 026
017
025
034
001 003 006 021 022 025 030 032 034
040 047 050 052 060 063 065 066 067
069 073
018 024 028 029 048 051 061
025
002 005 017 021 056
002
006 007 008 009 010
007
019 025 041 042 074
021
002 007 018 019 021 026 037 041
054 056
007 008 018 021 026 037
007 008 018 026 037
070
025
038
025
081 082 083
021 056 059
007 008 018 021 026 037 062
006
036
073 074 075 076
021
006 021 024 025
034
005
019 041 075
Brand
MITSUBISHI
MONTGOMERY WARD
MTC
MULTITECH
NEC
OPTIMUS
PANASONIC
PENTAX
PENTEX RESEARCH+
PHILCO
PHILIPS
PIONEER
PORTLAND
PROSCAN
QUARTZ
QUASAR
RADIO SHACK/
REALISTIC
RCA
SANSUI
SANYO
SCOTT
SEARS
SHARP
SHIMTOM
SIGNATURE
SONY
SYLVANIA
SYMPHONIC
TANDY
TASHIKA
TATUNG
TEAC
TECHNICS
TEKNIKA
TMK
TOSHIBA
TOTEVISION
UNITECH
VECTOR RESEARCH
VICTOR
VIDEO CONCEPTS
VIDEOSONIC
WARDS
YAMAHA
ZENITH
Code
019 034 041 046
020
002 025
002 005 025 038
007 008 018 026 037 062 064
020
021 056 071 072
019 041 075
008
021 056 059
021 080
019 026 039 053
015 049 055
017
018
021 056
006 018 020 021 024 025 029 034
048 056
002 017 019 021 035 041 043 057
068 076
026
018 024
003 047 052 067
006 018 019 024 028 029 041 048 051
020 034 045 015
027 033 038 058
025
027 033 044
021 025 056 059
025
018 025
006
037
025 037 068
021
006 021 025 031
066
003 019 029 051 052
002 006
002
007 026
026
007 026
002
002 003 006 019 020 021 024 025 034
038 041
007 008 018 026 037
023 027 033
English - 24
Continued...
English - 25
CABLE BOX
Brand
SAMSUNG
GI
HAMLIN
HITACHI
JERROLD
MACOM
MAGNAVOX
OAK
PANASONIC
PHILIPS
PIONEER
RCA
REGAL
Code
000 001 002 003 004 005 006 007
041
003 024 031
025 030
038 039
025 030
019 023 028
026
003 022 027 037 044
019 021 023 028
004 018 020 044
014 022 040
003
SAMSUNG SET-TOP BOX
Product
Ground wave STB
Satellite STB
CABLE STB
STB DVD COMBO
Satellite STB HDD COMBO Standard
SET-TOP BOX
Brand
ALPHASTAR
ANAM
CHANNEL MASTER
CROSSDIGITAL
CHAPARRAL
DIRECT TV
DAEWOO
DISH NETWORK SYSTEM
DISHPRO
DRAKE
DX ANTENNA
ECHOSTAR
EXPRESSVU
GOI
GE
GENERAL INSTRUMENT
HTS
HOME CABLE
HITACHI
HUGHES NETWORK
IQ
IQ PRISM
JANEIL
JERROID
JVC
Code
023
043
018 034
019
035
015 016 017 019 022 045 060
061 062 065 066 067 068
074
069 070
069
018 024 032
027
025 069 070 071
069
069
065
046 047 048 063 064
069
056
022
015 017
020
020
059
063
069 070
Code
001 002
003
004
008
009
Brand
REGENCY
SA
SCIENTIFIC ATLAN
SPRUCER
STARGATE 2000
SYLVANIA
TEXSCAN
TOCOM
UNIVERSAL
VIEWSTAR
WARNER AMEX
ZENITH
Product
Satellite STB HDD COMBO Premium
CABLE STB HDD COMBO Standard
CABLE STB HDD COMBO Premium
Ground wave STB HDD COMBO Standard
Ground wave STB HDD COMBO Premium
Brand
LG(Goldstar)
MAGNAVOX
MEMOREX
MOTOROLA
MACOM
MITSUBISHI
NEXT LEVEL
PHILIPS
PRIMESTAR
PANASONIC
PAYSAT
PROSCAN
RCA
RADIOSHACK
REALISTIC
STS
STAR TRAK
SKY
SKY LIFE
SHACK
STAR CHOICE
SONY
TOSHIBA
ULTIMATE TV
UNIDEN
ZENITH
Code
015 023
042 043
042 043
022
036
016
016
032
033 034
019 021 023 028
046
017 029 035 037 045
Code
010
011
012
013
014
Code
044 073
016 021 036 038 039 040 041 042
016
064
018
015
047 048 064
015 016 017 021 033 036 038 039
040 041 042 067
046 049 050 063
058 059 061 062
016
065 066
051 052 053 065 066
064
057
020 027
026
031
005 006 007
064
064
054 060
015 017 028 029 030 072
060 066
016 021 037 055 056 057
024 031 068
Continued...
SAMSUNG DVD
Product
DVD
DVDR
BD Record
VCR COMBO
VCR Record
DHR COMBO
DVD
Brand
ANAM
AUDIOVOX
AUDIOLOGIC
ANABA
APEX DIGITAL
AIWA
BROKSONIC
BLAUPUNKT
B&K
CURTIS MATHES
CYBER HOME
CLARION
CIRRUS
CINEVISION
DAEWOO
DENON
FARENHEIT
FISHER
GPX
GO VIDEO
GE
GREENHILL
HITACHI
HITEKER
HOYO
HARMAN / KARDON
IRT
INTEGRA
JBL
JVC
JATON
KENWOOD
KISS
KONKA
KLH
LG(Goldstar)
LOEWE
LASONIC
MOBILE AUTHORITY
MEMOREX
MALATA
MAGNAVOX
MINTEK
MONYKA
Code
000 001 002
003 004
005 006
007 008 009 010 011
012
013
Code
030
075
085
072
070 071 074 086 083 084 088
111 112
114
062
074
122 123
027
065 077 078 079 082
080 125
081
095
066
146
067 068
090
060
061 089 133 135
069 074
074
064 113
071
073
091 110
089
092
091
022 033 115 116
073
051 108 109
073
059 100 106 107
074 075
025 031
057
058
054
055
056
076 093
074 094
073
Product
Home Theater VCR COMBO
HDD Record COMBO
TWIN TRAY COMBO
STB DVD COMBO
DVD Receiver
AV Receiver
Brand
NORCENT
NEXT BASE
NEC
NANTAUS
NESA
OPTOMEDIA ELECTRONICS
OPTIVIEW
ONKYO
PHILCO
PRINCETON
PROSCAN
PANASONIC
PHILIPS
ROTEL
RIO
RCA
RAITE
ROWA
SAMPO
SONY
SHERWOOD
SVA
SYLVANIA
SHARP
SANSUI
SANYO
SHINSONIC
SANYO
THOMSON
TOSHIBA
TECHNICS
TVIEW
TOKAI
TEAC
TECHWOOD
TREDEX
URBAN CONCEPTS
VENTURER
VOCOPRO
YAMAHA
YAMAKAWA
XWAVE
ZENITH
Code
014 015 016
017
018
019
020
021
Code
048 049 050
052
053
144
074
105
072
076 092 119
044 045
046 047
023
024 034 124 134 136 137 138
036 076
117 118
120
023 035 074 075 131 132
073
038
104
026 029 126 127 128 129
130 141
039 041
042
043 093
140
062
062
094
090
145
028 062 076
139
072
073
096
097
098 099 101
076
075
102
032 063
040 073
103
076 121
English - 26
English - 27
To Select the Source
Use to select TV or other external input sources such as DVD players, VCRs, etc. connected to the TV.
1 Press the MENU button.
Press the ▲ or ▼ button to select Input, then press the ENTER button.
Press the ENTER button to select Source List.
2 Press the ▲ or ▼ button to select a signal source, then press the ENTER button.
Press the EXIT button to exit.
➢
You can choose between the following sets of jacks: TV, AV1, AV2, S-Video1, S-Video2,
Component1, Component2, PC, HDMI1, HDMI2, HDMI3/DVI, or USB on the TV’s side
panel.
➢
HDMI1, HDMI2, or HDMI3/DVI input can only be selected when the external device is
turned on and connected via HDMI.
➢
You can choose only those external devices that are connected to the TV.
Press the SOURCE button on the remote control to view an external signal source.
Input
Source List
Edit Name
TV
AV1
AV2
S-Video1
S-Video2
Component1
Component2
Refresh Option
----
----
----
----
----
----
To Edit the Input Source Name
Name the external device connected to the input jacks to make your input source selection easier.
1 Press the MENU button.
Press the ▲ or ▼ button to select Input, then press the ENTER button.
Press the ▲ or ▼ button to select Edit Name, then press the ENTER button.
2 Press the ▲ or ▼ button to select AV1, AV2, S-Video1, S-Video2, Component1,
Component2, PC, HDMI1, HDMI2, or HDMI3/DVI input jack, then press the ENTER
button.
3 Press the ▲ or ▼ button to select VCR, DVD, D-VHS, Cable STB, HD STB, Satellite
STB, PVR STB, AV Receiver, DVD Receiver, Game, Camcorder, DVD Combo, DVD
HDD Recorder, PC, Internet TV Recv., Interactive TV Recv., VOD STB, or TV input
source, then press the ENTER button.
Press the EXIT button to exit.
Input
AV1 :
AV2 :
S-Video1 :
S-Video2 :
Component1 :
Component2 :
PC :
AV1 :
AV2 :
S-Video1 :
S-Video2 :
Component1 :
Component2 :
PC :
Source List
Edit Name
Edit Name
----
----
----
----
----
----
----
Enter
Enter
Return
Return
Move
Edit Name
----
----
----
----
----
----
----
Move
---VCR
DVD
D-VHS
Cable STB
HD STB
Picture Control
Using Automatic Picture Settings
Your TV has three automatic picture settings (“Dynamic”, “Standard”, “Movie”) that are preset at the factory.
You can activate a Picture Setting by making a selection from the menu.
1 Press the MENU button.
Press the ENTER button to select Picture.
Press the ENTER button again to select Mode.
2 Press the ▲ or ▼ button to select Dynamic, Standard, or Movie, then press the
ENTER button.
Choose Dynamic to increase the clarity and sharpness of the picture.
Choose Standard for general TV watching mode.
Choose Movie when watching movies.
Press the P.MODE button on the remote control to select one of the standard picture
settings.
Picture Picture
Mode
Contrast : 100
Brightness : 45
Sharpness : 75
Color : 55
Tint (G/R) : G50/R50
Color Tone : Cool1
Detail Settings
Mode
Contrast : 100
Brightness : 45
Sharpness : 75
Color : 55
Tint (G/R) : G50/R50
Color Tone : Cool1
Detail Settings
:
:
Dynamic
Dynamic
Dynamic
Standard
Movie
3 Press the ▲ or ▼ button to select Contrast, Brightness, Sharpness, Color, or
Tint (G/R), then press the ENTER button.
➢
Tint (G/R) is not available in DTV or PC mode.
4 Press the ◄ or ► button to decrease or increase the value of a particular item.
Press the ENTER button.
➢
● Each adjusted setting will be stored separately according to its input mode.
● When you make changes to Contrast, Brightness, Sharpness, Color, or
Tint (G/R), OSD color will also be adjusted accordingly.
5 Press the ▲ or ▼ button to select Color Tone, then press the ENTER button.
Mode : Dynamic
Picture
:
Contrast
Brightness : 45
Sharpness : 75
Color : 55
Tint (G/R) : G50/R50
Color Tone : Cool1
Detail Settings
Size : 16:9
AdjustMove
Color : 55
:
Tint (G/R)
Picture
Color Tone : Cool1
Detail Settings
Size : 16:9
Digital NR : Auto
Active Color : On
DNIe : On
Color Gamut
Position
100
100Contrast
Enter
Return
G50/R50
: Wide
English - 28
Continued...
English - 29
6 Press the ▲ or ▼ button to select Cool2, Cool1, Normal, Warm1, or Warm2, then
press the ENTER button.
➢
When the picture mode is set to Dynamic or Standard, Warm1, and Warm2
cannot be selected.
Press the EXIT button to exit.
Color : 55
Tint (G/R)
Picture Picture
Color Tone : Cool1
Detail Settings
Size : 16:9
Digital NR : Auto
Active Color : On
DNIe : On
Color Gamut
Position
Making Detail Settings on the Picture
Samsung’s new TVs allow you to make even more precise picture settings than previous models.
See below to make Detailed picture settings.
1 Press the MENU button.
Press the ENTER button to select Picture.
Press the ▲ or ▼ button to select Detail Settings, then press the ENTER button.
2 Select the required option by pressing the ▲ or ▼ button, then press the ENTER
button.
3 When you are satisfied with your setting, press the ENTER button.
Press the EXIT button to exit.
➢
When the picture mode is set to Standard or Movie, Detail Settings can be
selected.
➢
If DNIe is set to Off and the picture mode is in Dynamic or Standard mode, the
Detailed Settings cannot be selected.
Tint (G/R) : G50/R50
Color Tone
Detail Settings
Size : 16:9
Digital NR : Auto
Active Color : On
DNIe : On
Color Gamut
Position
Picture Reset
Black Adjust : Medium
Dynamic Contrast : Medium
Gamma : +1
White Balance : 0
My Color Control
Edge Enhancement : On
xvYCC : Off
:
:
Detail Settings
Move
G50/R50
Cool2
Cool1
Normal
Warm1
Warm2
: Wide
Cool1
: Wide
ReturnEnter
● Black Adjust: Off/Low/Medium/High
You can directly select the black level on the screen to adjust the screen depth.
● Dynamic Contrast: Off/Low/Medium/High
You can adjust the screen contrast so that the optimal contrast is provided.
● Gamma: -3 ~ +3
You can adjust the Primary Color (Red, Green Blue) Intensity.
Press the ◄ or ► button until you reach the optimal setting.
● White Balance: -10 ~ +10
You can adjust the color temperature for more natural picture colors.
Press the ◄ or ► button until you reach the optimal setting.
● My Color Control: Pink/Green/Blue/Reset
This setting can be adjusted to suit your personal preferences.
Select the Pink, Green or Blue by pressing the ▲ or ▼ button, then press the ENTER button.
Press the ◄ or ► button until you reach the optimal setting.
Reset: The previously adjusted colors will be reset to the factory defaults.
● Edge Enhancement: Off/On
You can emphasize object boundaries.
● xvYCC: Off/On
Setting the xvYCC mode to On increases detail and color space when watching movies from an external device (ie. DVD player)
connected to the HDMI or Component IN jacks. You must set the Picture Mode to Movie to enjoy this feature.
Changing the Screen Size
You can select the picture size which best corresponds to your viewing requirements.
1 Press the MENU button.
Press the ENTER button to select Picture.
Press the ▲ or ▼ button to select Size, then press the ENTER button.
Color Tone : Cool1
Detail Settings
Picture
Size : 16:9
Digital NR : Auto
Active Color : On
DNIe : On
Color Gamut
Position
Picture Reset
: Wide
2 Press the ▲ or ▼ button to select the screen format you want, then press the ENTER
button.
Press the EXIT button to exit.
16:9: Sets the picture to 16:9 wide mode.
Zoom1: Magnifies the size of the picture on the screen.
Zoom2: Expands the Zoom1 format picture.
Wide Fit : Enlarges the aspect ratio of the picture to fit the entire screen.
4:3 : Sets the picture to 4:3 normal mode.
Just Scan : Use this function to see the full image without cutting off the picture
when DTV or HDMI 1080i/1080p signals are input.
Press the P.SIZE button on the remote control to change the picture size.
16:9
Sets the picture to 16:9 wide mode.
Zoom1
The screen size when Wide screen
is vertically enlarged.
Size
16:9
Zoom1
Zoom2
Wide Fit
4:3
Just Scan
Move
Zoom2
The screen size when the Zoom1
screen is vertically enlarged.
ReturnEnter
Just Scan
Wide Fit
Enlarges the aspect ratio of the
picture to fit the entire screen.
4:3
Sets the picture to 4:3 normal mode.
Just Scan
Use this function to see the full
image without cutting off the picture
when DTV or HDMI 1080i/1080p
signals are input.
➢
● Only 16:9 and 4:3 are available in DTV, Component (720p, 1080i) and HDMI (720p, 1080i) modes.
● In COMPONENT(720p, 1080i) or HDMI(720p, 1080i) mode, 16:9, 4:3 and Wide Fit can be selected.
● You can select the 16:9, 4:3, Wide Fit and Just Scan screen sizes in the Component (1080i, 1080p), HDMI (1080i, 1080p),
or DTV (1080i, 1080p) mode.
● In Zoom1, Zoom2 and Wide Fit modes, you can move the picture on the screen by pressing the ▲ or ▼ button.
● Each adjusted setting will be stored separately according to its input mode.
● When watching an HD(High Definition 720p,1080i,1080p) signal, you can use Wide Fit.
Wide Fit sets the optimum picture format by expanding it both horizontally and vertically.
For example, you can reset the picture in 4:3 format to 16:9. Wide Fit does not support all external devices (DVD, VCR
etc.).
English - 30
Loading...