Samsung HLT5055WX-XAA User Manual
DLP TV
Owner’s Instructions
HL-T5055W
HL-T5655W
Register your product at www.samsung.com/global/register
Record your Model and Serial number here for future reference.
▪ Model _______________ ▪ Serial No. _______________
A Guide to Digital TV
• What is Digital Television?
Digital television (DTV) is a new way of transmitting high quality video and audio to your TV set. Using DTV, broadcasters can transmit
high definition TV (HDTV) images, Dolby digital surround audio, and new services such as multicasting (transmitting more than one
program on the same TV channel) and datacasting. Several of these services can be combined into a single digital broadcast.
Digital Television Services
• Digital Picture Quality
DTV programs are transmitted in two different formats. The first is Standard Definition Television (SDTV) and the second is High Definition
Television (HDTV).
• SDTV program formats include 480-line interlaced (480i) and 480-line progressive (480p) video. 480i programs are essentially a digital
version of our current analog TV programs, while the 480p format offers improved image detail over 480i. Some 480p programs are
broadcast in widescreen and are comparable to progressive-scan DVD movies in image quality.
• HDTV program formats include 1080-line interlaced (1080i) and 720-line progressive (720p). Both HDTV formats are always broadcast
in widescreen, and offer much higher picture quality than SDTV.
• Dolby Surround Sound
With DTV, you can listen to a variety of Dolby digital audio formats from Dolby Surround 2.0 to Dolby Digital 5.1 surround, using your
home audio system. Many HDTV programs are now broadcast with DD 5.1 soundtracks.
© 2007 Samsung Electronics Co., Ltd. All rights reserved.
English - 2
English - 3
Q&A
1. Is the antenna I use for existing TV reception good enough for DTV?
Over-the-air (OTA) digital TV broadcasting uses the same channels as analog TV and works well with many existing TV antennas.
However, DTV broadcast channel assignments are different than analog channels. You should find out whether your local DTV
broadcasts are on VHF (channels 2-13) or UHF (channels 14-69) to see if you need a different antenna.
If your DTV channels are on UHF and you already get good UHF reception, your present antenna may work fine. The same holds true for
VHF DTV reception. Note that in some markets, both VHF and UHF channels are used for DTV broadcasts.
You can find out the latest DTV channel assignments for your area by browsing selected Internet web sites such as www.titantv.com,
www.10000watts.com, and www.fcc.gov.
2. How difficult is it to receive DTV signals indoors?
This depends on whether your local DTV stations are running full power or not and how close your location is to the transmission tower.
DTV receivers do not require as much signal as analog TV receivers to produce high-quality images and sound.
Once the DTV signal level exceeds a certain threshold at the receiver, the digital video and audio data is decoded at the same quality it
was originally encoded for broadcast.
This is a big advantage for DTV over analog TV - there is no noise, ghosting, static, or scratchy audio.
3. How can I connect an antenna in my townhouse, co-operative apartment, condominium,
or apartment?
The Federal Communications Commission’s OTARD Rule (part of the Telecommunications Act of 1996) allows residents of
condominiums, townhouse, or members of neighborhood associations to put up outside antennas for reception of broadcast TV signals
as long as those antennas are not located in common areas and are no more than 12’ in height.
Residents of rental units (apartments, etc.) are not covered by the OTARD rules and will have to use indoor antennas to receive DTV
broadcasts. It is possible that the landlord of an apartment complex can provide broadcast DTV signals via a master TV antenna system
to each apartment.
4. Can I connect my DTV set-top receiver to my cable TV service?
Cable TV systems use a different method for transmitting digital TV programs that is currently incompatible with broadcast DTV set-top
receivers. So you will still need to use an outdoor or indoor antenna to receive OTA broadcast DTV programs.
The good news is that you won’t have to pay a monthly or per-program charge to watch OTA DTV and HDTV programs. They’re free,
unlike subscription satellite TV or premium cable TV. All you need is an antenna and a DTV set-top receiver to enjoy clear, sharp
widescreen images and high-quality audio.
Contents
GENERAL INFORMATION
■ Viewing Position
■ List of Features
■ Checking Parts
■ Viewing the Control Panel
■
Viewing the Connection Panel ......................................8
■
Remote Control .............................................................9
■
Installing Batteries in the Remote Control ..................10
CONNECTIONS
■
Connecting VHF and UHF Antennas ..........................10
■
Connecting Cable TV .................................................. 11
■
Connecting a VCR ......................................................12
■
Connecting a Camcorder ............................................13
■
Connecting a DVD Player/Set-Top Box ......................13
■
Connecting a DVD Player/Set-Top Box via HDMI ......13
■
Connecting a DVD Player/Set-Top Box via DVI ..........14
■
Connecting a Digital Audio System .............................14
■
Connecting an Amplifier/DVD Home Theater .............15
■
Connecting a PC .........................................................15
OPERATION
■
Turning the TV On and Off ..........................................16
■
Plug & Play Feature ....................................................16
■
Changing Channels ....................................................17
■
Adjusting the Volume ..................................................18
■
Viewing the Display ....................................................18
■
Viewing the Menus .....................................................19
■
Memorizing the Channels ...........................................19
■
Setting Up Your Remote Control .................................21
■
To Select the Source ...................................................26
■
To Edit the Input Source Name ...................................26
PICTURE CONTROL
■
Using Automatic Picture Settings ................................27
■ Making Detailed Picture Settings
■
Changing the Screen Size ..........................................29
■
Digital Noise Reduction ..............................................30
■
DNIe (Digital Natural Image engine) ...........................30
■ Setting the Color Gamut
■
Selecting the Film Mode .............................................31
■
Setting the Blue Screen Mode ....................................32
■ Setting the HDMI Black Level
■
Freezing the Picture ....................................................32
.........................................................5
..........................................................5
...........................................................6
..........................................
..........................28
.........................................31
................................32
CHANNEL CONTROL
■
Clearing Scrambled Channels - Digital .......................37
■
Adding and Erasing Channels ....................................37
■
Setting Your Favorite Channels ..................................38
■
6
Viewing the Channel Lists ..........................................39
■
Setting the Default Channel List Mode .......................40
■
Labeling Channels - Analog ........................................40
■
Fine Tuning Analog Channels - Analog .......................41
■
Checking the Digital-Signal Strength - Digital .............41
■
LNA (Low Noise Amplifier) ..........................................42
PC DISPLAY
■
Using Your TV as a Computer (PC) Display ...............42
■
Display Modes ............................................................42
■
Setting up the TV with your PC ...................................43
■ Changing the Picture Size (PC Mode)
■ Setting the Home Theater PC
FUNCTION DESCRIPTION
■
Selecting a Menu Language .......................................46
■
Setting the Time ..........................................................46
■
Using the Game Mode ................................................48
■
Using the V-Chip .........................................................49
■
Viewing Closed Captions
(On-Screen Text Messages) - Analog .........................
■
Viewing Closed Captions
(On-Screen Text Messages) - Digital ..........................
■
Menu Transparency Level ..........................................54
■ Adjusting the Melody Sound
■
Setting the Function Help ...........................................54
■ Upgrading the Software
APPENDIX
■
Troubleshooting ..........................................................56
■
Replacing the Lamp ....................................................57
■
Cleaning and Maintaining Your TV .............................58
■
Using Your TV in Another Country ..............................58
■
Specifications ..............................................................59
...............................45
..................................54
..........................................55
.................45
52
53
SOUND CONTROL
■
Using Automatic Sound Settings ................................33
■
Customizing the Sound ...............................................33
■
Setting up DNSe (Digital Natural Sound engine) ........34
■
Choosing a Multi-Channel Sound (MTS) Track - Digital
■
Choosing a Multi-Channel Sound (MTS) Track - Analog
■
Automatic Volume Control ..........................................35
■
Selecting the Internal Mute .........................................36
.......34
......35
English - 4
Press
Symbols
☛ ➢
Important
Note
One-Touch
Button
English - 5
General Information
Viewing Position
To optimize your viewing comfort, please follow the guidelines below for viewing distance.
If viewing for an extended period of time, sit as far back from the screen as possible.
➢
When installing the product, make sure to keep it away
from the wall (more than 10cm / 4inches) for ventilation
purposes.
Poor ventilation may cause an increase in the internal
temperature of the product, resulting in a shortened
component life and degraded performance.
List of Features
Your TV was designed and engineered using the latest technology. It is a full-featured, high-performance unit that exceeds
industry standards. In addition, it has these special features:
• Easy-to-operate remote control
• Easy-to-use on-screen menu system you can access from front panel or remote control
• Automatic timer to turn the TV on and off at any time you choose
• Adjustable picture and sound settings and the ability to memorize your favorite settings
• Automatic channel tuning for up to 181 channels
• A special filter to reduce or eliminate reception problems
• Fine tuning control for the sharpest picture possible
• A built-in multi-channel sound decoder for stereo and bilingual listening
• Built-in, dual channel speakers
• A special sleep timer
• Widescreen TV with adjustable image size
• Life-like clear images provided by DNle technology
• Color Weakness Enhancement Feature
• Digital Input jack
• Digital Audio Output (OPTICAL) jack
• Theater Game Mode
Checking Parts
Owner’s Instructions Remote Control
(BP59-00123A)/
AAA Batteries
Warranty Card/
Registration Card/
Safety Guide Manual/
Quick Guide Manual
Sold Separately
Replacement Lamp
(BP96-01472A)
For purchasing a replacement lamp,
ask at a nearby service center.
• Use authorized lamps only.
The company cannot guarantee
the quality of the product if an
unauthorized lamp is used.
S-Video Cable Antenna Cable
D-Sub Cable PC Audio Cable HDMI Cable HDMI/DVI Cable Optical Cable
3.5 mm Stereo
mini-plug/2RCA
Cable
Component Cables
Viewing the Control Panel
Buttons on the Lower Part of the Panel
The buttons on the lower panel control your TV’s basic features, including the on-screen menu.
To use the more advanced features, you must use the remote control.
Power Cord
(3903-000144)
Audio Cables Video Cables
➢
The product color and shape may vary depending on the model.
English - 6
Continued...
English - 7
1
POWER
Press to turn the TV on and off.
2
Remote Control Sensor
Aim the remote control towards this spot on the TV.
3
Indicator Lights
Blinks and turns off when the power is on and lights up in
stand-by mode.
4
SOURCE
Toggles between all the available input sources
(TV, AV1, AV2, AV3, S-Video1, S-Video2, S-Video3
6
+ VOL –
Press to increase or decrease the volume.
In the on-screen menu, use the + VOL – buttons as you
would use the ◄ and ► buttons on the remote control.
7
CH
Press to change channels.
In the on-screen menu, use the CH buttons as you
would use the ▲ and ▼ buttons on the remote control.
8
(ENTER)
Press to confirm a selection.
Component1, Component2, PC, HDMI1/DVI, or HDMI2).
5
MENU
Press to see an on-screen menu of your TV’s features.
Indicator Light Key
( : On, : Blinking, : Off)
STAND BY/TEMP
➢
◆ It takes about 30 seconds for the TV to warm up, so normal brightness may not appear immediately.
◆ The TV has a fan to keep the inside lamp from overheating. You’ll occasionally hear it working.
◆ You can use the channel selection buttons to switch on the TV when it is in standby mode depending on the model.
◆ When using the on-screen menu the volume adjustment and channel selection buttons have the same function as the ▲/▼/◄/►
buttons on the remote control.
◆ If the remote control no longer works or you have lost it, you can use controls on the panel of the TV.
TIMER LAMP Indication
Standby state.
The picture will automatically appear in about 15 seconds.
Auto Timer ON/OFF has been set and the set will automatically be turned on in about 15 seconds.
A cooling fan inside the set is not operating normally.
Lamp cover on the rear of the set is not properly shut.
Check if the ventilation hole on the rear of the set is blocked, because if the inner temperature is
too high, the power will shut off.
Lamp may be defective. Please contact a certified technician.
Viewing the Connection Panel
Rear Panel Jacks
Use the rear panel jacks to connect A/V components that will be connected continuously, such as VCR or DVD players.
For more information on connecting equipment, see pages 12-15.
➢
The product color and shape may vary depending on the model.
1
ANT 1 IN(CABLE)/ANT 2 IN(AIR)
75Ω Coaxial connector for Air/Cable Network.
2
SERVICE
This jack is for service only.
3
DIGITAL AUDIO OUT (OPTICAL)
Connect to a Digital Audio component.
4
DVI IN (AUDIO-L/R)
Connect to the DVI audio output jack of an external device.
5
S-VIDEO (AV IN 1, 2)
Video input for external devices with an
S-Video output, such as a Camcorder or VCR.
6
VIDEO/AUDIO-L/R (AV IN 1, 2)
Video input for external devices, such as a Camcorder or
VCR.
7
VIDEO/AUDIO OUT (L/R)
Video/Audio outputs for external devices.
Video output is not avaiable RF(Digital)/Component/PC/HDMI.
8
COMPONENT IN 1, 2
Video (Y/PB/PR) and audio (L-AUDIO-R) Component inputs.
9
PC IN
Connect to the video output jack on your PC.
0
PC AUDIO IN
Connect to the audio output jack on your PC.
!
HDMI IN 2
Connect to the HDMI jack of a device with HDMI output.
(Not compatible with PC)
@
HDMI 1/DVI IN
Connect to the HDMI jack of a device with HDMI output.
This input can also be used as a DVI connection with separate
analog audio inputs. An optional HDMI/DVI cable will be
necessary to make this connection.
When using an optional HDMI/DVI adapter, the DVI analog
audio inputs on your TV allow you to receive left and right
audio from your DVI device.
#
SERVICE 2
This jack is for software upgrade.
$
POWER IN
Connect the supplied power cord.
Side Panel Jacks
Use the right side panel jacks to connect a component that is used only occasionally (a camcorder or video game, for example).
The product color and shape may vary depending on the model.
1
S-VIDEO
Connect an S-Video signal from an S-VHS VCR or DVD player.
2
VIDEO
Connect the video signal from a camcorder or video game.
3
AUDIO (L/R)
Connect the audio signal from a camcorder or video game.
English - 8
English - 9
Remote Control
You can use the remote control up to a distance of about 23 feet from the TV. When using the remote, always point it directly at
the TV. You can also use your remote control to operate your VCR, Cable box, DVD Player, or Set-Top Box.
1
POWER
Turns the TV on and off.
2
Numeric Buttons
Press to directly select a channel.
3
–
Press to select additional channels
being broadcast by the same station.
For example, to select channel “54-3”,
press “54”, then press “–” and “3”.
4
CH LIST
Used to display Channel Lists on the
screen.
5
ANTENNA
Press to select “Air” or “Cable”.
6
VOL +, VOL –
Press to increase or decrease the
volume.
7
MUTE
Press to temporarily cut off the sound.
8
MENU
Displays the main on-screen menu.
9
RETURN
Returns to the previous menu.
0
S.MODE
Press to select the sound mode.
!
P.MODE
Press to select the picture mode.
@
SLEEP
Press to select a preset time interval
for automatic shut off.
#
GAME
Press to select various Game settings.
$
MTS
Press to choose Stereo, Mono or
Separate Audio Program (SAP
broadcast).
%
SET
Sets the remote to control your TV,
VCR, Cable, DVD, or Set-Top Box.
^
TV, DVD, STB, CABLE, VCR
Press to operate your TV, DVD, STB,
CABLE (box), or VCR.
&
SOURCE
Press to display all of the available
video sources.
*
Press to backlight the VOL, CH, and
the active source button (TV, DVD,
CABLE, STB, VCR) on the remote
control.
(
PRE-CH
Tunes to the previous channel.
)
FAV.CH
Press to switch to your favorite
channels.
a
HDMI
Selects the HDMI mode directly.
b
VCR/DVD Functions
- Rewind
- Stop
- Play/Pause
- Fast Forward
c
CH , CH
Press to change channels.
d
EXIT
Press to exit from the menu.
e
UP▲/DOWN▼/LEFT◄/RIGHT►/
ENTER
Use to select on-screen menu items
and change menu values.
f
INFO
Press to display information on the TV
screen.
g
CAPTION
Controls the caption decoder.
h
STILL
Press to stop the action during a
particular scene.
Press again to resume normal video.
i
Color buttons
Press to add or delete channels and to
store channels to the favorite channel
list in the “Channel List” menu.
(Refer to pages 37~39)
j
P.SIZE
Press to change the screen size.
k
ADD/DEL
Use to store and delete channels to/
from memory.
l
DNSe
DNSe enhances the sound quality,
automatically controls output, and
prevents sound distortion.
Press this button to set it On or Off.
(Refer to page 34)
m
RESET
When your remote control does not
work, change the batteries and press
the RESET button for 2-3 seconds
before use.
➢
This is a special remote control for the visually impaired person, and has Braille
points on the POWER, Channel, Volume, STOP, and PLAY/PAUSE buttons.
➢
The performance of the remote control may be affected by bright light.
Installing Batteries in the Remote Control
1 Lift the cover at the back of the remote control upward as shown in the figure.
2 Install two AAA size batteries.
➢
Make sure to match the “+” and “–” ends of the batteries with the diagram inside the
compartment.
➢
Do not mix battery types, i.e. alkaline and manganese.
3 Close the cover as shown in the figure.
➢
Remove the batteries and store them in a cool and dry place if you won’t be using the remote
control for a long time. The remote control can be used up to about 23 feet from the TV.
(Assuming typical TV usage, the batteries last for about one year.)
➢
If the remote control doesn’t work, check the following
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power cut, or is the power cord unplugged?
5. Is there a special fluorescent light or a neon sign nearby?
Connecting VHF and UHF Antennas
If your antenna has a set of leads that look like this, see “Antennas with 300 Ω Flat Twin
Leads” below.
If your antenna has one lead that looks like this, see “Antennas with 75 Ω Round Leads”.
If you have two antennas, see “Separate VHF and UHF Antennas”.
Antennas with 300 Ω Flat Twin Leads
If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has 300 Ω
twin flat leads, follow the directions below.
1 Place the wires from the twin leads under the screws on a 300-75 Ω adapter (not supplied).
Use a screwdriver to tighten the screws.
2 Plug the adaptor into the ANT 1 IN(CABLE) or ANT 2 IN(AIR) terminal on the rear of the TV.
Antennas with 75 Ω Round Leads
1
Plug the antenna lead into the ANT 1 IN(CABLE) or ANT 2 IN(AIR) terminal on the
rear
of the TV.
Separate VHF and UHF Antennas
If you have two separate antennas for your TV (one VHF and one UHF), you must combine the
two antenna signals before connecting the antennas to the TV. This procedure requires an
optional combiner-adaptor (available at most electronics shops).
1 Connect both antenna leads to the combiner.
2 Plug the combiner into the ANT 1 IN(CABLE) or ANT 2 IN(AIR) terminal on the bottom of the rear
panel.
English - 10
English - 11
Connecting Cable TV
To connect to a cable TV system, follow the instructions below.
Cable without a Cable Box
1 Plug the incoming cable into the ANT 1 IN(CABLE) terminal on the rear of the TV.
➢
Because this TV is cable-ready, you do not need a cable box to view unscrambled cable
channels.
Connecting to a Cable Box that Descrambles All Channels
1 Find the cable that is connected to the ANT OUT terminal on your cable box.
➢
This terminal might be labeled “ANT OUT”, “VHF OUT” or simply, “OUT”.
2 Connect the other end of this cable to the ANT 1 IN(CABLE) terminal on the rear of the TV.
Connecting to a Cable Box that Descrambles Some Channels
If your cable box descrambles only some channels(such as premium channels), follow the instructions below. You will need a
two-way splitter, an RF (A/B) switch, and four lengths of Antenna cable. (These items are available at most electronics stores.)
1 Find and disconnect the cable that is connected
to the ANT IN terminal on your cable box.
This terminal might be labeled “ANT IN”, “VHF IN”
➢
or simply, “IN”.
ANT IN
ANT IN
ANT OUT
2 Connect this cable to a two-way splitter.
3 Connect an Antenna cable between an OUTPUT
terminal on the splitter and the IN terminal on the
cable box.
4 Connect an Antenna cable between the ANT OUT
terminal on the cable box and the B-IN terminal
on the RF (A/B) switch.
5 Connect another cable between the other OUT
terminal on the splitter and the A-IN terminal on
the RF (A/B) switch.
6 Connect the last Antenna cable between the OUT
terminal on the RF (A/B) switch and the ANT IN 1
(CABLE) terminal on the rear of the TV.
After you have made this connection, set the
A/B switch to the “A” position for normal viewing.
Set the A/B switch to the “B” position to view
scrambled channels. (When you set the A/B
switch to “B”, you will need to tune your TV to
the cable box’s output channel, which is usually
channel 3 or 4.)
Incoming
cable
Incoming
cable
Incoming
Incoming
cable
cable
Splitter
Splitter
Splitter
Incoming
cable
Splitter
Cable Box
Cable Box
Cable Box
Splitter
RF (A/B)
Switch
Cable Box
RF (A/B)
Switch
RF (A/B)
Switch
TV Rear Panel
Connecting a VCR
Video Connection
These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the
instructions on pages 10~11). Skip step 1 if you have not yet connected to an antenna or a cable system.
1 Unplug the cable or antenna from the
rear of the TV
2 Connect the cable or antenna to the
ANT IN terminal on the back of the
VCR.
3 Connect an Antenna Cable between
the ANT OUT terminal on the VCR
and the ANT 1 IN(CABLE) or ANT 2
IN(AIR) terminal on the TV.
4 Connect a Video Cable between the
VIDEO OUT jack on the VCR and
the AV IN 1 [VIDEO] (or AV
IN 2 [VIDEO]) jack on the TV.
5 Connect Audio Cables between the
AUDIO OUT jacks on the VCR and
the AV IN 1 [L-AUDIO-R] (or AV
IN 2 L-AUDIO-R) jacks on the TV.
➢
If you have a “mono” (non-stereo)
VCR, use a Y-connector (not
supplied) to hook up to the right
and left audio input jacks of the TV.
If your VCR is stereo, you must
connect two cables.
VCR
2
➢
Each VCR has a different panel configuration.
➢
When connecting a VCR, match the color of the connection terminal to the cable.
Audio Cable(Not supplied)5
Video Cable(Not supplied)4
Antenna cable(Not supplied)3
TV Rear Panel
S-Video Connection
Your Samsung TV can be connected to the S-Video jack of a VCR.
(This connection delivers a better picture when compared to the regular Video connection above.)
1 To begin, follow steps 1–3 in the
previous section to connect the
antenna or cable to your VCR and
your TV.
2 Connect an S-Video Cable between
the S-VIDEO OUT jack on the VCR
and the AV IN 1 [S-VIDEO] (or AV
IN 2 [S-VIDEO]) jack on the TV.
3 Connect Audio Cables between the
AUDIO OUT jacks on the VCR and
the AV IN 1 [L-AUDIO-R] (or AV IN 2
[L-AUDIO-R]) jacks on the TV.
➢
Each S-VHS VCR has a different panel configuration.
➢
When connecting a VCR, match the color of the connection terminal to the cable.
➢
Some games may be displayed with a cut off picture when the TV is connected to a game player.
VCR
S-Video Cable(Not supplied)4
Antenna cable(Not supplied)3
Audio Cable
5
(Not supplied)
TV Rear Panel
English - 12
English - 13
Connecting a Camcorder
The side panel jacks on your TV make it easy to connect a camcorder to your TV.
They allow you to view the camcorder tapes without using a VCR.
1 Connect a Video Cable or S-Video
Cable between the AV IN 3 [VIDEO]
or [S-Video] jack on the TV and the
VIDEO OUT jack on the camcorder.
2 Connect Audio Cables between the
AV IN 3 [L-AUDIO-R] jacks on the
Camcorder
S-Video Cable(Not supplied)
1
or
1
Video Cable(Not supplied)
TV and the AUDIO OUT jacks on the
camcorder.
Audio Cable(Not supplied)
2
➢
Each Camcorder has a different panel configuration.
➢
When connecting a Camcorder, match the color of the connection terminal to the cable.
Connecting a DVD Player/Set-Top Box
The rear panel jacks on your TV make it easy to connect a DVD Player/Set-Top Box.
1 Connect Component Cables
between the COMPONENT IN 1
[Y, PB, PR] (or COMPONENT IN 2
[Y, PB, PR]) jacks on the TV and the
COMPONENT OUT [Y, PB, PR] jacks
on the DVD Player/Set-Top Box.
2 Connect Audio Cables between the
COMPONENT IN 1 [L-AUDIO-R] (or
COMPONENT IN 2 [L-AUDIO-R])
jacks on the TV and the AUDIO OUT
jacks on the DVD Player/
Set-Top Box.
DVD Player/Set-Top Box
2
Audio Cable(Not supplied)
TV Side Panel
TV Rear Panel
Component Cable(Not supplied)
1
➢
Component video separates the video into Y (Luminance (brightness)), PB (Blue) and PR (Red) for enhanced video quality.
Be sure to match the component video and audio connections
.
For example, if connecting the video cable to COMPONENT IN 1, connect the audio cable to COMPONENT IN 1 also.
➢
Each DVD Player/Set-Top box has a different panel configuration.
➢
When connecting a DVD Player/Set-Top box, match the color of the connection terminal to the cable.
Connecting a DVD Player/Set-Top Box via HDMI
This connection can only be made if there is an HDMI Output jack on the external device.
This connection will provide the highest quality picture.
1.
Connect an HDMI Cable between the
HDMI IN 2
on the TV and the HDMI
OUT on the DVD Player/
Set-Top Box.
What is HDMI?
● HDMI, or high-definition multimedia interface, is an interface that enables the transmission of digital audio and video signals using a
single cable.
● “Multimedia interface” is a more accurate name for it especially because it allows multiple channels of digital audio (5.1 channels).
The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP (High Bandwidth Digital Copy
Protection) coding feature installed, and supports multi-channel digital audio.
➢
Each DVD Player/Set-Top box has a different panel configuration.
➢
When connecting a DVD Player/Set-Top box, match the color of the connection terminal to the cable.
➢
When connecting via HDMI, you do not need to connect Audio Cables. You only need to connect Audio cables when connecting via
HDMI/DVI.
DVD Player / Set-Top Box
1
TV Rear Panel
HDMI Cable (Not supplied)
Connecting a DVD Player/Set-Top Box via DVI
This connection can only be made if there is a DVI Output jack on the external device.
1 Connect a HDMI/DVI Cable or
DVI-HDMI Adapter between the
HDMI 1/DVI IN jack on the TV and
the DVI jack on the DVD Player/
Set-Top Box.
2 Connect Audio Cables between the
DVI IN [L-AUDIO-R] jack on the TV
and the AUDIO OUT jacks on the
DVD Player/Set-Top Box.
➢
Each DVD Player/Set-Top box has a different panel configuration.
➢
When connecting a DVD Player/Set-Top box, match the color of the connection terminal to the cable.
➢
When using an HDMI/DVI cable connection, you must connect to the HDMI 1/DVI IN terminal on the TV.
DVD Player/Set-Top Box
2
Audio Cable(Not supplied)
HDMI/DVI Cable(Not supplied)
1
TV Rear Panel
Connecting a Digital Audio System
The rear panel jacks on your TV make it easy to connect a Digital Audio System to your TV.
Each Digital Audio System has a different panel configuration.
➢
1 Connect an Optical Cable between
the DIGITAL AUDIO OUT (OPTICAL)
jack on the TV and the Digital Audio
Input jack on the Digital Audio
System.
When a Digital Audio System is
connected to the DIGITAL AUDIO
OUT (OPTICAL) terminal: Decrease
the gain (volume) of the TV, and
adjust the volume level with the
system’s volume control.
5.1CH audio is possible when the TV
➢
is connected to an external device
supporting 5.1CH.
What is OPTICAL?
Converts the electric signal into an optical light signal, and transmits it through glass fibers. S/PDIF is a transmission system of digital
audio in the form of a light wave that uses a glass conductor.
Digital Audio System
1
Optical Cable (Not supplied)
TV Rear Panel
English - 14
English - 15
Connecting an Amplifier/DVD Home Theater
1 Connect Audio Cables between the
AUDIO OUT [L-AUDIO-R] on the TV
and AUDIO IN [L-AUDIO-R] on the
Amplifier/DVD Home Theater.
When an audio amplifier is
connected to the “AUDIO OUT
[L-AUDIO-R ]” terminals: Decrease
the gain (volume) of the TV, and
adjust the volume level with the
Amplifier’s volume control.
➢
Each Amplifier/DVD Home Theater has a different panel configuration.
➢
When connecting an Amplifier/DVD Home Theater, match the color of the connection terminal to the cable.
AV OUT L-AUDIO-R RF (Digital/Analog), AV, S-Video, Component, HDMI Sound is output
DIGITAL AUDIO OUT (OPTICAL)
If you want to play movies by connecting DVD Player or Set-Top Box to the COMPONENT IN jacks on the TV,
➢
connect the Optical OUT jack on the DVD Player or Set-Top Box to an Amplifier or DVD Home Theater.
Amplifier/
DVD Home Theater
1
Audio Cable (Not supplied)
RF (Digital/Analog), AV, S-Video, Component
Sound is output
HDMI Sound is not output
TV Rear Panel
Connecting a PC
Using the D-Sub Cable
1 Connect a D-Sub Cable between the
PC IN [PC] jack on the TV and the
PC output jack on your computer.
2 Connect a PC Audio Cable between
the PC IN [AUDIO] jack on the TV
and the Audio Out jack of the sound
card on your computer.
Using the HDMI/DVI Cable
1 Connect a HDMI/DVI Cable between
the HDMI1/DVI jack on the TV and
the PC output jack on your computer.
2 Connect a 3.5 mm Stereo mini-plug/
2RCA Cable between the DVI IN jack
on the TV and the Audio Out jack of
the sound card on your computer.
Using the D-Sub Cable
PC
2
PC Audio Cable (Not supplied)
1
D-Sub Cable (Not supplied)
Using the HDMI/DVI Cable
PC
3.5 mm Stereo mini-plug/2RCA Cable
2
(Not supplied)
1
HDMI/DVI Cable (Not supplied)
TV Rear Panel
TV Rear Panel
➢
Each PC has a different panel configuration.
➢
When connecting a PC, match the color of the connection terminal to the cable.
Operation
Turning the TV On and Off
Press the POWER button on the remote control.
You can also use the (Power) button on the front panel.
Plug & Play Feature
When the TV is initially powered on, basic settings proceed automatically and
subsequently:
1 Press the POWER button on the remote control.
The message Menu language, Shop Mode, Channels and Time will be set.
is displayed.
2 Press the ENTER button to enter the language.
Press the ▲ or ▼ button to select language, then press the ENTER button.
The message Select Home Mode when installing this TV at home. is automatically
displayed.
3 Press the ◄ or ► button to select Shop or Home, then press the ENTER button.
➢
The default selection is Home.
➢
We recommend setting the TV to Home mode for the best picture in your home
environment.
➢
Shop mode is only intended for use in retail environments.
➢
If the unit is accidentally set to Shop mode and you want to return to Dynamic (Home)
mode, press the Volume button and then hold down the MENU button for five seconds
on the TV panel.
4 Press the ▲ or ▼ button to memorize the channels of the selected connection.
Press the ENTER button to select Start.
➢
If the antenna is connected to ANT 1 IN(CABLE), select Cable and if it is connected to
ANT 2 IN(AIR), select Air.
➢
If both ANT 1 IN(CABLE) and ANT 2 IN(AIR) are connected, select the Air + Cable.
➢
In Cable mode, you can select the correct signal source among STD, HRC, and IRC by
pressing the ◄ button, then press the ▲ or ▼ button.
Press the ► button to select Start, then press the ENTER button.
Contact your local cable company to identify the type of cable system that exists in your
particular area.
5 The TV will begin memorizing all of the available channels. After all the available channels
are stored, the Auto program menu reappears.
Press the ENTER button when channel memorization is complete. Clock Mode menu is
automatically displayed.
➢
To stop the search before it has finished, press the ENTER button with stop selected.
6 Press the ENTER button.
Press the ▲ or ▼ button to select Manual for setting the current time manually, then press
the ENTER button. The message Enter the current date and time. is displayed.
➢
If you select Auto, Set to daylight saving time. is displayed, then go to step 9.
(If you want to set the time automatically, skip to step 9.)
7 Press the ◄ or ► button to move to Month, Day, Year, Hour, Minute, or am/pm.
Set the date and time you want by pressing the ▲ or ▼ button, then press the ENTER
button.
➢
You can set the Month, Day, Year, Hour, and Minute directly by pressing the number
buttons on the remote control.
8 The message Enjoy your watching. is displayed.
When you have finished, press the ENTER button.
➢
Even if the ENTER button is not pressed, the message will automatically disappear after
several seconds.
Menu language, Shop Mode,
Channels and Time will be set.
Start
Plug & Play
Plug & Play
Select the language of the OSD.
Language
Move
Select Home Mode when installing this TV at
home.
Shop Home
Move
Select the antennas to memorize.
Air
Cable
Air + Cable
Move
Selects a cable signal type for your
location.
Analog
STD
HRC
IRC
Digital
STD
HRC
IRC
Auto Program in Progress.
Set the Clock Mode.
Clock Mode
Move
Enter the current date and time.
Month Day Year
--
Hour Minute am/pm
--
Adjust
Enjoy your watching.
Plug & Play
Plug & Play
Plug & Play
Plug & Play
Move
Plug & Play
Stop
Plug & Play
Auto
Manual
Plug & Play
--
-- --
Move
English
Español
Français
Enter Skip
St art
St art
St art
Enter
--- -
Enter
St art
Air 16
15%
Skip
Skip
Skip
Skip
Skip
Skip
Enter
Enter
Enter
Enter
Continued...
English - 16
OK
English - 17
Setting the Clock Automatically
9 Press the ENTER button.
Press the ▲ or ▼ button to select Off or On, then the ENTER button.
The message Select the time zone where you are located. is automatically displayed.
Plug & Play
Set to daylight saving time.
DST
Off
On
10 Press the ▲ or ▼ button to highlight the time zone for your local area (and to move the
highlight to the appropriate time zone on the map of the United States).
Press the ENTER button.
If clock is not automatically set, see pages 46~47 to set the clock.
11 The message
Enjoy your watching. is displayed.
When you have finished, press the ENTER button.
➢
Even if the ENTER button is not pressed, the message will automatically disappear after
several seconds.
If you want to reset this feature...
1 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the ENTER button.
2 Press the ENTER button to select Plug & Play.
For further details on setting up options, refer to the top the pages 16~17.
➢
The Plug & Play feature is only available in the TV and DTV mode.
Plug & Play
OK
Move
Start
Enter
Enter
Setup
: Medium
Enter
Return
Move
Select the time zone where you are located.
Newfoundland
Atlantic
Eastern
Central
Mountain
Pacific
Alaska
Hawaii
Move
Enjoy your watching.
Plug & Play
Language : English
Time
Game Mode : Off
V-Chip
Caption
Menu Transparency
▼
More
Menu language, Shop Mode,
Channels and Time will be set.
Skip
Skip
►
►
►
►
►
►
►
Changing Channels
Using the Channel Buttons
Press the CH or CH button to change channels.
➢
When you press the CH or CH button, the TV changes channels in sequence.
You will see all the channels that the TV has memorized. (The TV must have memorized at
least three channels). You will not see channels that were either erased or not memorized.
See page 19 to memorize channels.
Using the Number Buttons
Use the number buttons to quickly tune to any channel.
Press the number buttons to go directly to a channel.
For example, to select channel 27, press 2, then 7.
The TV will change channels when you press the second number.
Continued...
Using the “-” Button
The - button is used to select stations that broadcast a digital signal.
For example, for Channel 7-1, press 7, then -, and then 1.
➢
HD indicates the TV is receiving a Digital High Definition signal.
SD indicates the TV is receiving a Standard Definition signal.
➢
For quick channel change, press the number buttons, then press the ENTER button.
Using the PRE-CH Button to select the Previous Channel
Press the PRE-CH button.
The TV will switch to the last channel viewed.
➢
To quickly switch between two channels that are far apart, tune to one channel, then use
the number button to select the second channel. Then use the PRE-CH button to quickly
alternate between them.
Adjusting the Volume
Press the VOL + or VOL – button to increase or decrease the volume.
Using the MUTE Button
At any time, you can cut off the sound using the MUTE button.
1 Press the MUTE button and the sound cuts off.
The word Mute will appear in the lower-left corner of the screen.
2 To turn mute off, press the MUTE button again, or simply press the VOL + or VOL – button.
Viewing the Display
The display identifies the current channel and the status of certain audio-video settings.
Press the INFO button on the remote control.
The TV will display the channel, the type of sound, and the status of certain picture and sound
settings.
Press the INFO button once more or wait approximately 10 seconds and it disappears
automatically.
English - 18
Air 28
Mono
Picture Mode : Dynamic
Sound Mode : Custom
MTS : Stereo
Caption : Off
V-Chip : Off
12 : 00 am
English - 19
Viewing the Menus
1 With the power on, press the MENU button.
The main menu appears on the screen. Its left side has five icons:
Picture, Sound, Channel, Setup, Input.
Source List : TV
Edit Name
Input
►
►
2 Use the ▲ or ▼ button to select one of the five icons.
Then press the ENTER button to access the icon’s sub-menu.
3 Press the EXIT button to exit.
➢
It takes about one minute until the on-screen menu disappears.
Move
Enter Exit
Memorizing the Channels
Your TV can memorize and store all of the available channels for both “off-air” (air) and cable channels. After the available
channels are memorized, use the CH and CH button to scan through the channels. This eliminates the need to change
channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source,
memorizing the channels (automatic) and adding or deleting channels (manual).
Selecting the Video Signal-source
Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the
TV(i.e. an air or a cable system).
1 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the ENTER button.
2 Press the ENTER button select Antenna.
Press the ▲ or ▼ button to select Air or Cable, then press the ENTER button.
Press the MENU button.
Antenna : Air
Auto Program
Clear Scrambled Channel
Channel List
Name
Fine Tune
Signal Strength
LNA : On
Antenna : Air
Auto Program
Clear Scrambled Channel
Channel List
Name
Fine Tune
Signal Strength
LNA : On
Move
Move
Channel
Enter
Channel
Enter
Air
Cable
Return
Return
►
►
►
►
►
►
►
►
Storing Channels in Memory (Automatic Method)
1 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the ENTER button.
2 Press the ▲ or ▼ button to select Auto Program, then press the ENTER button.
3 Press the ▲ or ▼ button to select the antenna connection, then press the ENTER button.
➢
Air : “Air” antenna signal.
Cable : “Cable” antenna signal.
Air+Cable : “Air” and “Cable” antenna signals.
➢
If the antenna is connected to ANT 1 IN(CABLE), select Cable and if it is connected to
ANT 2 IN(AIR), select Air.
➢
If both ANT 1 IN and ANT 2 IN are connected, select the Air + Cable.
➢
If you selected Air, then go to step 5.
Channel
Antenna : Air
Auto Program
Clear Scrambled Channel
Channel List
Name
Fine Tune
Signal Strength
LNA : On
Enter
Enter
St art
St art
St art
Return
Return
Move
Auto Program
Selects the antennas to memorize.
Air
Cable
Air + Cable
Move
Continued...
►
►
►
►
►
►
►
►
4 Press the ▲ or ▼ button to select Analog or Digital, then press the ENTER button.
You can select the correct signal source among STD, HRC and IRC by pressing the
▲ or ▼ button, then press the ENTER button.
To memorize the channels, press the ▲ or ▼ button to select Start, then press the
ENTER button.
➢
If you have Digital cable TV, select the signal source for both Analog and Digital.
➢
STD, HRC, and IRC identify various types of cable TV systems. Contact your local
cable company to identify the type of cable system that exists in your particular area.
At this point the signal source has been selected.
5 The TV begins memorizing all available stations.
When pressing the ENTER button during a storing process, the message Stop Auto
Program? will be displayed. Select Yes by pressing the ◄ or ► button.
Press the EXIT button to exit.
➢
The TV must be connected to an antenna/cable in order to receive digital TV signals.
Even if a particular channel is deleted from the memory, you can always tune to that
channel directly by using the number buttons on the remote control.
➢
• All available DTV and analog channels are automatically stored in memory.
• It takes approximately 3 to 10 minutes to memorize channels.
Auto Program
Selects a cable signal type for your location.
Analog
STD
HRC
IRC
Digital
STD
HRC
IRC
Auto Program
Auto Program in Progress.
Auto Program
Stop Auto Program?
Yes No
Move
Move
Enter
Stop
Enter
Enter
St art
Air 16
15%
15%
Return
Return
Return
English - 20
English - 21
Setting Up Your Remote Control
After your remote control has been properly set up, your remote control can operate in five different modes: TV, VCR, Cable,
DVD, or Set-Top Box. Pressing the corresponding button on the remote control allows you to switch between these modes,
and control whichever piece of equipment you choose.
➢
The remote control might not be compatible with all DVD Players, VCRs, Cable boxes, and Set-Top Boxes.
Setting Up the Remote to Operate Your VCR
1 Turn off your VCR.
2 Press the VCR button on your TV’s remote control.
3 Press the SET button on your TV’s remote control.
4 Using the number buttons on your remote control, enter three digits of the VCR code listed
on page 23 of this manual for your brand of VCR. Make sure you enter three digits of the
code, even if the first digit is a “0”. (If more than one code is listed, try the first one.)
5 Press the POWER button on the remote control. Your VCR should turn on if your remote
is set up correctly.
If your VCR does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other codes
listed for your brand of VCR. If no other codes are listed, try each VCR code, 000 through 080.
Note on Using Remote Control Modes: VCR
When your remote control is in VCR mode, the volume buttons still control your TV’s volume.
Setting Up the Remote to Operate Your Cable Box
1 Turn off your cable box.
2 Press the CABLE button on your TV’s remote control.
3 Press the SET button on your TV’s remote control.
4 Using the number buttons on your remote control, enter three digits of the cable box code
listed on page 24 of this manual for your brand of cable box. Make sure you enter three
digits of the code, even if the first digit is a “0”. (If more than one code is listed, try the first
one.)
5 Press the POWER button on the remote control.
Your cable box should turn on if your remote is set up correctly.
If your cable box does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other
codes listed for your brand of cable box. If no other codes are listed, try each code, 000 through
046.
Note on Using Remote Control Modes: Cable Box
When your remote control is in CABLE mode, the volume buttons still control your TV’s volume.
Continued...
Loading...