Samsung HL72A650C1FXZA User Manual [en, es]

Contact SAMSUNG WORLD-WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.

Comment contacter Samsung dans le monde Si vous avez des suggestions ou des questions concernant les produits Samsung, veuillez contacter le Service Consommateurs Samsung.

Country

CANADA 1-800-SAMSUNG (7267864) www.samsung.com/ca

U.S.A 1-800-SAMSUNG (7267864) www.samsung.com

Customer Care Center 

Web Site Address

Samsung Electronics Canada Inc., Customer Service 55 Standish Court Mississauga, Ontario L5R 4B2 Canada

Samsung Electronique Canada Inc., Service à la Clientèle 55 Standish Court Mississauga, Ontario L5R 4B2 Canada

Samsung Electronics America, Inc. 105 Challenger Road Ridgefield Park, NJ 07660-0511

DLP TV

user manual

BP68-00670A-01

imagine the possibilities

Thank you for purchasing this Samsung product. To receive more complete service, please

www.samsung.com/global/register

Model Serial No.

A Guide to Digital TV

● What is Digital Television?

Digital television (DTV) is a new way of transmitting high quality video and audio to your TV set. Using DTV, broadcasters can transmit high definition TV (HDTV) images, Dolby digital surround audio, and new services such as multicasting (transmitting more than one program on the same TV channel) and datacasting. Several of these services can be combined into a single digital broadcast.

Digital Television Services

● Digital Picture Quality

DTV programs are transmitted in two different formats. The first is Standard Definition Television (SDTV) and the second is High Definition Television (HDTV).

SDTV program formats include 480-line interlaced (480i) and 480-line progressive (480p) video. 480i programs are essentially

●

a digital version of our current analog TV programs, while the 480p format offers improved image detail over 480i. Some 480p programs are broadcast in widescreen and are comparable to progressive-scan DVD movies in image quality.

HDTV program formats include 1080-line interlaced (1080i) and 720-line progressive (720p). Both HDTV formats are always

●

broadcast in widescreen, and offer much higher picture quality than SDTV.

SAMSUNG ELECTRONICS NORTH AMERICAN LIMITED WARRANTY STATEMENT

Subject to the requirements, conditions, exclusions and limitations of the original Limited Warranty supplied with Samsung Electronics (SAMSUNG) products, and the requirements, conditions, exclusions and limitations contained herein, SAMSUNG will additionally provide Warranty Repair Service in the United States on SAMSUNG products purchased in Canada, and in Canada on SAMSUNG products purchased in the United States, for the warranty period originally specified, and to the Original Purchaser only. The above described warranty repairs must be performed by a SAMSUNG Authorized Service Center. Along with this Statement, the Original Limited Warranty Statement and a dated Bill of Sale as Proof of Purchase must be presented to the Service Center. Transportation to and from the Service Center is the responsibility of the purchaser. Conditions covered are limited only to manufacturing defects in material or workmanship, and only those encountered in normal use of the product. Excluded, but not limited to, are any originally specified provisions for, in-home or on-site services, minimum or maximum repair times, exchanges or replacements, accessories, options, upgrades, or consumables. For the location of a SAMSUNG Authorized Service Center, please call toll-free: In the United States : 1-800-SAMSUNG (1-800-726-7864) In Canada : 1-800-SAMSUNG

See the warranty card for more information on warranty terms.

➢

English - 2

English - 3

Q&A

1. Is the antenna I use for existing TV reception good enough for DTV?

Over-the-air (OTA) digital TV broadcasting uses the same channels as analog TV and works well with many existing TV antennas. However, DTV broadcast channel assignments are different than analog channels. You should find out whether your local DTV broadcasts are on VHF (channels 2-13) or UHF (channels 14-69) to see if you need a different antenna.

If your DTV channels are on UHF and you already get good UHF reception, your present antenna may work fine. The same holds

true for VHF DTV reception. Note that in some markets, both VHF and UHF channels are used for DTV broadcasts.

You can find out the latest DTV channel assignments for your area by browsing selected Internet web sites such as www.titantv.

com, www.10000watts.com, and www.fcc.gov.

2. How difficult is it to receive DTV signals indoors?

This depends on whether your local DTV stations are running full power or not and how close your location is to the transmission tower. DTV receivers do not require as much signal as analog TV receivers to produce high-quality images and sound.

Once the DTV signal level exceeds a certain threshold at the receiver, the digital video and audio data is decoded at the same

quality it was originally encoded for broadcast. This is a big advantage for DTV over analog TV - there is no noise, ghosting, static, or scratchy audio.

3. How can I connect an antenna in my townhouse, co-operative apartment, condominium, or apartment?

The Federal Communications Commission’s OTARD Rule (part of the Telecommunications Act of 1996) allows residents of condominiums, townhouse, or members of neighborhood associations to put up outside antennas for reception of broadcast TV signals as long as those antennas are not located in common areas and are no more than 12’ in height.

Residents of rental units (apartments, etc.) are not covered by the OTARD rules and will have to use indoor antennas to receive

DTV broadcasts. It is possible that the landlord of an apartment complex can provide broadcast DTV signals via a master TV antenna system to each apartment.

4. Can I connect my DTV set-top receiver to my cable TV service?

Cable TV systems use a different method for transmitting digital TV programs that is currently incompatible with broadcast DTV set-

top receivers. So you will still need to use an outdoor or indoor antenna to receive OTA broadcast DTV programs.

The good news is that you won’t have to pay a monthly or per-program charge to watch OTA DTV and HDTV programs. They’re

free, unlike subscription satellite TV or premium cable TV. All you need is an antenna and a DTV set-top receiver to enjoy clear, sharp widescreen images and high-quality audio.

Contents

General Information

■



Viewing Position ...................................................................... 5

English

■



List of Features ....................................................................... 5

■



Checking Parts ........................................................................ 6

■



Viewing the Control Panel ....................................................... 6

■



Viewing the Connection Panel ................................................8

■



Remote Control ....................................................................... 9

■



Installing Batteries in the Remote Control ............................. 10

Connections

■



Connecting VHF and UHF Antennas ....................................10

■



Connecting Cable TV .............................................................11

■



Connecting a DVD Player or Cable Box / Satellite receiver

(Set-Top Box) via HDMI ........................................................ 12

■



Connecting a DVD Player or Cable Box / Satellite receiver

(Set-Top Box) via DVI ...........................................................12

■



Connecting a DVD Player or Cable Box / Satellite receiver

(Set-Top Box) via Component cables ...................................13

■



Connecting a Camcorder ......................................................13

■



Connecting a VCR ................................................................ 14

■



Connecting a Digital Audio System ....................................... 15

■



Connecting an Amplier / DVD Home Theater ..................... 15

■



Connecting a PC ................................................................... 16

Operation

■



Turning the TV On and Off .................................................... 16

■



Plug & Play Feature ..............................................................17

■



Changing Channels .............................................................. 19

■



Adjusting the Volume ............................................................20

■



Viewing the Display ............................................................... 20

■



Viewing the Menus ................................................................ 20

■



Using the TOOLS Button ...................................................... 21

■



Memorizing the Channels ..................................................... 21

■



To Select the Source ............................................................. 23

■



To Edit the Input Source Name .............................................23

Picture Control

■



Changing the Picture Standard ............................................. 24

■



Customizing the Picture Settings ..........................................24

■



Adjusting the Detailed Settings .............................................25

■



Conguring Picture Options .................................................27

■



Using the 3D Function .......................................................... 32

■



Resetting the Picture Settings to the Factory Defaults ......... 33

Sound Control

■



Using Automatic Sound Settings ...........................................34

■



Customizing the Sound ......................................................... 34

■



Setting the TruSurround XT ..................................................35

■



Choosing Preferred Language .............................................. 36

■



Choosing a Multi-Channel Sound (MTS) Track - Analog ...... 36

■



Automatic Volume Control .................................................... 37

■



Setting the TV Speakers On/Off ............................................37

■



Resetting the Sound Settings to the Factory Defaults .......... 38

Channel Control

■



Managing Channels ..............................................................39

■



Clearing Scrambled Channels - Digital ................................. 45

■



Fine Tuning Analog Channels ...............................................45

■



Checking the Digital-Signal Strength .................................... 46

PC Display

■



Using Your TV as a Computer (PC) Display ......................... 47

■



Display Modes ...................................................................... 47

■



Setting up the TV with your PC ............................................. 48

Time Setting

■



Setting the Time .................................................................... 50

Function Description

■



Selecting a Menu Language ................................................. 54

■



Using the V-Chip ................................................................... 55

■



Viewing Closed Captions (On-Screen Text Messages) - Digital ....

■



Viewing Closed Captions (On-Screen Text Messages) - Analog

■



Adjusting the TV On/Off Melody Sound ................................65

■



Setting the Entertainment mode ........................................... 66

■



Upgrading the Software ........................................................ 67

WISELINK

■



Using the Photo List .............................................................. 70

■



Viewing a Photo or Slide Show ............................................. 75

■



Using the Music List .............................................................. 79

■



Playing a Music File ..............................................................83

■



Using the Setup Menu .......................................................... 85

About Anynet+

■



What is Anynet+? .................................................................. 86

■



Connecting Anynet+ Devices ................................................ 86

■



Setting Up Anynet

■



Scanning and Switching between Anynet+ Devices ............. 87

■



Recording .............................................................................. 88

■



Listening through a Receiver (Home theater) ....................... 89

■



Troubleshooting for Anynet

+ ............................................................... 87

+ ................................................. 89

Appendix

■



Troubleshooting .................................................................... 90

■



Replacing the Lamp ..............................................................91

■



Cleaning and Maintaining Your TV ........................................ 92

■



Using Your TV in Another Country ........................................92

■



Technical Specications ........................................................ 93

Symbols

☛ ➢

Press

Important

Note

One-Touch

Button

... 64

English - 4

English - 5

General Information

Viewing Position

To optimize your viewing comfort, please follow the guidelines below for viewing distance. If viewing for an extended period of time, sit as far back from the screen as possible.

< Top view> < Side view>

72˝ screen : At least 8.4 feet

➢

When installing the product, make sure to keep it away

from the wall (more than 10cm / 4inches) for ventilation purposes. Poor ventilation may cause an increase in the internal temperature of the product, resulting in a shortened component life and degraded performance.

72˝ screen : At least 8.4 feet

List of Features

Your TV is designed and engineered using the latest technology. It is a full-featured, high-performance unit that exceeds industry standards. In addition, it has these special features:

● Easy-to-operate remote control

● Dynamic menus and Navigating menus by using the menu map

● Easy-to-use on-screen menu system you can access from the side panel or remote control

● Automatic timer to turn the TV on and off at any time you choose

● Adjustable picture and sound settings and the ability to memorize your favorite settings

● Automatic channel tuning for up to 181 channels

● A special filter to reduce or eliminate reception problems

● Fine tuning control for the sharpest picture possible

● A built-in multi-channel sound decoder for stereo and bilingual listening

● Built-in, dual channel speakers

● A special sleep timer

● Widescreen TV with adjustable image size

● Life-like clear images provided by DNle technology

● Detailed settings mode to correspond with your color preference

● HDMI/DVI connection of your PC to this TV

● Digital Input jack

● Digital Audio Output (OPTICAL) jack

● Easy-to-use channel list menu.

● WISELINK enables you to view and play photo (JPEG) and audio files (MP3) through the TV’s WISELINK jack.

● AV network system (Anynet+) that enables you to easily control Samsung audio-video(AV) devices from this TV.

● 3D Effect Gaming Function

● Some users might observe small brightness variations in localized areas when very bright or dark signals are applied. These are

normal production variations and do not diminish the TVs viewing experience.

Checking Parts

Owner’s Instructions Remote Control

(BN59-00673A)/

AAA Batteries

Warranty Card/

Safety Guide Manual/

Quick Guide Manual

(Not available in all locations)

Power Cord

(3903-000144)

Sold Separately

S-Video Cable Video Cable Antenna Cable

D-Sub Cable PC Audio Cable HDMI/DVI Cable HDMI Cable

3.5 mm Stereo

mini-plug/ 2RCA Cable

Audio Cables Optical Cable

Component Cables

Viewing the Control Panel

Buttons on the Lower-Right Part of the Panel

The buttons on the lower-right panel control your TV’s basic features, including the on-screen menu. To use the more advanced features, you must use the remote control.

Cloth-Clean

Replacement Lamp

(BP96-01600A)

To purchase a replacement lamp, call 1-800-SAMSUNG.

• Use authorized lamps only. We cannot guarantee the quality of the product if an unauthorized lamp is used.

➢

The product color and shape may vary depending on the model.

English - 6

Continued...

English - 7

SOURCE

Toggles between all the available input sources (TV, AV1, AV2, S-Video, Component1, Component2, PC, HDMI1, HDMI2, HDMI3/DVI or USB).

Press to see an on-screen menu of your TV’s features.

+ VOL –

Press to increase or decrease the volume. In the on-screen menu, use the + VOL – buttons as

you would use the ◄ and ► buttons on the remote

(ENTER)

Press to confirm a selection.

Indicator Lights

Blinks and turns off when the power is on and lights up in stand-by mode.

POWER

Press to turn the TV on and off. Remote Control Sensor Aim the remote control towards this spot on the TV.

control.

Press to change channels. In the on-screen menu, use the CH buttons as

you would use the ▲ and ▼ buttons on the remote

control.

➢

● When using the on-screen menu, the volume adjustment and channel selection buttons have the same function as the ▲/▼/◄/► buttons on the remote control.

● If the remote control no longer works or you have lost it, you can use controls on the panel of the TV.

Indicator Light Key

( : On, : Blinking, : Off)

STAND BY/TEMP TIMER LAMP Indication

Standby state.

The picture will automatically appear in about 15 seconds.

Auto Timer ON/OFF has been set and the set will automatically be turned on in about 15 seconds.

A cooling fan inside the set is not operating normally.

Lamp cover on the side of the set is not properly shut. Check if the ventilation hole on the side of the set is blocked, because if the inner temperature is too

high, the power will shut off. Lamp may be defective. Please contact a certified technician.

➢

● It takes about 30 seconds for the TV to warm up, so normal brightness may not appear immediately.

● The TV has a fan to keep the inside Lamp from overheating. You’ll occasionally hear it working.

Viewing the Connection Panel

Rear Panel Jacks

Use the side panel jacks to connect A/V components that will be connected continuously, such as VCR or DVD players. For more information on connecting equipment, see pages 12~16.

➢

The product color and shape may vary depending on the model.

ANT IN

75Ω Coaxial connector for Air/Cable Network.

HDMI IN 1, HDMI IN 2

Connect to the HDMI jack of a device with HDMI output.

HDMI3/DVI IN

Connect to the HDMI jack of a device with HDMI output. This input can a lso be used as a DVI connecti on wit h

separate analog audio inputs. An optional HDMI/DVI cable will be necessary to make this connection.

When using an optional HDMI/DVI adapter, the DVI analog

audio inputs on your TV allow you to receive left and right audio from your DVI device.

DVI IN (AUDIO-L/R)

Connect to the DVI audio output jack of an external device.

DIGITAL AUDIO OUT (OPTICAL)

Connect to a Digital Audio component.

RS232C

Connector for service only

S-VIDEO

Video input for external devices with an S-Video output, such as a Camcorder or VCR.

VIDEO/AUDIO-L/R (AV IN 1, 2)

Video input for external devices, such as a Camcorder or

VCR.

3D SYNC OUT

Connect to 3D IR Emitter.

AUDIO OUT-L/R

Audio outputs for external devices.

COMPONENT IN 1, 2

Video (Y/PB/PR) and audio (L-AUDIO-R) component inputs.

POWER IN

Connect the supplied power cord.

PC AUDIO IN

Connect to the audio output jack on your PC.

PC IN

Connect to the video output jack on your PC.

Side Panel Jacks

Use the right side panel jacks to connect a component that is used only occasionally, such as a camcorder or video game.

AV IN 2

Video and audio inputs for external devices.

WISELINK

Connect an USB mass storage device to view photo files (JPEG) and play audio files

(MP3).

➢

The product color and shape may vary depending on the model.

English - 8

English - 9

Remote Control

You can use the remote control up to a distance of about 23 feet from the TV.

1 POWER

Turns the TV on and off.

2 TV

Selects the TV mode directly.

3 NUMERIC BUTTONS

Press to change the channel.

Press to select additional channels

(digital and analog) being broadcast by the same station. For example, to select channel “54-3”, press “54”, then press “ ” and “3”.

5 MUTE

Press to temporarily cut off the

sound.

VOL

Press to increase or decrease the

volume.

7 SOURCE

Press to display and select the

available video sources.

8 CH LIST

Used to display Channel Lists on the

screen.

9 TOOLS

Use to quickly select frequently used

functions.

0 UP▲/DOWN▼/LEFT◄/

RIGHT►/ENTER

Use to select on-screen menu items

and change menu values.

! INFO

Press to display information on the

TV screen.

@ COLOR BUTTONS

Use these button in the CH LIST and

W.LINK.

# CC

Controls the caption decoder.

$ E.MODE

Press to select the preset display

and sound modes for sports, cinema and games.

% Use these buttons in the DMA,

W.LINK and Anynet+ modes. (

: This remote can be used to control recording on Samsung recorders with the Anynet+ feature)

^ ON/OFF

Press to backlight the buttons on the

remote.

This function is convenient for using

at night or when the room is dark.

(Using the remote control with the

light button set to On will reduce the battery usage time.)

& PRE-CH

Tunes to the previous channel.

Press to change channels.

( MENU

Displays the main on-screen menu.

) W.LINK (WISELINK)

This function enables you to view

and play photo and music files from an external USB device. (Refer to pages 70 (Photo) and 79 (Music))

a RETURN

Returns to the previous menu.

b EXIT

Press to exit the menu.

c MTS

Press to choose stereo, mono or

Separate Audio Program (SAP broadcast).

d DMA (Digital Media Adapter)

Use this when connecting a

Samsung DMA device through an HDMI interface and switching to DMA mode.

For more information on the

operating procedures, refer to the user manual of the DMA.

This button is available when

➢

“Anynet+(HDMI-CEC)” is “On”. (see page 86)

e P.SIZE

Picture size selection.

f FAV.CH

Press to switch to your favorite

channels.

The performance of the remote control may be affected by bright light.

➢

Installing Batteries in the Remote Control

1 Lift the cover at the back of the remote control upward as shown in the figure. 2 Install two AAA size batteries.

➢

● Make sure to match the “+” and “–” ends of the batteries with the diagram inside the compartment.



● Do not mix battery types, i.e. alkaline and manganese.

3 Close the cover as shown in the figure.

➢

Remove the batteries and store them in a cool and dry place if you won’t be using the remote control for a long time. The remote control can be used up to about 23 feet from the TV. (Assuming

typical TV usage, the batteries last for about one year.)

➢

Using the remote control with the On/Off( ) light button set to On will reduce the battery usage time.

➢

 If the remote control doesn’t work! Check the following

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power cut, or is the power cord unplugged?

5. Is there a special fluorescent light or a neon sign nearby?

Connections

Connecting VHF and UHF Antennas

Ifyourantennahasasetofleadsthatlooklikethis,see“Antennaswith300ΩFlatTwin

Leads” below.

Ifyourantennahasoneleadthatlookslikethis,see“Antennaswith75ΩRoundLeads”. If you have two antennas, see “Separate VHF and UHF Antennas”.

Antennaswith300ΩFlatTwinLeads

Ifyouareusinganoff-airantenna(suchasaroofantennaor“rabbitears”)thathas300Ωtwinflatleads,followthe

directions below. 1 Place the wires from the twin leads under the screws on a 300-75 Ω adapter (not supplied).

Use a screwdriver to tighten the screws.

2 Plug the adaptor into the ANT IN terminal on the side of the TV.

Antennaswith75ΩRoundLeads

1 Plug the antenna lead into the ANT IN terminal on the side of the TV.

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before connecting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics shops).

1 Connect both antenna leads to the combiner.

2 Plug the combiner into the ANT IN terminal on the bottom of the side panel.

English - 10

English - 11

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

1 Plug the incoming cable into the ANT IN terminal on the side of the TV.

➢

Because this TV is cable-ready, you do not need a cable box to view unscrambled cable channels.

Connecting to a Cable Box that Descrambles All Channels

1 Find the cable that is connected to the ANT OUT terminal on your cable box.

➢

This terminal might be labeled “ANT OUT”, “VHF OUT” or simply, “OUT”.

2 Connect the other end of this cable to the ANT IN terminal on the side of the TV.

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-way splitter, an RF (A/B) switch, and four lengths of Antenna cable. (These items are available at most electronics stores.)

1 Find and disconnect the cable that is connected

to the ANT IN terminal on your cable box.

➢

This terminal might be labeled “ANT IN”, “VHF IN” or simply, “IN”.

ANT IN

ANT OUT

2 Connect this cable to a two-way splitter.

Incoming

cable

Splitter

3 Connect an Antenna cable between an

OUTPUT terminal on the splitter and the IN terminal on the cable box.

Incoming

cable

Splitter

Cable Box

4 Connect an Antenna cable between the ANT

OUT terminal on the cable box and the B–IN

terminal on the RF(A/B) switch.

Incoming

cable

Splitter

Cable Box

RF (A/B)

Switch

5 Connect another cable between the other OUT

terminal on the splitter and the A–IN terminal on

the RF (A/B) switch.

Incoming

cable

6 Connect the last Antenna cable between the

OUT terminal on the RF (A/B) switch and the

Splitter

Cable Box

TV Side

RF (A/B)

Switch

ANT IN terminal on the side of the TV.

Incoming

cable

Splitter

Cable Box

RF (A/B)

Switch

After you have made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the “B” position to view scrambled channels. (When you set the A/B switch to “B”, you will need to tune your TV to the cable box’s output channel, which is usually channel 3 or 4.)

Connecting a DVD Player or Cable Box / Satellite receiver (Set-Top Box) via HDMI

This connection can only be made if there is an HDMI Output jack on the external device. This connection will provide the highest quality picture.

1 Connect an HDMI Cable

between the HDMI IN (1, 2 or

3) on the TV and the HDMI jack on the DVD Player or Cable Box / Satellite receiver (Set-Top Box).

TV Rear Panel

DVD Player or Cable Box /

Satellite receiver (Set-Top Box)

or or

HDMI Cable (Not supplied)1

What is HDMI?

• HDMI, or high-definition multimedia interface, is an interface that enables the transmission of digital audio and video signals using a single cable.

• The difference between HDMI and DVI is that the HDMI device is smaller in size and has the HDCP (High Bandwidth Digital Copy Protection) coding feature installed.

Each DVD Player or Cable Box / Satellite receiver (Set-Top Box) has a different

➢

back panel configuration.

The TV may not output sound and pictures may be displayed with abnormal color

➢

when DVD Player or Cable Box / Satellite receivers supporting HDMI versions older than 1.3 are connected. When connecting an older HDMI cable and there is no sound, connect the HDMI cable to the HDMI3/DVI IN jack and the audio cables to the HDMI3/DVI IN [R-AUDIO-L] jacks on the back of the TV. If this happens, contact the company that provided the DVD Player or Cable Box / Satellite receiver to confirm the HDMI version, then request an upgrade.

HDMI cables that do not support HDMI version 1.3 may cause annoying flicker or

➢

no screen display.

Connecting a DVD Player or Cable Box / Satellite receiver (Set-Top Box) via DVI

This connection can only be made if there is a DVI Output jack on the external device.

1 Connect a HDMI/DVI Cable

or DVI-HDMI Adapter between the HDMI3/DVI IN jack on the TV and the DVI jack on the DVD Player or Cable Box/Satellite receiver (Set-Top Box).

2 Connect Audio Cables

between the HDMI3/DVI IN [R-AUDIO-L] jack on the TV and the DVD Player or Cable Box / Satellite receiver (SetTop Box).

DVD Player or Cable Box /

Satellite receiver (Set-Top Box)

Audio Cable (Not supplied)2

HDMI/DVI Cable (Not supplied)1

Each DVD Player or Cable Box / Satellite receiver (Set-Top Box) has a different

➢

back panel configuration.

When connecting a DVD Player or Cable Box / Satellite receiver (Set-Top Box),

➢

match the color of the connection terminal to the cable.

When using an HDMI / DVI cable connection, you must use the HDMI3/DVI IN

➢

jack.

English - 12

TV Rear Panel

English - 13

Connecting a DVD Player or Cable Box / Satellite receiver (Set-Top Box) via Component cables

The side panel jacks on your TV make it easy to connect a DVD Player/Cable Box/Satellite receiver (Set-Top Box) to your TV.

1 Connect Component Cables

between the COMPONENT IN (1 or 2) [Y, PB, PR] jacks on the TV and the COMPONENT [Y, PB, PR] jacks on the DVD Player or Cable Box / Satellite receiver(Set-Top Box).

2 Connect Audio Cables

between the COMPONENT IN (1 or 2) [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the DVD Player or Cable Box / Satellite receiver (Set-Top Box).

TV Rear Panel

DVD Player or Cable Box /

Satellite receiver (Set-Top Box)

Audio Cable (Not supplied)2

Component Cable (Not supplied)

Component video separates the video into Y (Luminance (brightness)), PB (Blue)

➢

and PR (Red) for enhanced video quality. Be sure to match the component video and audio connections. For example, if connecting the Component video cable to COMPONENT IN 1, connect the audio cable to COMPONENT IN 1 also.

Each DVD Player or Cable Box or Satellite receiver (Set-Top Box) has a different

➢

back panel configuration.

When connecting a DVD Player or Cable Box or Satellite receiver (Set-Top Box),

➢

match the color of the connection terminal to the cable.

Connecting a Camcorder

The side panel jacks on your TV make it easy to connect a camcorder to your TV. They allow you to view the camcorder tapes without using a VCR

1 Connect a Video Cable

(or S-Video Cable) between the AV IN 2 [VIDEO] jack on the TV and the VIDEO OUT jack on the Camcorder.

2 Connect Audio Cables

between the AV IN 2 [L-AUDIO-R] jacks on the TV and the AUDIO OUT jacks on the Camcorder.

Camcorder

Each Camcorder has a different back panel configuration.

➢

When connecting a Camcorder, match the color of the connection terminal to the cable

➢

Video Cable (Not supplied)1

Audio Cable (Not supplied)2

TV Side Panel

Connecting a VCR

Video Connection

These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the instructions on pages 10~11). Skip step 1 if you have not yet connected to an antenna or a cable system.

1 Unplug the cable or antenna

from the back of the TV.

2 Connect the cable or antenna

to the ANT IN terminal on the back of the VCR.

3 Connect an Antenna Cable

between the ANT OUT terminal on the VCR and the ANT IN terminal on the TV.

4 Connect a Video Cable

between the VIDEO OUT jack on the VCR and the AV IN (1 or 2) [VIDEO] jack on the TV.

5 Connect Audio Cables

between the AUDIO OUT jacks on the VCR and the AV IN (1 or 2) [VIDEO] jacks on the TV.

VCR Rear Panel

Antenna cable(Not supplied)3

Video Cable(Not supplied)4

Audio Cable(Not supplied)5

TV Rear Panel

If you have a “mono” (non-stereo) VCR, use a Y-connector (not supplied) to hook

➢

up to the right and left audio input jacks of the TV. If your VCR is stereo, you must connect two cables.

Each VCR has a different back panel configuration.

➢

When connecting a VCR, match the color of the connection terminal to the cable.

➢

S-Video Connection

Your Samsung TV can be connected to an S-Video jack on a VCR. (This connection delivers a better picture as compared to a standard VCR.) 1 To begin, follow steps 1–3

in the previous section to connect the antenna or cable to your VCR and your TV.

2 Connect an S-Video Cable

between the S-VIDEO OUT

VCR Rear Panel

jack on the VCR and the AV IN 1 [S-VIDEO] jack on the TV.

3 Connect Audio Cables

between the AUDIO OUT jacks on the VCR and the AV IN 1 or 2 [R-AUDIO-L] jacks on the TV.

Antenna cable(Not supplied)1

S-Video Cable(Not supplied)2

Audio Cable (Not supplied)

TV Rear Panel

An S-Video may be included with your VCR. (If not, check your local electronics store.)

Each VCR has a different back panel configuration.

➢

When connecting a VCR, match the color of the connection terminal to the cable.

➢

English - 14

English - 15

Connecting a Digital Audio System

The side panel jacks on your TV make it easy to connect a Digital Audio System to your TV.

1 Connect an Optical Cable

between the DIGITAL AUDIO OUT (OPTICAL) jack on the TV and the Digital Audio Input (OPTICAL) jacks on the Digital Audio System.

When a Digital Audio System is connected to the “DIGITAL AUDIO OUT (OPTICAL)” jack: Decrease the volume of the TV, and adjust the volume level with the system’s volume control.

TV Rear Panel

Digital Audio System

Optical Cable (Not supplied)

What is OPTICAL?

• An optical cable converts an electric signal into an optical light signal, and transmits it through glass fibers. S/PDIF is a transmission system of digital audio in the form of a light wave that uses a glass conductor.

Each Digital Audio System has a different back panel configuration.

➢

When the receiver (home theater) is set to On, you can hear sound output from

➢

the TV’s Optical jack. When the TV is displaying a DTV(air) signal, the TV will send out 5.1 channel sound to the Home theater receiver. When the source is a digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the Home Theater receiver.

If you want to hear 5.1 channel audio, connect the DIGITAL AUDIO OUT

➢

(OPTICAL) jack on the DVD player or Cable/Satellite Box directly to an Amplifier or Home Theater, not the TV.

Connecting an Amplifier / DVD Home Theater

1 Connect Audio Cables

between the AUDIO OUT [R-AUDIO-L] jacks on the TV and AUDIO IN [L-AUDIO-R] jacks on the Amplifier/DVD Home Theater.

When an audio amplifier is connected to the “AUDIO OUT [R-AUDIO-L]” jacks terminals: Decrease the volume of the TV, and adjust the volume level with the Amplifier’s volume control.

Each Amplifier / DVD Home Theater has a different back panel configuration.

➢

When connecting an Amplifier / DVD Home Theater, match the color of the

➢

connection terminal to the cable.

Amplifier /

DVD Home Theater

Audio Cable (Not supplied)

TV Rear Panel

Connecting a PC

Using the D-Sub Cable 1 Connect a D-Sub Cable

between PC IN [PC] jack on the TV and the PC output jack on your computer.

2 Connect a PC Audio Cable

between the PC IN [AUDIO] jack on the TV and the Audio Out jack of the sound card on your computer.

Using the HDMI/DVI Cable 1 Connect a HDMI/DVI cable

between the HDMI3/DVI IN jack on the TV and the PC output jack on your computer.

Connect a 3.5 mm Stereo mini-plug/2RCA Cable cable between the

DVI IN [R-AUDIO-L] jack on the TV and the Audio Out jack of the sound card on your computer.

Using the D-Sub Cable

PC Audio Cable (Not supplied)2

D-Sub Cable (Not supplied)1

Using the HDMI/DVI Cable

TV Rear Panel

3.5 mm Stereo mini-plug/2RCA Cable (Not supplied)

HDMI/DVI Cable (Not supplied)

Each PC has a different back panel configuration.

➢

When connecting a PC, match the color of the connection terminal to the cable.

➢

When using an HDMI/DVI cable connection, you must use the HDMI3/DVI IN

➢

terminal.

Operation

Turning the TV On and Off

Press the POWER button on the remote control. You can also use the POWER button on the TV.

It may take a while before you see a full picture.

➢

English - 16

English - 17

Plug & Play Feature

The first time you turn on your new TV, choose your basic settings for language, input source and channels, and time of day using the plug and play feature. The TV will store these settings in memory. Storing the channels in memory will allow you to scan the stored channels rather than have to enter their digits each time you want to change channels. When the TV is initially powered on, basic settings proceed automatically:

1 Press the POWER button on the remote control.

The message Menu Language, Store Demo, Channels and Time will be set.

is automatically displayed.

2 Press the ENTER button to enter the language. Press the ▲ or ▼ button to select language, then press the ENTER button. The message Select 'Home Use' when installing this TV in your home. is

automatically displayed.

Menu Langua ge, Store Demo, Channels and Time will be set.

Select Language of the OSD.

Menu Language : English ►

Plug & Play

Enter

Plug & Play

Enter

3 Press the ◄ or ► button to select Store Demo or Home Use, then press the

ENTER button.

The default selection is Home Use.

 ➢

We recommend setting the TV to Home Use for the best picture in your

 ➢

home environment.

Store Demo mode is only intended for use in retail environments.

 ➢

If the unit is accidentally set to Store Demo mode and you want to return

 ➢

to Home Use (Standard): Press the Volume button on the TV. When the volume OSD is displayed, press and hold the MENU button on the TV for 5 seconds.

4 Press the ▲ or ▼ button to memorize the channels of the selected connection,

then press the ENTER button.

Air: Air antenna signal.

 ➢

Cable: Cable antenna signal. Auto: Air and Cable antenna signals.

In Cable mode, you can select the correct analog signal source among

 ➢

STD, HRC, and IRC by pressing the ◄ or ► button, then press the ENTER button. If you have Digital cable, select the signal source for both Analog and Digital. Contact your local cable company to identify the type of cable system that exists in your particular area.

Plug & Play

Select Language of the OSD.

Menu Language : English

Select 'Home Use' when installing this TV in your home.

Store Demo

Select the Antenna source to memorize

Air Cable Auto

Selects the cable system.

Analog Digital

STD

Plug & Play

Move

Plug & Play

Start

Move

English

Español

Français

Enter

Move

Home Use

EnterMove

Start Start

Start

SkipEnter

HRC IRC

HRC IRCSTD

SkipEnter

Continued...

5 The TV will begin memorizing all of the available channels. After all the available channels are stored, the Auto program menu reappears. Press the ENTER button when channel memorization is complete. The Clock Mode menu is displayed.

To stop the search before it has nished, press the ENTER button with

 ➢

stop selected.

6 Press the ENTER button. Press the ▲ or ▼ button to select Manual for setting the current time

manually, then press the ENTER button. The message Set current date and time. is displayed.

If you select Auto, Set to daylight saving time. is displayed, then go to

 ➢

step 9.

7 Press the ◄ or ► button to move to Month, Day, Year, Hour, Minute, or

am/pm.

Set the date and time you want by pressing the ▲ or ▼ button, then press the

ENTER button.

You can set the month, day, year, hour, and minute directly by pressing the

 ➢

number buttons on the remote control.

8 The message Enjoy your watching. is displayed. When you have nished, press the ENTER button.

Even if the ENTER button is not pressed, the message will automatically

 ➢

disappear after several seconds.

Plug & Play

Auto Program in Progress.

DTV Air : -- Air : -DTV Cable : -- Cable: --Cable : --

Stop

Plug & Play

Auto Program is incomplete. 7 channels are memorized. Air : 7 Cable : 0

Plug & Play

Set the Clock Mode.

Clock Mode : Auto

Set current date and time

Month

Hour

Auto

Manual

Plug & Play

Day

Minute

Plug & Play

Enjoy your watching.

Air 3%

Enter Skip

SkipEnterMove

Year 20 0 8

am/pm

SkipEnterAdjustMove

Setting the Clock Automatically 9 Press the ENTER button.

Press the ▲ or ▼ button to select Off or On, then the ENTER button. The message Select the time zone in which you live. is displayed.

10 Press the ▲ or ▼ button to highlight the time zone for your local area (and

to move the highlight to the appropriate time zone on the map of the United States).

Press the ENTER button. If clock is not automatically set, see pages 50~51 to set the clock.

11 The message Enjoy your watching. is displayed. When you have nished, press the ENTER button.

Even if the ENTER button is not pressed, the message will automatically

 ➢

disappear after several seconds.

Continued...

Plug & Play

Set to daylight saving time.

DST : Off

Select the time zone in which you live.

Newfoundland Atlantic

Eastern

Central Mountain Pacific

▼

Off

Move

Plug & Play

Enjoy your watching.

SkipEnter

SkipEnterMove

English - 18

English - 19

If you want to reset this feature...

1 Press the MENU button to display the menu.

Press the ▲ or ▼ button to select Setup, then press the ENTER button.

2 Press the ENTER button to select Plug & Play. For further details on setting

up options, refer to the pages 17~18.

The Plug & Play feature is only available in the TV .

 ➢

Changing Channels

Using the Channel Buttons

1 Press the CH

When you press the CH

➢

in sequence. You will see all the channels that the TV has memorized. (The TV must have memorized at least three channels). You will not see channels that were either erased or not memorized. See page 21 to memorize channels.

or CH

button to change channels.

or CH

button, the TV changes channels

Setup

Plug & Play ►

Language : English Time V-Chip Caption Melody Entertainment : Off

Plug & Play

Menu Language, Store Demo, Channels and Time will be set.

EnterOKReturn

Using the Number Buttons

1 Press the number buttons to go directly to a channel. For example, to select

channel 27, press 2, then 7. The TV will change channels when you press the second number.

For quick channel change, press the number buttons, then press the ENTER

➢

button.

You can press number buttons on Remote control for direct channel access,

➢

press the same Number button again to switch between digital and analog TV channels broadcast by the same station.

Using the “-” Button

The “ ” button is used to select stations that broadcast a digital signal. 1 For example, for Channel 7-1, press 7, then , then 1.

HD indicates the TV is receiving a Digital High Definition signal.

➢

SD indicates the TV is receiving a Standard Definition signal.

For quick channel change, press the number buttons, then press the ENTER

➢

button.

Using the PRE-CH Button to select the Previous Channel

Use the number buttons to quickly tune to any channel. 1 Press the PRE-CH button. The TV will switch to the last channel viewed.

To quickly switch between two channels that are far apart, tune to one

➢

channel, then use the number button to select the second channel. Then use the PRE-CH button to quickly alternate between them.

Adjusting the Volume

Using the Volume Buttons

1 Press the VOL

or VOL

button to increase or decrease the volume.

Using the Mute Button At any time, you can cut off the sound using the MUTE button.

1 Press MUTE and the sound cuts off.

The is displayed on the screen.

2 To turn mute off, press the MUTE button again, or simply press the VOL

VOL

button.

Viewing the Display

The display identifies the current channel and the status of certain audio-video settings.

1 Press the INFO button on the remote control.

The TV will display the channel, the type of sound, and the status of certain picture and sound settings.

TV #1

DTV Air

13-1

Dolby Digital

Wed, Jan 2 12:28am

M. Spillane’s Mike Hammer

Bonocrunch

11:36 pm - 12:42 am

480i 4:3 English

Press the INFO button once more or wait approximately 10 seconds and it disappears automatically.

Viewing the Menus

1 With the power on, press the MENU button.

The main menu appears on the screen. The menu’s left side has icons:

Picture, Sound, Channel, Setup, Input, Application.

2 Press the ▲ or ▼ button to select one of the icons.

Then press the ENTER button to access the icon’s sub-menu.

3 Press the EXIT button to exit.

It takes about one minute until the on-screen menu disappears.

➢

English - 20

Picture

Mode : Standard

Contrast : 80 Brightness : 45 Sharpness : 50 Color : 50 Tint (G/R) : G50/R50 Detailed Settings Picture Options

English - 21

Using the TOOLS Button

You can use the TOOLS button to select your frequently used functions quickly and easily. The TOOLS menu changes depending on which external input mode you are viewing.

1 Press the TOOLS button. The TOOLS menu will appear.

2 Press the ▲/▼ button to select a menu, then press the ENTER button.

3 Press the ▲/▼/◄/►/ENTER buttons to display, change, or use the selected

items.

Picture Mode : Standard Sound Mode : Custom Sleep Timer : Off Add to Favorite Switch to Cable

TOOLS

Device List

For a more detailed description of each function, refer to the corresponding

page.

Move

• 3D Effect, see page 33

• Device List, see page 87

• Picture Mode, see page 24

• Sound Mode, see page 34

• Sleep Timer, see page 53

• Add to Favorite, see page 41

• Delete from Favorite, see page 41

• Switch to Cable, see page 21

Enter

Exit

Memorizing the Channels

Your TV can memorize and store all of the available channels for both air and cable channels. After the available channels are memorized, use the CH to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding and deleting channels (Channel Lists).

Selecting the Video Signal-source

Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e. an Air or a Cable system).

1 Press the MENU button to display the menu.

Press the ▲ or ▼ button to select Channel, then press the ENTER button.

or CH

button to scan through the channels. This eliminates the need

Antenna

Auto Program

Clear Scrambled Channel

Channel List

Fine Tune

Signal Strength

Air ►

2 Press the ENTER button to select Antenna.

Press the ▲ or ▼ button to select Air or Cable, then press the ENTER button. Press the EXIT button to exit.

Easy Setting 1 Press the TOOLS button on the remote control. 2 Press the ▲ or ▼ button to select Switch to Cable or Switch to Air.

3 Press the ENTER button.

Continued...

ChannelChannel

Antenna

Auto Program

Clear Scrambled Channel

Channel List

Fine Tune

Signal Strength

TOOLS

Device List Picture Mode : Standard Sound Mode : Custom Sleep Timer : Off Add to Favorite Switch to Cable

Move

Enter

Air

Cable

Exit

Storing Channels in Memory (Automatic Method)

1 Press the MENU button to display the menu.

Press the ▲ or ▼ button to select Channel, then press the ENTER button.

Channel

2 Press the ▲ or ▼ button to select Auto Program, then press the ENTER

button.

3 Press the ▲ or ▼ button to select an antenna connection, then press the

ENTER button.

Air: Air antenna signal.

➢

Cable: Cable antenna signal. Auto: Air and Cable antenna signals.

Select the antennas to memorize.

Air Cable Auto

4 When selecting the Cable TV system:

Press the ENTER button to start the auto program.

Press the ◄ or ► to select the correct analog signal cable system source

among STD, HRC, and IRC, then press the ENTER button. If you have Digital cable TV, select the cable system signal source for both Analog and Digital.

STD, HRC, and IRC identify various types of cable TV systems. Contact

➢

Select the cable system. Analog

Digital

your local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected.

Auto Program in Progress.

5 The TV begins memorizing all available stations.

After all the available channels are stored, it starts to remove scrambled

➢

DTV Air : -- Air : 3 DTV Cable : -- Cable : --

channels (see page 45). The Auto program menu then reappears.

If you want to stop Auto Programming, press the ENTER button.

 ➢

The Stop Auto Program? message will be displayed. Select Yes by press-

ing the ◄ or ► button, then press the ENTER button.

Press the EXIT button to exit.

Auto Program is incomplete. 3 channels are memorized. Air : 3 Cable : 0

Antenna : Air

Auto Program ►

Clear Scrambled Channel

Channel List

Fine Tune

Signal Strength

Auto Program

Start

Start Start

Move

Auto Program

STD

Move

Auto Program

HRC IRC

HRC IRCSTD

Start

Stop

ReturnEnter

Air 3 3%

Enter Return

ReturnEnter

English - 22

English - 23

To Select the Source

Use to select TV or other external input sources such as DVD players or Cable Box/Satellite receivers (Set-Top Box) connected to the TV. Use to select the input source of your choice.

1 Press the MENU button to display the menu.

Press the ▲ or ▼ button to select Input, then press the ENTER button.

2 Press the ENTER button to select Source List.

Press the ▲ or ▼ button to select the signal source, then press the ENTER button.

Available signal sources: TV, AV1, AV2, S-Video, Component1,

➢

Component2, PC, HDMI1, HDMI2, HDMI3/DVI, USB.

You can choose only those external devices that are connected to the TV. In

➢

the Source List, connected inputs will be highlighted and sorted to the top. Inputs that are not connected will be sorted to the bottom.

Using the Color buttons on the remote with the Source list.

➢

• Red (Refresh): Refreshes the connecting external devices.

• TOOLS (Option): Displays the Edit Name and Information menus.

Input

Source List

Edit Name

AV1 AV2 S-Video Component1 Component2 PC

Refresh Option

----

TOOLS

You can also press the SOURCE button on the remote control to view an external signal source.

To Edit the Input Source Name

You can name the device connected to the input jacks to make your input source selection easier.

1 Press the MENU button to display the menu.

Press the ▲ or ▼ button to select Input, then press the ENTER button. Press the ▲ or ▼ button to select Edit Name, then press the ENTER button.

2 Press the ▲ or ▼ button to select AV1, AV2, S-Video, Component1,

Component2, PC, HDMI1, HDMI2, or HDMI3/DVI input jack, then press thethen press the ENTER button.

3 Press the ▲ or ▼ button to select VCR, DVD, Cable STB, Satellite STB, PVR

STB, AV Receiver, Game, Camcorder, PC, TV, IPTV, Blu-Ray, HD DVD or Digital Media Adapter input source, then press the ENTER button.

Press the EXIT button to exit.

When a PC with a resolution of 1920 x 1080@60Hz is connected to the

➢

HDMI3/DVI port, you should set the HDMI3/DVI mode to PC in the Edit Name of the Input mode.

Source List

Input

EditName  ►

Edit Name

AV1 : AV2 : S-Video : Component1 : Component2 : PC : HDMI1 :

Edit Name

AV1 :

AV2 : S-Video : Component1 : Component2 : PC : HDMI1 :

----

►

----

Enter ReturnMove

----

VCR

----

DVD

----

Cable STB

----

Satellite STB PVR STB

Enter ReturnMove

Picture Control

Changing the Picture Standard

You can select the type of picture which best corresponds to your viewing requirements.

1 Press the MENU button to display the menu.

Press the ENTER button to select Picture.

Picture

Mode : Standard ►

Contrast : 80 Brightness : 45 Sharpness : 50 Color : 50 Tint (G/R) : G50/R50 Detailed Settings Picture Options

2 Press the ENTER button to select Mode.

Picture

Press the ▲ or ▼ button to select Dynamic, Standard, or Movie. Press the ENTER button.

• Dynamic: Select the picture for high-definition in a bright room.

• Standard: Select the picture for the optimum display in the normal environment.

• Movie: Select the picture for viewing movies in a dark room.

3 Press the EXIT button to exit.

Easy Setting 1 Press the TOOLS button on the remote control. 2 Press the ▲ or ▼ button to select Picture Mode. 3 Press the ◄ or ► button to select the required option.

Picture Mode : Standard Sound Mode : Custom Sleep Timer : Off Add to Favorite Switch to Cable

Customizing the Picture Settings

Your television has several setting options that allow you to control the picture quality.

1 To select the desired picture mode, follow the “Changing the Picture Standard”

instructions number 1 to 2.

2 Press the ▲ or ▼ button to select Contrast, Brightness, Sharpness, Color, or

Tint (G/R), then press the ENTER button.

3 Press the ◄ or ► button to decrease or increase the value of a particular item.

Press the ENTER button.

Press the EXIT button to exit.

• When you make changes to Contrast, Brightness, Sharpness, Color, or

➢

Tint (G/R) the OSD will be adjusted accordingly.

• When in PC mode, Tint(G/R), Sharpness and Color are not available.

• Each adjusted setting will be stored separately according to its input mode.

Picture

Mode :

Contrast : 100 Brightness : 45 Sharpness : 50 Color : 50 Tint (G/R) : G50/R50 Detailed Settings Picture Options

TOOLS

Device List

Move Enter

Mode

Contrast : 80 ►

Brightness : 45 Sharpness : 50 Color : 50 Tint (G/R) : G50/R50 Detailed Settings Picture Options

Dynamic

Standard

Movie

Standard

Exit

80Contrast

ReturnEnterAdjustMove

• Contrast: Adjusts the contrast level of the picture.

• Brightness: Adjusts the brightness level of the picture.

• Sharpness: Adjusts the edge definition of the picture.

• Color: Adjusts color saturation of the picture.

• Tint(G/R): Adjusts the color tint of the picture by compensating the red and

green color.

English - 24

English - 25

Adjusting the Detailed Settings

Samsung’s new TVs allow you to make even more precise picture settings than previous models. See below to adjust detailed picture settings.

Activating Detailed Settings

1 Press the MENU button to display the menu. Press the ENTER button to select Picture.

2 Press the ENTER button to select Mode.

Press the ▲ or ▼ button to select Standard or Movie, then press the ENTER

button.

Detailed Settings is available in Standard or Movie mode.

➢

3 Press the ▲ or ▼ button to select Detailed Settings, then press the ENTER

button.

In PC mode, you can only make changes to Dynamic Contrast, Gamma

➢

and White Balance from among the Detailed Settings items.

Activating Black adjust

You can select the black level on the screen to adjust the screen depth.

4 Press the ▲ or ▼ button to select Black adjust, then press the ENTER button.

5 Press the ▲ or ▼ button to select Off, Low, Medium or High. Press the ENTER button.

• Off: Turns off the black adjustment function.

• Low: Sets the black color depth to low.

• Medium: Sets the black color depth to medium.

• High: Sets the black color depth to high.

Color : 50 Tint (G/R) : G50/R50

Picture

Detailed Settings ►

Picture Options Picture Reset

Detailed Settings

Black Adjust : Off ► Dynamic Contrast : Low Gamma : +1 White Balance : 0 Flesh Tone : 0 Edge Enhancement : On xvYCC : Off

Move

Black Adjust : Low

Move

ReturnEnter

Off

Low Medium High

ReturnEnter

Activating Dynamic Contrast

You can adjust the screen contrast so that the optimal contrast is provided.

6 Press the ▲ or ▼ button to select Dynamic Contrast, then press the

ENTER button.

7 Press the ▲ or ▼ button to select Off, Low, Medium or High.

Press the ENTER button.

• Off: Turns off the dynamic contrast adjustment function.

• Low: Sets the dynamic contrast to low.

• Medium: Sets the dynamic contrast to medium.

• High: Sets the dynamic contrast to high.

Continued...

Off

Low

Dynamic Contrast : Low

Move

Medium High

ReturnEnter

Activating Gamma

You can adjust the Primary Color (Red, Green, Blue) Intensity. (-3 ~ +3)

8 Press the ▲ or ▼ button to select Gamma, then press the ENTER button. 9 Press the ◄ or ► button to decrease or increase the value.

Press the ENTER button.

Gamma

Adjust

Enter Return

Activating White Balance

You can adjust the color temperature for more natural picture colors.

10 Press the ▲ or ▼ button to select White Balance, then press the ENTER button.

11 Select the required option by pressing the ▲ or ▼ button, then press the

ENTER button.

12 Press the ◄ or ► button to decrease or increase the value of a particular item.

(-10~+10)

Press the ENTER button.

Changing the adjustment value will refresh the adjusted screen.

➢

Flesh Tone

You can emphasize the pink flesh tone in the picture.

13 Press the ▲ or ▼ button to select Flesh Tone, then press the ENTER button.

14 Press the ◄ or ► button to decrease or increase the value.

Press the ENTER button.

Changing the adjustment value will refresh the adjusted screen.

➢

Detailed Settings

Black Adjust : Off Dynamic Contrast : Low Gamma : +1 White Balance : 0 ► Flesh Tone : 0 Edge Enhancement : On xvYCC : Off

Move

White Balance

Adjust

Detailed Settings

Black Adjust : Off Dynamic Contrast : Low Gamma : +1 White Balance : 0 Flesh Tone : 0 ► Edge Enhancement : On xvYCC : Off

Move

Flesh Tone

ReturnEnter

Enter Return

ReturnEnter

Activating Edge Enhancement

You can emphasize object boundaries in the picture.

15 Press the ▲ or ▼ button to select Edge Enhancement, then press the ENTER button.

16 Press the ▲ or ▼ button to select Off or On. Press the ENTER button.

Continued...

English - 26

Adjust

Enter Return

Detailed Settings

Black Adjust : Off Dynamic Contrast : Low Gamma : +1 White Balance : 0 Flesh Tone : 0 Edge Enhancement : On ► xvYCC : Off

Move

Edge Enhancement : On

Move

ReturnEnter

Off

ReturnEnter

English - 27

Activating xvYCC

Setting the xvYCC mode to On increases detail and color space when watching movies from an external device (ie. DVD player) connected to the HDMI or Component IN jacks.

17 Press the ▲ or ▼ button to select xvYCC, then press the ENTER button.

18 Press the ▲ or ▼ button to select Off or On.

Press the ENTER button.

xvYCC is available when the picture mode is set to Movie, and the

 ➢

external input is set to HDMI or Component mode.

Configuring Picture Options

Detailed Settings

Black Adjust : Off Dynamic Contrast : Low Gamma : +1 White Balance : 0 Flesh Tone : 0 Edge Enhancement : On xvYCC : Off ►

Move

xvYCC : On

Move

ReturnEnter

Off

ReturnEnter

Activating Picture Options 1 Press the MENU button to display the menu.

Press the ENTER button to select Picture.

2 Press the ▲ or ▼ button to select Picture Options, then press the ENTER

button.

3 Press the ▲ or ▼ button to select a particular item. Press the ENTER button. ➢ When you are satised with your setting, press the ENTER button.

In PC mode, you can only make changes to the Color Tone, Position,

➢

Size and Color Gamut from among the items in Picture Options.

Adjusting the Color Tone

1 Follow the Activating Picture Options instructions numbers 1 and 2.

2 Press the ▲ or ▼ button to select Color Tone, then press the ENTER button.

3 Press the ▲ or ▼ button to select Cool2, Cool1, Normal, Warm1 or Warm2.

Press the ENTER button.

➢ Warm1 or Warm2 is only activated when the picture mode is Movie. ➢ Settings can be adjusted and stored for each external device

you have connected to an input of the TV.

Tint (G/R) : G50/R50 Detailed Settings

Picture

PictureOptions  ►

Picture Reset

Picture Options

Color Tone :

Size : Position : Digital NR : DNle : 2min HDMI Black Level : 2min Film Mode : Off

Move

Cool2

Cool1

Normal

Warm1

Warm2

ReturnEnter

Continued...

Changing the Screen Size

Occasionally, you may want to change the size of the image on your screen. Your

TV comes with six screen size options, each designed to work best with specic

types of video input. Your cable box or satellite receiver may have its own set of screen sizes as well. In general, though, you should view the TV in 16:9 mode as much as possible.

1 Follow the Activating Picture Options instructions numbers 1 and 2. (Refer to page 27)

2 Press the ▲ or ▼ button to select Size, then press the ENTER button.

3 Press the ▲ or ▼ button to select the screen format you want.

Press the ENTER button. Press the EXIT button to exit.

• 16:9 : Sets the picture to 16:9 wide mode.

• Zoom1 : Magnifies the size of the picture on the screen.

• Zoom2 : Expands the Zoom1 format picture.

• Wide Fit : Enlarges the aspect ratio of the picture to fit the entire screen.

• 4:3 : Sets the picture to 4:3 normal mode.

• Just Scan : Use this function to see the full image without any cutoff when

DTV(1080i), Component(1080i/1080p) or HDMI(720P/1080i/1080P) signals are input.

After selecting Zoom1, Zoom2 or Wide Fit:

 ➢

Color Tone : Cool1 Size : 16:9 ►

Position Digital NR : Auto

DNle : Off HDMI Black Level : Normal

Film Mode : Off

16:9

Zoom1

Zoom2

Wide Fit

4:3

Just Scan

Picture Options

Move

Size

Move

ReturnEnter

Press the ◄ or ► button to select Position, then press the ENTER button. Press the ▲ or ▼ button to move the picture up and down.

Reset: Press the ◄ or ► button to select Reset, then press the ENTER button. You can initialize the setting.

HD (High Definition)

 ➢

16:9 - 1080i/1080p (1920x1080), 720p (1280x720)

Settings can be adjusted and stored for each external device you have connected to an input of the TV.

 ➢

Input Source Picture Size

ATV, Video, S-Video, DTV(480i, 480p), Component(480i, 480p),

16:9, Zoom1, Zoom2, 4:3

HDMI(480p) DTV(1080i), Component(1080i,1080p), HDMI(720p, 1080i, 1080p)

16:9, 4:3, Wide Fit, Just Scan DTV(720p) ,Component(720p) 16:9, 4:3, Wide Fit PC, HDMI3/DVI(PC timing) Wide TV, Wide PC, 4:3

Alternately, you can press the P.SIZE button on the remote control repeatedly to change the picture size.

Continued...

English - 28

English - 29

16:9

Sets the picture to 16:9 wide mode.

Zoom1

The screen size when Wide screen is vertically enlarged.

Zoom2

The screen size when the Zoom1 screen is vertically enlarged.

Wide Fit

Enlarges the aspect ratio of the picture to fit the entire screen.

4:3

Sets the picture to 4:3 normal mode.

Just Scan

Use this function to see the full image without any cutoff when HDMI (720p/1080i/1080p) or DTV(1080i),Component(1080i/ 1080p) signals are input.

Adjusting the Screen Position

You can adjust the horizontal and vertical position of the screen. 1 Follow the Activating Picture Options instructions numbers 1 and 2.

(Refer to page 27)

2 Press the ▲ or ▼ button to select Posion, then press the ENTER button.

Digital Noise Reduction

If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature to help reduce any static and ghosting that may appear on the screen.

1 Follow the Activating Picture Options instructions numbers 1 and 2. (Refer to page 27)

2 Press the ▲ or ▼ button to select Digital NR, then press the ENTER button.

3 Press the ▲ or ▼ button to select Off, Low, Medium, High or Auto.

Press the ENTER button.

• Off: Turns the screen noise reduction function off.

• Low: Reduces screen noise at a low level.

• Medium: Reduces screen noise at a medium level.

• High: Reduces screen noise at a high level.

• Auto: Automatically recognizes and reduces screen noise.

Press the EXIT button to exit.

Continued...

Picture Options

Color Tone : Cool1 Size : 16:9 Position ► Digital NR : Auto

DNle : Off HDMI Black Level : Normal

Film Mode : Off

Move

Position

Adjust

Picture Options

Color Tone : Cool1 Size : 16:9

Position Digital NR : Auto ►

DNle : Off HDMI Black Level : Normal

Film Mode : Off

Move

Picture Options

Color Tone : Cool1 Size : 16:9

Position Digital NR : High DNle : Off HDMI Black Level : Normal Film Mode : Off

Off Low Medium Hight

Auto

Move

ReturnEnter

DNIe (Digital Natural Image engine)

This TV includes the DNIe function to provide high visual quality. If you set DNIe to on, you can view the screen with the DNIe feature activated.

1 Follow the Activating Picture Options instructions numbers 1 and 2. (Refer to page 27)

2 Press the ▲ or ▼ button to select DNIe, then press the ENTER button.

Picture Options

Color Tone : Cool1 Size : 16:9

Position Digital NR : Auto DNle : Off ►

HDMI Black Level : Normal

Film Mode : Off

3 Press the ▲ or ▼ button to select On or Off or then press the ENTER button.

• Off: Switches off the DNIe mode.

• On: Switches on the DNIe mode.

Press the EXIT button to exit. ➢ DNIe™ (Digital Natural Image engine)

This feature brings you a more detailed image with 3D noise reduction

and detailed, contrast and white enhancement. ➢ DNIe is only available in Dynamic mode. ➢ This function doesn't work when the Input Source is PC.

Setting the HDMI Black Level

Use this function to adjust the Black Level of the picture while in HDMI mode. 1 Follow the Activating Picture Options instructions numbers 1 and 2.

(Refer to page 27)

2 Press the ▲ or ▼ button to select HDMI Black Level, then press the ENTER

button.

Move

Picture Options

Color Tone : Cool1 Size : 16:9

Position

Digital NR : Autoh

DNle : Off HDMI Black Level : Normal Film Mode : Off

Color Tone : Cool1 Size : 16:9

Position Digital NR : Auto DNle : Off ► HDMI Black Level : Normal Film Mode : Off

Off

Move

Picture Options

Move

ReturnEnter

3 Press the ▲ or ▼ button to select Normal or Low, then press the ENTER

button.

• Normal: The screen gets brighter.

• Low: The screen gets darker.

This function is active only when an external device is connected to via

 ➢

HDMI. HDMI Black Level function may not be compatible with all external devices.

Press the EXIT button to exit.

Continued...

English - 30

Picture Options

Color Tone : Cool1 Size : 16:9

Position Digital NR : Auto DNle : Off

HDMI Black Level : Normal

Film Mode : Off

Normal

Low

Move

ReturnEnter

+ 165 hidden pages