Samsung e210 Service Manual

GSM TELEPHONE

SGH-E210

GSM TELEPHONE

CONTENTS

Safety Precautions

1.

Specification

2.

Product Function

3.

Array course control

4.

Exploded View and Parts List

5.

MAIN Electrical Parts List

6.

Block Diagrams

7.

PCB Diagrams

8.

Flow Chart of Troubleshooting

9.

Reference data

10.

Safety Precautions

1.

Repair Precaution

1-1.

Repair in Shield Box, during detailed tuning.

●

Take specially care of tuning or test,

because specipicty of cellular phone is sensitive for surrounding interference(RF noise).

Be careful to useakind of magnetic object or tool,

●

because performance of parts is damaged by the influence of manetic force.

Surely useastandard screwdriver when you disassemble this product,

●

otherwise screw will be worn away.

Useathicken twisted wire when you measure level.

●

thicken twisted wire has low resistance, therefore error of measurement is few.

A

Repair after separate Test Pack and Set because for short danger(for example an

●

overcurrent and furious flames of parts etc) when you repair board in condition of

connecting Test Pack and tuning on.

Take specially care of soldering, because Land of PCB is small and weak in heat.

●

Surely tune on/off while using AC power plug, becausearepair of battery charger is

●

dangerous when tuning ON/OFF PBA and Connector after disassembing charger.

Don't use as you pleases after change other material than replacement registered on SEC

●

System. Otherwise engineer in charge isn't charged with problem that you don't keep this

rules.

1-1

SAMSUNG Proprietary-Contents may change without notice

This Document can not be used without Samsung's authorization

Safety Precautions

ESD(Electrostatically Sensitive D evices) Precaution

1-2.

Several semiconductor may be damaged easilly by static electricity. Such parts are called by

ESD(Electrostatically Sensitive Devices), for example IC,BGA chip etc. Read Precaution below.

You can prevent from ESD damage by static electricity.

Remove static electricity remained your body before you touch semiconductor or parts with

●

semiconductor. There are ways that you touch an earthed place or wear static electricity

prevention string on wrist.

Use earthed soldering steel when you connect or disconnect ESD.

●

Use soldering removing tool to break static electricity.,otherwise ESD will be damaged by

●

static electricity.

Don't unpack until you set up ESD on product. Because most of ESD are packed by box

●

and aluminum plate to have conductive power,they are prevented from static electricity.

You must maintain electric contact between ESD and place due to be set up until ESD is

●

connected completely to the proper place oracircuit board.

1-2

SAMSUNG Proprietary-Contents may change without notice

This Document can not be used without Samsung's authorization

Specification

2.

GSM General Specification

2-1.

GSM 900 DCS1800 PCS1900

Freq. Band[MHz]

Uplink/Downlink

ARFCN range

Tx/Rx spacing 45MHz 95MHz 80MHz

Mod. Bit rate/

Bit Period

Time Slot Period

/Frame Period

Modulation 0.3GMSK 0.3GMSK 0.3GMSK

MS Power 33dBm~5dBm 30dBm~0dBm 30dBm~0dBm

Power Level 5

880~915 925~960

0~124

& 975~1023

270.833Kbps

3.692us

576.9us

4.615ms

pcl~19pcl

1710~1785 1805~1880

512~885 512~810

270.833Kbps

3.692us

576.9us

4.615ms

pcl~15pcl

0

1850~1910 1930~1990

270.833Kbps

3.692us

576.9us

4.615ms

pcl~15pcl

0

Sensitivity -102dBm -100dBm -102dBm

TDMA Mux 8 8 8

Cell Radius 35Km 2Km 2Km

2-1

Speclflcation

GSM Tx Power Class

2-2.

TX Power

control level

533±2

631±3

729±3

827±3

925±3

10 23±3

11 21±3

12 19±3

13 17±3

14 15±3

15 13±3

GSM900

dBm

TX Power

control

level

030±2

128±3

226±3

324±3

422±3

520±3

618±3

716±3

814±3

912±4

10 10±4

DCS1800

dBm

TX Power

control

level

030±2

128±3

226±3

324±3

422±3

520±3

618±3

716±3

814±3

912±4

10 10±4

PCS1900

dBm

16 11±5

17 9±5

18 7±5

19 5±5

dBm

11 8±4

12 6±4

13 4±4

14 2±5

15 0±5

2-2

dBm

11 8±4

12 6±4

13 4±4

14 2±5

15 0±5

dBm

Product Function

3.

Main Function

Camera and camcorder

-

Music player

-

FM radio

-

Offlime mode

-

Bluetooth

-

Web browser

-

Multimedia Message Service(MMS)

-

SOS message

-

Organiser

-

3-1

SAMSUNG Proprietary-Contents may change without notice

This Document can not be used without Samsung's authorization

Array course control

4.

Test Jig(GH80-03312A)

Test Cable(GH39-00830A)

RF Test Cable(GH39-00

4-1

SAMSUNG Proprietary-Contents may change without notice

This Document can not be used without Samsung's authorization

397

A)

Array course control

Software Downloading

4-1.

•

4-2.

•

Downloading Binary Files

Three binary files for downloading SGH-E210

E210XXYY.s3:Main source code binary.

–

Pre-requsite for Downloading

Downloader Program(OptiFlash.exe

)

E210 Mobile Phone

Data Cable

Binary files

.

4-2

SAMSUNG Proprietary-Contents may change without notice

This Document can not be used without Samsung's authorization

Array course control

4-3.

1.

2.

platform

Choose hardware platform for the downloader file setting.

S/W Downloader Program

Load the binary download program by executing the“OptiFlash.exe

Select the“Options

”.

”->“

Settings

”->“

Generic

”->“

Specify hardware

”

Set the everything else as the default values which are shown b elow

4-3

SAMSUNG Proprietary-Contents may change without notice

This Document can not be used without Samsung's authorization

Array course control

Select the COM port when the download cable is connected

3.

Up to

ports are supported. Additionally you can select the maximum

64 transfer speed OptiFlash will use to communicate with the phone. However, OptiFlash will useaslower speed if either the PC’sor the phone’sserial hardware is incapable of handling the selected speed

4-4

SAMSUNG Proprietary-Contents may change without notice

This Document can not be used without Samsung's authorization

Array course control

Select the“Flash&Verify

4.

”->“

Browse

”

Set the directory path and choose the latest s/w binary, for example

E210XXYY.s3

“

for the downloader binary setting.

”,

Make sure that not to change the reserved memory regions.

In case of E210 the reserved memory regions are

x23c00000

-0

SAMSUNG Proprietary-Contents may change without notice

This Document can not be used without Samsung's authorization

~0

x23ffffff

4-5

:

Array course control

Click“OK”button then press“Flash

5. Before pressing‘Flash’button, push the button

(

time.Then press‘Flash

Downloader will upload the binary file as below for the downloading.

’.)

”.

and‘END’at the same

‘*’

When downloading is finished successfully, there is

6.

message.

After finishing downloading, Certain memory resets should be done to

7.

guarantee the normal performance.

Confirm the downloaded version name and etc.

8.

Full Reset

*#1234#

*2767*3855#

:

All is well

a“

”

4-6

SAMSUNG Proprietary-Contents may change without notice

This Document can not be used without Samsung's authorization

Exploded View and Parts List

5.

5-1.

QFU01

QME16

QLC01

QMW01

QCA01

Cellular phone Exploded View

QMO01

QSP01

QSP05

QCR71

QMP01

QAN11

QVO01

QKP01

QIF01

QCK01

QFR01

QSD01

QMI03

QME01

QMI01

QSH01

QFL01

QCR05

QSC04

QHI01

QAN02

QRE01

QRF01

QCR54

QBA01

QBA00

5-1

SAMSUNG Proprietary-Contents may change without notice

This Document can not be used without Samsung's authorization

Main Electrical Parts List

Cellular phone Parts list

5-2.

Design LOC Discription SEC CODE

QAN11

QBA00

QBA01

QCA01

QCR05

QCR54

QCR71

QFU01

QKP01

QME01

QME16

QMI01

QMI03

QMO01

QMP01

QMW01

QSC04

QSH01

QSP01

QRF01

QLC01

QFL01

QRE01

QFR01

ASSY-CUSHION-CUSHION RUBBER IN GH98-01077A

ASSY COVER-BATT GH98-05107A

INNER BATTERY PACK-800MAH,MAIN GH43-02589A

CAMERA MODULE-SGHE210 GH59-04657A

SCREW-MACHINE

6001-001478

6001-001645

6001-002095

ASSY CASE-FOLDER UPPER GH98-03571A

ASSY KEYPAD-MAIN(XEN/ZK) GH98-05104A

DOME SHEET-SGHE210 TF DOME SHE GH59-04560A

ASSY ETC-SGHE210 CON TO CON GH59-04024A

MICROPHONE-ASSY-SGHE210 GH30-00408A

RMO-MIC HOLDER GH73-05342A

MOTOR BLOWER-SCHA530 MOTOR GH31-00047A

PBA MAIN-SGHE210 GH92-03388A

ASSY COVER-MAIN WINDOW GH98-05105A

TAPE-SCREW SHEET GH74-32473A

IPR COVER-SHIELD GH70-02471A

SPEAKER

3001-002188

TAPE-RF SHEET GH74-32474A

ELA UNIT-SGHE210 LCD MODULE SV GH96-02766A

ASSY CASE-FOLDER LOWER GH98-03572A

QHI01 ASSY MEC-HINGE GH75-09605A

QSP05 ASSY DECO-SPK IN GH98-05106A

ASSY CASE-REAR GH98-03574A

QAN02 INTENNA-SGHE210 GH42-01145A

ASSY CASE-FRONT GH98-03573A

QCK01 PMO KEY-CAMERA GH72-42023A

QIF01 PMO COVER-IF GH72-42196A

QSD01 PMO COVER-MICRO SD GH72-42157A

QVO01 PMO KEY-VOLUME GH72-42160A

5-2

SAMSUNG Proprietary-Contents may change without notice

This Document can not be used without Samsung's authorization

Main Electrical Parts List

Discription SEC CODE

BAG PE

6902-000297

ADAPTOR-ATADS10EBE,BLK,EU GH44-01702A

EARPHONE-SGHE210,HEADSET,BLK,A GH59-04535A

LABEL(P)-UNIT SEAL GH68-00518B

LABEL(R)-WATER SOAK GH68-09361A

MANUAL USERS-EU ENGLISH GH68-13874A

MANUAL USERS-EU PORTUGUESE GH68-13884A

LABEL(R)-MAIN(EU) GH68-13957A

BOX(P)-UNIT MAIN(EU) GH69-05052A

CUSHION-CASE TA2 MA2 GH69-05053A

MPR-REMOVE TAPE LCD GH74-13804A

TAPE GASK GH74-31842A

TAPE INSU GH74-32033A

TAPE GH74-33512A

TAPE-LOWER GH74-33601A

TAPE GH74-33602A

TAPE GH74-33809A

TAPE GASK GH74-33810A

SPONGE-SOUND LCD GH74-33913A

VINYL-BOHO UPPER

2

GH74-34251A

5-3

SAMSUNG Proprietary-Contents may change without notice

This Document can not be used without Samsung's authorization

MAIN Electrical Parts List

6.

SEC CODE Design LOC Discription STATUS

GH71-06262A ANT100 NPR-ANTENNA CONTACT V2 SA

GH71-06262A ANT101 NPR-ANTENNA CONTACT V2 SA

GH13-00044A UCD301 IC ASIC-SGHE490 SA

4709-001422

4302-001130

4202-001325

3711-006228

3711-006015

3710-002499

3709-001392

3709-001384

3705-001358

3404-001152

3301-001912

3301-001120

2904-001600

2904-001599

2904-001592

2801-004466

2801-004455

2801-004340

2703-003196

2703-002910

2703-002906

2703-002900

2703-002782

2703-002603

2703-002485

2703-002208

2703-002207

2404-001484

MOD101 BLUETOOTH MODULE SA

BAT300 BATTERY-LI(2ND) SA

ANT102 ANTENNA-CHIP SA

BTC400 HEADER-BATTERY SA

HEA400 HEADER-BOARD TO BOARD SA

IFC400 SOCKET-INTERFACE SA

CN201 CONNECTOR-CARD EDGE SA

SIM200 CONNECTOR-CARD EDGE SA

RFS100 CONNECTOR-COAXIAL SA

TAC400 SWITCH-TACT SA

TAC401 SWITCH-TACT SA

TAC402 SWITCH-TACT SA

L109 BEAD-SMD SA

L400 BEAD-SMD SA

L401 BEAD-SMD SA

F103 FILTER-SAW SA

F102 FILTER-SAW SA

F101 FILTER-SAW SA

OSC301 CRYSTAL-SMD SA

OSC100 CRYSTAL-SMD SA

OSC300 CRYSTAL-SMD SA

L500 INDUCTOR-SMD SA

L101 INDUCTOR-SMD SA

L102 INDUCTOR-SMD SA

L104 INDUCTOR-SMD SA

L106 INDUCTOR-SMD SA

L300 INDUCTOR-SMD SA

L103 INDUCTOR-SMD SA

L105 INDUCTOR-SMD SA

L100 INDUCTOR-SMD SA

L108 INDUCTOR-SMD SA

L107 INDUCTOR-SMD SA

TA401 C-TA,CHIP SA

TA402 C-TA,CHIP SA

6-1

SAMSUNG Proprietary-Contents may change without notice

This Document can not be used without Samsung's authorization

Exploded View and Parts List

SEC CODE Design LOC Discription STATUS

2404-001414

2404-001406

2404-001381

2203-006979

2203-006838

2203-006648

2203-006585

2203-006562

TA403 C-TA,CHIP SA

TA404 C-TA,CHIP SA

TA400 C-TA,CHIP SA

TA405 C-TA,CHIP SA

TA406 C-TA,CHIP SA

C235 C-CER,CHIP SA

C126 C-CER,CHIP SA

C127 C-CER,CHIP SA

C215 C-CER,CHIP SA

C314 C-CER,CHIP SA

C349 C-CER,CHIP SA

C350 C-CER,CHIP SA

C351 C-CER,CHIP SA

C116 C-CER,CHIP SA

C466 C-CER,CHIP SA

C467 C-CER,CHIP SA

C400 C-CER,CHIP SA

C401 C-CER,CHIP SA

C128 C-CER,CHIP SA

C132 C-CER,CHIP SA

C134 C-CER,CHIP SA

C135 C-CER,CHIP SA

C223 C-CER,CHIP SA

C313 C-CER,CHIP SA

C317 C-CER,CHIP SA

C328 C-CER,CHIP SA

C331 C-CER,CHIP SA

C340 C-CER,CHIP SA

C341 C-CER,CHIP SA

C342 C-CER,CHIP SA

C343 C-CER,CHIP SA

C344 C-CER,CHIP SA

C345 C-CER,CHIP SA

C346 C-CER,CHIP SA

C347 C-CER,CHIP SA

C348 C-CER,CHIP SA

C368 C-CER,CHIP SA

6-2

SAMSUNG Proprietary-Contents may change without notice

This Document can not be used without Samsung's authorization