Samsung E1360B Service Manual
GSM TELEPHONE
GT-E1360B
GSM TELEPHONE
CONTENTS
Safety Precautions
1.
Specification
2.
Product Function
3.
Array course control
4.
Exploded View and Parts list
5.
MAIN Electrical Parts List
6.
Block Diagrams
7.
PCB Diagrams
8.
Chart of Troubleshooting
9.
Reference data
10.
Disassembly and Assembly
11.
Instructions
Safety Precautions
1.
Repair Precaution
1-1.
Repair in Shield Box, during detailed tuning.
●
Take specially care of tuning or test, because cellular phone is sensitive for surrounding
interference(RF noise).
Be careful to useakind of magnetic object or tool, because performance of parts is damaged by
●
the influence of magnetic force.
Surely useastandard screwdriver when you disassemble this product, otherwise screw will be
●
worn away.
Useathicken twisted wire when you measure level.
●
thicken twisted wire has low resistance, therefore errors of measurement are few.
A
Repair after separate Test Pack and Set because for short danger(for example an
●
overcurrent and furious flames of parts etc) when you repair board in condition of connecting Test
Pack and tuning on.
Take specially care of soldering, because Land of PCB is small and weak in heat.
●
Surely tune on/off while using AC power plug, becausearepair of battery charger is dangerous
●
when tuning ON/OFF PBA and Connector after disassembling charger.
Don't use as you pleases after change other material than replacement registered on SEC System.
●
Otherwise engineer in charge isn't charged with problem that you don't keep this rules.
1-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
afety Precautions
S
ESD(Electrostatically Sensitive Devices) Precaution
1-2.
Several semiconductor may be damaged easily by static electricity. Such parts are called by ESD
Electrostatically Sensitive Devices), for example IC,BGA chip etc. Read Precaution below.
(
You can prevent from ESD damage by static electricity.
Remove static electricity remained your body before you touch semiconductor or parts with
●
semiconductor. There are ways that you touch an earthed place or wear static electricity prevention
string on wrist.
Use earthed soldering steel when you connect or disconnect ESD.
●
Use soldering removing tool to break static electricity.,otherwise ESD will be damaged by
●
static electricity.
Don't unpack until you set up ESD on product. Because most of ESD are packed by box and
●
aluminum plate to have conductive power,they are prevented from static electricity.
You must maintain electric contact between ESD and place due to be set up until ESD is
●
connected completely to the proper place oracircuit board.
1-2
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Specification
2.
2-1.
GSM General Specification
Freq. Band[MHz]
Uplink/Downlink
ARFCN range 0~124 & 975~1023 512~885
Tx/Rx spacing 45MHz 95MHz
Mod. Bit rate/
Bit Period
Time Slot Period/Frame
Period
EGSM 900 DCS1800
880~915
925~960
270.833kbps
3.692us
576.9us
4.615ms
1710~1785
1805~1880
270.833kbps
3.692us
576.9us
4.615ms
Modulation 0.3GMSK 0.3GMSK
MS Power 33dBm~5dBm 30dBm~0dBm
Power Class
Sensitivity -102dBm -100dBm
TDMA Mux 8 8
Cell Radius 35Km 2Km
(
max
4
+33
dBm)
(
max
1
+30
dBm)
2-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Specification
2-2.
GSM TX power class
TX Power
control level
533±2
631±2
729±2
827±2
925±2
10 23±2
11 21±2
GSM900
dBm
dBm
dBm
dBm
dBm
dBm
dBm
TX Power
control level
030±3
128±3
226±3
324±3
422±3
520±3
618±3
DCS1800
dBm
dBm
dBm
dBm
dBm
dBm
dBm
12 19±2
13 17±2
14 15±2
15 13±2
16 11±3
17 9±3
18 7±3
19 5±3
dBm
dBm
dBm
dBm
dBm
dBm
dBm
dBm
716±3
814±3
912±4
10 10±4
11 8±4
12 6±4
13 4±4
14 2±5
15 0±5
dBm
dBm
dBm
dBm
dBm
dBm
dBm
dBm
dBm
2-2
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Operation Instruction and Installation
3.
Main Function
GSM Function Support
•
ARM926EJ-S Core
•
S20 Pin TA
•
No Java
•
Dual Band
•
Poly Ringtone(Midi,AMR,MP3)
•40
Non Camera
•
Phonebook
•
Bluetooth
•
(900/1800
500
2.0
MHz)
entry
Support
3-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Array course control
4.
Software Adjustments
4-1.
Test Jig(GH99
RF Test Cable(GH
-36900
39-00985
A)
A)
Test Cable(GH
Adapter(GH
39-01160
99-38251
A)
A)
4-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Array course control
Software Downloading
4-2.
4-2-1.
•2
4-2-2.
•
•
•
•
•
•
Downloading Binary Files
binary files for downloading E1360B.
E1360BDBxx.cla
–
E1360BDBxx.tfs
–
Pre-requsite for Downloading
Downloader Program(Gaia Downloader for SEC v00.exe
E1360B Mobile Phone
JIG BOX
Test Cable
Serial Cable
Binary files
)
4-2
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Array course control
4-2-3.
1.
S/W Downloader Program
Load the binary download program by executing the“Gaia Downloader for
SEC v00.exe
”.
Select the Port, Baud Rate and Mode
2.
.
4-3
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Array course control
Select the binary fileswhat you want to download
3.
4-4
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
ress the"Start" button and connect the Handset.
4. P
ThenPress the"Download" butto
n.
Array course control
4-5
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Exploded View and Parts List
5.
5-1.
QMW01
QFU01
QSP01
QMO01
QLC01
Cellular phone Exploded View
QFR01
QCR97
QKP01
QCR72
QME01
QKP02
QMP01
QME02
QMI01
QSH01
QAN02
QPC01
QFL00
QCR72
QSC05
QHI02
QHI01
QFL01
QRE01
QIF01
QCR67
QBA01
QBA00
5-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Exploded View and Parts List
5-2.
Cellular phone Parts list
Design LOC Description SEC CODE
QAN02 INTENNA-GTE1360S GH42-01873A
QBA00 PMO COVER-BATTERY GH72-51698A
QBA01 INNER BATTERY PACK-800MAH,BLK,UNI,MAIN GH43-03241A
QCR67 SCREW-MACHINE
QCR72 SCREW-MACHINE
QCR97 SCREW-MACHINE
6001-002083
6001-002051
6001-002262
QFR01 ASSY CASE-FRONT GH98-11378A
QFU01 ASSY CASE-SLIDE UPPER GH98-11377A
QKP01 ASSY KEYPAD-MAIN(ZK/XEN) GH98-11384A
QKP02 ASSY KEYPAD-NAVI(ZK/XEN) GH98-11383A
QLC01 ELA ETC-GTE1360S LCD HOT BAR SVC GH96-03828A
QME01 DOME SHEET-GTE1360S_MAIN GH59-06792A
QME02 DOME SHEET-GTE1360S_SUB GH59-06793A
QMI01 MICROPHONE-ASSY-GTE1360S GH30-00564A
QMO01 MOTOR DC-SGHT539 GH31-00328A
QMP01 ASSY PBA MAIN-GT_E1360B GH92-05384A
QMW01 PMO WINDOW-MIAN(ORANGE) GH72-53722A
QPC01 ASSY ETC-GT_E1360B SLIDE FPCB GH59-07499A
QSC05 TAPE-LOWER SCREW CAP GH74-43700A
QSH01 ASSY COVER-SHIELD CAN GH98-11385A
QSP01 SPEAKER
3001-002467
QFL00 ASSY HINGE-LOWER GH98-11380A
QFL01 ASSY CASE-SLIDE LOWER GH98-11381A
QHI01 ASSY HINGE-BASE GH98-11382A
QHI02 ASSY HINGE-PUSH ROD GH98-10706A
QRE01 ASSY CASE-REAR GH98-11379A
QIF01 PMO COVER-IF GH72-52313A
5-2
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Main Electrical Parts List
6.
Design LOC SEC Code Description
R105,R134,R222,R415 0202-001602 PB-SHORT-1005
D200,D201 0401-001110 DIODE-SWITCHING
ZD200,ZD300 0403-001547 DIODE-ZENER
ZD400 0406-001223 DIODE-TVS
D302,D303 0406-001286 DIODE-TVS
D304,D305 0406-001288 DIODE-TVS
LED300,LED301,LED302 0601-002591 LED
LED303 0601-002591 LED
U302 1001-001546 IC
TR400 1003-001440 IC
U305 1009-001037 IC
UME300 1108-0002
PAM100 1201-002731 IC
U102 1203-005362 IC
U201 1203-005498 IC
U306 1203-005512 IC
U103 1205-003322 IC
UCP200 1205-003662 IC
TH200 1404-001221 THERMISTOR
VR300,VR301,VR400 1405-001082 VARISTOR
C137,C341,VR100 1405-001167 VARISTOR
R111,R326 2007-000138 R-CHIP
R303 2007-000139 R-CHIP
R301,R311,R329,R330 2007-000141 R-CHIP
R221,R321 2007-000148 R-CHIP
R209 2007-000162 R-CHIP
R207,R309,R310,R312 2007-000172 R-CHIP
R313,R314,R315 2007-000172 R-CHIP
R306,R322 2007-000173 R-CHIP
R108 2007-001288 R-CHIP
R206 2007-001301 R-CHIP
R109,R110 2007-001313 R-CHIP
R414 2007-001333 R-CHIP
R400 2007-003025 R-CHIP
R203 2007-007698 R-CHIP
R210 2007-008500 R-CHIP
C336,C337 2203-000330 C-CERAMIC,CHIP
20 MEMORY
6-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Main Electrical Parts List
Design LOC SEC Code Description
C327,C330,C332 2203-000386 C-CERAMIC,CHIP
C117,C338,C339,C340 2203-000425 C-CERAMIC,CHIP
C203,C229 2203-000438 C-CERAMIC,CHIP
C215,C231,C307,C308 2203-000585 C-CERAMIC,CHIP
C309 2203-000585 C-CERAMIC,CHIP
C303,C305,C306 2203-000679 C-CERAMIC,CHIP
C111,C226 2203-000812 C-CERAMIC,CHIP
C400,C401,C404,C405 2203-000812 C-CERAMIC,CHIP
C406,C407,C408,C410 2203-000812 C-CERAMIC,CHIP
C411,C412,C414,C415 2203-000812 C-CERAMIC,CHIP
C416,C419,C420,C421 2203-000812 C-CERAMIC,CHIP
C422,C423,C424,C425 2203-000812 C-CERAMIC,CHIP
C426 2203-000812 C-CERAMIC,CHIP
C100,C300 2203-000995 C-CERAMIC,CHIP
C319,C320,C321,C322 2203-001153 C-CERAMIC,CHIP
C112,C113,C115,C116 2203-001385 C-CERAMIC,CHIP
C135 2203-001385 C-CERAMIC,CHIP
C217 2203-002443 C-CERAMIC,CHIP
C202,C205,C213,C219 2203-002709 C-CERAMIC,CHIP
C228,C230,C314,C315 2203-002709 C-CERAMIC,CHIP
C326,C329,C333 2203-003054 C-CERAMIC,CHIP
C114 2203-005057 C-CERAMIC,CHIP
C107 2203-005344 C-CERAMIC,CHIP
C134 2203-005382 C-CERAMIC,CHIP
C302,C304,C328,C331 2203-005482 C-CERAMIC,CHIP
C310,C403,C418 2203-006048 C-CERAMIC,CHIP
C206,C221 2203-006137 C-CERAMIC,CHIP
C200,C214 2203-006208 C-CERAMIC,CHIP
C120,C121,C123,C126 2203-006260 C-CERAMIC,CHIP
C127,C128,C129,C132 2203-006260 C-CERAMIC,CHIP
C222,C313 2203-006348 C-CERAMIC,CHIP
C207,C209,C210,C211 2203-006399 C-CERAMIC,CHIP
C212,C317 2203-006399 C-CERAMIC,CHIP
C119,C220,C316,C318 2203-006562 C-CERAMIC,CHIP
C417,C427 2203-006562 C-CERAMIC,CHIP
C110,C323 2203-006681 C-CERAMIC,CHIP
C201,C216 2203-006824 C-CERAMIC,CHIP
6-2
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Main Electrical Parts List
Design LOC SEC Code Description
C118 2203-006872 C-CERAMIC,CHIP
C204,C227 2404-001381 C-TA,CHIP
TA100 2404-001415 C-TA,CHIP
TA300 2404-001465 C-TA,CHIP
L107 2703-001178 INDUCTOR-SMD
L315,L316,L317,L318 2703-001723 INDUCTOR-SMD
L319 2703-001723 INDUCTOR-SMD
L105 2703-002170 INDUCTOR-SMD;
L202 2703-002176 INDUCTOR-SMD
L400,L401 2703-002201 INDUCTOR-SMD
L104 2703-002203 INDUCTOR-SMD
L103 2703-002204 INDUCTOR-SMD
L109 2703-002208 INDUCTOR-SMD
L310,L311,L313 2703-002313 INDUCTOR-SMD
L309,L312 2703-002365 INDUCTOR-SMD
L106 2703-002506 INDUCTOR-SMD
L201 2703-003297 INDUCTOR-SMD
OSC200 2801-003856 CRYSTAL
OSC201 2801-004769 CRYSTAL
F101 2903-001394 FILTER
F100 2904-001792 FILTER-SAW
L200 3301-001158 CORE-FERRITE BEAD
L314 3301-001342 CORE-FERRITE BEAD
L402 3301-001534 CORE-FERRITE BEAD
L203,L301,L302,L303 3301-001756 CORE-FERRITE BEAD
L304,L305,L306 3301-001756 CORE-FERRITE BEAD
L307,L308 3301-001812 CORE-FERRITE BEAD
RFS100 3705-001503 CONNECTOR-COAXIAL
SIM400 3709-001447 CONNECTOR-CARD EDGE
IFC300 3710-002683 CONNECTOR-SOCKET
HDC400 3711-005581 CONNECTOR-HEADER
BTC200 3711-006228 CONNECTOR-HEADER
ANT102 4202-001463 BT ANTENNA
Please consult the GSPN website (Samsung Portal) for the most recent version of the product's part list.
6-3
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Block Diagrams
SLAVEON
SLAVEON
7.
7-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
SLAVEON
SLAVEON
PNX4902
RF/IF
Tranceiver
PMU
IIC
Interface/RTC
Basic Charging
SIM Interface
Charging Controller
MEMORY
Nor/UtRAM
(
K5N2866ATB-
AT80)
128/64
MB
LCD
1.77"
CSTN-LCD
Battery
800
mA
KEY PAD
AUDIO MIC
--------------Ear MIC
SP
K
&
EARSPK
7-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
PCB Diagrams
8.
8-1.
Main Top
□
8-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
PCB Diagrams
8-2.
Main Bottom
8-2
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Loading...