Dishwasher
user manual
DW-FN320T
DW-FN320W
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
DD81-01446F-03_EN.indd 1DD81-01446F-03_EN.indd 1 2014-11-12 12:21:302014-11-12 12:21:30
Safety information
Please read this User Information carefully and keep it to refer to at a later date.
Pass it on to any subsequent owner of the appliance.
This manual contains sections of Safety Instructions, Part and Features,
Installation your dishwasher and Troubleshooting etc.
Carefully reading it before using the dishwasher will help you to use and maintain
the dishwasher properly.
The manufacturer, following a policy of constant development and up-dating of the product, may make
modifications without giving prior notice.
WARNING: When using your dishwasher, follow the below basic precautions including the following:
PROPER USE
• Do not abuse, sit on, or stand on the door or dish rack of the dishwasher.
• Do not operate your dishwasher unless all enclosure panels are properly in place. Open the door very
carefully if the dishwasher is operating. There is a risk of water squirting out.
• Do not place any heavy objects of stand on the door when it is open. The appliance could tip forward.
• When loading items to be washed:
- Locate sharp items so that they are not likely to damage the door seal;
- Load sharp knives with the handles up to reduce the risk of cut-type injuries;
• Warning : knives and other utensils with sharp points must be loaded in the basket with their points
down or placed in a horizontal position.
• Check that the detergent receptacle is empty after completion of the wash cycle.
• Do not wash plastic items unless they are marked dishwasher safe or the equivalent. For plastic items
not so marked, check the manufacturer’s recommendations.
• Use only detergent and rinse additives designed for an automatic dishwasher. Never use soap, laundry
detergent, or hand washing detergent in your dishwasher.
• Other means for disconnection from the supply must be incorporated in the fixed wiring with at least 3
mm contact separation in all poles.
• Keep children away from detergent and rinse aid, keep children away from the open door of the
dishwasher, there could still be some detergent left inside.
• Young children should be supervised to ensure that they do not play with the appliance.
• The appliance is not intended for use by young children or infirm persons without supervision.
• Dishwasher detergents are strongly alkaline. They can be extremely dangerous if swallowed. Avoid
contact with skin and eyes and keep children away from the dishwasher when the door is open.
• The door should not be left in the open position since this could present a tripping hazard.
• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard.
• Please dispose of packing materials properly.
• Use the dishwasher only for its intended function.
• During installation, the power supply must not be excessively or dangerously bent or flattened.
• Do not tamper with controls.
• The appliance is to be connected to the water mains using new hose sets and the old hose-sets should
not be reused.
READ AND FOLLOW THIS SAFETY INFORMATION
CAREFULLY SAVE THESE INSTRUCTIONS
2_ safety information
DD81-01446F-03_EN.indd 2DD81-01446F-03_EN.indd 2 2014-11-12 12:21:382014-11-12 12:21:38
DISPOSAL
Dispose of the dishwasher packaging material correctly.
All packaging materials can be recycled.
Plastic parts are marked with the standard international abbreviations:
PE for polyethylene, e.g. sheet wrapping material
PS for polystyrene, e.g. padding material
POM polyoxymethylene, e.g. plastic clips
PP polypropylene, e.g. Salt filler
ABS Acrylonitrile Butadiene Styrene, e.g. Control Panel.
WARNING: Packaging material could be dangerous for children!
For disposing of package and the appliance please go to a recycling centre. Therefore cut o the
power supply cable and make the door closing device unusable.
Cardboard packaging is manufactured from recycled paper and should be disposed in the waste
paper collection for recycling.
By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product.
For more detailed information about recycling of this product, please contact your local city oce and
your household waste disposal service.
INSTRUCTION ABOUT THE WEEE MARK
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its
electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other
household waste at the end of their working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate these items from other types of
waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or
their local government offi ce, for details of where and how they can take these items for
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product and its electronic accessories should not be mixed with other
commercial wastes for disposal.
READ AND FOLLOW THIS SAFETY INFORMATION
CAREFULLY SAVE THESE INSTRUCTIONS
safety information _3
DD81-01446F-03_EN.indd 3DD81-01446F-03_EN.indd 3 2014-11-12 12:21:382014-11-12 12:21:38
Contents
PART AND FEATURES
5
INSTALLING YOUR DISHWASHER
8
USING THE DETERGENT AND WATER
SOFTENER
11
LOADING THE DISHWASHER RACKS
18
WASHING PROGRAMMES
22
5 Dishwasher features
6 Control panel
7 Displays
9 Water supply and drain
10 Connection of drain hoses
10 Position the appliance
10 Start of dishwasher
11 Water softener
12 Loading the salt into the softener
13 Fill the rinse aid dispenser
15 Function of detergent
17 How to use the 3 in 1 option
18 Loading the upper basket
19 Loading the lower basket
19 Folding spikes of lower basket
20 Cutlery(silverware) basket
21 For washing in the dishwasher the following
cutlery/dishes
22 Turning on the appliance
22 Change the program...
23 At the end of the wash cycle
23 Wash cycle table
CLEANING AND CARE
24
TROUBLESHOOTING
24 Cleaning the filters
25 Cleaning the spray arms
25 Cleaning the door
25 Caring for the dishwasher
25 Protect against freezing
26 How to keep your dishwasher in shape
27 Before calling for service
29 Error codes
27
APPENDIX
30 Specifications
30 Product dimension
30
4_ safety information
DD81-01446F-03_EN.indd 4DD81-01446F-03_EN.indd 4 2014-11-12 12:21:382014-11-12 12:21:38
Part and features
DISHWASHER FEATURES
Front & Rear view
01 PART AND FEATURES
1
2
3
4
5
1 Upper Basket 4 Salt Container 7 Spray arms 10 Drain hose
2 Duct nozzle 5 Dispenser 8 Filter assembly
3 Lower Basket 6 Cup Shelf 9 hose
Accessory parts - User manual, Salt funnel, cutlery basket.
6
7
8
9
10
part and features _5
DD81-01446F-03_EN.indd 5DD81-01446F-03_EN.indd 5 2014-11-12 12:21:382014-11-12 12:21:38
Part and features
CONTROL PANEL
1 5 6
4
3 2 8
1 POWER BUTTON Press this button to turn on your dishwasher: the screen lights up.
2 3 IN 1 OPTION BUTTON
3 DELAY START BUTTON
4 CHILD LOCK BUTTON
5 DISPLAY WINDOW Running indicator, delay time, error codes and etc.
To select 3 in 1 option which needs not salt and rinse aid but a 3 In1
tablet. This option can be selected on Intensive, Auto or Eco program
only.
Press this button to set the delayed hours for washing. You can delay
the start of washing up to 24 hours. One press on this button delays
the start of washing by one hour.
This option allows you to lock the buttons on the control panel so
children cannot accidentally start the dishwasher by pressing the
buttons on the panel.
To lock and unlock the buttons on the control panel, hold down both
the 3 in 1 and Delay start buttons for three (3) seconds.
7
6 PROGRAM BUTTON To select washing program press the button.
In Power on condition, close the dishwasher door and select the cycle
and desired options. Press the Start/Pause button to begin the cycle.
7 START/PAUSE BUTTON
8 HALF LOAD BUTTON
• When the door is open only the Power button will operate.
• You can select options (3 in 1, Delay start and/or Half load) before starting a cycle.
IMPORTANT: To get the best performance from your dishwasher, read all the operating instructions
before using it for the first time.
When you want to pause the dishwasher while running, press the
Start/Pause button and make sure to open the door slowly and
carefully. You can reset the machine by pressing the Start/Pause
button for 3 seconds during washing. After reset, the dishwasher goes
to the initial state except salt consumption setting of water softener.
To select Half load function. (With this Half load function you can only
use it when you have only about or less than 6 place setting dishware,
and you will see less water and energy consumption. It can only be
used with Intensive, Auto, Eco and Delicate.)
6_ part and features
DD81-01446F-03_EN.indd 6DD81-01446F-03_EN.indd 6 2014-11-12 12:21:382014-11-12 12:21:38
DISPLAYS
2
1 PROGRAM ICON When press the Program button, each program is selected.
2 3*8 SEGMENT Display the remaining time, error code, or delay time.
RINSE AID INDICATOR
3 IN 1 ICON When select 3 in 1 option.
SALT INDICATOR
CHILD LOCK ICON When select Child lock function.
HALF LOAD ICON When select Half load option.
WATER INLET
INDICATOR
When rinse aid is needed refill, this indicator is on. Refill the rinse aid
to dispenser.
When salt is needed refill, this indicator is on. Refill the salt to water
softener.
When occur water inlet problem. Check the water faucet or water inlet
hose.
1
01 PART AND FEATURES
part and features _7
DD81-01446F-03_EN.indd 7DD81-01446F-03_EN.indd 7 2014-11-12 12:21:392014-11-12 12:21:39
Installing your dishwasher
WARNING : Electrical shock hazard
Disconnect electrical power before installing dishwasher.
Failure to do so could result in death or electrical shock.
ATTENTION: The installation of the pipes and electrical equipments should be done by professionals.
About electricity connecting
CAUTION, for personal safety:
DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD GROUNDING
PRONG FROM THE POWER CORD.
Electrical requirements
• An AC 220-240 V / 50 Hz fuse or a circuit breaker.
• An individual branch circuit serving your dishwasher.
Grounding instructions
Insure proper ground exists before use
This appliance must be grounded. In the event of a malfunction or breakdown, grounding
will reduce the risk of electric shock by providing a path of least resistance of electric
current. This appliance is equipped with a cord having an equipment-grounding conductor
and a grounding plug. The plug must be plugged into an appropriate outlet that is installed
and grounded in accordance with all local codes and ordinances.
WARNING: Improper connection of the equipment grounding conductor can result in the
risk of an electric shock. Check with a qualified electrician or service representative if you
are in doubt whether the appliance is properly grounded. Do not modify the plug provided
with the appliance.
8_ installing your dishwasher
DD81-01446F-03_EN.indd 8DD81-01446F-03_EN.indd 8 2014-11-12 12:21:392014-11-12 12:21:39
WATER SUPPLY AND DRAIN
Cold water connection
Connect the cold water supply hose to a threaded 3/4 (inch) connector
and make sure that it is fastened tightly in place.
If the water pipes are new or have not been used for an extended period
of time, let the water run to make sure that the water is clear and free of
impurities. If this precaution is not taken, there is a risk that the water inlet
can get blocked and damage the appliance.
Provided water supply hose has the aqua-safe system. Ensure that
water supply hose’s aqua-safe pipe is connected to the faucet.
Hot water connection
The water supply to the appliance can also be connected to the house hot water line (centralized
system, heating system), as long as it does not exceed a temperature of 60 °C. In this case, the
wash cycle time will be shortened by about 15 minutes and the wash eciency slightly reduced.
The connection must be made to the hot water line following the same procedures as those for
the connection to the cold water line.
Positioning the appliance
Position the appliance in the desired location. The back should rest against the wall behind
it, and the sides, along the adjacent cabinets or wall. The dishwasher is equipped with
water supply and drain hoses that can be positioned to the right or the left to facilitate
proper installation.
How to drain excess water from hoses
If the sink is 1000mm higher from the floor, the excess water in hoses cannot be drained directly
into the sink. It will be necessary to drain excess water from hoses into a bowl or suitable
container that is held outside and lower than the sink.
02 INSTALLING
Water outlet
Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks.
Ensure that the water inlet hose is not kinked or squashed.
Extension hose
If you need a drain hose extension, Use a similar size and quality drain hose.
It must be no longer than 4 metres; otherwise the cleaning eect of the dishwasher could be
reduced.
Syphon connection
The waste connection must be at a height of between 40 cm (minimum) and 100 cm (maximum)
from the bottom of the dishwasher. The water drain hose should be fixed by a hose clip.
Aqua-safe
The Aqua-safe System is a safety valve system, preventing water leaks. If the water inlet hose
starts to leak anytime, the safety valve cuts o the running water. If the water inlet hose or the
safety valve is damaged, remove & replace it.
Do not enlarge or shorten the inlet hose.
installing your dishwasher _9
DD81-01446F-03_EN.indd 9DD81-01446F-03_EN.indd 9 2014-11-12 12:21:392014-11-12 12:21:39
Installing your dishwasher
CONNECTION OF DRAIN HOSES
Insert the drain hose into a drain pipe with a minimum diameter of 4cm, or let it run into the sink, making
sure to avoid bending or crimping it. The top of the hose must be at a height between 40 and 100 cm. The
free end of the hose must not be immersed in water to avoid the back flow of it.
Counter
NOTE
The top of the hose must
be at a height between 40
and 100cm.
The free end of the hose
must not be immersed in
water.
Drain pipe
Min. 400 mm
40 mm
Max 1000 mm
POSITION THE APPLIANCE
Position the appliance in the desired location. The back should rest against the wall behind it, and the sides,
along the adjacent cabinets or walls. The dishwasher is equipped with water supply and drain hoses that
can be positioned either to the right or the left sides to facilitate proper installation.
Levelling the Appliance
Once the appliance is positioned for levelling, the height of the
dishwasher may be altered via adjustment of the screwing level of the
feet. In any case, the appliance should not be inclined more than 2°.
START OF DISHWASHER
The followings should be checked before starting the dishwasher.
1. the dishwasher is level and fixed.
2. the inlet valve is opened.
3. there leakage at the connections of the conducts.
4. the wires are tightly connected.
5. the power is switched on.
6. the inlet and drain hoses are not knotted.
7. All packing materials and printings should be taken out from the dishwasher.
ATTENTION: After installation please put this manual in a safe place. The contents of this manual can
be useful to users.
10_ installing your dishwasher
DD81-01446F-03_EN.indd 10DD81-01446F-03_EN.indd 10 2014-11-12 12:21:392014-11-12 12:21:39
Using the detergent and water
softener
WATER SOFTENER
The water softener must be set manually, using the water hardness dial.
The water softener is designed to remove minerals and salts from the water, which would have a detrimental
or adverse eect on the operation of the appliance. The higher the content of these minerals and salts, the
harder your water is. The softener should be adjusted according to the hardness of the water in your area.
Your local Water Authority can advise you on the hardness of the water in your area.
Adjusting salt consumption
The dishwasher is designed to allow for adjusting the amount of salt consumed based on the
hardness of the water used. This is intended to Spelling - optimise - customise the level of salt
consumption so that the salt consumption could be set proceed as follows:
1. Switch on the appliance;
2. Press the Start/Pause button for more than 3 seconds to start the water softener set model
within 60seconds after the appliance was switched on;
3. Press the Start/Pause button to select the proper set according to your local environment,
the sets will change in the following sequence: H1->H2->H3->H4->H5->H6; It is
recommended that adjustments should be made in accordance with the following table.
* The manufactory setting: H4 (EN 50242)
4. Wait for 5 seconds to end the set up model.
WATER HARDNESS
º dH º fH º Clark mmol/l
0~5 0~9 0~6 0~0.94 H1 0 /
6~11 10~20 7~14 1.0~2.0 H2 20 60
12~17 21~30 15~21 2.1~3.0 H3 30 50
18~22 31~40 22~28 3.1~4.0 H4 40 40
23~34 41~60 29~42 4.1~6.0 H5 50 30
35~55 61~98 43~69 6.1~9.8 H6 60 20
1 dH (German degree) = 0.178 mmol/l
1 Clark (British degree) = 0.143 mmol/l
1 fH (French degree) = 0.1 mmol/l
Contact your local water board for information on the hardness of your water supply.
WATER SOFTENER
The hardness of the water varies from place to place. If hard water is used in the
dishwasher, deposits may form on dishes and utensils. The appliance is equipped with a
special softener that uses a salt specifically designed to eliminate lime and minerals from the
water.
Selector Position
Salt consumption
(gram/cycle)
Autonomy
(cycles/1 kgs)
03 DETERGENT AND WATER SOFTENER
using the detergent and water softener _11
DD81-01446F-03_EN.indd 11DD81-01446F-03_EN.indd 11 2014-11-12 12:21:392014-11-12 12:21:39
Using the detergent and water
softener
LOADING THE SALT INTO THE SOFTENER
Always use salt intended for use with dishwasher.
The salt container is located beneath the lower rack and should be filled as follows:
ATTENTION
• Only use salt specifically designed for use in dishwashers! All other types of salt not specifically
designed for use in a dishwasher, especially table salt, will damage the water softener. In case of
damages caused by the use of unsuitable salt the manufacturer does not give any warranty nor is
liable for any caused damages.
• Only fill with salt just before starting one of the complete washing programs. This will prevent any
grains of salt or salty water, which may have been split, remaining of the bottom of the machine for
any period of time, which may cause corrosion.
• After the first wash cycle the control panel light expires.
1. Remove the lower basket and then unscrew and remove the cap from
the salt container.
Open
2. If you are filling the container for the first time, fill 2/3 of its volume with water (around 1 liter).
3. Place the end of the funnel (supplied) into the hole and introduce about
1,5 kg of salt. It is Normal for a small amount of water to come out of
the salt container.
4. Carefully screw the cap back on.
5. Usually, the salt warning light will be o after the salt container be filled with salt.
• The salt container must be refilled when the salt warning light in the control panel comes on.
Though the salt container is filled enough, the indicator light may not light may not switch o until
the salt fully dissolves.
If there is no salt warning light in the control panel, you can judge when to load the salt into the
softener by the cycles that the dishwasher has run.
• If a lot of salt is spilt inside the dishwasher run a pre wash program to clan the spillage.
12_ using the detergent and water softener
DD81-01446F-03_EN.indd 12DD81-01446F-03_EN.indd 12 2014-11-12 12:21:392014-11-12 12:21:39
FILL THE RINSE AID DISPENSER
Function of rinse aid
Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and
streak free drying.
ATTENTION: Only use branded rinse aid for dishwasher. Never fill the rinse aid dispenser
with any other substances (e.g. dishwasher cleaning agent, liquid detergent). This would
damage the appliance.
When to refill the rinse aid dispenser
If there is no rinse-aid warning light in the control panel, you can judge the amount of rinse-aid by
the Colour of the optical level indicator “D” located next to the cap. When the rinse-aid container
is full, the whole indicator will be dark. As the rinse-aid diminishes, the size of the dark dot
decreases. You should never let the rinse aid get below 1/4 full.
As the rinse aid diminishes, the size of the black dot
on the rinse aid level indicator changes, as illustrated
below.
Full
3/4 full
1/2 full
1/4 full : Should refill to eliminate spotting
Empty
03 DETERGENT AND WATER SOFTENER
D (Rinse-Aid indicator)
using the detergent and water softener _13
DD81-01446F-03_EN.indd 13DD81-01446F-03_EN.indd 13 2014-11-12 12:21:392014-11-12 12:21:39
Using the detergent and water
softener
Rinse Aid dispenser
1. To open the dispenser, turn the cap to the “open” (left) arrow
and lift it out.
2. Pour the rinse aid into the dispenser, being careful not to
overfill.
3. Replace the cap by inserting it aligned with “open” arrow
and turning it to the closed (right) arrow.
The rinse aid is released during the final rinse to prevent water from forming droplets on your
dishes that can leave spots and streaks. It also improves drying by allowing water to water to run
o the dishes.
Your dishwashers is designed to use liquid rinse aids. The rinse aid dispenser is located inside
the door next to the detergent dispenser. To fill the dispenser, open the cap and pour the rinse
aid into the dispenser until the level indicator turns completely black. The volume of the rinse aid
container is about 130 ml.
Be careful not to overfill the dispenser, because this could cause over sudsing. Wipe away any
spills with a damp cloth. Don’t forget to replace the cap before you close dishwasher door.
ATTENTION: Clean up any rinse aid spilt during filling with an absorbent cloth to avoid
excess foaming during the next wash.
Adjusting rinse aid dispenser
The rinse aid dispenser has four settings. Always start with the
dispenser set on “3”. If spots and poor drying are problems,
increase the amount of rinse aid dispensed by removing the
dispenser lid and rotating the dial to “4”. We suggest you to set
on “3” (Factory value is “3”).
Increase the dose if there are drops of water or lime spots on the dishes after washing.
Reduce it if there are sticky whitish streaks on the dishes or a bluish film on glassware or
knife blades.
14_ using the detergent and water softener
DD81-01446F-03_EN.indd 14DD81-01446F-03_EN.indd 14 2014-11-12 12:21:402014-11-12 12:21:40
FUNCTION OF DETERGENT
Push latch to open
Detergents with its chemical ingredients are necessary to remove dirt, crush dirt and transport it out of the
dishwasher. Most of commercial quality detergents are suitable for this purpose.
WARNING: Dishwasher detergent is corrosive! Take care to keep it out of reach of children.
Proper Use of Detergent
Use only detergent specifically made for use in dishwashers. Keep your detergent fresh and dry. Don’t
put powder detergent into the dispenser until you’re ready to wash dishes.
Concentrated detergent
Based on their chemical composition, dishwasher detergent can be split in two basic types:
• conventional, alkaline detergents with caustic components
• low alkaline concentrated detergents with natural enzymes
The use of “normal” washing programmes in conjunction with concentrated detergents reduces
pollution and is good for your dishes; these wash programmes are specially matched to the
dirt-dissolving properties of the enzymes of the concentrated detergent. For this reason “normal”
wash programmes in which concentrated detergents are used can achieve the same results that
can otherwise only be achieved using “intensive” programmes.
Detergent tablets
Detergent tablets of dierent brands dissolve at dierent speeds. For this reason some detergent
tablets cannot dissolve and develop their full cleaning power during short programmes.
Therefore please use long programmes when using detergent tablets, to unsure the complete
removal of detergent residuals.
Detergent dispenser
The dispenser must be refilled before the start of each wash cycle following the instructions
provided in the Wash Cycle Table. Your dishwasher uses less detergent and rinse aid then
conventional dishwashers. Generally, only one tablespoon of detergent is needed for a normal
wash load. Also, more heavily soiled items need more detergent. Always add the detergent just
before starting the dishwasher, otherwise it could get damp and will not dissolve properly.
03 DETERGENT AND WATER SOFTENER
Fill the detergent in dispenser
1. If the lid is closed: press release button. The lid springs
open.
Push latch to open
2. Always add the detergent just before starting each
wash cycle. Only use branded detergent aid for
dishwasher.
DD81-01446F-03_EN.indd 15DD81-01446F-03_EN.indd 15 2014-11-12 12:21:402014-11-12 12:21:40
using the detergent and water softener _15
Using the detergent and water
softener
Amount of detergent to use
1. Fill the detergent dispenser with detergent.
The marking indicates the dosing levels, as illustrated on
right:
A. This section is for main wash detergent, approximately
25g
B. This section is for the pre wash detergent,
approximately 5g
If the dishes are heavily soiled, place an additional
detergent dose in the pre-wash detergent chamber. This
detergent will take eect during the pre-wash phase.
You can find information about the amount of detergent
for the single programmes on the “Wash cycle table”.
(See page 23)
Please be aware, that according to the soiling level and
the specific hardness of water dierences are possible.
2. Close the lid and press until it locks in place.
Please observe the manufacturers dosing and storage recommendations as stated on the
detergent packaging.
Detergents
There are 3 sorts of detergents.
1. With phosphate and with chlorine.
2. With phosphate and without chlorine.
3. Without phosphate and without chloride.
Normally new pulverised detergent is without phosphate. The water softener function of
phosphate is not given. In this case we recommend to fill salt in the salt container even when the
hardness of water is only 6 dH. If detergents without phosphate were used in case of hard water
often white spots appear at dishes and glasses. In this case please add more detergent to reach
better results. Detergents without chlorine do only bleach a little. Strong and coloured spots will
not removed completely. In this case please choose a programme with higher temperature.
A
B
16_ using the detergent and water softener
DD81-01446F-03_EN.indd 16DD81-01446F-03_EN.indd 16 2014-11-12 12:21:402014-11-12 12:21:40
HOW TO USE THE 3 IN 1 OPTION
Your dishwasher has a 3 in 1 option which does not need salt and rinse aid but a 3 In1 tablet. This option
can select on Intensive, Auto or Eco program only.
The 3 in 1 setting is only for use with 3 in 1 tablets. If using 3 in 1 tablet without this option, the
appliance will not get it’s best performance.
1. Put the 3 in 1 tablet into the container then start the 3 in 1 option.
2. Close the lid and press until it locks in place.
When using 3 in 1 compact combination detergents ensure that
the lid can be closed correctly.
ATTENTION: Keep all detergents in a safe place out of
children’s reach. Always add the detergent in the dispenser just
before starting the dishwasher.
03 DETERGENT AND WATER SOFTENER
using the detergent and water softener _17
DD81-01446F-03_EN.indd 17DD81-01446F-03_EN.indd 17 2014-11-12 12:21:402014-11-12 12:21:40
Loading the dishwasher racks
For best performance of the dishwasher, follow these loading guidelines.
Features and appearance of racks and silverware baskets may vary from your
model.
Attention before or after loading the dishwasher racks
Scrape o any large amounts of leftover food. It is not necessary to rinse the dishes under running
water. Place objects in the dishwasher in the following order:
1. Items such as cups, glasses, pots/pans, etc. are stood upside down.
2. Curved items, or those with recesses, should be at a slant so that water can run o.
3. They are stacked securely and can not tip over.
4. They do not prevent the spray arms from rotating while washing takes place.
Very small items should not be washed in the dishwasher as they could easily fall out of the racks.
Removing the dishes
To prevent water dripping from the upper basket into the lower basket, we recommend that you empty
the lower basket first and then the upper basket.
LOADING THE UPPER BASKET
The upper basket is designed to hold more delicate and lighter dishware such as glasses, coee and tea
cups and saucers, as well as plates, small bowls and shallow pans (as long as they are not too dirty).
Position the dishes and cookware so that they will not get moved by the spray of water. Always place
glasses, cups & bowls upside down.
1
4
3
IN
5
6
1
2
1
3
3
3
1
Cups
1
2
Saucers
5
3
Glasses
4
Small serving bowl
Medium serving bowl6Large serving bowl
Adjusting the Upper Basket
The height of the upper basket can be adjusted in order to create more space for large utensils
both for the upper/lower basket.
1. To lower the upper rack, press the “A”
levers located at the left and right sides
of the upper basket and push the upper
basket downwards slightly at the same
time.
2. To raise the upper rack, just pull the
upper basket upwards without operating
any levers.
Caution: We recommend adjusting
the height of the upper basket before
loading dishes into the basket. If you
adjust the the basket after loading the
dishes, you may damage the dishes.
18_ loading the dishwasher racks
DD81-01446F-03_EN.indd 18DD81-01446F-03_EN.indd 18 2014-11-12 12:21:412014-11-12 12:21:41
A
To lower position To upper position
LOADING THE LOWER BASKET
We recommend that you place large items which are most dicult to clean in to the lower rack: pots, pans,
lids, serving dishes and bowls, as shown in the figure to the right.
It is preferable to place serving dishes and lids on the side of the racks in order to avoid blocking the
rotation of the top spray arm. Pots, serving bowls, etc. must always be placed top down.
Deep pots should be slanted to allow water to flow out.
The bottom rack feature fold down tine rows so that larger or more pots and pans can be loaded.
04 LOADING THE RACKS
7
IN
Dessert dishes
9
Soup plates
Long items, serving cutlery, salad servers and big knives should be placed on the shelf so that they do
not obstruct the rotation of the spray arms.
8
Dinner plates
10
Oval platter
IN
FOLDING SPIKES OF LOWER BASKET
For better stacking of pots and pans, the spikes can be folded down
as show in the picture right.
loading the dishwasher racks _19
DD81-01446F-03_EN.indd 19DD81-01446F-03_EN.indd 19 2014-11-12 12:21:432014-11-12 12:21:43
Loading the dishwasher racks
CUTLERY(SILVERWARE) BASKET
Silverware should be placed in the cutlery basket with handles at the bottom: The spoon should be loaded
individually into the appropriate slots, especially long utensils should be placed in the horizontal position at
the front of the upper basket.
1 Soup spoons 5 Dessert spoons
2 Forks 6 Serving spoons
3 Knives 7 Serving forks
4 Teaspoons 8 Gravy ladles
WARNING
• Do not let any item extend through the bottom.
• Always load sharp utensils with the sharp point down!
20_ loading the dishwasher racks
DD81-01446F-03_EN.indd 20DD81-01446F-03_EN.indd 20 2014-11-12 12:21:462014-11-12 12:21:46
FOR WASHING IN THE DISHWASHER THE FOLLOWING CUTLERY/
DISHES
Are not suitable Are of limited suitability
Cutlery with wooden, horn china or mother-of-pearl
handles.
Plastic items that are not heat resistant Older
cutlery with glued parts that is not temperature
resistant Bonded cutlery items or dishes Pewter
or cooper items Lead crystal glass Steel items
subject to rusting Wooden platters Items made from
synthetic fibres.
Do not try and wash items soiled with cigarette ash, candle wax, lacquer or paint. If you buy new
dishes please make sure that they are suitable for dishwashers.
Please do not overload your dishwasher. There is only space for 12 standard dishes. Do not use dish
that are not suitable for dishwashers. This is important for good results and for reasonable energy
consumption.
Some types of glasses can become dull after a
large number of washes.
Silver and aluminium parts have a tendency to
discolour during washing.
Glazed patterns may fade if machine washed
frequently.
When loading the dishes and cutlery
Dishes and cutlery must not impede the rotation of the spray arms.
Load hollow items such as cups, glasses, pans etc. with the opening downwards so that water
cannot collect in the container or a deep base.
Dishes and items of cutlery must not lie inside one another, or cover each other
• To avoid damage to glasses, they must not touch.
• Load large items which are most dicult to clean into the lower rack.
• The upper rack is designed to hold more delicate and lighter dishware such as glasses,
coee and tea cups.
ATTENTION
Long bladed knives stored in an upright position are a potential hazard!
Long and/or sharp items of cutlery such as carving knives must be positioned horizontally in
the upper basket.
04 LOADING THE RACKS
Damage to glassware and other dishes.
Possible causes Suggested remedy
• Type of glass or manufacturing process.
Chemical composition of detergent.
• Water temperature and duration of
dishwasher programme.
DD81-01446F-03_EN.indd 21DD81-01446F-03_EN.indd 21 2014-11-12 12:21:472014-11-12 12:21:47
• Use glassware or porcelain dishes that
have been marked dishwasher-proof by
the manufacturer
• Use a mild detergent that is described as
kind of dishes If necessary, seek further
information from detergent manufacturers.
• Select a programme with as low a
temperature.
• To prevent damage, take glass and cutlery
out of the dishwasher as soon as possible
after the programme has ended.
loading the dishwasher racks _21
Washing programmes
TURNING ON THE APPLIANCE
Starting a cycle wash
1. Draw out the lower and upper basket, load the dishes and push them back..
It is recommended to load the lower basket first, then the upper one (see the section entitled “Loading
the dishwasher racks”).
2. Pour in the detergent (see the section entitled “Using the detergent and water softener”).
3. Insert the plug into the socket. The power supply is 220-240 VAC/50 HZ, the specification of the socket
is 15A 250VAC. Make sure that the water supply is turned on to proper pressure.
4. Close the door, press the Power button, to switch on the machine.
5. Press the Program button, the wash program will be changed as follows direction:
Intensive Auto Eco Delicate Express Wash Pre Wash
If a wash program is selected, the response light will light. Then press the Start/Pause button, the
dishwasher begins to start.
When you press the Start/Pause button to pause during washing, the running indicator will stop
blinking and the dishwasher will beep every minute unless you press the Start/Pause button to start.
CHANGE THE PROGRAM...
Premise:
1. A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the
detergent may have already been released, and the appliance may have already drained the wash water.
If this is the case, the detergent dispenser must be refilled (see the section entitled “Fill the detergent in
dispenser”).
2. Press the Start/Pause button, the machine will be in standby state, press the Program button more
than 3 seconds then you can change the program to the desired cycle setting.
If you open the door during a wash cycle, the machine will pause. The program light will stop blinking
and the buzzer will beep every minute unless you close the door. After you close the door, the machine
will keep on working after 3 seconds automatically.
If your model has broken memory function, the machine will go on to finish the selected program after
the power cut.
Add a dish
A forgotten dish can be added at any time before the detergent dispenser opens.
1. Press the Start/Pause button and make sure to open the door slowly and carefully as there
is a possibility of injury from the hot steam inside the dishwasher.
2. After the spray arms stop working, you can open the door completely.
3. Add forgotten dishes.
4. Close the door. The dishwasher will work after 3 seconds.
WARNING: It is dangerous to open the door when washing, because the hot water may
scald you. If the door is opened while the dishwasher is running, a safety mechanism is
activated and stops the cycle.
22_ washing programmes
DD81-01446F-03_EN.indd 22DD81-01446F-03_EN.indd 22 2014-11-12 12:21:472014-11-12 12:21:47
AT THE END OF THE WASH CYCLE
When the working cycle has finished, the buzzer of dishwasher will beep shortly, then stop. In the digital
display appears “End”, only in this case the programme has ended.
1. Switch o the dishwasher by pressing the Power button.
2. Turn o the water tap!
Open the door carefully. Hot steam may escape when the door is opened!
• Hot dishes are sensitive to knocks. The dishes should be allowed to cool down around 15 minutes
before removing from the appliance.
• Open the dishwasher’s door, leave it ajar and wait a few minutes before removing the dishes. In
this way they will be cooler and the drying will be improved.
• Unloading the dishwasher.
It is normal that the dishwasher is wet inside.
Empty the lower basket first and then the upper one. This will avoid water dripping from the upper
basket onto the dishes in the lower one.
WASH CYCLE TABLE
Program Cycle
Intensive
Auto
Eco
(*EN 50242)
Delicate
Express
Wash
Pre Wash
Cycle selection
information
For the heaviest soiled
loads, such as pots, pans,
casserole dishes and dishes
that have been Sitting with
dried food on Them for a
while.
For all soiled loads, such as
pots, pans, casserole dishes
and dishes that have been
sitting with dried food on
them for a while.
For lightly soiled loads, such
as plates, glasses, bowls
and lightly soiled pans.
For normally soiled dishes or
fragile items such as glasses.
A shorter wash for lightly
soiled loads that do not
need drying.
For pre-cleaned dishes or
glasses. No detergent is
dispensed and no dry cycle
is initiated.
* EN 50242: This program is the test cycle. The information for comparability test in accordance with
EN 50242, as follows:;
• Capacity: 12 place setting
• Position of Upper Basket: to lower position
• Rinse aid setting: 3
Description of
Cycle
Pre-Wash (50 °C)
Pre-Wash
Wash (65 °C)
Rinse
Rinse (55 °C)
Drying
Pre-Wash ( 40 °C )
Auto Wash ( 45 °C )
Rinse
Rinse ( 67 °C )
Drying
Pre-wash
Wash (49 °C)
Rinse
Rinse (62 °C)
Drying
Pre-wash
Wash (40 °C)
Rinse (60 °C)
Drying
Wash (40 °C)
Rinse
Rinse (45 °C)
Pre-Wash - 8 0.1 3.8
Detergent
pre/main
5/25 g
(or 3 in 1)
5/25 g
(or 3 in 1)
5/25 g
(or 3 in 1)
5/25 g 110 0.9 14.5
Running
time (min)
120~150 0.9~1.2 11~16
20 g 35 0.6 10.5
Energy
(Kwh)
160 1.4 17.5
175 1.03 12
Water (ℓ)
05 WASHING PROGRAMMES
washing programmes _23
DD81-01446F-03_EN.indd 23DD81-01446F-03_EN.indd 23 2014-11-12 12:21:472014-11-12 12:21:47
Cleaning and care
CLEANING THE FILTERS
Filtering system
For your convenience, we have placed the drain pump and filtering system within easy reach
inside the tub. There are three components of the filtering system: the main filter, the coarse filter,
and the fine filter.
1. Main filter: Food and soil particles trapped by this filter are
pulverized by a special jet on the lower spray arm and washed down
the drain.
2. Coarse filter: Larger items, such as pieces of bone or glass, that
could clog the drain are trapped in the coarse filter. To remove an
item caught in this filter, gently squeeze the tabs on top of this filter
and lift it out.
3. Fine filter: This filter holds soil and food residue in the sump area
and prevents it from being redeposited on the dishes during a cycle.
ATTENTION: Do not put the fine filter upside down.
Filter assembly
For best performance and results, the filter assembly must be cleaned. The filter eciently
removes food particles from the wash water, allowing it to be recirculated during the cycle.
For this reason, it is a good idea to remove the larger food particles trapped in the filter after
each wash cycle by rinsing the semicircular filter and cup under running water. To remove the
filter assembly, turn it in anti-clockwise direction and lift the filter assembly up. The entire filter
assembly should be cleaned regularly.
To clean the coarse filter and the fine filter, use a cleaning brush. Then, reinsert the entire
assembly in the dishwasher, positioning in its seat, pressing downward, turning it clockwise
direction.
2
1
3
Open
The dishwasher must never be used without the filters. Improper replacement of the filter may
reduce the performance level of the appliance and damage dishes and utensils.
WARNING: Never run the dishwasher without the filters in place. When cleaning the filters,
do not damage them. Otherwise the filters may not perform as intended and poor wash
results or damage to the internal parts may be encountered.
24_ washing programmes
DD81-01446F-03_EN.indd 24DD81-01446F-03_EN.indd 24 2014-11-12 12:21:472014-11-12 12:21:47
CLEANING THE SPRAY ARMS
It is necessary to clean the spray arms regularly as hard water chemicals may
clog the spray arm jets and bearings. To remove the middle spray arm, hold the
nut, rotate the arm clockwise to remove it. To remove the lower spray arm, pull
out the spray arm upward. Wash the arms in soapy and warm water and use a
soft brush to clean the jets. Replace them after rinsing them thoroughly.
Open
CLEANING THE DOOR
To clean the edge around the door, you should use only a soft warm, damp rag.
To prevent penetration of water into the door lock and electrical components,
do not use a spray cleaner of any kind.
Also, never use abrasive cleaners or scouring pads on the outer surfaces
because they will scratch the finish. Some papers towels can also scratch or
leave marks on the surface.
WARNING: Never use a spray cleaner to clvean the door panel for it could damage the door lock and
electrical components. It is not advised to use the abrasive agent or some paper towel because of the
risk of scratching or leaving spots on the stainless steel surface.
CARING FOR THE DISHWASHER
To clean the control panel use a lightly damp cloth then dry thoroughly. To clean the exterior use a good
appliance polish wax.
Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.
06 CLEANING AND CARE
PROTECT AGAINST FREEZING
If your dishwasher is left in an unheated place during the winter:
1. Cut o electrical power to the dishwasher.
2. Turn o the water supply and disconnect the water inlet pipe from the water valve.
3. Drain water from the inlet pipe and water valve. (Use a pan to catch the water)
4. Reconnect the water inlet pipe to the water valve.
5. Remove the filter in the tub the bottom and use a sponge to use up water in sump.
washing programmes _25
DD81-01446F-03_EN.indd 25DD81-01446F-03_EN.indd 25 2014-11-12 12:21:472014-11-12 12:21:47
Cleaning and care
HOW TO KEEP YOUR DISHWASHER IN SHAPE
• After Every Wash
After every wash, turn o the water supply to the appliance and leave the door slightly ajar so that
moisture and odours not trapped inside.
• Remove the Plug
Before cleaning or performing maintenance, always remove the plug from the socket.
• No Solvents or Abrasive cleaning
To clean the exterior and rubber parts of the dishwasher, do not use solvents or abrasive cleaning
products. use only a cloth and warm soapy water. To remove spots or stains from the surface of
the interior, use a cloth dampened with water and a little white vinegar, or a cleaning product made
specifically for dishwashers.
• When You Go on Holiday
When you go on holiday, it is recommened that you run a wash cycle with the dishwasher empty and
then remove the plug from the socket, turn o the water supply and leave the door of the appliance
slightly ajar. This will help the seals last longer and prevent odours from forming within the appliance.
• Moving the Appliance
If the appliance must be moved, try to keep it in the vertical position. If absolutely necessary, it can be
positioned on its back.
• Seals
One of the factors that cause odours to form in the dishwasher is food that remains trapped in the seals.
Periodic cleaning with a damp sponge will prevent this from occurring.
26_ washing programmes
DD81-01446F-03_EN.indd 26DD81-01446F-03_EN.indd 26 2014-11-12 12:21:472014-11-12 12:21:47
Troubleshooting
The manufacturer, following a policy of constant development and up-dating of
the product, may make modifications without giving prior notice.
BEFORE CALLING FOR SERVICE
PROBLEM POSSIBLE CAUSE WHAT TO DO
Dishwasher doesn’t
run
Drain pump doesn’t
stop
Noise • Some audible sounds are
Suds in the tub • Improper detergent. • Use only the special dishwasher
Stained tub interior • Detergent with colorant
Dishes are not dried • Rinse agent dispenser is
Dishes and flatware
not clean
• Fuse blown or the circuit
breaker acted.
• Power supply is not turned
on.
• Water pressure is low. • Check that the water supply is connected
• Overflow. • The system is designed to detect an
normal.
• Utensils are not secure in
the baskets or something
small has dropped into the
basket.
• Motor hums. • Dishwasher has not been used regularly.
• Spilled rinse agent. • Always wipe up rinse agent spills
was used.
empty.
• Improper program. • Select a more intensive wash program.
• Improper rack loading. • Make sure that the action of the detergent
• Replace fuse or reset circuit breaker.
Remove any other appliances sharing the
same circuit with the dishwasher.
• Make sure the dishwasher is turned on
and the door is closed securely.
Make sure the power cord is properly
plugged into the wall socket.
properly and the water is turned on.
overflow. When it does, it shuts o the
circulation pump and turns on the drain
pump.
• Sound from soft food shredding action
and detergent cup opening.
• To ensure everything is secured in the
dishwasher.
If you do not use it often, remember to
set it to fill and pump out every week,
which will help keep the seal moist.
detergent to avoid suds.
• If this occurs, open the dishwasher and
let suds evaporate.
• Add 1 gallon of cold water to the tub.
Close and latch the dishwasher, then
Start the “soak” wash cycle to drain out
the water. Repeat if necessary.
immediately.
• Make sure that the detergent is the one
without colorant.
• Make sure that the rinse agent dispense
is filled.
dispenser and spray arms are not
blocked by large dishware.
07 TROUBLESHOOTING
troubleshooting _27
DD81-01446F-03_EN.indd 27DD81-01446F-03_EN.indd 27 2014-11-12 12:21:472014-11-12 12:21:47
Troubleshooting
PROBLEM POSSIBLE CAUSE WHAT TO DO
Spots and filming on
glasses and flatware
Cloudiness on
glassware
Yellow or brown film on
inside surfaces
White film on inside
surface
Detergent cup lid won’t
latch
Detergent left in
dispenser cups
Steam • Normal phenomenon. • There is some steam coming through the
Black or gray marks on
dishes
Water standing in the
bottom of the tub
1. Extremely hard water.
2. Low inlet temperature.
3. Overloading the
dishwasher.
4. Improper loading.
5. Old or damp powder
detergent.
6. Empty rinse agent
dispenser.
7. Incorrect dosage of
detergent.
• Combination of soft water
and too much detergent.
• Tea or coee stains. • Using a solution of 1/2 cup of bleach and
• Iron deposits in water can
cause an overall film.
• Hard water minerals. • To clean the interior, use a damp sponge
• Dial is not in the OFF
position.
• Dishes block detergent
cups.
• Aluminum utensils have
rubbed against dishes.
• This is normal. • A small amount of clean water around the
To remove spots from glassware:
1. Take out all metal utensils out of the
dishwasher.
2. Do not add detergent.
3. Choose the longest cycle.
4. Start the dishwasher and allow it to run
for about 18 to 22 minutes, then it will be
in the main wash.
5. Open the door to pour 2 cups of white
vinegar into the bottom of the dishwasher.
6. Close the door and let the dishwasher
complete the cycle. If the vinegar does
not work: Repeat as above, except use
1/4 cup (60 ml) of citric acid crystals
instead of vinegar.
• Use less detergent if you have soft water
and select a shortest cycle to wash the
glassware and to get them clean.
3 cups warm water to remove the stains
by hand.
WARNING: You have to wait for 20
minutes after a cycle to let the heating
elements cool down before cleaning
interior; Failing to follow this instruct may
result in the risk of burns.
• You have to call a water softener
company for a special filter.
with dishwasher detergent and wear
rubber gloves. Never use any other
cleaner than dishwasher detergent for the
risk of foaming or suds.
• Turn the Dial to OFF position and slide the
door latch to the left.
• Re-loading the dishes properly.
vent by the door latch during drying and
water draining.
• Use a mild abrasive cleaner to eliminate
those marks.
outlet on the tub bottom keeps the water
seal lubricated.
28_ troubleshooting
DD81-01446F-03_EN.indd 28DD81-01446F-03_EN.indd 28 2014-11-12 12:21:472014-11-12 12:21:47
PROBLEM POSSIBLE CAUSE WHAT TO DO
Dishwasher leaks • Overfill dispenser or rinse
Buttons are not
working on power on
state
The result of washing performance may be caused by a power supply issue. Try another program
before contacting for service.
aid spills.
• Dishwasher isn’t level. • Make sure the dishwasher is level.
• Door is open. • When door is opened, buttons are not
• Child lock function is
selected.
• Be careful not to overfill the rinse aid
dispenser.
Spilled rinse aid could cause overusing
and lead to overflowing.
Wipe away any spills with a damp cloth.
working except Power button. Close the
door and press the button.
• When selected Child lock function,
buttons are not responded. To unlock
this function, hold down both the 3 in
1 and Delay start buttons for three (3)
seconds.
Also, Child lock function is released when
power cord is reconnected.
ERROR CODES
If an error occurs an error code may be displayed to inform you:
CODES MEANING POSSIBLE CAUSES
Water supply error
• Longer water inlet time
4E
Heater error
• Longer heating time, but not
HE
LE
tE
WARNING: If overflow occurs, turn o the main water supply before calling a service. If there is water
in the base pan because of an over fill or small leak, the water should be removed before restarting the
dishwasher.
reaching required temperature.
Leakage error
• Leakage sensor detect any
leakage water
Failure of temperature sensor Short/Open circuit or break of
1. Faucets is closed or water intake
is restricted.
2. Water pressure is too low.
3. Water inlet valve or Flow-meter is
not working.
4. Drain-pump is not working. (Water
pressure SW detect high level. so,
can not fill any more water.)
1. Heater or temperature sensor is
breakdown.
2. Water in Tub is too low on Heater
operation step.
3. Low level Protect device is not
working.
Overfilled into the dishwasher.
Leak from somewhere to bottom tray.
temperature sensor.
07 TROUBLESHOOTING
troubleshooting _29
DD81-01446F-03_EN.indd 29DD81-01446F-03_EN.indd 29 2014-11-12 12:21:482014-11-12 12:21:48
Appendix
SPECIFICATIONS
Model DW-FN320T, DW-FN320W
Type Freestanding Dishwasher Wash capacity 12 place setting
Power 220 - 240 V / 50 Hz AC only Water pressure 0.04 ~ 1.0 MPa
Rated power usage 1760-2100 W Hot water connection Max 60 °C
Dry type Condensed dry system Wash type Rotating nozzle spray
Dimensions 598 x 600 x 845 mm (Width×Depth×Height)
Weight Unpacked 53 kg
PRODUCT DIMENSION
600
598
845
1175
30_ appendix
DD81-01446F-03_EN.indd 30DD81-01446F-03_EN.indd 30 2014-11-12 12:21:482014-11-12 12:21:48
For standard test
The information for comparability test in accordance with EN 50242, as follows:
The diagrams below show the proper way to load the baskets based on the European
Standards(EN50242).
• Washing capacity: 12 place settings
• Test standard: EN50242/IEC60436
• Position of upper basket: to lower position
• Wash cycle : Eco
• Additional options: None
• Rinse aid setting: 3
• Water softener setting : H4
• Dosage of the standard detergent : pre/wash 5 g + main/wash 25 g
• For the arrangement of the items, refer below figures
<Upper basket>
1
3
IN
1
<Lower basket>
4
5
6
1
3
3
3
2
1
Cups
1
3
2
Saucers
Glasses
5
Medium serving bowl6Large serving bowl
4
Small serving bowl
7
IN
Dessert dishes
9
Soup plates
<Silverware basket>
1 Soup spoons 5 Dessert spoons
2 Forks 6 Serving spoons
3 Knives 7 Serving forks
4 Teaspoons 8 Gravy ladles
DD81-01446F-03_EN.indd 31DD81-01446F-03_EN.indd 31 2014-11-12 12:21:482014-11-12 12:21:48
8
Dinner plates
10
Oval platter
IN
for standard test _31
Product fiche
REGULATION (EU) NO 1059/2010
“ * ” Asterisk(s) means variant model and can be varied (0-9) or (A-Z).
Supplier SAMSUNG
Model name
Rated Capacity (place setting) 12
Energy eciency class A+
Annual energy consumption, (AE c) (kWh/year)
Standard cycle energy consumption, (E t) (kWh) 1.03
Power consumption in o mode, P o (W) 0.46
Power consumption in left-on mode, P l (W) 0.58
Annual water consumption, (AW c) (L/year)
Drying eciency class, A (most ecient) to G (least
ecient)
Standard programme
Programme time for the standard cycle, (min) 175
Duration of the left-on mode, (T l) (min) Unlimited
Airborne acoustical noise emissions (dBA re 1pW) 48
Installation
2)
3)
Built-in -
Built-under Yes
Free standing Yes
1) based on 280 standard cleaning cycles using cold water fill and the consumption of the low power
modes. Actual energy consumption will depend on how the appliance is used.
2) based on 280 standard cleaning cycles. Actual water consumption will depend on how the
appliance is used.
3) ‘Standard programme’ is the standard cleaning cycle to which the information in the label and the
fiche relates, that this programme is suitable to clean normally soiled tableware, and that it is the
most ecient programme in terms of combined energy and water consumption.
1)
2)
DW-FN320W
DW-FN320T
291
3360
A
Eco
32_ Product fiche
DD81-01446F-03_EN.indd 32DD81-01446F-03_EN.indd 32 2014-11-12 12:21:522014-11-12 12:21:52
Note
DD81-01446F-03_EN.indd 33DD81-01446F-03_EN.indd 33 2014-11-12 12:21:522014-11-12 12:21:52
Note
DD81-01446F-03_EN.indd 34DD81-01446F-03_EN.indd 34 2014-11-12 12:21:522014-11-12 12:21:52
Note
DD81-01446F-03_EN.indd 35DD81-01446F-03_EN.indd 35 2014-11-12 12:21:522014-11-12 12:21:52
QUESTIONS OR COMMENTS
COUNTRY CALL OR VISIT US ONLINE AT
INDIA
UK 0330 SAMSUNG (7267864) www.samsung.com/uk/support
DD81-01446F-03_EN.indd 36DD81-01446F-03_EN.indd 36 2014-11-12 12:21:522014-11-12 12:21:52
1800 3000 8282 - Toll Free
1800 266 8282 - Toll Free
www.samsung.com/in/support
Code No.: DD81-01446F-03_ENThis product is RoHS compliant
Loading...