7-5 MS9410 CODEC (Main PCB) (7-7)
7-6 DRAM (Main PCB) (7-8)
7-7 ATAPI (Main PCB) (7-9)
7-8 SAA7138 Video Decoder (Main PCB) (7-10)
7-9 DV Interface (Main PCB) (7-11)
7-10 Connector and Power (Main PCB) (7-12)
7-11 HDMI (Main PCB) (7-13)
7-12 Power Source (Jack PCB) (7-14)
7-13 B/E Connector (Jack PCB) (7-15)
7-14 FROM/To Front AV In PCB (Jack PCB) (7-17)
7-15 DVB TM Block (Jack PCB) (7-18)
7-16 I/O Switching (Jack PCB) (7-19)
7-17 I/O Jack (Jack PCB) (7-21)
7-18 New Front Micom (Jack PCB) (7-23)
7-19 Front AV Sub (Jack PCB) (7-24)
7-20 Function (Function PCB) (7-25)
5. Exploded View and Parts List 5-1 ~ 5-14
5-1 Cabinet Assembly (5-2)
5-2 Electrical Parts List (5-4)
6. PCB Diagrams 6-1 ~ 6-12
6-1 Wiring Diagram (6-2)
6-2 Main PCB (6-3)
6-3 Jack PCB (6-5)
6-4 S.M.P.S PCB (6-9)
6-4 Function PCB (6-11)
6-5 Front PCB (6-12)
7. Schematic Diagrams 7-1 ~ 7-26
7-1 All block Diagram (7-2)
7-2 Power (7-3)
7-3 S.M.P.S_01 (SMPS PCB) (7-5)
7-4 S.M.P.S_02 (SMPS PCB) (7-6)
2. Product Specication
2-1 Product Specication
Power requirements220-240 V AC, 50 Hz
Power consumption30 Watts / 2.5 Watts (Power off )
General
Input
Output
Recording
HDD Capac-
ity
USB
Weight3,8 Kg
Dimensions430 mm(W) x 300 mm(D) x 55 mm(H)
Operating temp.+5 °C to +35 °C
Other conditionsKeep level when operating. Less than 75% operating humidity
VideoComposite Video : 1.0 V p-p at 75Ω load, sync negative
AudioMax.Audio Input Level : 2 Vrms
DV InputIEEE 1394(4p) compatible jack
Receivable ChannelsPAL-B/G, SECAM-L/L', DVB-T
Scart Jack AV2 (Scart Ext) Video : Composite, RGB Audio: analogue
Audio
Video
Scart Jack AV1 (Scart TV)Video : Composite, RGB Audio: analogue
Picture Compression formatMPEG-II
Audio Compression formatDolby Digital 2ch/256Kbps, MPEG-II
Recording Quality
Audio Frequency Response20 Hz~20 kHz
DVD-SH873160 GB
DVD-SH875250 GB
DVD-SH877320 GB
USB 2.0 H/S
Analogue output jacks x 1
Optical/Coaxial digital audio output
Composite Video : Video output jack x 1
Component output x 1 (Y : 1,0Vp-p, Pb : 0,70Vp-p, Pr : 0,70Vp-p at 75Ω load)
HDMI/DVI (576P, 720P,1080i, 1080P)
XP (about 8,5 Mbps), SP (about 4,5 Mbps), LP (about 2,5 Mbps),
EP (about 1,6 Mbps or about 1,2 Mbps)
Host x 1
Audio Output
For DVD discs, audio signals recorded at 96 kHz sampling frequency are converted into and output at 48 kHz.
<Table 2-1>
Disc TypeDVDAUDIO CD (CD-DA)
Analogue Audio Output48 / 96 kHz44,1 kHz
Digital Audio Output48 kHz44,1 kHz
Samsung Electronics2-1
Product Specication
DVD-SH875 is SAMSUNG 4th DVD/HDD Recorder with Built In Set-Top Box(STB).
Built-in STB Module supply for Digital teresterial Television Reception in European Area.
And DVD-SH853 have HDMI ouput termianl which gives 576 line Progressive , 720 line Progressive ,1080 line
interlace and 1080P line Progressive Digital Video output
- Both Digital Television and also Radio Reception
- Enough Capacity of HARD Disk Drive(HDD)
Video Signal from STB Modeule is inputted as ITU-R BT.656 Digital Component Signal.
So, All the Process of STB video can be processed in Digital Domain for HDMI Video ouput.
-576P,720P,1080i,1080P Standard Denition HDMI Video ouput
-Board Lay-out of DVD-SH875 is rather complex than old model.
It consist of Main ,Jack ,Function ,Front-AV and S.M.P.S 5 PCBs Board Assembly and, DVD-Multi Loader and Hard
Disk Drive.
2-1-1 Maintenance of Cabinet
For safety reasons, be sure to disconnect the AC power cord from the AC outlet.
q Do not use benzene, thinner, or other solvents for cleaning.
q Wipe the cabinet with a soft cloth.
2-1-2 HDD (Hard Disk Drive)
q The hard disk has a high storage density, which enables long recording durations and quick access to written
data. However, it can easily be damaged by shock, vibration or dust and should be kept away from magnets.
To avoid losing important data, observe the following precautions.
q Do not use the HDD & DVD Recorder in a place subject to extreme changes in temperature.
q Do not apply a strong shock to the HDD & DVD Recorder.
q Do not place the HDD & DVD Recorder in a location subject to mechanical vibrations or in an unstable
location.
q Do not place the HDD & DVD Recorder on top of a heat source.
q Do not disconnect the AC power cord while the power is on.
q Do not attempt to change the hard disk. This may result in a malfunction.
Should the hard disk be damaged, you cannot recover lost data. The hard disk is only a temporary storage
space.
2-1-3 Disc Handling
q Use discs with regular shapes. If an irregular disc (a disc with a special shape) is
used, this HDD & DVD Recorder may be damaged.
2-1-4 Disc Speci cations
q This unit allows you to record and playback high quality digital video on DVD-RAM/W/ discs or on the
HDD.
You can also edit digital images on DVD-RAM/W discs or HDD.
Disc Type
2-2Samsung Electronics
<Table 2-2>
FORMATAPPLICATION
A digital versatile disc (DVD) can contain up to 135-minutes of images, 8 audio languages and 32 subtitle languages. It is
equipped with MPEG-2 picture compression and Dolby digital surrounding, allowing you to enjoy vivid and clear theatre
quality images in the comfort of your own home.
DVD-Video
Audio CD
CD-R/-RW
DVD
Disc Play-
back and
Recording
DVD-RW
Disc Play-
back and
Recording
DVD+RW
Disc Play-
back and
Recording
DVD-RAM
Disc Play-
back and
Recording
When switching from the rst layer to the second layer of a dual-layered DVD Video disc, there may be momentary distortion in the image and sound. This is not a malfunction of the unit.
Once a DVD-RW/ recorded in Video Mode is nalised, it becomes DVD-Video.
An audio disc on which 44.1 kHz PCM Audio is recorded.
Plays CD-DA format audio CD-R and CD-RW discs.
The unit may not be able to play some CD-R or CD-RW discs due to the condition of the recording.
Use a 700MB (80 minutes) CD-R/-RW disc. If possible, do not use a 800MB (90 minutes) or above disc, as the disc may not
play back.
If the CD-R/-RW disc was not recorded as a closed session, you may experience a delay in the early playback time, all
recorded les may not play.
Some CD-R/-RW discs may not be playable with this unit, depending on the device which was used to burn them. For contents recorded on CD-R/-RW media from CDs for your personal use, playability may vary depending on contents and discs.
Once a DVD recorded in Video Mode is nalised, it becomes DVD-Video.
You can record onto the available space on the disc and perform editing functions such as giving titles to discs and pro-
grammes and erasing programmes before nalising.
When programming is erased from a DVD, that space does not become available. Once an area on a DVD is recorded on, that area is no longer available for recording, whether the recording is erased or not.
It takes about 30 seconds for the unit to complete recording management information after recording nishes.
This product optimizes the DVD for each recording. Optimizing is carried out when you start recording after inserting the
disc or turning on the unit. Recording onto the disc may become impossible if optimizing is carried out too many times.
Playback may be impossible in some cases due to the condition of recording.
This unit can play back DVD discs recorded and nalised with a Samsung DVD video recorder. It may not be able to
play some DVD discs depending on the disc and the condition of the recording.
Recording and playback can be performed on DVD-RW discs in both the Video and VR Modes.
Once a DVD-RW recorded in both the Video and VR Modes is nalised, you cannot perform additional recording.
Once a DVD-RW recorded in Video Mode is nalised, it becomes DVD-Video.
In both modes, playback can be performed before and after nalisation, but additional recording, deleting and editing can
not be performed after nalisation.
If you want to record the disc in VR Mode and then record in V Mode, be sure to execute Format. Be careful when executing
Format because all the recorded data may be lost.
A DVD-RW blank disc is initialised to VR Mode when rst initialised.
With DVD+RW discs, there is no difference between DVD-Video format(Video mode) and DVD-Video Recording format(VR
mode).
Finalising is generally unnecessary when using a DVD+RW disc.
Ensure that the recording mode is set to VR mode. Otherwise, this product will not be able to play the recording.
You cannot play a DVD-RAM in most DVD components due to compatibility issues.
Only DVD-RAM standard Version 2.0. discs can be played in this unit.
DVD-RAM recorded on this unit may not work with other DVD components. To determine compatibility with these DVD-RAM
discs, refer to the user's manual for the player.
For cartridge type DVD-RAM discs, remove the cartridge and use the disc only.
Product Specication
Samsung Electronics2-3
Product Specication
2-1-5 Disc Copy
Title Copy Speci cations
<Table 2-3>
ContentsHDD DVDDVD HDD
Recorded Video TitleSupportedSupported
Copy Protected TitleNot supportedNot supported
Copy Once TitleMove (Deletes the Title in the HDD after copying)Not supported
Once "Copy Once programme" has been recorded on the DVD disc, this title cannot be copied to HDD
anymore.
But "Copy Once programme" has been recorded on the HDD, this title can be copied to DVD-RW (VR mode)
with CPRM or DVD-RAM.
Contents Copy Speci cations
<Table 2-4>
ContentsHDD DVD or USBDVD HDD or USBUSB HDD or DVD
MP3SupportedSupportedSupported
JPEG(photo)SupportedSupportedSupported
DivXSupportedSupportedSupported
q Disc(CD-R/CD-RW/DVD-RAM, DVD(Finalise)/ DVD+RW/DVD-RW(Finalise)) a HDD or USB
q HDD a DVD-R, DVD-RW(V) or USB
q USB a HDD or DVD-R, DVD-RW(V)
q The disc that has Video recording or has title dubbing from HDD can't be copied.
q PTP USB is not available when you copy to USB.
q If the disc is nalised through Disc Manager, it can be compatible with PC as a disc with a UDF le system.
COPY PROTECTION :
q Many DVD discs are encoded with copy protection.
q This product incorporates copyright protection technology that is protected by methods claims of
certain U.S. patents and other intellectual property rights owned by Macrovision
Corporation and other rights owners. Use of this copyright protection technology must be authorised by
Macrovision Corporation, is intended for home and other limited viewing uses only unless
otherwise authorised by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
7-8 SAA7138 Video Decoder (Main PCB) --------------------------------------------------------7-10
7-9 DV Interface (Main PCB) ----------------------------------------------------------------------------7-11
7-10 Connector and Power (Main PCB) ----------------------------------------------------------7-12
Note
● For schematic Diagram
- Resistors are in ohms, 1/8W unless otherwise noted.
Special note :
Most semiconductor devices are electrostatically sensitive and therefore require the special handling techniques
described under the “electrostatically sensitive (ES) devices” section of this service manual.
Note :
Do not use the part number shown on this drawing for ordering. The correct part number is shown in the parts list
(may be slightly different or amended since this drawing was prepared).
Important safety notices :
Components identied with the mark have the special characteristics for safety. When replacing any of these
components. Use only the same type.
1) Prevent residual high voltage at the terminals of
switch during switch off/Suppress noise.
High inverted power occurs at switch off,
because of the 1st winding of transformer :
(V=-L1 xdi/dt. L1 : Leakage Induction)
A very high residual voltage exist on both terminals
of ICIS01 because dt is a very short.
2) SNUBBER circuit protects ICIS01 from damage
through leakage voltage suppression by RC,
(Charges the leakage voltage to DIS05 and CIS08
and discharges to RIS03, RIS02).
3) CIS07 : For noise removal
Fig. 7-2
(c) IC1S01 Vcc circuit
1) ICIS01, RIS05, RIS07,RIS08 : ICIS01 driving resistance (ICIS01 works through driving resistance at power
cord in)
Fig. 7-1
2) ICIS01 Vcc : RIS05, RIS07, RIS08
q Use the output of transformer as Vcc,because the current starts to ow into transformer while ICIS01 is
active
w Rectify to DIS07 and smooth to CIS09.
e Use the output of transformer as ICIS01 Vcc : The loads are different before and after ICIS01 driving.
(Vcc of ICIS01 decreases below OFF voltage , using only the resistance dut to lode increase after ICIS01
driving.)
Samsung Electronics This Document can not be used without Samsung's authorization 7-3
Schematic Diagrams
(d) Feedback Control Circuit
Fig. 7-3
1) F/B terminal of PQIZ1 determines output duty cyle.
2) C-E (Collector-Emitter) of PQIZ1 and F/B potential of PQIZ1 are same.
7-2-3 Internal Block Diagram (Internal Block Diagram of S.M.P.S Circuit)
Fig. 7-4
7-4 This Document can not be used without Samsung's authorization Samsung Electronics
Power
Schematic Diagrams
7-3 S.M.P.S_01 (SMPS PCB)
qIC1S01 Pin(1)
u These are the waveforms of DVD-SH873, SH875, SH877, SH873M, SH875M, SH877M.
Caution There can be some differences (Voltage, Frequency, stc.) among cameras.
Samsung Electronics This Document can not be used without Samsung's authorization 7-5
Schematic Diagrams
7-4 S.M.P.S_02 (SMPS PCB)
u These are the waveforms of DVD-SH873,
SH875, SH877, SH873M, SH875M, SH877M.
qDRVCN1 12V Pin(1)wDRVCN1 5V Pin(4)
7-6 This Document can not be used without Samsung's authorization Samsung Electronics
Caution There can be some differences
(Voltage, Frequency, stc.) among cameras.
7-5 MS9410 CODEC (Main PCB)
Schematic Diagrams
Samsung Electronics This Document can not be used without Samsung's authorization 7-7
Schematic Diagrams
7-6 DRAM (Main PCB)
7-8 This Document can not be used without Samsung's authorization Samsung Electronics
7-7 ATAPI (Main PCB)
Schematic Diagrams
qDVDCN Pin(1)
Samsung Electronics This Document can not be used without Samsung's authorization 7-9
u These are the waveforms of DVD-SH873, SH875, SH877, SH873M, SH875M, SH877M.
Caution There can be some differences (Voltage, Frequency, stc.) among cameras.
Schematic Diagrams
7-8 SAA7138 Video Decoder (Main PCB)
qVR10 PCMO BCK
wVR8 PCMO LRCLK
eVR11 PCMO Data Out
rVR9 PCMIO XCLK
u These are the waveforms of DVD-SH873, SH875, SH877, SH873M, SH875M, SH877M.
Caution There can be some differences (Voltage, Frequency, stc.) among cameras.
7-10 This Document can not be used without Samsung's authorization Samsung Electronics
tVR28 VIN CLK
7-9 DV Interface (Main PCB)
Schematic Diagrams
Samsung Electronics This Document can not be used without Samsung's authorization 7-11
Schematic Diagrams
7-10 Connector and Power (Main PCB)
qDTIC1 27Mhz Pin(11)
wDXTAL 13.5MHz
u These are the waveforms of DVD-SH873, SH875, SH877, SH873M, SH875M, SH877M.
Caution There can be some differences (Voltage, Frequency, stc.) among cameras.
7-12 This Document can not be used without Samsung's authorization Samsung Electronics
7-11 HDMI (Main PCB)
Schematic Diagrams
Samsung Electronics This Document can not be used without Samsung's authorization 7-13
Schematic Diagrams
7-12 Power Source (Jack PCB)
7-14 This Document can not be used without Samsung's authorization Samsung Electronics
7-13 B/E Connector (Jack PCB)
Schematic Diagrams
Refer to a pattern
image of Table 7-5
u These are the waveforms of DVD-SH873, SH875, SH877, SH873M, SH875M, SH877M.
Caution There can be some differences (Voltage, Frequency, stc.) among cameras.
Samsung Electronics This Document can not be used without Samsung's authorization 7-15
Schematic Diagrams
qY-Color bar Pin(12)wC-Color bar Pin(14)
ePb-Color bar Pin(18)
yR in Pin(30)uG in Pin(28)iB in Pin(26)
rPr-Color bar Pin(20)tY-Color bar Pin(22)
oCVBS Input Jack (Color-Bar)
Pin(9)
aDigital Audio Data Pin(29), SJack3
sCN1 Pin(13,15)
Fig. 7-5
7-16 This Document can not be used without Samsung's authorization Samsung Electronics
Loading...
+ 100 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.