Samsung DVD-HR750 Operating Instructions

Instruction Manual

DVD-HR749 DVD-HR750

English

DVD-HR749

DVD-HR750

Ελληνικά

www.samsung.com/uk

AK68-01392A

Getting Started

Warning

Getting Started

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This symbol indicates “dangerous voltage” inside the product that presents a risk of electric shock or personal injury.

This symbol indicates important instructions accompanying the product.

Do not install this equipment in a conﬁ ned space such as a bookcase or similar unit.

WARNING : To prevent damage which may result in

ﬁ re or electric shock hazard, do not expose this appliance to rain or moisture.

CAUTION : HDD & DVD RECORDER USES AN

INVISIBLE LASER BEAM WHICH CAN CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE HDD & DVD RECORDER CORRECTLY AS INSTRUCTED.

CAUTION

THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

IMPORTANT NOTE

The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug. If it requires replacing, a fuse approved to BS1362 of the same rating must be used.

Never use the plug with the fuse cover omitted if the cover is detachable. If a replacement fuse cover is required, it must be of the same colour as the pin face of the plug. Replacement covers are available from your dealer.

If the ﬁ tted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should obtain a suitable safety approved extension lead or consult your dealer for assistance.

However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect the plug to a mains jack, as there is a risk of shock hazard from the bared ﬂ exible cord.

To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.

The product unit accompanying this user manual is licenced under certain intellectual property rights of certain third parties. This licence is limited to private non-commercial use by end-user consumers for licenced contents. No rights are granted for commercial use. The licence does not cover any product unit other than this product unit and the licence does not extend to any unlicenced product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit. The licence only covers the use of this product unit to encode and/or decode audio ﬁ les conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this licence for product features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.

This product satisﬁ es CE regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances, such as radios and televisions, use shielded cables and connectors for connections.

English - 2

Precaution

Important Safety Instructions

Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference.

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings, Install in

accordance with the manufacturer’s instructions.

Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus (including ampliﬁ ers) that produce heat.

Do not defeat the safety purpose of the polarized

or grounding- type plug. A polarized plug has two blades with one wider than the other. A groundingtype plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not ﬁ t into your outlet, consult an electrician for replacement of the obsolete outlet.

10)

Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles, the point where they exit from the apparatus.

11)

Only use attachments/accessories speciﬁ ed by the

manufacturer.

12)

Use only with the cart, stand, tripod, bracket, or

table speciﬁ ed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13)

Unplug this apparatus during lightning storms or

when unused for long periods of time.

14)

Refer all servicing to qualiﬁ ed service personnel.

Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Handling Cautions

Before connecting other components to this HDD &

• DVD RECORDER, be sure to turn them all off.

Do not move the HDD & DVD RECORDER while a

• disc is being played, or the disc may be scratched or broken, the HDD & DVD RECORDER internal parts may be damaged.

Do not put a ﬂ ower vase ﬁ lled with water or any small

• metal objects on the HDD & DVD RECORDER.

Be careful not to put your hand into the disc tray.

• Do not place anything other than the disc in the disc

• tray.

Exterior interference such as lightning and static

• electricity can affect normal operation of this HDD & DVD RECORDER. If this occurs, turn the HDD & DVD RECORDER off and on again with the STANDBY/ON button, or disconnect and then reconnect the AC power cord to the AC power outlet. The HDD & DVD RECORDER will operate normally.

Be sure to remove the disc and turn off the HDD &

• DVD RECORDER after use.

Disconnect the AC power cord from the AC outlet

• when you don’t intend to use the HDD & DVD RECORDER for long periods of time.

Clean the disc by wiping in a straight line from the

• inside to the outside of the disc.

Apparatus shall not be exposed to dripping or

• splashing and no objects ﬁ lled with liquids, such as vases, shall be placed on the apparatus.

The Mains plug is used as a disconnect device and

• shall stay readily operable at any time.

Maintenance of Cabinet

For safety reasons, be sure to disconnect the AC power cord from the AC outlet.

•

Do not use benzene, thinner, or other solvents for cleaning.

•

Wipe the cabinet with a soft cloth.

HDD (Hard Disk Drive)

The hard disk has a high storage density, which enables long recording durations and quick access to written data. However, it can easily be damaged by shock, vibration or dust and should be kept away from magnets. To avoid losing important data, observe the following precautions.

Do not use the HDD & DVD RECORDER in a place

• subject to extreme changes in temperature.

Do not apply a strong shock to the HDD & DVD

• RECORDER.

Getting Started

English - 3

•

Do not place the HDD & DVD RECORDER in a location subject to mechanical vibrations or in an unstable location.

•

Do not place the HDD & DVD RECORDER on top of a heat source.

•

Do not disconnect the AC power cord while the power is on.

Getting Started

•

Do not attempt to change the hard disk. This may result in a malfunction.

Should the hard disk be damaged, you cannot recover lost data. The hard disk is only a temporary storage space.

Disc Handling

Use discs with regular

• shapes. If an irregular disc (a disc with a special shape) is used, this HDD & DVD RECORDER may be damaged.

Holding discs

Avoid touching the surface of a

• disc where recording is performed.

Disc Storage

Be careful not to harm the disc because the data on these discs is highly vulnerable to the environment.

•

Do not keep under direct sunlight.

•

Keep in a cool ventilated area.

•

Store vertically.

•

Keep in a clean protection jacket.

If you move your HDD & DVD RECORDER suddenly

• from a cold place to a warm place, condensation may generate on the operating parts and lens and cause abnormal disc playback. If this occurs, do not connect the plug to the power outlet and wait for two hours. Then insert the disc and try to play back again.

Disc Speciﬁ cations

•

DVD-HR749 / DVD-HR750

This unit allows you to record and playback high quality digital video on DVD-RAM/-RW/-R discs or on the HDD. You can also edit digital images on DVD-RAM/-RW discs or HDD.

Disc Type

DVD-RAM, DVD-RW and DVD-R

Clean with an optional DVD-RAM/

• PD disc cleaner (LF-K200DCA1 where available). Do not use cleaners or cloths for CDs to clean DVD-RAM/-RW/-R discs.

DVD-Video, Audio-CD

Wipe off dirt or contamination on the disc with a soft

• cloth.

Cautions on handling discs

Do not write on the printed side with a ball-point pen

• or pencil.

Do not use record cleaning sprays or antistatic. Also,

• do not use volatile chemicals, such as benzene or thinner.

Do not apply labels or stickers to discs. (Do not use

• discs ﬁ xed with exposed tape adhesive or leftover peeled-off stickers.)

Do not use scratch-proof protectors or covers.

•

Do not use discs printed with label printers available

• on the market.

•

Do not load warped or cracked discs.

DVD-Video

◆

A digital versatile disc (DVD) can contain up to

• 135-minutes of images, 8 audio languages and 32 subtitle languages. It is equipped with MPEG-2 picture compression and Dolby digital surrounding, allowing you to enjoy vivid and clear theatre quality images in the comfort of your own home.

•

When switching from the ﬁ rst layer to the second layer of a dual-layered DVD Video disc, there may be momentary distortion in the image and sound. This is not a malfunction of the unit.

Once a DVD-RW/-R recorded in Video Mode is

• ﬁ nalised, it becomes DVD-Video.

Audio CD

◆

An audio disc on which 44.1 kHz PCM Audio is

• recorded.

Plays CD-DA format audio CD-R and CD-RW discs.

•

The unit may not be able to play some CD-R or

• CD-RW discs due to the condition of the recording.

English - 4

CD-R/-RW

◆

Use a 700MB (80 minutes) CD-R/-RW disc. If

• possible, do not use a 800MB (90 minutes) or above disc, as the disc may not play back.

If the CD-R/-RW disc was not recorded as a closed

• session, you may experience a delay in the early playback time, all recorded ﬁ les may not play.

Some CD-R/-RW discs may not be playable with this

• unit, depending on the device which was used to burn them. For contents recorded on CD-R/-RW media from CDs for your personal use, playability may vary depending on contents and discs.

DVD-R Disc Playback and Recording

◆

Once a DVD-R recorded in Video Mode is ﬁ nalised,

• it becomes DVD-Video.

You can record onto the available space on the disc

• and perform editing functions such as giving titles to discs and programmes and erasing programmes before ﬁ nalising.

When programming is erased from a DVD-R, that

• space does not become available. Once an area on a DVD-R is recorded on, that area is no longer available for recording, whether the recording is erased or not.

It takes about 30 seconds for the unit to complete

• recording management information after recording ﬁ nishes.

This product optimizes the DVD-R for each

• recording. Optimizing is carried out when you start recording after inserting the disc or turning on the unit. Recording onto the disc may become impossible if optimizing is carried out too many times.

Playback may be impossible in some cases due to

• the condition of recording.

This unit can play back DVD-R discs recorded and

• ﬁ nalised with a Samsung DVD video recorder. It may not be able to play some DVD-R discs depending on the disc and the condition of the recording.

DVD-RW Disc Playback and Recording

◆

Recording and playback can be performed on

• DVD-RW discs in both the Video and VR Modes.

Once a DVD-RW recorded in both the Video and VR

• Modes is ﬁ nalised, you cannot perform additional recording.

Once a DVD-RW recorded in Video Mode is

• ﬁ nalised, it becomes DVD-Video.

In both modes, playback can be performed before

• and after ﬁ nalisation, but additional recording, deleting and editing can not be performed after ﬁ nalisation.

If you want to record the disc in VR Mode and then

• record in V Mode, be sure to execute Format. Be careful when executing Format because all the recorded data may be lost.

•

A DVD-RW blank disc is initialized to VR Mode when ﬁ rst initialized.

DVD-RAM Disc Playback and Recording

◆

Ensure that the recording mode is set to VR mode.

• Otherwise, this product will not be able to play the recording.

You cannot play a DVD-RAM in most DVD

• components due to compatibility issues.

Only DVD-RAM standard Version 2.0. discs can be

• played in this unit.

DVD-RAM recorded on this unit may not work with

• other DVD components. To determine compatibility with these DVD-RAM discs, refer to the user’s manual for the player.

For cartridge type DVD-RAM discs, remove the

• cartridge and use the disc only.

Getting Started

English - 5

Disc Copy

Contents Copy Speciﬁ cations

Contents HDD

Recorded Video Title

Getting Started

Copy Protected Title

Copy Once Title

MP3 Supported Supported

JPEG(photo) Supported Supported

DivX Supported Supported

Once “Copy Once programme” has been recorded on the DVD disc, this title cannot be copied to HDD anymore.

But “Copy Once programme” has been recorded on the HDD, this title can be copied to DVD-RW (VR mode) or DVD-RAM.

When you copy MP3/JPEG/DivX ﬁ les from HDD to DVD, only DVD-RW(V)/-R discs are available.

(Deletes the Title in the

➔

DVD DVD ➔ HDD

Supported Supported

Not supported Not supported

Move

Not supported

HDD after copying)

For more information on DVD recording compatibility,

❋

consult your DVD-RAM/-RW/-R manufacturer.

❋

Use of poor quality DVD-RAM/-RW/-R discs may cause following unexpected problems including, without limitation, recording failure, loss of recorded or edited materials or damage to the HDD & DVD RECORDER.

Disc Format

Using MP3 disc

◆

CD-R/-RW, DVD-RAM/±RW/±R, HDD with MP3 ﬁ les

• recorded with UDF, ISO9660 or JOLIET format can be playbacked.

Only MP3 ﬁ les with the “.mp3” or “.MP3” extension

• can be played.

For MP3 ﬁ les recorded with a VBR(Variable Bit

• Rates), from 32 Kbps to 320 Kbps, the sound may cut in out.

Playable bit-rate range is from 56 Kbps to 320 Kbps.

•

Each folder can have up to 500 items including ﬁ les

• and sub folders.

COPY PROTECTION

•

Many DVD discs are encoded with copy protection. Because of this, you should only connect your HDD & DVD RECORDER directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy-protected DVD discs.

•

This product incorporates copyright protection technology that is protected by methods claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorised by Macrovision Corporation, is intended for home and other limited viewing uses only unless otherwise authorised by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Protection

This HDD & DVD RECORDER can allow you to protect the contents of your discs, as described below.

Programme-protected: See page 74 “Locking

• (Protecting) a Title”

Disc-protected: See page 91 “Disc Protection”

•

❋

DVD-RAM/±RW/±R discs that are incompatible with the DVD-VIDEO format cannot be played with this product.

Using JPEG disc

◆

CD-R/-RW, DVD-RAM/±RW/±R, HDD recorded with

• UDF, ISO9660 or JOLIET format can be playbacked.

Only JPEG ﬁ les with the “.jpg” or “.JPG” extension

• can be displayed.

Each folder can have up to 500 items including ﬁ les

• and sub folders.

MOTION JPEG and progressive JPEG are not

• supported.

Using DivX disc

◆

Disc : CD-R/-RW, DVD-RAM/±RW/±R, HDD

•

Video File with following extensions can be played. :

• .avi, .divx, .AVI, .DIVX

DivX Video (Codec) Format : DivX 3.11 DivX 4.x

• DivX 5.x (without QPEL and GMC)

DivX Audio (Codec) Format : MP3, MPEG1 Audio

• Layer 2, LPCM, AC3

Supported subtitle ﬁ le formats: .smi, .srt, .sub, .psb,

• .txt, .ass

Each folder can have up to 500 items including ﬁ les

• and sub folders.

You cannot play back the disc that is larger than a

• 720 x 576 pixel resolution.

English - 6

Do not use the following discs!

LD, CD-G, CD-I, CD-ROM and DVD-ROM discs

• should not be used in this product.

[Note]

Disc types that can be played : CD/CD-R/-RW/MP3/ JPEG/DVD-Video/DVD-RAM/-RW/-R. For a DVD-RW/-R disc, which has been recorded in Video Mode on another component, it can play only when ﬁ nalised.

Some commercial discs and DVD discs purchased

• outside your region may not be playable with this product. When these discs are played, either “No disc.” or “Please check the regional code of the disc.” will be displayed.

If your DVD-RAM/±RW/±R discs is an illegal copy or

• is not in DVD video format, it may also not be playable.

Disc compatibility

◆

High Speed Recording discs can be used in this unit.

•

Not all brands of discs will be compatible with this

• unit.

Getting Started

English - 7

Getting Started

Warning ....................................................................... 2



Precaution ................................................................... 3



Important Safety Instructions ...................................... 3

Handling Cautions ....................................................... 3

Maintenance of Cabinet .............................................. 3

HDD (Hard Disk Drive) ............................................... 3

Disc Handling .............................................................. 4

Disc Storage................................................................ 4

Disc Specifications ...................................................... 4

Disc Copy .................................................................... 6



General Features ...................................................... 10



Before reading the user’s manual ............................ 11



How to use the HDD & DVD RECORDER .............. 11



Unpacking ................................................................. 13



Description ................................................................ 15

Front Panel ................................................................ 15

Rear Panel ................................................................ 16

Front Panel Display .................................................. 16

Tour of the Remote Control ...................................... 17

Contents

Connecting to AV 3 IN, DV input jack ..................... 22



Case 1 : Connecting a VCR, Set-Top Box(STB), DVD player or Camcorder

to the AV 3 IN jacks ................................................. 22

Case 2 : Connecting a Camcorder

to the DV IN jack ...................................................... 23

System Setup



On-Screen Menu Navigation .................................... 24



Plug & Auto Setup .................................................... 24



Setting the Clock ....................................................... 25



Channel Set ............................................................. 26

Auto Setup ................................................................ 26

Manual Setup ............................................................ 26



Setting up the Language Options ............................. 27



Setting up the System Options ................................. 27

Auto Power Off Setting ............................................. 28

Automatic Chapter Creator ....................................... 28

EP Mode Time Setting .............................................. 29

EZ Record ................................................................. 29

DivX(R) Registration ................................................. 29

Connecting & Setting Up

Connecting the HDD & DVD RECORDER .............. 18



Additional connections .............................................. 18

Other type of connecting the Video output cable .... 19



Case 1 : Connecting to a Video (Composite)

output jack ................................................................. 19

Case 2 : Connecting to an S-Video output jack ...... 20

Case 3 : Component Video output jacks.................. 20



Other type of connecting the Audio output cable .... 21

Case 1 : Connecting to your TV .............................. 21

Case 2 : Connecting to a stereo amplifier with

AV output jacks ........................................................ 21

Case 3: Connecting to an AV amplifier with a

digital output jack ..................................................... 22

English - 8



Setting up the Audio Options .................................... 30



Setting up the Video Options .................................... 32



Setting up the Parental Lock .................................... 35

If you forgot your password ...................................... 35

Setting the Rating Level ........................................... 35

Changing the Password ........................................... 35

Playback

Region code (DVD-Video only) ................................ 36



Logos of Discs that can be played ........................... 36



Disc types that can be played .................................. 36



Playing a Disc ........................................................... 37



Using the Disc Menu & Title Menu ........................... 38



Using the playback related buttons .......................... 39



Using the INFO button .............................................. 41



Selecting the Subtitle Language ............................... 41



Selecting the Soundtracks & Audio Channels ......... 42



Changing the Camera Angle .................................... 42



Repeat Play............................................................... 43



Zooming-In ................................................................ 44



Using Markers ........................................................... 45



Using the Bookmarks ................................................ 46



Playing an Audio CD/MP3 ........................................ 47



Viewing a Picture ...................................................... 52



Playing a DivX ........................................................... 54



Recording

Recordable Discs ...................................................... 56



Recording Formats ................................................... 57



Recording Mode ........................................................ 58



Unrecordable pictures ............................................... 59



Recording immediately ............................................. 60



Copying from a Camcorder ...................................... 62



Making a One Touch Recording (OTR) ................... 63



Simultaneous Recording and Playback ................... 64



Time Shift function as a live signal ........................... 65



Making a Timer Recording ...................................... 66



Editing the Scheduled List ........................................ 68

Adding a Scheduled List ........................................... 68

Deleting a Scheduled List ......................................... 69



Using the Video Plus+ Feature ................................ 70



Video Plus+ Extended .............................................. 71

Editing

Basic Editing (Title List) ............................................ 73



Playing the Title ........................................................ 73

Renaming (Labeling) a Title ..................................... 73

Locking (Protecting) a Title ...................................... 74

Deleting a Title ........................................................ 75

Splitting a Section of a Title (Split) ......................... 76

Deleting a Section of a Title (Partial Delete) .......... 77



Using the Sort function (Title List) ............................ 78

Navigation Menu ....................................................... 78



Select Contents ......................................................... 79



Advanced Editing (Playlist) ....................................... 80



Creating a Playlist .................................................... 80

Playing Entries in the Playlist .................................. 81

Renaming a Playlist Entry ........................................ 81

Editing a Scene for the Playlist ................................. 82

Deleting a Playlist Entry from the Playlist................. 84

Using the Sort (Playlist) ............................................ 85



Copying from HDD to DVD ....................................... 85



Copying from DVD to HDD ....................................... 87



Copying MP3, JPEG or DivX .................................... 88

File Copy ................................................................... 88

Folder Copy............................................................... 88



Changing the name of Music/Photo/DivX file ........... 90



Disc Manager ............................................................ 91

Editing the Disc Name .............................................. 91

Disc Protection .......................................................... 91

Delete All Title Lists ................................................. 92

Delete All Title Lists/DivX Lists /Music Lists/

Photo Lists ................................................................ 92

Formatting a Disc ...................................................... 93

Finalising a Disc ....................................................... 94

Unfinalising a Disc (V/VR mode) ............................. 95

Getting Started



Go To Recorded List................................................. 71

English - 9

Reference

Troubleshooting ........................................................ 96



Specifications ............................................................ 98



General Features

•

DVD-HR749 / DVD-HR750

This unit allows you to record and playback high quality digital video on DVD-RAM/-RW/-R discs or on the HDD. You can also edit digital images on DVD-RAM/-RW

Getting Started

discs or HDD.

HDD Recording

•

DVD-HR749 / DVD-HR750

You can record up to Approx. 199 hours of video (in EP mode) on the internal 160GB (gigabyte) hard disk (HDD).

With both recordable DVD and a high-capacity HDD in the same recorder, you have the ﬂ exibility to keep recordings on the HDD for quick access anytime, or record to DVD for archiving or playing on other DVD players.

Copy between HDD and DVD

You can copy recordings from the HDD to recordable DVD, or from DVD to the HDD.

You can only copy in the same record mode as source title.

Simultaneous Recording and Playback

Playback and recording for both the DVD and the built-in hard disk drive (HDD) are completely independent. For example you can record a broadcast programme to either a recordable DVD or the HDD, while watching another recording you already made on the same DVD or on the HDD.

High quality digital audio and video recording and playback

You can record up to approximately 16-hours of video on a double side 9.4GB DVD-RAM disc, up to 15-hours on a dual-layer 8.5GB DVD-R disc, and up to 8-hours on a 4.7GB DVD-RAM/-RW/-R disc, depending on the recording mode.

Automated Quality Adjustment for Timer Recording

If FR mode is selected, the video quality is adjusted automatically so that all video for the scheduled time can be recorded onto the free disc space. (See page 66)

Creating a DVD video title using DVD-RW/-R disc

With the HDD & DVD RECORDER, you can create your own DVD Video titles on 4.7 GB DVD-RW/-R discs.

Copying data from a digital camcorder using a DV input jack

Record DV Device video onto HDD and DVD-RAM/

-RW/-R discs using the DV input jack (IEEE 1394-4pin/4pin). (See page 62)

High quality progressive scan

Progressive scanning provides high resolution and ﬂ icker free video. The 10-bit 54-MHz DAC and 2D Y/C Separating Circuitry provides the highest image playback and recording quality. (See pages 33~34)

DivX Certiﬁ cation

DivX, DivX Certiﬁ ed, and associated logos are trademarks of DivX Networks, Inc and are used under licence.

EZ Record Mode

This function allows you Initialise and Finalise a disc automatically. (See page 29)

Selectable Recording Mode

You can set your HDD & DVD RECORDER to one of four different recording speeds, each varying in recording quality and length. EP (6Hr or 8Hr) mode yields the most recording time, LP & SP modes provide less recording time with higher quality recording, XP mode gives you the highest quality recording.

The dual layer DVD-Rs have approximately double the capacity of single layer DVD-Rs. (See page 36)

English - 10

Before reading the user’s manual

Make sure to check the following terms before reading the user manual.

Icons that will be used in manual

Getting Started

Icon Term Deﬁ nition

S Z X

C V B

G A D J M

About the use of this user’s manual

Be sure to be familiar with Safety Instructions

before using this product. (See pages 2~7)

If a problem occurs, check the Troubleshooting.

(See pages 96~97)

HDD

DVD

RAM

-RW

-R

JPEG

MP3

DivX

Caution

NOTE

One-Touch

button

This involves a function available on the HDD.

This involves a function available on DVD or DVD±R/-RW(V) discs that have been ﬁ nalised.

This involves a function available on DVD-RAM.

This involves a function available on DVD-RW.

This involves a function available on DVD-R.

This involves a function available on a data CD (CD-R or CD-RW).

This involves a function available on CD-R/-RW, DVD±R/±RW/

-RAM discs or HDD. This involves a function available

on CD-R/-RW, DVD±R/±RW/

-RAM discs or HDD. This involves a function available

on CD-R/-RW, DVD±R/±RW/

-RAM discs or HDD. This involves a case where a

function does not operate or settings may be cancelled.

This involves tips or instructions on the page that help each function operate.

A function that can be operated by using only one button.

How to use the HDD & DVD RECORDER

Step 1: Select the disc type or HDD

Please check available disc type before recording.

DVD-HR749 / DVD-HR750

•

If you want to repeatedly record on the same disc or you want to edit the disc after recording, select a rewritable DVD-RW or DVD-RAM type disc. If you want to save a recording without any changes, choose a non-rewritable DVD-R. You can record ﬁ les directly to the built-in HDD or edit a recorded ﬁ le.

Step 2:

Unlike a VCR, the HDD & DVD RECORDER automatically starts formatting when an unused disc is inserted. This is required for the preparation of recording on a disc.

Using the HDD

Formatting unnecessary.

Using a DVD-RAM

This type of disc can be formatted in DVD-Video Recording format (VR mode). You can edit recorded images and create a playlist in a speciﬁ c sequence according to your requirements.

Using a DVD-RW

This type of disc can be formatted in either DVD-Video format (V mode) or DVD-Video Recording format (VR mode). For an unused disc, a message that asks whether to initialize a disc or not. If you select “DVD-VR” or “DVD-V”, initialising will be started. You can play a Video mode disc on various DVD components. A VR mode disc allows more varied editing.

Format the disc to start recording

English - 11

Using a DVD-R

Formatting disc is unnecessary and only V Mode Recording is supported. You can play these type of discs on various DVD components only when they have been ﬁ nalised.

Getting Started

You can only use either the VR or Video mode



on a DVD-RW, but not both at the same time.

You can format a DVD-RW to V or VR mode



using Disc Manager. It should be noted that the disc’s data will be lost when changing formats.

Step 3: Recording

There are two different recording methods, Direct Recording and Timer Recording. Timer recording is classiﬁ ed as follows:

Recording mode : XP (high quality mode), SP (standard quality mode), LP (long recording mode), and EP (extended mode) according to the recording mode. When recording is set in the FR mode, the best quality picture is recorded with regards to the remaining time on the disc.

Step 4: Playing

You can select the title you want to play in a displayed menu and then immediately start playback.

A DVD consists of sections, called titles, and subsections, called chapters.

During recording, a title is created between two points where you start and stop recording. Chapters will be created automatically when you ﬁ nalise recording on DVD-RW/-R discs in Video mode. The chapter’s length (interval between chapters) varies according to the recording mode.

Step 5: Editing a recorded disc

Editing on discs is easier than conventional video tapes. The HDD & DVD RECORDER supports many different edit functions, possible only with DVDs and HDD.

With a simple and easy edit menu, you can operate various edit functions, such as delete, copy, rename, lock, etc., on a recorded title.

Creating a playlist (DVD-RAM/-RW in VR mode, HDD)

With this HDD & DVD RECORDER, you can create a new playlist on a disc and edit it without the original, pre-existing recording.

Step 6: Finalising & Playing on other DVD components

To play your DVD on other DVD components, ﬁ nalising may be necessary. First, ﬁ nish all editing and recording operations, then ﬁ nalise the disc.

When using a DVD-RW disc in VR Mode

DVD discs recorded in VR mode can only be played back in DVD recorders, not players.

When using a DVD-RW disc in Video Mode

The disc should be ﬁ nalised ﬁ rst to enable playback on anything other than this HDD & DVD RECORDER. No more editing or recording can be made on the disc once it has been ﬁ nalised. To enable recording on the disc again, the disc must be unﬁ nalised.

When using a DVD-R disc

You should ﬁ nalise the disc to play it on a component other than this HDD & DVD RECORDER. You cannot edit or record on the disc once it has been ﬁ nalised.

You can ﬁ nalise the disc automatically using



EZ Record function. (See page 29)

English - 12

Unpacking

Accessories

Check for the supplied accessories below.

Video/Audio Cable

Remote Control

RF Cable for TV

Batteries for Remote

Control (AAA Size)

Preparing the Remote Control

Install Batteries in the Remote Control

•

Open the battery cover on the back of the remote control.

•

Insert two AAA batteries. Make sure that the polarities (+ and –) are aligned correctly.

•

Replace the battery cover.

If the remote does not operate properly:

•

Check the polarity + – of the batteries (Dry-Cell)

•

Check if the batteries are drained.

•

Check if remote sensor is blocked by obstacles.

•

Check if there is any ﬂ uorescent lighting nearby.

Dispose of batteries according to local environmental regulations. Do not put them in the household trash.

Getting Started

Instruction Manual Quick Guide

To determine whether your television is compatible, follow the instructions below.

Switch your television on.

Point the remote control towards the television.

Press and hold the TV STANDBY/ON button and enter the two-ﬁ gure code corresponding to the brand of your television, by pressing the appropriate number buttons.

English - 13

Controllable TV Codes

BRAND BUTTON

SAMSUNG 01, 02, 03, 04, 05, 06, 07, 08, 09

AIWA 82

ANAM 10, 11, 12, 13, 14, 15, 16, 17, 18

Getting Started

BANG & OLUFSEN

BLAUPUNKT 71

BRANDT 73

BRIONVEGA 57

CGE 52

CONTINENTAL EDISON

DAEWOO

EMERSON 64

FERGUSON 73

FINLUX 06, 49, 57

FORMENTI 57

FUJITSU 84

GRADIENTE 70

GRUNDIG 49, 52, 71

HITACHI 60, 72, 73, 75

IMPERIAL 52

JVC 61, 79

LG 06, 19, 20, 21, 22, 78

LOEWE 06, 69

LOEWE OPTA 06, 57

MAGNAVOX 40

METZ 57

MITSUBISHI 06, 48, 62, 65

MIVAR 52, 77

NEC 83

NEWSAN 68

NOBLEX 66

NOKIA 74

NORDMENDE 72, 73, 75

PANASONIC 53, 54, 74, 75

PHILIPS 06, 55, 56, 57

PHONOLA 06, 56, 57

PIONEER 58, 59, 73, 74

RADIOLA 06, 56

RADIOMARELLI 57

RCA 45, 46

REX 74

SABA 57, 72, 73, 74, 75

SALORA 74

19, 20, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34

BRAND BUTTON

SANYO 41, 42, 43, 44, 48

SCHNEIDER 6

SELECO 74

SHARP 36, 37, 38, 39, 48

SIEMENS 71

SINGER 57

SINUDYNE 57

SONY 35, 48

TELEAVA 73

TELEFUNKEN 67, 73, 75, 76

THOMSON 72, 73, 75

THOMSON ASIA 80, 81

TOSHIBA 47, 48, 49, 50, 51, 52

WEGA 57

YOKO 6

ZENITH 63

Result: If your television is compatible with the remote

control, it will switch off. It is now programmed to operate with the remote control.

If several codes are indicated for your



television brand, try each one in turn until you ﬁ nd one that works.

If you replace the remote control’s batteries,



you must set the brand code again.

Then you can control the television using the following buttons after pressing the TV button.

Button Function

TV STANDBY/ON

INPUT SEL. Used to select an external source.

TV VOL (+ –)

PROG (,.)

TV MUTE Used to toggle the sound on and off.

Number Used to input number directly.

The functions listed above will not necessarily



work on all televisions. If you encounter problems, operate the television directly.

Used to switch the television on and off.

Used to adjust the volume of the television.

Used to select the desired channel.

English - 14

Description

Front Panel

Getting Started

DVD-HR749

DVD-HR750

STANDBY/ON button

Turns the HDD & DVD RECORDER on and off.

DISC TRAY

Opens to accept a disc.

OPEN/CLOSE button

Opens and closes the disc tray.

DISPLAY

Displays the playing status, time, etc.

AV 3 INPUT

Connect external equipment.

DV-INPUT

Connect external digital equipment with a DV jack. (such as a camcorder)

P.SCAN button

Selects the progressive scan mode.

DVD button

Select DVD mode.

10.

11.

12.

13.

14.

English - 15

HDD button

Select HDD mode.

PROG buttons

Select TV preset Channels. Same as PROG button on the remote control.

REC button

Starts recording.

STOP button

Stops disc playback.

PLAY/PAUSE button

Plays a disc or pauses playback.

SEARCH/SKIP buttons

Goes to the next title/chapter/track or goes back to the previous title/chapter/track.

Rear Panel

Getting Started

DIGITAL AUDIO OUT(OPTICAL)

Connects to an ampliﬁ er having a digital optical audio input jack.

DIGITAL AUDIO OUT(COAXIAL)

Connects to an ampliﬁ er having a digital coaxial audio input jack.

AUDIO OUT

Connects to the audio input of external equipment using audio cables.

VIDEO OUT

Connects the input of external equipment using a Video cable.

Fan

The fan always revolves when the power is on. Ensure a minimum of 10 cm clear space on all sides of the fan when installing the product.

S-VIDEO OUT

5. Connects the input of external equipment using an S-Video cable.

COMPONENT VIDEO OUT

6. Connects to equipment having Component video input.

AV1(TV) OUTPUT SCART connector

AV2(EXT) INPUT SCART connector

In from aerial connector

Out to TV connector

10.

The Antenna connection does not pass the



output signal of the DVD. To watch DVD/HDD playback your TV, you must connect audio/ video or Scart cables.

Front Panel Display

Lights when a disc is loaded.

Lights in the record mode.

Lights when a HDD/DVD is selected.

Lights when a DVD-RAM/-RW/-R disc is loaded.

English - 16

Playing time/clock/current status indicator.

Lights in the progressive scan mode.

Lights to indicate the timer record mode.

Tour of the Remote Control

Your HDD & DVD RECORDER remote control will work with Samsung televisions and compatible brands.

13.

INFO button

This will display current setting or disc status.

14.

TITLE LIST/DISC MENU button

Use this to enter the View Recording list/disc menu.

15.

COLOUR button : RED(A), GREEN(B), YELLOW(C), BLUE(D)

Allows access to common function of HDD & DVD RECORDER.

COPY button

16. Press this when you copy DVD to HDD and vice-versa. To start copying, press the COPY button on the title list screen or press the COPY button during the playback.

REC button

17. Use to make a recording on HDD/DVD-RAM/-RW/-R discs.

MARKER button

18. Use this to bookmark a position while playing a disc.

19.

HDD button

Press this to operate HDD.

20.

INPUT SEL button

Select input signal in external input mode (PROG, AV1, AV2, AV3 or DV input)

21.

OPEN/CLOSE button

To open and close the disc tray.

22.

TV STANDBY/ON button

23.

REPEAT A-B button

Allows you to repeat a title, chapter, track or disc.

24.

REPEAT button

Allows you to repeat a title, chapter, track or disc.

25.

PLAY/PAUSE button

Press to play/pause a disc.

26.

DVD button

1. Press this to operate DVD.

TV button

2. Press this to operate TV.

STANDBY/ON button

NUMBER buttons

TV/DVD button

SUBTITLE button

6. Press this to switch the DVD’s subtitle language.

REVERSE/FORWARD SKIP buttons

7. Press to skip backwards or forwards.

STOP button

8. Press to stop a disc.

REVERSE/FORWARD SEARCH buttons

9. Press to search a disc backwards or forwards.

TV VOL button

10. TV volume adjustment.

MENU button

11. Brings up the HDD & DVD RECORDER’s setup menu. OK/DIRECTION buttons (

12.

▲▼◄► buttons)

PROG button

Use this to select a TV programme.

27.

TV MUTE/AUDIO button

In TV mode, this operates as sound mute. Use this to access various audio functions on a disc (DVD mode).

RETURN button

28.

EXIT button

29.

PLAY LIST/TITLE MENU button

30. Use this to return to the Title menu, or to view the recorded ﬁ les list.

TIMER button

31. Press to directly enter the Timer Recording Mode menu.

REC PAUSE/TIME SHIFT button

32. Use this to pause during recording. In TV mode, use this to operate Time shift function.

REC MODE button

33. Use this to set the desired Recording time and picture quality. (XP/SP/LP/EP).

Getting Started

English - 17

Connecting & Setting Up

Connecting the HDD & DVD RECORDER

This section involves various methods of connecting the HDD & DVD RECORDER to other external components and required initial setting modes.

You can connect your HDD & DVD RECORDER to the television using the SCART cable if the appropriate input is available on the television.

Connect the RF cable as shown.

1. Connect one end of the SCART cable to the AV1

Connecting & Setting Up

socket on the rear of the HDD & DVD RECORDER. Plug the other end into the appropriate connector

3. on the television. Plug in the HDD & DVD RECORDER and TV

4. Turn on the HDD & DVD RECORDER and TV.

5. Press the INPUT SEL. button on your TV remote

6. control until the Video signal from the HDD & DVD RECORDER appears on the TV screen.

Additional connections

You can connect your HDD & DVD RECORDER to a satellite or digital tuner.

External device (VCR/Satellite receiver)

To ANT INPUT

The RF cable connection of this product sends



only signals of TV. You must connect SCART cable or Audio/Video cables to watch a DVD from your HDD & DVD RECORDER.

TV mode : Press the TV/DVD button on



remote control, then “TV” appear on Front LED display (or turn off HDD & DVD RECORDER). Then you can watch programmes received through TV.

To RF IN

To TV

RF Cable

- DVD mode

Connect the AV2 connector of HDD & DVD

1. RECORDER and VCR/Satellite receiver or digital tuner using a SCART cable.

Connect the AV1 connector to the SCART AV

2. connector on TV.

Turn on the HDD & DVD RECORDER, VCR/

3. Satellite receiver or digital tuner and TV.

Set Input mode on AV2.

- TV mode

Press the TV/DVD button on remote control, then

1. “TV” appear on Front LED display. (or turn off HDD & DVD RECORDER.)

You can watch programmes from a satellite or

2. digital tuner connected to this HDD & DVD RECORDER, even when the HDD & DVD RECORDER is turned off.

English - 18

Other type of connecting the Audio output cable

Case 2 : Connecting to a stereo ampliﬁ er with AV output jacks

There are several ways to output audio signal not using scart cables. Select the audio connection that best suits you below.

•

Case 1 : Connecting to your TV

•

Case 2 : Connecting to a stereo ampliﬁ er with AV

output jacks

•

Case 3 : Connecting to an AV ampliﬁ er with a digital

output jack

Manufactured under licence from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

“DTS” and “DTS Digital Out” are trademarks of DTS, Inc.

Case 1 : Connecting to your TV

If your TV has audio input jacks, use this connection.

If your stereo ampliﬁ er only has AUDIO INPUT jacks (L and R), use the AUDIO OUT jacks

Connecting & Setting Up

WhiteRed

Yellow

White

Red

White

Yellow

Front(L) speaker

Front(R) speaker

English - 21

Case 3: Connecting to an AV ampliﬁ er with a digital output jack

If your AV ampliﬁ er has a Dolby Digital, MPEG2 or DTS decoder and a digital input jack, use this connection. To enjoy Dolby Digital, MPEG2 or DTS sound, you will need to set up the audio settings. According to your ampliﬁ er, connect to an optical cable or a coaxial cable. (See pages 30~31)

Connecting & Setting Up

Connecting to AV 3 IN, DV input jack

This allows you to connect your HDD & DVD RECORDER to other external devices and view or record their outputs.

•

Case 1 : Connecting a VCR, Set-Top Box(STB),

DVD player or Camcorder to the AV 3 IN jacks

•

Case 2 : Connecting a DV Device to the DV IN jack

Case 1 : Connecting a VCR, Set-Top Box(STB), DVD player or Camcorder to the AV 3 IN jacks

Connecting a VCR or external device to AV 3 IN jacks of the HDD & DVD RECORDER. You can record from connected equipment (VCR, STB, DVD player or Camcorder).

Rear (L)

Front (L)

Subwoofer

Centre

Front (R)

Rear (R)

Camcorder

VCR

Yellow

STB

DVD

Yellow

White

Red

AV 3 in selection will be automatically done.



White

If the input is not selected automatically, use INPUT SEL. button to select proper input.

Copy protected content cannot be recorded.



Red

English - 22

Case 2 : Connecting a Camcorder to the DV IN jack

If your digital camcorder has a DV output jack, connect it to the DV input jack of your HDD & DVD RECORDER.

Camcorder

If the input is not selected automatically, use



INPUT SEL. button to select proper input.

Connecting & Setting Up

English - 23

System Setup

HDD & DVD RECORDER Library

System Setup

HDD

MOVE

Title

Library

DivX

Timer Record

Music

Disc Manager

Photo

Setup

SELECT

Auto setup will be started.

Auto Setup

Please wait.

Yes No

Stop

RETURN

63%

On-Screen Menu Navigation

| | | |

EXIT

The on-screen menus allow you to enable or disable various functions on your HDD & DVD RECORDER. Press the MENU button to open the on-screen menu and then use the following buttons to navigate through the on screen menus.

▲▼, ◄►

buttons

Press these buttons on the remote control to move the selection bar

▲▼, ◄►

OK button

to cycle through the menu options.

Press this button on the remote control to conﬁ rm any new settings.

RETURN button

Press this button on the remote control to return to the Previous menu screen displayed or to exit the on-screen menu.

EXIT button

4. Press this button to exit the on-screen MENU.

Plug & Auto Setup

Your HDD & DVD RECORDER will automatically set itself up when it is plugged in for the ﬁ rst time. TV stations and clock will be stored in memory. The process takes a few minutes. Your HDD & DVD RECORDER will then be ready for use.

Connect the RF cable as indicated on page 18.

(Connecting Your HDD & DVD RECORDER to the TV Using the RF Cable and scart cable.)

Plug the HDD & DVD RECORDER into the mains. “AUTO” in the

front panel display ﬂ ickers.

Press the OK button to start the auto setup.

Auto channel scan will be started.

The number of stations automatically stored by the HDD & DVD

• RECORDER depends on the number of stations that it has found.

After auto channel scan is completed, auto clock setting will be

started automatically in 10 seconds. If you want to start auto clock setting immediately, press OK button. If you do not want to do auto

◄►

clock setting, select No using the button.

buttons, then press the OK

Auto channel scan completed successfully. Press the [OK] button to auto clock set.

Yes

English - 24

Please wait. Now setting the clock. If you want to

exit clock setting,

press the [MENU] button.

Clock Set

mo. da. yr. hr. min. Auto

JAN 01 2007 12 00 On

Monday

Wait until current date and time are displayed automatically. If you

want to exit auto clock setting, press MENU button.

Now, HDD & DVD RECORDER is ready for use. Function for



“Plug & Auto Setup” is ﬁ xed already. So if you want to change this ﬁ xed one, you can change it by Presetting the Stations in OSD “Channel Set - Manual Setup” menu. (See pages 26~27)

Auto setup function can be performed by pressing STOP (



on the unit continuously for 5 seconds or more during power off with no disc inserted.

Check the date and time.

If it is : Correct, press OK button then the date and time will be

• saved. If you don’t press the OK button, the date and time will be saved automatically after 5 seconds.

If it is : Incorrect, input correct Month, Day, Year, Hour or Minute

• using

▲▼, ◄►

buttons or number buttons. Press OK button then the date and time will be saved. When you need to change clock setting, you can set up it manually.

)

System Setup

HDD & DVD RECORDER Setup

HDD

MOVE

HDD & DVD RECORDER Setup

HDD

MOVE

HDD & DVD RECORDER Clock Set

HDD

MOVE

System

Library

Clock Set

Timer Record

Channel Set

Disc Manager

Language

Setup

Audio

Video

Parental Lock

SELECT

System

Library

Clock Set

Timer Record

Channel Set

Disc Manager

Language

Setup

Audio

Video

Parental Lock

SELECT

Library

Timer Record

mo. da. yr. hr. min. Auto

Disc Manager

JAN 01 2007 12 00 On

Setup

Monday

SELECT

RETURN

EXIT

Setting the Clock

| | | | | | |

This menu is used to set the current time. You need to set the time to use timer recording.

With the unit in Stop mode, press the MENU button.

Press the ▲▼ buttons to select Setup, then press the OK or ►

button.

▲▼

Press the

buttons to select Clock Set, then press the OK or ► button. Press the

▲▼◄►

buttons to input Month, Day, Year, Hour or Minute. Press the number buttons to input clock data directly. The day of the week is displayed automatically.

Press the OK button, then the date and time will be saved. If you

don’t press the OK button, it will not be saved.

You must have the RF cable connected to set the Auto Clock.



(See page 18)

The HDD & DVD RECORDER automatically sets the clock



according to the time signal broadcast between the channels PR1 to PR5. If you do not need the Auto Clock Set function, select Off.

English - 25

HDD & DVD RECORDER Channel Set

HDD

Library

Timer Record

Disc Manager

Setup

Auto Setup

Manual Setup

| |

Channel Set

Auto Setup

System Setup

MOVE

PR CH Name 01 002 - - - 02 004 - - - 03 - - - - - - 04 - - - - - - 05 - - - - - - 06 - - - - - - 07 - - - - - - -

SELECT

Auto Setup

Please wait.

Stop

Manual Setup

Edit Delete Swap

Manual Setup

PR 01

CH 002

Name - - - -

MFT

MOVE sSELECT

RETURN

Save

EXIT

RECORDER tuner band to Antenna or Cable, whichever you connected to the Antenna In jack during initial setup.

This feature allows you to manually set the HDD & DVD

With the unit in Stop mode, press the MENU button.

Press the ▲▼ buttons to select Setup, then press the OK or ►

button.

Press the ▲▼ buttons to select Channel Set, then press the OK or

►

button.

Press the ▲▼ buttons to select Auto Setup, then press the OK or

►

button. The message “Your data will be lost. Press [OK] to continue, [RETURN] to exit.” is displayed.

Press the OK button. Channel scan will be started.

The ﬁ rst frequency band is scanned and the ﬁ rst station found is

• displayed and stored. And the HDD & DVD RECORDER searches for the second station and so on.

The number of stations automatically stored by the HDD & DVD

• RECORDER depends on the number of stations that it has found.

Press the OK button to stop the Auto Setup



Manual Setup

You can add preset channel that Auto Channel Search missed. And you can delete a channel you wish to remove. You can programme the order of channels.

With the unit in Stop mode, press the MENU button.

▲▼

Press the button.

Press the ▲▼ buttons to select Channel Set, then press the OK or

►

button.

Press the ▲▼ buttons to select Manual Setup, then press the OK

or ► button.

Press the

delete, or swap, then press the COLOUR button. Select Edit, Delete or Swap.

In case of Edit (RED(A) button) : You can add or edit

• PR(programme) information. After change PR informations (CH., Name, MFT), select Save, then press the OK button.

- CH : Tune the channel using

- Name : Display station name automatically detected in

- MFT(Manual Frequency Tunning) : You can tune up the

channel frequency better using ◄► buttons.

In case of Delete (GREEN(B) button) : the channel information

• of selected PR(programme) will be removed.

buttons to select Setup, then press the OK or ►

▲▼

buttons to select a PR(programme) you wish to edit,

◄►

buttons.

broadcasting signal. If not detected, you can edit name by using

▲▼◄►

buttons.

English - 26

In case of Swap (YELLOW(C) button) : You can swap the

• channel information of two PR(programme). For example, if you wish to swap PR2 and PR5, select swap at PR2, then press the

OK button at PR5.

HDD & DVD RECORDER Language

HDD

MOVE

Audio : Original

Library

Subtitle : Automatic

Timer Record

Disc Menu : English

Disc Manager

Menu : English

Setup

SELECT

RETURN

| | | |

EXIT

Setting up the Language Options

If you set the language options, in advance, they will come up automatically every time you watch a movie.

With the unit in Stop mode, press the MENU button.

Press the then press the OK or ► button.

Press the then press the OK or ► button. Language setup menu will be displayed.

Press the

the OK or

•

Press the

5. the OK or

▲▼

buttons to select Setup,

▲▼

buttons to select Language,

▲▼

buttons to select the desired language option, press

►

button.

Audio : For the disc audio language.

Subtitle : For the disc subtitles.

Disc Menu : For the disc menu contained on the disc

Menu : For the on-screen menu of your HDD & DVD

RECORDER.

▲▼

buttons to select the desired language, then press

►

button.

If the selected language is not recorded on the disc, the



original pre-recorded language is selected.

The selected language will only appear if it is supported on the



disc.

System Setup

HDD & DVD RECORDER System

HDD

MOVE

Auto Power Off : Off

Library

Chapter Creator : Off

Timer Record

EP Mode Time : 6 Hours

Disc Manager

EZ Record : Off

Setup

DivX(R) Registration

SELECT

RETURN

EXIT

Setting up the System Options

| | | | |

This function allows you to setup the system setting.

With the unit in Stop mode, press the MENU button.

▲▼

Press the

buttons to select Setup, then press the OK or ►

button.

▲▼

Press the

buttons to select System, then press the OK or ►

button.

Press the ▲▼ buttons to select the desired system option, then

press the OK or ► button.

Press the ▲▼ buttons to select the desired item, then press the OK

►

button.

English - 27

HDD & DVD RECORDER System

HDD

MOVE

Auto Power Off : Off

Library

Chapter Creator : Off

Timer Record

EP Mode Time : 6 Hours

Disc Manager

EZ Record : Off

Setup

DivX(R) Registration

SELECT

Off 2 Hours 6 Hours

RETURN

EXIT

Auto Power Off Setting

| | | | |

This feature automatically turns off your HDD & DVD RECORDER, if you do not press any button for the selected time.

Press the ▲▼ buttons to select Auto Power Off, then press the OK

►

button.

Press the ▲▼ buttons to select the desired item, then press the OK

►

button.

Off : Auto power off is disabled.

•

2 Hours : HDD & DVD RECORDER will automatically turn off for

• 2 hours after the last button is pressed.

6 Hours : HDD & DVD RECORDER will automatically turn off for

• 6 hours after the last button is pressed.

If the turn off time set with the Auto Power off function is reached

•

during playback or recording, the device will operate until the playback or recording is ﬁ nished.

HDD & DVD RECORDER System

System Setup

DVD-RW(V)

MOVE

Auto Power Off : Off

Library

Chapter Creator : Off

Timer Record

Disc Manager

Setup

SELECT

Jan/1/2007 17:30 PR1

Previous Top Next

CHAPTER 1/1

Previous Top Next

Off On

EP Mode Time : 6 Hours

EZ Record : Off

DivX(R) Registration

RETURN

Jan/1/2007 17:30 PR1

Automatic Chapter Creator

| | | | |

(V-mode)

A DVD-Video consists of ‘Titles’ and ‘Chapters’.

EXIT

1/1

When you record one programme, it makes one Title. If you use this function, the Title will be divided into Chapters.

▲▼

Press the

buttons to select Chapter Creator, then press the

OK or ► button.

Press the ▲▼ buttons to select Off or On, then press the OK or ►

button.

Off : Select if you do not want use Automatic Chapter Creator.

•

Select this option to use the Automatic Chapter Creator feature.

On :

•

Press the EXIT ( ) button to exit the menu.

Press the REC button to start recording.

(See page 58 about how to set recording speed) The message “Do you want to create the chapter menu after this recording?” is displayed.

◄►

Press the

A new chapter is created according to the selected recording

•

buttons to select OK, then press the OK button.

mode. A chapter will be about 5 minutes long in XP and SP, and about 15 minutes long in LP and EP mode.

Press the STOP button to stop recording.

To display the created titles, ﬁ nalise the disc (See page 94) and then

press the TITLE MENU button. The title menu will be displayed.

To display the created chapters, select the desired Title and then

press the DISC MENU button. The chapter menu for the selected Title will be displayed.

The Automatic Chapter Creator function does not work during



Timer Recording or when you turn the power off.

English - 28

HDD & DVD RECORDER System

HDD

MOVE

Auto Power Off : Off

Library

Chapter Creator : On

Timer Record

EP Mode Time : 6 Hours

Disc Manager

EZ Record : Off

Setup

DivX(R) Registration

SELECT

6 Hours 8 Hours

RETURN

EXIT

EP Mode Time Setting

| | | | |

You can select one of four recording modes by pressing the REC MODE button repeatedly. EP mode is one of four REC Mode (XP, SP, LP, EP). In EP(Extended Play) mode, you can set recording time to 6 or 8 hours with this setting.

6 Hours

•

8 Hours

•

HDD & DVD RECORDER System

HDD

MOVE

Auto Power Off : Off

Library

Chapter Creator : Off

Timer Record

EP Mode Time : 6 Hours

Disc Manager

EZ Record : Off

Setup

DivX(R) Registration

SELECT

Disc Initialise (DVD-V) Now, initialising..

Finalisation...

Off On

RETURN

EXIT

50%

EZ Record

| | | | | |

(V-mode)

This function allows you Initialise and Finalise a disc automatically.

Press the ▲▼ buttons to select EZ Record, then press the OK or

button.

Press the ▲▼ buttons to select On, then press the OK or ► button.

Press the EXIT ( ) button to exit the menu.

Insert a disc.

If the disc is new, it will initialise automatically.

Press the REC button.

EZ Record function will automatically Finalise the disc under the

following conditions.

When you press the OPEN/CLOSE button on your HDD & DVD

•

RECORDER after recording on at least 70% of the disc. The tray will open after the disc has been ﬁ nalised.

The above feature is available only when a DVD-RW(V) or

•

DVD-R disc is inserted.

►

System Setup

HDD & DVD RECORDER System

HDD

Auto Power Off : Off

Library

DivX(R) Video On Demand

Chapter Creator : Off

Timer Record

EP Mode Time : 6 Hours

Your registration code is: XXXXXXXX

Disc Manager

EZ Record : Off

To learn more visit www.divx.com/vod Setup

DivX(R) Registration

SELECT

RETURN

EXIT

If you insert a new DVD-RW disc, it will be formatted in V mode



after auto initialising.

If you select off, you must initialise (see page 57) and ﬁ nalise



the disc manually in the Disc Manager menu.(see page 94)

The length of Recording is different according to recording



mode. (see page 36)

DivX(R) Registration

| | | | |

Please use the Registration code to register this HDD & DVD RECORDER with the DivX(R) Video On Demand format. For more information, visit www.divx.com/vod

English - 29

HDD & DVD RECORDER Setup

System Setup

HDD

Library

Timer Record

Disc Manager

MOVE

Setup

System

Clock Set

Channel Set

Language

Audio

Video

Parental Lock

SELECT

RETURN

Setting up the Audio Options

| | | | | | |

EXIT

You can connect the HDD & DVD RECORDER to an external amp or Home theatre. Allows you to setup the Audio device and sound status depending on the audio system in use. You can also set NICAM mode.

With the unit in Stop mode, press the MENU button.

▲▼

Press the

buttons to select Setup, then press the OK or ►

button.

Press the ▲▼ buttons to select Audio, then press the OK or ►

button.

▲▼

Press the

buttons to select the desired audio option, then press

the OK or ► button.

Press the

▲▼

buttons to select the desired item, then press the OK

or ► button.



Press the RETURN or

◄

button to return to the previous menu. Press the EXIT ( ) button to exit the menu.

HDD & DVD RECORDER Audio

HDD

MOVE

HDD & DVD RECORDER Audio

HDD

MOVE

Library

Timer Record

Disc Manager

Setup

SELECT

Library

Timer Record

Disc Manager

Setup

SELECT

Digital Output : PCM

PCM

DTS : Off

Bitstream

DRC : On

NICAM : On

V-Mode Compatibility : Off

Digital Output : PCM

DTS : Off

DRC : On

NICAM : On

V-Mode Compatibility : Off

RETURN

Off On

RETURN

EXIT

Digital Output

| | | | |

PCM : Select this when your equipment is not decode Dolby Digital

• compatible.

Bitstream : Outputs Dolby Digital (or MPEG-2) audio as bitstream.

•

Select this when your AV receiver or AV ampliﬁ er has a Dolby Digital (or MPEG-2) Decoder.

Digital output setting is equally applied to both Dolby Digital



and MPEG-2 audio. LPCM sound track is always outputted as PCM. It has no relation with Digital Output setting.



Be sure to select the correct Digital Output or you will hear no sound or a loud noise.

DTS

| | | | |

Off : Doesn’t output DTS signal. Select this when your AV receiver

•

(or AV ampliﬁ er) does not have DTS decoder.

•

On : Outputs DTS Bitstream via digital output when you play DTS

track. Select this only when your AV receiver (or AV ampliﬁ er) have DTS decoder.



When DTS soundtrack is played, sound does not output from

AV Audio Output.

English - 30

+ 71 hidden pages