Samsung DVD-HR730 User Manual [nl]

Instruction Manual

DVD-HR730 DVD-HR732 DVD-HR734

English

www.samsung.com/za

AK68-01025U

Warning

IMPORTANT NOTE

The mains lead on this equipment is supplied with a moulded plug incorporating a fuse.The value of the fuse is indicated on the pin face of the plug.If it requires replacing, a fuse approved to BS1362 of the same rating must be used.

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING T O QUALIFIED SERVICE PERSONNEL.

Getting Started

This symbol indicates “dangerous voltage” inside the product that presents a risk of electric shock or personal injury.

This symbol indicates important instructions accompanying the product.

Do not install this equipment in a confined space such as a bookcase or similar unit.

WARNING :

CAUTION :HDD & DVD RECORDER USES AN INVISIBLE

CAUTION

THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture.

LASER BEAM WHICH CAN CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED.BE SURE TO OPERATE HDD & DVD RECORDER CORRECTLY AS INSTRUCTED.

Never use the plug with the fuse cover omitted if the cover is detachable.If a replacement fuse cover is required, it must be of the same colour as the pin face of the plug. Replacement covers are available from your dealer.

If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should obtain a suitable safety approved extension lead or consult your dealer for assistance.

However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect the plug to a mains jack, as there is a risk of shock hazard from the bared flexible cord.

The product unit accompanying this user manual is licenced under certain intellectual property rights of certain third parties.This licence is limited to private noncommercial use by end-user consumers for licenced contents. No rights are granted for commercial use. The licence does not cover any product unit other than this product unit and the licence does not extend to any unlicenced product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit.The licence only covers the use of this product unit to encode and/or decode audio files conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this licence for product features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.

2- English

Precaution

Important Safety Instructions

Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings, Install in accordance with the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades with one wider than the other.A groundingtype plug has two blades and a third grounding prong.The wide blade or the third prong are provided for your safety.if the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer .

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Handling Cautions

• Before connecting other components to this HDD & DVD RECORDER, be sure to turn them all off.

• Do not move the HDD & DVD RECORDER while a disc is being played, or the disc may be scratched or broken, the HDD & DVD RECORDER inter nal parts may be damaged.

•

Do not put a flower vase filled with water or any small metal objects on the HDD & DVD RECORDER.

• Be careful not to put your hand into the disc tray.

• Do not place anything other than the disc in the disc tray.

• Exterior interference such as lightning and static electricity can affect normal operation of this HDD & DVD RECORDER.If this occurs, turn the HDD & DVD RECORDER off and on again with the STANDBY/ON button, or disconnect and then reconnect the AC power cord to the AC power outlet.The HDD & DVD RECORDER will operate normally.

• Be sure to remove the disc and turn off the HDD & DVD RECORDER after use.

• Disconnect the AC power cord from the AC outlet when you don’t intend to use the HDD & DVD RECORDER for long periods of time.

• Clean the disc by wiping in a straight line from the inside to the outside of the disc.

Maintenance of Cabinet

For safety reasons, be sure to disconnect the AC power cord from the AC outlet.

•

Do not use benzene, thinner, or other solvents for cleaning.

•

Wipe the cabinet with a soft cloth.

HDD (Hard Disk Drive)

The hard disk has a high storage density, which enables long recording durations and quick access to written data. However, it can easily be damaged by shock, vibration or dust and should be kept away from magnets.To avoid losing important data, observe the following precautions.

• Do not use the HDD & DVD RECORDER in a place subject to extreme changes in temperature.

• Do not apply a strong shock to the HDD & DVD RECORDER.

• Do not place the HDD & DVD RECORDER in a location subject to mechanical vibrations or in an unstable location.

English - 3

Getting Started

• Do not place the HDD & DVD RECORDER on top of a heat source.

• Do not disconnect the AC power cord while the power is on.

• Do not attempt to change the hard disk.This may result in a malfunction.

Should the hard disk be damaged, you cannot recover lost data.The hard disk is only a temporary storage space.

• Do not apply labels or stickers to discs.(Do not use discs fixed with exposed tape adhesive or leftover peeled-off stickers.)

• Do not use scratch-proof protectors or covers.

• Do not use discs printed with label printers available on the market.

• Do not load warped or cracked discs.

Getting Started

Disc Handling

• Use discs with regular shapes. If an irregular disc (a disc with a special shape) is used, this HDD & DVD RECORDER may be damaged.

Holding discs

• Avoid touching the surface of a disc where recording is performed.

DVD-RAM, DVD-RW and DVD-R

• Clean with an optional DVD-RAM/PD disc cleaner (LF-K200DCA1 where available).Do not use cleaners or cloths for CDs to clean DVD-RAM/

-RW/-R discs.

DVD-Video, Audio-CD

• Wipe off dirt or contamination on the disc with a soft cloth.

Disc Storage

Be careful not to harm the disc because the data on these discs is highly vulnerable to the environment.

• Do not keep under direct sunlight.

• Keep in a cool ventilated area.

• Store vertically.

• Keep in a clean protection jacket.

• If you move your HDD & DVD RECORDER suddenly from a cold place to a warm place, condensation may generate on the operating parts and lens and cause abnormal disc playback. If this occurs, do not connect the plug to the power outlet and wait for two hours. Then insert the disc and try to play back again.

Disc Specifications

Disc Type

DVD-Video

• A digital versatile disc (DVD) can contain up to 135minutes of images, 8 audio languages and 32 subtitle languages. It is equipped with MPEG-2 picture compression and Dolby digital surrounding, allowing you to enjoy vivid and clear theatre quality images in the comfort of your own home.

• When switching from the first layer to the second layer of a dual-layered DVD Video disc, there may be momentary distortion in the image and sound. This is not a malfunction of the unit.

• Once a DVD-RW/-R recorded in Video Mode is finalised, it becomes DVD-Video.

Cautions on handling discs

• Do not write on the printed side with a ball-point pen or pencil.

• Do not use record cleaning sprays or antistatic. Also, do not use volatile chemicals, such as benzene or thinner.

4- English

Audio CD

DVD-RW Disc Playback and Recording

• An audio disc on which 44.1kHz PCM Audio is recorded.

• Plays CD-DA format audio CD-R and CD-RW discs.

• The unit may not be able to play some CD-R or CD-RW discs due to the condition of the recording.

CD-R/-RW

• Use a 700MB(80 minutes) CD-R/-RW disc. If possible, do not use a 800MB(90 minutes) or above disc, as the disc may not play back.

• If the CD-R/-RW disc was not recorded as a closed session, you may experience a delay in the early playback time, all recorded files may not play.

• Some CD-R/-RW discs may not be playable with this unit, depending on the device which was used to burn them. For contents recorded on CD-R/-RW media from CDs for your personal use, playability may vary

depending on contents and discs.

DVD-R Disc Playback and Recording

• Once a DVD-R recorded in Video Mode is finalised, it becomes DVD-Video.

• You can record onto the available space on the disc and perform editing functions such as giving titles to discs and programmes and erasing programmes before finalising.

• When programming is erased from a DVD-R, that space does not become available. Once an area on a DVD-R is recorded on, that area is no longer available for recording, whether the recording is erased or not.

• It takes about 30 seconds for the unit to complete recording management information after recording finishes.

• This product optimizes the DVD-R for each recording. Optimizing is carried out when you start recording after inserting the disc or turning on the unit. Recording onto the disc may become impossible if optimizing is carried out too many times.

• Playback may be impossible in some cases due to the condition of recording.

• This unit can play back DVD-R discs recorded and finalised with a Samsung DVD video recorder. It may not be able to play some DVD-R discs depending on the disc and the condition of the recording.

• Recording and playback can be performed on DVDRW discs in both the Video and VR Modes.

• Once a DVD-RW recorded in both the Video and VR Modes is finalised, you cannot perform additional recording.

• Once a DVD-RW recorded in Video Mode is finalised, it becomes DVD-Video.

• In both modes, playback can be performed before and after finalisation, but additional recording, deleting and editing can not be performed after finalisation.

• If you want to record the disc in VR Mode and then record in V Mode, be sure to execute Format. Be careful when executing For mat because all the recorded data may be lost.

• A DVD-RW blank disc is initialized to VR Mode when first initialized.

DVD-RAM Disc Playback

• You cannot play a DVD-RAM in most DVD components due to compatibility issues.

• Only DVD-RAM standard Version 2.0. discs can be played in this unit.

• For cartridge type DVD-RAM discs, remove the cartridge and use the disc only.

Disc Copy

Contents Copy Specifications

Contents HDD Recorded Video Title Supported Supported Copy Protected Title Not supported Not supported

Copy Once

MP3 Supported supported JPEG(photo) Supported supported DivX Supported Supported

Once "Copy Once programme" has been recorded on the DVD disc, this title cannot be copied to HDD anymore. But "Copy Once programme" has been recorded on the HDD, this title can be copied to DVD-RW(VR mode).

Title

➞ DVD DVD ➞

Move

(Deletes the Title in the

HDD after copying)

Not supported

HDD

Getting Started

English - 5

COPY PROTECTION

• Many DVD discs are encoded with copy protection. Because of this, you should only connect your HDD & DVD RECORDER directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy-protected DVD discs.

• This product incorporates copyright protection technology that is protected by methods claims of certain U.S. patents and other intellectual

Getting Started

property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorised by Macrovision Corporation, is intended for home and other limited viewing uses only unless otherwise authorised by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Protection

This HDD & DVD RECORDER can allow you to protect the contents of your discs, as described below.

• Programme-protected: See page 87 “Locking(Protecting) a Title”

• Disc-protected: See page 112 “Disc Protection”

❋

DVD-RW/-R discs that are incompatible with the DVD-VIDEO for mat cannot be played with this product.

❋

For more information on DVD recording compatibility, consult your DVD-RW/-R manufacturer.

❋

Use of poor quality DVD-RW/-R discs may cause following unexpected problems including, without limitation, recording failure, loss of recorded or edited materials or damage to the HDD & DVD RECORDER.

Using JPEG disc

• CD-R/-RW, DVD-RAM/-RW/-R recorded with UDF, ISO9660 or JOLIET format can be playbacked.

• Only JPEG files with the “.jpg” or “.JPG” extension can be displayed.

• The unit can handle a maximum of 500 files and 100 sub folders under a folder.

• MOTION JPEG and progressive JPEG are not supported.

Using MPEG4 disc

• Disc : CD-R/-RW, DVD-RAM/-RW/-R

• MPEG4(DivX) File with following extensions can be played.: .avi, .divx, .AVI, .DIVX

• DivX Video (Codec) Format : DivX 3.11 DivX 4.x DivX 5.x (without QPEL and GMC)

•

DivX Audio (Codec) Format : MP3, MPEG1 Audio Layer 2, Windows Media Audio, LPCM, AC3

• Supported subtitle file formats: .smi, .srt, .sub, .psb, .txt, .ass

• The unit can handle a maximum of 500 files and 100 sub folders under a folder.

DVD-RW (VR)

• This is a format that is used for recording data on a DVD-RW disc. You can record multiple titles, edit, delete, partial delete, create a playlist, etc.

• A disc that is recorded in this mode may not be played by existing HDD & DVD RECORDER.

DVD-RW (V)/-R

Disc Format

Using MP3 disc

• CD-R/-RW, DVD-RAM/-RW/-R, HDD with MP3 files recorded with UDF, ISO9660 or JOLIET format can be playbacked.

• Only MP3 files with the “.mp3” or “.MP3” extension can be played.

• For MP3 files recorded with a VBR(Variable Bit Rates), from 32 Kbps to 320 Kbps, the sound may cut in out.

• Playable bit-rate range is from 56 Kbps to 320 Kbps.

• The unit can handle a maximum of 500 files and 100 sub folders under a folder.

6- English

• This is a format that is used for recording data on a DVD-RW or DVD-R disc.The disc can be played by existing HDD & DVD RECORDER once it has been finalised.

• If a disc that has been recorded in Video Mode by a different maker’s recorder but has not been finalised, it cannot be played or additionally be recorded by this HDD & DVD RECORDER.

Do not use the following discs!

• LD, CD-G, CD-I, CD-ROM and DVD-ROM discs should not be used in this product. [Note] Disc types that can be played :CD/CD-R/-RW/ MP3/JPEG/DVD-Video/DVD-RAM/-RW-R. For a DVD-RW/-R disc, which has been recorded in Video Mode on another component, it can play only when finalised.

• Some commercial discs and DVD discs purchased outside your region may not be playable with this product.When these discs are played, either “No disc.” or “Please check the regional code of the disc.” will be displayed.

• If your DVD-RW disc is an illegal copy or is not in DVD video format, it may also not be playable.

Disc compatibility

• High Speed Recording discs can be used in this unit.

• Not all brands of discs will be compatible with this unit.

Getting Started

English - 7

Contents

Connecting to A V 1 IN,AV 2 IN, DV input jack

Connecting a VCR, Set-Top Box(STB) or DVD player to the AV 1 IN jacks Connecting a Camcorder to the AV 2 IN jacks Connecting a Camcorder to the DV IN jack

...........................23

.........23

..............23

...23

Getting Star

Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Getting Started

Precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . .3

Handling Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Maintenance of Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . .3

HDD (Hard Disk Drive) . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Disc Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Disc Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Disc Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Disc Copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

General Features . . . . . . . . . . . . . . . . . . . . . . . . . .10

Before Reading the User’s Manual . . . . . . . . . . .11

How to use the HDD & DVD RECORDER . . . . . .11

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Front Panel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Tour of the Remote Control . . . . . . . . . . . . . . . . . . . . . .17

Connecting & Setting Up

ted

System Setup

On-Screen Menu Navigation..................................24

Plug & Auto Setup...................................................25

Setting the Clock......................................................26

Presetting Channels with

the Auto Setup function..........................................27

Presetting Channels with

the Manual Setup function.....................................28

Setting up the Language Options.........................29

Auto Power Off Setting...........................................30

Setting up the Quick Recording Options............31

Automatic Chapter Creator....................................32

DivX(R) Registration................................................33

CM Skip Time Setting..............................................33

EP Mode Time Setting.............................................34

Setting up the Audio Options................................35

Setting up the Video display Options...................37

Setting up the Progressive scan...........................37

Canceling the Progressive scan...........................38

Setting up the Parental Lock.................................39

If you forgot your password.............................................40

Setting the Rating Level..................................................40

Changing the Password..................................................40

Quick Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Connecting the HDD & DVD RECORDER . . . . . .19

Other type of connecting the Video output cable

Case 1 : Connecting to a Video (Composite)

output jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Case 2 : Connecting to an S-Video output jack . . . . . .20

Case 3 : Component Video output jacks . . . . . . . . . . . .21

Other type of connecting the Audio output cable

Case 1 : Connecting to your TV . . . . . . . . . . . . . . . . . .21

Case 2 : Connecting to a stereo amplifier

with AV output jacks . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Case 3: Connecting to an AV amplifier

with a digital output jack . . . . . . . . . . . . . . . . . . . . . . . .22

. .19

. . . .21

8- English

Pla

ybackk

Pla

ybac

Before Playing..........................................................41

Playing a Disc...........................................................42

Using the Disc Menu & Title Menu........................43

Using the Search & Skip Functions.....................43

Slow Motion Play/Step Motion Play......................44

About ANYKEY ........................................................45

Playing the Title List ................................................46

Navigation menu......................................................47

Using Markers ..........................................................50

Using the Bookmarks .............................................52

Selecting the Subtitle Language...........................53

Selecting the Soundtracks & Audio channels....54

Changing the Camera Angle .................................55

Repeat Play...............................................................56

Zooming-In................................................................57

Select Media..............................................................58

Playing an Audio CD/MP3......................................58

Viewing a Picture.....................................................65

Playing an MPEG4...................................................69

Recor

ding

Before Recording.....................................................71

Recording the current TV programme

you are watching......................................................73

Recording from external equipment

you are watching......................................................75

Copying from a Camcorder....................................76

Making a One Touch Recording (OTR).................77

Simultaneous Recording and Playback...............78

Making a Timer Recording .....................................79

Editing the Scheduled List.....................................81

Deleting a Scheduled List ......................................82

Go T o Recorded List................................................83

Deleting an Undesired Title from the Copy List...........105

Previewing a Selected Title from the Copy List...........106

Selecting Record Mode of Each Title from

the Copy List..................................................................106

Changing Record Mode of All Titles from

the Copy List..................................................................107

Copying from DVD to HDD..................................107

Copying MP3, JPEG or Divx................................109

File Copy........................................................................109

Folder Copy...................................................................110

Disc Manager.........................................................111

Editing the Disc Name..................................................111

Disc Protection ..............................................................112

Formatting a Disc..........................................................112

Delete All Title Lists/DivX Lists /

Music Lists/Photo Lists .................................................113

Delete All Title Lists.......................................................114

Finalising a Disc............................................................115

Unfinalising a Disc (V/VR mode)..................................116

Ref

erence

Ref

erence

T r oubleshooting.....................................................117

Specifications ........................................................121

Getting Started

Editing

Basic Editing (Title List).........................................86

Renaming(Labeling) a Title.............................................86

Locking (Protecting) a Title ............................................87

Deleting a Title.................................................................88

Splitting a Section of a Title (Split)..................................89

Deleting a Section of a Title (Partial Delete)..................90

Advanced Editing (Playlist)....................................92

Creating a Playlist............................................................92

Playing Entries in the Playlist..........................................94

Renaming a Playlist Entry...............................................94

Editing a Scene for the Playlist.......................................95

Deleting a Playlist Entry from the Playlist....................100

Copying from HDD to DVD..................................101

About the Copy Screen.................................................101

Changing the Record Mode.........................................103

Copying Multiple Titles at One Time ..................104

English - 9

General Features

Automated Quality Adjustment for Timer Recording

If FR mode is selected, the video quality is adjusted automatically so that all video for the scheduled time can be recorded onto the free disc space. (See page 80)

The HDD(Hard Disk Drive) & DVD RECORDER allows you to record and play high quality digital video on DVDRW/-R discs or on the HDD.You can also edit digital images on DVD-RW discs or HDD.

Getting Started

HDD Recording

• DVD-HR730

You can record up to 127 hours of video (in EP mode) on the internal 80GB (gigabyte) hard disk (HDD).

• DVD-HR732 / DVD-HR734

You can record up to 272 hours of video (in EP mode) on the internal 160GB (gigabyte) hard disk (HDD).

With both recordable DVD and a high-capacity HDD in the same recorder, you have the flexibility to keep recordings on the HDD for quick access anytime, or record to DVD for archiving or playing on other DVD players.

Copy between HDD and DVD

You can copy recordings from the HDD to recordable DVD, or from DVD to the HDD. Usually you can use the high speed copy feature. You can also choose to copy material at a different recording quality from the original. For example, you might want to copy at XP mode (highest quality) recording on the HDD to SP (standard play) quality on a DVD so that you can fit other recordings on the same disc.

Creating a DVD video title using DVD-RW/-R disc

With the HDD & DVD RECORDER, you can create your own DVD Video titles on 4.7 GB DVD-RW/-R discs.

Copying data from a digital camcorder using a DV input jack

Record DV Device video onto HDD and DVD-RW/-R discs using the DV input jack (IEEE 1394-4pin/4pin). (See page 76)

High quality progressive scan

Progressive scanning provides high resolution and flicker free video.The 10-bit 54-MHz DAC and 2D Y/C Separating Circuitry provides the highest image playback and recording quality. (See pages 37~39)

A variety of functions with an easy-to-use user interface

The integrated menu system allows you to perform desired operations both easily and conveniently.With a HDD,

DVD-RW disc, you can edit recorded video, create a playlist, edit video in a specific sequence according to your requirements.

Simultaneous Recording and Playback

Playback and recording for both the DVD and the built-in hard disk drive (HDD) are completely independent.For example you can record a broadcast programme to either a recordable DVD or the HDD, while watching another recording you already made on the same DVD or on the HDD.

High quality digital audio and video recording and playback

Record up to 8-hours of video with a 4.7 GB DVD-RW/-R disc, depending on the recording mode.

Selectable Recording Mode

You can set your HDD & DVD RECORDER to one of four different recording speeds, each varying in recording quality and length. EP (6Hr or 8Hr) mode yields the most recording time, LP & SP modes provide less recording time with higher quality recording, XP mode gives you the highest quality recording.

10 - English

MPEG4 playback

This HDD & DVD RECORDER can play MPEG4 formats within an avi file.

DivX Certification

DivX, DivX Certified, and associated logos are trademarks of DivXNetworks, Inc and are used under licence.

Before Reading the User’s Manual

Make sure to check the following terms before reading the user manual.

Getting Started

Icons that will be used in manual

Icon Term Definition

HDD

DVD

RAM

JPEG on CD-R/-RW or DVD-R/-RW/

MP3

MPEG4 on CD-R/-RW or DVD-R/-RW/

Caution function does not operate or

NOTE on the page that help each

One-Touch

button by using only one button.

ANYKEY A function that can be operated

button by using ANYKEY button.

This involves a function available on the HDD.

This involves a function available on DVD or DVD-R/DVD-RW discs that have been recorded and finalised in Video Mode.

This involves a function available on DVD-RAM.

This involves a function available on DVD-RW.

This involves a function available on DVD-R.

This involves a function available on a data CD (CD-R or CD-RW).

This involves a function available

-RAM discs. This involves a function available

on CD-R/-RW or DVD-R/-RW/

-RAM discs. This involves a function available

-RAM discs. This involves a case where a

settings may be cancelled. This involves tips or instructions

function operate. A function that can be operated

How to use the HDD & DVD RECORDER

Step 1

This unit can record on the following types of discs. If you want to repeatedly record on the same disc or you want to edit the disc after recording, select a rewritable DVD-RW type disc. If you want to save a recording without any changes, choose a nonrewritable DVD-R. You can record files directly to the built-in HDD or edit a recorded file.

Step 2

Unlike a VCR, the HDD & DVD RECORDER automatically starts formatting when an unused disc is inserted. This is required for the preparation of recording on a disc.

Using the HDD

Formatting unneccessory.

Using a DVD-RW

This type of disc can be formatted in either DVD-Video format (V mode) or DVD-Video Recording for mat (VR mode). For an unused disc, a message that asks whether to initialize a disc or not. If you select “Yes”, disc will be formatted in VR mode. You can play a Video mode disc on various DVD components. A VR mode disc allows more varied editing.

Using a DVD-R

Formatting disc is unnecessary and only V Mode Recording is supported.You can play these type of discs on various DVD components only when they have been finalised.

Select the disc type or HDD

Format the disc to start recording

About the use of this user’s manual

1) Be sure to be familiar with Safety Instructions before using this product.(See pages 2~7)

2) If a problem occurs, check the Troubleshooting. (See pages 117~120)

English - 11

■

You can only use either the VR or Video

NOTE

mode on a DVD-RW, but not both at the same time.

■

You can change the DVD-RW to format to another format by reinitializing. It should be noted that the disc's data will be lost when changing formats.

Getting Started

Step 3

There are two different recording methods, Direct Recording and Timer Recording.Timer recording is classified as follows:

Recording mode : XP (high quality mode), SP (standard quality mode), LP (long recording mode), and EP (extended mode) according to the recording mode.When recording is set in the FR mode, the best quality picture is recorded with regards to the remaining time on the disc.

Step 4

You can select the title you want to play in a displayed menu and then immediately start playback.

A DVD consists of sections, called titles, and subsections, called chapters.

During recording, a title is created between two points where you start and stop recording. Chapters will be created automatically when you finalise recording on DVD-RW/-R discs in Video mode. The chapter’s length (interval between chapters) varies according to the recording mode.

Recording

Playing

Step 5

Editing on discs is easier than conventional video tapes.The HDD & DVD RECORDER supports many different edit functions, possible only with DVDs and HDD.

With a simple and easy edit menu, you can operate various edit functions, such as delete, copy, rename, lock, etc., on a recorded title.

Creating a playlist (DVD-RW in VR mode, HDD)

With this HDD & DVD RECORDER, you can create a new playlist on a disc and edit it without the original, pre-existing recording.

Editing a recorded disc

Finalising & Playing on

Step 6

To play your DVD on other DVD components, finalising may be necessary. First, finish all editing and recording operations, then finalise the disc.

When using a DVD-RW disc in VR Mode

DVD discs recorded in VR mode can only be played back in DVD recorders, not players.

When using a DVD-RW disc in Video Mode

The disc should be finalised first to enable playback on anything other than this HDD & DVD RECORDER. No more editing or recording can be made on the disc once it has been finalised. To enable recording on the disc again, the disc must be unfinalised.

When using a DVD-R disc

You should finalise the disc to play it on a component other than this HDD & DVD RECORDER.You cannot edit or record on the disc once it has been finalised.

other DVD components

12 - English

Unpacking

Getting Started

Accessories

Check for the supplied accessories below.

Video/Audio Cable RF Cable for TV

Batteries for Remote

Remote Control

Instruction Manual

Control (AAA Size)

Quick Guide

Setting the Remote Control

You can control certain functions of another manufacturer’s TV with this remote control. Control function buttons involve: TV

PROG INPUT SEL. button.

, VOL + – , Number buttons,TV MUTE,

STANDBY/ON,

Preparing the Remote Control

Install Batteries in the Remote Control

•

Open the battery cover on the back of the remote control.

•

Insert two AAA batteries. Make sure that the polarities (+ and –) are aligned correctly.

•

Replace the battery cover.

If the remote does not operate properly:

•

Check the polarity + – of the batteries (Dry-Cell) Check if the batteries are drained.

•

Check if remote sensor is blocked by obstacles.

•

Check if there is any fluorescent lighting nearby.

Dispose of batteries according to local environmental regulations. Do not put them in the household trash.

English - 13

To determine whether your television is compatible, follow the instructions below.

1. Switch your television on.

2. Point the remote control towards the television.

3. Press and hold the TV STANDBY/ON button and enter the two-figure code corresponding to the brand of your television, by pressing the appropriate number buttons.

Controllable TV Codes

BRAND BUTTON SAMSUNG 01, 02, 03, 04, 05, 06, 07, 08, 09

Getting Started

AIWA 82 ANAM 10, 11, 12, 13, 14, 15, 16, 17, 18 BANG & OLUFSEN 57 BLAUPUNKT 71 BRANDT 73 BRIONVEGA 57 CGE 52 CONTINENTAL EDISON 75 DAEWOO EMERSON 64 FERGUSON 73 FINLUX 06, 49, 57 FORMENTI 57 FUJITSU 84 GRADIENTE 70 GRUNDIG 49, 52, 71 HITACHI 60, 72, 73, 75 IMPERIAL 52 JVC 61, 79 LG 06, 19, 20, 21, 22, 78 LOEWE 06, 69 LOEWE OPTA 06, 57 MAGNAVOX 40 METZ 57 MITSUBISHI 06, 48, 62, 65 MIVAR 52, 77 NEC 83 NEWSAN 68 NOBLEX 66 NOKIA 74 NORDMENDE 72, 73, 75 PANASONIC 53, 54, 74, 75 PHILIPS 06, 55, 56, 57 PHONOLA 06, 56, 57 PIONEER 58, 59, 73, 74 RADIOLA 06, 56 RADIOMARELLI 57 RCA 45, 46 REX 74 SABA 57, 72, 73, 74, 75 SALORA 74 SANYO 41, 42, 43, 44, 48 SCHNEIDER 06

19, 20, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34

BRAND BUTTON SELECO 74 SHARP 36, 37, 38, 39, 48 SIEMENS 71 SINGER 57 SINUDYNE 57 SONY 35, 48 TELEAVA 73 TELEFUNKEN 67, 73, 75, 76 THOMSON 72, 73, 75 THOMSON ASIA 80, 81 TOSHIBA 47, 48, 49, 50, 51, 52 WEGA 57 YOKO 06 ZENITH 63

Result: If your television is compatible with the

remote control, it will switch off. It is now programmed to operate with the remote control.

■

If several codes are indicated for your

NOTE

television brand, try each one in turn until you find one that works.

■

If you replace the remote control's batteries, you must set the brand code again.

Then you can control the television using the following buttons after pressing the TV button.

Button Function TV STANDBY/ON Used to switch the television on and off. INPUT SEL. Used to select an external source. VOL (+ -) Used to adjust the volume of the television. PROG ( ) Used to select the desired channel. TV MUTE Used to toggle the sound on and off. Number Used to input number directly.

■

The functions listed above will not necessarily

NOTE

work on all televisions.If you encounter problems, operate the television directly.

14 - English

Description

Front Panel

< DVD-HR730 / DVD-HR732 >

< DVD-HR734 >

Getting Started

1. STANDBY/ON BUTTON

Turns the HDD & DVD RECORDER on and off.

2. DISC TRAY

Opens to accept a disc.

3. OPEN/CLOSE BUTTON

Opens and closes the disc tray.

4. DISPLAY

Displays the playing status, time, etc.

5. PLAY/PAUSE BUTTON

Plays a disc or pauses playback.

6. SEARCH/SKIP BUTTONS

Goes to the next title/chapter/track or goes back to the previous title/chapter/track.

7. AV 2 INPUT

Connect external equipment.

8. DV-INPUT

Connect external digital equipment with a DV jack. (such as a camcorder)

9. P.SCAN BUTTON

Selects the progressive scan mode.

10. DVD BUTTON

Select DVD mode.

11. HDD BUTTON

Select HDD mode.

12. PROG BUTTONS

Select TV preset Channels.Same as PROG button on the remote control.

13. REC BUTTON

Starts recording.

14. STOP BUTTON

Stops disc playback.

English - 15

Rear Panel

Getting Started

Fan

The fan always revolves when the power is on. Ensure a minimum of 10cm clear space on all sides of the fan when installing the product.

1. DIGITAL AUDIO OUT(OPTICAL)

Connects to an amplifier having a digital optical audio input jack.

2. DIGITAL AUDIO OUT(COAXIAL)

Connects to an amplifier having a digital coaxial audio input jack.

3. AV AUDIO OUT

Connects to the audio input of external equipment using audio cables.

4. AV VIDEO OUT(good video quality)

Connects the input of external equipment using a Video cable.

5. AV S-VIDEO OUT(better video quality)

Connects the input of external equipment using an S-Video cable.

Front Panel Display

6. COMPONENT VIDEO OUT(best video quality)

Connects to equipment having Component video input jacks.

7. AV 1 AUDIO IN

Connects the output of external equipment using an audio cables.

8. AV 1 VIDEO IN

Connects the output of external equipment using a video cable.

9. AV 1 S- VIDEO IN

Connects the output of external equipment using an S-Video cable.

10. In from aerial connector

11. Out to TV connector

■

The Antenna connection does not pass the

NOTE

output signal of the DVD. To watch DVD/HDD playback your TV, you must connect audio/video.

1. Lights when a disc is loaded.

2. Lights in the record mode.

3. Lights when a HDD/DVD is selected.

4. Lights when a -R/RW/RAM disc is loaded.

16 - English

5. Playing time/clock/current status indicator.

6. Lights in the progressive scan mode.

7. Lights to indicate the timer record mode.

Tour of the Remote Control

13. TITLE LIST/DISC MENU Button

Use this to enter the View Recording list/disc menu.

14. INFO Button

120 2 3

21 22 23

This will display current setting or disc status.

15. ANYKEY Button

Allows access to common functions of the recorder.

16. SUBTITLE Button

Press this to switch the DVD’s subtitle language.

17. REC Button

Use to make a recording on HDD/DVD-RW/-R discs.

5 6

7 8

24 6

8 25

27 28

18. REC PAUSE Button

Use this to pause during recording.

19. COPY Button

Press this when you copy DVD to HDD and HDD and vice-versa. To start copying, press the COPY button on the title list screen or press the COPY button during the playback.

20. INPUT SEL Button

Select input signal in external input mode ( AV2 or DV input)

21. HDD Button

Press this to operate HDD.

13 14

15 16 17 18 19

29 30

31 32

33 34 35

22. TV STANDBY/ON Button

23. OPEN/CLOSE Button

To open and close the disc tray.

24. CM SKIP Button

When a programme recorded on DVD disc or HDD is played, the unit can be set to automatically skip a portion of the programme.

25. PLAY/PAUSE Button

Press to play/pause a disc.

26. PROG Button

1. TV Button

Press this to operate TV.

2. DVD Button

Press this to operate DVD.

3. STANDBY/ON Button

4. NUMBER Buttons

5. TV/DVD Button (Not available)

6. REVERSE/FORWARD SKIP Buttons

Press to skip backwards or forwards.

7. REVERSE/FORWARD STEP Buttons

Each time this button is pressed, a new frame will appear.

8. REVERSE/FORWARD SEARCH Buttons

Press to search a disc backwards or forwards.

9. STOP Button

Press to stop a disc.

10. VOL Button

TV volume adjustment

11. MENU Button

Brings up the HDD & DVD RECORDER’s setup menu.

12. OK/DIRECTION Buttons (

…†œ √

Buttons)

Use this to select a TV programme.

27. TV MUTE/AUDIO Button

In TV mode, this operates as sound mute. Use this to access various audio functions on a disc (DVD mode).

28. RETURN Button

29. PLAY LIST/TITLE MENU Button

Use this to return to the Title menu, or to view the recorded files list.

30. CANCEL Button

31. REPEAT A-B Button

Allows you to repeat a title, chapter, track or disc.

32. REPEAT Button

Allows you to repeat a title, chapter, track or disc.

33. TIMER Button

Press to directly enter the Timer Recording Mode menu.

34. REC MODE Button

Use this to set the desired Recording time and picture

(XP/SP/LP/EP).

quality .

35. MARKER Button

Use this to bookmark a position while playing a disc.

PROG,

Getting Started

AV1,

English - 17

Connecting & Setting Up

This section involves var ious methods of connecting the HDD & DVD RECORDER to other external components and required initial setting modes.

Connecting & Setting Up

Quick Overview

A Quick Overview presented in this guide will give you enough information to start using the HDD & DVD RECORDER.

Connecting the HDD & DVD RECORDER

†

Other type of connecting the Video output cable

†

Other type of connecting the Audio output cable

†

Connecting to AV 1 IN, AV2 IN, DV input jack

Quick Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Connecting the HDD & DVD RECORDER . . . . . . . .19

Other type of connecting the Video output cable Other type of connecting the Audio output cable Connecting to AV 1 IN,AV 2 IN, DV input jack

18 - English

. . . . . .19

. . . . . . . .21

. . . . .23

Connecting the

Other type of connecting

HDD & DVD RECORDER

1. Disconnect the aerial cable from your TV and connect it to panel of the HDD & DVD RECORDER.

2. Connect Out to TV connector of the HDD & DVD RECORDER and the aerial input of your TV using the supplied aerial cable.

3. Use the Video/Audio Cable to connect ANALOG AUDIO OUT(R/L)/VIDEO OUT jacks on the HDD & DVD RECORDER to the Audio &Video jacks on the TV.

4. Plug in the HDD & DVD RECORDER and TV

5. Turn on the HDD & DVD RECORDER and TV.

6. Press the INPUT SEL. button on your TV remote

control until the Video signal from the HDD & DVD RECORDER appears on the TV screen.

Wall

In from aerial connector

on the rear

the Video output cable

There are several ways to output video signal. Select one of the following video connecting that best suits you below.

•

Case 1 : Connecting to a Video (Composite) output

•

Case 2 : Connecting to an S-Video output jack

•

Case 3 : Component Video output jacks

S-Video, Component video and Progressive Output Modes

•

S-Video and Component video output are available only if your TV supports S-Video input or Component video input, respectively. If S-Video or Component video output does not work, check the TV connections and the TV input selection settings.

•

Compared to standard interlaced video, progressive scan doubles the amount of video lines fed to your TV, resulting in a more stable, flickerfree, clear image than interlaced video. This is only available with TVs that suppor t progressive scan.

•

Progressive Scan Output (576p) Consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture, in case of 576 progressive scan picture problems, It is recommended that the user switch the connection to the ‘standard definition’output. If there are questions regarding our TV set compatibility with this model 576p HDD & DVD RECORDER, please contact our customer service centre.

jack

Connecting & Setting Up

NOTE

■

The RF cable connection of this product sends only signals of TV.You must connect Audio/Video cables to watch a DVD from your HDD & DVD RECORDER.

■

Power off HDD & DVD RECORDER, then you can watch programmes received through 2 RF cable.

English - 19

Case 1 : Connecting to a Video (Composite) output jack

Case 2 : Connecting to an S-Video output jack

1. Connect a video(yellow) cable between the VIDEO

(yellow) OUT jack on HDD & DVD RECORDER and VIDEO (yellow) INPUT jack on your TV (or AV amplifier).

•

You will enjoy high quality images.

2. Connect audio cables (white and red) between the AUDIO OUT jacks on HDD & DVD RECORDER and AUDIO IN jacks on TV (or AV amplifier).

(See pages 21~22)

20 - English

Case 3 : Component Video output jacks

Other type of connecting

1. Connect Component video cables(not supplied) between the COMPONENT OUT(Y,P

B,PR

) jacks on

HDD & DVD RECORDER and COMPONENT IN(Y,PB,PR) jacks on your TV.

•

You will enjoy high quality and accurate colour reproduction images.

2. Connect audio cables (white and red) between the AUDIO OUT jacks on the HDD & DVD RECORDER and AUDIO IN jacks on TV (or AV amplifier). (See pages 21~22).

3. After connecting, refer to the pages 37~39.

the Audio output cable

There are several ways to connect your HDD & DVD RECORDER. Select the audio connection that best suits you below.

•

Case 1 : Connecting to your TV

•

Case 2 : Connecting to a stereo amplifier with AV

•

Case 3 : Connecting to an AV amplifier with a

Manufactured under licence from Dolby Laboratories.“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

“DTS” and “DTS Digital Out” are trademarks of Digital Theatre System, Inc.

output jacks digital output jack

Connecting & Setting Up

NOTE

blue

red

green

blue

red

■

Make sure that the colour coded connections match.The Y, P

, P

component output jacks of your HDD & DVD RECORDER must be connected to the exact corresponding component input jacks on your TV.

■

Progressive setting is only available when the

HDD & DVD RECORDER

is connected to your TV using component cables. (See pages 37~39)

green

Case 1 : Connecting to your TV

If your TV has audio input jacks, use this connection.

white

red

yellow

white

red

yellow

English - 21

Case 2 : Connecting to a stereo amplifier with AV output jacks

Case 3: Connecting to an AV amplifier with a digital output jack

If your stereo amplifier only has AUDIO INPUT jacks(L and R), use the AUDIO OUT jacks.

whitered

Connecting & Setting Up

whitered

If your AV amplifier has a Dolby Digital, MPEG2 or DTS decoder and a digital input jack, use this connection.To enjoy Dolby Digital, MPEG2 or DTS sound, you will need to set up the audio settings. According to your amplifier, connect to an optical cable or a coaxial cable.(See pages 35~36)

Front(L) speaker

Front(R) speaker

Rear(L)

Front(L)

Rear(R)

Front(R)

Subwoofer Centre

22 - English

Connecting to AV 1 IN, AV 2 IN, DV input jack

This allows you to connect your HDD & DVD RECORDER to other external devices and view or record their outputs.

•

Case 1 : Connecting a VCR, Set-Top Box(STB) or

•

Case2 :

•

Case3 : Connecting a Camcorder to the DV IN jack

DVD player to the AV 1 IN jacks

Connecting a Camcorder to the AV 2 IN jacks

Case2 : Connecting a Camcorder to the AV 2 IN jacks

You can also use the AV 2 IN jacks on the front panel of the HDD & DVD RECORDER. You can record from connected equipment, such as a camcorder.

When an input source is inserted into AV 2 while viewing TV, the input will be switched to AV 2 automatically. If the input is not selected automatically, use INPUT SEL. button to select proper input.

Connecting & Setting Up

< DVD-HR730 / DVD-HR732 >

Case 1 : Connecting a VCR, Set-Top

Box(STB) or DVD player to the AV 1 IN jacks

Connecting a VCR or external device to AV1 IN jacks of the HDD & DVD RECORDER. You can record from connected equipment (VCR, STB or DVD).

VCR

STB

DVD

Camcorder

yellow

white

red

white

yellow

red

Case 3 : Connecting a Camcorder to the DV IN jack

If your digital camcorder has a DV output jack, connect it to the DV input jack of your HDD & DVD RECORDER.

< DVD-HR730 / DVD-HR732 >

Camcorder

NOTE

■

You can also use the AV 2 IN jacks on the front panel of the HDD & DVD RECORDER.

■

When the S-Video jack and Video jack are both connected, the S-Video jack will have priority.

■

Copy protected content cannot be recorded.

NOTE

■

If the input is not selected automatically, use INPUT SEL. button to select proper input.

English - 23

On-Screen Menu

System Setup

On-Screen Menu Navigation . . . . . . . . . . . . . . . . . . .24

Plug & Auto Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Presetting Channels with

the Auto Setup function . . . . . . . . . . . . . . . . . . . . . . .27

Navigation

The on-screen menus allow you to enable or disable various functions on your HDD & DVD RECORDER. Use the following buttons to open and navigate through the on-screen menus.

HDD & DVD RECORDER Library

HDD

Library

Title

Library

DivX (MPEG4)

Disc Manager

Music

Programme

Photo

Setup

MOVE SELECT RETURN EXIT

MENU Button

Press this button on the remote control to open the on-screen menu. Press again to exit the on-screen menu.

…†œ √ Buttons

Press these buttons on the remote control to move the selection bar …†œ √ to cycle through the menu options.

√√

Presetting Channels with

the Manual Setup function . . . . . . . . . . . . . . . . . . . . .28

Setting up the Language Options . . . . . . . . . . . . . . .29

Auto Power Off Setting . . . . . . . . . . . . . . . . . . . . . . . .30

Setting up the Quick Recording Options . . . . . . . . . .31

Automatic Chapter Creator . . . . . . . . . . . . . . . . . . . .32

DivX(R) Registration . . . . . . . . . . . . . . . . . . . . . . . . .33

CM Skip Time Setting . . . . . . . . . . . . . . . . . . . . . . . .33

EP Mode Time Setting . . . . . . . . . . . . . . . . . . . . . . . .34

Setting up the Audio Options . . . . . . . . . . . . . . . . . . .35

Setting up the Video display Options . . . . . . . . . . . . .37

Setting up the Progressive scan . . . . . . . . . . . . . . . .37

Canceling the Progressive scan . . . . . . . . . . . . . . . .38

Setting up the Parental Lock . . . . . . . . . . . . . . . . . . .39

24 - English

OK Button

Press this button on the remote control to confirm any new settings.

RETURN Button

Press this button on the remote control to return to the Previous menu screen displayed or to exit the on-screen menu.

Plug & Auto Setup

Auto channel scan will be started.

Your HDD & DVD RECORDER will automatically set itself up when it is plugged in for the first time.TV stations and clock will be stored in memory.The process takes a few minutes. Your HDD & DVD RECORDER will then be ready for use.

Connect the RF cable as indicated on page 19. (Connecting Your HDD & DVD RECORDER to the

TV Using the RF Cable and Audio/Video Cable.)

Plug the HDD & DVD RECORDER into the mains. “AUTO” in the front panel display flickers.

Press a number button to select the language.

Please wait.

•

The number of stations automatically stored by the HDD & DVD RECORDER depends on the number of stations that it has found.

Auto Channel Scan is completed. In 3~4 seconds, you will see Clock Setting Menu.If you want to

start Clock Setting immediately, Press OK button.

Auto Setup

68%

Auto channel scan completed successfully.

System Setup

Press 1 for English

Touche 2 pour Français

Drücken Sie 3 Für Deutsch

Pulse 4 para Español

Premere 5 per Italiano

Druk op 6 voor Nederlands

з‡КПЛЪВ 7 ‰Оﬂ ЫТТНУ„У ﬂБ.

Press the OK button to start the auto setup.

Auto setup will be started.

Yes No

Check the date and time.

mo. da. yr. hr. min.

JAN 01 2006 12 00

Sunday

•if it is :Correct, press OK button then the date and time will be saved.If you don't press the OK button, the date and time will be saved automatically after 5 seconds.

• if it is : Incorrect, input correct Month, Day,Year,

Hour or Minute using number buttons. Press OK button then the date and time will be saved.When you need to change clock setting, you can set up it manually.

…†œ √ buttons or

English - 25

NOTE

■

Now, HDD & DVD RECORDER is ready for use.Function for “Plug & Auto Setup” is fixed already. So if you want to change this fixed one, you can change it by Presetting the Stations in OSD “Presetting Channels with the Manual Setup function” menu. (See pages 28~29)

■

Auto setup function can be performed by pressing STOP ( ) on the unit

continuously for 5 seconds or more during power off with no disc inserted.

Setting the Clock

This menu is used to set the current time. You need to set the time to use timer recording.

With the unit in Stop mode, press the MENU button

HDD & DVD RECORDER Library

HDD

Library

Title

Library

DivX (MPEG4)

Disc Manager

Music

Programme

Photo

Setup

MOVE SELECT RETURN EXIT

√√

System Setup

Press the …† buttons to select Setup, then press the OK or √ button.

HDD & DVD RECORDER Setup

HDD

Disc Manager

System

Library

PVR Option Language

Programme

Audio

Setup

Video Parental Lock

MOVE SELECT RETURN EXIT

√√

Press the …†buttons to select System, then press the OK or √ button.

HDD & DVD RECORDER System

HDD

Disc Manager

Channel Set

Library

Clock Set Auto Power Off : Off

Programme

Quick Recording : Off

Setup

Chapter Creator : Off DivX(R) Registration

MOVE SELECT RETURN EXIT

√√

26 - English

Press the …† buttons to select Clock Set, then press the OK or √ button.

Press the …†œ √ buttons to input Month, Day, Year, Hour or Minute.Press the number buttons to input clock data directly. The day of the week is displayed automatically.

HDD & DVD RECORDER Clock Set

HDD

Library

Disc Manager

mo. da. yr. hr. min.

Programme

JAN 01 2006 12 00

Setup

Sunday

MOVE SELECT RETURN EXIT

Press the OK button, then the date and time will be saved.If you don’t press the OK button, it will

not be saved.

Presetting Channels with the Auto Setup function

This feature allows you to manually set the HDD & DVD RECORDER tuner band to Antenna or Cable, whichever you connected to the Antenna In jack dur ing initial setup.

With the unit in Stop mode, press the MENU button

Press the …† buttons to select Setup, then press the OK or √ button.

HDD & DVD RECORDER Setup

HDD

Disc Manager

System

Library

PVR Option Language

Programme

Audio

Setup

Video Parental Lock

MOVE SELECT RETURN EXIT

√√

System Setup

press the …†buttons to select System, then press the OK or √ button.

HDD & DVD RECORDER System

HDD

Disc Manager

Channel Set

Library

Clock Set Auto Power Off : Off

Programme

Quick Recording : Off

Setup

Chapter Creator : Off DivX(R) Registration

MOVE SELECT RETURN EXIT

Press the …† buttons to select Channel Set, then press the OK or √ button.

HDD & DVD RECORDER Channel Set

HDD

Disc Manager

Auto Setup

Library

Manual Setup

Programme

Setup

MOVE SELECT RETURN EXIT

√√

English - 27

Press the …† buttons to select Auto Setup, then

press the OK or √ button. The message “Your data will be lost. Press [OK] to continue, [Return] to exit.” is displayed.

HDD & DVD RECORDER Channel Set

HDD

Disc Manager

Auto Setup

Library

Manual Setup

Your data will be lost.

Programme

Press [OK] to continue, [Return] to exit.

Setup

√√

Presetting Channels with the Manual Setup function

You can add preset channel that Auto Channel Search missed. And you can delete a channel you wish to remove. You can programme the order of channels.

Press the OK button.If you want to exit, press the

MENU button.

System Setup

• The first frequency band is scanned and the first station found is displayed and stored.And the HDD & DVD RECORDER searches for the second station and so on.

• The number of stations automatically stored by the HDD & DVD RECORDER depends on the number of stations that it has found.

Please wait.

SELECT RETURN EXIT

Auto Setup

Stop

With the unit in Stop mode, press the MENU

button.

Press the …†buttons to select Setup, then press

the OK or √ button.

HDD & DVD RECORDER Setup

HDD

Disc Manager

System

Library

PVR Option Language

Programme

Audio

Setup

Video Parental Lock

MOVE SELECT RETURN EXIT

√√

Press the …†buttons to select System,

then press the OK or √ button.

HDD & DVD RECORDER System

HDD

Library

Disc Manager

Programme

Setup

Channel Set

Channel Set Clock Set Auto Power Off : Off Quick Recording : Off Chapter Creator : Off DivX(R) Registration

√√

Channel scan will be started. Press the OK button to stop the Auto Setup.

28 - English

MOVE SELECT RETURN EXIT

Press the …†buttons to select Channel Set,

then press the OK or √ button.

HDD & DVD RECORDER Channel Set

HDD

Disc Manager

Auto Setup

Library

Manual Setup

Programme

Setup

MOVE SELECT RETURN EXIT

√√

Press the …†buttons to select Manual Setup, then press the OK or √ button.

Manual Setup

PR CH Name

01 002 - - - -

01 - - - - - - - 02 004 - - - 03 - - - - - - 04 - - - - - - 05 - - - - - - 06 - - - - - - 07 - - - - - - -

MOVE SELECT RETURN EXIT

Press the …† buttons to select a PR(programme) you wish to edit, delete, or swap, then press the

ANYKEY button. Select Edit, Delete or Swap.

Manual Setup

PR CH Name

01 - - - - - - -

01 002 - - - 02 004 - - - 03 - - - - - - 04 - - - - - - 05 - - - - - - -

Edit

06 - - - - - - -

Delete

07 - - - - - - -

Swap

MOVE SELECT RETURN EXIT

- CH :Tune the channel using œ √ buttons.

- Name :Display station name automatically detected in broadcasting signal.If not detected, you can edit name by using …†œ √ buttons.

- MFT(Manual Frequency Tunning) :You can tune up the

channel frequency better using œ √ buttons.

• In case of Delete : the channel information of selected

PR(programme) will be removed.

• In case of Swap :You can swap the channel

information of two PR(programme).For example, if you wish to swap PR2 and PR5, select swap at PR2, then press the OK button at PR5.

System Setup

Setting up the Language

• In case of Edit :You can add or edit PR(programme) information.After change PR informations(CH., Name, MFT), select

Save, then press the OK button.

Manual Setup

PR 01 CH 002

Name - - - MFT

Save

MOVE CHANGE

Options

If you set the audio, subtitle, disc menu and on-screen menu, in advance, they will come up automatically every time you watch a movie. If the selected language is not recorded on the disc, the original pre-recorded language is selected.

With the unit in Stop mode, press the MENU button.

English - 29

Press the …† buttons to select Setup, then press the OK or √ button.

HDD & DVD RECORDER Setup

HDD

System

Library

Disc Manager

PVR Option Language

Programme

Audio

Setup

Video Parental Lock

MOVE SELECT RETURN EXIT

Press the …†buttons to select the desired

language, then press the OK or √ button.

√√

NOTE

■

Press the RETURN or œ button to return to the previous menu.Press the MENU button to exit the menu.

■

The selected language will only appear if it is supported on the disc.

Press the …†buttons to select Language, then press the OK or √ button.

Language setup menu will be displayed.

System Setup

Press the …†buttons to select the desired language option, press the OK or √ button.

HDD & DVD RECORDER Language

HDD

Disc Manager

HDD & DVD RECORDER Language

HDD

Disc Manager

Audio :Original

Audio : Original

Library

Subtitle : Automatic Disc Menu :English

Programme

Menu : English

Setup

MOVE SELECT RETURN EXIT

Audio :Original

Audio : Original

Library

Subtitle : Automatic Disc Menu :English

Programme

Menu : English

Setup

MOVE SELECT RETURN EXIT

Original

English

Français Deutsch Español Italiano Nederlands Korean

Auto Power Off Setting

√√

This feature automatically turns off your HDD & DV D RECORDER, if you do not press any button for the selected time.

With the unit in Stop mode, press the MENU

button.

Press the …† buttons to select Setup, then press

the OK or √ button.

HDD & DVD RECORDER Setup

HDD

Disc Manager

System

Library

PVR Option Language

Programme

Audio

Setup

Video Parental Lock

MOVE SELECT RETURN EXIT

√√

• Audio : For the disc audio language.

• Subtitle : For the disc subtitles.

• Disc Menu: For the disc menu contained on the

disc

• Menu:

For the on-screen menu of your HDD & DVD RECORDER.

30 - English

Press the …† buttons to select System,

then press the OK or √ button. System menu will be displayed.

HDD & DVD RECORDER System

HDD

Disc Manager

Channel Set

Library

Clock Set Auto Power Off : Off

Programme

Quick Recording : Off

Setup

Chapter Creator : Off DivX(R) Registration

MOVE SELECT RETURN EXIT

√√

+ 216 hidden pages