Samsung DVD-HR720 User Manual [nl]

Instruction Manual

DVD-HR720

English

Nederlands

www.samsung.com

AK68-00819W-00

Warning

IMPORTANT NOTE

The mains lead on this equipment is supplied with a
moulded plug incorporating a fuse. The value of the
fuse is indicated on the pin face of the plug. If it requires
replacing, a fuse approved to BS1362 of the same
rating must be used.

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE THE COVER(OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.

Getting Started

This symbol indicates “dangerous voltage”
inside the product that presents a risk of
electric shock or personal injury.

This symbol indicates important instructions
accompanying the product.

Do not install this equipment in a confined space such
as a bookcase or similar unit.

WARNING :

CAUTION : HDD & DVD RECORDER USES AN INVISIBLE

CAUTION

THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR
YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.

To prevent damage which may result in fire
or electric shock hazard, do not expose this
appliance to rain or moisture.

LASER BEAM WHICH CAN CAUSE
HAZARDOUS RADIATION EXPOSURE IF
DIRECTED. BE SURE TO OPERATE
RECORDER CORRECTLYAS INSTRUCTED.

Never use the plug with the fuse cover omitted if the cover
is detachable. If a replacement fuse cover is
required, it must be of the same colour as the pin face of
the plug. Replacement covers are available from your
dealer.

If the fitted plug is not suitable for the power points in your
house or the cable is not long enough to reach a
power point, you should obtain a suitable safety approved
extension lead or consult your dealer for assistance.

However, if there is no alternative to cutting off the plug,
remove the fuse and then safely dispose of the
plug. Do not connect the plug to a mains jack, as there is
a risk of shock hazard from the bared flexible cord.

The product unit accompanying this user manual is
licenced under certain intellectual property rights of certain
third parties. This licence is limited to private non­commercial use by end-user consumers for licenced
contents.
No rights are granted for commercial use.
The licence does not cover any product unit other than this
product unit and the licence does not extend to any
unlicenced product unit or process conforming to ISO/IEC
11172-3 or ISO/IEC 13818-3 used or sold in combination
with this product unit. The licence only covers the use of
this product unit to encode and/or decode audio files
conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3.
No rights are granted under this licence for product
features or functions that do not conform to the ISO/IEC
11172-3 or ISO/IEC 13818-3.

2- English

Handling Cautions

Precaution

Important Safety Instructions

Read these operating instructions carefully before using
the unit. Follow all the safety instructions listed below.
Keep these operating instructions handy for future
reference.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings, Install in
accordance with the manufacturer's instructions.

8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or
grounding- type plug. Apolarized plug has two
blades with one wider than the other. Agrounding­type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. if the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.

10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, the point where they exit from the
apparatus.

11 ) Only use attachments/accessories specified by the

manufacturer.

12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.

13) Unplug this apparatus during lightning storms or
when unused for long periods of time.

14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.

• Before connecting other components to this
recorder, be sure to turn them all off.

• Do not move the recorder while a disc is being
played, or the disc may be scratched or broken, the
recorder’s internal parts may be damaged.

• Do not put a flower vase filled with water or any
small metal objects on the recorder.

• Be careful not to put your hand into the disc tray.

• Do not place anything other than the disc in the

disc tray.

• Exterior interference such as lightning and static
electricity can affect normal operation of this
recorder. If this occurs, turn the recorder off and on
again with the
disconnect and then reconnect the AC power cord
to the AC power outlet. The recorder will operate
normally.

• Be sure to remove the disc and turn off the
recorder after use.

• Disconnect the AC power cord from the AC outlet
when you don’t intend to use the recorder for long
periods of time.

• Clean the disc by wiping in a straight line from the
inside to the outside of the disc.

DVD STANDBY/ON button, or

Maintenance of Cabinet

For safety reasons, be sure to disconnect the AC
power cord from the AC outlet.

•

Do not use benzene, thinner, or other solvents
for cleaning.

•

Wipe the cabinet with a soft cloth.

HDD (Hard Disk Drive)

The hard disk has a high storage density, which
enables long recording durations and quick
access to written data. However, it can easily be
damaged by shock, vibration or dust and should
be kept away from magnets. To avioid losing
important data, observe the following precautions.

• Do not use the HDD & DVD RECORDER in a
place subject to extreame changes in
temperature.

• Do not apply a strong shock to the HDD & DVD
RECORDER.

• Do not place the HDD & DVD RECORDER in a
location subject to mechanical vibrations or in an
unstable location.

• Do not place the HDD & DVD RECORDER on
top of a heat source.

Getting Started

English - 3

• Do not disconnect the AC power cord while the
power is on.

• Do not attempt to change the hard disk. This
may result in a malfunction.

Should the hard disk be damaged, you cannot
recover lost data. The hard disk is only a
temporary storage space.

Getting Started

Disc Handling

• Use discs with regular
shapes. If an irregular disc
(a disc with a special shape)
is used, this HDD & DVD
RECORDER may be
damaged.

Holding discs

• Avoid touching the surface of a
disc where recording is
performed.

• Do not use discs printed with label printers
available on the market.

• Do not load warped or cracked discs.

Disc Storage

Be careful not to harm the disc because the data on
these discs is highly vulnerable to the environment.

• Do not keep under direct sunlight.

• Keep in a cool ventilated area.

• Store vertically.

• Keep in a clean protection jacket.

• If you move your HDD & DVD RECORDER suddenly

from a cold place to a warm place, condensation may
generate on the operating parts and lens and cause
abnormal disc playback. If this occurs, remove the
disc and wait for one to two hours with the power on
before atttempting playback.

• Be careful not to harm the disc because the data on
these discs is highly vulnerable to the environment.

Disc Specifications

DVD-RAM, DVD-RW and DVD-R

• Clean with an optional DVD-RAM/PD
disc cleaner (LF-K200DCA1 where
available). Do not use cleaners or
cloths for CDs to clean DVD-RAM/

-RW/-R discs.

DVD-Video, Audio-CD

• Wipe off dirt or contamination on the disc with a
soft cloth.

Cautions on handling discs

• Do not write on the printed side with a ball-point
pen or pencil.

• Do not use record cleaning sprays or antistatic.
Also, do not use volatile chemicals, such as
benzene or thinner.

• Do not apply labels or stickers to discs. (Do not
use discs fixed with exposed tape adhesive or
leftover peeled-off stickers.)

• Do not use scratch-proof protectors or covers.

Disc Type

DVD-Video

• A digital versatile disc (DVD) can contain up to 135­minutes of images, 8 audio languages and 32 subtitle
languages. It is equipped with MPEG-2 picture
compression and Dolby digital surrounding, allowing
you to enjoy vivid and clear theatre quality images in
the comfort of your own home.

• When switching from the first layer to the second layer
of a dual-layered DVD Video disc, there may be
momentary distortion in the image and sound. This is
not a malfunction of the unit.

• Once a DVD-RW/-R recorded in Video Mode is
finalised, it becomes DVD-Video.

4- English

Audio CD

DVD-RW Disc Playback and Recording

• An audio disc on which 44.1kHz PCM Audio is
recorded.

• Plays CD-DA format audio CD-R and CD-RW discs.

• The unit may not be able to play some CD-R or CD-

RW discs due to the condition of the recording.

CD-RW/-R

• Use a 700MB(80 minutes) CD-R/RW disc. If possible,
do not use a 800MB(90 minutes) or above disc, as the
disc may not play back.

• If the CD-R/RW disc was not recorded as a closed
session, you may experience a delay in the early
playback time, all recorded files may not play.

• Some CD-R/RW discs may not be playable with this
unit, depending on the device which was used to burn
them. For contents recorded on CD-R/RW media from
CDs for your personal use, playability may vary

depending on contents and discs.

DVD-R Disc Playback and Recording

• Once a DVD-R recorded in Video Mode is finalised, it
becomes DVD-Video.

• You can record onto the available space on the disc
and perform editing functions such as giving titles to
discs and programmes and erasing programmes
before finalising.

• When programming is erased from a DVD-R, that
space does not become available. Once an area on a
DVD-R is recorded on, that area is no longer available
for recording, whether the recording is erased or not.

• It takes about 30 seconds for the unit to complete
recording management information after recording
finishes.

• This product optimizes the DVD-R for each recording.
Optimizing is carried out when you start recording
after inserting the disc or turning on the unit.
Recording onto the disc may become impossible if
optimizing is carried out too many times.

• Playback may be impossible in some cases due to the
condition of recording.

• This unit can play back DVD-R discs recorded and
finalised with a Samsung DVD video recorder. It may
not be able to play some DVD-R discs depending on
the disc and the condition of the recording.

• Recording and playback can be performed on DVD­RW discs in both the Video and VR Modes.

• Once a DVD-RW recorded in both the Video and VR
Modes is finalised, you cannot perform addtional
recording.

• Once a DVD-RW recorded in Video Mode is finalised,
it becomes DVD-Video.

• In both modes, playback can be performed before and
after finalisation, but additional recording, deleting and
editing can not be performed after finalisation.

• If you want to record the disc in VR Mode and then
record in V Mode, be sure to execute Format. Be
careful when executing Format because all the
recorded data may be lost.

• A DVD-RW blank disc is initialized to VR Mode when
first initialized.

DVD-RAM Disc Playback and Recording

• Ensure that the recording mode is set to VR mode.
Otherwise, this product will not be able to play the
recording.

• You cannot play a DVD-RAM in most DVD
components due to compatibility issues.

• Only DVD-RAM standard Version 2.0. discs can be
played in this unit.

• DVD-RAM recorded on this unit may not work with
other DVD components. To determine compatibility
with these DVD-RAM discs, refer to the user’s manual
for the player.

• For cartridge type DVD-RAM discs, remove the
cartridge and use the disc only.

Disc Copy

Contents Copy Specifications

Contents HDD
Recorded Video Title Supported Supported
Copy Protected Title Not supported Not supported

Copy Once

MP3 Not supported supported
JPEG(photo) Not supported supported
DivX Not supported Not supported

Title

➞ DVD DVD ➞

Move

(Deletes the Title in the

HDD after copying)

Not supported

HDD

Getting Started

Once "Copy Once programme" has been recorded on the
DVD disc, this title cannot be copied to HDD anymore.
But "Copy Once programme" has been recorded on the
HDD, this title can be copied to DVD-RW(VR mode) or
DVD-RAM.

English - 5

COPY PROTECTION

Using JPEG disc

• Many DVD discs are encoded with copy
protection. Because of this, you should only
connect your HDD & DVD RECORDER directly to
your TV, not to a VCR. Connecting to a VCR
results in a distorted picture from copy-protected
DVD discs.

• This product incorporates copyright protection
technology that is protected by methods claims of
certain U.S. patents and other intellectual

Getting Started

property rights owned by Macrovision Corporation
and other rights owners. Use of this copyright
protection technology must be authorised by
Macrovision Corporation, is intended for home
and other limited viewing uses only unless
otherwise authorised by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.

Protection

This HDD & DVD RECORDER can allow you to protect
the contents of your discs, as described below.

• Programme-protected: See page 93
“Locking(Protecting) a Title”

• Disc-protected: See page 118 “Disc Protection”

❋

DVD-RAM/-RW/-R discs that are incompatible with
the DVD-VIDEO format cannot be played with this
product.

❋

For more information on DVD recording compatibility,
consult your DVD-RAM/-RW/-R manufacturer.

❋

Use of poor quality DVD-RAM/-RW/-R discs may
cause following unexpected problems including,
without limitation, recording failure, loss of recorded
or edited materials or damage to the recorder.

• CD-R, DVD-R/RW/RAM, HDD with JPEG files
recorded with UDF, ISO9660 or JOLIET format can be
playbacked.

• Only JPEG files with the “.jpg” or “.JPG” extension
can be displayed.

• The unit can handle a maximum of 4,500 files and
1,000 sub folders under a folder.

• MOTION JPEG and progressive JPEG are not
supported.

Using MPEG4 disc

• Disc : CD-RW/-R, DVD-RAM/-RW/-R

• MPEG4 File with following extensions can be played. :

.avi, .divx, .AVI, .DIVX

• MPEG4 Codec format : DivX 3.11 DivX 4.x DivX 5.x
DivX-Pro (without QPEL and GMC)

• Available Audio Format : “MP3”, “MPEG”, “WMA”,
“LPCM”, “AC3”

• Supported subtitle file formats: .smi, .srt, .sub, .psb,

.txt, .ass

DVD-RW (VR mode)

• This is a format that is used for recording data on a
DVD-RAM or DVD-RW disc. You can record multiple
titles, edit, delete, partial delete, create a playlist, etc.

• A disc that is recorded in this mode may not be
played by existing HDD & DVD RECORDER.

Disc Format

Using MP3 disc

• CD-R, DVD-R/RW/RAM, HDD with MP3 files recorded
with UDF, ISO9660 or JOLIET format can be
playbacked.

• Only MP3 files with the “.mp3” or “.MP3” extension
can be played.

• For MP3 files recorded with a VBR(Variable Bit
Rates), from 32 Kbps to 320 Kbps, the sound may cut
in out.

• Playable bit-rate range is from 56 Kbps to 320 Kbps.

• The unit can handle a maximum of 1,500 files and

1,000 sub folders under a folder

6- English

DVD-RW (V mode)

• This is a format that is used for recording data on a
DVD-RW or DVD-R disc. The disc can be played by
existing HDD & DVD RECORDER once it has been
finalised.

• If a disc that has been recorded in Video Mode by a
different maker’s recorder but has not been finalised,
it cannot be played or additionally be recorded by this
recorder.

Do not use the following discs!

• LD, CD-G, CD-I, CD-ROM, DVD-ROM, DVD+R and
DVD+RW discs should not be used in this product.
[Note]
Disc types that can be played : CD/CD-RW/-RW/
MP3/JPEG/DVD-Video/DVD-RAM/-RW/-R.
For a DVD-RW/-R disc, which has been recorded in
Video Mode on another component, it can play only
when finalised.

• Some commercial discs and DVD discs purchased
outside your region may not be playable with this
product. When these discs are played, either “No
disc.” or “Please check the regional code of the disc.”
will be displayed.

• If your DVD-RW disc is an illegal copy or is not in
DVD video format, it may also not be playable.

❋We recommend using one of the discs in the table

as they have been confirmed to be compatible
with this unit. Other discs may not perform
correctly.

Media Disc SPEED

TDK 4x
Beall 4x

DVD-R That’s4x

Maxell 4x
Panasonic 4x
TDK 2x
Maxell 2x

DVD-RW Optodisc 2x

Radius 2x
Verbatim 2x
Maxell 3x

DVD-RAM

Fujifilm 3x
TDK 2x

Panasonic 3x

Getting Started

Disc Maximum no. of recordings by disc type
DVD-RAM 100,000
DVD-RW 1,000
DVD-R 1

• We take no responsibility and offer no compensation
for any recording failure, loss of recorded or edited
material and/or damage to the recorder arising from
usage of unrecommended discs.

English - 7

Contents

Getting Started

Getting Started

Case2 : Connecting a Camcorder to

the AV 2 IN jacks . . . . . . . . . . . . . . . . . . . . . . . . . .23

Case3 : Connecting a Camcorder to

the DV IN jack . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

System Setup

System Setup

Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Getting Started

Precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . .3

Handling Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Maintenance of Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . .3

HDD (Hard Disk Drive) . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Disc Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Disc Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Disc Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Disc Copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

General Features . . . . . . . . . . . . . . . . . . . . . . . . . .10

Before Reading the User’s Manual . . . . . . . . . . . . .11

How to use the HDD & DVD RECORDER . . . . . . .11

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Front Panel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Tour of the Remote Control . . . . . . . . . . . . . . . . . . . . . .17

Connecting & Setting Up

Connecting & Setting Up

On-Screen Menu Navigation.....................................24

Plug & Auto Setup......................................................25

Setting the Clock........................................................26

Presetting Channels with the Auto Setup function...27
Presetting Channels with the Manual Setup

function .......................................................................28

Setting up the Language Options.............................29

Auto Power Off Setting..............................................30

CM Skip Time Setting................................................31

EP Mode Time Setting...............................................32

Setting up the Front Display Options........................33

Automatic Chapter Creator........................................34

Setting up NICAM Options........................................35

DivX(R) Registration..................................................36

Setting up the Audio Options.....................................37

Setting up the Video display Options........................38

Setting up the Progressive scan...............................40

Canceling the Progressive scan...............................41

Setting up the Parental Control.................................42

If you forgot your password............................................42

About the Rating Level ...................................................43

About the Change Password.........................................43

Quick Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Connecting the HDD & DVD RECORDER . . . . . .19

Other type of connecting the Video output cable

Case 1 : Connecting to a Video (Composite)

output jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Case 2 : Connecting to an S-Video output jack . . . . .20

Case 3 : Component Video output jacks . . . . . . . . . .21

Other type of connecting the Audio output cable .21

Case 1 : Connecting to your TV . . . . . . . . . . . . . . . . .21

Case 2 : Connecting to a stereo amplifier

with AV output jacks . . . . . . . . . . . . . . . . . . . . . . . . .22

Case 3: Connecting to an AV amplifier

with a digital output jack . . . . . . . . . . . . . . . . . . . . . .22

Connecting AV 1 IN, AV 2 IN, DV input jack . . . . .23

Case 1 : Connecting a VCR, Set-Top Box(STB)

or DVD player to the AV 1 IN jacks . . . . . . . . . . . .23

. . .19

8- English

Playback

Playback

Before Playing............................................................44

Playing a Disc.............................................................45

Using the Disc Menu & Title Menu...........................46

Using the Search & Skip Functions..........................46

Slow Motion Play/Step Motion Play..........................47

About ANYKEY..........................................................48

Playing the Title List...................................................50

Navigation Menu........................................................51

Using the Markers......................................................54

Using the Bookmarks ................................................56

Selecting the Subtitle Language...............................58

Selecting the Soundtracks & Audio Channels.........59

Changing the Camera Angle.....................................60

Repeat Play................................................................60

Zooming-In .................................................................62

Select Media...............................................................63

Playing an Audio CD/MP3.........................................63

Playing a Picture........................................................70

Playing an MPEG4....................................................73

Recording

Recording

Before Recording.......................................................75

Recording the current TV programme you are

watching......................................................................77

Recording from external equipment

you are watching........................................................79

Copying from a Camcorder.......................................80

Making an One Touch Recording (OTR).................81

Chasing Play..............................................................82

Simultaneous Recording and Playback ...................83

Making a Timer Recording .......................................84

Flexible Recording (for Timer recording only)..........86

Editing the Timer Record List....................................86

Deleting a Timer Record List.....................................87

Go To History List.......................................................88

Copying from DVD to HDD.....................................114

Copying MP3 or JPEG Files

from a Disc to HDD ................................................115

File Copy........................................................................115

Folder Copy ...................................................................116

Disc Manager...........................................................117

Editing the Disc Name ..................................................117

Disc Protection...............................................................118

Formatting a Disc ..........................................................119

Delete All Title Lists/Music Lists/Photo Lists................120

Delete All Title Lists ......................................................121

Finalising a Disc ...........................................................122

Unfinalising a Disc (V/VR mode) .................................123

Reference

Reference

Troubleshooting........................................................124

Specifications ...........................................................128

Getting Started

Editing

Editing

Basic Editing (Title List).............................................92

Renaming(Labeling) a Title.............................................92

Locking (Protecting) a Title ............................................93

Deleting a Title.................................................................94

Splitting a Section of a Title (Split)..................................95

Deleting a Section of a Title (Partial Delete)..................97

Advanced Editing (Playlist) .......................................99

Creating a Playlist............................................................99

Playing Entries in the Playlist .......................................100

Renaming a Playlist Entry ............................................101

Editing a Scene for the Playlist.....................................102

Deleting a Playlist Entry from the Playlist....................106

Copying from HDD to DVD.....................................107

About the Copy Screen ................................................107

Changing the Record Mode .........................................110

Copying Multiple Titles at One Time.......................110

Deleting an Undesired Title from the Copy List...........112

Previewing a Selected Title from the Copy List...........112

Selecting Record Mode of Each Title

from the Copy List.........................................................113

Changing Record Mode of All Titles

from the Copy List.........................................................113

English - 9

General Features

Automated Quality Adjustment for Timer
Recording

If FR mode is selected, the video quality is adjusted
automatically so that all video for the scheduled time can
be recorded onto the free disc space.
(See page 86)

The HDD & DVD RECORDER allows you to record and
play high quality digital video on DVD-RAM/-RW/-R or
HDD discs. You can also edit digital images on
DVD-RAM/-RW/-R discs or HDD.

Getting Started

HDD Recording

You can record up to 127 hours of video (in EP mode) on
the internal 80GB (gigabyte) hard disk (HDD).
With both recordable DVD and a high-capacity HDD in the
same recorder, you have the flexibility to keep recordings
on the HDD for quick access anytime, or record to DVD
for archiving or playing on other DVD players.

Copy between HDD and DVD

You can copy recordings from the HDD to recordable
DVD, or from DVD to the HDD. Usually you can use the
high speed copy feature.
You can also choose to copy material at different
recording quality from the original. For example, you might
want to copy a XP mode (highest quality) recording on the
HDD to SP (standard play) quality on a DVD so that you
can fit other recordings on the same disc.

Simultaneous Recording and Playback

Playback and recording for both DVDs and the built-in
hard disk drive (HDD) are completely independent. For
example you can record a broadcast programme to either
a recordable DVD or the HDD, while watching another
recording you already made on the same DVD or on the
HDD.

High quality digital audio and video recording
and playback

Record up to 16-hours of video with a double sided 9.4
GB DVD-RAM disc, up to 8-hours of images with a 4.7
GB DVD-RAM/-RW/-R disc, depending on the recording
mode.

Creating a DVD video title using DVD-RW/-R
disc

With the HDD & DVD RECORDER, you can create your
own DVD Video titles on 4.7 GB DVD-RW/-R discs.

Copying data from a digital camcorder using
a DV input jack

Record DV Device video onto HDD and DVD-RAM/-RW/-R
discs using the DV input jack (IEEE 1394-4pin/4pin).
(See page 80)

High quality progressive scan

Progressive scanning provides high resolution and flicker
free video. The 10-bit 54-MHz DAC and 2D Y/C
Separating Circuitry provides the highest image playback
and recording quality. (See pages 40~41)

A variety of functions with an easy-to-use
user interface

The integrated menu system and the messaging
function allow you to perform desired operations both
easily and conveniently. With a
DVD-RW disc, you can edit recorded video, create a
playlist, edit video in a specific sequence according to
your requirements.

HDD,

DVD-RAM or

MPEG4 playback

This HDD & DVD RECORDER can play MPEG4 formats
within an avi file.

DivX Certification

DivX, DivX Certified, and associated
logos are trademarks of DivXNetworks,
Inc and are used under licence.

Selectable Recording Mode

You can set your recorder to one of four different
recording speeds, each varying in recording quality and
length. EP (6Hr or 8Hr) mode yields the most recording
time, LP & SP modes provide less recording time with
higher quality recording, XP mode gives you the highest
quality recording.

10 - English

Copyright

Before Reading the
User’s Manual

Make sure to check the following terms before reading
the user manual.

Icons that will be used in manual

Icon Term Definition

HDD This involves a function available

in HDD.
This involves a function available

DVD

RAM

RW

CD

JPEG in CD-R/-RW or DVD-R/-RW/

MP3

MPEG4 in CD-R/-RW or DVD-R/-RW/

Caution function does not operate or

NOTE on the page that help each

One-Touch

button by using only one button.

ANYKEY A function that can be operated

button by using

About the use of this user’s manual

1) Be sure to be familiar with Safety Instructions before
using this product. (See pages 2~7)

2) If a problem occurs, check the Troubleshooting.
(See pages 124~127)

in DVD or DVD-R/DVD-RW
discs that have been recorded
and finalised in Video Mode.

This involves a function available
in DVD-RAM.

This involves a function available
in DVD-RW.

This involves a function available

R

in DVD-R.
This involves a function available

in a data CD (CD-R or CD-RW).
This involves a function available

-RAM discs.
This involves a function available

in CD-R/-RW or DVD-R/-RW/

-RAM discs.
This involves a function available

-RAM discs.
This involves a case where a

settings may be cancelled.
This involves tips or instructions

function operate.
A function that can be operated

ANYKEY button.

©2005 Samsung Electronics Co.
All rights reserved; No part or whole of this user’s
manual may be reproduced or copied without the prior
written permission of Samsung Electronics Co.

How to use the
HDD & DVD RECORDER

Step 1

This unit can record on the following types of discs.
If you want to repeatedly record on the same disc
or you want to edit the disc after recording, select a
rewritable DVD-RW or DVD-RAM type disc. If you
want to save a recording without any changes,
choose a non-rewritable DVD-R. You can record
files directly to the built-in HDD or edit a recorded
file.

Step 2

Unlike a VCR, the recorder automatically starts
formatting when an unused disc is inserted. This is
required for the preparation of recording on a disc.

Using a HDD

Formatting unneccessory.

Using a DVD-RAM

This type of disc can be formatted in DVD-Video
Recording format (VR mode). You can edit
recorded image and create a playlist and edit
images in a specific sequence according to your
requirements.

Using a DVD-RW

This type of disc can be formatted in either DVD­Video format (V mode) or DVD-Video Recording
format (VR mode). For an unused disc, a message
that asks whether to format in VR Mode or not is
displayed. You can play a Video mode disc on
various DVD components. AVR mode disc allows
more varied editing.

Using a DVD-R

This type of disc can be formatted in DVD Video
format. After formatting is complete, you can record
on the disc. You can play this type of discs on
various DVD components only when they have
been finalised.

Select the disc type or HDD

Format the disc to start recording

Getting Started

English - 11

■

You can only use either the VR or Video

NOTE

mode on a DVD-RW, but not both at the
same time.

■

You can change the DVD-RW format to
another format by reinitializing. It should
be noted that the disc's data will be lost
when changing formats.

Getting Started

Step 3

There are two different recording methods, Direct
Recording and Timer Recording. Timer recording is
classified.

Recording mode : XP (high quality mode), SP
(standard quality mode), LP (long recording mode),
and EP (extended mode) according to the
recording mode. When recording is set in the FR
mode, the best quality picture is recorded with
regards to the remaining time on the disc.

Recording

Step 5

Editing on discs is easier than conventional video
tapes. The recorder supports many different edit
functions, possible only with DVDs and HDD.

With a simple and easy edit menu, you can operate
various edit functions, such as delete, copy, rename,
lock, etc., on a recorded title.

Creating a playlist (DVD-RAM/-RW in VR mode,
HDD)

With this recorder, you can create a new playlist on
the same disc and edit it without the change of the
original recording.

Step 6

Editing a recorded disc

Finalising & Playing on
other DVD components

Step 4

You can select the title you want to play in a
displayed menu and then immediately start
playback.

A DVD consists of sections, called titles, and sub
sections, called chapters.

During recording, a title is created between two
points where you start and stop recording.
Chapters will be created automatically when you
finalise recording on DVD-RW/-R discs in Video
mode.
The chapter’s length (interval between chapters)
varies according to the recording mode.

Playing

To play your DVD on other DVD components,
finalising may be necessary. First, finish all editing and
recording operations, then finalise the disc.

When using a DVD-RW disc in VR Mode

Although finalising is generally unnecessary when
playing the disc on a VR Mode compatible
component, a finalised disc should be used for
playback on that type of component.

When using a DVD-RW disc in Video Mode

The disc should be finalised first to enable playback
on anything other than this recorder. No more editing
or recording can be made on the disc once it has
been finalised.
To enable recording on the disc again, disc should be
unfinalised.

When using a DVD-R disc

You should finalise the disc to play it on a component
other than this recorder. You cannot edit or record on
the disc once it has been finalised.

12 - English

Unpacking

Getting Started

Accessories

Check for the supplied accessories below.

Video/Audio Cable

Remote Control

Instruction Manual

RF Cable for TV

Batteries for Remote

Control (AAA Size)

Quick Guide

Setting the Remote Control

You can control certain functions of another
manufacturer’s TV with this remote control.
Control function buttons involve: TV

PROG
INPUT button.

, TV VOL + -, Number buttons, TV MUTE,

STANDBY/ON,

Preparing the Remote Control

Install Batteries in the Remote Control

•

Open the battery cover on the back of the remote control.

•

Insert two AAAbatteries. Make sure that the polarities
(+ and -) are aligned correctly.

•

Replace the battery cover.

If the remote does not operate properly:

•

Check the polarity + - of the batteries (Dry-Cell)

•

Check if the batteries are drained.

•

Check if remote sensor is blocked by obstacles.

•

Check if there is any fluorescent lighting nearby.

Dispose of batteries according to local environmental
regulations. Do not put them in the household trash.

English - 13

To determine whether your television is
compatible, follow the instructions below.

1. Switch your television on.

2. Point the remote control towards the television.

3. Press and hold the

TV STANDBY/ON button and
enter the two-figure code corresponding to the
brand of your television, by pressing the
appropriate number buttons.

Controllable TV Codes

BRAND BUTTON
SAMSUNG 01, 02, 03, 04, 05, 06, 07, 08, 09

Getting Started

AIWA 82
ANAM 10, 11, 12, 13, 14, 15, 16, 17, 18
BANG & OLUFSEN 57
BLAUPUNKT 71
BRANDT 73
BRIONVEGA 57
CGE 52
CONTINENTALEDISON 75
DAEWOO
EMERSON 64
FERGUSON 73
FINLUX 06, 49, 57
FORMENTI 57
FUJITSU 84
GRADIENTE 70
GRUNDIG 49, 52, 71
HITACHI 60, 72, 73, 75
IMPERIAL 52
JVC 61, 79
LG 06, 19, 20, 21, 22, 78
LOEWE 06, 69
LOEWE OPTA 06, 57
MAGNAVOX 40
METZ 57
MITSUBISHI 06, 48, 62, 65
MIVAR 52, 77
NEC 83
NEWSAN 68
NOBLEX 66
NOKIA 74
NORDMENDE 72, 73, 75
PANASONIC 53, 54, 74, 75
PHILIPS 06, 55, 56, 57
PHONOLA 06, 56, 57
PIONEER 58, 59, 73, 74
RADIOLA 06, 56
RADIOMARELLI 57
RCA 45, 46
REX 74
SABA 57, 72, 73, 74, 75
SALORA 74
SANYO 41, 42, 43, 44, 48
SCHNEIDER 06

19, 20, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34

BRAND BUTTON
SELECO 74
SHARP 36, 37, 38, 39, 48
SIEMENS 71
SINGER 57
SINUDYNE 57
SONY 35, 48
TELEAVA 73
TELEFUNKEN 67, 73, 75, 76
THOMSON 72, 73, 75
THOMSON ASIA 80, 81
TOSHIBA 47, 48, 49, 50, 51, 52
WEGA 57
YOKO 06
ZENITH 63

Result: If your television is compatible with the remote

control, it will switch off.
It is now programmed to operate with the remote
control.

■

If several codes are indicated for your

NOTE

television brand, try each one in turn until
you find one that works.

■

If you replace the remote control's
batteries, you must set the brand code
again.

Then you can control the television using the following
buttons after the TV button.

Button Function
TV STANDBY/ON Used to switch the television on and off.

INPUT Used to select an external source.

TV VOL (+ -) Used to adjust the volume of the television.

PROG ( ) Used to select the desired channel.
TV MUTE Used to toggle the sound on and off.
Number Used to input number directly.

■

The various functions will not necessarily

NOTE

work on all televisions. If you encounter
problems, operate the television directly.

14 - English

1 2 3

9

4

6

7

12

13

14

8

11

5

10

Description

Front Panel

Getting Started

1. STANDBY/ON BUTTON

Turns the recorder on and off.

2. DVD BUTTON

Select DVD mode.

3. HDD BUTTON

Select HDD mode.

4. DISC TRAY

Opens to accept a disc.

5. DISPLAY

Displays the playing status, title/ chapter/
time, etc.

6. STOP BUTTON

Stops disc playback.

7. SEARCH/SKIP BUTTONS

Goes to the next title/chapter/track or goes
back to the previous title/chapter/track.

Front Panel Display

8. PROG BUTTONS

Select TV preset Channels. Same as

PROG button on the remote control.

9. AV 2 INPUT

Connect external equipment.

10. DV-INPUT

Connect external digital equipment with a DV
jack. (such as a camcorder)

11. OPEN/CLOSE BUTTON

Opens and closes the disc tray.

12. PLAY/PAUSE BUTTON

Plays a disc or pauses playback or recording.

13. P.SCAN BUTTON

Selects the progressive scan mode.

14. REC BUTTON

Starts recording.

1. Lights when a disc is loaded.

2. Lights in the record mode.

3. Lights to indicate the timer record mode.

4. Lights when a -R/RW/RAM disc is loaded.

5. Playing time/clock/current status indicator.

6. Lights in the progressive scan mode.

English - 15

Rear Panel

Getting Started

Fan

The fan always revolves when the power is on.
Ensure a minimum of 10cm clear space on all sides of
the fan when installing the product.

1. DIGITALAUDIO OUT(OPTICAL)

Connects to an amplifier having a digital optical
audio input jack.

2. DIGITALAUDIO OUT(COAXIAL)

Connects to an amplifier having a digital coaxial
audio input jack.

3. AV AUDIO OUT

Connects to the audio input of external
equipment using audio cables.

4. AV VIDEO OUT(good video quality)

Connects the input of external equipment using a
Video cable.

5. AV S-VIDEO OUT(better video quality)

Connects the input of external equipment using
an S-Video cable.

6. COMPONENT VIDEO OUT(best video quality)

Connects to equipment having Component video
input jacks.

7. AV 1 AUDIO IN

Connects the output of external equipment using
an audio cables.

8. AV 1 VIDEO IN

Connects the output of external equipment using
a video cable.

9. AV 1 S- VIDEO IN

Connects the output of external equipment using
an S-Video cable.

10. ANT IN (In from aerial connector)

11. ANT OUT (TO TV) (Out to TV connector)

■

The Antenna connection does not pass

NOTE

output signal of DVD. To watch a DVD on
your TV, you must connect audio/video
cables.

16 - English

Tour of the Remote Control

1

2

3
4

5

6

7
8

9
10
11

12
13

14
15

16
17

18
19

1. DVD STANDBY/ON Button

2. NUMBER Buttons

3. TV/DVD Button (Not available)

4. DVD Button

Press this to operate DVD.

5. HDD Button

Press this to operate HDD.

6. TV VOL Button

TV volume adjustment

7. REVERSE/FORWARD SKIP Buttons

Press to skip a disc backwards or forwards.

8. REVERSE/FORWARD STEP Buttons

Each press will play one-frame forward or reverse.

9. REVERSE/FORWARD SEARCH Buttons

Press to search a disc backwards or forwards.

10. STOP Button

Press to stop a disc.

11. TITLE LIST/DISC MENU Button

Use this to enter the View Recording list/disc menu.

12. MENU Button

Brings up the HDD & DVD RECORDER’s setup menu.

20

21
22

23
24

25
26

7
9

27
28

29

30
31

32
33

34
35

13. OK/DIRECTION Buttons (

…†œ √

Buttons)

14. RETURN Button

15. INFO Button

This will display current setting or disc status.

16. REC Button

Use to make a recording on HDD/DVD-RAM/-RW/-R
discs.

17. COPY Button

Press this when you copy DVD to HDD or HDD to DVD.
To start copying, press the
screen or press the

COPY button on the title list

COPY button during the playback.

18. REPEAT Button

Allows you to repeat a title, chapter, track or disc.

19. REC PAUSE Button

Use this to pause during recording.

20. TV STANDBY/ON Button

21. AUDIO/TV MUTE Button

Use this to access various audio functions on a disc
(DVD mode).
This operates as sound mute. (TV mode)

22. INPUT Button

Select input signal in external input mode (

PROG,

AV2 or DV input)

23. TV Button

Press this to operate TV.

24. OPEN/CLOSE Button

To open and close the disc tray.

25. CM SKIP Button

When a programme recorded on DVD disc or HDD is
played, the unit can be set to automatically skip a portion
of the programme.

26. PROG Button

Use this to select a TV programme.

27. PLAY/PAUSE Button

Press to play/pause a disc.

28. PLAY LIST/TITLE MENU Button

Use this to return to the Title menu, or to view the
recorded files list.

29. ANYKEY Button

View and select the applicable features under current
status.

30. CANCEL Button

31. SUBTITLE Button

Press this to switch the DVD’s subtitle language.

32. TIMER Button

Press to directly enter the Timer Recording Mode menu.

33. MARKER Button

Use this to bookmark a position while playing a disc.

34. REPEAT A-B Button

Allows you to repeat a title, chapter, track or disc.

35. REC MODE Button

Use this to set the desired Recording time and picture

(XP/SP/LP/EP)

quality.

Getting Started

AV1,

English - 17

Connecting &
Setting Up

This section involves various methods of
connecting the HDD & DVD RECORDER to
other external components and required initial
setting modes.

Connecting & Setting Up

Quick Overview

A Quick Overview presented in this guide will give
you enough information to start using the recorder.

Connecting the HDD & DVD RECORDER

†

Other type of connecting the Video
output cable

†

Other type of connecting the Audio
output cable

†

Connecting AV 1 IN, AV 2 IN, DV input jack

Quick Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Connecting the HDD & DVD RECORDER . . . . . .19

Other type of connecting the Video output cable . .19
Other type of connecting the Audio output cable . .21

Connecting AV 1 IN, AV 2 IN, DV input jack . . . . .23

18 - English

Connecting the

Other type of connecting

HDD & DVD RECORDER

1. Disconnect the aerial cable from your TV and
connect it to
the HDD & DVD RECORDER.

2. Connect ANT OUT (TO TV) connector of the HDD &
DVD RECORDER and the aerial input of your TV
using the supplied aerial cable.

3. Use the Video/Audio Cable to connect ANALOG
AUDIO OUT(R/L)/VIDEO OUT jacks on the HDD &
DVD RECORDER to the Audio &Video jacks on the
TV.

4. Plug in the HDD & DVD RECORDER and TV

5. Turn on the HDD & DVD RECORDER and TV.

6. Press the INPUT button on your TV remote control
until the Video signal from the HDD & DVD
RECORDER appears on the TV screen.

Wall

ANT IN

connector on the rear panel of

the Video output cable

There are several ways to output video signal.
Select one of the following video connecting that
best suits you below.

•

Case 1 : Connecting to a Video (Composite) output

jack

•

Case 2 : Connecting to an S-Video output jack

•

Case 3 : Component Video output jacks

S-Video, Component video and Progressive
Output Modes

•

S-Video and Component video output are available
only if your TV supports S-Video input or
Component video input, respectively. If S-Video or
Component video output does not work, check the
TV connections and the TV input selection settings.

•

Compared to standard interlaced video,
progressive scan doubles the amount of video lines
fed to your TV, resulting in a more stable, flicker­free, clear image than interlaced video. This is only
available with TVs that support progressive scan.

•

Progressive Scan Output (576p)
Consumers should note that not all high definition
television sets are fully compatible with this product
and may cause artifacts to be displayed in the
picture, in case of 576 progressive scan picture
problems, It is recommended that the user switch
the connection to the ‘standard definition’ output. If
there are questions regarding our TV set
compatibility with this model 576p HDD & DVD
RECORDER, please contact our customer service
centre.

Connecting & Setting Up

NOTE

or

or

■

The RF cable connection of this product
sends only signals of TV. You must connect
Audio/Video cables to watch a DVD form your
HDD & DVD RECORDER.

■

Power off HDD & DVD RECORDER, then you
can watch programmes received through 2 RF
cable.

English - 19

Case 1 : Connecting to a Video
(Composite) output jack

Case 2 : Connecting to an S-Video
output jack

1. Connect a video(yellow) cable between the VIDEO
(yellow) OUT jack on HDD & DVD RECORDER and
VIDEO (yellow) INPUT jack on your TV (or AV
amplifier).

•

You will enjoy regular quality images.

2. Connect audio cables (white and red) between the
AUDIO OUT jacks on the HDD & DVD RECORDER
and AUDIO IN jacks on TV (or AV amplifier).
(See pages 21~22)

Connecting & Setting Up

yellow

Video/Audio Cable

yellow

1. Connect an S-Video cable (not included) between the
S-VIDEO OUT jack on HDD & DVD RECORDER and
S-VIDEO INPUT jack on your TV (or AV amplifier).

•

You will enjoy high quality images.

2. Connect audio cables (white and red) between the
AUDIO OUT jacks on HDD & DVD RECORDER and
AUDIO IN jacks on TV (or AV amplifier).

20 - English

Case 3 : Component Video output
jacks

Other type of connecting

1. Connect Component video cables (not supplied)

B,PR

red

) jacks on

blue

green

between the COMPONENT OUT(Y,P
HDD & DVD RECORDER and COMPONENT

IN(Y,PB,PR) jacks on your TV.

•

You will enjoy high quality and accurate colour
reproduction images.

2. Connect audio cables (white and red) between the
AUDIO OUT jacks on the HDD & DVD RECORDER
and AUDIO IN jacks on TV (or AV amplifier).
(See pages 21~22).

3. After connecting, refer to the pages 40~41.

green

the Audio output cable

There are several ways to connect your HDD & DVD
RECORDER. Select the audio connection that best
suits you below.

•

Case 1 : Connecting to your TV

•

Case 2 : Connecting to a stereo amplifier with AV

•

Case 3 : Connecting to an AV amplifier with a

Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.

“DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.

If your TV has audio input jacks, use this connection.

output jacks
digital output jack

Case 1 : Connecting to your TV

Connecting & Setting Up

NOTE

blue
red

■

Make sure that the colour coded connections
match. The Y, P
of your

HDD & DVD RECORDER
connected to the exact corresponding
component input jacks on your TV.

■

Progressive setting is only available when
the

HDD & DVD RECORDER

your TV using component cables.

B

, PRcomponent output jacks

must be

is connected to

yellow

white

red

white

red

English - 21

yellow

Case 2 : Connecting to a stereo
amplifier with AV output jacks

Case 3: Connecting to an AV amplifier
with a digital output jack

If your stereo amplifier only has AUDIO INPUT
jacks(L and R), use the AUDIO OUT jacks.

Connecting & Setting Up

whitered

whitered

If your AV amplifier has a Dolby Digital, MPEG2 or
DTS decoder and a digital input jack, use this
connection. To enjoy Dolby Digital, MPEG2 or DTS
sound, you will need to set up the audio settings.
(See page 37)

or

Front(L)
speaker

Front(R)
speaker

Rear(L)

Front(L)

Rear(R)

Front(R)

Subwoofer Centre

22 - English

Connecting AV 1 IN, AV
2 IN, DV input jack

This allows you to connect your HDD & DVD
RECORDER to other external devices and view or
record their outputs.

•

Case 1 : Connecting a VCR, Set-Top Box(STB) or

•

Case2 : Connecting a Camcorder to the AV 2 IN jacks

•

Case3 : Connecting a Camcorder to the DV IN jack

Connecting a VCR or external device to AUDIO/VIDEO
AV 1 IN jacks of the HDD & DVD RECORDER. You can
record from connected equipment (VCR, STB or DVD).

DVD player to the AV 1 IN jacks

Case 1 : Connecting a VCR, Set-Top
Box(STB) or DVD player to the AV 1 IN

jacks

Case2 : Connecting a Camcorder to
the AV 2 IN jacks

You can also use the AV 2 IN jacks on the front panel of
the HDD & DVD RECORDER. You can record from
connected equipment, such as a camcorder.

When an input source is inserted into AV 2 while
viewing TV, the input will be switched to AV 2
automatically. If the input is not selected automatically,
use

INPUT button to select proper input.

Camcorder

yellow

yellow

white

red

Connecting & Setting Up

NOTE

VCR

STB

DVD

or

■

You can also use the AV 2 IN jacks on
the front panel of the HDD & DVD
RECORDER.

■

When the S-Video jack and Video jack
are both connected, the S-Video jack
will have priority.

■

Copy protected content cannot be
recorded.

white

red

Case 3 : Connecting a Camcorder to
the DV IN jack

If your camcorder has a DV output jack, connect it to
the DV input jack of your HDD & DVD RECORDER.

Camcorder

■

If the input is not selected automatically,
use

NOTE

INPUT button to select proper input.

English - 23

On-Screen Menu

System Setup

System Setup

On-Screen Menu Navigation . . . . . . . . . . . . . . . . .24

Plug & Auto Setup . . . . . . . . . . . . . . . . . . . . . . . . .25

Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . .26

Presetting Channels with the Auto Setup

function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Presetting Channels with the Manual Setup

function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Navigation

The on-screen menus allow you to enable or disable
various functions on your HDD & DVD RECORDER.
Use the following buttons to open and navigate
through the on-screen menus.

HDD

System

Title

Clock Set

Music

Language
Audio

Photo

Video
Parental Control

Programme

Install

Setup

MOVE SELECT RETURN EXIT

MENU Button

1

Press this button on the remote control to open
the on-screen menu.
Press again to exit the on-screen menu.

…†, œ√ Buttons

2

Press these buttons on remote control to move
the selection bar
menu options.

…†, œ √ to cycle through the

Setup

√√

√√

√√

√√

√√

√√

√√

Setting up the Language Options . . . . . . . . . . . . .29

Auto Power Off Setting . . . . . . . . . . . . . . . . . . . . .30

CM Skip Time Setting . . . . . . . . . . . . . . . . . . . . . .31

EP Mode Time Setting . . . . . . . . . . . . . . . . . . . . .32

Setting up the Front Display Options . . . . . . . . . . .33

Automatic Chapter Creator . . . . . . . . . . . . . . . . . .34

Setting up NICAM Options . . . . . . . . . . . . . . . . . .35

DivX(R) Registration . . . . . . . . . . . . . . . . . . . . . . .36

Setting up the Audio Options . . . . . . . . . . . . . . . . .37

Setting up the Video display Options . . . . . . . . . . .38

Setting up the Progressive scan . . . . . . . . . . . . . .40

Canceling the Progressive scan . . . . . . . . . . . . . .41

Setting up the Parental Control . . . . . . . . . . . . . . .42

24 - English

OK Button

3

Press this button on the remote control to confirm any
new settings.

RETURN Button

4

Press this button on the remote control to return to
the Previous MENU screen displayed or to exit the
on-screen MENU.

Plug & Auto Setup

Your HDD & DVD RECORDER will automatically set itself up
when it is plugged in for the first time. TV stations and clock
will be stored in memory. The process takes a few
minutes. Your HDD & DVD RECORDER will then be ready for
use.

Connect the RF cable as indicated on page 19.
(Connecting Your HDD & DVD RECORDER to the

1

TV Using the RF Cable and Audio/Video Cable.)

Auto channel scan will be started.

5

Channel Scan

Scanning...

10%

•

The number of stations automatically stored by the
HDD & DVD RECORDER depends on the number of
stations that it has found.

Plug the HDD & DVD RECORDER into the mains.
“AUTO” in the front panel display flickers.

2

Press a number button to select the language.

3

Press 1 for English

Touche 2 pour Français

Drücken Sie 3 Für Deutsch

Pulse 4 para Español

Premere 5 per Italiano

Druk op 6 voor Nederlands

Press the OK button to start the auto setup.

4

Auto Channel Scan is completed. In 3~4 seconds,
you will see Clock Setting Menu. If you want to

6

start Clock Setting immediately, Press

Auto channel scan completed successfully.

OK

Check the date and time.

OK button.

7

Time

Date

12 : 00 01 / JAN SAT 2005

System Setup

Auto setup will be started.

Check antenna and TV cable connection.

Yes No

•if it is : Correct, press
and time will be saved. If you don't press the
button, the date and time will be saved
automatically after 5 seconds.

• if it is : Incorrect, input correct Time, Date, Year

using …†œ √ buttons or number buttons.
Press

OK button then the date and time will be
saved. When you need to change clock setting,
you can set up it manually. (See page 26)

OK button then the date

OK

English - 25

NOTE

■

Now, HDD & DVD RECORDER is ready
for use. Function for “Plug & Auto Setup”
is fixed already. So if you want to change
this fixed one, you can change it by
Presetting the Stations in OSD
“Presetting Channels with the Manual
setup function” menu. (See page 28)

■

Auto setup function can be performed by
pressing

STOP ( ) on the unit
continuously for 5 seconds or more
during power off with no disc inserted.

Setting the Clock

This menu is used to set the current time.
You need to set the time to use timer recording.

With the unit in Stop mode, press the MENU

1

button

.

System Setup

HDD

Title

Title List

Music

Photo

Programme

Setup

MOVE SELECT RETURN EXIT

Title

√√

Press the …† buttons to select Setup, then press
the

2

OK or √ button.

HDD

System

Title

Clock Set

Music

Language
Audio

Photo

Video
Parental Control

Programme

Install

Setup

MOVE SELECT RETURN EXIT

Setup

√√

√√

√√

√√

√√

√√

√√

Press the …† buttons to select Clock Set, then
press the

3

Press the

OK or √ button.

…†œ √ buttons to input Time, Date or

Year. Press the number buttons to input clock
data directly.
The day of the week is displayed automatically.

26 - English

HDD
Title

Time Date

Music

12 : 00 01 / JAN SAT 2005

Photo

Programme

Setup

0~9 NUMBER SELECT RETURN EXIT

Clock Set

Press the OK button, then the date and time will
be saved. If you don’t press the

4

OK button, it will

not be saved.

Presetting Channels with

4

the Auto Setup function

Press the …† buttons to select Auto Setup, then
press the

OK or √ button.
The message “Your data will be lost. Press [OK]
to continue, [Return] to exit.” is displayed.

This feature allows you to manually set the HDD & DVD
RECORDER tuner band to Antenna or Cable,
whichever you connected to the Antenna In jack during
initial setup.

With the unit in Stop mode, press the MENU

1

button

.

Press the …† buttons to select Setup, then press
the

2

OK or √ button.

HDD

System

Title

Clock Set

Music

Language
Audio

Photo

Video
Parental Control

Programme

Install

Setup

MOVE SELECT RETURN EXIT

Setup

√√

√√

√√

√√

√√

√√

√√

Press the …† buttons to select Install, then press
the

3

OK or √ button.

HDD

Auto Setup

Title

Manual Setup

Music

Photo

Programme

Setup

MOVE SELECT RETURN EXIT

Install

√√

√√

HDD

Title

Music

Your data will be lost.

Press [OK] to continue, [Return] to exit.

Photo

Programme

Setup

OK

SELECT RETURN EXIT

Install

Press the OK button. If you want to exit, press the

5

MENU button.

HDD

Title

Music

Photo

Programme

Setup

Please wait.

Scanning...

SELECT RETURN EXIT

Auto Setup

11%

Stop

• The first frequency band is scanned and the first

station found is displayed and stored. And the
HDD & DVD RECORDER searches for the
second station and so on.

• When the automatic scanning procedure has

finished, the HDD & DVD RECORDER switches
automatically to programme 1.

• The number of stations automatically stored by

the HDD & DVD RECORDER depends on the
number of stations that it has found.

System Setup

Channel scan will be started. Press the OK button
to stop the Auto Setup.

6

English - 27

Presetting Channels with

5

the Manual Setup function

Press the …† buttons to select a PR(programme)
you wish to edit, delete, or swap, then press the
ANYKEY button.
Select

Edit, Delete or Swap.

You can add preset channel that Auto Channel Search
missed. And you can delete a channel you wish to
remove. You can programme the order of channels.

With the unit in Stop mode, press the MENU

1

button.

Press the …†buttons to select Setup, then press

2

System Setup

OK or √ button.

the

HDD
Title

Music

Photo

Programme

Setup

Setup

System
Clock Set
Language
Audio
Video
Parental Control
Install

MOVE SELECT RETURN EXIT

√√

√√

√√

√√

√√

√√

√√

Press the …†buttons to select Install, then

3

press the

OK or √ button.

HDD

Auto Setup

Title

Manual Setup

Music

Photo

Programme

Setup

MOVE SELECT RETURN EXIT

Install

√√

√√

Press the …†buttons to select Manual Setup,
then press the

4

OK or √ button.

Manual Setup

PR CH Name
01 - - - - - - ­02 - - - - - - ­03 - - - - - - ­04 - - - - - - ­05 - - - - - - ­06 - - - - - - ­07 - - - - - - -

MOVE SELECT RETURN EXIT

Manual Setup

PR CH Name
01 - - - - - - ­02 - - - - - - ­03 - - - - - - ­04 - - - - - - ­05 - - - - - - -

Edit

06 - - - - - - -

Delete

07 - - - - - - -

Swap

MOVE SELECT RETURN EXIT

•

In case of Edit : You can add or edit
PR(programme) information. After change PR
informations (
press the

-

CH : Tune the channel using œ √ buttons.

-

Name : Display station name automatically detected

CH, Name, MFT), select Save, then

OK button.

Manual Setup

PR 01
CH 02
Name - - - ­MFT - - - - - -

Save

MOVE SELECT

in broadcasting signal. If not detected, you
can edit name by using

-

MFT(Manual Frequency Tunning) : You can tune
up the channel frequency better using

•

In case of Delete : the channel information of

…†œ √ buttons.

œ √ buttons.

selected PR(programme) will be removed.

In case of Swap : You can swap the channel

•
information of two PR(programme). For example,
if you wish to swap PR2 and PR5, select swap at
PR2, then press the

OK button at PR5.

28 - English

Setting up the Language
Options

If you set the audio, subtitle, disc menu and on-screen
menu, in advance, they will come up automatically
every time you watch a movie.
If the selected language is not recorded on the disc, the
original pre-recorded language is selected.

Press the …†buttons to select the desired
language option, press the

4

HDD

Audio : Original

Title

Subtitle : Automatic

Music

Disc Menu : English
On-Screen menu : English

Photo

Programme

Setup

MOVE SELECT RETURN EXIT

OK or √ button.

Language

Original

English
Français
Deutsch
Español
Italiano
Nederlands
Korean

√√

√√

√√

√√

With the unit in Stop mode, press the MENU

1

button.

Press the …† buttons to select Setup,
then press the

2

OK or √ button.

HDD

System

Title

Clock Set

Music

Language
Audio

Photo

Video
Parental Control

Programme

Install

Setup

MOVE SELECT RETURN EXIT

Press the …†buttons to select Language,
then press the

3

OK or √ button.

Language setup menu will be displayed.

HDD

Audio : Original

Title

Subtitle : Automatic

Music

Disc Menu : English
On-Screen menu : English

Photo

Programme

Setup

MOVE SELECT RETURN EXIT

Language

Setup

• Audio : For the disc audio language.

• Subtitle : For the disc subtitles.

• Disc Menu: For the disc menu contained on the

disc

• On-Screen menu:

For the on-screen menu of your

System Setup

HDD & DVD RECORDER.

Press the …†buttons to select the desired

5

√√

√√

√√

√√

√√

√√

√√

language, then press the

■

Press the RETURN or œ button to return

NOTE

to the previous menu. Press the

OK or √ button.

MENU

button to exit the menu.

■

The selected language will only appear if
it is supported on the disc.

√√

√√

√√

√√

English - 29

Auto Power Off Setting

This feature automatically turns off your HDD & DVD
RECORDER, if you do not press any button for the
selected time.

With the unit in Stop mode, press the MENU

1

button.

Press the …† buttons to select Setup, then press

2

OK or √ button.

the

Press the …† buttons to select the desired item,
then press the

5

•

Off : Auto power off is disabled.

•

2 Hour : DVD-HDD Receiver will automatically

OK or √ button.

turns off for 2 hours after the last button
is pressed.

•

6 Hour : DVD-HDD Receiver will automatically

turns off for 6 hours after the last button
is pressed.

•

If turn off time set by automatic Power off
function is reached during a playback or
recording, the device will operate until the
playback or recording is over.

System Setup

Press the …† buttons to select System,

3

then press the
System menu will be displayed.

Press the …† buttons to select Auto Power Off,
then press the

4

HDD

System

Title

Clock Set

Music

Language
Audio

Photo

Video
Parental Control

Programme

Install

Setup

MOVE SELECT RETURN EXIT

OK or √ button.

HDD

Auto Power Off : Off

Title

CM Skip Time : 15 Sec

Music

EP Mode Time : 6 Hour
Front Display : Auto Dim

Photo

Chapter Creator : Off
NICAM : On

Programme

DivX(R) Registration

Setup

MOVE SELECT RETURN EXIT

OK or √ button.

Setup

System

√√

√√

√√

√√

√√

√√

√√

√√

√√

√√

√√

√√

√√

√√

30 - English

HDD

Auto Power Off : Off

Title

CM Skip Time : 15 Sec

Music

EP Mode Time : 6 Hour
Front Display : Auto Dim

Photo

Chapter Creator : Off
NICAM : On

Programme

DivX(R) Registration

Setup

MOVE SELECT RETURN EXIT

Off

2 Hour
6 Hour

System

√√

√√

√√

√√

√√

√√

√√