Samsung DVD-HR710 User Manual

Instruction Manual

DVD-HR710 DVD-HR721

English

www.samsung.com

AK68-00903E-01

Warning

IMPORTANT NOTE

The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug. If it requires replacing, a fuse approved to BS1362 of the same rating must be used.

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Getting Started

This symbol indicates “dangerous voltage” inside the product that presents a risk of electric shock or personal injury.

This symbol indicates important instructions accompanying the product.

Do not install this equipment in a confined space such as a bookcase or similar unit.

WARNING :

CAUTION : HDD & DVD RECORDER USES AN INVISIBLE

CAUTION

THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture.

LASER BEAM WHICH CAN CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE HDD & DVD RECORDER CORRECTLY AS INSTRUCTED.

Never use the plug with the fuse cover omitted if the cover is detachable. If a replacement fuse cover is required, it must be of the same colour as the pin face of the plug. Replacement covers are available from your dealer.

If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should obtain a suitable safety approved extension lead or consult your dealer for assistance.

However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect the plug to a mains jack, as there is a risk of shock hazard from the bared flexible cord.

The product unit accompanying this user manual is licenced under certain intellectual property rights of certain third parties. This licence is limited to private noncommercial use by end-user consumers for licenced contents. No rights are granted for commercial use. The licence does not cover any product unit other than this product unit and the licence does not extend to any unlicenced product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit. The licence only covers the use of this product unit to encode and/or decode audio files conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this licence for product features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.

This product satisfies CE regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances, such as radios and televisions, use shielded cables and connectors for connections.

2- English

Precaution

Important Safety Instructions

Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings, Install in accordance with the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades with one wider than the other. A groundingtype plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. if the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Handling Cautions

• Before connecting other components to this HDD & DVD RECORDER, be sure to turn them all off.

• Do not move the HDD & DVD RECORDER while a disc is being played, or the disc may be scratched or broken, the HDD & DVD RECORDER internal parts may be damaged.

Do not put a flower vase filled with water or any

• small metal objects on the HDD & DVD RECORDER.

• Be careful not to put your hand into the disc tray.

• Do not place anything other than the disc in the disc tray.

• Exterior interference such as lightning and static electricity can affect normal operation of this HDD & DVD RECORDER. If this occurs, turn the HDD & DVD RECORDER off and on again with the

STANDBY/ON

reconnect the AC power cord to the AC power outlet. The HDD & DVD RECORDER will operate normally.

• Be sure to remove the disc and turn off the HDD & DVD RECORDER after use.

• Disconnect the AC power cord from the AC outlet when you don’t intend to use the HDD & DVD RECORDER for long periods of time.

• Clean the disc by wiping in a straight line from the inside to the outside of the disc.

button, or disconnect and then

DVD

Maintenance of Cabinet

For safety reasons, be sure to disconnect the AC power cord from the AC outlet.

•

Do not use benzene, thinner, or other solvents for cleaning.

•

Wipe the cabinet with a soft cloth.

HDD (Hard Disk Drive)

The hard disk has a high storage density, which enables long recording durations and quick access to written data. However, it can easily be damaged by shock, vibration or dust and should be kept away from magnets. To avioid losing important data, observe the following precautions.

• Do not use the HDD & DVD RECORDER in a place subject to extreame changes in temperature.

• Do not apply a strong shock to the HDD & DVD RECORDER.

• Do not place the HDD & DVD RECORDER in a location subject to mechanical vibrations or in an unstable location.

English - 3

Getting Started

• Do not place the HDD & DVD RECORDER on top of a heat source.

• Do not disconnect the AC power cord while the power is on.

• Do not attempt to change the hard disk. This may result in a malfunction.

Should the hard disk be damaged, you cannot recover lost data. The hard disk is only a temporary storage space.

use discs fixed with exposed tape adhesive or leftover peeled-off stickers.)

• Do not use scratch-proof protectors or covers.

• Do not use discs printed with label printers available on the market.

• Do not load warped or cracked discs.

Disc Storage

Getting Started

Disc Handling

• Use discs with regular shapes. If an irregular disc (a disc with a special shape) is used, this HDD & DVD RECORDER may be damaged.

Holding discs

• Avoid touching the surface of a disc where recording is performed.

DVD-RAM, DVD-RW and DVD-R

• Clean with an optional DVD-RAM/PD disc cleaner (LF-K200DCA1 where available). Do not use cleaners or cloths for CDs to clean DVD-RAM/

-RW/-R discs.

DVD-Video, Audio-CD

• Wipe off dirt or contamination on the disc with a soft cloth.

Cautions on handling discs

Be careful not to harm the disc because the data on these discs is highly vulnerable to the environment.

• Do not keep under direct sunlight.

• Keep in a cool ventilated area.

• Store vertically.

• Keep in a clean protection jacket.

• If you move your HDD & DVD RECORDER suddenly from a cold place to a warm place, condensation may generate on the operating parts and lens and cause abnormal disc playback. If this occurs, do not connect the plug to the power outlet and wait for two hours. Then insert the disc and try to play back again.

Disc Specifications

Disc Type

DVD-Video

• A digital versatile disc (DVD) can contain up to 135minutes of images, 8 audio languages and 32 subtitle languages. It is equipped with MPEG-2 picture compression and Dolby digital surrounding, allowing you to enjoy vivid and clear theatre quality images in the comfort of your own home.

• When switching from the first layer to the second layer of a dual-layered DVD Video disc, there may be momentary distortion in the image and sound. This is not a malfunction of the unit.

• Once a DVD-RW/-R recorded in Video Mode is finalised, it becomes DVD-Video.

• Do not write on the printed side with a ball-point pen or pencil.

• Do not use record cleaning sprays or antistatic. Also, do not use volatile chemicals, such as benzene or thinner.

• Do not apply labels or stickers to discs. (Do not

4- English

Audio CD

DVD-RW Disc Playback and Recording

• An audio disc on which 44.1kHz PCM Audio is recorded.

• Plays CD-DA format audio CD-R and CD-RW discs.

• The unit may not be able to play some CD-R or CDRW discs due to the condition of the recording.

CD-RW/-R

• Use a 700MB(80 minutes) CD-R/RW disc. If possible, do not use a 800MB(90 minutes) or above disc, as the disc may not play back.

• If the CD-R/RW disc was not recorded as a closed session, you may experience a delay in the early playback time, all recorded files may not play.

• Some CD-R/RW discs may not be playable with this unit, depending on the device which was used to burn them. For contents recorded on CD-R/RW media from CDs for your personal use, playability may vary

depending on contents and discs.

DVD-R Disc Playback and Recording

• Once a DVD-R recorded in Video Mode is finalised, it becomes DVD-Video.

• You can record onto the available space on the disc and perform editing functions such as giving titles to discs and programmes and erasing programmes before finalising.

• When programming is erased from a DVD-R, that space does not become available. Once an area on a DVD-R is recorded on, that area is no longer available for recording, whether the recording is erased or not.

• It takes about 30 seconds for the unit to complete recording management information after recording finishes.

• This product optimizes the DVD-R for each recording. Optimizing is carried out when you start recording after inserting the disc or turning on the unit. Recording onto the disc may become impossible if optimizing is carried out too many times.

• Playback may be impossible in some cases due to the condition of recording.

• This unit can play back DVD-R discs recorded and finalised with a Samsung DVD video recorder. It may not be able to play some DVD-R discs depending on the disc and the condition of the recording.

• Recording and playback can be performed on DVDRW discs in both the Video and VR Modes.

• Once a DVD-RW recorded in both the Video and VR Modes is finalised, you cannot perform addtional recording.

• Once a DVD-RW recorded in Video Mode is finalised, it becomes DVD-Video.

• In both modes, playback can be performed before and after finalisation, but additional recording, deleting and editing can not be performed after finalisation.

• If you want to record the disc in VR Mode and then record in V Mode, be sure to execute Format. Be careful when executing Format because all the recorded data may be lost.

• A DVD-RW blank disc is initialized to VR Mode when first initialized.

DVD-RAM Disc Playback and Recording

• Ensure that the recording mode is set to VR mode. Otherwise, this product will not be able to play the recording.

• You cannot play a DVD-RAM in most DVD components due to compatibility issues.

• Only DVD-RAM standard Version 2.0. discs can be played in this unit.

• DVD-RAM recorded on this unit may not work with other DVD components. To determine compatibility with these DVD-RAM discs, refer to the user’s manual for the player.

• For cartridge type DVD-RAM discs, remove the cartridge and use the disc only.

Disc Copy

Contents Copy Specifications

Contents HDD Recorded Video Title Supported Supported Copy Protected Title Not supported Not supported

Copy Once

MP3 Not supported supported JPEG(photo) Not supported supported DivX Not supported Not supported

Title

➞ DVD DVD ➞

Move

(Deletes the Title in the

HDD after copying)

HDD

Not supported

Getting Started

Once "Copy Once programme" has been recorded on the DVD disc, this title cannot be copied to HDD anymore. But "Copy Once programme" has been recorded on the HDD, this title can be copied to DVD-RW(VR mode) or DVD-RAM.

English - 5

COPY PROTECTION

• Many DVD discs are encoded with copy protection. Because of this, you should only connect your HDD & DVD RECORDER directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy-protected DVD discs.

• This product incorporates copyright protection technology that is protected by methods claims of certain U.S. patents and other intellectual

Getting Started

property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorised by Macrovision Corporation, is intended for home and other limited viewing uses only unless otherwise authorised by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Protection

This HDD & DVD RECORDER can allow you to protect the contents of your discs, as described below.

• Programme-protected: See page 95 “Locking(Protecting) a Title”

• Disc-protected: See page 120 “Disc Protection”

❋

DVD-RAM/-RW/-R discs that are incompatible with the DVD-VIDEO format cannot be played with this product.

❋

For more information on DVD recording compatibility, consult your DVD-RAM/-RW/-R manufacturer.

❋

Use of poor quality DVD-RAM/-RW/-R discs may cause following unexpected problems including, without limitation, recording failure, loss of recorded or edited materials or damage to the HDD & DVD RECORDER.

Using JPEG disc

• CD-R, DVD-R/RW/RAM, HDD with JPEG files recorded with UDF, ISO9660 or JOLIET format can be playbacked.

• Only JPEG files with the “.jpg” or “.JPG” extension can be displayed.

• The unit can handle a maximum of 4,500 files and 1,000 sub folders under a folder.

• MOTION JPEG and progressive JPEG are not supported.

Using MPEG4 disc

• Disc : CD-RW/-R, DVD-RAM/-RW/-R

• MPEG4 File with following extensions can be played. : .avi, .divx, .AVI, .DIVX

• MPEG4 Codec format : DivX 3.11 DivX 4.x DivX 5.x (without QPEL and GMC)

• Available Audio Format : “MP3”, “MPEG”, “WMA”, “LPCM”, “AC3”

• Supported subtitle file formats: .smi, .srt, .sub, .psb, .txt, .ass

DVD-RAM/-RW (VR)

• This is a format that is used for recording data on a DVD-RAM or DVD-RW disc. You can record multiple titles, edit, delete, partial delete, create a playlist, etc.

• A disc that is recorded in this mode may not be played by existing HDD & DVD RECORDER.

Disc Format

Using MP3 disc

• CD-R, DVD-R/RW/RAM, HDD with MP3 files recorded with UDF, ISO9660 or JOLIET format can be playbacked.

• Only MP3 files with the “.mp3” or “.MP3” extension can be played.

• For MP3 files recorded with a VBR(Variable Bit Rates), from 32 Kbps to 320 Kbps, the sound may cut in out.

• Playable bit-rate range is from 56 Kbps to 320 Kbps.

• The unit can handle a maximum of 1,500 files and 1,000 sub folders under a folder

6- English

DVD-RW (V)/-R

• This is a format that is used for recording data on a DVD-RW or DVD-R disc. The disc can be played by existing HDD & DVD RECORDER once it has been finalised.

• If a disc that has been recorded in Video Mode by a different maker’s recorder but has not been finalised, it cannot be played or additionally be recorded by this HDD & DVD RECORDER.

Do not use the following discs!

• LD, CD-G, CD-I, CD-ROM, DVD-ROM, DVD+R and DVD+RW discs should not be used in this product. [Note] Disc types that can be played : CD/CD-R/-RW/ MP3/JPEG/DVD-Video/DVD-RAM/-RW/-R. For a DVD-RW/-R disc, which has been recorded in Video Mode on another component, it can play only when finalised.

• Some commercial discs and DVD discs purchased outside your region may not be playable with this product. When these discs are played, either “No disc.” or “Please check the regional code of the disc.” will be displayed.

• If your DVD-RW disc is an illegal copy or is not in DVD video format, it may also not be playable.

Disc compatibility

• High Speed Recording discs can be used in this unit.

• Not all brands of discs will be compatible with this unit.

Getting Started

English - 7

Contents

Getting Started

Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Getting Started

Precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . .3

Handling Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Maintenance of Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . .3

HDD (Hard Disk Drive) . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Disc Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Disc Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Disc Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Disc Copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

General Features . . . . . . . . . . . . . . . . . . . . . . . . . .10

Before Reading the User’s Manual . . . . . . . . . . .11

How to use the HDD & DVD RECORDER . . . . . .11

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Front Panel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Tour of the Remote Control . . . . . . . . . . . . . . . . . . . . . .17

Connecting & Setting Up

Quick Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Connecting the HDD & DVD RECORDER Additional connections Antenna + HDD & DVD RECORDER + External decoder box + TV Other type of connecting the Video output cable

Case 1 : Connecting to a Video (Composite)

output jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Case 2 : Connecting to an S-Video output jack . . . . . .21

Case 3 : Component Video output jacks . . . . . . . . . . .22

Other type of connecting the Audio output cable

Case 1 : Connecting to your TV . . . . . . . . . . . . . . . . . .22

Case 2 : Connecting to a stereo amplifier

with AV output jacks . . . . . . . . . . . . . . . . . . . . . . . . . . .23

. . . . . . . . . . . . . . . . . . . . .19

. . . . . . . . . . . . . . . . . . . . . . . . . 20

. . . . . .19

. .20

. . . .22

Case 3: Connecting to an AV amplifier

with a digital output jack .................................................23

Connecting to AV 3 IN, DV input jack...................24

Case 1 : Connecting a VCR, Set-Top Box(STB), DVD player or Camcorder to the AV3 IN jacks Case 2 : Connecting a Camcorder to the

DV IN jack ..............................................................24

System Setup

On-Screen Menu Navigation..................................25

Plug & Auto Setup ...................................................26

Setting the Clock......................................................27

Presetting Channels with the Auto Setup function Presetting Channels with the Manual Setup

function......................................................................30

Setting up the Language Options.........................31

Auto Power Off Setting...........................................32

CM Skip Time Setting..............................................33

EP Mode Time Setting.............................................34

Setting up the Front Display Options ..................35

Automatic Chapter Creator....................................36

Setting up NICAM Options.....................................37

DivX(R) Registration................................................38

Setting up the Audio Options................................38

Setting up the Video display Options ..................40

Setting up Video Output Options..........................41

Setting up the Progressive scan...........................42

Canceling the Progressive scan...........................43

Setting up the Parental Control.............................44

If you forgot your password ............................................44

Setting the Rating Level..................................................45

Changing the Password .................................................45

Playback

Before Playing..........................................................46

Playing a Disc...........................................................47

Using the Disc Menu & Title Menu .......................48

Using the Search & Skip Functions .....................48

Slow Motion Play/Step Motion Play......................49

About ANYKEY.........................................................50

Playing the Title List................................................52

........24

.....28

8- English

Navigation Menu......................................................53

Using Markers ..........................................................56

Using the Bookmarks .............................................58

Selecting the Subtitle Language...........................60

Selecting the Soundtracks & Audio Channels...61

Changing the Camera Angle..................................62

Repeat Play...............................................................62

Zooming-In................................................................64

Select Media..............................................................65

Playing an Audio CD/MP3 ......................................65

Viewing a Picture .....................................................72

Playing an MPEG4...................................................75

Recording

Before Recording.....................................................77

Recording the current TV programme you are

watching....................................................................79

Recording from external equipment

you are watching .....................................................81

Copying from a Camcorder ...................................82

Making a One T ouch Recording (OTR)................83

Chasing Play.............................................................84

Simultaneous Recording and Playback..............85

Making a Timer Recording ....................................86

Flexible Recording (for Timer recording only) ...88

Editing the Timer Record List................................88

Deleting a Timer Record List.................................89

Go To History List....................................................90

Copying from HDD to DVD..................................109

About the Copy Screen ................................................109

Changing the Record Mode .........................................112

Copying Multiple Titles at One Time..................112

Deleting an Undesired Title from the Copy List ...........114

Previewing a Selected Title from the Copy List ...........114

Selecting Record Mode of Each Title

from the Copy List. ........................................................115

Changing Record Mode of All Titles

from the Copy List .........................................................115

Copying from DVD to HDD..................................116

Copying MP3 or JPEG Files

from a Disc to HDD ..............................................117

File Copy ........................................................................117

Folder Copy ...................................................................118

Disc Manager .........................................................119

Editing the Disc Name ..................................................119

Disc Protection ..............................................................120

Formatting a Disc ..........................................................121

Delete All Title Lists/Music Lists/Photo Lists................122

Delete All Title Lists ......................................................123

Finalising a Disc ...........................................................124

Unfinalising a Disc (V/VR mode) .................................125

Reference

Troubleshooting.....................................................126

Specifications ........................................................130

Getting Started

Editing

Basic Editing (Title List) .........................................94

Renaming(Labeling) a Title.............................................94

Locking (Protecting) a Title ............................................95

Deleting a Title.................................................................96

Splitting a Section of a Title (Split)..................................97

Deleting a Section of a Title (Partial Delete)..................99

Advanced Editing (Playlist) .................................101

Creating a Playlist .........................................................101

Playing Entries in the Playlist .......................................102

Renaming a Playlist Entry ............................................103

Editing a Scene for the Playlist.....................................104

Deleting a Playlist Entry from the Playlist ....................108

English - 9

General Features

The HDD(Hard Disk Drive) & DVD RECORDER allows you to record and play high quality digital video on DVDRAM/-RW/-R discs or on the HDD. You can also edit digital images on DVD-RAM/-RW/-R discs or HDD.

Getting Started

HDD Recording

• DVD-HR710

You can record up to 127 hours of video (in EP mode) on the internal 80GB (gigabyte) hard disk (HDD).

• DVD-HR721

You can record up to 272 hours of video (in EP mode) on the internal 160GB (gigabyte) hard disk (HDD).

With both recordable DVD and a high-capacity HDD in the same recorder, you have the flexibility to keep recordings on the HDD for quick access anytime, or record to DVD for archiving or playing on other DVD players.

Copy between HDD and DVD

You can copy recordings from the HDD to recordable DVD, or from DVD to the HDD. Usually you can use the high speed copy feature. You can also choose to copy material at a different recording quality from the original. For example, you might want to copy at XP mode (highest quality) recording on the HDD to SP (standard play) quality on a DVD so that you can fit other recordings on the same disc.

Simultaneous Recording and Playback

Playback and recording for both the DVD and the built-in hard disk drive (HDD) are completely independent. For example you can record a broadcast programme to either a recordable DVD or the HDD, while watching another recording you already made on the same DVD or on the HDD.

recording time, LP & SP modes provide less recording time with higher quality recording, XP mode gives you the highest quality recording.

Automated Quality Adjustment for Timer Recording

If FR mode is selected, the video quality is adjusted automatically so that all video for the scheduled time can be recorded onto the free disc space. (See page 88)

Creating a DVD video title using DVD-RW/-R disc

With the HDD & DVD RECORDER, you can create your own DVD Video titles on 4.7 GB DVD-RW/-R discs.

Copying data from a digital camcorder using a DV input jack

Record DV Device video onto HDD and DVD-RAM/-RW/-R discs using the DV input jack (IEEE 1394-4pin/4pin). (See page 82)

High quality progressive scan

Progressive scanning provides high resolution and flicker free video. The 10-bit 54-MHz DAC and 2D Y/C Separating Circuitry provides the highest image playback and recording quality. (See pages 42~43)

A variety of functions with an easy-to-use user interface

The integrated menu system allows you to perform desired operations both easily and conveniently. With a HDD,

DVD-RAM or DVD-RW disc, you can edit recorded video, create a playlist, edit video in a specific sequence according to your requirements.

MPEG4 playback

This HDD & DVD RECORDER can play MPEG4 formats within an avi file.

High quality digital audio and video recording and playback

Record up to 16-hours of video with a double sided 9.4 GB DVD-RAM disc, up to 8-hours of video with a 4.7 GB DVD-RAM/-RW/-R disc, depending on the recording mode.

Selectable Recording Mode

You can set your HDD & DVD RECORDER to one of four different recording speeds, each varying in recording quality and length. EP (6Hr or 8Hr) mode yields the most

10 - English

DivX Certification

DivX, DivX Certified, and associated logos are trademarks of DivXNetworks, Inc and are used under licence.

Before Reading the User’s Manual

Make sure to check the following terms before reading the user manual.

Icons that will be used in manual

Icon Term Definition

HDD

DVD

RAM

JPEG on CD-R/-RW or DVD-R/-RW/

MP3

MPEG4 on CD-R/-RW or DVD-R/-RW/

Caution function does not operate or

NOTE on the page that help each

One-Touch

button by using only one button.

ANYKEY A function that can be operated

button by using

About the use of this user’s manual

1) Be sure to be familiar with Safety Instructions before using this product. (See pages 2~7)

2) If a problem occurs, check the Troubleshooting. (See pages 126~129)

This involves a function available on the HDD.

This involves a function available on DVD or DVD-R/DVD-RW discs that have been recorded and finalised in Video Mode.

This involves a function available on DVD-RAM.

This involves a function available on DVD-RW.

This involves a function available

on DVD-R.

This involves a function available on a data CD (CD-R or CD-RW).

This involves a function available

-RAM discs.

This involves a function available on CD-R/-RW or DVD-R/-RW/

-RAM discs.

This involves a function available

-RAM discs.

This involves a case where a

settings may be cancelled.

This involves tips or instructions

function operate.

A function that can be operated

ANYKEY button.

How to use the HDD & DVD RECORDER

Step 1

This unit can record on the following types of discs. If you want to repeatedly record on the same disc or you want to edit the disc after recording, select a rewritable DVD-RW or DVD-RAM type disc. If you want to save a recording without any changes, choose a non-rewritable DVD-R. You can record files directly to the built-in HDD or edit a recorded file.

Step 2

Unlike a VCR, the HDD & DVD RECORDER automatically starts formatting when an unused disc is inserted. This is required for the preparation of recording on a disc.

Using the HDD

Formatting unneccessory.

Using a DVD-RAM

This type of disc can be formatted in DVD-Video Recording format (VR mode). You can edit recorded video and create a playlist and edit video in a specific sequence according to your requirements.

Using a DVD-RW

This type of disc can be formatted in either DVD-Video format (V mode) or DVD-Video Recording format (VR mode). For an unused disc, a message that asks whether to format in VR Mode or not is displayed. You can play a Video mode disc on various DVD components. A VR mode disc allows more varied editing.

Using a DVD-R

This type of disc can be formatted in DVD Video format. After formatting is complete, you can record on the disc. You can play these type of discs on various DVD components only when they have been finalised.

Select the disc type or HDD

Format the disc to start recording

Getting Started

English - 11

■

You can only use either the VR or Video

NOTE

mode on a DVD-RW, but not both at the same time.

■

You can change the DVD-RW to format to another format by reinitializing. It should be noted that the disc's data will be lost when changing formats.

Getting Started

Step 3

There are two different recording methods, Direct Recording and Timer Recording. Timer recording is classified as follows:

Recording mode : XP (high quality mode), SP (standard quality mode), LP (long recording mode), and EP (extended mode) according to the recording mode. When recording is set in the FR mode, the best quality picture is recorded with regards to the remaining time on the disc.

Recording

Step 5

Editing on discs is easier than conventional video tapes. The HDD & DVD RECORDER supports many different edit functions, possible only with DVDs and HDD.

With a simple and easy edit menu, you can operate various edit functions, such as delete, copy, rename, lock, etc., on a recorded title.

Creating a playlist (DVD-RAM/-RW in VR mode, HDD)

With this HDD & DVD RECORDER, you can create a new playlist on a disc and edit it without the original, pre-existing recording.

Step 6

Editing a recorded disc

Finalising & Playing on other DVD components

Step 4

You can select the title you want to play in a displayed menu and then immediately start playback.

A DVD consists of sections, called titles, and subsections, called chapters.

During recording, a title is created between two points where you start and stop recording. Chapters will be created automatically when you finalise recording on DVD-RW/-R discs in Video mode. The chapter’s length (interval between chapters) varies according to the recording mode.

Playing

To play your DVD on other DVD components, finalising may be necessary. First, finish all editing and recording operations, then finalise the disc.

When using a DVD-RW disc in VR Mode

DVD discs recorded in VR mode can only be played back in DVD recorders, not players.

When using a DVD-RW disc in Video Mode

The disc should be finalised first to enable playback on anything other than this HDD & DVD RECORDER. No more editing or recording can be made on the disc once it has been finalised. To enable recording on the disc again, the disc must be unfinalised.

When using a DVD-R disc

You should finalise the disc to play it on a component other than this HDD & DVD RECORDER. You cannot edit or record on the disc once it has been finalised.

12 - English

Unpacking

Getting Started

Accessories

Check for the supplied accessories below.

Video/Audio Cable

Remote Control

Instruction Manual

RF Cable for TV

Batteries for Remote

Control (AAA Size)

Quick Guide

Setting the Remote Control

You can control certain functions of another manufacturer’s TV with this remote control. Control function buttons involve: TV

PROG INPUT button.

, TV VOL + -, Number buttons, TV MUTE,

STANDBY/ON,

Preparing the Remote Control

Install Batteries in the Remote Control

•

Open the battery cover on the back of the remote control.

•

Insert two AAA batteries. Make sure that the polarities (+ and -) are aligned correctly.

•

Replace the battery cover.

If the remote does not operate properly:

•

Check the polarity + - of the batteries (Dry-Cell)

•

Check if the batteries are drained.

•

Check if remote sensor is blocked by obstacles.

•

Check if there is any fluorescent lighting nearby.

Dispose of batteries according to local environmental regulations. Do not put them in the household trash.

English - 13

To determine whether your television is compatible, follow the instructions below.

1. Switch your television on.

2. Point the remote control towards the television.

3. Press and hold the

TV STANDBY/ON button and

enter the two-figure code corresponding to the brand of your television, by pressing the appropriate number buttons.

Controllable TV Codes

BRAND BUTTON SAMSUNG 01, 02, 03, 04, 05, 06, 07, 08, 09

Getting Started

AIWA 82 ANAM 10, 11, 12, 13, 14, 15, 16, 17, 18 BANG & OLUFSEN 57 BLAUPUNKT 71 BRANDT 73 BRIONVEGA 57 CGE 52 CONTINENTAL EDISON 75 DAEWOO EMERSON 64 FERGUSON 73 FINLUX 06, 49, 57 FORMENTI 57 FUJITSU 84 GRADIENTE 70 GRUNDIG 49, 52, 71 HITACHI 60, 72, 73, 75 IMPERIAL 52 JVC 61, 79 LG 06, 19, 20, 21, 22, 78 LOEWE 06, 69 LOEWE OPTA 06, 57 MAGNAVOX 40 METZ 57 MITSUBISHI 06, 48, 62, 65 MIVAR 52, 77 NEC 83 NEWSAN 68 NOBLEX 66 NOKIA 74 NORDMENDE 72, 73, 75 PANASONIC 53, 54, 74, 75 PHILIPS 06, 55, 56, 57 PHONOLA 06, 56, 57 PIONEER 58, 59, 73, 74 RADIOLA 06, 56 RADIOMARELLI 57 RCA 45, 46 REX 74 SABA 57, 72, 73, 74, 75 SALORA 74 SANYO 41, 42, 43, 44, 48 SCHNEIDER 06

19, 20, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34

BRAND BUTTON SELECO 74 SHARP 36, 37, 38, 39, 48 SIEMENS 71 SINGER 57 SINUDYNE 57 SONY 35, 48 TELEAVA 73 TELEFUNKEN 67, 73, 75, 76 THOMSON 72, 73, 75 THOMSON ASIA 80, 81 TOSHIBA 47, 48, 49, 50, 51, 52 WEGA 57 YOKO 06 ZENITH 63

Result: If your television is compatible with the remote

control, it will switch off. It is now programmed to operate with the remote control.

■

If several codes are indicated for your

NOTE

television brand, try each one in turn until you find one that works.

■

If you replace the remote control's batteries, you must set the brand code again.

Then you can control the television using the following buttons after pressing the TV button.

Button Function TV STANDBY/ON Used to switch the television on and off.

INPUT Used to select an external source.

TV VOL (+ -) Used to adjust the volume of the television.

PROG ( ) Used to select the desired channel. TV MUTE Used to toggle the sound on and off. Number Used to input number directly.

■

The functions listed above will not necessarily

NOTE

work on all televisions. If you encounter problems, operate the television directly.

14 - English

1 2 3

Description

Front Panel

Getting Started

1. STANDBY/ON BUTTON

Turns the HDD & DVD RECORDER on and off.

2. DVD BUTTON

Select DVD mode.

3. HDD BUTTON

Select HDD mode.

4. DISC TRAY

Opens to accept a disc.

5. DISPLAY

Displays the playing status, time, etc.

6. STOP BUTTON

Stops disc playback.

7. SEARCH/SKIP BUTTONS

Goes to the next title/chapter/track or goes back to the previous title/chapter/track.

Front Panel Display

8. PROG BUTTONS

Select TV preset Channels. Same as

PROG button on the remote control.

9. AV 3 INPUT

Connect external equipment.

10. DV-INPUT

Connect external digital equipment with a DV jack. (such as a camcorder)

11. OPEN/CLOSE BUTTON

Opens and closes the disc tray.

12. PLAY/PAUSE BUTTON

Plays a disc or pauses playback or recording.

13. P.SCAN BUTTON

Selects the progressive scan mode.

14. REC BUTTON

Starts recording.

1. Lights when a disc is loaded.

2. Lights in the record mode.

3. Lights to indicate the timer record mode.

4. Lights when a -R/RW/RAM disc is loaded.

5. Playing time/clock/current status indicator.

6. Lights in the progressive scan mode.

English - 15

Rear Panel

Getting Started

Fan

The fan always revolves when the power is on. Ensure a minimum of 10cm clear space on all sides of the fan when installing the product.

1. DIGITAL AUDIO OUT(OPTICAL)

Connects to an amplifier having a digital optical audio input jack.

2. DIGITAL AUDIO OUT(COAXIAL)

Connects to an amplifier having a digital coaxial audio input jack.

3. AUDIO OUT

Connects to the audio input of external equipment using audio cables.

4. VIDEO OUT

Connects the input of external equipment using a Video cable.

5. S-VIDEO OUT

Connects the input of external equipment using an S-Video cable.

6. COMPONENT VIDEO OUT

Connects to equipment having Component video input.

7. AV1(TV) OUTPUT SCART Connector

8. AV2(EXT) INPUT SCART Connector

9. In from aerial connector

10. Out to TV connector

■

The Antenna connection does not pass the

NOTE

output signal of the DVD. To watch DVD/HDD playback your TV, you must connect audio/video or Scart cables.

16 - English

Tour of the Remote Control

3 4

7 8

9 10 11

12 13

14 15

16 17

18 19

1. DVD STANDBY/ON Button

2. NUMBER Buttons

3. TV/DVD Button

4. DVD Button

Press this to operate DVD.

5. HDD Button

Press this to operate HDD.

6. TV VOL Button

TV volume adjustment

7. REVERSE/FORWARD SKIP Buttons

Press to skip backwards or forwards.

8. REVERSE/FORWARD STEP Buttons

Each press will play one-frame forward or reverse.

9. REVERSE/FORWARD SEARCH Buttons

Press to search a disc backwards or forwards.

10. STOP Button

Press to stop a disc.

11. TITLE LIST/DISC MENU Button

Use this to enter the View Recording list/disc menu.

12. MENU Button

Brings up the HDD & DVD RECORDER’s setup menu.

21 22

23 24

25 26

7 9

27 28

30 31

32 33

34 35

13. OK/DIRECTION Buttons (

…†œ √

Buttons)

14. RETURN Button

15. INFO Button

This will display current setting or disc status.

16. REC Button

Use to make a recording on HDD/DVD-RAM/-RW/-R discs.

17. COPY Button

Press this when you copy DVD to HDD or HDD or viceversa. To start copying, press the

COPY button on the title list

screen or press the COPY button during the playback.

18. REPEAT Button

Allows you to repeat a title, chapter, track or disc.

19. REC PAUSE Button

Use this to pause during recording.

20. TV STANDBY/ON Button

21. AUDIO/TV MUTE Button

Use this to access various audio functions on a disc (DVD mode). In TV mode, this operates as sound mute.

22. INPUT Button

Select input signal in external input mode (

PROG,

AV1,AV2, AV3 or DV input)

23. TV Button

Press this to operate TV.

24. OPEN/CLOSE Button

To open and close the disc tray.

25. CM SKIP Button

When a programme recorded on DVD disc or HDD is played, the unit can be set to automatically skip a portion of the programme.

26. PROG Button

Use this to select a TV programme.

27. PLAY/PAUSE Button

Press to play/pause a disc.

28. PLAY LIST/TITLE MENU Button

Use this to return to the Title menu, or to view the recorded files list.

29. ANYKEY Button

Allows access to common functions of the recorder.

30. CANCEL Button

31. SUBTITLE Button

Press this to switch the DVD’s subtitle language.

32. TIMER Button

Press to directly enter the Timer Recording Mode menu.

33. MARKER Button

Use this to bookmark a position while playing a disc.

34. REPEAT A-B Button

Allows you to repeat a title, chapter, track or disc.

35. REC MODE Button

Use this to set the desired Recording time and picture

(XP/SP/LP/EP)

quality.

English - 17

Getting Started

Connecting & Setting Up

This section involves various methods of connecting the HDD & DVD RECORDER to other external components and required initial setting modes.

Connecting & Setting Up

Quick Overview

A Quick Overview presented in this guide will give you enough information to start using the HDD & DVD RECORDER.

Connecting the HDD & DVD RECORDER

†

Additional connections

†

Antenna + HDD & DVD RECORDER + External decoder box + TV

†

Other type of connecting the Video output cable

Quick Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Connecting the HDD & DVD RECORDER . . . . . .19

Additional connections . . . . . . . . . . . . . . . . . . . . . .19

Antenna + HDD & DVD RECORDER +

External decoder box + TV . . . . . . . . . . . . . . . . . .20

Other type of connecting the Video output cable . .20

Other type of connecting the Audio output cable . .22

Connecting to AV 3 IN, DV input jack . . . . . . . . . .24

†

Other type of connecting the Audio output cable

†

Connecting to AV 3 IN, DV input jack

18 - English

Connecting the

HDD & DVD RECORDER

Additional connections

You can connect your HDD & DVD RECORDER to the television using the SCART cable if the appropriate input is available on the television.

1. Connect the RF cable as shown.

2. Connect one end of the SCART cable to the AV1 socket on the rear of the HDD & DVD RECORDER.

3. Plug the other end into the appropriate connector on the television.

4. Plug in the HDD & DVD RECORDER and TV

5. Turn on the HDD & DVD RECORDER and TV.

6. Press the until the Video signal from the HDD & DVD RECORDER appears on the TV screen.

INPUT button on your TV remote control

To RF IN

You can connect your HDD & DVD RECORDER to a satellite or digital tuner.

external device (VCR/Satellite receiver)

Connecting & Setting Up

To TV

RF Cable

To ANT INPUT

■

The RF cable connection of this product

NOTE

sends only signals of TV. You must connect SCART cable or Audio/Video cables to watch a DVD from your HDD & DVD RECORDER.

■

TV mode Press the TV/DVD button on remote control, then “TV” appear on Front LED display (or turn off HDD & DVD RECORDER). Then you can watch programmes received through RF cable.

- DVD mode

1. Connect the AV2 connector of HDD & DVD RECORDER and VCR/Satellite receiver or digital tuner using a SCART cable.

2. Connect the AV1 connector to the SCART AV connector on TV.

3. Turn on the HDD & DVD RECORDER, VCR/Satellite receiver or digital tuner and TV.

4. Set Input mode on AV2.

- TV mode

1. Press the “TV” appear on Front LED display. (or turn off HDD & DVD RECORDER.)

2. You can watch programmes from a satellite or digital tuner connected to this HDD & DVD RECORDER, even when the HDD & DVD RECORDER is turned off.

TV/DVD button on remote control,then

English - 19

Antenna + HDD & DVD

Other type of connecting

RECORDER + External decoder box + TV

If you connect external decoder box to HDD & DVD RECORDER, you can record scrambled channels (CANAL+or Premiere broadcasts) received through the built-in TV tuner in HDD & DVD RECORDER.

Wall

Connecting & Setting Up

DECODER

the Video output cable

There are several ways to output video signal not using scart cables. Select one of the following video connecting that best suits you below.

•

Case 1 : Connecting to a Video (Composite) output

•

Case 2 : Connecting to an S-Video output jack

•

Case 3 : Component Video output jacks

S-Video, Component video and Progressive Output Modes

•

S-Video and Component video output are available only if your TV supports S-Video input or Component video input, respectively. If S-Video or Component video output does not work, check the TV connections and the TV input selection settings.

•

Compared to standard interlaced video, progressive scan doubles the amount of video lines fed to your TV, resulting in a more stable, flickerfree, clear image than interlaced video. This is only available with TVs that support progressive scan.

•

Progressive Scan Output (576p) Consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture, in case of 576 progressive scan picture problems, It is recommended that the user switch the connection to the ‘standard definition’ output. If there are questions regarding our TV set compatibility with this model 576p HDD & DVD RECORDER, please contact our customer service centre.

jack

1. Connect RF antenna cables as shown.

2. Connect the AV1 connector on this recorder to the SCART AV connector on TV using a SCART cable.

3. Connect the AV2 connector to a SCART AV connector on decoder box.

4. To watch or record PAY-TV Canal Plus programmes, set your HDD & DVD RECORDER to receive the channels using the on-screen display.(Refer to page 30)

20 - English

Case 1 : Connecting to a Video (Composite) output jack

Case 2 : Connecting to an S-Video output jack

1. Connect a video(yellow) cable between the VIDEO (yellow) OUT jack on HDD & DVD RECORDER and VIDEO (yellow) INPUT jack on your TV (or AV amplifier).

•

Case 3 : Component Video output jacks

Other type of connecting

1. Connect Component video cables(not supplied) between the COMPONENT OUT(Y,P

B,PR

HDD & DVD RECORDER and COMPONENT IN(Y,PB,PR) jacks on your TV.

•

You will enjoy high quality and accurate colour reproduction images.

2. Connect audio cables (white and red) between the AUDIO OUT jacks on the HDD & DVD RECORDER and AUDIO IN jacks on TV (or AV amplifier). (See pages 22~23).

3. After connecting, refer to the pages 41~43.

Connecting & Setting Up

) jacks on

the Audio output cable

There are several ways to output audio signal not using scart cables. Select the audio connection that best suits you below.

•

Case 1 : Connecting to your TV

•

Case 2 : Connecting to a stereo amplifier with AV

•

Case 3 : Connecting to an AV amplifier with a

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.

output jacks

digital output jack

NOTE

blue

red

green

blue

red

■

Make sure that the colour coded connections match. The Y, P

, P

component output jacks of your HDD & DVD RECORDER must be connected to the exact corresponding component input jacks on your TV.

■

Progressive setting is only available when the Video Out is set to Component. (See pages 41~43)

green

Case 1 : Connecting to your TV

If your TV has audio input jacks, use this connection.

yellow

white

red

yellow

white

red

22 - English

Case 2 : Connecting to a stereo amplifier with AV output jacks

Case 3: Connecting to an AV amplifier with a digital output jack

If your stereo amplifier only has AUDIO INPUT jacks(L and R), use the AUDIO OUT jacks.

whitered

If your AV amplifier has a Dolby Digital, MPEG2 or DTS decoder and a digital input jack, use this connection. To enjoy Dolby Digital, MPEG2 or DTS sound, you will need to set up the audio settings. (See page 39)

Connecting & Setting Up

Front(L) speaker

Front(R) speaker

Rear(L)

Front(L)

Rear(R)

Front(R)

Subwoofer Centre

English - 23

Connecting to AV 3 IN,

Case 2 : Connecting a Camcorder to the DV IN jack

DV input jack

This allows you to connect your HDD & DVD RECORDER to other external devices and view or record their outputs.

•

Case 1 :

•

Case2 : Connecting a DV Device to the DV IN jack

Connecting & Setting Up

Connecting a VCR or external device to AV3 IN jacks of the HDD & DVD RECORDER. You can record from connected equipment (VCR, STB, DVD player or Camcorder).

Connecting a VCR, Set-Top Box(STB), DVD player or Camcorder to the AV3 IN jacks

Case 1 : Connecting a VCR, Set-Top Box(STB), DVD player or Camcorder

to the AV3 IN jacks

If your digital camcorder has a DV output jack, connect it to the DV input jack of your HDD & DVD RECORDER.

Camcorder

■

If the input is not selected automatically,

NOTE

use INPUT button to select proper input.

NOTE

Camcorder

VCR

yellow

white

STB

DVD

yellow

white

red

■

AV 3 in selection will be automatically done. If the input is not selected automatically, use proper input.

■

Copy protected content cannot be recorded.

INPUT button to select

red

24 - English

On-Screen Menu

System Setup

On-Screen Menu Navigation . . . . . . . . . . . . . . . . .25

Plug & Auto Setup . . . . . . . . . . . . . . . . . . . . . . . . .26

Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . .27

Presetting Channels with the Auto Setup

function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Presetting Channels with the Manual Setup

function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Navigation

The on-screen menus allow you to enable or disable various functions on your HDD & DVD RECORDER. Use the following buttons to open and navigate through the on-screen menus.

HDD

System

Title

Clock Set

Music

Language Audio

Photo

Video Parental Control

Programme

Install

Setup

MOVE SELECT RETURN EXIT

MENU Button

Press this button on the remote control to open the on-screen menu. Press again to exit the on-screen menu.

…†, œ√ Buttons

Press these buttons on remote control to move the selection bar menu options.

…†, œ √ to cycle through the

Setup

√√

System Setup

Setting up the Language Options . . . . . . . . . . . . .31

Auto Power Off Setting . . . . . . . . . . . . . . . . . . . . .32

CM Skip Time Setting . . . . . . . . . . . . . . . . . . . . . .33

EP Mode Time Setting . . . . . . . . . . . . . . . . . . . . .34

Setting up the Front Display Options . . . . . . . . . . .35

Automatic Chapter Creator . . . . . . . . . . . . . . . . . .36

Setting up NICAM Options . . . . . . . . . . . . . . . . . .37

DivX(R) Registration . . . . . . . . . . . . . . . . . . . . . . .38

Setting up the Audio Options . . . . . . . . . . . . . . . . .38

Setting up the Video display Options . . . . . . . . . . .40

Setting up Video Output Options . . . . . . . . . . . . . .41

Setting up the Progressive scan . . . . . . . . . . . . . .42

Canceling the Progressive scan . . . . . . . . . . . . . .43

Setting up the Parental Control . . . . . . . . . . . . . . .44

OK Button

Press this button on the remote control to confirm any new settings.

RETURN Button

Press this button on the remote control to return to the Previous menu screen displayed or to exit the on-screen menu.

English - 25

Plug & Auto Setup

Your HDD & DVD RECORDER will automatically set itself up when it is plugged in for the first time. TV stations and clock will be stored in memory. The process takes a few minutes. Your HDD & DVD RECORDER will then be ready for use.

Connect the RF cable as indicated on page 19. (Connecting Your HDD & DVD RECORDER to the

TV Using the RF Cable and scart cable.)

Plug the HDD & DVD RECORDER into the mains. “AUTO” in the front panel display flickers.

System Setup

Press a number button to select the language.

Select “Country” using the …† œ √ buttons to select your country.

Country Selection

ANLSPL

BICHCZ DK N TR Others FIN P GR

DEHU

•

Refer to following abbreviation table when selecting “Country”.

A(Austria) NL(Netherlands) S(Sweden) PL(Poland)

B(Belgium) I(Italy) CH(Swiss) CZ (Czech)

DK(Denmark) N(Norway) TR(Turkey) Others

FIN(Finland) P(Portugal) GR(Greece)

D(Deutschland) E(Spain) HU(Hungary)

•

The HDD & DVD RECORDER searches for the stations according to a preset preference list corresponding to the country that you have selected.

Auto channel scan will be started.

Press 1 for English

Touche 2 pour Français

Drücken Sie 3 Für Deutsch

Pulse 4 para Español Premere 5 per Italiano Druk op 6 voor Nederlands

Press the OK button to start the auto setup.

Auto setup will be started.

Check antenna and TV cable connection.

Yes No

Channel Scan

Scanning...

10%

•

The number of stations automatically stored by the HDD & DVD RECORDER depends on the number of stations that it has found.

After auto channel scan is completed, auto clock setting will be started automatically in 10 seconds.

If you want to start auto clock setting immediately, press

OK button. If you do not want to do auto

clock setting, press

Auto channel scan completed successfully.

Press the [OK] button to auto clock set.

CANCEL or MENU button.

Yes No

26 - English

Wait until current date and time are displayed automatically. If you want to exit auto clock setting,

press

MENU button.

Please wait. Now setting the clock.

If you want to exit clock setting,

press the [MENU] button.

Setting the Clock

This menu is used to set the current time. You need to set the time to use timer recording.

With the unit in Stop mode, press the MENU

button

Check the date and time.

Time

12 : 00 01 / JAN SAT 2005 On

• if it is : Correct, press and time will be saved. If you don't press the button, the date and time will be saved automatically after 5 seconds.

• if it is : Incorrect, input correct Time, Date, Year

using …†œ √ buttons or number buttons. Press

OK button then the date and time will be

saved. When you need to change clock setting, you can set up it manually.

■

Now, HDD & DVD RECORDER is ready

NOTE

for use. Function for “Plug & Auto Setup” is fixed already. So if you want to change this fixed one, you can change it by Presetting the Stations in OSD “Presetting Channels with the Manual setup function” menu. (See page 30)

■

Auto setup function can be performed by pressing

continuously for 5 seconds or more during power off with no disc inserted.

Date Auto clock

OK button then the date

STOP ( ) on the unit

HDD

Title

Title List

Music

Photo

Programme

Setup

MOVE SELECT RETURN EXIT

Title

√√

Press the …† buttons to select Setup, then press the

OK or √ button.

HDD

System

Title

Clock Set

Music

Language Audio

Photo

Video Parental Control

Programme

Install

Setup

MOVE SELECT RETURN EXIT

Setup

√√

Press the …† buttons to select Clock Set, then press the

Press the

OK or √ button.

…†œ √ buttons to input Time, Date or

Year. Press the number buttons to input clock data directly. The day of the week is displayed automatically.

HDD

Title

Time Date

Music

12 : 00 01 / JAN SAT 2005 On

Photo

Programme

Setup

0~9 NUMBER SELECT RETURN EXIT

Clock Set

Auto Clock

System Setup

English - 27

Press the …† buttons to select On for the Auto Clock.

HDD Title

Time Date

Music

12 : 00 01 / JAN SAT 2005 On

Photo

Programme

Setup

0~9 NUMBER SELECT RETURN EXIT

Clock Set

Auto Clock

Presetting Channels with the Auto Setup function

This feature allows you to manually set the HDD & DVD RECORDER tuner band to Antenna or Cable, whichever you connected to the Antenna In jack during initial setup.

Press the OK button, then the date and time will be saved. If you don’t press the

not be saved.

■

System Setup

NOTE

You must have the RF cable connected to set the Auto Clock. (See page 19)

■

The HDD & DVD RECORDER automatically sets the clock according to the time signal broadcast between the channels PR1 to PR5. If you do not need the auto clock set function, select Off.

OK button, it will

With the unit in Stop mode, press the MENU

button

Press the …† buttons to select Setup, then press the

OK or √ button.

HDD

System

Title

Clock Set

Music

Language Audio

Photo

Video Parental Control

Programme

Install

Setup

MOVE SELECT RETURN EXIT

Setup

√√

Press the …† buttons to select Install, then press the

OK or √ button.

HDD

Auto Setup

Title

Manual Setup

Music

Photo

Programme

Setup

MOVE SELECT RETURN EXIT

Install

√√

28 - English

Press the …† buttons to select Auto Setup, then

press the

OK or √ button.

The message “Your data will be lost. Press [OK] to continue, [Return] to exit.” is displayed.

HDD

Title

Music

Your data will be lost.

Press [OK] to continue, [Return] to exit.

Photo

Programme

Setup

SELECT RETURN EXIT

Install

Press the OK button, then press the …†œ √

buttons to select your Country.

The HDD & DVD RECORDER searches for the

• stations according to a preset preference list corresponding to the country that you have selected.

• The first frequency band is scanned and the first station found is displayed and stored. And the HDD & DVD RECORDER searches for the second station and so on.

• When the automatic scanning procedure has finished, the HDD & DVD RECORDER switches automatically to programme 1.

• The number of stations automatically stored by the HDD & DVD RECORDER depends on the number of stations that it has found.

Channel scan will be started. Press the OK button to stop the Auto Setup.

System Setup

HDD

Country Selection

Title

ANLSPL

Music

BICHCZ

DK N TR Others

Photo

FIN P GR

Programme

DEHU

Setup

MOVE SELECT RETURN EXIT

Install

Refer to following table when selecting your country.

A(Austria) NL(Netherlands) S(Sweden) PL(Poland)

B(Belgium) I(Italy) CH(Swiss) CZ (Czech)

DK(Denmark) N(Norway) TR(Turkey) Others

FIN(Finland) P(Portugal) GR(Greece)

D(Deutschland) E(Spain) HU(Hungary)

Press the OK button. If you want to exit, press the

MENU button.

HDD

Title

Music

Photo

Programme

Setup

Please wait.

Scanning...

SELECT RETURN EXIT

Auto Setup

11%

Stop

English - 29

Presetting Channels with

the Manual Setup function

Press the …† buttons to select a PR(programme) you wish to edit, delete, or swap, then press the ANYKEY button. Select

Edit, Delete or Swap.

You can add preset channel that Auto Channel Search missed. And you can delete a channel you wish to remove. You can programme the order of channels.

With the unit in Stop mode, press the MENU

button.

Press the

the

System Setup

Press the

press the

…†

buttons to select Setup, then press

OK or √ button.

HDD

System

Title

Clock Set

Music

Language Audio

Photo

Video Parental Control

Programme

Install

Setup

MOVE SELECT RETURN EXIT

…†

buttons to select Install, then

OK or √ button.

HDD

Auto Setup

Title

Manual Setup

Music

Photo

Programme

Setup

MOVE SELECT RETURN EXIT

Setup

Install

√√

Manual Setup

PR CH Name Decoder 01 - - - - - - - - 02 - - - - - - - - 03 - - - - - - - - 04 - - - - - - - - -

Edit

05 - - - - - - - - 06 - - - - - - - - -

Delete

07 - - - - - - - - -

Swap

MOVE SELECT RETURN EXIT

•

In case of Edit : You can add or edit PR(programme) information. After change PR informations(

CH, Name, Decoder, MFT), select

Save, then press the OK button.

Manual Setup

PR 01 CH 02 Name - - - Decoder Off MFT - - - - - -

CH : Tune the channel using œ √ buttons.

Name : Display station name automatically detected

Save

MOVE SELECT

in broadcasting signal. If not detected, you can edit name by using

Decoder : If you set on, you can record scrambled

…†œ √ buttons.

channels using external decoder box. Before setting on, refer to connecting external decoder box in the page 20.

MFT(Manual Frequency Tunning) : You can tune up the channel frequency better using

œ √ buttons.

Press the then press the

Manual Setup

30 - English

…†

buttons to select Manual Setup, OK or √ button.

PR CH Name Decoder 01 - - - - - - - - 02 - - - - - - - - 03 - - - - - - - - 04 - - - - - - - - 05 - - - - - - - - 06 - - - - - - - - 07 - - - - - - - - -

MOVE SELECT RETURN EXIT

In case of Delete : the channel information of

• selected PR(programme) will be removed.

In case of Swap : You can swap the channel

• information of two PR(programme). For example, if you wish to swap PR2 and PR5, select swap at PR2, then press the

OK button at PR5.

+ 102 hidden pages