Samsung DVD-HD960-XAA User Manual

DVD Player

DVD-HD960

www.samsung.com

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings, Install in accordance with the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat registers, or other apparatus (including

amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has two blades and a third grounding prong.

The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus.

13) Unplug this apparatus. When a cart is used, use caution when moving the

cart/apparatus combination to avoid injury from tip-over.

14) Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture, does

not operate normally, or has been dropped.

ENG-2

Precautions

RISK OF ELECTRIC SHOCK

DO NOT OPEN

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates “dangerous voltage” inside the product that presents a risk of electric shock or

This symbol indicates important instructions accompanying the product.

personal injury.

Do not install this equipment in a confined space such as a bookcase or similar unit.

WARNING : To prevent damage which may result in fire or electric shock hazard, do not expose

this appliance to rain or moisture.

Note to CATV system installer : This reminder is provided to call CATV system installer’s attention to Article 820-40 of the National Electrical Code (Section 54 of Canadian Electrical Code, Part I) that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. Caution : FCC regulations state that any unauthorized changes or modifications to this equipment may void the user’s authority to operate it.

FCC NOTE (for U.S.A):

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures.

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect this equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This class B digital apparatus meets all requirements of the Canadian Interference --

Causing Equipment Regulations.

CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT PRODUCTO LÁSER CLASE 1

ENG-3

CAUTION

THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVER AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

Note:

• This unit can be used only where the power supply is AC 120V, 60Hz. It cannot be used elsewhere.

• This DVD player is designed and manufactured to respond to the Region Management Information.

If the Region number of a DVD disc does not correspond to the Region number of this DVD player, the DVD player cannot play the disc.

Handling Cautions

• Before connecting other components to this player, be sure to turn them all off.

• Do not move the player while a disc is being played, or the disc may be scratched or broken, and the player’s

internal parts may be damaged.

• Do not put a flower vase filled with water or any small metal objects on the player.

• Be careful not to put your hand into the disc tray.

• Do not place anything other than the disc in the disc tray.

• Exterior interference such as lightning and static electricity can affect normal operation of this player.

If this occurs, turn the player off and on again with the POWER button, or disconnect and then reconnect the AC power cord to the AC power outlet. The player will operate normally.

• Be sure to remove the disc and turn off the player after use.

• Disconnect the AC power cord from the AC outlet when you don’t intend to use the player for long

periods of time.

• Clean the disc by wiping in a straight line from the inside to the outside of the disc.

Disc Storage

Be careful not to harm the disc because the data on these discs is highly vulnerable to the environment.

• Do not keep under direct sunlight.

• Keep in a cool ventilated area.

• Store vertically.

• Keep in a clean protection jacket.

Maintenance of Cabinet

For safety reasons, be sure to disconnect the AC power cord from the AC outlet.

• Do not use benzene, thinner, or other solvents for cleaning.

• Wipe the cabinet with a soft cloth.

ENG-4

Before you start

Accessories

Remote

Control

(AK59-00055D)

Batteries for Remote

Control (AAA Size)

(AC43-12002H)

Install Batteries in the Remote control

Open the battery cover on the back of the remote control.

Insert two AAA batteries. Make sure that the polarities (+ and -) are aligned correctly.

User’s Manual

(AK68-01038A)

Video/Audio

Cable

(AC39-42001R)

HDMI Cable

(MF39-00299A)

Replace the battery cover.

If the remote control doesn’t operate properly:

- Check the polarity + - of the batteries (Dry-Cell)

- Check if the batteries are drained.

- Check if remote control sensor is blocked by obstacles.

- Check if there is any fluorescent lighting nearby.

ENG-5

TABLE OF CONTENTS

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Chapter 1:

Chapter 2: Connections

Chapter 3: Basic Functions

Chapter 4: Advanced Functions

Chapter 5: Changing Setup Menu

Chapter 6: Reference

Setup

General Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Disc Type and Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Tour of the Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Choosing a Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Using the Search and Skip Functions . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Using the Display Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Using the Disc and Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Using the Function Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Adjusting the Aspect Ratio (EZ View) . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Selecting the Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Selecting the Subtitle Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Changing the Camera Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Using the Instant Replay/Skip Function . . . . . . . . . . . . . . . . . . . . . . . . . 33

Using the Bookmark Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Using the Zoom Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Clips Menu for MP3/WMA/JPEG/MPEG4/CD Audio . . . . . . . . . . . . . . . 37

Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

MP3/WMA/CD Audio Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Picture CD Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Using the Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Setting Up the Language Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Setting Up the Audio Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Setting Up the Display Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Setting Up the Parental Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Controlling a TV with the Remote control . . . . . . . . . . . . . . . . . . . . . . . . 58

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

ENG-6

Chapter 1

SETUP

General Features

Excellent Sound

Dolby Digital, a technology developed by Dolby Laboratories, provides crystal clear sound reproduction.

Screen

Both regular and widescreen(16:9) pictures can be viewed.

Slow Motion

An important scene can be viewed in slow motion.

Parental Control (DVD)

The parental control allows users to set the level necessary to prohibit children from viewing harmful movies such as those with violence, adult subject matter, etc.

Various On-Screen Menu Functions

You can select various languages (Audio/Subtitle) and screen angles while enjoying movies.

Progressive Scan

Progressive scanning creates an improved picture with double the scan lines of a conventional interlaced picture.

EZ VIEW (DVD)

Easy View enables picture adjustment to match your TV's screen size (16:9 or 4:3).

Digital Photo Viewer (JPEG)

You can view Digital Photos on your TV.

Repeat

You can repeat a song or movie simply by pressing the REPEAT button.

MP3/WMA

This unit can play discs created from MP3/WMA files.

Instant Replay (DVD)

This function is used to replay the previous 10 seconds of a movie from the current position.

Instant Skip (DVD)

This function skips playback ahead 10 seconds.

MPEG4

This unit can play MPEG4 formats within an avi file.

HDMI (High Definition Multimedia Interface)

HDMI reduces picture noise by allowing a pure digital video/audio signal path from the player to your TV.

ENG-7

Setup

Note

- Discs which cannot be played with this player.

• DVD-ROM • DVD-RAM

• CD-ROM • CDV

• CDI • CVD

• Super Audio CD(except CD layer)

• CDGs play audio only, not graphics.

- Ability to play back may depend on recording conditions.

• DVD-R, +R

• CD-RW

• DVD+RW, -RW (V mode)

- The unit may not play certain CD-R, CD-RW and DVD-R due to the disc type or recording conditions.

COPY PROTECTION

Many DVD discs are encoded with copy protection. Because of this, you should only connect your DVD player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy-protected DVD discs.

This product incorporates copyright protection technology that is protected by methods claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

PROGRESSIVE SCAN OUTPUTS (525p)

“CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE, IF 525 PROGRESSIVE SCAN PICTURE PROBLEMS OCCUR, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS REGARDING YOUR TV SET COMPATIBILITY WITH THIS DVD PLAYER, PLEASE CONTACT SAMSUNG'S CUSTOMER SERVICE CENTER.”

SETUP

Disc Type and Characteristics

This DVD player is capable of playing the following types of discs with the corresponding logos:

Disc Types (Logos)

DVD

AUDIO-CD

Recording Types Disc Size Max. Playing Time Characteristics

- DVD contains excellent sound and video due to Dolby Digital and MPEG-2 system.

-Various screen and audio functions can be easily selected through the on-screen menu.

- CD is recorded as a Digital Signal with

better audio quality, less distortion and less deterioration of audio quality over time.

Audio

Video

Audio

5”

3 1/2”

5”

3 1/2”

Single-sided 240 min.

Double-sided 480 min.

Single-sided 80 min.

Double-sided 160 min.

74 min.

20 min.

Disc Markings Region Number

NTSC

STEREO

DIGITAL

SOUND

Play Region Number

NTSC broadcast system in U.S.A, Canada, Korea, Japan, etc.

Dolby Digital disc

Stereo disc

Digital Audio disc

DTS disc

Both the DVD player and the discs are

coded by region. These regional codes must match in order for the disc to play. If the codes do not match, the disc will not play.

The Region Number for this player is described on the rear panel of the player.

DivX Trademark Info

MP3 disc

DivX, DivX Certified, and

associated logos are

You must only insert one DVD disc at a time.

Inserting two or more discs will not allow playback and may cause damage to the DVD

trademarks of DivXNetworks, Inc and are used under license.

player.

ENG-8

VIDEO SEL.

OPEN/CLOSE

Description

Front Panel Controls

SETUP

Setup

1. STANDBY/ON ( )

When STANDBY/ON is pressed on, the indicator goes out and the player is turned on.

2. STANDBY Indicator

When the unit is first plugged in, the indicator lights.

3. DISC TRAY

Place the disc here.

4. OPEN/CLOSE ( )

Press to open and close the disc tray.

5. DISPLAY

Operation indicators are displayed here.

Front Panel Display

1 23

1. Disc type indicators

2. Play / Pause

6. VIDEO SEL.

Press to change Video output mode (Progressive ON or Progressive OFF).

7. STOP ( )

Stops disc play.

8. SKIP ( ) / SEARCH

Use to forward skip a scene or music.

9. SKIP ( ) / SEARCH

Use to reverse skip a scene or music.

10. PLAY/PAUSE ( )

Begin or pause disc play.

3. Displays various messages concerning operations such as PLAY, STOP, LOAD ...

no DISC: No disc loaded. OPEN: The disc tray is open. LOAD: Player is loading disc information.

ENG-9

Rear Panel

SETUP

13 45 6

1. DIGITAL AUDIO OUT JACKS

- Use either an optical or coaxial digital cable to connect to a compatible Dolby Digital receiver.

- Use either an optical or coaxial digital cable to connect to an A/V Amplifier that contains a Dolby Digital, MPEG2 or DTS decoder.

2. COMPONENT VIDEO OUT JACKS

- Use these jacks if you have a TV with Component Video in jacks. These jacks provide PR, PBand Y video.

- If Progressive Out is set to ON in the Video Output of the Setup Menu, progressive scan mode will be output.

- If Progressive Out is set to OFF in the Video Output of the Setup Menu, interlaced scan video will be output.

3. AUDIO OUT JACKS

Connect to the Audio input jacks of your television or audio/video receiver

4. VIDEO OUT JACK

- Use a video cable to connect to the Video input jack on your television.

5. S-VIDEO OUT JACK

- Use the S-Video cable to connect this jack to the S-Video jack on your television for higher picture quality.

6. HDMI OUT JACK

- Use the HDMI cable to connect this jack to the HDMI jack on your television for the best quality picture.

- If an HDMI cable is connected to an HDMI-compatible TV, HDMI will be output automatically a maximum of 10 seconds later.

Note

Consult your TV User’s Manual to find out if your TV supports Progressive Scan (P-SCAN). If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s menu system.

- If Progressive Out On Video Output is selected in Setup Menu, Video and S-Video Outputs do not work.

- The HDMI output of this unit can be connected to a DVI jack on a TV or other device using a conversion

adapter. In this case, it is necessary to use a TV or display with an HDCP-compatible DVI input.

- There may be no image output if the DVD player is connected to a TV or display that is not compatible with

the above format.

- Refer to your TV's instruction manual for detailed information regarding the HDMI terminal.

- See pages 52 ~ 54 to get more information on how to use the setup menu.

ENG-10

SETUP

Tour of the Remote Control

1 2

6 7

8 9

15 16

1. VIDEO SEL. Button

Selects video output formats

2. HDMI SEL. Button

HDMI Output resolution setup.

3. DVD POWER Button

Turns the power on or off.

4. NUMBER Buttons

5. BOOKMARK Button

6. SEARCH Buttons (

Allow you to search forward/backward through a disc.

7. INSTANT REPLAY Button

17 18

19 20

25 26

27 28

29 30

This function is used to replay the previous 10 seconds of a movie from the current position.

8 SKIP Buttons (

Use to skip the title, chapter or track.

9. STOP Button ( )

10. VOL (+, -) Buttons

Control volume.

11. MENU Button

Brings up the DVD player’s menu.

12. ENTER/

This button functions as a toggle switch.

13. EZ VIEW Button

The aspect ratio of a picture can easily be adjusted according to the screen size of your TV (16:9 or 4:3).

14. DISC MENU Button

Brings up the Disc menu.

15. SUBTITLE Button

16. AUDIO Button

Use this button to access various audio functions on a disc.

17. REPEAT A-B Button

Allows you to repeat play A-B on a disc.

18. REPEAT Button

Allows you to repeat play a title, chapter, track, or disc.

19. TV POWER Button

Turns the TV’s power on or off.

20. OPEN/CLOSE ( ) Button

To open and close the disc tray.

21. STEP Button

Advances play one frame at a time.

22. INSTANT SKIP Button

This function skips playback ahead 10 seconds.

23. PLAY/PAUSE Button ( )

Begin/Pause disc play.

24. CH ( , ) Buttons

Channel selection.

25. TV/VIDEO Button

Press to display all of the available video sources ( i.e., TV, Cable, Video)

26. RETURN Button

Returns to a previous menu.

27. INFO Button

Displays the current disc mode.

28. CANCEL Button

Use to remove menus or status displays from the screen.

29. ZOOM Button

Enlarges the DVD Picture

30. ANGLE Button

Use to access various camera angles on a DVD.

/❷❷,➛➛/❿❿

)

Buttons

Setup

)

ENG-11

Chapter 2

CONNECTIONS

Choosing a Connection

The following shows examples of connections commonly used to connect the DVD player with a TV and other components.

Before Connecting the DVD Player

- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.

- Refer to the user’s manual of the additional components (such as a TV) you are connecting for more information on those particular components.

Connection to a TV (Video)

Using video/audio cables, connect the VIDEO (yellow)/AUDIO (red and white) OUT terminals on the rear of the DVD player to

the VIDEO (yellow)/AUDIO (red and white) IN terminals of your TV.

Turn on the DVD player and TV.

Press the input selector on your TV remote control until the Video signal from the DVD player appears on the TV screen.

RED

WHITE

Audio Cable

WHITE

YELLOW

Video Cable

YELLOW

You can also use the VIDEO SEL. button to change the Video Output mode. (See page 12)

Note

- Noise may be generated if the audio cable is placed too close to the power cable.

- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 18 to 19)

- The number and position of terminals may vary depending on your TV set. Please refer to the user's manual of your TV.

- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of the DVD player.

- If you press the VIDEO SEL. button when DVD Player is in stop mode or no disc is inserted, the Video Output mode changes in the following sequence: (Progressive : ON

➝ Progressive : OFF).

ENG-12

CONNECTIONS

Connection to a TV (S-Video)

- Connecting to your TV using an S-Video cable.

- You will enjoy high quality images. S-Video separates the picture element into black and white(Y) and color(C) signals to present clearer images than regular video input mode. (Audio signals are delivered through the audio output.)

Using an S-Video cable (not included), connect the S-VIDEO OUT terminal on the rear of the DVD player to the S-VIDEO IN terminal of your TV.

Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of your TV.

Turn on the DVD player and TV.

Connections

Press the input selector on your TV remote control until the SVideo signal from the DVD player appears on your TV screen.

RED

WHITE

Audio Cable

RED

WHITE

S-Video Cable (not included)

Set the Video Output to Progessive Out Off in the Display Setup menu. (See pages 52 to 54) You can use the VIDEO SEL. button to change the Video Output mode. (See page 12)

Note

- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 18 to 19)

- The number and position of terminals may vary depending on the TV set. Please refer to the user's manual of your TV.

ENG-13

CONNECTIONS

Connection to a TV (Interlace)

- Connecting to your TV using Component video cables.

- You will enjoy high quality and accurate color reproduction images. Component video separates the picture element into black and white(Y), blue(PB), red(PR) signals to present clear and clean images. (Audio signals are delivered through the audio output.)

Using component video cables (not included), connect the COMPONENT VIDEO OUT terminals on the rear of the DVD player to the COMPONENT IN terminals of your TV.

Using the audio cables, connect the AUDIO (red and white)

RED

BLUE

GREEN

OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of your TV.

Turn on the DVD player and TV.

Audio Cable

WHITE

RED

WHITE

Component cable

RED

BLUE

GREEN

(not included)

Press the input selector on your TV remote control until the Component signal from the DVD player appears on the TV screen.

RED

Set the Video Output to Progressive Out Off in the Display Setup menu. (See pages 52 to 54) You can use the VIDEO SEL. button to change the Video Output mode. (See page 12)

Note

- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 18 to 19)

- The component terminal of your TV may be marked “R-Y, B-Y, Y” or “Cr, Cb, Y” instead of “P depending on the manufacturer. The number and position of terminals may vary depending on the TV set. Please refer to the user's manual of your TV.

, PB, Y”

ENG-14

CONNECTIONS

Connection to a TV (Progressive)

Using component video cables (not included), connect the COMPONENT VIDEO OUT terminals on the rear of the DVD player to the COMPONENT IN terminals of your TV.

Connections

Using the audio cables, connect the AUDIO (red and white)

RED

BLUE

GREEN

OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of your TV.

Turn on the DVD player and TV.

Audio Cable

WHITE

RED

WHITE

Component cable

RED

BLUE

GREEN

(not included)

Press the input selector on your TV remote control until the Component signal from the DVD player appears on the TV screen.

RED

Set the Video Output to Progressive Out ON in the Display Setup menu. (See pages 52 to 54) You can use the VIDEO SEL. button to change the Video Output mode. (See page 12)

To see the progressive video output,

- Consult your TV User’s Manual to find out if your TV supports Progressive Scan. If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s menu system.

- Depending on your TV, the connection method may differ from the illustration above.

Note

- What is "Progressive Scan"? Progressive scan has twice as many scanning lines as the interlace output method. Progressive scanning method provides better and clearer picture quality.

ENG-15

CONNECTIONS

Connecting to a TV with DVI Jack

Using the HDMI-DVI cable (not included), connect the HDMI OUT terminal on the rear of the DVD player to the DVI IN

terminal of your TV.

Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of your TV.

Turn on the DVD player and TV.

Press the input selector on your TV remote control until the DVI signal from the DVD player appears on your TV screen.

RED

WHITE

Audio Cable

WHITE

HDMI-DVI cable (Not Included)

Connecting to a TV with HDMI Jack

Using the HDMI-HDMI cable connect the HDMI OUT terminal on the rear of the DVD player to the HDMI IN terminal of your TV.

Press the input selector on your TV remote control until the HDMI signal from the DVD player appears on your TV screen.

HDMI VIDEO Specifications

When you press the HDMI SEL. button, 480p, 720p, 1080i and 1080p are selected in order. The first press of the

HDMI SEL. button brings up the current resolution.

The second press changes the HDMI output resolution to the next setting.

- Depending on your TV, certain HDMI output resolutions may not work.

- Please refer to the user's manual of your TV.

- If HDMI or HDMI-DVI cable is plugged into TV, the DVD player’s output is set to HDMI/DVI automatically

about 10 seconds later.

- For better picture quality, set the HDMI output resolution to 720p or 1080i/1080p.

- If your TV cannot support the HDMI resolution you selected, the resolution is set to 480p automatically.

HDMI cable

ENG-16

CONNECTIONS

• HDMI (High Definition Multimedia Interface)

HDMI is an interface to enable the digital transmission of video and audio data with just a single connector. Using HDMI, the DVD player transmits a digital video and audio signal and displays a vivid picture on a TV having an HDMI input jack.

• HDMI connection description

HDMI connector - Both uncompressed video data and digital audio data (LPCM or Bit Stream data).

- Though the player uses a HDMI cable, the player outputs only a pure digital signal to the TV.

- If TV does not support HDCP (High-bandwidth Digital content protection), snow noise appears on the screen.

• Why does Samsung use HDMI?

Analog TVs require an analog video/audio signal. However, when playing a DVD, the data transmitted to a TV is digital. Therefore either a digital-to-analog converter (in the DVD player) or an analog-to-digital converter (in the TV) is required. During this conversion, the picture quality is degraded due to noise and signal loss. HDMI technology is superior because it requires no D/A, A/D conversion and is a pure digital signal from the player to your TV.

• What is the HDCP?

HDCP (High-bandwidth Digital Content Protection) is a system for protecting DVD content outputted via DVI from being copied. It provides a secure digital link between a video source (PC, DVD. etc) and a display device (TV, projector . etc). Content is encrypted at the source device to prevent unauthorized copies from being made.

Connections

ENG-17

CONNECTIONS

Connection to an Audio System (2 Channel Amplifier)

Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of the Amplifier.

Using the video signal cable(s), connect the VIDEO, S-VIDEO, COMPONENT or HDMI OUT terminals on the rear of the DVD

player to the VIDEO, S-VIDEO, COMPONENT or HDMI-DVI IN terminal of your TV as described on pages 12 to 16.

Turn on the DVD player, TV, and Amplifier.

RED

WHITE

Audio Cable

RED WHITE

2-Channel stereo amp

Press the input select button of the Amplifier to select external input in order to hear sound from the DVD player.

Refer to your Amplifier's user manual to set the Amplifier's audio input.

Note

- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause damage to the speakers and your ears.

- Please set the audio in the menu screen according to the Amplifier.(See pages 50 to 51)

- The position of terminals may vary depending on the Amplifier. Please refer to the user's manual of the Amplifier.

ENG-18

CONNECTIONS

Connection to an Audio System (Dolby digital, MPEG2 or DTS Amplifier)

If using an optical cable (not included), connect the DIGITAL AUDIO OUT (OPTICAL) terminal on the rear of the DVD player

to the DIGITAL AUDIO IN (OPTICAL) terminal of the Amplifier. If using a coaxial cable (not included), connect the DIGITAL AUDIO OUT (COAXIAL) terminal on the rear of the DVD player to the DIGITAL AUDIO IN (COAXIAL) terminal of the Amplifier.

Using the video signal cable(s), connect the VIDEO, S-VIDEO, COMPONENT or HDMI OUT terminals on the rear of the DVD

player to the VIDEO, S-VIDEO, COMPONENT or HDMI/DVI IN terminals of your TV as described on pages 12 to 16.

Turn on the DVD player, TV, and Amplifier.

Optical Cable (not included)

Coaxial Cable (not included)

Dolby digital or

DTS amp

Connections

Press the input select button of the Amplifier to select external input in order to hear sound from the DVD player.

Refer to your Amplifier's user manual to set the Amplifier's audio input.

Note

- When you connect the DVD player to DTS Amplifier and play a DTS disc, set the DTS to On in Audio Setup menu. If it is set to Off, sound will not be heard, or there will be a loud sound.

- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause damage to the speakers and your ears.

- Please set the audio in the menu screen according to the Amplifier. (See pages 50 to 51)

- The position of terminals may vary depending on the Amplifier. Please refer to the user's manual of the Amplifier.

- Please remove the dust cover before using the optical cable (not included) and put the cover on the cable again when it's not used.

ENG-19

Chapter 3

BASIC FUNCTIONS

Playing a Disc

Before Play

- Turn on your TV and set it to the correct Video Input on the TV's remote control.

- If you connected the DVD player to an external Audio System, turn on your Audio System and set it to the correct Audio Input.

After plugging in the player, the first time you press the DVD POWER button, this screen comes up: If you want to select a language, press a NUMBER button. (This screen will only appear when you plug in the player for the first time.) If the language for the startup screen is not set, the settings may change whenever you turn the power on or off. Therefore, make sure that you select the language you want to use. Once you select a menu language, you can change it by pressing the button on the front panel of the unit for more than 5 seconds with no disc in the unit. Then the SELECT MENU LANGUAGE window appears again where you can reset your preferred language.

Playback

Press the OPEN/CLOSE ()button.

The STANDBY indicator light goes out and the tray opens.

Place a disc gently into the tray with the disc’s label facing up.

Press the PLAY/PAUSE ( ) button or OPEN/CLOSE ( ) button to close the disc tray.

▼

RESUME function

When you stop disc play, the player remembers

where you stopped, so when you press PLAY/PAUSE ( ) button again, it will pick up where you left off.

ENG-20

+ 44 hidden pages