Samsung DVD-HD950 User Manual

www.samsung.ca

AK68-00627F

DVD Player

DVD-HD950

Lecteur DVD

AK68-00627F

www.samsung.ca

Important Safety Instructions

Precautions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings, install in accordance with the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding- type plug. Apolarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus.

13) Unplug this apparatus. When a cart is used, use caution when moving the

cart/apparatus combination to avoid injury from tip-over.

14) Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This symbol indicates “dangerous voltage” inside the product that presents a risk of electric shock or

REMOVE THE COVER(OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates important instructions accompanying the product.

personal injury.

Do not install this equipment in a confined space such as a bookcase or similar unit.

WARNING : To prevent damage which may result in fire or electric shock hazard, do not expose

this appliance to rain or moisture.

CAUTION : DVD PLAYERS USE AN INVISIBLE LASER BEAM WHICH CAN CAUSE

HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE PLAYER CORRECTLYAS INSTRUCTED.

CAUTIONS

Caution: To prevent electric shock, match wide blade of plug to wide slot, fully insert. Attention: Pour éviter les chocs électriques, introduíre la lame la plus large de la fiche dans la borne

correspondante de la prise et pousser jusqu au fond. This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances, such as radios and televisions, use shielded cables and connectors for connections.

FCC NOTE (for U.S.A):

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures.

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect this equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This class B digital apparatus meets all requirements of the Canadian Interference -Causing Equipment Regulations.

CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT PRODUCTO LÁSER CLASE 1

ENG-2 ENG-3

ENG-5

Install Batteries in the Remote control

Open the battery cover on the back of the remote control.

Insert two AAAbatteries. Make sure that the polarities (+ and -) are aligned correctly.

Replace the battery cover.

If the remote control doesn’t operate properly:

- Check the polarity + - of the batteries (Dry-Cell).

- Check if the batteries are drained.

- Check if remote control sensor is blocked by obstacles.

- Check if there is any fluorescent lighting nearby.

Before you start

Accessories

Remote

Control

Batteries for

Remote Control

(AAA Size)

User’s Manual Video/Audio

Cable

Anynet Cable

ENG-4

CAUTION

THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVER AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

Note:

• This unit can be used only where the power supply is AC 120 V~ 60Hz. It cannot be used elsewhere.

• This DVD player is designed and manufactured to respond to the Region Management Information. If the Region number of a DVD disc does not correspond to the Region number of this DVD player, the DVD player cannot play the disc.

• The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. In particular, this product is licensed under the following US patents: 5,991,715, 5,740,317, 4,972,484, 5,214,678, 5,323,396, 5,539,829, 5,606,618, 5,530,655, 5,777,992, 6,289,308, 5,610,985, 5,481,643, 5,544,247, 5,960,037, 6,023,490, 5,878,080, and under US Published Patent Application No. 2001-44713-A1.

This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for commercial use. The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode audio files conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this license for product features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.

Handling Cautions

• Before connecting other components to this player, be sure to turn them all off.

• Do not move the player while a disc is being played, or the disc may be scratched or broken, and the player’s

internal parts may be damaged.

• Do not put a flower vase filled with water or any small metal objects on the player.

• Be careful not to put your hand into the disc tray.

• Do not place anything other than the disc in the disc tray.

• Exterior interference such as lightning and static electricity can affect normal operation of this player.

If this occurs, turn the player off and on again with the POWER button, or disconnect and then reconnect the AC power cord to the AC power outlet. The player will operate normally.

• Be sure to remove the disc and turn off the player after use.

• Disconnect the AC power cord from the AC outlet when you don’t intend to use the player for long

periods of time.

• Clean the disc by wiping in a straight line from the inside to the outside of the disc.

Disc Storage

Be careful not to harm the disc because the data on these discs is highly vulnerable to the environment.

• Do not keep under direct sunlight.

• Keep in a cool ventilated area.

• Store vertically.

• Keep in a clean protection jacket.

Maintenance of Cabinet

For safety reasons, be sure to disconnect the AC power cord from the AC outlet.

• Do not use benzene, thinner, or other solvents for cleaning.

• Wipe the cabinet with a soft cloth.

TABLE OF CONTENTS

Chapter 1

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Chapter 1:

Setup

General Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Disc Type and Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Tour of the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Chapter 2: Connections

Choosing a Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Chapter 3: Basic Functions

Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Using the Search and Skip Functions . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Using the Display Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Using the Disc and Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Using the Function Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Slow Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Program Play & Random Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Chapter 4: Advanced Functions

Adjusting the Aspect Ratio (EZ View). . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Selecting the Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Selecting the Subtitle Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Changing the Camera Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Using the Instant Replay/Skip Function . . . . . . . . . . . . . . . . . . . . . . . . . 37

Using the Bookmark Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Using the Zoom Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

DVD AUDIO Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Super Audio CD Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Clips Menu for MP3/WMA/JPEG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

MP3/WMA Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Picture CD Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Picture CD Playback for HD-JPEG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Chapter 5: Changing Setup Menu

Using the Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Setting up EZ-Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Setting Up the Language Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Setting Up the Audio Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Setting Up the Display Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Setting Up the Parental Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Chapter 6: Reference

Controlling a TV with the Remote. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

SETUP

General Features

Excellent Sound

Dolby Digital, a technology developed by Dolby Laboratories, provides crystal clear sound reproduction.

Screen

Both regular and widescreen(16:9) pictures can be viewed.

Slow Motion

An important scene can be viewed in slow motion.

Program Play (CD)

You can program tracks to play in desired order.

Parental Control (DVD)

The parental control allows users to set the level necessary to prohibit children from viewing harmful movies such as those with violence, adult subject matter, etc.

Various On-Screen Menu Functions

You can select various languages (Audio/Subtitle) and screen angles while enjoying movies.

Progressive Scan

Progressive scanning creates an improved picture with double the scan lines of a conventional interlaced picture.

EZ VIEW (DVD)

Easy View enables picture adjustment to match your TV's screen size (16:9 or 4:3).

Digital Photo Viewer (JPEG)

You can view Digital Photos on your TV.

Repeat

You can repeat a song or movie simply by pressing the REPEATbutton.

MP3/WMA

This unit can play discs created from MP3/WMA files.

Instant Replay (DVD)

This function is used to replay the previous 10 seconds of a movie from the current position.

Instant Skip (DVD)

This function skips playback ahead 10 seconds.

Super Audio CD

Super Audio CD is a high quality audio format with higher sampling rates and fuller, richer sound as compared to regular CD.

DVD AUDIO

DVD AUDIO is a format specifically designed to provide the highest possible audio fidelity capable on DVD.

Setup

HDMI (High Definition Multimedia Interface)

HDMI reduces picture noise by allowing a pure digital video/audio signal path from the player to your TV .

Note

-Discs which cannot be played with this player.

• DVD-ROM • DVD-RAM

• CD-ROM • CDV

• CDI • CVD

• CDGs play audio only, not graphics.

-Ability to play back may depend on recording conditions.

• DVD-R, +R

• CD-RW

• DVD+RW, -RW (V mode)

-The unit may not play certain CD-R, CD-RW and DVD-R due to the disc type or recording conditions.

COPY PROTECTION

Many DVD discs are encoded with copy protection. Because of this, you should only connect your DVD player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy-protected DVD discs.

This product incorporates copyright protection technology that is protected by methods claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

PROGRESSIVE SCAN OUTPUTS (525p)

“CONSUMERS SHOULD NOTE THAT NOTALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCTAND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE, IF 525 PROGRESSIVE SCAN PICTURE PROBLEMS OCCUR, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’OUTPUT. IF THERE ARE QUESTIONS REGARDING YOUR TV SET COMPATIBILITY WITH THIS MODEL 525p DVD PLAYER, PLEASE CONTACT SAMSUNG'S CUSTOMER SERVICE CENTER.”

ENG-6

ENG-7

SETUP

Setup

Disc Type and Characteristics

This DVD player is capable of playing the following types of discs with the corresponding logos:

Disc Types (Logos)

DVD-VIDEO

VIDEO-CD

AUDIO-CD

DVD-AUDIO

Super Audio CD

Recording Types Disc Size Max. Playing Time Characteristics

- DVD contains excellent sound and video due to Dolby Digital and MPEG-2 system.

- Various screen and audio functions can be easily selected through the on-screen menu.

- Video with CD sound, VHS quality & MPEG-1 compression technology.

- CD is recorded as a Digital Signal with better audio quality, less distortion and less deterioration of audio quality over time.

- DVD AUDIO is a format specifically designed to provide the highest possible audio fidelity capable on DVD.

- Super Audio CD is a high quality audio format with higher sampling rates and fuller, richer sound as compared to regular CD.

Audio

Video

Audio

Video

Audio

Video

Audio

31/2"

Single-sided 240 min.

Double-sided 480 min.

Single-sided 80 min.

Double-sided 160 min.

74 min.

20 min.

74 min.

20 min.

400 min.

74 min.

Description

Front Panel Controls

1 87

1. STANDBY/ON ( )

When the unit is first plugged in, this indicator lights. When STANDBY/ON is pressed on, the indicator goes out and the player is turned on.

2. DISC TRAY

Place the disc here.

3. OPEN/CLOSE ( )

Press to open and close the disc tray.

4. DISPLAY

Operation indicators are displayed here.

5. EZ VIEW

The aspect ratio of a picture can easily be adjusted to your TV's screen size (16:9 or 4:3).

23456

6. STOP ( )

Stops disc play.

7. REMOTE CONTROL RECEIVER

8. SKIP ( ) / SEARCH

Use to forward skip a scene or music.

9. SKIP ( ) / SEARCH

Use to reverse skip a scene or music.

10. PLAY/PAUSE ( )

Begin or pause disc play.

Disc Markings Region Number

NTSC

Play Region Number NTSC broadcast system in U.S.A, Canada, Korea,

Japan, etc. Dolby Digital disc

Both the DVD player and the discs are coded by region. These regional codes must match in order for the disc to play. If the codes do not match, the disc will not play.

STEREO

DIGITAL

SOUND

You must only insert one DVD disc at a time. Inserting two or more discs will not allow playback and may cause damage to the DVD player.

Stereo disc

Digital Audio disc

DTS disc

MP3 disc

DVD AUDIO disc

Super Audio CD disc

The Region Number for this player is described on the rear panel of the player. Canada is Region 1.

ENG-8

ENG-9

SETUP

Setup

Front Panel Display

3 6 7 8 9 10 11121314151617

1 2

1845

1. DVD : DVD is loaded Audio : DVD-Audio disc is playing

2. Super Audio CD is loaded

3. DTS (Digital Theater System) output

4. Dolby-Digital Disc

5. Progressive Scan Video output

6. DVD-Audio : Group number

7. DVD-Video : Title number

8. DVD-Audio, CD, Video CD, Super Audio CD : Track number

9. DVD-Video : Chapter number

10. DVD-Audio : Index number

11. Disc type indicators : SVCD (Super VCD), VCD, CD

12. MPEG Audio output

13. CVD (Chinese VCD) Disc indicator

14. MP3 Audio output

15. Linear PCM audio output

16. Lights when the device connected to the HDMI Jack is a DVI device

17. Lights when the device connected to the HDMI Jack is a HDMI device

18. Displays various messages concerning operations such as PLAY, STOP, LOAD ...

no DISC : No disc loaded. OPEN : The disc tray is open. LOAD : Player is loading disc information.

Rear Panel

12345667

1. ANYNET JACKS

- Use the Anynet cable to connect the Anynet jack of your Samsung television or AV device.

2. 5.1CH ANALOG AUDIO OUT JACKS

- Connect to an amplifier with 5.1ch analog input jacks.

3. DIGITALAUDIO OUT JACKS

- Use either an optical or coaxial digital cable to connect to a compatible Dolby Digital receiver.

- Use either an optical or coaxial digital cable to connect to an A/V Amplifier that contains a Dolby Digital, MPEG2 or DTS decoder.

4. AUDIO OUT JACKS

Connect to the Audio input jacks of your television or audio/video receiver.

5. VIDEO OUT JACK

- Use a video cable to connect to the Video input jack on your television.

- The Video Output in Setup Menu must be set to COMPONENT(I-SCAN) or COMPOSITE/S-VIDEO.

Note

Consult your TV User’s Manual to find out if your TV supports Progressive Scan (P-SCAN). If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s menu system.

- If HDMI/COMPONENT(P-SCAN) Video Output is selected in Setup Menu, Video and S-Video Outputs do not work.

- The HDMI output of this unit can be connected to a DVI jack on a TV or other device using a conversion adapter. In this case, it is necessary to use a TV or display with an HDCP-compatible DVI input.

- There may be no image output if the DVD player is connected to a TV or display that is not compatible with the above format.

- Refer to the TV's instruction manual for detailed information regarding the HDMI terminal.

- See pages 64 ~ 66 to get more information on how to use the setup menu.

6. S-VIDEO OUT JACK

- Use the S-Video cable to connect this jack to the S-Video jack on your television for higher picture quality.

- The Video Output in Setup Menu must be set to COMPOSITE/S-VIDEO.

7. HDMI OUT JACK

- Use the HDMI cable to connect this jack to the HDMI jack on your television for the best quality picture.

- If an HDMI cable is connected to an HDMI-compatible TV, HDMI will be output automatically a maximum of 10 seconds later.

- If you want to use a Video, S-Video or Component Output, unplug HDMI cable.

8. COMPONENT VIDEO OUT JACKS

- Use these jacks if you have a TV with Component Video in jacks. These jacks provide PR, PBand Y video.

- If HDMI/COMPONENT(P-SCAN) Video Output is selected in Setup Menu, progressive scan mode will work.

- If COMPONENT(I-SCAN) Video Output is selected in Setup Menu, interlaced scan mode will work.

ENG-10

ENG-11

SETUP

Chapter 2

Tour of the Remote Control

4 5 6

7 8

10 11 12

13 14

16 17

1. DVD POWER Button

Turns the power on or off.

2. NUMBER Buttons

3. PROG Button

Allows you to program a specific order.

4. STEP Button

Advances play one frame at a time.

5. VOL (+, -) Buttons

Control volume.

6. TV/VIDEO Button

Press to display all of the available video sources ( i.e., TV, Cable, Video)

19 20

21 22

26 27

29 30 31

32 33

7. VIDEO SEL. Button

Selects Video output format.

8. SEARCH Buttons ( / )

Allow you to search forward/backward through a disc.

9. STOP Button ( )

10. SKIP Buttons ( / )

Use to skip the title, chapter or track.

11. MENU Button

Brings up the DVD player’s menu.

12. RETURN Button

Returns to a previous menu.

13. ZOOM Button

Enlarges DVD picture.

14. AUDIO Button

Use this button to access various audio functions on a disc.

15. SUBTITLE Button

16. INDEX Buttons

Use to skip the INDEX.

17. SACD/CD Button

Selects Super Audio CD or CD playback mode.

18. TV POWER Button

Turns the TV’s power on or off.

19. CLEAR Button

Use to remove menus or status displays from the screen.

20. INSTANT SKIP Button

This function skips playback ahead 10 seconds.

21. INSTANT REPLAY Button

This function is used to replay the previous 10 seconds of a movie from the current position.

22. CH ( , ) Buttons

Channel selection.

23. OPEN/CLOSE ( ) Button

To open and close the disc tray.

24. HDMI SEL. Button

HDMI or DVI Output resolution setup.

25. PLAY/PAUSE Button ( )

Begin/Pause disc play.

26. INFO Button

Displays the current disc mode.

27. DISC MENU Button

Brings up the Disc menu.

28. ENTER/

This button functions as a toggle switch.

29. EZ VIEW Button

The aspect ratio of a picture can easily be adjusted according to the screen size of your TV (16:9 or 4:3).

30. ANGLE Button

Use to access various camera angles on a DVD.

31. REPEAT Button

Allows you to repeat play a title, chapter, track, or disc.

32. PAGE Buttons

Use to skip the PAGE.

33. BOOKMARK Button

34. SHUTTLE DIAL (Search mode)

Performs fast motion play.

35. JOG DIAL (Step mode)

Operates frame by frame play. In CD mode, performs track search.

❷❷➛➛❿❿

ENG-12

Buttons

CONNECTIONS

Choosing a Connection

The following shows examples of connections commonly used to connect the DVD player with a TV and other components.

Before Connecting the DVD Player

- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.

- Refer to the user’s manual of the additional components (such as a TV) you are connecting for more information on those particular components.

Connection to a TV (Video)

Using video/audio cables, connect the VIDEO (yellow)/AUDIO (red and white) OUT terminals on the rear of the DVD player to

the VIDEO (yellow)/AUDIO (red and white) IN terminals of your TV .

Turn on the DVD player and TV.

RED WHITE YELLOW

Audio Cable

Video Cable

RED WHITE YELLOW

Press the input selector on your TV remote control until the Video signal from the DVD player appears on the TV screen.

Note

- Noise may be generated if the audio cable is placed too close to the power cable.

- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 20 to 22)

- The number and position of terminals may vary depending on your TV set. Please refer to the user's manual of your TV.

- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of the DVD player.

- If you press the VIDEO SEL. button when DVD Player is in stop mode or no disc is inserted, the Video Output mode changes in the following sequence: (

(I-SCAN)

➝ HDMI/COMPONENT(P-SCAN)

- When the Video Output in Setup menu is set to HDMI/COMPONENT(P-SCAN), the Video and S-Video Outputs do not work.

COMPOSITE/S-VIDEO ➝ COMPONENT

)

ENG-13

Connections

CONNECTIONS

Connection to a TV (S-Video)

- Connecting to your TV using an S-Video cable.

- You will enjoy high quality video. S-Video separates the picture element into black and white(Y) and color(C) signals to present clearer images than regular video input mode. (Audio signals are delivered through the audio output.)

Using an S-Video cable (not included), connect the S-VIDEO OUT terminal on the rear of the DVD player to the S-VIDEO IN terminal of your TV.

Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of your TV.

Turn on the DVD player and TV.

RED

Press the input selector on your TV remote control until the SVideo signal from the DVD player appears on your TV screen.

RED

WHITE

Audio Cable

WHITE

S-Video Cable (not included)

Connection to a TV (Interlace)

- Connecting to your TV using Component video cables.

- You will enjoy high quality and accurate color reproduction images. Component video separates the picture element into black and white(Y), blue(PB), red(PR) signals to present clear and clean images. (Audio signals are delivered through the audio output.)

Using component video cables (not included), connect the COMPONENT VIDEO OUT terminals on the rear of the DVD player to the COMPONENT IN terminals of your TV.

Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of your TV.

Turn on the DVD player and TV.

Press the input selector on your TV remote control until the Component signal from the DVD player appears on the TV screen.

RED WHITE

Audio Cable

RED WHITE

RED

BLUE

GREEN

Component cable

RED

BLUE

GREEN

(not included)

Connections

Set the Video Output to COMPOSITE/S-VIDEO in the Display Setup menu. (See pages 64 to 66) You can use the VIDEO SEL. button to change the Video Output mode. (See page 12)

Note

- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 20 to 22)

- The number and position of terminals may vary depending on the TV set. Please refer to the user's manual of your TV.

ENG-14

Set the Video Output to COMPONENT(I-SCAN) in the Display Setup menu. (See pages 64 to 66) You can also use the VIDEO SEL. button to change the Video Output mode. (See page 13)

Note

- If Video output is incorrectly set to COMPOSITE/S-VIDEO with the Component cables connected, the screen will turn red.

- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 20 to 22)

- The component terminal of your TV may be marked “R-Y, B-Y, Y” or “Cr, Cb, Y” instead of “PR, PB, Y” depending on the manufacturer. The number and location of the terminals may vary depending on the TV set. Please refer to the user's manual of your TV.

ENG-15

CONNECTIONS

Connection to a TV (Progressive)

Using component video cables (not included), connect the COMPONENT VIDEO OUT terminals on the rear of the DVD player to the COMPONENT IN terminals of your TV.

Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of your TV.

Turn on the DVD player and TV.

Press the input selector on your TV remote control until the Component signal from the DVD player appears on the TV screen.

Set the Video Output to HDMI/COMPONENT(P-SCAN) in the Display Setup menu. (See pages 64 to 66) You can use the VIDEO SEL. button to change the Video Output mode. (See page 13)

RED WHITE

Audio Cable

RED

BLUE

Connecting to a TV with DVI Jack

Using the HDMI-DVI cable, connect the HDMI OUT terminal on the rear of the DVD player to the DVI IN terminal of your TV.

Connections

RED

BLUE

GREEN

Using the audio cables, connect the AUDIO (red and white)

terminals on the rear of the DVD player to the AUDIO

OUT (red and white) IN terminals of your TV.

Turn on the DVD player and TV.

RED WHITE

Audio Cable

RED WHITE

HDMI-DVI cable

Press the input selector on your TV remote control until the DVI signal from the DVD player appears on your TV screen.

GREEN

Component cable (not included)

Connecting to a TV with HDMI Jack

Using the HDMI cable connect the HDMI OUT terminal on the rear of the DVD player to the HDMI IN terminal of your TV.

To see the progressive video output,

- Consult your TV User’s Manual to find out if your TV supports Progressive Scan. If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s menu system.

- Depending on your TV, the connection method may differ from the illustration above.

Note

- What is "Progressive Scan"? Progressive scan has twice as many scanning lines as the interlace output method. Progressive scanning method provides better and clearer picture quality.

ENG-16

Press the input selector on your TV remote control until the HDMI signal from the DVD player appears on your TV screen.

HDMI VIDEO Specifications

When you press the HDMI SEL. button, 480p, 720p, 768p and 1080i are selected in order. The first press of the

HDMI SEL. button brings up the current resolution.

The second press allows you to change the HDMI output resolution.

- Depending on your TV, certain HDMI output resolutions may not work.

- Please refer to the user's manual of your TV.

- If HDMI or HDMI-DVI cable is plugged into TV, the DVD player’s output is set to HDMI/DVI within 10 seconds.

- If you set the HDMI output resolution 720p or 1080i, HDMI output provides better picture quality.

ENG-17

HDMI cable

CONNECTIONS

• HDMI (High Definition Multimedia Interface)

HDMI is an interface to enable the digital transmission of video and audio data with just a single connector. Using HDMI, the DVD player transmits a digital video and audio signal and displays a vivid picture on a TV having an HDMI input jack.

• HDMI connection description

HDMI connector - Both uncompressed video data and digital audio data (LPCM or Bit Stream data).

- The player outputs only a pure digital signal to the TV.

- If TV does not support HDCP (High-bandwidth Digital content protection), snow noise appears on the screen.

• Why does Samsung use HDMI?

Analog TVs require an analog video/audio signal. However, when playing a DVD, the data transmitted to a TV is digital. Therefore either a digital-to-analog converter (in the DVD player) or an analog-to-digital converter (in the TV) is required. During this conversion, the picture quality is degraded due to noise and signal loss. HDMI technology is superior because it requires no D/A conversion and is a pure digital signal from the player to your TV.

• What is the HDCP?

HDCP (High-bandwidth Digital Content Protection) is a system for protecting DVD content outputted via HDMI from being copied. It provides a secure digital link between a video source (PC, DVD, etc.) and a display device (TV, Projector, etc.). Content is encrypted at the source device to prevent unauthorized copies from being made.

Connection to a TV with Anynet Jack

What is Anynet?

- Anynet enables you to control Samsung AV devices through the menu display on the TV screen, using just the Samsung TV's remote control.

- This function works only with Samsung Anynet supported models.

- Using Anynet, you can easily control this DVD Player with your Samsung TV.

- For detailed operation steps and connections, refer to the Samsung TV Anynet user’s manual

- Please note that you need to set the Anynet on your Samsung TV to use the Anynet function.

Using an Anynet cable, connect the Anynet Input (Green) terminal on the rear side of the DVD player to Anynet Output (Black) terminal of the TV.

Using an Anynet cable, connect the Anynet Output (Black) terminal to Anynet Input (Green) terminal of other AV device.

BLACK

GREEN

BLACK

GREEN

DVD Receiver

AV Receiver

Set-Top Box

Recorder

Connections

Set up the Anynet function on the Samsung TV.

Note

- Anynet operation is only available with Samsung TV sets that support Anynet.

- If Component (Progressive) or S-Video connection is used, some Anynet features will not be available. Use Video/Audio cable for the connection.

- Anynet function will not operate when Input and Output terminals are connected improperly, because the TV cannot communicate with external devices.

- Anynet terminals consist of Input (Green) and Output (Black) terminals.

- Match the color-coded cables to terminals when you connect the Anynet cable.

ENG-18

ENG-19

CONNECTIONS

Connection to an Audio System (2 Channel Amplifier)

Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of the Amplifier.

Using the video signal cable(s), connect the VIDEO, S-VIDEO, COMPONENT or HDMI OUT terminals on the rear of the DVD

player to the VIDEO, S-VIDEO, COMPONENT, HDMI or DVI IN terminal of your TV as described on pages 13 to 17.

Turn on the DVD player, TV, and Amplifier.

2-Channel stereo amp

Press the input select button of the Amplifier to select external input in order to hear sound from the DVD player.

Refer to your Amplifier's user manual to set the Amplifier's audio input.

RED

RED WHITE

WHITE

Audio Cable

Connection to an Audio System (Dolby digital or DTS Amplifier)

If using an optical cable (not included), connect the DIGITAL AUDIO OUT (OPTICAL) terminal on the rear of the DVD player

to the DIGITAL AUDIO IN (OPTICAL) terminal of the Amplifier. If using a coaxial cable (not included), connect the DIGITAL AUDIO OUT (COAXIAL) terminal on the rear of the DVD player to the DIGITAL AUDIO IN (COAXIAL) terminal of the Amplifier.

Using the video signal cable(s), connect the VIDEO, S-VIDEO, COMPONENT or HDMI OUT terminals on the rear of the DVD

player to the VIDEO, S-VIDEO, COMPONENT, HDMI or DVI IN terminals of your TV as described on pages 13 to 17.

Coaxial Cable (not included)

Turn on the DVD player, TV, and Amplifier.

Optical Cable (not included)

Press the input select button of the Amplifier to select external input in order to hear sound from the DVD player.

Refer to your Amplifier's user manual to set the Amplifier's audio input.

Dolby digital or

DTS amp

Connections

Note

- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause damage to the speakers and your ears.

- Please set the audio in the menu screen according to the Amplifier. (See pages 60 to 61)

- The position of terminals may vary depending on the Amplifier. Please refer to the user's manual of the Amplifier.

ENG-20

Note

- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause damage to the speakers and your ears.

- Please set the audio in the menu screen according to the Amplifier. (See pages 60 to 61)

- The position of terminals may vary depending on the Amplifier. Please refer to the user's manual of the Amplifier.

- Please remove the dust cover before using the optical cable (not included) and put the cover on the cable again when it's not used.

- DVD-AUDIO only plays back two channel audio through the Digital Audio out. Multi-channel DVD-Audio discs are output through the Analog outputs.

- SACD plays back only through the Analog outputs. (See pages 61)

ENG-21

CONNECTIONS

Connection to a 5.1CH Analog Amplifier

Chapter 3

BASIC FUNCTIONS

If using audio cables for 5.1 CH Analog Amplifier (not included) connect the 5.1CH ANALOG AUDIO OUT terminals on the rear of the DVD player to the 5.1CH ANALOG AUDIO IN terminals of the 5.1CH Analog Amplifier.

Using the video signal cable(s), connect the VIDEO, S-VIDEO, COMPONENT or HDMI OUT terminals on the rear of the DVD

player to the VIDEO, S-VIDEO, COMPONENT, HDMI or DVI IN terminals of your TV as described on pages 13 to 17.

Turn on the DVD player, TV, and Amplifier.

Press the input select button of the Amplifier to select external input in order to hear sound from the DVD player.

Refer to your Amplifier's user manual to set the Amplifier's audio input.

GREEN

WHITE

BLACK

5.1ch Analog Amplifier

Playing a Disc

Before Play

- Turn on your TV and set it to the correct Video Input using your TV's remote control.

If you connected an external Audio System, turn on your Audio System and set it to the correct Audio Input.

After plugging in the player, the first time you press the DVD POWER button, this screen appears: If you want to select a language, press a NUMBER button. (This screen will only appear when you plug in the player for the first time.) If the language for the startup screen is not set, the settings may change whenever you turn the power on or off. Therefore, make sure that you select the language you want to use. Once you select a menu language, you can change it by pressing the button on the front panel of the unit for more than 5 seconds with no disc in the unit. Then the SELECT MENU LANGUAGE window appears again where you can reset your preferred language.

Playback

Press 1 for English

Touche 2 pour Français

Drücken Sie 3 für Deutsch

Pulsar 4 para Español

Premere 5 per Italiano

Druk op 6 voor Nederlands

Press the OPEN/CLOSE ()button.

The STANDBYindicator light turns off and the tray opens.

Basic Functions

Note

- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause damage to the speakers and your ears.

- Please set the audio in the menu screen according to the Amplifier. (See pages 60 to 61)

- The position of terminals may vary depending on the Amplifier. Please refer to the user's manual of the Amplifier.

ENG-22

Place a disc gently into the tray with the disc’s label facing up.

Press the PLAY/PAUSE ( ) button or OPEN/CLOSE ( ) button to close the disc tray.

ENG-23

▼

RESUME function

When you stop disc play, the player remembers

where you stopped, so when you press PLAY/PAUSE ( ) button again, it will pick up where you left off. (unless the disc is removed or the player is unplugged, or if you press the STOP ( ) button twice.)

BASIC FUNCTIONS

Stopping Play

Press the STOP ( ) button during play.

Removing Disc Press the OPEN/CLOSE ()button.

Pausing Play Press the PLAY/PAUSE ()or STEP button on the

remote control during play.

Step Motion Play (Except CD)

Turn the JOG DIAL clockwise or press the STEP button on the remote control during play.

Note

- If the player is left in the stop mode for more than one minute without any user interaction, a screen saver will be activated. Press the PLAY/PAUSE ( ) button to resume normal play.

- If the player is left in the stop mode for more than 30 minutes, the power will automatically turn off. (Automatic Power-Off Function)

▼

Screen stops, no sound. To resume, press the PLAY/PAUSE ( ) button

once again.

Note

If the player is left for about 5 minutes in pause mode, it will stop.

▼

Each time the button is pressed or Jog Dial is

turned, a new frame will appear. No sound is heard during STEP mode. Press the PLAY/PAUSE ( ) button to resume

normal play. You can only perform step motion play in the

forward direction.

Using the Search and Skip Functions

During play, you can search quickly through a chapter or track, and use the skip function to jump to the next selection.

Searching through a Chapter or Track

▼

During play, turn the SHUTTLE DIAL or press the SEARCH (or ) button on the remote control for more than 1 second.

Skipping Tracks

During play, press the SKIP ( or ) button.

During play, press the

and press again to search at a faster speed.

DVD VCD CD/SACD/DVD-AUDIO

▼

You can also use the Shuttle dial on the remote

control by turning.

(DVD, VCD)

- Forward Shuttle dial : 1/8

➝

Play

➝

- Reverse Shuttle dial : 2X

Note

- The speed marked in this function may be different from the actual playback speed.

- No sound is hearing during search mode (Except CD).

SEARCH ( or )

2X, 4X, 64X, 128X 4X, 8X 2X, 4X, 8X

➝

button

1/4 ➝1/2

➝

Basic Functions

Slow Motion Play (Except CD)

Press the SEARCH ( ) button to choose the play speed between 1/8, 1/4 and 1/2 of normal during PAUSE or STEP mode.

▼

No sound is heard during slow mode. Press the PLAY/PAUSE ( ) button to resume normal play. Reverse slow motion play will not work.

Note

This ( ) icon indicates the function is not available in the current mode.

ENG-24

- When playing a DVD, if you press the SKIP ( ) button, it moves to the next chapter. If you press the SKIP ( ) button, it moves to the beginning of the chapter. One more press makes it move to the beginning of the previous chapter.

- When playing a VCD 2.0 in Menu Off mode, or a VCD 1.1 or a CD, if you press the SKIP ( ) button, it moves to the next track. If you press the SKIP ( ) button, it moves to the beginning of the track. One more press makes it move to the beginning of the previous track.

- If a track exceeds 15 minutes when playing a VCD and you press the button, it moves forward 5 minutes. If you press the button, it moves backward 5 minutes.

ENG-25

Note

When VCD 2.0 is in Menu Off mode only, this function works. Select Menu Off by pressing the DISC MENU button.

BASIC FUNCTIONS

Using the Display Function

When Playing a DVD/VCD/CD

During play, press the INFO button on the remote control.

Press the /❷ buttons to select the desired item.

DVD

0:00:13

ENG 5.1CH

Off

▼

You can also select Info in the function menu by

pressing the MENU button.

BASIC FUNCTIONS

Press the ➛/❿ buttons to make the desired setup and then press the ENTER button.

To make the screen disappear, press the INFO button again.

Note

▼

You may use the number buttons of the remote

control to directly access a title, chapter or to start the playback from a desired time.

Basic Functions

VCD

0:00:43

0:00:48

▼

When VCD2.0 is in Menu Off mode only, this

function works. Select Menu Off by pressing the DISC MENU buton.

To access the desired title when there is more than one in the disc. For example, if there is more than one movie on a DVD, each movie will be identified.

Most DVD discs are recorded in chapters so that you can quickly find a specific passage (similar to tracks on an audio CD).

Allows playback of the film from a desired time. You must enter the starting time as a reference. The time search function does not operate on some discs.

Refers to the film's soundtrack language. In the example, the soundtrack is played in English 5.1CH. A DVD disc can have up to eight different soundtracks.

Refers to the subtitle languages available in the disc. You will be able to choose the subtitle languages or, if you prefer, turn them off from the screen. A DVD disc can have up to 32 different subtitles.

ENG-26

ENG-27

BASIC FUNCTIONS

Using the Disc and Title Menu

Using the Disc Menu (DVD)

During the playback of a DVD disc, press the MENU button on the remote control.

Press the /❷ buttons to select Disc Menu, then press the ❿ or ENTER button.

Using the Title Menu (DVD)

Press ENTER key for Disc Menu

During the playback of a DVD disc, press the MENU button on the remote control.

Press the /❷ buttons to select Title Menu, then press the ❿ or ENTER button.

Press ENTER key for Title Menu

Note

- Depending on the disc, the Disc Menu may not be avaliable.

- You can also use the Disc Menu, using the DISC MENU button on the remote control.

- In VCD 2.0 the DISC MENU button is used to select Menu On or Menu Off mode.

Note

- Depending on the disc, the Title Menu may not be avaliable.

- Title Menu will only be displayed if there are at least two titles in the disc.

Using the Function Menu

Using the Function Menu (DVD/VCD)

Press the MENU button during playback.

Press the /❷ buttons to select Function, then press the ❿or ENTER button.

- Info (See pages 26 to 27)

- Zoom (See page 40)

- Bookmark (See pages 38 to 39)

- Repeat (See pages 30 to 31)

- EZ View (See pages 33 to 34)

- Front Display Lights when the front display is selected ON.

Info Zoom Bookmark Repeat EZ View Front Display : On

Press the /❷ buttons to select one of the six functions. Then press the ❿ or ENTER button to access the function.

▼

You can also directly select these functions

(except Front Display) using their respective buttons on the remote control.

Note

- For VCD2.0, this function is available in Menu Off mode only. Select Menu Off by pressing the DISC MENU button.

Basic Functions

ENG-28

ENG-29

BASIC FUNCTIONS

Repeat Play

Repeat the current track, chapter, title, a chosen section (A-B), or all of the disc.

When playing a DVD/VCD/CD

Press the REPEAT button on the remote control. Repeat screen appears.

▼

Press the ➛/❿ buttons to select Chapter, Title or A-B, then press the ENTER button.

DVD

Off 01 01 A-B

VCD/CD

Off 01 01 A-B

REPEAT

ENTER

Using the A-B Repeat function

1. Press the REPEATA-B button at the point where you want repeat play to start (A). B is automatically highlighted.

2. Press the REPEATA-B button again at the point where you want repeat play to stop (B).

- To return to normal play, press the CLEAR button.

Note

A-B REPEAT does not allow you to set point (B) until at least 5 seconds of playback time has elapsed after point (A) has been set.

To return to normal play, press REPEAT button again, then press the ➛/❿ buttons to select Off and press ENTER button.

DVD

Off 01 01 A-B

VCD/CD

Off 01 01 A-B

REPEAT

ENTER

ENG-30

DVD repeats play by chapter or title, CD and

VCD repeat play by disc or track.

Chapter ( ): repeats the chapter that is

playing. Title ( ): repeats the title that is playing. Disc ( ): repeats the disc that is playing. Track ( ): repeats the track that is playing. A-B: repeats a segment of the disc that you

select.

Note

- Depending on a disc, the Repeat function may not be available.

- When VCD2.0 is in Menu Off mode only, this function works. Select Menu Off by pressing the DISC MENU buton.

Slow Repeat Play

This feature allows you slowly to repeat scenes containing sports, dancing, musical instruments being played etc., so you can study them more closely.

When playing a DVD/VCD

During play, press the PLAY/PAUSE ( ) button.

Press the SEARCH ( ) button to choose the play speed between 1/8, 1/4 and 1/2 of normal during PAUSE or STEP mode.

▼

Press the REPEAT button on the remote control. Press the ➛/❿ buttons to select A-B.

Press the ENTER button at the point where you want repeat play to start (A). B is automatically highlighted. Press the ENTER button at the point where you want the repeat play to stop (B).

The disc will play from Ato B repeatedly at the speed you chose.

▼

To set A-B REPEAT, set (A) first, then set (B) after the following slow play time has elapsed: 1/8x: wait 40 seconds, then press B

1/4x: wait 20 seconds, then press B 1/2x: wait 10 seconds, then press B

To return to normal play, press the CLEAR button and then press the PLAY/PAUSE

() button.

Using the A-B Repeat function

1. During slow playback, press the REPEATA-B button at the point where you want repeat play to start (A). B is automatically highlighted.

2. Press the REPEATA-B button again at the point where you want the repeat play to stop (B).

- To return to normal play, press the CLEAR button and then press the PLAY/PAUSE( ) button.

Note

When VCD2.0 is in Menu Off mode only, this function works. Select Menu Off by pressing the DISC MENU buton.

ENG-31

Basic Functions

BASIC FUNCTIONS

Program Play & Random Play

Chapter 4

ADVANCED FUNCTIONS

Program Play (CD)

Program Play allows you to select the order in which you want tracks to play.

During play, press the PROG button.

Press the buttons to select PROGRAM. Press the ENTER button.

Press the buttons to select the first track to add to the program. Press the ENTER button. The selection numbers appear in the Program Order box.

/❷/➛/❿

PROGRAM

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16

RANDOM

➛❿❿

Track Program Order

- - - - - - - -

PROGRAM 01

▼

- To return to the previous menu screen, press the RETURN button.

- To cancel the selected program order, press the CLEAR button.

- This unit can support a maximum of 20 programmed tracks.

Press the PLAY/PAUSE ()button.

The disc will be played in programmed order.

Random Play (CD)

Random Play plays a disc's tracks in random order.

Press the PROG button.

PROGRAM

➛❿❿

RANDOM

Adjusting the Aspect Ratio (EZ View)

To play back using aspect ratio (DVD)

Press the EZ VIEW button.

- The screen size changes when the button is pressed repeatedly.

- The screen zoom mode operates differently depending on the screen setting in the Display Setup menu.

- To ensure correct operation of the EZ VIEW button, you should set the correct aspect ratio in the Display Setup menu. (See pages 64 to 65).

WIDE SCREEN

EZ VIEW

If you are using a 16:9 TV

For 16:9 aspect ratio discs

- WIDE SCREEN Displays the content of the DVD title in 16:9 aspect ratio.

- SCREEN FIT

The top and bottom portions of the screen are cut off. When playing a 2.35:1 aspect ratio disc, the black bars at the top and bottom of the screen will disappear. The picture will look vertically stretched. (Depending on a type of disc, the black bars may not disappear completely.)

- ZOOM FIT

The top, bottom, left and right of the screen are cut off and the central portion of the screen is enlarged.

▼

To make the aspect ratio bar disappear, press the CLEAR button.

For 4:3 aspect ratio discs

- Normal Wide

Displays the content of the DVD title in 16:9 aspect ratio. The picture will look horizontally stretched.

- SCREEN FIT

The top and bottom portions of the screen are cut off and the full screen appears. The picture will look vertically stretched.

- ZOOM FIT

The top, bottom, left and right portions of the screen are cut off and the central portion of the screen is enlarged.

- Vertical Fit

When a 4:3 DVD is viewed on a 16:9 TV, black bars will appear at the left and right of the screen in order to prevent the picture from looking horizontally stretched.

Advanced

Functions

Press the select RANDOM. Press the ENTER button.

➛/❿

buttons to

Note

- Depending on a disc, the Program and Random Play functions may not be avaliable.

- While in playback mode, press the CLEAR button on the remote control to cancel Program Play or Random Play.

ENG-32

ENG-33

ADVANCED

FUNCTIONS

ADVANCED

FUNCTIONS

If you are using a 4:3 TV

For 16:9 aspect ratio discs

- 4:3 Letter Box

Displays the content of the DVD title in 16:9 aspect ratio. The black bars will appear at the top and bottom of the screen.

- 4:3 Pan & Scan

The left and right portions of the screen are cut off and the central portion of the 16:9 screen is displayed.

- SCREEN FIT

The top and bottom portions of the screen are cut off and a full screen appears. The picture will look vertically stretched.

- ZOOM FIT

The top, bottom, left and right of the screen are cut off and the central portion of the screen is enlarged.

For 4:3 aspect ratio discs

- Normal Screen

Displays the content of the DVD title in 4:3 aspect ratio.

- SCREEN FIT

The top and bottom portions of the screen are cut off and the full screen appears. The picture will look vertically stretched.

- ZOOM FIT

The top, bottom, left and right portions of the screen are cut off and the central portion of the screen is enlarged.

Note

EZ View may behave differently depending on the type of disc.

Selecting the Audio Language

You can select a desired audio language quickly and easily with the AUDIO button.

Using the AUDIO button (DVD/VCD/CD)

Press the AUDIO button. The Audio changes when the button is pressed repeatedly.

- The audio languages are represented by abbreviations.

When playing a VCD or CD, you can select among Stereo, Right or Left.

DVD

ENG

VCD/CD

DOLBY DIGITAL 5.1CH

AUDIO

Stereo

AUDIO

Advanced

Functions

ENG-34

To remove the AUDIO icon, press the CLEAR or

RETURN button.

Note

- This function depends on audio languages that are encoded on the disc and may not be available.

- ADVD disc can contain up to 8 audio languages.

- To have the same audio language come up whenever you play a DVD; Refer to “Using the Audio Language” on page 58.

ENG-35

ADVANCED

FUNCTIONS

ADVANCED

FUNCTIONS

Selecting the Subtitle Language

You can select a desired subtitle quickly and easily with the SUBTITLE button.

Using the SUBTITLE button (DVD)

Press the SUBTITLE button. The subtitle changes when the button is pressed repeatedly. The subtitle languages are represented by abbreviations.

DVD

SUBTITLE

Off

To remove the SUBTITLE icon, press the CLEAR or

RETURN button.

Note

- Depending on DVDs, you can change desired subtitle in the Disc Menu. Press the DISC MENU button.

- This function depends on what subtitles are encoded on the disc and may not be avaliable on all DVDs.

- ADVD disc can contain up to 32 subtitle languages.

- To have the same subtitle language come up whenever you play a DVD; Refer to “Using the Subtitle Language” on page

59.

Changing the Camera Angle

When a DVD contains multiple angles of a particular scene, you can use the ANGLE function.

Using the ANGLE button (DVD)

If the disc contains multiple angles, the ANGLE appears on the screen.

Press the ANGLE button, then the ANGLE icon will appear with the current angle number and the number of angles available.

ANGLE

Press the ANGLE button repeatedly to select the desired angle. To remove the ANGLE icon, press the CLEAR or RETURN button.

Using the Instant Replay/Skip Function

Using the Instant Replay function (DVD)

If you miss a scene, you can see it again using this function.

Press the INSTANT REPLAY button.

- The current scene moves backward about 10 seconds, and plays back.

4/6

Note

If the disc has only one angle, this feature won’t work. Currently, very few discs have this feature.

Advanced

Functions

ENG-36

Using the Instant Skip function (DVD)

Use this function to skip playback about 10 seconds ahead of the current scene.

Press the INSTANT SKIP button.

- Playback will skip ahead 10 seconds.

Note

Depending on the disc, these functions may not work.

ENG-37

ADVANCED

FUNCTIONS

ADVANCED

FUNCTIONS

Using the Bookmark Function

This feature lets you bookmark sections of a DVD or VCD (Menu Off mode) so you can quickly find them at a later time.

Using the Bookmark Function (DVD/VCD)

During play, press the BOOKMARK button on the remote control.

OR Using the MENU button. During play, press the MENU button on the remote control.

Press the select Function, then press the ❿or ENTER button.

Press the select Bookmark, then press the ❿or ENTER button.

/❷

buttons to

Info Zoom Bookmark Repeat EZ View Front Display : On

Info Zoom

Bookmark

Repeat EZ View Front Display : On

Recalling a Marked Scene

During play, press the BOOKMARK button on the remote control.

Press the select a marked scene.

➛/❿

buttons to

Press the PLAY/PAUSE ( ) button to skip to the marked scene.

Clearing a Bookmark

Advanced

Functions

When you reach the scene you want to mark, Press the ❿button to move to the next Bookmark and press the ENTER button. Up to three scenes may be marked at a time.

ENG-38

Note

- When VCD2.0 is in Menu Off mode only, this function works. Select Menu Off by pressing the DISC MENU buton.

- Depending on a disc, the Bookmark function may not work.

During play, press the BOOKMARK button on the remote control.

Press the select the bookmark number you want to delete.

➛/❿

buttons to

Press the CLEAR button to delete a bookmark number.

ENG-39

ADVANCED

FUNCTIONS

ADVANCED

FUNCTIONS

Using the Zoom Function

Using the Zoom Function (DVD/VCD)

During play, press the ZOOM button on the remote control.

OR Using the MENU button. During play or pause mode, press the MENU button on the remote control.

Press the select Function, then press the ❿or ENTER button.

Press the select Zoom, then press the❿or ENTER button.

/❷

buttons to

Info Zoom Bookmark Repeat EZ View Front Display : On

Info

Zoom

Bookmark Repeat EZ View Front Display : On

DVD AUDIO Playback

Open the disc tray. Place the DVD AUDIO disc on the tray.

- Place the DVD AUDIO disc with the labeled side up. Close the tray.

- The tray closes and disc plays.

During play, press the INFO button on the remote control.

Press the select the desired item.

/❷

buttons to

DVD-AUDIO

0:00:13

▼

You can select Info in the function menu by

pressing the MENU button.

Advanced

Functions

Press the buttons to select the part of the screen you want to zoom in on. Press the ENTER button.

/❷

➛/❿

ENG-40

▼

During DVD play, press ENTER to zoom in

2X/4X/2X/Normal in order.

During VCD play, press ENTER to zoom in

2X/Normal in order.

Note

For VCD2.0, this function works in Menu Off mode only. Select Menu Off by pressing the DISC MENU button.

Press the make the desired setup and then press the ENTER button.

➛/❿

buttons to

To make the screen disappear, press the INFO button again.

ENG-41

▼

You may use the number buttons of the remote

control to directly access a Group, Track, Page or to start the playback from the desired time.

▼

Some DVD-AUDIO discs don’t down-mix audio.

These discs always output 5.1ch analog audio regardless of audio setup.

ADVANCED

Slide

V-zone

FUNCTIONS

ADVANCED

FUNCTIONS

Note

Most DVD AUDIO discs are recorded in Groups you can change Groups with this Function. Bonus Group playback. Some DVD AUDIO discs have Bonus groups. If you want to play a Bonus group, you must enter the Bonus Group code. The code is usually on the DVD AUDIO disc case.

To access the desired Track when there is more than one on the DVD AUDIO disc. If pages are included with the DVD-AUDIO disc, you can see this icon.

To access the desired page, you can use this Function. If a slide show is included with the DVD-AUDIO disc, you can see this icon.

In this case, you cannot use PAGE PRE./NEXTbuttons. If a video zone is included with the DVD-AUDIO disc, you can see this icon.

In this case, you cannot use PAGE PRE./NEXTbuttons. Allows playback of music from a desired time by using the number buttons.

Note

The Bonus Group is the Hidden Group of the title by content provider. This is accessible only for the authorized user who knows the “Key numbers” to unlock the Hidden Group. “Key numbers” is determined by content provider and recorded in the Navigation information area on the Disc.

Page, Index Function

Note

Use PAGE PRE./NEXT buttons to Skip the Page when there is more than one in a group.

- Some DVD-AUDIO discs include a slide show. In the slide show mode, this function can not be used.

- PAGE is still images. You can see the still images when a DVDAUDIO disc is played back.

Depending on a disc, this function may not be available.

REPEAT Play

Press the REPEAT button on the remote control. Repeat screen appears.

Press the select Track, Group, then press the ENTER button.

AUDIO Format Display

➛/❿

buttons to

During DVD AUDIO playback, press the AUDIO button to see AUDIO Format information.

DVD-AUDIO

Off 01 01

DVD-AUDIO

PPCM 5.1CH

▼

Track ( ): repeats the track that is playing. Group ( ): repeats the group that is playing.

▼

- LPCM : Linear Pulse Code Modulation.

- PPCM : Packet Pulse Code Modulation.

Note

Some DVD-AUDIO discs don’t allow audio down-mixing.

Not compressed Audio data format.

Lossless compressed Audio data format.

Advanced

Functions

Use INDEX PRE./NEXT buttons to Skip the Index when there is more than one in a track.

ENG-42

ENG-43

ADVANCED

FUNCTIONS

ADVANCED

FUNCTIONS

Super Audio CD Playback

Open the disc tray. Place the Super Audio CD disc on the tray.

- Place the Super Audio CD

disc with the labeled side up. Close the tray.

- The tray closes and you should see a screen similar to this.

Super Audio CD Clips Menu On Play Function

Off

Use the

/❷

buttons to

select a music title.

Super Audio CD Clips Menu Off Play Function

In Stop mode, press the DISC MENU button until the Clips menu is off.

During play, press the INFO button on the remote control.

Press the select the desired item.

/❷

buttons to

SACD

0:00:13

MULTI

▼

You can select Info in the function menu by

pressing the MENU button.

Advanced

Functions

Press the ENTER button to begin playback of the music title.

- If you want to use the Repeat Function, press the REPEATbutton to change the mode, such as Off, Track, Disc.

* Off : Normal Playback * Track : Repeats the current

music title.

* Disc : Repeats the music

titles in the Super Audio CD.

▼

If you want to see information about the Disc

title and Artist, press the INFO button.

If you want to convert to regular CD mode,

press the SACD/CD button.

During play or stop mode, you can change the

2CH or MULTI mode by using LEFT/RIGHT buttons. (You can use this function when Super Audio CD disc includes both multi channel and 2 channel audio format.)

Press the make the desired setup and then press the ENTER button.

➛/❿

buttons to

To make the screen disappear, press the INFO button again.

▼

You may use the number buttons of the remote

control to directly access a track and to start the playback from the desired time.

ENG-44

ENG-45

+ 52 hidden pages