Samsung DVD-F1080-XAA User Manual

DVD Player

DVD-FP580

DVD-F1080

www.samsung.com

AK68-01464S

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings, Install in accordance with the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat registers,stoves, or other apparatus (including

amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has two blades and a third grounding prong.

The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use caution when

moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long peroids of

time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been

damaged in any way, such as the power-supply cord or plug is damaged, liquid has been spilled or objects

have fallen into the apparatus. Service is also required if the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

ENG-2

Precautions

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This symbol indicates that

dangerous voltage consisting a risk of electric shock is present within this unit.

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

Do not install this equipment in a confined space such as a bookcase or similar unit.

WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS

APPARATUS TO RAIN OR MOISTURE.

Note to CATV system installer : This reminder is provided to call CATV system installer’s attention to Article 820-40 of the National Electrical Code (Section 54 of Canadian Electrical Code, Part I) that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

Caution : FCC regulations state that any unauthorized changes or modifications to this equipment may

void the user’s authority to operate it.

• Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

• If this power supply is used at 240V ac, a suitable plug adapter should be used.

FCC NOTE (for U.S.A):

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures.

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect this equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help. This class B digital apparatus meets all requirements of the Canadian Interference -Causing Equipment Regulations.

CALIFORNIA USA ONLY :

This Perchlorate warning applies only to primary CR (Maganese Dioxide) Lithium coin cells in the product sold

or distributed ONLY in California USA “Perchlorate Material - special handling may apply , See www.dtsc.ca.gov/hazardouswaste/perchlorate.

CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT PRODUCTO LÁSER CLASE 1

ENG-3

CAUTION

THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR

PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVER AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

Note:

• This unit can be used only where the power supply is AC 120V, 60Hz. It cannot be used elsewhere.

• This DVD player is designed and manufactured to respond to the Region Management Information. If the Region number of a DVD disc does not correspond to the Region number of this DVD player, the DVD player cannot play the disc.

Handling Cautions

• Before connecting other components to this player, be sure to turn them all off.

• Do not move the player while a disc is being played, or the disc may be scratched or broken, and the player’s internal parts may be damaged.

• Do not put a flower vase filled with water or any small metal objects on the player.

• Be careful not to put your hand into the disc tray.

• Do not place anything other than the disc in the disc tray.

• Exterior interference such as lightning and static electricity can affect normal operation of this player. If this occurs, turn the player off and on again with the POWER button, or disconnect and then reconnect the AC power cord to the AC power outlet. The player will operate normally.

• Be sure to remove the disc and turn off the player after use.

• Disconnect the AC power cord from the AC outlet when you don’t intend to use the player for long periods of time.

• Clean the disc by wiping in a straight line from the inside to the outside of the disc.

• The Main plug is used as a disconnect device and shall stay readily operable at any time.

Disc Storage

Be careful not to harm the disc because the data on these discs is highly vulnerable to the environment.

• Do not keep under direct sunlight.

• Keep in a cool ventilated area.

• Store vertically.

• Keep in a clean protection jacket.

Maintenance of Cabinet

For safety reasons, be sure to disconnect the AC power cord from the AC outlet.

• Do not use benzene, thinner, or other solvents for cleaning.

• Wipe the cabinet with a soft cloth.

ENG-4

Before you start

Accessories

Remote Control

(AK59-00083B)

Install Batteries in the Remote control

Battery

Remote Control

(CR2025)

(AD43-00030A)

Open the battery

cover on the bottom side of the remote control.

Insert the battery

(CR2025). Make sure that the polarities (+ and -) are aligned correctly.

User’s Manual

(AK68-01464S)

Video/Audio

Cable

(AC39-42001R)

POWER AC-IN

Cable

(AD39-00076A)

Replace the battery

cover.

If the remote control doesn’t operate properly:

- Check the polarity + - of the battery.

- Check if the battery is drained.

- Check if the remote control sensor is blocked by obstacles.

- Check if there is any fluorescent lighting nearby.

ENG-5

TABLE OF CONTENTS

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Chapter 1:

Chapter 2: Connections

Chapter 3: Basic Functions

Chapter 4: Advanced Functions

Chapter 5: Navigating the Setup Menu

Chapter 6: Reference

Setup

General Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Disc Type and Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Tour of the Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Connecting to a TV with an HDMI Jack (DVD-F1080 only) . . . . . . . . . . 12

Connecting to a TV with a DVI Jack (DVD-F1080 only) . . . . . . . . . . . . 12

Connecting to a TV (Progressive) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Connecting to a TV (Interlace) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Connecting to a TV (Video) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Connecting to an Audio System (2 Channel Amplifier) . . . . . . . . . . . . . 17

Connecting to an Audio System (Dolby Digital, MPEG2 or DTS Amplifier) . 18

Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Using the Search and Skip Functions . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Using the Display Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Using the Disc and Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Using the Function Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Adjusting the Aspect Ratio (EZ View) . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Selecting the Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Selecting the Subtitle Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Changing the Camera Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Using the Bookmark Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Using the Zoom Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Clips Menu for MP3/WMA/JPEG/MPEG4/CD Audio . . . . . . . . . . . . . . . 35

Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

MP3/WMA/CD Audio Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Picture CD Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Using the Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Setting Up the Language Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Setting Up the Audio Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Setting Up the Display Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Setting Up the Parental Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Setting Up the Anynet+(HDMI-CEC) (DVD-F1080 only) . . . . . . . . . . . . 55

Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

ENG-6

Chapter 1

SETUP

General Features

Excellent Sound

Dolby Digital, a technology developed by Dolby

Laboratories, provides crystal clear sound reproduction.

Screen

Both regular and widescreen(16:9) pictures can be

viewed.

Slow Motion

An important scene can be viewed in slow motion.

1080p Playback (DVD-F1080 only)

This player upconverts regular DVDs for playback on

1080p TVs.

Parental Control (DVD)

The parental control allows users to set the level

necessary to prohibit children from viewing harmful movies such as those with violence, adult subject matter, etc.

Various On-Screen Menu Functions

You can select various languages (Audio/Subtitle)

and screen angles while enjoying movies.

Progressive Scan

Progressive scanning creates an improved picture

with double the scan lines of a conventional interlaced picture.

EZ VIEW (DVD)

Easy View enables picture adjustment to match your

TV's screen size (16:9 or 4:3).

Digital Photo Viewer (JPEG)

You can view Digital Photos on your TV.

Repeat

You can repeat a song or movie simply by pressing

the REPEAT button.

MP3/WMA

This unit can play discs created from MP3/WMA files.

MPEG4

This unit can play MPEG4 formats within an avi file.

HDMI (High Definition Multimedia

Interface) (DVD-F1080 only)

HDMI reduces picture noise by allowing a pure

digital video/audio signal path from the player to your TV.

Setup

Note

- Discs which cannot be played with this player.

• DVD-ROM • DVD-RAM

• CD-ROM • CDV

• CDI • CVD

• Super Audio CD(except CD layer)

• CDGs play audio only, not graphics.

- Ability to play back may depend on recording conditions.

• DVD-R, +R

• CD-RW

• DVD+RW, -RW (V mode)

- The unit may not play certain CD-R, CD-RW and DVD-R due to the disc type or recording conditions.

COPY PROTECTION

Many DVD discs are encoded with copy

protection. Because of this, you should only connect your DVD player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy-protected DVD discs.

This product incorporates copyright protection technology that is protected by methods claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

PROGRESSIVE SCAN OUTPUTS

(DVD-FP580(480p))/ (DVD-F1080(480p, 720p, 1080p))

“CONSUMERS SHOULD NOTE THAT NOT ALL HIGH

DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE, IF PROGRESSIVE SCAN PICTURE PROBLEMS OCCUR, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ (VIDEO) OUTPUT. IF THERE ARE QUESTIONS REGARDING YOUR TV SET COMPATIBILITY WITH THIS DVD PLAYER, PLEASE CONTACT SAMSUNG'S CUSTOMER SERVICE CENTER.”

ENG-7

SETUP

Disc Type and Characteristics

This DVD player is capable of playing the following types of discs with the corresponding logos:

Disc Types (Logos)

DVD

AUDIO-CD

Recording Types Disc Size Max. Playing Time Characteristics

- DVD contains excellent sound and video due to Dolby Digital and MPEG-2 system.

- Various screen and audio functions can be easily selected through the on-screen menu.

- CD is recorded as a Digital Signal with better audio quality, less distortion and less deterioration of audio quality over time.

Audio

Video

Audio

5”

3 1/2”

5”

3 1/2”

Single-sided 240 min.

Double-sided 480 min.

Single-sided 80 min.

Double-sided 160 min.

74 min.

20 min.

Disc Markings Region Number

NTSC

STEREO

DIGITAL

SOUND

Play Region Number

NTSC broadcast system in U.S.A, Canada, Korea, Japan, etc.

Dolby Digital disc

Stereo disc

Digital Audio disc

DTS disc

Both the DVD player and the discs are

coded by region. These regional codes must match in order for the disc to play. If the codes do not match, the disc will not play.

The Region Number for this player is described on the bottom panel of the player.

MP3 disc

You must only insert one DVD disc at a time.

Inserting two or more discs will not allow playback and may cause damage to the DVD player.

ENG-8

DivX Certification

DivX, DivX Certified,

and associated logos are

trademarks of DivXNetworks, Inc and

are used under license

Description

Front Panel Controls

SETUP

Setup

1. STANDBY/ON ( )

When STANDBY/ON is pressed on, the indicator goes out

and the player is turned on.

2. STANDBY Indicator

When the unit is first plugged in, the indicator lights.

3. DISC TRAY

Place the disc here.

4. OPEN/CLOSE ( )

Press to open and close the disc tray.

Rear Panel (DVD-FP580)

1. DIGITALAUDIO OUT JACKS

- Use a coaxial digital cable to connect to an A/V

Amplifier that contains a Dolby Digital, MPEG2 or DTS decoder.

2. COMPONENT VIDEO OUT JACKS

- Use these jacks if you have a TV with Component

Video in jacks. These jacks provide PR, PBand Y video.

- If

P-SCAN

Menu, progressive scan mode will work.

- If

I-SCAN

Menu, interlaced scan mode will work.

3. AUDIO OUT JACKS

is set to “ON” in Video Output of the Setup

5. SKIP ( ) / SEARCH

Use to reverse skip a scene or music.

6. STOP ( )

Stops disc play.

7. PLAY/PAUSE ( )

Begin or pause disc play.

8. SKIP ( ) / SEARCH

Use to forward skip a scene or music.

- Use audio cables to connect to the Audio input jacks of

your television or audio/video receiver

4. VIDEO OUT JACK

- Use a video cable to connect to the Video input jack on

your television.

5. AC IN JACK

- Use the AC IN cable(included) to connect this jack into

the power outlet.

ENG-9

Rear Panel (DVD-F1080)

SETUP

1. DIGITALAUDIO OUT JACKS

- Use a coaxial digital cable to connect to an A/V

Amplifier that contains a Dolby Digital, MPEG2 or DTS decoder.

2. COMPONENT VIDEO OUT JACKS

- Use these jacks if you have a TV with Component

Video in jacks. These jacks provide PR, PBand Y video.

- If

P-SCAN

Menu, progressive scan mode will work.

- If

I-SCAN

Menu, interlaced scan mode will work.

3. AUDIO OUT JACKS

- Use audio cables to connect to the Audio input jacks of

your television or audio/video receiver.

is set to “ON” in Video Output of the Setup

4. VIDEO OUT JACK

- Use a video cable to connect to the Video input jack on

your television.

5. AC IN JACK

- Use the AC IN cable(included) to connect this jack into

the power outlet.

6. HDMI OUT JACK

- Use an HDMI cable to connect this jack to the HDMI

jack on your television for the best quality picture.

- If an HDMI cable is connected to an HDMI-compatible TV, HDMI will be output automatically from the player about 10 seconds later.

Note

Consult your TV User’s Manual to find out if your TV supports Progressive Scan (P-SCAN).

If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s menu system.

- The HDMI output of this unit can be connected to a DVI jack on a TV or other device using a conversion

adapter. In this case, it is necessary to use a TV or display with an HDCP-compatible DVI input. (DVDF1080 only)

- Refer to the TV's instruction manual for detailed information regarding the TV’s HDMI input jack. (DVD-

F1080 only)

- See pages 50 ~ 52 to get more information on how to use the setup menu.

ENG-10

SETUP

Tour of the Remote Control

1 2

3 4 5

6 7 8

1. STANDBY/ON

Turns the power on or standby.

2. NUMBER Buttons

3. DISC MENU (NUMBER 4) Button

Brings up the Disc menu.

4. ZOOM (NUMBER 7) Button

16 17

Enlarges the DVD Picture.

5. INFO Button

Displays the current disc mode.

6. SEARCH Buttons (

Allow you to search forward/backward through a disc.

7. STOP Button ( )

8. SKIP Buttons (

Use to skip the title, chapter or track.

9. MENU Button

Brings up the DVD player’s menu.

10. ENTER /

This button functions as a toggle switch.

11. EXIT Button

Exit the on-screen menu.

12. OPEN/CLOSE ( ) Button

To open and close the disc tray.

13. AUDIO (NUMBER 5) Button

Use this button to access various audio functions on a disc.

14. REPEAT (NUMBER 6) Button

Allows you to repeat play a title, chapter, track or disc.

15. SUBTITLE (NUMBER 9) Button

16. VIDEO SEL. Button

Changes Video output mode.

17. EZ VIEW (NUMBER 0) Button

The aspect ratio of a picture can easily be adjusted

according to the screen size of your TV (16:9 or 4:3).

18. PLAY/PAUSE Button ( )

Begin/Pause disc play.

19. RETURN Button

Returns to a previous menu.

20. CANCEL Button

Use to remove menus or status displays from the screen.

/,¦¦/

Buttons

Setup

)

ENG-11

Chapter 2

CONNECTIONS

Choosing a Connection

The following shows examples of connections commonly used to connect the DVD player with a TV

and other components.

Before Connecting the DVD Player

- Always turn off the DVD player, TV, and other components before you connect or disconnect any

cables.

- Refer to the user’s manual of the additional components (such as a TV) you are connecting for more information on those particular components.

Connecting to a TV with an HDMI Jack (DVD-F1080 only)

Using an HDMI-HDMI cable (not included) connect the HDMI

OUT jack on the rear of the DVD player to the HDMI IN jack of

your TV.

Press the input selector button on your TV remote control until

the HDMI signal from the DVD player appears on your TV screen.

HDMI cable

(Not Included)

Connecting to a TV with a DVI Jack (DVD-F1080 only)

Using an HDMI-DVI cable (not included), connect the HDMI

OUT jack on the rear of the DVD player to the DVI IN jack of

your TV.

Using the audio cables, connect the AUDIO (red and white)

OUT jacks on the rear of the DVD player to the AUDIO (red and white) IN jacks of your TV.

Turn on your DVD player and TV.

Press the input selector button on your TV remote control until

the DVI signal from the DVD player appears on your TV screen.

ENG-12

RED

WHITE

Audio Cable (Included)

WHITE

HDMI-DVI cable (Not Included)

CONNECTIONS

HDMI VIDEO Specifications

- Depending on your TV, certain HDMI output resolutions may not work.

- Please refer to the user's manual of your TV.

- If an HDMI or HDMI-DVI cable is plugged into TV, the DVD player’s output is set to HDMI automatically about 10 seconds later.

- For better picture quality, set the HDMI output resolution to 720p, 1080i or 1080p (see page 51).

- This player upconverts regular DVDs for playback on 1080p TVs. It does not play HD DVDs or Blu-Ray discs.

- If you connect an HDMI cable between Samsung TV and this DVD player, you can operate this DVD player using your TV remote control. This is only available with Samsung TVs that support Anynet+(HDMICEC).(see page 55-56)

- If your TV has an logo, then it supports the Anynet+ function.

• HDMI (High Definition Multimedia Interface)

HDMI enables you to make a digital video and audio connection with a single cable.

Using HDMI, the DVD player transmits a digital video and audio signal which displays a vivid picture on a TV having an HDMI input jack.

• HDMI connection description

HDMI connector - Video and audio are transferred digitally without compression (LPCM or Bit Stream

data).

- The player outputs a pure digital signal to the TV through an HDMI cable.

- If your TV does not support HDCP (High-bandwidth Digital content protection), snow noise appears on the screen.

• Why does Samsung use HDMI?

Analog TVs require an analog video/audio signal. However, when playing a DVD, the signal transmitted to

a TV is digital. Therefore either a digital-to-analog converter (in the DVD player) or an analog-to-digital converter (in the TV) is required. During this conversion, the picture quality is degraded due to noise and signal loss. HDMI technology is superior because it requires no D/A conversion and is a pure digital signal from the player to your TV.

• What is HDCP?

HDCP (High-bandwidth Digital Content Protection) is a system for protecting DVD content output via

HDMI/DVI from being copied. It provides a secure digital link between a video source (PC, DVD. etc) and a display device (TV, projector, etc). Content is encrypted at the source device to prevent unauthorized copies from being made.

Connections

ENG-13

CONNECTIONS

Connecting to a TV (Progressive)

- Connecting to your TV using Component video cables. The 480p resolution is possible with this

connection.

- What is "Progressive Scan"? Progressive scan has twice as many scanning lines as the interlace output method and provides better and clearer picture quality.

Using Component video cables (not included), connect the COMPONENT VIDEO OUT jacks on the rear of the DVD player

to the COMPONENT IN jacks of your TV.

GREEN

BLUE

GREEN

Component cable (not included)

Using the audio cables, connect the AUDIO (red and white)

OUT jacks on the rear of the DVD player to the AUDIO (red and white) IN jacks of your TV.

Turn on the DVD player and TV.

Set the Video Output to P-SCAN in the Display Setup menu.

(See pages 50 to 52) You can also use the VIDEO SEL. button to change the Video Output mode. (See page 16)

RED

WHITE

RED

Audio Cable (Included)

RED

WHITE

RED

BLUE

Press the input selector button on your TV remote control until

the Component signal from the DVD player appears on the TV screen.

To see the progressive video output,

- Consult your TV User’s Manual to find out if your TV supports Progressive Scan. If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s menu system.

- Depending on your TV, the connection method may differ from the illustration above.

ENG-14

CONNECTIONS

Connecting to a TV (Interlace)

- Connecting to your TV using Component video cables. The 480i resolution is possible with this

connection.

- This is the best available connection if your TV is not capable of receiving a Progressive Scan signal.

- You will enjoy excelllent quality and accurate color reproduction images. Component video separates the picture element into black and white(Y), blue(P

), red(PR) signals to present clear

and clean images. (Audio signals are delivered through the audio output.)

Using Component video cables (not included), connect the COMPONENT VIDEO OUT jacks on the rear of the DVD player

to the COMPONENT IN jacks of your TV.

Connections

Using the audio cables, connect the AUDIO (red and white)

RED

BLUE

GREEN

OUT jackls on the rear of the DVD player to the AUDIO (red and white) IN jacks of your TV.

Turn on your DVD player and TV.

RED

WHITE

Set the Video Output to I-SCAN in the Display Setup menu.

(See pages 50 to 52) You can also use the VIDEO SEL. button to change the Video Output mode. (See page 16)

Audio Cable (Included)

WHITE

RED

GREEN

RED

BLUE

Component cable (not included)

Press the input selector on your TV remote control until the

Component signal from the DVD player appears on the TV screen.

Note

- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 17 to 18)

- The component jack of your TV may be marked “R-Y, B-Y, Y” or “Cr, Cb, Y” instead of “P depending on the manufacturer. The number and position of the jacks may vary depending on the TV set. Please refer to the user's manual of your TV.

, PB, Y”

ENG-15

CONNECTIONS

Connecting to a TV (Video)

Using Video/Audio cables, connect the VIDEO (yellow)/AUDIO

(red and white) OUT jacks on the rear of the DVD player to the

VIDEO (yellow)/AUDIO (red and white) IN jacks of your TV.

Turn on your DVD player and TV.

Press the input selector button on your TV remote control until

RED

WHITE

Audio Cable (Included)

WHITE

YELLOW

Video Cable (Included)

YELLOW

the Video signal from the DVD player appears on the TV screen.

Note

- Noise may be generated if the audio cable placed too close to the power cable.

- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 17 to 18)

- The number and position of the jacks may vary depending on your TV set. Please refer to the user's manual of your TV.

- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) jack of the DVD player.

- If you press the VIDEO SEL. button when the DVD Player is in play mode, stop mode or no disc is inserted, the Video Output mode changes in the following sequence: ( I-SCAN

➝ P-SCAN).

When HDMI is connected, these output modes will not appear.

ENG-16

CONNECTIONS

Connecting to an Audio System (2 Channel Amplifier)

Using the audio cables, connect the AUDIO (red and white)

OUT jacks on the rear of the DVD player to the AUDIO (red and white) IN jacks of the Amplifier.

Using the video signal cable(s), connect the VIDEO, COMPONENT or HDMI OUT jacks on the rear of the DVD

player to the VIDEO, COMPONENT or HDMI-DVI IN jack of your TV as described on pages 12 to 16.

Connections

RED WHITE

Turn on your DVD player, TV, and Amplifier.

2-Channel stereo amp

Audio Cable (Included)

RED

WHITE

Press the input select button of the Amplifier to select the audio

input your DVD player is connected to in order to hear sound. Refer to your Amplifier's user manual to set the Amplifier's audio input.

Note

- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause damage to the speakers and your ears.

- Please set the audio in the menu screen according to the Amplifier.(See pages 48 to 49)

- The position of jacks may vary depending on the Amplifier. Please refer to the user's manual of the Amplifier.

ENG-17

CONNECTIONS

Connecting to an Audio System (Dolby digital, MPEG2 or DTS Amplifier)

If using a Coaxial cable (not included), connect the DIGITAL

AUDIO OUT (COAXIAL) jack on the rear of the DVD player to

the DIGITAL AUDIO IN (COAXIAL) jack of the Amplifier.

Using the video signal cable(s), connect the VIDEO,

COMPONENT or HDMI OUT jacks on the rear of the DVD

player to the VIDEO, COMPONENT or HDMI-DVI IN jacks of your TV as described on pages 12 to 16.

Turn on your DVD player, TV, and Amplifier.

Coaxial Cable

(not included)

Dolby digital or

DTS amp

Press the input select button of the Amplifier to select the audio

input your DVD player is connected to in order to hear sound. Refer to your Amplifier's user manual to set the Amplifier's audio input.

Note

- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause damage to the speakers and your ears.

- Please set the audio in the menu screen according to the Amplifier you have connected. (See pages 48 to 49)

- The position of jacks may vary depending on the Amplifier. Please refer to the user's manual of the Amplifier.

ENG-18

Chapter 3

BASIC FUNCTIONS

Playing a Disc

Before Play

- Turn on your TV and set it to the Video Input your DVD player is connected to with your TV’s

remote control.

- If you connected the DVD player to an external Audio System, turn on your Audio System and set it to the correct Audio Input.

After plugging in the player, the first time you press the DVD POWER button, the screen to the right appears: If you want to select a language, press a NUMBER button. (This screen will only appear when you plug in the player for the first time.) If the language for the startup screen is not set, the settings may change whenever you turn the power on or off. Therefore, make sure that you select the language you want to use. Once you select a menu language, you can change it by pressing the ( )button on the front panel of the unit for more than 5 seconds with no disc in the unit. Then the

SELECT MENU LANGUAGE window appears again where you can reset your

preferred language.

Basic Functions

Playback

Press the OPEN/CLOSE

()button.

The STANDBY indicator light goes out and the tray opens.

Place a disc gently into the

tray with the disc’s label facing up.

Press the PLAY/PAUSE ( ) button or OPEN/CLOSE ( ) button to close the disc tray.

▼

RESUME function

When you stop disc play, the player remembers

where you stopped, so when you press the PLAY/PAUSE ( ) button again, it will pick up where you left off.

ENG-19

+ 44 hidden pages