Samsung DVD-E360, DVD-E350, DVD-E360K User Manual

DVD Player

User Manual

imagine the possibilities

Thank you for purchasing this Samsung product. To receive more complete service, please register your product at

DVD-E360K DVD-E360 DVD-E350

www.samsung.com/register

ENGLISH

Precautions

1. Setting up

Refer to the identification label located on

the

rear of your player for its proper

operating

adequate ventilation holes. (7~10cm) Do not block ventilation holes on any of the components

- Do not push the disc tray in by hand.

- Do not stack components.

- Be sure to turn all components off before moving the player.

- Before connecting other components to this player, be sure to turn them off.

- Be sure to remove the disc and turn off the player after use, especially if you are not going to use it for a long time.

- The mains plug is used as a disconnect device and shall stay readily operable at any time.

2. For your safety

- This product utilizes a laser. Use of controls of procedures herein may result in hazardous radiation exposure.

self personal.

3. Caution

- Your player is not intended for industrial use but for domestic purposes. Use of this product is for personal use only.

- Apparatus shall not be exposed to dripping with liquids placed on the apparatus.

- Exterior influences such as lightning and static electricity can affect normal opera tion of this player. If this occurs, turn the player off and on again with the POWER button, or disconnect and then recon nect the AC power cord to the AC power outlet. The player will operate normally.

- When condensation forms inside the player due to sharp changes in tempera-

voltage.

Install your player in a cabinet with

for air circulation.

or adjustments or performance

other than those specified

Do not open covers and do not repair your

. Refer servicing to qualified

or splashing and no objects filled

, such as vases, shall be

ture, the player may not operate cor rectly. If this room temperature player becomes dry and operational.

4. Disc

- Do not clean disc using record-cleaning sprays, benzene, thinner, or other vola tile solvents that may cause damage to the disc surface.

- Do not touch the disc’s bottom. Hold by the edges or by one edge and the hole in the center.

- Wipe the dirt away gently; never wipe a cloth back and forth over the disc.

5. Environmental info

- The battery used in this product contains

chemicals that are harmful to the environment.

- So, dispose the batteries in the proper manner, according to federal, state, and local regulations.

The product unit accomparied this user manual is licenced under certain intellectual property rights of certain third parties. This licence is limited to by end-user consumers No rights are granted for commercial use. The licence does not cover any product unit other than this product unit and the licence does not extend to any unlicenced product unit or process conforming to ISO/OUR 11172-3 or ISO/ OUR 13818-3 used or sold in combination with this product unit. The licence only covers the use of this product unit to encode and/or decode audio files conforming to the ISO/OUR 11172-3 or ISO/OUR 13818-3. No rights are granted under this licence for product features or functions that do not con form to the ISO/OUR 11172-3 or ISO/OUR 13818-3.

CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER THAN SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

occurs, leave the player at

until the inside of the

private non-commercial use

for licenced contents.

Table of contens

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Setup

General Features . . . . . . . . . . . . . . . . . . . . . . 2

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Tour of the Remote Control . . . . . . . . . . . . . . . 4

Connections

Choosing a Connection . . . . . . . . . . . . . . . . . 4

Basic Functions

Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . 5

Using the Search and Skip Functions . . . . . . 5

Using the Display Function . . . . . . . . . . . . . . 5

Using the Disc and Title Menu . . . . . . . . . . . . 6

Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Advanced Functions

Adjusting the Aspect Ratio (EZ View) . . . . . . . 6

Selecting the Audio Language . . . . . . . . . . . . 6

Selecting the Subtitle Language . . . . . . . . . . . 6

Changing the Camera Angle . . . . . . . . . . . . . . 7

Using the Bookmark Function . . . . . . . . . . . . 7

Using the Zoom Function . . . . . . . . . . . . . . . . 7

Clips Menu for MP3/WMA/JPEG/MPEG4/

CD Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Setup

General Features

Excellent Sound

Dolby Digital, a technology developed by Dolby Laboratories, provides crystal clear sound reproduction.

Screen

Both regular and widescreen(16:9) pictures can be viewed.

Slow Motion

An important scene can be viewed in slow motion.

Parental Control (DVD)

The parental control allows users to set the necessary level to prohibit children from viewing harmful movies such as those with violence, adult subject matter, etc.

Various On-Screen Menu Functions

You can select various languages (Audio/ Subtitle) and screen angles while enjoying movies.

Folder Selection . . . . . . . . . . . . . . . . . . . . . . . 7

MP3/WMA/CD Audio Playback. . . . . . . . . . . . 7

MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . 8

Playing Media Files using the USB HOST

feature (Only DVD-E360K, E360) . . . . . . . . . . 8

CD Ripping (Only DVD-E360K, E360) . . . . . . . 9

Picture CD Playback . . . . . . . . . . . . . . . . . . . . 9

Karaoke Functions (Only DVD-E360K)

Karaoke Functions . . . . . . . . . . . . . . . . . . . . 10

Changing Setup Menu

Using the Setup Menu . . . . . . . . . . . . . . . . . 10

Setting Up the Display Options. . . . . . . . . . . 10

Setting Up the Audio Options . . . . . . . . . . . . 11

Setting Up the System Options . . . . . . . . . . 11

Setting Up the Language Features . . . . . . . . 11

Setting Up the Security Options . . . . . . . . . . 11

Setting Up the General Options . . . . . . . . . . 12

Setting Up the Support Options . . . . . . . . . . 12

Reference

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 12

Specifications . . . . . . . . . . . . . . . . . . . . . . . . 13

EZ VIEW (DVD)

Easy View enables picture adjustment to match your TV's screen size (16:9 or 4:3).

Digital Photo Viewer (JPEG)

You can view Digital Photos on your TV.

Repeat

You can repeat a song or movie simply by pressing the REPEAT button.

MP3/WMA

This unit can play discs contain MP3/WMA files.

MPEG4

This unit can play MPEG4 formats within an avi file.

CD Ripping (Only DVD-E360K, E360)

This feature lets you to copy audio files from disc to USB device into MP3 format. (Only Audio CD (CD DA))

Note

▼

▼ ▼

▼

- Discs which cannot be played with this player.

 • DVD-ROM •DVD-RAM  • CD-ROM •CDV  • CDI •CVD

- Ability to play back may depend on recording conditions.

 • DVD-R,+R  • CD-RW  • DVD+RW,-RW(Vmode)

- The unit may not play certain CD-R, CD-RW and DVD-R due to the disc type or recording conditions.

COPY PROTECTION

Many DVD discs are encoded with copy protection. Because of this, you should only connect your DVD player directly to your TV, not to a VCR. Connecting to a VCR results a distorted picture from copy-protected DVD discs.

This item incorporates copy protection technology that is protected by U.S. patents and other intellectual property rights of Rovi Corporation. Reverse engineering and disassembly are prohibited.

CLASS 1 LASER PRODUCT

This Compact Disc player is classified as a CLASS 1 LASER product. Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

CAUTION :

CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO THE BEAM (IEC 60825-1).

THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVER AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

CLASS 1 LASER PRODUCT KLASSE 1

LASER PRODUKT LASER LAITE LASER APPARAT

LÁSER CLASE 1

LUOKAN 1 KLASS 1 PRODUCTO

Disc Markings

Play Region Number

PAL broadcast system in U.K,

PAL

France, Germany, etc.

Dolby Digital disc

STEREO

Stereo disc

DIGITAL

Digital Audio disc

SOUND

MP3 disc

Region Number

Both the DVD player and the discs are coded by region. These regional codes must match in order for the disc to play. If the codes do not match, the disc will not play.

The Region Number for this player is described on the rear panel of the player.

DivX Certification

DivX®, DivX Certified® and associated logos are trademarks of Rovi Coorporation or its subsidiaries and are used under license. ABOUT DIVX VIDEO : DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit www.divx.com for more information and software tools to convert your files into DivX video. ABOUT DIVX VIDEO-ON-DEMAND : This DivX Certified® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod.divx.com for more information on how to complete your registration. “DivX Certified to play DivX video, including premium content.”

Covered by one or more of the following U.S patents : 7,295,673; 7,460,668; 7,515,710; 7,519,274.

Description

Front Panel Controls

DVD-E360K

DVD-E360

DVD-E350

1. DISC TRAY

Place the disc here.

2. DISPLAY Operation indicators are displayed here.

3. OPEN/CLOSE ( )

Press to open and close the disc tray.

4. PLAY/PAUSE ( )

Play or pause the disc.

5. POWER ON/OFF ( )

Turn on/off and the player is turned on/

off.

6. USB HOST (Only DVD-E360K,E360)

Connect digital still camera, MP3 player,

memory stick, Card reader other removable storage devices.

7. MIC (Only DVD-E360K)

Connect Microphone for karaoke func-

tions.

Tour of the Remote Control

DVD-E360K

1 2

5 6

1. DVD POWER Button

Turns the power on or off.

2. REPEAT Button

Allows you to repeat play a title, chapter,

track, or disc.

3. DISC MENU Button

Brings up the Disc menu.

4. RECORD Button

(Only DVD-E360K)

Use to Karaoke recording.

5. SEARCH Buttons ( / )

Allows you to search forward/backward through a disc.

6. STOP Button ( )

To stop the disc

7. SKIP Buttons ( / )

Use to skip the title, chapter or track.

8. MENU Button

Brings up the DVD player’s menu.

9. ENTER/π/†,√/® Buttons

This button functions as a toggle switch.

10. AUDIO Button (√)

Use this button to access various audio functions on a disc.

11. TOOLS Button

Displays the current disc mode. It also lets you access the Display function.

12. OPEN/CLOSE ( ) Button

12 13

14 15

17 18

DVD-E360

1 2

5 6 7

DVD-E350

6 7

To open and close the disc tray.

13. VIDEO SEL. Button

Changes video output mode.

14. USB Button (Only DVD-E360K,E360)

To change device which access to USB

device.

15. MARKER Button

16. PLAY Button (

Begins disc play.

17. SUBTITLE/(π) Button

18. RETURN Button

Returns to a previous menu

19. TITLE MENU Button (®)

Brings up the Title menu.

20. KARAOKE (†) Button (Only DVD-E360K)

To acces karaoke menu (keycon, mic volume,

echo).

21. INFO Button

Used to displays playback info banner.

22. REPEAT A-B Button (Only DVD-E360,E350)

Allows you to repeat A-B disc.

23. ZOOM Button (Only DVD-E350)

Enlarges the DVD Picture.

)

12 13 23 15

17 18

Connections

Choosing a Connection

The following shows examples of connections commonly used to connect the DVD player with a TV and other components.

Before Connecting the DVD Player

- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.

- Refer to the user’s manual of the additional components you are connecting for more information on those particular components.

A. Connecting to a TV (For Video)

1. Using video/audio cables, connect the VIDEO (yellow)/AUDIO (red and white) OUT terminals on the rear of the DVD player to the VIDEO (yellow)/AUDIO (red and white) IN terminals of TV.

2. Turn on the DVD player and TV.

3. Press the input selector on your TV remote control until the Video signal from the DVD player

appears on the TV screen.

Note

- Noise may be generated if the audio cable is too close to the power cable.

- If you want to connect to an Amplifier, please refer to the Amplifier connection page.

- The position of terminals can vary depending on your TV set. Please refer to the user’s manual of the TV.

- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of the DVD player.

- If you press the VIDEO SEL. button when DVD Player is in stop mode or no disc is inserted, the Video Output mode changes in the following sequence: (SCART-RGB ➝ SCART-CVBS).

B. Connection to an Audio System (2 Channel Amplifier, Dolby Digital,

MPEG2)

1. Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD

player to the AUDIO (red and white) IN terminals of the Amplifier. If using a coaxial cable, connect the DIGITAL AUDIO OUT (COAXIAL) terminal on the rear of the DVD player to the DIGITAL AUDIO

IN (COAXIAL) terminal of the Amplifier.

2. Using the video signal cable(s), connect the VIDEO terminals on the rear of the DVD player to the VIDEO terminals of your TV

3. Turn on the DVD player, TV, and Amplifier.

4. Press the input select button of the Amplifier to select external input in order to hear sound from the

DVD player. Refer to your Amplifier's user manual to set the Amplifier's audio input.

C. Connecting to a TV (SCART)

Using Scart cable, connect to SCART terminal on the rear of the DVD player to the SCART IN

terminals of TV.

Turn on the DVD player and TV.

Press the input selector on your TV remote control until the Video signal from the DVD player appears on the TV screen.

WHITE

RED

Coaxial kabel

WHITE

RED

Video kabel

Audio kabel

WHITE

RED

YELLOW

Scart kabel

Audio kabel

WHITE

RED

Basic functions

Playing a Disc

Before Play

- Turn on your TV and set it to the correct Video Input by pressing TV/VIDEO button on the TV remote control.

- If you connected an external Audio System, turn on your Audio System and set it to the correct Audio Input.

After plugging in the player, the first time you press the DVD POWER button, this screen comes up: If you want to select a language, press the π/† button, and then press the ENTER button. (This screen will only appear when you plug in the player for the first time.)If the language for the startup screen is not set, the set-tings may change whenever you turn the power on or off. Therefore, make sure that you select the language you want to use.Once you select a menu language, you can change it by pressing the

®|| button on the front panel of the unit for more than 5 seconds with no disc in the unit. Then the

SELECT MENU LANGUAGE window appears again where you can reset your preferred language.

Using the Search and Skip Functions

During play, you can search quickly through a chapter or track, and use the skip function to jump to the next selection.

Searching through a Chapter or Track

During play, press the SEARCH (k or K) button on the remote control for more than 1 second.

2X, 4X, 8X, 16X, 32X

DVD

2X, 4X, 8X, 16X, 32X

Note

- The speed marked in this function may be different from the actual playback speed.

- No sound is hearing during search mode (Except CD).

Skipping Tracks

During play, press the SKIP (|k or K|) button.

- When playing a DVD, if you press the SKIP (K|) button, it moves to the next chapter. If you press the SKIP (|k) button while play time <5s,it moves to previous chapter, but if you press SKIP (|k), while play time >5s it moves to the beginning of the current chapter.

- When playing a CD, if you press the SKIP (

) button while play time <5s,it moves to previous track,

but if you press SKIP (|k) while play time >5s it moves to the beginning of the current track.

Using the Display Function

When Playing a DVD/MPEG4

1. During play, press the TOOLS button on the remote control.

2. Press the π/† buttons to select the desired item.

3. Press the √/® buttons to make the desired setup.

4. To make the screen disappear, press the TOOLS button again.

The Tool Button Display functions are listed in the table below.

To access the desired title when there is more than one in the disc. For example, if there is more than one movie on a DVD, each movie will be identified.

Most DVD discs are recorded in chapters (similar to tracks on an audio CD). Select this function to find and play a specific chapter.

Allows playback of the film from a desired time. You must enter the starting time as a reference. The time search function does not operate on some discs.

Lets you select the soundtrack language for a film. A DVD disc can have up to eight different soundtracks.

Lets you select the subtitle language or, if you prefer, turn off subtitles. A DVD disc can have up to 32 different sets of subtitles, each in a different language.

Lets you choose the EZ-View type

Select to activate the Zoom function.

Some DVDs have scenes that have been recorded at multiple angles. Use the Angle function to view a scene at one of those angles.

Using the Disc and Title Menu

During the playback of a DVD disc, press the DISC MENU/TITLE MENU button on the remote control.

Note

- Depending on a disc, the Disc Menu/Title Menu may not work.

- You can also use the Disc Menu, using the DISC MENU button on the remote control.

- Title Menu will only be displayed if there are at least two titles in the disc.

Repeat Play

Repeat the current track, chapter, title, a chosen section (A-B), or all of the disc.

When playing a DVD

1. Press the REPEAT button on the remote control. Repeat screen appears.

2. Press the REPEAT or π/† button to change playback mode.

- Off.

- Title : repeats the title that is playing.

- Chapter : repeats the chapter that is playing.

- Repeat A-B

Using the A-B Repeat function (DVD-E360K)

1. Press the REPEAT button on the remote control. The repeat screen appears.

2. Press the π/† button

3. Press the ENTER at the point where you want repeat play to start (A).

4. Press the ENTER at the point where you want repeat play to start (B).

Using the A-B Repeat function (DVD-E360, E350)

1. Press the REPEAT A-B button on the remote control.

2. Press the REPEAT A-B at the point where you want repeat play to start (A).

3. Press the REPEAT A-B at the point where you want repeat play to stop (B).

3. To return to normal play, press the REPEAT A-B

Note

A-B REPEAT allows you to set point (B) directly after point (A) has been set.

- Depending on a disc, the Repeat function may not work.

to select the REPEAT A-B and then press ENTER.

button until the display shows Repeat : Off

DVD repeats play by chapter or title.

Slow Play

This feature allows you slowly to repeat scenes containing sports, dancing, musical instruments being played etc., so you can study them more closely.

When playing a DVD

1. During play, press the PLAY ( ) button.

2. Press the SEARCH (k/K) button to choose the play speed between 1/2, 1/4, 1/8 and 1/16

and so on. If you want to go normal play press PLAY button.

Advanced functions

Adjusting the Aspect Ratio (EZ View)

To play back using aspect ratio (DVD)

1. During play, press the TOOLS button on the remote control.

2. Press the π/† buttons to select

changes. For graphics of the screen sizes and lists of the sequences in which the sizes change, see the next column.

3. Press the RETURN button to exit EZ View.

If you are using a 16:9 TV For 16:9 aspect ratio discs

- WIDE SCREEN

- SCREEN FIT

- ZOOM FIT

For 4:3 aspect ratio discs

- Normal Wide

- SCREEN FIT

- ZOOM FIT

- Vertical Fit

Note

This function may behave differently depending on the type of disc.

Selecting the Audio Language

You can select a desired audio language quickly and easily with the AUDIO button.

Using the AUDIO

1. During play, Press the AUDIO (√) button. Change the audio language by pressing the π/†

button.

- The audio languages are represented by abbreviations.

2. To remove the AUDIO icon, press the RETURN button.

Note

- This function depends on audio languages are encoded on the disc and may not work.

- A DVD disc can contain up to 8 audio languages.

(√)

Selecting the Subtitle Language

You can select a desired subtitle quickly and easily with the SUBTITLE/(π) button.

Using the SUBTITLE (π) button (DVD/MPEG4)

1. During play, Press the SUBTITLE

2. Press the SUBTITLE

SUBTITLE

3. Press the RETURN button to exit the Subtitle function

(π)

or π/† button, the language changes.

icon. Each time you press the √/® buttons, the screen size

If you are using a 4:3 TV For 16:9 aspect ratio discs

- 4:3 Letter Box

- 4:3 Pan Scan

- SCREEN FIT

- ZOOM FIT

For 4:3 aspect ratio discs

- Normal Screen

- SCREEN FIT

- ZOOM FIT

button (DVD/MPEG4)

(π)

or π/† button to change the language. Each time you press the

button.

Note

- The subtitle languages are represented by abbreviations.

- You have to change the desired subtitle in the Disc Menu, according to discs. Press the DISC MENU button.

- This function depends on what subtitles are encoded on the disc and may not work on all DVDs.

- A DVD disc can contain up to 32 subtitle languages.

Changing the Camera Angle

When a DVD contains multiple angles of a particular scene, you can use the ANGLE function.

Using the ANGLE function (DVD)

If the disc contains multiple angles, the ANGLE appears on the screen.

1. During play, press the TOOLS button on the remote control.

2. Press the π/† buttons to select

buttons on the remote control to select the desired angle option.

icon. When the angle screen is displayed, press the √/®

Using the Bookmark Function

This feature lets you bookmark sections of a DVD so you can quickly find them at a later time.

Using the Bookmark Function (DVD)

1. During play, press the MARKER button on the remote control.

2. When you reach the scene you want to mark, press the √/® or π/† buttons, and then press MARKER button. Up to 12 scenes may be marked at a time.

Note

- The Bookmark function may not work, depending on a disc,

Recalling a Marked Scene

1. During play, press the MARKER button on the remote control.

2. Press the √/® orπ/† buttons to select a marked scene.

3. Press the PLAY (

®||

) button to skip to the marked scene.

Clearing a Bookmark

1. During play, press the MARKER button on the remote control.

2. Press the √/® orπ/† buttons to select the bookmark number you want to delete.

3. Press the ENTER button to delete a bookmark number.

Using the Zoom Function

- Using the Zoom Function (DVD-E350)

During play or pause mode

- Using the Zoom Function (DVD-E360,E360K)

1. During play or pause mode, press the TOOLS buttons on the remote control.

2. Press the π/† buttons to select

- During DVD play, press ENTER to zoom in 1X/2X/3X/4X/ Normal in order.

, press the ZOOM button on the remote control.

icon, then press the ENTER button.

Clips Menu for MP3/WMA/JPEG/MPEG4/CD Audio

CD Audio or discs with MP3/WMA/JPEG/MPEG4 files contain individual songs and/or pictures. The player organizes these discs into folders that contain only one content type (for example, only pictures, only music, etc.). The folders function much like the folders you use on your computer. To go access these folders and the files in them, follow these steps :

1. Open the disc tray. Place the disc on the tray.

2. Close the tray. The tray closes and the Parent Folder Menu screen

appears (top screen image.) Parent folders contain all the Peer folders that have the same kind of content: music, video, photos, etc.

3. Press the √/® buttons to select the Parent folder of your choice, and then press the ENTER. A screen displaying the Peer folders appears. The Peer folders contain all the folders with the same kind of content (video, music, photos, etc.) that are in the Parent folder.

Videos \ 1/2 Pages

CD Pages Move Return

Folder Selection

The folder can be selected both in Stop or Play mode.

- To select the Parent Folder

Press the RETURN button to go to parent folder, or press the π/† buttons to select “..” and

press ENTER to go to the parent folder.

- To select the Peer Folder Press the π/† buttons to select the desired folder, then press ENTER.

- To select the Sub-Folder Press the π/† buttons to select the desired folder, then press ENTER.

MP3/WMA/CD Audio Playback

1. Open the disc tray. Place the disc on the tray. Close the tray.

2. Press the √/® buttons to select a Music folder, and then press ENTER. Press the π/† to select a song file, and then press ENTER. Press π/† to begin playback of the song file, and then press the

ENTER button.

Repeat/Random playback Press the REPEAT button to change the playback mode. There are four modes, such as Off, Track,

Folder and Random.

): Normal Playback

- Off (

): Repeats the current song file.

- Track (

- Folder (

- Random ( To resume normal play, press the REPEAT button until Repeat : Off.

CD-R MP3/WMA file When you record MP3 or WMA files on a CD-R for playback in this unit, please note the following:

- Your MP3 or WMA files should be in ISO 9660 or JOLIET format.

ISO 9660 format and Joliet MP3 or WMA files are compatible with Microsoft’s DOS and Windows, and

- When naming your MP3 or WMA files, do not exceed 8 characters, and enter “.mp3, or .wma” as

General name format : Title.mp3. or Title.wma. When composing your title, make sure that you use

): Repeats the song files which have the same extension in the current folder.

): Song files which have the same extension will be played in random order.

with Apple’s Mac. This format is the most widely used.

the file extension.

8 characters or less, have no spaces in the name, and avoid the use of special characters including:

(.,/,\,=,+).

- Use a decompression transfer rate of at least 128 Kbps when recording MP3 files.

The sound quality of MP3 files depends on the rate of compression/decompression you choose. To

get good MP3 CD audio sound requires an analog/digital sampling rate of at least 128 Kbps , but not more than 160 Kbps. Choosing higher rates, such as 192 Kbps or more, only rarely gives better sound quality. MP3 Files with decompression rates below 128 Kbps will not play properly.

- Use a decompression transfer rate of at least 64Kbps when recording WMA files.

The sound quality of WMA files depends on the rate of compression/decompression you choose. To

get good WMA CD audio sound requires an analog/digital sampling rate of at least 64 Kbps, but not more than 192 Kbps. WMA files with compression rates below 64 Kbps or above 192 Kbps will not play properly. WMA files only support sampling rates > 30 Khz.

- Do not try recording copyright protected MP3 files.

Windows MediaTM files (a registered trade mark of Microsoft Inc) and SDMITM files (a registered trade

mark of the SDMI Foundation) are encrypted and code protected to prevent illegal copying. You cannot copy these files.

- Important:

The recommendations above cannot be taken as a guarantee that the DVD player will play MP3

recordings, or as an assurance of sound quality. You should note that certain technologies and methods for MP3 file recording on CD-Rs prevent optimal playback of these files on your DVD player (degraded sound quality and in some cases, inability of the player to read the files).

- This unit can play a maximum of 500 files and 500 folders per disc.

MPEG4 Playback

MPEG4 Play Function

The MPEG4 audio and video data compatible with this player are contained in AVI files. This unit can only play AVI format files with an “.avi” extension.

1. Open the disc tray. Place the disc on the tray. Close the tray.

2. Press the √/® buttons to select a Video Menu, and then press the ENTER. Press the π/† to select an avi file (DivX), and then press the ENTER button.

Repeat and Repeat A-B playback

1. Press the REPEAT button , then press REPEAT or π/† buttons to change playback mode.

There are 3 modes, such as Off, Title and Folder.

- Off : No Repeat mode.

- Title : repeats the title that is playing.

- Folder : repeats the AVI files which have the same extension in the current folder.

Repeat A-B

Repeat A-B playback (DVD-E360K)

1. Press the REPEAT button on the remote control. The repeat screen appears.

2. Press the π/† button

3. Press the ENTER at the point where you want repeat play to start (A).

4. Press the ENTER at the point where you want repeat play to start (B).

Repeat A-B playback (DVD-E360, E350)

1. Press the REPEAT A-B button on the remote control.

2. Press the REPEAT A-B at the point where you want repeat play to start (A).

3. Press the REPEAT A-B at the point where you want repeat play to stop (B).

- To return to normal play, press the REPEAT A-B button until the display shows Repeat : Off

to select the REPEAT A-B and then press ENTER.

Note

A-B REPEAT allow you to set point (B) directly after point (A) has been set.

MPEG4 Function Description

Function Description

Skip

(|k or K|)

(k or K)

Slow Motion Play

ZOOM 1X/2X/3X/4X/Normal in order.

- These functions may not work depending, on MPEG4 file.

CD-R AVI file

This unit can play the following video compres-

sion formats within the AVI file format:

- DivX 3.11 contents

- DivX 4 contents (Based on MPEG-4 Simple Profile)

- DivX 5 contents (MPEG-4 simple profile plus additional features such as bi-directional frames. Qpel and GMC are also supported.)

DVD-RW & DVD+R

Format that support for DivX file :

- Basic DivX format DivX3.11 / 4.12/ 5.x

- DivX Pro

- File format : *.avi, *.div, *.divx.

Note

•TheresolutionthatcanbesupportedbyDVD-E360K/E360/E350 model up to 720 x 480 @30 frames and 720 x 576 @25 frames

•ThisunitsupportsCD-R/RWwritteninMPEG4inaccordancewiththe“ISO9660format”.

During play, press the |k or K|

During play, press the SEARCH (k or K) button and press again to search at a faster speed. Allows you to search at a faster speed in an AVI file. (2X, 4X, 8X, 16X, 32X)

During play, press the PLAY ( to view video at a slower speed. (1/2, 1/4, 1/8, 1/16)

button, it moves to next or previous track.

(

) button, and then press the SEARCH (K) button

This unit supports all resolutions up to maximum below.

DivX5

720 x 480 @30fps 720 x 576 @25fps : Maximum bit rate : 4Mbps

Possible warning messages that may appear when trying to play DivX/AVI files are :

No Authorization

- File with bad registration code.

Unsupported Codec

- Files with certain Codec Types, Versions (ex. MP4, AFS and other proprietary codecs) are not suppoerted by this player.

Unsupported Resolution

- Files containing resolutions higher than the player’s specification are not supported.

Playing Media Files Using the USB Host feature (ONLY DVD-E360K, E360)

You can enjoy the media files such as pictures, movies and tunes saved in an MP3 player, USB memory or digital camera in high audio by connecting the storage device to the USB port of the DVD Player.

Using the USB HOST feature

1. Connect the USB device to the USB port on the front of the unit.

2. The USB Menu screen appears. Press the √/® button to select Menu, and then press ENTER.

3. Press the π/† buttons to select a file in the USB device. Press ENTER to open the file. Switching Between DVD and USB

If you have a disk in the player, and you are viewing or listening to files on a USB device, or the USB Menu is on the screen, you can switch from the USB device to the disc by pressing the USB button on the remote.

Also, you can switch from the disc to the USB device by pressing the USB button on the remote. “USB loading...” appears on the screen, and then the USB Menu appears.

Note

- Depending on the file size and clip duration, loading time for a USB device may take longer than a CD or DVD.

Safe USB Removal

1. Press the USB button to return to disc mode or the main screen.

Press the STOP (■) button

Remove the USB cable/device.

Skip Forward/Back

During playback, press the (|k/K|) button.

When there is more than one file, when you press the K| button, the next file is selected.

•

When there is more than one file, when you press the |k button, the previous file is selected.

•

Fast playback

To play back the disc at a faster speed, press (k/K) during playback.

Each time you press either button, the playback speed will change as follows :

•

2X ➞ 4X ➞ 8X ➞ 16X ➞ 32X.

Compatible Devices

1. USB devices that support USB Mass Storage v1.0.(USB devices that operate as a removable disk in Windows (2000 or later) without additional driver installation.)

2. MP3 Player: Flash type MP3 player.

3. Digital camera: Cameras that support USB Mass Storage v1.0.

 • CamerasthatoperateasaremovableDiscinWindows(2000orlater)withoutadditionaldriver

installation.

4. USB Flash Drive: Devices that support USB2.0 or USB1.1.

 • YoumayexperienceadifferenceinplaybackqualitywhenyouconnectaUSB1.1device.

5. USB card Reader: One slot USB card reader and Multi slot USB card reader

 • Dependingonthemanufacturer.theUSBcardreadermaynotbesupported.  • Ifyouinstallmultiplememorydevicesintoamulticardreader,youmayexperienceproblems.

6. If you use a USB extension cable, the USB device might not be recognized.

Note

•CBI(Control/Bulk/Interrupt)isnotsupported.

•DigitalCamerasthatusePTPprotocolorrequireadditionalprograminstallationwhenconnectedtoa

PC are not supported.

•AdeviceusingNTFSfilesystemisnotsupported.(OnlyFAT16/32(FileAllocationTable16/32)file

system is supported.)

•SomeMP3players,whenconnectedtothisproduct,maynotoperatedependingonthesectorsize

of their file system.

•TheUSBHOSTfunctionisnotsupportedifaproductthattransfersmediafilesbyitsmanufacturer-

specific program is connected.

•DoesnotoperatewithJanusenabledMTP(MediaTransferProtocol)devices.

•TheUSBhostfunctionofthisproductdoesnotsupportallUSBdevices.

•TheUSBHostdoesnotsupportUSBHardDiscDrives(HDD).

CD Ripping (Only DVD-E360K, E360)

This feature lests you to copy audio files from a CD onto a USB device in MP3 format. Open the dics tray. Place the Audio CD (CD DA) disc on the tray, and close the tray. Connect the

USB device to the USB port on the front of the unit. Press the USB button.

1. Press the TOOLS button to display the Ripping screen.

2. Press the π/† buttons, then press the ENTER button to select files for ripping.

- To deselect files, press ENTER button again.

3. Press the √ and † button to select START, then press the ENTER button begin ripping. The Ripping menu contain the following buttons :

- Mode (Fast/Normal)

- Bitrate, press ENTER to change : 128kbps ➞ 192kbps ➞ 128kbps.

  •Standard:128kbps   •BetterQuality:192kbps

- Device selection, press ENTER to change between partitions on the USB device (max 4).

- Select - Unselect, press ENTER to change from Select all (files) or Select none.

Note

- To cancel copying in progress, press the ENTER button.

- To return to CDDA screen, press the TOOLS button again.

- When the CD ripping being processed the player will automatic in play mode.

- Ripping process is 2.6 times of normal speed.

- Only the Audio CD(CD DA) dics can be ripping.

- The USB button does not work while you’re in the Ripping menu.

- CD ripping function may not supported for some MP3 players device.

Picture CD Playback

1. Select the desired folder.

2. Press the

Note

- Press the STOP button to return to the clips menu.

Rotation

- Press the TOOLS button to select Rotate, and then press ENTER.

- Each time the √/® buttons are pressed, the picture rotates 90 degrees clockwise.

- Each time the π button is pressed, the picture will reverse to the upside down to show a mirror image.

- Each time the † button is pressed, the picture will reverse to the right side to show a mirror image.

Zoom

- Press the TOOLS button to select Zoom, and then press ENTER.

- Each time ENTER button is pressed, the picture is enlarged. Zoom mode : X1-X2-X3-X4-X1.

- Press the √/®/

Slide Show

- When you press the PLAY at JPEG file, it will go to full screen mode and automatically slide show.

π/†

buttons to select a Picture file in the clips menu and then press the ENTER button.

When playing a Kodak Picture CD, the unit displays the Photo directly, not the clips menu.

π/†

buttons to move the enlarged picture so you can view different portions.

Note

- Depending on a file size, the amount of time between each picture may be different from the manual.

- If you don’t press any button, the slide show will start automatically in about 10 seconds by default.

CD-R JPEG Disc

- Only files with the “.jpg” and “.JPG” extensions can be played.

- If the disc has not been closed during the recording phase,(ie has not been finalised) it will take longer to start playing and not all of the recorded files may be played.

- Only CD-R discs with JPEG files in ISO 9660 or Joliet format can be played.

- The name of the JPEG file may not be longer than 8 characters and should contain no blank

spacesorspecialcharacters(./=+).

- Only a consecutively written multi-se ssion disc can be played.If there is a blank segment in the multi-session disc, the disc can be played only up to the blank segment.

- A maximum of 500 images can be stored on a single CD.

- Kodak Picture CDs are recommended.

- When playing a Kodak Picture CD, only the JPEG files in the pictures folder can be played.

- Kodak Picture CD: The JPEG files in the pictures folder can be played automatically.

- Konica Picture CD: If you want to see the Picture, select the JPEG files in the clips menu.

- Fuji Picture CD: If you want to see the Picture, select the JPEG files in the clips menu.

- QSS Picture CD: The unit may not play QSS Picture CD.

- If the number of files in 1 Disc is over 500, only 500 JPEG files can be played.

- If the number of folders in 1 Disc is over 500, only JPEG files in 500 folders can be played.

Karaoke functions (Only DVD-E360K)

Karaoke Functions

Operation Sequence

1. Connect the terminals Mixed Audio Out to TV or Amplifier.

2. Connect the microphone plug to Mic (microphone) and set Karaoke score to On. When MIC is con-

nected and Karaoke score is On, the karaoke functions can be used.

Echo/Microphone Volume/Key Control (Tone control)

1. Play the karaoke disc containing the songs you want.

- Press the KARAOKE (†) button, and then press π/† to select ECHO, VOL or KEY.

2. Press the √/® buttons to change the desired value.

Karaoke Scoring (Score)

The scoring will appear as :

1. The microphone is connected and Karaoke score is On.

2. At the end of each chapter/title of karaoke disc.

- If the DVD karaoke have any information on the scoring drive.

3. Karaoke score will appear at the end of time for each chapter/title for about 6s.

Karaoke Sound Recording

1. Insert USB storage media into USB jack and then connected the microphone plug to Mic.

2. To star karaoke recording, choose one of DVD file, then press RECORD button.

3. When recording, user can only press STOP button and PAUSE button to cancel the recording.

4. If user do cancelation, then file result will be saved.

Note

- If you hear feedback(squealing or howling) while using the karaoke feature, move the microphone away from the speakers or turn down the microphone volume or the speaker volume.

- When playing MP3, WMA and LPCM disc, the karaoke functions will not operate.

- When the MIC is connected, Digital Out does not work.

- The MIC sound outputs only from Analog Audio Out.

- If MIC is connected to the MIC jack on the front panel, 5.1CH audio will be changed in to 2 CH audio automatically, this condition can’t be change unless the MIC is plugged out.

MY KARAOKE

My Karaoke is the feature that makes non karaoke DVD can be used like karaoke disc, by removing lead singer vocal sound.

Using the My Karaoke feature :

1. Connect the microphone.

2. Choose My Karaoke setting in Setting --> Audio --> My Karaoke and then select one of three enable

mode :

- Original Vocal : This setting will keep the original vocal sound.

- Min. Reduction : this setting reduce the main vocals sound sligthly.

- Max. Reduction : This setting will reduce the main vocals sound greatly

3. Insert and play DVD media, this feature only for DVD non karaoke type.

Note

1. Feature will disabled when :

- Removing the microphone, or

- Changing “My Karaoke” settings to “Original Vocals” or

- Playing Karaoke audio, or

- Playing non supported file type (ex : *.avi: *.mp3; *.divx; etc)

2. No pop-up notification when feature disabled.

Changing setup menu

Using the Setup Menu

The Setup menu lets you customize your DVD player by allowing you to select various language preferences, set up a parental level, even adjust the player to the type of television screen you have.

1. With the unit in Stop mode, press the MENU button on the remote control. Press the √/® buttons to select SETTINGS, then press the ENTER button.

2. Press the π/† buttons to select a Setup Menu, then press the ® or ENTER to bring up the sub- menu.

3. Press the π/† buttons to select a sub-menu option, then press the ® or ENTER.

4. To make the setup screen disappear after setting up, press the RETURN button.

Setting Up the Display Options

Display options enable you to set various video functions of the player.

1. With the unit in Stop mode, press the MENU button. Press the √/® buttons to select SETTINGS, then press the ENTER button.

2. Press the π/† buttons to select DISPLAY, then press the ® or ENTER button.

3. Press the π/† buttons to select the desired item, then press the ® or ENTER button.

Note

• If VideoOutputissetincorrectly,thescreenmaybeblocked.

• When theresolutionischangedduringplayback,itmaytakeafewsecondsforanormal

image to appear.

Setting Up the Audio Options

Audio Options allows you to setup the audio device and sound status settings depending on the audio system in use.

1. With the unit in Stop mode, press the MENU button. Press the √/® buttons to select

SETTINGS, then press the ENTER button.

2. Press the π/† buttons to select AUDIO, then press the ® or ENTER button.

3. Press the π/† buttons to select the desired item, then press the ® or ENTER button.

Note :

- When play a disc that has MPEG Audio and you have Bitstream selected in the Audio Options

menu, the Digital Audio jack may not output audio

- There is no analogue audio output when you play a sound disc.

- Even when PCM Down sampling is Off

 •Somediscswillonlyoutputdownsampledaudiothroughthedigitaloutputs.

Manufactured under licence from Dolby Laboratories. “Dolby” and the double-D symbol are trade-

marks of Dolby Laboratories.

Setting Up the System Options

1. With the unit in Stop mode, press the MENU button. Press the √/® buttons to select SETTINGS, then press the ENTER button.

2. Press the π/† buttons to select SYSTEM, then press the ® or ENTER button.

3. Press the π/† buttons to select the desired item, then press the ® or ENTER button.

Setting Up the Language Features

If you set the player menu, disc menu, audio and subtitle language in advance, they will come up automatically every time you watch a movie.

1. With the unit in Stop mode, press the MENU button. Press the √/® buttons to select SETTINGS, then press the ENTER button.

2. Press the π/† buttons to select LANGUAGE, then press the ® or ENTER button.

3. Press the π/† buttons to select the desired language, then press the ® or ENTER button.

Note

- The language is selected and the screen returns to Language Setup menu.

- To make the setup menu disappear, press the MENU button.

- If the selected language is not recorded on the disc, the original pre-recorded language is selected.

- Select “Original” if you want the defaultsoundtrack language to be the original language the disc

is recorded in.

- Select “Automatic” if you want the subtitle language to be the same as the language selected as the audio language.

- Some discs may not contain the language you select as your initial language; in that case the disc will use its original language setting.

Setting Up the Security Options

The Parental Control function works in conjunction with DVDs that have been assigned a rating, which helps you control the types of DVDs that your family watches. There are up to 8 rating levels on a disc.

Setting Up the Rating Level

1. With the unit in Stop mode, press the MENU button. Press the √/® buttons to select SETTINGS, and then press the ENTER button.

2. Press the π/† buttons to select SECURITY, and then press the ® or ENTER button.

3. The first time you access security, you must enter the default password: 0000. To enter the

default password, highlight 0 on the screen and press the ENTER button 4 times. To change the default password.

4. Press the π/† buttons to select PARENTAL, and then press the ® or ENTER button.

5. Press the π/† buttons to select the rating level you want, and then press the ENTER button.

The higher the rating level, the more mature the allowable content.

- If you select the Kid Safe level, discs rated level 2 or higher will not play unless you enter the password.

Security Levels :

❶ KID SAFE ❷ G (General Audiences) : All Ages Admitted ❸ PG (Parental Guidance suggested) : Some material may not be suitable for young children. ❹ PG 13 (PG-13 Parents strongly cautioned) : Some material may be inapproriate for children

under 13.

❺ PGR (Parental Guidance Recommended) : These are not necessarily unsuitable for children, but

viewer discretion is advised, and parents and guardians are encouraged to supervise younger viewers.

❻ R (Restricted) : Under 17 requires accompanying adult ❼ NC17 (NC-17) : No one 17 and under admitted.

❽ ADULT

Note:

- If you have forgotten your password, see “Forgot Password” in the Troubleshooting Guide.

Changing the Password

To change the password, follow these steps:

1. On the Settings Menu, Select Security, and then press the ENTER button.

2. Enter the current 4 digit password. If you have never changed the password, enter the default

password: 0000. To enter a number, use the √/®/π/† buttons to highlight a number, and then press the ENTER button.

3. Select Change Password, and then press the ENTER button.

4. Enter the new 4 digit password. Use the √/®/π/† buttons to select a number, and then press

the ENTER button. Repeat 4 times.

5. Re-enter the new password in the same manner to confirm. The Security menu re-appears.

Setting Up the General Options

1. With the unit in Stop mode, press the MENU button. Press the √/® buttons to select SETTINGS, then press the ENTER button.

2. Press the π/† buttons to select GENERAL, then press the ® or ENTER button.

3. Press the π/† buttons to select the desired item, then press the ® or ENTER button.

Setting Up the Support Options

Support option enable you to check your DVD player information such as the model code, Software Version, The serial and version numbers can be found on the back side of your DVD-

Player.

1. With the unit in Stop mode, press the MENU button. Press the

press the ENTER button.

2. Press the

3. Select PRODUCT INFORMATION, then press the ® or ENTER button.

π/†

buttons to select SUPPORT, then press the ® or ENTER button.

√/®

buttons to select SETTINGS, then

Reference

Troubleshooting

Before requesting service (troubleshooting), please check the following.

Problem Action

The screen is blocked.

Forgot password.

• Press the ®|| button (in front panel) disc inside. All setting will revert to factory settings.

• Press the ®|| button (in front panel) disc inside. All setings including the password will revert to the factory settings. Don't use this unless absolutely necessary.

for more than 5 seconds under no

Spesifications

General

Video Output

Audio Output

Power Requirements

Power Comsumption

Weight

Dimensions

Operating Temperature Range

Operating Humidity Range

Composite Video

Scart Jack

Output terminal

Maximum Output Level

Frequency Response

Digital Audio Out

AC110~240V, 50/60Hz

For the power supply and power consumption, refer to the label attached to the product

1.10 Kg

300mm(W) X 208mm(D) X 42mm(H)

+5ºCto+35ºC

10 % to 75 %

1 channel : 1.0 Vp-p (75 Ω load)

R(Red) : 0.7 Vp-p (75 Ω load) G(Green) : 0.7 Vp-p (75 Ω load) B(Blue) : 0.7 Vp-p (75 Ω load) Composite Video : 1.0 Vp-p (75 Ω load) Luminance Signal : 1.0 Vp-p (75 Ω load) Color Signal : 0.3 Vp-p (75 Ω load)

2 CH

2Vrms

20 Hz to 20 kHz

Coaxial terminal (S/PDIF)

Memo

Contact SAMSUNG WORLD WIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.

Area Contact Centre

ALBANIA 42 27 5755 www.samsung.com AUSTRIA 0810 - SAMSUNG (7267864, € 0.07/min) www.samsung.com

BELGIUM 02-201-24-18

BOSNIA 05 133 1999 www.samsung.com BULGARIA 07001 33 11 www.samsung.com CROATIA 062 SAMSUNG (062 726 7864) www.samsung.com CZECH 800 - SAMSUNG (800-726786) www.samsung.com DENMARK 70 70 19 70 www.samsung.com FINLAND 030 - 6227 515 www.samsung.com FRANCE 01 48 63 00 00 www.samsung.com GERMANY 01805 - SAMSUNG(726-7864 € 0,14/Min) www.samsung.com CYPRUS 8009 4000 only from landline www.samsung.com

GREECE

HUNGARY 06-80-SAMSUNG(726-7864) www.samsung.com ITALIA 800-SAMSUNG(726-7864) www.samsung.com KOSOVO +381 0113216899 www.samsung.com LUXEMBURG 261 03 710 www.samsung.com MACEDONIA 023 207 777 www.samsung.com MONTENEGRO 020 405 888 www.samsung.com NETHERLANDS 0900-SAMSUNG (0900-7267864) (€ 0,10/Min) www.samsung.com NORWAY 815-56 480 www.samsung.com

POLAND

PORTUGAL 808 20-SAMSUNG (808 20 7267) www.samsung.com

ROMANIA

SERBIA 0700 Samsung (0700 726 7864) www.samsung.com SLOVAKIA 0800 - SAMSUNG(0800-726 786) www.samsung.com SPAIN 902 - 1 - SAMSUNG (902 172 678) www.samsung.com SWEDEN 0771 726 7864 (SAMSUNG) www.samsung.com

Switzerland 0848 - SAMSUNG(7267864, CHF 0.08/min)

U.K 0330 SAMSUNG (7267864) www.samsung.com EIRE 0818 717100 www.samsung.com LITHUANIA 8-800-77777 www.samsung.com LATVIA 8000-7267 www.samsung.com ESTONIA 800-7267 www.samsung.com

80111-SAMSUNG (80111 726 7864) only from land line (+30) 210 6897691 from mobile and land line

0 801-1SAMSUNG(172-678) +48 22 607-93-33

08010 SAMSUNG (08010 726 7864) only from landline (+40) 21 206 01 10 from mobile and land line



Web Site

www.samsung.com/be (Dutch) www.samsung.com/be_fr (French)

www.samsung.com

www.samsung.com/ch www.samsung.com/ch_fr (French)

Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate

collection systems)

This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

Correct disposal of batteries in this product (Applicable in the European Union and other European countries with separate

battery return systems.)

This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66.

If batteries are not properly disposed of, these substances can cause harm to human health or the environment.

To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery return system.

AK68-02198A-00

DVD Player

Bedienungsanleitung

Erleben Sie die Möglichkeiten

Vielen Dank, dass Sie sich für dieses Produkt von Samsung entschieden haben. Um unseren umfassenden Service nutzen zu können, registrieren Sie Ihr Produkt unter

www.samsung.com/register

DVD-E360K DVD-E360 DVD-E350

DEUTSCH

Vorsichtsmaßnahmen

1. Gerät aufstellen

Die korrekte Betriebsspannung für den Player ist auf dem Etikett an der Rückseite des Gerätes angegeben.

Platzieren Sie den Player in einem Schrank mit ausreichend Platz zur Belüftung (7~10 cm). Die Belüftungsöffnungen an den

Gerätekomponenten dürfen nicht verdeckt werden.

- Schieben Sie das CD-Fach nicht mit der Hand ein.

Stapeln Sie die Komponenten nicht übereinander.

- Schalten Sie alle Komponenten aus, bevor Sie den Player transportieren oder bewegen.

- Wenn Sie andere Komponenten an diesen Player anschließen, müssen diese vorher abgeschaltet werden.

- Nach Gebrauch muss die DVD aus dem CD-Fach entnommen und der Player abge

schaltet werden. Dies gilt insbesondere,

wenn der Player längere Zeit nicht verwen

det wird.

- Der Netzstecker dient zum Trennen des Geräts vom Stromnetz und sollte daher jed erzeit leicht zugänglich sein.

2. Sicherheitshinweise

- In diesem Produkt kommt ein Laser zum

Einsatz. Bei Verwendung von Befehlen und Einstellungen sowie bei Vorgehensweisen, die von den Anweisungen dieses

Handbuchs abweichen, kann der Benutzer gefährlicher Strahlung ausgesetzt werden.

Öffnen Sie keine Gehäuse und führen Sie

keine Reparaturarbeiten selbst aus. Lassen Sie Reparaturen stets von qualifiziertem Fachpersonal durchführen.

3. Vorsicht

- Der Player ist nicht für den gewerblichen

Einsatz vorgesehen. Verwenden Sie dieses Produkt nur für den privaten Bereich.

- Achten Sie darauf, dass das Gerät nicht

mit flüssigkeiten bespritzt werden kann. Auf dem Gerät dürfen daher keine Behälter mit

flüssigkeit (z, B. Blumensaven) abgestellt werden.

- Äußere Einflüsse wie Blitzschlag oder

elektrostatische Aufladung können den nor

malen Betrieb das Players beeinträchtigen.

Schalten Sie in diesem Fall den Player mit

der Taste POWER aus und wieder ein, oder

ziehen Sie den Netzstecker aus der Steckdose und stecken Sie ihn anschließend wieder ein. Anschließend funktioniert der

Player wieder normal.

Wenn bei plötzlichen temperaturveränderungen

im Inneren des Players Feuchtigkeit kondensiert, kann die Funktion des Players beeinträchtigt werden.Bewahren Sie in diesem Fall den Player so lange bei Zimmertemperatur auf, bis das Innere vollständig getrocknet ist und

das Gerät wieder normal betrieben werden kann.

4. CDs/DVDs

- Zur Reinigung von CDs/DVDs dürfen kein CD-Reinigungsspray, kein Benzol, kein Verdünner und keine anderen flüchtigen Lösungsmittel verwendet werden, da diese Substanzen die Oberfläche von CDs/DVDs beschädigen könnten.

- Berühren Sie niemals die Datenseite von CDs/DVDs. Fassen Sie CDs/DVDs an den

Rändern oder am Rand und dem Mittelloch an.

- Entfernen Sie Schmutz vorsichtig mit einem Tuch. Wischen Sie dabei niemals mitVor wärts- und Rückwärtsbewegungen über CDs/DVDs

5. Entsorgung und Umweltschutz

- Die in diesem Produkt verwendete Batterie

enthält umweltschädliche Chemikalien.

- Entsorgen Sie die Batterien deshalb

umweltgerecht und entsprechend der behördlichen Bestimmungen.

Die zu diesem Benutzerhandbuch gehörige Produkteinheit ist unter geistigen Eigentumsrechten Dritter lizenziert. Diese Lizenz beschränkt sich auf die private, nicht gewerbliche Verwendung durch Endbenutzer und auf die in dieser Lizenz enthaltenen Inhalte. Die gewerbliche Verwendung ist nicht gestattet. Die Lizenz gilt ausschließlich für diese Produkteinheit und umfasst keine unlizenzierten oder den Normen ISO/IEC 11172-3 oder ISO/IEC 13818-3 entsprechenden Produkteinheiten oder Verfahren, die zusammen mit dieser Produkteinheit verwendet oder verkauft werden. Die Lizenz gilt lediglich für die Verwendung dieser Produkteinheit zum Kodieren und/oder Dekodieren von Audiodateien, die den NormenISO/IEC 11172-3 oder ISO/IEC 13818-3 entsprechen. Unter dieser Lizenz werden keine Rechte an Leistungsmerkmalen und Funktionen von Produkten vergeben, die diesen Normen nicht entsprechen.

VORSICHT: BEI VERWENDUNG VON BEFEHLEN UND EINSTELLUNGEN SOWIE BEI VORGEHENSWEISEN, DIE VON DIESEM HANDBUCH ABWEICHEN, KANN DER BENUTZER GEFÄHRLICHER STRAHLUNG AUSGESETZT WERDEN.

Inhaltsver zeichnis

Vorsichtsmaßnahmen . . . . . . . . . . . . . . . . . . . . . 2

Einführung

Allgemeine Funktionen . . . . . . . . . . . . . . . . . . . . 2

Beschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Überblick über die Fernbedienung . . . . . . . . . . . 4

Anschlüsse

Anschlüsse wählen . . . . . . . . . . . . . . . . . . . . . . . 4

Grundfunktionen

DVDs wiedergeben . . . . . . . . . . . . . . . . . . . . . . . 5

Such- und SKIP-Funktionen verwenden . . . . . . 5

Anzeigefunktion verwenden . . . . . . . . . . . . . . . . 5

Disc- und Titelmenü verwenden . . . . . . . . . . . . 6

Wiedergabe wiederholen . . . . . . . . . . . . . . . . . . 6

Zeitlupe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Erweiterte Funktionen

Bildformat anpassen (EZ VIEW) . . . . . . . . . . . . . 6

Audio-Sprache wählen . . . . . . . . . . . . . . . . . . . . 6

Untertitel-Sprache wählen . . . . . . . . . . . . . . . . . . 7

Kamerawinkel ändern . . . . . . . . . . . . . . . . . . . . . 7

Lesezeichen-Funktion verwenden. . . . . . . . . . . . 7

Zoom-Funktion verwenden . . . . . . . . . . . . . . . . . 7

Clip-Menü für MP3/WMA/JPEG/MPEG4/

CD Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Einführung

Allgemeine Funktionen

Exzellenter Sound

Dolby Digital, eine von Dolby Laboratories entwickelte Technologie, garantiert eine kristallklare Tonwiedergabe.

Bildschirm

Filme können sowohl im normalen als auch im Breitbild-Format wiedergegeben werden.

Zeitlupe

Wichtige Szenen können in Zeitlupe wiedergegeben werden.

Kindersicherung (DVD)

Durch Wahl eines geeigneten Sicherheitsniveaus der Kindersicherung kann der Benutzer verhindern, dass Kinder jugendgefährdende Filme auf dem Gerät abspielen.

Verschiedene BildschirmmenüFunktionen

Sie können bei der Wiedergabe von Filmen zwischen verschiedenen Sprachen (Audio/ Untertitel) und Kamerawinkeln wählen.

EZ VIEW (DVD)

Mit Easy View kann das Bild an das

Ordner auswählen . . . . . . . . . . . . . . . . . . . . . . . . 7

MP3/WMA/CD Audio-Dateien wiedergeben . . . . 7

MPEG4-Dateien wiedergeben . . . . . . . . . . . . . . . 8

Multimedia-Dateien von einem USB-Gerät

abspielen (Nur DVD-E360K, E360) . . . . . . . . . . . 9

CD kopieren (Nur DVD-E360K, E360) . . . . . . . . 10

Picture CD wiedergeben . . . . . . . . . . . . . . . . . . 10

Karaoke-funktionen (Nur DVD-E360K)

Karaoke-funktionen . . . . . . . . . . . . . . . . . . . . . . 11

Setup-Menü ändern

Setup-Menü verwenden . . . . . . . . . . . . . . . . . . 11

Anzeigeoptionen einstellen . . . . . . . . . . . . . . . . 11

Tonwiedergabeoptionen einstellen . . . . . . . . . . 12

Einrichten des Systemoptionen . . . . . . . . . . . . 12

Sprachfunktionen einstellen . . . . . . . . . . . . . . . 12

Einrichten der Sicherheitsoptionen . . . . . . . . . . 12

Einrichten der Allgemeinen Optionen . . . . . . . . 13

Einrichten des Support-Optionen . . . . . . . . . . . 13

Weitere Informationen

Fehlersuche . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Technische Daten . . . . . . . . . . . . . . . . . . . . . . . 14

Bildseitenverhältnis Ihres Fernsehgeräts angepasst werden (16:9 oder 4:3).

Digitaler Foto-Betrachter (JPEG)

Sie können digitale Fotos auf dem Fernsehgerät wiedergeben.

Wiederholen

Sie können ein Musikstück oder Film einfach wiederholen lassen, indem Sie die Taste REPEAT drücken.

MP3/WMA

Mit diesem Gerät können DVDs mit MP3- oder WMA-Dateien wiedergegeben werden.

MPEG4

Diese Funktion dient der Wiedergabe von MPEG4-Daten innerhalb einer AVI-Datei.

CD kopieren (Nur DVD-E360K, E360)

Mit dieser Funktion können Sie Audiodateien von CD im MP3-Format auf ein USB-Gerät kopieren. (Nur Audio-CD (CD-DA)).

Hinweis

- Datenträger, die nicht auf diesem Player

abgespielt werden können.

▼

▼ ▼

▼

 •DVD-ROM •DVD-RAM  •CD-ROM  •CDV  •CDI  •CVD

- Ob die Wiedergabe möglich ist, hängt von den Aufnahmebedingungen ab.

 •DVD-R,+R  •CD-RW  •DVD+RW,-RW(V-Modus)

- Abhängig von Datenträgertyp und

Aufnahmebedingungen können bestimmte CD-Rs, CD-RWs und DVD-Rs mögli cher weise nicht auf dem Gerät wiedergegeben werden.

Kopierschutz

Viele DVD sind durch Kodierung gegen Kopieren geschützt. Deshalb sollten Sie den DVD-Player nur direkt an das Fernsehgerät, und nicht über den Videorekorder anschließen. Bei DVDs mit Kopierschutz erzeugt die Wiedergabe über Videorekorder ein verzerrtes Bild.

Diese Gerät umfasst Kopierschutz-Technologie, die durch US-Patente und andere geistige Eigentumsrechte der ROVI Corporation geschützt ist. Reverse Engineering und Disassemblierung sind nicht gestattet.

CLASS 1 LASER PRODUCT

Dieses Compact Disk Gerät ist als CLASS 1 LASER Produkt eingestuft. Die Verwendung von anderen Bedienelementen, Einstellungen oder die Durchführung von Prozeduren die von denen hier angegebenen abweichen, können zu einer zu einer gefährlichen Strahlenbelastung führen.

ACHTUNG :

NACH DEM ÖFFNEN SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG DER KLASSE 3B. EINWIRKUNG DES STARHLS VERMEIDEN (IEC 60825-1).

DIESES GERÄT VERWENDET EINEN LASER : DIE VERWENDUNG VON ANDEREN BEDIENELEMENTEN, EINSTELLUNGEN ODER DIE DURCHFÜHRUNG VON PROZEDUREN DIE VON DENEN HIER ANGEGEBENEN ABWEICHEN, KÖNNEN ZU EINER ZU EINER GEFÄHRLICHEN STRAHLENBELASTUNG FÜHREN. DAS GEHÄUSE NICHT ÖFFNEN UND KEINE REPARATUREN SELBST DURCHFÜHREN. QUALIFIZIERTES PERSONAL MIT DER WARTUNG BEAUFTRAGEN

CLASS 1 LASER PRODUCT KLASSE 1

LASER PRODUKT LASER LAITE LASER APPARAT

LÁSER CLASE 1

LUOKAN 1 KLASS 1 PRODUCTO

Symbole

DVD-Regionalcodes

PAL-Fernsehsystem in Großbritan-

PAL

nien, Frankreich, Deutschland etc.

Dolby Digital-Ton

STEREO

Stereoaufnahme

DIGITAL

Digital Audio disc

SOUND

MP3-disc

Regionalcodes

DVD-Player und DVDs sind nach Regionen codiert. Für die Wiedergabe müssen die Codes von Player und Datenträger zusammenpassen. Wenn dies nicht der Fall ist, kann der Datenträger nicht wiedergegeben werden. Der für diesen Player erforderliche Regionalcode ist auf der Rückseite des Gerätes beschrieben.

DivX-Zertifizierung

DivX®, DivX Certified® und die dazugehörigen Logos sind Markenzeichen von Rovi Corporation oder ihrer Tochtergesellschaften und sind urheberrechtlich geschützt. Dieses Gerät

ist offiziell DivX zertifiziert® und gibt DivX-Videos wieder. Nähere Informationen und Softwareanwendungen zum Konvertieren Ihrer Videodateien in DivX Videos finden Sie unter www.divx.com. INFOS ZU DIVX VIDEO-ON-DEMAND: Dieses DivX Certified® Gerät muss registriert werden, damit Video-On-Demand-Inhalte (VOD) wiedergegeben werden können. Um den Registrierungscode zu erzeugen, wechseln Sie in den DivX VOD-Bereich im Setup-Menü des Geräts. Besuchen Sie vod.divx.com für weitere Informationen über den Abschluss der Registrierung.

INFOS ZU DIVX VIDEO: Bei DivX® handelt es sich um ein von DivX, LLC, einem Tochterunternehmen von Rovi Corporation, entwickeltes, digitales

Videoformat.

DivX-Certified® für die Wiedergabe von DivX®

-Videos, einschließlich Premium-Inhalt. Geschützt durch eines oder mehrere der folgenden US-Patente: 7,295,673; 7,460,668; 7,515,710; 7,519,274.

Beschreibung

Bedienelemente an der Vorderseite

DVD-E360K

DVD-E360

DVD-E350

1. DISC-FACH

Legen Sie hier den Datenträger ein.

2. DISPLAY

Hier werden Informationen zum Betrieb

angezeigt.

3. OPEN/CLOSE ( )

Drücken Sie diese Taste, um das CD-Fach

zu öffnen und zu schließen.

4. PLAY/PAUSE ( )

Wiedergabe starten oder unterbrechen.

5. POWER ON/OFF ( )

Wenn der Player auf ein/aus gestellt

wurde, ist er ein- oder ausgeschalten.

6. USB-Host (Nur DVD-E360K, E360)

Zum Anschließen externer Speichergeräte

wie digitale Standbildkameras, MP3Player, Memory Sticks oder Kartenleser. Lautstärke einzustellen, drehen Sie den Regler nach links oder rechts.

7. MIC (Nur DVD-E360K)

Schließen Sie zum Verwenden der

Karaoke-Funktionen das Mikrofon an.

Überblick über die Fernbedienung

DVD-E360K

2 3

5 6

1. Taste DVD POWER

Zum Ein- und Ausschalten des DVD-Players.

2. Taste REPEAT

Mit dieser Taste können Titel, Kapitel, Tracks

oder Datenträger wiederholt wiedergegeben werden.

3. Taste DISC MENU

Disc-Menü anzeigen.

4. Taste RECORD

(Nur DVD-E360K)

Verwendung für Karaoke-Aufnahmen.

5. Die Tasten SUCHEN (k/K)

Mit diesen Tasten kann der Datenträger vor-

wärts/rückwärts durchsucht werden.

6. Taste STOP (■)

7. Die Tasten SKIP (|k/K|)

Mit der SKIP-Taste können Sie zwischen

Titeln, Kapiteln oder Tracks springen.

8. Taste MENU

DVD-Player-Menü anzeigen.

9. Tasten ENTER/π†√®

Optionen auswählen.

10. Taste AUDIO (√)

Zur Auswahl der verschiedenen Audio-

Funktionen, die vom eingelegten Datenträger unterstützt werden.

11. Taste TOOLS

12 13

14 15

17 18

DVD-E360

1 2

5 6 7

Aktuellen Disc-Modus anzeigen. Zur Anzeige

12. Taste OPEN/CLOSE ( )

Disc-Fach öffnen und schließen.

13. Taste VIDEO SEL.

Videoausgangsmodus ändern.

14. Taste USB (Nur DVD-E360K, E360) Zum Vergrößern des DVD

15.

Finden Sie schnell Lesezeichenabschnitte

16. Taste PLAY

Wiedergabe starten.

17. Taste SUBTITLE/

18. Taste RETURN

Zum vorherigen Menü zurückkehren.

19.

20. Taste KARAOKE (†) (Nur DVD-E360K) Zum Zugriff auf das Karaoke-Menü

21. Taste INFO

22. (Nur DVD-E360, E350)

DVD-E350

6 7

der Info-Anzeige Wiedergabe (Playback).

Taste MARKER

einer DVD.

( )

(π)

Taste TITLE MENU

Title-Menü anzeigen.

(®)

(Tastensteuerung, Mikrofonlautstärke, Echo).

Zum Aufrufen der Funktion Anzeige (Display).

Taste REPEAT A-B

Zur wiederholen Wiedergabe eines gewählten

Abschnitts A-B.

23. Taste ZOOM (Nur DVD-E350)

Anschlüsse

Anschlüsse wählen

12 13

Im Folgenden werden Beispiele gezeigt, die demonstrieren, wie der DVD-Player an Fernsehgeräte und

andere Komponenten angeschlossen werden kann.

Vor dem Anschließen des DVD-Players

Schalten Sie den DVD-Player, das Fernsehgerät und sonstige Komponenten stets aus, bevor Sie Kabel

anschließen oder entfernen.

17 18

- Weitere Informationen zu den Komponenten, die Sie anschließen möchten (z. B. Fernsehgeräte), finden Sie in der Bedienungsanleitung des entsprechenden Gerätes.

A. An Fernsehgerät anschließen (Video CVBS)

- Verbinden Sie über Video-/Audiokabel die VIDEO OUT-Anschlüsse (gelb) / AUDIO OUTAnschlüsse (rot und weiß) auf der Rückseite des DVD-Players mit den VIDEO IN-Anschlüssen (gelb) / AUDIO INAnschlüssen (rot und weiß) des Fernsehgerätes.

- Schalten Sie DVD-Player und Fernsehgerät ein.

- Drücken Sie auf der Fernbedienung des Fernsehgerätes die Taste zur Auswahl der Eingangsquelle, bis das Video-Signal des DVD-Players auf dem TV-Bildschirm angezeigt wird.

Hinweis

Wenn Audiokabel und Netzkabel zu nahe aneinander liegen, kann es zu Signalstörungen kommen.

- Informationen zum Anschließen eines Verstärkers finden.

- Die Anzahl und Lage der Anschlüsse kann je nach Fernsehgerät unterschiedlich sein. Informationen dazu finden Sie in der Bedienungsanleitung des Fernsehgerätes.

- Falls das Fernsehgerät nur über eine Audio-Eingangsbuchse verfügt, verbinden Sie diese mit dem [AUDIO OUT]-[links]-Anschluss (weiß) des DVD-Players.

- Wenn Sie die VIDEO SEL.-Taste drücken während sich der DVD-Spieler im Stopp-Modus befindet oder keine DVD eingelegt ist, wechselt der Videoausgabemodus in dieser Reihenfolge: (SCART-RGB ➝ SCART-CVBS).

B. An ein Audiogerät anschließen (2-Kanal, Dolby Digital-, MPEG2)

- Verbinden Sie mit Hilfe der Audiokabel die AUDIO OUT Anschlüsse (rot und weiß) auf der Rückseite des DVD Players mit den AUDIO IN-Anschlüssen am Verstärker.

- Bei Verwendung eines Koaxialkabels verbinden Sie dieses mit dem Anschluss DIGITAL AUDIO

OUT (COAXIAL) an der Rückseite des DVD-Players mit dem Anschluss DIGITAL AUDIO IN (COAXIAL) am Verstärker.

- Schalten Sie DVD-Player, Fernsehgerät und Verstärker ein.

- Wählen Sie am Verstärker über die Taste zur Aus wahl der Eingangsquelle die Option Externer Eingang, damit das Tonsignal des DVD-Players wiedergegeben wird. Informationen zur Auswahl des Audio-Eingangs an Ihrem Verstärker finden Sie in dessen Bedienungsanleitung.

C. An ein Fernsehgerät anschließen (SCART)

- Verbinden Sie über scart kabel die SCART auf der Rückseite des DVD-Players mit den SCART IN des Fernsehgerätes.

- Schalten Sie DVD-Player und Fernsehgerät ein.

- Drücken Sie auf der Fernbedienung des Fernsehgerätes die Taste zur Auswahl der Eingangsquelle, bis das Video-Signal des DVD-Players auf dem TV-Bildschirm angezeigt wird.

+ 44 hidden pages