5. Disassembly and Reassembly
5-1 Cabinet and PCB
5-1-1 Door-Tray Removal
1)Supply power and open Tray Œ.
2)Disassemble the Door-Tray ´ in direction of arrow “A”.
3)Close Tray Œ and power off.
Note : If Tray Œ doesn’t open, insert a Screw driver ¨ into the Emergency hole ˇ(as shown in detailed drawing) and then turn it in the direction of arrow “B”. Open Tray manually.
ŒTRAY
´ DOOR-TRAY
"A"
ˇ EMERGENCY HOLE
"B"
¨SCREW DRIVER
<Bottom View>
Fig. 5-1 Door-Tray Removal
Samsung Electronics |
5-1 |
Disassembly/Reaasembly
5-1-2 Top Cabinet Removal
1)Remove 3 Screws Œ on the back Top Cabinet.
2)Remove 2 Screws ´, ˇ on the left and right side.
3)Lift up the Top Cabinet in direction of arrow.
Œ 3 SCREWS
´ 1 SCREW
ˇ 1 SCREW
Fig. 5-2 Top Cabinet Removal
5-2 |
Samsung Electronics |
Disassembly/Reaasembly
5-1-3 Ass’y Front-Panel, Phone/Power PCB, Play PCB Removal (DVD-909)
1)Remove 2 Screws Œ and Ass’y Front Panel ´.
2)Remove Knob-Volume ˇ and 2 Screws ¨.
3)Remove Bracket-Phone ˆ and Phone/Power PCB Ø.
4)Remove Knob-Jog and Knob-Shuttle ”.
5)Remove 4 Screws ’ and Play PCB ˝.
¨2 SCREWS
Œ2 SCREWS
ˆBRACKET-PHONE
ØPHONE/POWER PCB
|
’4 SCREWS |
ˇKNOB-VOLUME |
˝PLAY PCB |
|
´ASS'Y FRONT-PANEL
”KNOB-SUHTTLE
KNOB -JOG
Fig. 5-3 Ass’y Front-Panel, Phone/Power PCB, Play PCB Removal (DVD-909)
Samsung Electronics |
5-3 |
Disassembly/Reaasembly
5-1-4 Ass’y Front-Panel, Power PCB, Play PCB Removal (DVD-709)
1)Remove 2 Screws Œ and Ass’y Front Panel ´.
2)Remove 2 Screws ˇ and Power PCB ¨.
3)Remove 3 Screws ˆ and Play PCB Ø.
Œ2 SCREWS
ˇ2 SCREWS
¨POWER PCB
ˆ3 SCREWS
ØPLAY PCB
´ASS'Y FRONT-PANEL
Fig. 5-4 Ass’y Front-Panel, Power PCB, Play PCB Removal (DVD-709)
5-4 |
Samsung Electronics |
Disassembly/Reaasembly
5-1-5 Main PCB, Jack PCB Removal (DVD-909 NTSC MODEL)
1)Remove 4 Screws Œ and 5 Screws ´.
2)Lift up the Jack PCB ˇ.
3)Remove 3 Screws ¨ and lift up the Main PCB ˆ.
Œ4 SCREWS
ˇJACK PCB
¨3 SCREWS
ˆMAIN PCB
´5 SCREWS
Fig. 5-5 Main PCB, Jack PCB Removal (DVD-909 NTSC MODEL)
Samsung Electronics |
5-5 |
Disassembly/Reaasembly
5-1-6 Main PCB, Jack PCB Removal (DVD-709 NTSC MODEL)
1)Remove 4 Screws Œ and 1 Screw ´.
2)Lift up the Jack PCB ˇ.
3)Remove 3 Screws ¨ and lift up the Main PCB ˆ.
Œ4 SCREWS
ˇJACK PCB
¨3 SCREWS
ˆMAIN PCB
´1 SCREW
Fig. 5-6 Main PCB, Jack PCB Removal (DVD-709 NTSC MODEL)
5-6 |
Samsung Electronics |