Samsung DV2A INSTALLATION INSTRUCTIONS AND OPERATION MANUAL
side vent kit installation instructions
Description: Exhaust kit for venting left and right side, or base
DC68-01052Y-05_EN
CHECKING THE INSTALLATION PARTS
Side Vent Kit Includes:
Vent cap Elbow Duct Front Duct Front-
Bottom
Attached label help you recognize each duct.
To avoid risk of electrical shock, personal injury or death; disconnect electrical power before servicing
WARNING
Wear eye protection before performing this installation
CAUTION
Duct Back-Left Duct Back-Right Manual
PROCEDURE
The following instruction covers exhausting a dryer either through the left or right side of the cabinet, or through the base. It is recommended a
qualified Service Technician do the installation of this kit and dryer.
INSTALLING THE SIDE VENT KIT
1. For easier installation, removing the front assembly, tumbler and drive belt is recommended.
* Refer to service manual for disassembly and reassembly of dryer
2. Remove the knockout from either of the left or right side panel, or base. Strike it with a hammer and chisel
very close to the seam. One to three sharp blows will remove it. Do not strike the middle of the knockout.
WARNING: Wear safety glasses.
3. Remove the exhaust duct cover. (Type B only)
Type A
4. Remove the old exhaust duct from blower housing.
Type A
5. Raise guide plate to about 90 degree, using a flat-blade screwdriver.
The guide plate will support the exhaust duct(f).
DV-1A_XAA-01052Y-05_EN.indd 1 2016-01-29 �� 12:37:52
Type B
Type B
FOR LEFT AND RIGHT SIDE
FOR BOTTOM PLATE
6. Insert new exhaust Duct Front
supplied with kit into blower
housing. Rotate the duct to
engage duct clip into tab
extending up from base frame.
7. Insert the elbow supplied in
the kit into exhaust duct (F)
and through the left or the right
(Electric models only) toward the
outlet hole depending on which
direction to be exhausted.
8. For side venting (left or right)
insert the Exhaust Duct Back into
the elbow and out cabinet side.
6. Assemble The Duct Front-Bottom
and The Elbow.
7. Insert the assembled elbow and
duct into the hole at the bottom
as shown by the figure.
8. Pull the Duct Front-Bottom
forwards to insert it into the Fan
Housing.
9. Put the duct over on the tab
extended from the base frame.
For left side venting use “Duct
Back-Left”, for right side venting
use “Duct Back-Right” separately.
For these models DV56H9000E*, DV56H9100E*, use the “Duct-
Back Left” (BACK-LEFT) instead of “Duct-Back Right” for RIGHT
SIDE VENTING.
9. Tape each joint with the duct tape.
Caution: Internal duct joints must be secured with tape;
otherwise, they may separate and cause a safety hazard.
10. Drill a 1/8˝ hole using a hand drill
in the frame and fix the bracket of
the duct by fastening the screw.
The screw is not supplied with the
kit. You may use the screw that
you remove in the step 3.
11. Reinstall the exhaust duct cover
on rear of cabinet.
12. Insert the vent cap supplied with
the kit into rear exhaust hole left
by old duct.
Type A
10. Wrap up the joint with duct tape.
11. Tape on the joint between the
elbow and internal duct.
Caution: Internal duct joints must be secured with tape;
otherwise, they may separate and cause a safety hazard.
12. Reinstall the exhaust duct cover
on rear of cabinet.
13. Insert the vent pipe cap supplied
with the kit into rear exhaust hole
left by old duct.
Type A
Type B
Type B
DV-1A_XAA-01052Y-05_EN.indd 2 2016-01-29 �� 12:37:56
Loading...