Samsung DRMODEMZ1 User Manual
DR-Ready modem
User manual
imagine the possibilities
Thank you for purchasing this
Samsung product. To receive a
more complete service, please
register your product at
www.samsung.com/register
FEDERAL COMMUNICATION COMMISSION INTERFERENCE
STATEMENT
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment o and on, the user is encouraged to try to correct the
interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20 cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
QUESTIONS OR COMMENTS?
COUNTRY CALL OR VISIT US ONLINE AT
U.S
CANADA
800-SAMSUNG
(800-726-7864)
800-SAMSUNG
(800-726-7864)
www.samsung.com
www.samsung.com/ca
Code No.: DC68-00000A_EN
Safety information
WARNING
The DR-Ready modem only works for the following Samsung models.
Since the modem can only be installed in the following models, please
confirm that your product is one of the following models.
• Refrigerator: RF4289HARS, RSG309AARS
• Washer/Dryer: WF461ASP/XAA / DV431ASP/XAA
• Dishwasher: DMT-611
WHEN INSTALLING YOUR DR-READY MODEM
Do not install the modem on an unstable surface.
• If the product falls, it may result in injury or damage to property.
Do not install the modem near a heater, volatile substance (oil, etc.) or
inflammable material.
• This may result in electric shock or fire.
Do not install the modem in a humid or dusty location, a location
exposed to direct sunlight water (rain drops, etc.), or a location where
gas may leak.
• This may result in electric shock or fire.
To reinstall the modem, contact the service center.
WHEN USING YOUR DR-READY MODEM
Do not connect the DR-Ready modem to an incompatible product.
• This may result in a problem or product malfunction.
If the modem generates a strange sound, smell or smoke, remove the
modem from the product immediately, disconnect the LAN cable and
contact the service center.
• Failing to do so may result in electric shock or fire.
If the modem becomes flooded, immediately remove the modem
from the product, disconnect the LAN cable and contact the service
center.
• This may result in electric shock or fire.
If water or a foreign object enters the modem, immediately remove
the modem from the product (refrigerator, washer or dishwasher),
disconnect the LAN cable and contact the service center.
• Failing to do so may result in electric shock or fire.
Do not touch the modem or LAN cable with wet hands.
• This may result in electric shock, fire or injury.
Do not intentionally apply excessive force to the modem.
• This may result in a problem with or damage to the product.
Do not disassemble, repair or modify the modem yourself.
• This may result in electric shock, fire, damage to the product or
injury.
Do not step on the modem or place an object (laundry, lighted candle,
lighted cigarette, dish, chemical, metal object, etc.) on the modem.
• This may result in a problem with or damage to the product.
Do not use a sharp object with the modem.
• This may result in a problem with or damage to the product.
CERTIFICATION
• FCC: A3L-DRMODEMZ1
• ZigBee: ZIG11004ZSE26067-24
Setting up your DR-Ready modem
CHECKING THE PARTS
Front panel Rear panel
Packaging contents
DR-Ready modem
(1)
Since there is a magnet at the bottom of the modem, you can
easily fix it to the metal part of the product.
1.5 m direct LAN
cable (1)
User manual (1)
Power
INSTALLING YOUR DR-READY MODEM IN YOUR
REFRIGERATOR
DR-Port
1. Enter the MAC and PIN numbers on the label attached to the
bottom of the modem into your DRC. (For the procedures to enter
the MAC and PIN numbers, refer to the DRC user manual.)
2. Open the rubber cover of the DR-port at the back of your
refrigerator and connect the LAN cable supplied with the modem
to the DR-port.
For the exact position of the DR-port, refer to the user
manual for the corresponding refrigerator.
3. Close the cover.
4. Connect the other end of the direct LAN cable to the Host I/F port
of the modem.
5. Check the connection. (Refer to the “Confirming the connection”
section.)
6. Attach the modem to the top or side of the refrigerator.
INSTALLING YOUR DR-READY MODEM IN YOUR
WASHER OR DRYER
DR-Port
1. Enter the MAC and PIN numbers on the label attached to the
bottom of the modem into your DRC. (For the procedures to enter
the MAC and PIN numbers, refer to the DRC user manual.)
2. Open the rubber cover of the DR-port at the back of your washer
or dryer and connect the LAN cable supplied with the modem to
the DR-port.
For the exact position of the DR-port, refer to the user
manual for the corresponding washer or dryer.
3. Close the cover.
4. Connect the other end of the direct LAN cable to the Host I/F port
of the modem.
5. Check the connection. (Refer to the “Confirming the connection”
section.)
6. Attach the modem to the top or side of the washer or dryer.
INSTALLING YOUR DR-READY MODEM IN YOUR
DISHWASHER
DR-Port
Kickplate
1. Enter the MAC and PIN numbers on the label attached to the
bottom of the modem into your DRC. (For the procedures to enter
the MAC and PIN numbers, refer to the DRC user manual.)
2. Remove the kickplate at the bottom of your dishwasher.
3. Open the rubber cover of the DR-port at the bottom of your
dishwasher and connect the LAN cable supplied with the modem
to the DR-port.
For the exact position of the DR-port, refer to the user
manual for the corresponding dishwasher.
4. Close the cover.
5. Connect the other end of the direct LAN cable to the Host I/F port
of the modem.
6. Check the connection. (Refer to the “Confirming the connection”
section.)
7. Attach the modem to the bottom of the dishwasher and install the
kickplate.
DR-Ready_Modem_EN.indd 1 2011-05-27 �� 5:15:59
Setting up your DR-Ready modem
CONFIRMING THE CONNECTION
1. Turn on the power of the product (refrigerator, washer, dryer or
dishwasher) where the modem has been installed.
2. Connect the direct LAN cable to the modem’s Host I/F port. The
Power LED of the modem is lit.
CONNECTING MULTIPLE MODEMS
The ability of the DR-Ready modem to communicate may be impaired
depending on the operating environment (distance, obstacles,
interference, etc.). If the communication quality is insucient, you can
solve the problem by connecting more than one DR-Ready modem or
connecting a specialized modem.
Connecting DR-Ready modems
The following is the way to communicate with the DRC via a modem
that is installed in another product (refrigerator, washer, dryer or
dishwasher).
Using a specialized modem
The following is the way to communicate with the DRC via a
specialized modem.
Modem
DRC
3. The Pairing LED of the modem blinks at 0.5 second intervals for
up to 10 seconds while attempting to connect to the DRC.
If the auto connection process has failed, set the DRC to
allow connections and press the modem Pairing button to
connect them manually. When it attempts to connect, the
Pairing LED starts blinking at a 0.5 second interval and then
blinks at a 1 second interval for up to 25 seconds. (For the
procedures to set the DRC to allow connections, refer to the
DRC user manual.)
4. When the connection is established, the Pairing LED is lit.
While the DRC is transmitting the DR level, any one of
the Level 1, 2, 3 and 4 LEDs can be turned on after the
connection.
DRC ModemModem
Modem
Star Topology Tree Topology
• A maximum 3 tree depth is
supported.
• Up to 10 modems can be
connected to the DRC.
• Up to 10 modems can be
connected to the DRC.
(Including all the modems
used to construct the tree
topology.)
Modem
(Depth 1)
Modem
(Depth 2)
• Modem-A: An existing DR-Ready modem that is installed in
• Modem-B: The DR-Ready modem that is installed in the product
1. Enter the MAC and PIN numbers of Modem-B into the DRC.
2. Connect Modem-B to the product you want to use.
3. Press the Pairing button of Modem-A. The Pairing LED blinks at
4. Press the Pairing button of Modem-B. The Pairing LED blinks
5. When Modem-B is connected with Modem-A, the Pairing LED of
6. When the DRC is transmitting the DR level, the same DR level as
DRC Modem-A Modem-B
another product.
you want to use.
1 second intervals.
at 0.5 second intervals and Modem-B attempts to connect with
Modem-A.
Modem-B is lit.
that of Modem-A is displayed on Modem-B.
You have to purchase the specialized modem additionally.
1. Enter the MAC and PIN numbers of the DR-Ready modem into the
DRC.
2. Connect the DR-Ready modem to the product you want to use.
3. Supply power to the specialized modem using the Samsung
adapter (ATADU43KBK).
4. Press the Pairing button of the specialized modem. The Pairing
LED blinks at 1 second intervals.
5. Press the Pairing button of the DR-Ready modem. The Pairing
LED blinks at 0.5 second intervals and the DR-Ready modem
attempts to connect with the specialized modem.
6. If the DR-Ready modem is connected to the specialized modem,
the Pairing LED of the DR-Ready modem is lit.
5. If you cannot make a connection, contact the service center.
Using your DR-Ready modem Troubleshooting Appendix
USING THE REAR PANEL
1 2 3 4
1
Reset button
2
Host I/F port
3
Pairing button
Power
4
terminal
Press this button to reset the modem to
the factory default settings.
This port is used to connect to a product
with the direct LAN cable.
Press this button to make or remove a
connection to the DRC or gateway.
This is the port to connect an adapter
when using the modem by itself.
Use only an ATADU32KBK adapter.
Power
CHECKING THE LED
1
2
3
4
5
6
1 2 3 4 5 6
Power LED (Green, ON/OFF)
Demand Response Level1 Indication LED
(Green, ON/OFF)
Demand Response Level2 Indication LED
(Green, ON/OFF)
Demand Response Level3 Indication LED
(Green, ON/OFF)
Demand Response Level4 Indication LED
(Green, ON/OFF)
Chip LED (Green)
• ON: When the modem is connected to
the DRC or gateway.
• Blinking at a 1 second interval: When
the modem is waiting to Pair or is
exchanging the security key.
• Blinking at 0.5 second intervals: When
the modem is attempting to pair.
• OFF: When the modem is not
connected to the DRC or gateway.
TROUBLESHOOTING
Problem Solution
• Check if the product is connected to the
power source.
The modem is
not turned on.
The Pairing LED
is turned o or
all the Level 1, 2,
3 and 4 LEDs are
turned on.
Both Level 1
and 2 LEDs are
turned on.
• Check if the DR-Ready modem is properly
connected to the product with the direct
LAN cable.
• In the case of a specialized modem, check
if the adapter is connected.
• Check if the DRC in your house is working
properly.
• Check that the DRC is turned on.
• Check if the modem’s MAC and PIN
numbers have been entered into the DRC
correctly.
• Set the DRC to allow connections and
press the modem’s Pairing button
to connect them manually. (For the
procedures to set the DRC to allow
connections, refer to the DRC user manual.)
• Check if the DRC in your house is working
properly.
• Check that the DRC is turned on.
• Check if the modem’s MAC and PIN
numbers have been entered into the DRC
correctly.
• Set the DRC to allow connections and
press the modem’s Pairing button
to connect them manually. (For the
procedures to set the DRC to allow
connections, refer to the DRC user manual.)
SPECIFICATION
Feature Detailed description
Antenna type Chip antenna
Operation Voltage 5V DC ±10% or 3.3V DC±10%
Power Supply from Host
Interface Host I/F, Power
LED
Button
Dimension 80 x 55 x 20 mm
ZigBee
DRC Modem-A Modem-B
Specialized
modem
150mA @ 5V DC
150mA @ 3.3V DC
Power
• ON : Power is on
• OFF : Power is o
Demand
Response
Level
Level1 ~ Level4
Indicator
• ON : as paired
Pairing
• Blinking : hand shaking
• OFF : not paired
TX/RX pairing
Reset
• Compatible with IEEE802.15.4
standard to provide wireless
250Kbps data rate
• Operation at 2.4GHz frequency
band to meet worldwide
regulations
• Compliant with SEP1.0
DR-Ready_Modem_EN.indd 2 2011-05-27 �� 5:16:00
Loading...