Samsung DP17LS, DP15HS Schematic

COLOR MONITOR

DP15HS/HT DP17LS/LT

Manual

SERVICE

COLOR MONITOR CONTENTS

EXIT

1. Precautions

2. Product Specifications

3. Disassembly & Reassembly

4. Alignment & Adjustments

5. Troubleshooting

6. Exploded View & Parts List

7. Electrical Parts List

8. Block Diagram

9. Wiring Diagram

10. Schematic Diagrams

Samsung Electronics Co., Ltd. May 1999 Printed in Korea Code No.: BH68-00129A

This manual may not, in whole or in part, be copied, photocopied, reproduced, translated, or converted to any electronic or machine readable form without prior written permission of Samsung Electronics Co., Ltd.

DP15H*/DP17L* Service Manual First edition May 1999.

Printed in Korea.

Trademarks

Samsung is a registered trademark and DP15H*/DP17L* and MacMaster Cable Adapter are trademarks of Samsung Electronics Co., Ltd.

Macintosh, Centris, Quadra, Duo Dock, and Power Macintosh are trademarks of Apple Computer, Inc.

All other trademarks are the property of their respective owners.

ii DP15H*/DP17L*

WARNINGS

1. For continued safety, do not attempt to modify the circuit board.

2. Disconnect the AC power before servicing.

3. When the chassis is operating, semiconductor heatsinks are potential shock hazards.

1-1-1 Servicing the High Voltage VR

and CRT :

WARNING: A high voltage VR replaced in the wrong

direction may cause excessive X-ray emissions.

Caution:

When replacing the high voltage adjustment VR, it must be fixed by a soldering iron after it is properly set.

1. When servicing the high voltage system, remove the static charge by connecting a 10 kohm resistor in series with an insulated wire (such as a test probe) between the chassis and the anode lead.

2. If the HV VR requires adjustment, (a) Replace the VR and adjust the high voltage to the specification. (b) Use a soldering iron to melt the adjustment cap on the HV VR to prevent any movement.

3. When troubleshooting a monitor with excessively HV, avoid being unnecessarily close to the monitor. Do not operate the monitor for longer than is necessary to locate the cause of excessive voltage.

4. High voltage should always be kept at the rated value, no higher. Only when high voltage is excessive are X-rays capable of penetrating the shell of the CRT, including the lead in glass material. Operation at high voltages may also cause failure of the CRT or high voltage circuitry.

5. When the HV regulator is operating properly, there is no possibility of an X-ray problem. Make sure the HV does not exceed its specified value and that it is regulating correctly.

6. The CRT is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the CRT only with one that is the same or equivalent type as the original.

7. Handle the CRT only when wearing shatterproof goggles and after completely discharging the high voltage anode.

8. Do not lift the CRT by the neck.

1-1-2 Fire and Shock Hazard :

Before returning the monitor to the user, perform the following safety checks:

1. Inspect each lead dress to make certain that the leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the monitor.

2. Inspect all protective devices such as nonmetallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacitor networks, mechanical insulators, etc.

3. Leakage Current Hot Check (Figure 1-1):

WARNING: Do not use an isolation transformer during

this test.

Use a leakage current tester or a metering system that complies with American National Standards Institute (

ANSI C101.1, Leakage Current for

Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7).

4. With the unit completely reassembled, plug the AC line cord directly into a 120V AC outlet. With the unitÕs AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the power-plug prongs in the AC outlet and repeat the test.

Figure 1-1. Leakage Current Test Circuit

1-1-4 Product Safety Notices

Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection. The protection they give may not be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by

on schematics and parts lists. A substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire and / or other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate.

Components identified by on schematics and parts lists must be sealed by a soldering iron after replacement and adjustment.

DP15H*/DP17L* 1-1

1 Precautions

1-1 Safety Precautions

DEVICE UNDER TEST

TEST ALL

EXPOSED METAL

SURFACES

(READING SHOULD

NOT BE ABOVE 0.5mA)

LEAKAGE CURRENT

TESTER

2-WIRE CORD

ALSO TEST WITH

PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)

EARTH

GROUND

1. Servicing precautions are printed on the cabinet, and should be followed closely.

2. Always unplug the unitÕs AC power cord from the AC power source before attempting to: (a) remove or reinstall any component or assembly, (b) disconnect PCB plugs or connectors, (c) connect all test components in parallel with an electrolytic capacitor.

3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position.

4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the area around the serviced part has not been damaged.

1. Immediately before handling any semiconductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wriststrap device. To avoid a shock hazard, be sure to remove the wrist strap before applying power to the monitor.

2. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of an electrostatic charge.

3. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESDs.

4. Use only a grounded-tip soldering iron to solder or desolder ESDs.

5. Use only an anti-static solder removal device. Some solder removal devices not classified as Òanti-staticÓ can generate electrical charges sufficient to damage ESDs.

5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks).

6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500 V) to the blades of the AC plug.

The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm.

7. Never defeat any of the +B voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed.

8. Always connect a test instrumentÕs ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrumentÕs ground lead last.

6. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials.

7. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed.

Caution: Be sure no power is applied to the

chassis or circuit and observe all other safety precautions.

8. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting your foot from a carpeted floor can generate enough static electricity to damage an ESD.

9. Indicates ESDs on the Schematic Diagram in this manual.

1 Precautions

1-2 DP15H*/DP17L*

1-3 Electrostatically Sensitive Devices (ESD) Precautions

Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some fieldeffect transistors. The following techniques will reduce the incidence of component damage caused by static electricity.

1-2 Servicing Precautions

WARNING1: First read the “Safety Precautions” section of this manual. If unforeseen circumstances

create conflict between the servicing precautions and safety precautions, always follow the safety precautions.

WARNING2: A high voltage VR replaced in the wrong direction may cause excessive X-ray

emissions.

WARNING3: An electrolytic capacitor installed with the wrong polarity might explode.

DP15H*/DP17L* 2-1

2 Product Specifications

2-1 Specifications

Picture Tube: 15-Inch (38 cm): 13.8-inch (35 cm) viewable, 17-Inch (43 cm): 16-inch (40.6 cm) viewable,

Full-square flat-face tube, 90˚ Deflection, Semi- tint, Non-glare, Invar shadow mask, Anti-static silica coating, 0.28 mm Dot pitch

Scanning Frequency Horizontal : 30 kHz to 70 kHz (Automatic)

Vertical : 50 Hz to 160 Hz (Automatic) Display Colors Unlimited colors Maximum Resolution Horizontal : 1280 Dots Vertical : 1024 Lines Input Video Signal Analog, 0.7 Vp-p positive at 75 Ω, internally terminated Input Sync Signal Separate Sync: TTL level positive/negative Maximum Pixel Clock rate 110 MHz

Active Display 15” ; Horizontal : 267 mm ± 4 mm, Vertical : 200.5 mm ± 4 mm

17” ; Horizontal : 306 mm ± 4 mm (4:3 ratio), Vertical : 230.5 mm ± 4 mm Input Voltage AC 90 to 264 Volts, 60 Hz or 50 Hz ± 3 Hz Power Consumption 80 Watt (max) : 15”, 90 Watt (max) : 17” Dimensions Unit ; 15” : 14.25 x 15.11 x 15.11 Inches (362 x 384 x 384 mm)

(W x D x H) 17” : 16.22 x 16.54 x 16.36 Inches (412 x 420 x 415.5 mm)

Carton ; 15” : 17.87 x 19.57 x 17.52 Inches (454 x 497 x 445 mm)

17” : 21.02 x 21.73 x 18.39 Inches (534 x 552 x 467 mm)

Weight 15” : 26.5 lbs (12.0 kg) / 31.5 lbs (14.3 kg) (Net/Gross) 17” : 33.1 lbs (15.0 kg) / 38.6 lbs (17.5 kg)

Environmental Considerations Operating Temperature : 32°F to 104°F (0°C to 40°C)

Humidity : 10 % to 80 %

Storage Temperature : -4°F to 113°F (-20°C to 45°C)

Humidity : 5 % to 95 %

• Above models comply with SWEDAC (MPR II) recommendations for reduced electromagnetic fields.

• Designs and specifications are subject to change without prior notice.

Item Description

2 Product Specifications

2-2 DP15H*/DP17L*

2-2 Pin Assignments

Figure 2-1. Male Type Figure 2-2. Male Type

Sync Type

Pin No.

Macintosh

Separate

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15

Red Green Blue N-C DDC Return GND-R GND-G GND-B N-C GND-Sync/Self-raster N-C DDC Data H-Sync V-Sync DDC Clock

GND-R Red H/V Sync Sense 0 Green GND-G Sense 1 Reserved Blue Sense 2 GND V-Sync GND-B GND H-Sync

2 Product Specifications

DP15H*/DP17L* 2-3

QRS

Video

Sync

Horizontal

Vertical

CDE

Video

Sync

Separate Sync

2-3 Timing Chart

This section of the service manual describes the timing that the computer industry recognizes as standard for computer-generated video signals.

C D

Video

Sync

Video

Q R S

A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width C : Back porch D : Active time Q : Back porch R : Active time E : Front porch S : Front porch

fH (kHz) A µsec B µsec C µsec D µsec E µsec fV (Hz) O msec P msec Q msec R msec S msec Clock

Frequency (MHz)

Polarity H.Sync

V.Sync Remark

IBM VESA

800/85 Hz 800 x 600

1024/75 Hz 1024 x 768

1024/85 Hz 1024 x 768

VGA3/60 Hz

640 x 480

VGA2/70 Hz

720 x 400

31.469

31.777

3.813

1.907

25.422

0.636

70.087

14.268

0.064

1.080

12.711

0.413

28.322

Negative

Positive

Separate

31.469

31.778

3.813

1.907

25.422

0.636

59.940

16.683

0.064

1.048

15.253

0.318

25.175

Negative Negative Separate

37.500

26.667

2.032

3.810

20.317

0.508

75.000

13.333

0.080

0.427

12.800

0.027

31.500

Negative Negative Separate

43.269

23.111

1.556

2.222

17.778

1.556

85.008

11.764

0.671

0.578

11.093

0.023

49.500

Negative Negative Separate

46.875

21.333

1.616

3.232

16.162

0.323

75.000

13.333

0.064

0.448

12.800

0.021

36.000

Positive Positive

Separate

53.674

18.631

1.138

2.702

14.222

0.569

85.061

11.756

0.056

0.503

11.179

0.019

56.250

Positive Positive

Separate

60.023

16.660

1.219

2.235

13.003

0.203

75.029

13.328

0.050

0.466

12.795

0.017

78.750

Positive Positive

Separate

68.677

14.561

1.016

2.201

10.836

0.508

84.997

11.765

0.044

0.524

11.183

0.015

94.500

Positive Positive

Separate

800/75 Hz 800 x 600

640/75 Hz 640 x 480

640/85 Hz 640 x 480

Table 2-1. Timing Chart

Mode

Timing

2 Product Specifications

2-4 DP15H*/DP17L*

Memo

4-1-1 Before Making Adjustments

4-1-1 (a) ORIENTATION

When servicing, always face the monitor to the east.

4-1-1 (b) MAGNETIC FIELDS

Whenever possible, use magnetic field isolation equipment such as a Helmholtz field to surround the monitor. If a Helmholtz field is not available, frequently degauss the unit under test.

Caution: Other electrical equipment may cause

external magnetic fields which may interfere with monitor performance.

Use an external degaussing coil to limit magnetic build up on the monitor. If an external degaussing coil is not available, use the internal degaussing circuit. However, do not use the internal degaussing circuit more than once per 30 minutes.

4-1-1 (c) WARM-UP TIME

The monitor must be on for 30 minutes before starting alignment. Warm-up time is especially critical in color temperature and white balance adjustments.

4-1-1 (d) SIGNAL

Analog, 0.7 Vp-p positive at 75 ohm, internal termination Sync: Separate (TTL level negative/positive)

4-1-1 (e) SCANNING FREQUENCY

Horizontal: 30 kHz to 70 kHz (Automatic) Vertical: 50 Hz to 160 Hz (Automatic)

Unless otherwise specified, adjust at the 17Ó: 1024 x 768 mode (68 kHz/85 Hz), 15Ó: 800 x 600 mode (54 kHz/85 Hz) signals.

Refer to Table 2-1 on page 2-3.

.4-1-2 Required Equipment

The following equipment may be necessary for adjustment procedures:

4-1-2 (a) DISPLAY CONTROL ADJUSTMENT

1. Non-metallic (Ð) screwdriver:

1.5, 2.5, 3 mm

2. Non-metallic (+) screwdriver:

1.5, 2.5, 3 mm

3. Digital Multimeter (DMM), or Digital Voltmeter

4. Signal generator, or DM200 software

5. Software: Softjig or DM200

6. Interface Board Ver. 2.0 Code No. BH81-90001K

7. Parallel communications cable (25-pin to 25-pin); Code No. BH81-90001H

8. Signal cable (15-pin to 15-pin cable with additional 3-pin connector); Code No. BH81-90001J

9. 5 V DC adapter, not supplied

10. Personal computer

Note: Softjig AssÕy (includes items 6, 7 and 9)

Code No. BH81-90001L

4-1-2 (b) COLOR ADJUSTMENTS

1. All equipment listed in 4-1-2 (a), above

2. Color analyzer, or any luminance measurement equipment

DP15H*/DP17L* 4-1

4 Alignment and Adjustments

This section of the service manual explains how to make permanent adjustments to the monitor. Directions are given for adjustments using the monitor Interface Board Ver. 2.0 and software (Softjig).

4-1 Adjustment Conditions

Caution: Changes made without the Softjig are saved only to the user mode settings. As such, the

settings are not permanently stored and may be inadvertently deleted by the user.

4-1-3 Connecting the SoftJig

Connect the monitor to the signal generator and/ or PC as illustrated in Figures 4-1 and 4-2.

Note: The signal cable connector which includes

the 3-wire cable must connect to the monitor. If you use Setup 2 (PC only, no signal generator) you can only make adjustments to the signal timing available on that computer system. To make corrections to all factory timings requires the use of an additional signal generator.

4 Alignment and Adjustments

4-2 DP15H*/DP17L*

MONITOR

INTERFACE BOARD VER. 2.0

SIGNAL GENERATOR

3-WIRE CABLE

SIGNAL CABLE

5V DC ADAPTOR

PARALLEL CABLE

Figure 4-1. Setup 1, With Signal Generator

MONITOR

INTERFACE BOARD VER. 2.0

3-WIRE CABLE

SIGNAL CABLE

PARALLEL CABLE

D-SUB CONNECTOR

5V DC ADAPTOR

Figure 4-2. Setup 2, Without Signal Generator

4-2-1 HIGH VOLTAGE ADJUSTMENT

Signal: 1024 x 768 (68 kHz/85 Hz) (17Ó)

800 x 600 (54 kHz/85 Hz) (15Ó) Display image: DonÕt care Contrast: Minimum Brightness: Minimum Limit: 26.5 kV ± 0.2 kV (17Ó)

25 kV ± 0.2 kV (15Ó) exception) 26.0 kV ± 0.2 kV for 17Ó SDD CRT that

the DY type is DMX-1791AT

Measure the hight voltage level at the anode cap. High voltage should be within the limit as above. If the high voltage needs adjustment use the following procedure.

PROCEDURE

1. Turn the power off and disconnect the AC line

cord from the power source.

2. Turn the power on after connecting high

voltage Probe.

3. Using the jig, adjust the high voltage to the

specification.

* High Voltage Adjustment PROCEDURE using Softjig

① Select matching model name in ÒModelÓ field. ➁ Select Ò @7: Zero BeamÓ in menu after

selecting ÒExtra 1Ó

➂ Adjust high voltage using control bar after

selecting ÒHV MINÓ

➃ Turn the power off/on after adjustment

finished.

➄ Check the high voltage has been fixed with

adjusted value after reselecting Ò@7: Zero BeamÓ.

4-2-2 SCREEN VOLTAGE ADJUSTMENT

CONDITIONS

Signal: 1024 x 768 (68 kHz/85 Hz) (17Ó)

800 x 600 (54 kHz/85 Hz) (15Ó) Display image: DonÕt care Contrast: Minimum Brightness: Minimum Limit: 26.5 kV ± 0.2 kV (17Ó)

25 kV ± 0.2 kV (15Ó) Screen Voltage adjustment procedure using softjig

is all the same as 4-2-1 but selecting ÒG2 CONTÓ on the contrary to ÒHV MINÓ.

Table 4-1

4-2-3 CENTER RASTER

Adjust SW401 so that the back raster comes to the center when you apply each basic mode for 15Ó and 17Ó.

4-2-4 Centering

Centering means to position the center point of the display in the middle of the display area. Horizontal size and position and vertical size and position control the centering of the display.

Adjust the horizontal size and vertical size to their optimal settings: 306 mm (H) x 230 mm (V) for 17Ó, 267 mm (H) x 200 mm (V) for 15Ó.

Adjust the horizontal position and vertical position to ² 4.0 mm of the center point of the screen.

|A-B| ² 4.0 mm. |C-D| ² 4.0 mm.

Figure 4-3. Centering

* In Softjig window, ÒGeometryÓ has to be

selected for GD adjustment.

4-2-4 (a) HORIZONTAL SIZE ADJUSTMENT CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó) Display image: Crosshatch pattern Brightness: Maximum Contrast: Maximum

4 Alignment and Adjustments

DP15H*/DP17L* 4-3

4-2 Display Control Adjustments

DISPLAY AREA

EDGE OF BEZEL

17”

15”

CRT type Screen Voltage

M41QAR361X11*(*) M41QAQ261X11*(*) M41LFQ903X28(L), etc

M41EHN325X160/3F**U M41EHN323X160/3F**U M41LLJ507XX43*(F5), (F5W3) M41LLH507XX43*(F5)

M36QAM351X11*(*) M36LGE128X2**(*)

M36KUK35X02(*/LP), etc

480V

10V

500V

10V

630V

10V

560V

10V

600V

10V

520V

10V

Use control bar after selecting ÒH-SIZEÓ in left menu to adjust the horizontal size of the display pattern to 306 mm (17Ó) and 267 mm (15Ó). (Tolerance: ± 3 mm.)

If ÒH-SIZEÓ is not enough to adjust it, select ÒSIZE B+Ó by turns.

4-2-4 (b) VERTICAL SIZE ADJUSTMENT CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó) Display image: Crosshatch pattern Brightness: Maximum Contrast: Maximum

Use control bar after selecting ÒV-SIZEÓ in left menu to adjust the vertical size of the display pattern to 230 mm (17Ó) and 200 mm (15Ó). (Tolerance: ± 3 mm.)

4-2-4 (c) HORIZONTAL POSITION ADJUSTMENT CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)

Display image: Crosshatch pattern

Use control bar after selecting ÒH-POSITIONÓ in left menu to center the horizontal image on the raster.

4-2-4 (d) VERTICAL POSITION ADJUSTMENT CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)

Display image: Crosshatch pattern

Use control bar after selecting ÒV-POSITIONÓ in left menu to center the vertical image on the raster.

4-2-5 Linearity

Linearity affects the symmetry of images as they appear on the screen. Unless each row or column of blocks in a crosshatch pattern is of equal size, or within the tolerances shown in Tables 4-2 and 4-3, an image appears distorted, elongated or squashed.

Table 4-2. Standard Modes Linearity: 640x480/75Hz,

800x600/85Hz and 1024x768/85Hz

Table 4-3. Other Modes Linearity: VGA, SVGA, XGA,

MAC, etc.

4-2-5 (a) HORIZONTAL LINEARITY ADJUSTMENT CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó) Display image: Crosshatch pattern Brightness: Maximum Contrast: Maximum

To adjust the Horizontal Linearity, refer to Tables 4-2 and 4-3 for the tolerance range.

Increase or decrease H_LIN to optimize the image.

4-2-5 (b) VERTICAL LINEARITY ADJUSTMENT CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó) Display image: Crosshatch pattern Brightness: Maximum Contrast: Maximum

To adjust the Vertical Linearity, refer to Tables 4-2 and 4-3 for the tolerance range.

Use control bar after selecting ÒV-LINEARITY BALÓ in left menu to optimize the image.

4 Alignment and Adjustments

4-4 DP15H*/DP17L*

Figure 4-5. Pinbalance

4 : 3

5 : 4

Horizontal: 17.8~20.5 Vertical : 17.8~20.5

Horizontal: 16.7~19.2 Vertical : 17.8~20.5

Supported Timing Mode

Each block (10 %)

Difference between

adjacent blocks (5 %)

Horizontal: Less than 0.96 mm Vertical : Less than 0.96 mm

Horizontal: Less than 0.90 mm Vertical : Less than 0.96 mm

4 : 3

5 : 4

Horizontal: 18.2~20.1 Vertical : 18.2~20.1

Horizontal: 17.1~18.9 Vertical : 18.2~20.1

Standard Modes Linearity

Each block (10 %)

Difference between

adjacent blocks (4 %)

Horizontal: Less than 0.77 mm Vertical : Less than 0.77 mm

Horizontal: Less than 0.72 mm Vertical : Less than 0.77 mm

4-2-6 Trapezoid Adjustment

CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó) Display image: Crosshatch pattern Brightness: Maximum Contrast: Maximum

Use control bar after selecting ÒTRAPEZOIDÓ in left menu to make the image area rectangular.

Figure 4-4. Trapezoid

4-2-7 Pinbalance Adjustment

CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó) Display image: Crosshatch pattern Brightness: Maximum Contrast: Maximum

Figure 4-5. Pinbalance

Use control bar after selecting ÒPINBALANCEÓ in left menu to optimize the image.

4-2-8 Parallelogram Adjustment

CONDITIONS

Scanning Frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó) Display image: Crosshatch pattern Brightness: Maximum Contrast: Maximum

Use control bar after selecting ÒPARALLELÓ in left menu to make the image area rectangular.

Figure 4-6. Parallelogram

4-2-9 Side Pincushion Adjustment

CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)

Display image: Crosshatch pattern

Use control bar after selecting ÒPINCUSHIONÓ in left menu to straighten the sides of the image area.

4-2-10 Tilt Adjustment

CONDITIONS

Scanning Frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó) Display image: Crosshatch pattern Brightness: Maximum Contrast: Maximum

Use control bar after selecting ÒROTATIONÓ in left menu to correct the tilt of the display.

4-2-11 Degauss

No adjustments are available for the degaussing circuit. The degaussing circuit can effectively function only once per 30 minutes.

4-2-12 To Delete the User Mode Data

To delete the adjustment data from the user modes, click Ò@4: USER DELETEÓ in right ment.

4-2-13 Save the Data

To save the adjustment data for a mode, press Ò@3: ALL MODE SAVEÓ in right ment.

4 Alignment and Adjustments

DP15H*/DP17L* 4-5

| A - B | < 4 mm

4 mm

D1 D2 D1

| C1 |, | C2 | ≤ 2.0 mm, | D1 |, | D2 | ≤ 2.0 mm.

Figure 4-7. Pincushion

D1 D2

CAUTION:Check below condition before color

adjustment Video signal : Analog 0.7 Vp-p (at 75 Ω) Sync : TTL level (H, V seperate signal)

* Select ÒColorÓ in Softjig menu for color adjustment.

4-3-1 Color Coordinates (Temperature)

Color temperature is a measurement of the radiant energy transmitted by a color. For computer monitors, the color temperature refers to the radiant energy transmitted by white. Color coordinates are the X and Y coordinates on the chromaticity diagram of wavelengths for the visible spectrum.

CONDITIONS

Measurement instrument: Color analyzer Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)

Display image: White flat field at

center of display area

Luminance: Maximum

PROCEDURE

Use the directions in sections 4-3-2 through 4-3-3 to adjust the color coordinates for: 9300K to x = 0.283 ± 0.02, y = 0.298 ± 0.02 6500K to x = 0.313 ± 0.02, y = 0.329 ± 0.02

4-3-2 Color Adjustments for 9300K

4-3-2 (a) BACK RASTER COLOR ADJUSTMENT CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó) Display image: Back raster pattern Brightness: Maximum Contrast: Maximum

1. Select Ò@1: CHANNEL 1Ó in right menu to

control the color for 9300K.

2. Adjust the luminance of the back raster to

between 0.5 to 0.7 ft-L using contron bar after selecting ÒGREEN CUTOFFÓ in the menu.

3. Use control bar after selecting ÒBLUE

CUTOFFÓ in left menu to set the ÒyÓ coordinate to 0.298 ± 0.02.

4. Use control bar after selecting ÒRED

CUTOFFÓ in left menu to 0.283 ± 0.02.

* If color values would not be matched desirable

values, repeat sequence 3 and 4 after readjusting ÒGREEN CUTOFFÓ control a little different.

4-3-2 (b) WHITE BALANCE ADJUSTMENT CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó) Display image: White box pattern Brightness: 0.06ft-L at Back Raster

Pattern Display Contrast: Maximum

Figure 4-8. White Box Pattern

1. Use control bar after selecting ÒRED GAINÓ,

ÒGREEN GAINÓ and ÒBLUE GAINÓ to adjust the luminance to 45 ft-L (15Ó) and 46 ft-L (17Ó) with the color coordinates ranged for 9300K to x = 0.283 ± 0.02, y = 0.298 ± 0.02.

exception) 17Ó SDD CRT type-named (*/S-2) : 42ft-L.

4-3-2 (c) ABL ADJUSTMENT CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó) Display image: Full white pattern Brightness: Maximum Contrast: Maximum

Figure 4-9. Full White Pattern

1. Check the ABL. If it is not within the

specifications, use the ABL controls to adjust it. (15Ó: 33 ± 1 ft-L, 17Ó: 36 ± 1 ft-L )

2. Select Ò@4: COLOR SAVEÓ to save the data.

3. Select Ò@6: ALL COLOR SAVEÓ to save the

CH2.

4 Alignment and Adjustments

4-6 DP15H*/DP17L*

4-3 Color Adjustments

1/3H-1/2H

1/3V-1/2V

FRONT BEZEL OPENING BACK RASTER

WHITE WINDOW

FRONT BEZEL OPENING BACK RASTER

WHITE WINDOW

4-3-2 (d) WHITE BALANCE ADJUSTMENT VERIFICATION CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)

Display image: Back raster pattern

Full White Pattern

X-Y Coordinates: x = 0.283 ± 0.02,

y = 0.298 ± 0.02 ABL Luminance Refer to 4-3-2(c) Brightness: Maximum Contrast: 5 ft-L, 24 ft-L

1. Check whether the color coordinates of the

back raster satisfy the above spec. If they do not, return to 4-3-2 (a) and readjust

all settings.

2. Display a full white pattern.

3. Select ÒGeometryÓ in softjig menu.

4. Select Ò@7: 5-ft Ò in right menu.

5. Check whether the white coordinates of the

video meet the above coordinates spec.

6. Select Ò@8: 24-ft Ò in right menu.

7. Check whether the white coordinates of the

video satisfies the above spec. If they do not, return to 4-3-2 (a) and readjust

all settings.

Select ÒColorÓ and click Ò@2: CHANNEL 2Ó for color ajdustment for 6500K Repeat the sequence of 9300K adjustment. The luminance values the same as 9300K, but the color coordinated of back raster and white box are : x = 0.313

± 0.02 y = 0.329 ± 0.02

4-3-3 Luminance Uniformity Check

Luminance is considered uniform only if the ratio of lowest to highest brightness areas on the screen is not less than 7.5:10.

CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)

(1024 x 768) Display image: White flat field Brightness: Cut off point at 24 ft-L Contrast: Maximum

PROCEDURE

Measure luminance at nine points on the display screen (see figure below).

4-3-4 Focus Adjustment

CONDITIONS

Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó)

(1024 x 768) Display image: ÒHÓ character pattern Brightness: Cut off point Contrast: Maximum

PROCEDURE

1. Adjust the Focus VR on the FBT to display the

sharpest image possible.

2. Use Locktite to seal the Focus VR in position.

4-3-5 Color Purity Adjustment

Color purity is the absence of undesired color. Conspicuous mislanding (unexpected color in a uniform field) within the display area shall not be visible at a distance of 50 cm from the CRT surface.

CONDITIONS

Orientation: Monitor facing east Scanning frequency: 68 kHz/85 Hz (17Ó)

54 kHz/85 Hz (15Ó) Display image: White flat field Luminance: Cut off point at the center

of the display area

Note: Color purity adjustments should only be

attempted by qualified personnel.

4 Alignment and Adjustments

DP15H*/DP17L* 4-7

Figure 4-10. Luminance Uniformity Check Locations

PROCEDURE

For trained and experienced service technicians only.

Use the following procedure to correct minor color purity problems:

1. Make sure the display is not affected by external magnetic fields.

2. Very carefully break the glue seal between the 2-pole purity convergence magnets (PCM), the band and the spacer (see Figures 4-12).

3. Make sure the spacing between the PCM assembly and the CRT stem is 29 mm ± 1 mm.

4. Display a green pattern over the entire display area.

5. Adjust the purity magnet rings on the PCM assembly to display a pure green pattern. (Optimum setting: x = 0.295 ± 0.015, y = 0.594 ± 0.015)

6. Repeat steps 4 and 5 using a red pattern and then again, using a blue pattern.

Table 4-4. Color Purity Tolerances

(For 9300K color adjustment: x = 0.283 ± 0.02, y = 0.298 ± 0.02)

7. When you have the PCMs properly adjusted, carefully glue them together to prevent their movement during shipping.

4 Alignment and Adjustments

4-8 DP15H*/DP17L*

Red: x = 0.640 ± 0.015 y = 0.323 ± 0.015 Green: x = 0.295 ± 0.015 y = 0.594 ± 0.015 Blue: x = 0.142 ± 0.015 y = 0.066 ±0.015

DP15H*/DP17L* 5-1

5 Troubleshooting

5-1 Parts Level Troubleshooting

Notes: 1. If a picture does not appear, fully rotate the brightness and contrast controls clockwise and reinspect.

2. Check the following circuits.

• No raster appears: Power circuit, Horizontal output circuit.

• High voltage develops but no raster appears: Video output circuits.

• High voltage does not develop: Horizontal output circuits.

5-1-1 No Power Supply

Chirping noise exists?

Check and replace IC601.

Check and replace D601, FH1

Done.

Yes

Repeating start?

Check and replace D606.

Yes

IC601 Pin 1 waveform is right?

Check and replace D614, IC601,

Q602, ZD601.

Yes

C622 Voltage is 13 V ± 0.5V?

Check and replace IC201, IC301,

IC401, Q402, Q404.

Yes

Normal operation

Replace Main board.

Yes

Verify voltages.

Yes

WAVEFORMS

100 V (IC601, #1)

CH1 P-P = 100 V CH1 RMS = 350.2 V

5 Troubleshooting

5-2 DP15H*/DP17L*

5-1-2 DPMS Failure

Make No H/V sync (power off

mode)

Check signal source

H/V sync video level.

LED blinks

Check IC201 Pin 40.

Yes

+12 V line off

Check IC201 Pin 5.

Yes

IC602 Pin 4

voltage exists?

Check IC201 Pin 6.

Check and replace IC602.

Yes

IC601 Pin 1 output

voltage exists?

Refer to 5-1-1 No Power Supply.

Done

Yes

WAVEFORMS

100V (IC601, #1)

CH1 P-P = 100V CH1 RMS = 325.8 V

5 Troubleshooting

DP15H*/DP17L* 5-3

5-1-3 H_Deflection Failure

Does Horizontal paluse signal

appear at at Pin 8 of IC401?

Check IC401.

Yes

Does 110 Vp-p signal appear

at Collector of Q403?

Check Q443.

Check Q402, Q404, T401.

WAVEFORMS

2.00 V (IC401, #6)

CH1 P-P = 2.00V CH1 RMS = 5.868V

1.00V (IC401, #8)

CH1 P-P = 1.00V CH1 RMS = 1.298V

20.0 V (Q403, Collector)

CH1 P-P = 20.0 V CH1 RMS = 46.80V

Does PWM output signal appear

at Pin 6 (H_out) of IC401?

Check IC401.

Check 12 V line.

Yes

Does DC 12V appear at

Pin 10 of IC401?

Yes

7-1-4 S Correction Failure

S1~S3 signals are right at each

frequency block?

Check S1 ~ S3 signal.

Check and replace Q404, Q409, Q410,

Q414, Q415, Q416

Yes

Check and replace IC201.

+ 45 hidden pages