Samsung DCS-408, DCS-408i User Manual 2

SAMSUNG

DCS

COMBINED

PROGRAMMING MANUAL

DCS DCS COMPACT

for

DCS COMPACT II DCS-816 DCS-408 DCS-408i

Publication Information

Samsung Telecoms reserves the right without prior notice to revise information in this publication for any reason.

Samsung Telecoms also reserves the right without prior notice to make changes in design or components of equipment as engineering and manufacturing may warrant.

Disclaimer

Samsung Telecoms is not responsible for errors or problems arising from customers not installing, programming or operating their Samsung systems as described in this manual.

Samsung Telecoms (UK) Limited

All rights reserved. No part of this manual may be reproduced in any form or by any means – graphic, electronic or mechanical, including recording, taping, photocopy or information retrieval system – without express written permission of the publisher of this material.

Part No.:12623 Version 2.0

EU Declaration of Conformity

For other directives relevant to DCS Compact II, DCS-816, DCS-408 and DCS-408i systems, refer to the Samsung website at:

www.samsung-telecoms.co.uk

DCS CONTENTS COMBINED PROGRAMMING MANUAL NOVEMBER 2001

Part

1 Introduction to Programming .....................................1–1

1.1 Using this Manual...........................................................................1–1

1.2 Programming Overview ..................................................................1–2

1.3 Programming Levels......................................................................1–2

1.3.1 System Level ............................................................................ 1–2

1.3.2 Customer Level ......................................................................... 1–2

1.3.3 Station Level............................................................................. 1–3

1.4 Keys Used for Programming ..........................................................1–3

1.4.1 Soft Keys .................................................................................. 1–3

1.4.2 Other Keys ............................................................................... 1–3

1.5 Programming Procedures..............................................................1–4

1.5.1 Precautions When Programming ............................................... 1–4

1.5.2 Opening System or Customer Level Programming ..................... 1–4

1.5.3 Opening Station Level Programming.......................................... 1–5

1.5.4 Programmi ng DCS-408 and 408i Systems..................................1–5

2 Program (MMC) List and Default Data ......................2–1

2.1 Program (MMC) List.......................................................................2–1

2.2 Default Data....................................................................................2–3

2.3 System Configuration: Quick Reference...................................... 2–9

3 Special Applications ....................................................3–1

Voice Mail / Auto Attendant Integration...................................................3–2

Individual Station Page............................................................................3–4

CLIP (Calling Line Identification Presentation)........................................3–5

Toll Restriction (Call Barring) Overview ...................................................3–6

S0 Overview.............................................................................................3–8

4 MMCs (in numerical order) ........................................4–1

DCS INTRODUCTION COMBINED PROGRAMMING MANUAL NOVEMBER 2001

Part 1. Introduction to Programming

This manual describes the MMC pro gramming required for the following types of Samsung DCS keyphone system:

• DCS

• DCS Compact (Compact I)

• DCS Compact II

• DCS-816

• DCS-408

• DCS-408i.

In this manual, these systems are referred to as “DCS,” “Compact I (CI),” “Compact II

(CII)," "816," "408" and “408i” respectively. Programming requirements for these system types are generally the same, but occasionally there are differences. Users of 408 and 408i systems should also read Programming DCS-408 and 408i Systems in section 1.5.4 of this manual. Unless otherwise stated, references to “DCS” include Compact I sy stems.

The different system types are discussed fully in the separate Samsung General De- scription manuals for each system, where these have been published.

Software Version Numbers

The software version numbers of the systems for which this programming manual is relevant are: DCS and Compact II=V6.10 or later; 816=V1.09 or later; 408 and 408i=1.04 or later.

1.1 Using This Manual

• It is recommended that you read the whole of Part 1 of this manual which provides a

useful overview to MMC programming procedures.

• For a comprehensive list of available MMCs, see Part 2.

• For quick reference, Part 2 also provides a table listing the default settings for each

MMC and indicating which systems can use each MMC . A “Y” (“Yes”) in the appropriate column indicates that it can be used for that system.

• To quickly check allowed configuration settings for each type of system—number of

trunk group members, card port numbers, and so on—see section 2.3 System Con- figuration: Quick Reference in Part 2.

• To begin programming, refer to the appropriate MMC(s) in Part 4. Check the se-

lected MMC header bar to make sure the program is available on your system, if you haven’t already done so.

• Refer to Part 3, Special Applications, for further information on voice mail / auto at-

tendant integration, individual station paging, CLIP (Calling Line Identification Presentation), toll restriction (call barring) and S

0 programming.

1-1

DCS INTRODUCTION COMBINED PROGRAMMING MANUAL NOVEMBER 2001

1.2 Programming Overview

When the keyphone system arrives from the factory it contains default data. This needs to be customised, using the MMC programs, to suit the customer’s requirements.

MMC stands for Man Machine Code and each MMC is assigned a three-digit code (100, 101, and so on). These MMCs are used to view, create or change customer data on a display keyphone (called KMMC programming). For example, MMC 601 is used to cr eate a station group; sy stem speed dial numbers are entered in MMC 705; key functions are assigned to individual keyphones (or “keysets”) using MMC 722; and system dialling codes (such as extension numbers and feature codes) can be changed in MMC

724.

1.3 Programming Levels

There are three levels of programming: System level, Customer level and Station level. System and Customer levels allow system-wide programming and are under passcode protection to restrict access. System programming is done by the system installer (or system technician), usually on a one-off basis, but also to manage any changes in the customer’s requirements. Customer programming is done by the system administrator, on a day to day basis, to manage station users’ requirements. Station level programming does not require a passcode, allowing station users to make simple changes to their keyset features.

To prevent conflicting data from being entered, only one person at a time can enter System or Customer programming. If you attempt to enter programming mode while another keyset is being used for programming, your display shows [xxx PGM MODE] where “xxx” is the key set extension number of the station in programming mode. While

programming is in progress, normal system operation is not affected.

1.3.1 System Level

This level is entered via MMC 800 and requires the installer’s (technician’s) passcode. This is the highest level and allows access to all system programs, station programs and mainte nance programs. The installer (sometimes called the installing technician) also decides which programs are accessible to the customer (the system administrator) at Customer level.

• All MMCs are accessible at this level.

1.3.2 Customer Level

This level is entered via MMC 200 and requires the customer’s passcode. It allows access to station programs and system programs permitted by the system installer in MMC 802. When the system administrator uses the customer passcode to access station programs, data for all stations can be viewed or changed. Changes can be made either system-wide or to selected keysets. (The system administrator should also refer to the System Administration manual for their keyphone system if this is available.)

• Accessible MMCs at this level are designated by the installer.

1-2

DCS INTRODUCTION COMBINED PROGRAMMING MANUAL NOVEMBER 2001

1.3.3 Station Level

The system administrator or keyset user can access certain programs at a station without using a passcode. At this level, only data for the selected station can be changed. You should refer to the instructions provided in the Samsung DCS Keyset User Guide.

• Accessible MMCs at this level are nos. 100–121.

1.4 Keys Used for Programming

Programming may be done from any 6-button (6B), 12-button (12B) or 24-button (24B) keyset with a liquid crystal display (LCD). (Refer to the Samsung DCS Keyset User Guide for a full description of keyset operation.)

1.4.1 Soft Keys

The three keys directly below the LCD are called soft keys. The left-hand soft key is designated as the LEFT soft key. This key is used to save any changed data while programming, or to move the cu rsor to the left on the LCD.

The right-hand soft key is designated as the RIGHT soft key. This key is used to save any changed data while programming, or to move the cursor to the right on the LCD. DCS Euro Display Keysets

1.4.2 Other Keys

The following keys perform special functions:

VOLUME UP (+) / DOWN ( –) Scroll up/down through available options* KEYPAD Enter data using keys 0 –9 and [, and dial options* HOLD Clear previous entry ANS/RLS Select “ALL” option (e.g. to make data apply to all,

rather than selected, stations) SPEAKER Store data and advance to next MMC TRSF Enter programming mode or Store data and exit programming mode

* Note: Many MMCs allow you to dial codes using the keypad to select options quickly. Alternatively, you can press the VOLUME Up and Down keys (+ and – ) to scroll through and select options. Use whic hever method you prefer.

1-3

DCS INTRODUCTION

try

select the country and press the RIGHT soft key.

Use the VOLUME Up/Down keys to select YES and press the RIGHT soft key. When

scribed next. The

COMBINED PROGRAMMING MANUAL NOVEMBER 2001

The 6, 12 or 24 extra programmable keys can be set up to perform specific functions when pressed during normal operation. During programming, some of these keys also perform other specific functions. This is described in the individual MMC program procedure where applicable.

1.5 Programming Procedures

1.5.1 Precautions When Programming

• The keyset must be on-hook (handset down) to allow programming.

• Programming is available on any digital keyset with an LCD.

• Programming is available only on digital telephones (not analogue ones).

• If ‘INVALID DATA’ appears in the LCD while programming, you should re-enter the

correct data.

• When you have successfully completed an entry, the LCD automatically changes for the next step.

• Programming halts if you have not pressed a key for a certain period of time (30 se conds by default, but this can be changed).

• Programming halts if you pick up the handset while programming.

• If you pick up the handset while programming, or the telephone plug is pulled out,

any new data shown in the LCD are saved.

IMPORTANT

When installing and programming a ‘default’ system

for the first time:

The system requires that you select the correct software version for your coun (e.g. by selecting “UK”) before you can do any other programming via either a ke phone (KMMC programming) or a PC (PCMMC programming).

To select the country:

1. Press the TRSF key.

2. Enter 800 followed by the default passcode (4321)

The system sounds a warning and displays on the keyset:

Use the VOLUME Up/Down keys to The keyset displays:

ENABLE TECH. PROG SELECT COUNTRY

DEFAULTING SYSTM ARE YOU SURE?NO

defaulted to the correct version, you can open programming as de country version selected can be changed in MMC 812, Select Country.

1-4

DCS INTRODUCTION COMBINED PROGRAMMING MANUAL NOVEMBER 2001

1.5.2 Opening System or Customer Programming

To open programming:

1. Press the TRSF key.

2. Enter the MMC program number 200 (for Customer level programming) or 800 (for System level programming).

3. Enter the relevant passcode.

4. Press key 1 (or use the VOLUME Up or Down key) to select ‘ENABLE’.

5. Press the SPEAKER key to have the program selection mode appear (or press the TRSF key to halt programming).

6. Enter the MMC number, or select the program number with the Up or Down key and press the SPEAKER key.

When opening system programming, you are advised to check MMC 812 (Select Country) to ensure that the correct country has been selected before you do any other programming.

Carefully follow the instructions given with each MMC to program your system correctly.

1.5.3 Opening Station Level Programming

To open programming:

1. Press the TRSF key.

2. Enter the MMC program number.

Carefully follow the instructions given with each MMC to program your system correctly.

1.5.4 Programming DCS-408 and 408i Systems

Although physically similar in appearance, the “408” and “408i” are different systems and may have different programming requirements and features. For example, the 408i supports ISDN whereas the 408 does not. Thus, an MMC relevant to one system may not be relevant to the other. Similarly, where an MMC relates to both systems, some features available on the 408i system may not be available on the 408 system, and vice versa.

This will be indicated in the MMC description, where appropriate. These systems also differ significantly from all other keyphone systems, both in size and

physical appearance. In comparison with other systems, when programming your 408 or 408i:

• Extension, group and trunk numbers are two digits by default (e.g. extension 21, trunk 71, etc). All other systems use 3-digit numbers by default (e.g. extension 201, trunk 701, etc).* Examples of programming shown in this manual use 3-digit numbers for convenience only.

(*Unless changed by the system installer in MMC 724.)

• You can set up to four ‘Normal’ station groups. Group types AA, VM/AA and UCD are not permitted.

• Only two trunk groups, 8 and 9, are available. (All other systems support groups 9 and 80–82.)

1-5

DCS MMC LIST COMBINED PROGRAMMING MANUAL NOVEMBER 2001

Part 2. Program MMC List & Default Data

2.1 Program (MMC) List

100: STATION LOCK 317: ASSIGN STATION/STATION USE 101: CHANGE USER PASSCODE 318: DISTINCTIVE RING 102: CALL FORWARD 319: BRANCH GROUP 103: SET ANSWER MODE 400: CUSTOMER ON/OFF PER TRUNK 104: STATION NAME 401: CO/PBX LINE 105: STATION SPEED DIAL 402: TRUNK DIAL TYPE 106: STATION SPEED DIAL NAME 403: TRUNK TOLL CLASS 107: KEY EXTENDER 404: TRUNK NAME 108: STATION STATUS 405: TRUNK NUMBER 109: DATE DISPLAY 406: TRUNK RING ASSIGNMEN T 110: STATION ON/OFF 407: FORCED TRUNK RELEASE 111: KEYSET RING TONE 408: ASSIGN TRUNK MUSIC ON HOLD SOURCE 112: ALARM REMINDER 409: TRUNK STATUS READ 113: VIEW MEMO NUMBER 410: ASSIGN DISA TRUNK 114: STATION VOLUME 411: ASSIGN E1 SIGNAL TYPE 115: SET PROGRAMMED MESSAGE 412: ASSIGN TRUNK SIGNAL 116: ALARM AND MESSAGE 414: MPD/PRS SIGNAL 119: SET CLIP DISPLAY 415: REPORT TRUNK ABANDON DATA 121: KEYSET LANGUAGE 416: ASSIGN AC15 TRANSLATION 200: OPEN CUSTOMER PROGRAMMING 417: PRI CRC4 OPTION 201: CHANGE CUSTOMER PASSCODE 418: CARD RESTART 202: CHANGE FEATURE PASSCODES 419: BRI OPTION 203: ASSIGN UA DEVICE 420: PRI OPTION 204: COMMON BELL CONTROL 421: MSN DIGIT 205: ASSIGN LOUD BELL 422: ASSIGN TRUNK COS 206: BARGE-IN TYPE 423: S/T MODE 207: ASSIGN VM/AA PORT 424: S0 MAPPING 208: ASSIGN RING TYPE 426: TRUNK GAIN CONTROL 209: ASSIGN ADD-ON MODULE 427: R2MFC SIGNAL 210: CUSTOMER ON/OFF 428: ASSIGN TRUNK/TRUNK USE 211: DOOR RING ASSIGNMENT 500: SYSTEM-WIDE COUNTERS 212: ALARM RINGING STATION 501: SYSTEM-WIDE TIMERS 213: ALARM MESSAGE 502: STATION-WIDE TIMERS 214: DISA ALARM RINGING STATION 503: TRUNK-WIDE TIMERS 215: VOICE DIALLER OPTION S 504: PULSE MAKE/BREAK RATIO 216: VOICE DIALLER ASSIGNMENTS 505: ASSIGN DATE AND TIME 217: CCC OPTION 506: TONE CADENCE 219: COMMON RELAY SERVICE TYPE 507: ASSIGN AUTO NIGHT TIME 220: ISDN SERVICE TYPE 508: CALL COST 300: CUSTOMER ON/OFF PER STATION 509: C.O. TONE CADENCE 301: ASSIGN STATION COS 510: SLI RING CADENCE 302: PICKUP GROUPS 511: MW LAMP CAD 303: ASSIGN BOSS/SECRETARY 512: ASSIGN HOLIDAY 304: ASSIGN STA TION/TRUNK USE 600: ASSIGN OPERATOR GROUP 305: ASSIGN FORCED CODE 601: ASSIGN STATION GROUP 306: HOT LINE 602: STATION GROUP NAME 308: ASSIGN BACKGROUND MUSIC SOURCE 603: ASSIGN TRUNK GROUP 309: ASSIGN STATION MUSIC ON HOLD 604: ASSIGN STATION TO PAGE ZONE 310: LCR CLASS OF SERVICE 605: ASSIGN EXTERNAL PAGE ZONE 311: ASSIGN SIM PARAMETER 606: ASSIGN SPEED BLOCK 312: ALLOW CLIP 607: UCD OPTIONS 313: ASSIGN PIN CODE 608: ASSIGN CLIP REVIEW BLOCK 314: CONFIRM OUTGOING CAL L 700: COPY COS CONTENTS 315: SET RELOCATION 701: ASSIGN COS CONTENTS 316: COPY STATION USABLE 702: TOLL DENY TABLE

2-1

DCS MMC LIST COMBINED PROGRAMMING MANUAL NOVEMBER 2001

703: TOLL ALLOWANCE TABLE 736: ASSIGN AA MOH 704: ASSIGN WILD CHARACTER 737: DECT SYSTEM CODE 705: ASSIGN SYSTEM SPEED DIAL 738: DECT CLEAR REGISTRATION 706: SYSTEM SPEED DIAL BY NAME 739: BSI DOWNLOAD 707: AUTHORISATION CODE 740: STATION PAIR 708: ACCOUNT CODE 741: BSI CARD RESTART 709: PBX ACCESS CODE 742: BSI STATUS 710: LCR DIGIT TABLE 743: DECT BASE STATION (DBS) STATUS 711: LCR TIME TABLE 744: DECT REGISTRATION ON/OFF 712: LCR ROUTE TABLE 745: BSI CARRIER 713: LCR MODIFY DIGIT TABLE 750: VM CARD RESTART 714: DDI NUMBER & NAME TRANSLATION 751: ASSIGN MAILBOX 715: PROGRAMMED STATION MESSAGE 752: AUTO RECORD 716: UK LCR OPTION 753: WARNING DESTINATION 717: PIN CODE 754: VM HALT 718: MY AREA CODE 755: VM ALARM 720: COPY KEY PROGRAMMING 756: ASSIGN VM MOH 721: SAVE STATION KEY PROGRAMMING 757: VM IN/OUT 722: STATION KEY PROGRAMMING 800: ENABLE TECHNICIAN PROGRAM 723: SYSTEM KEY PROGRAMMING 801: CHANGE TECHNICIAN PA SSCODE 724: DIAL NUMBERING PLAN 802: CUSTOMER ACCESS MMC NUMBER 725: SMDR OPTIONS 803: ASSIGN TENANT GROUP 726: VM/AA OPTIONS 804: SYSTEM I/O PARAMETER 727: SYSTEM VERSION DISPL AY 805: TX LEVEL & GAIN 728: CLIP TRANSLATION TA BLE 806: CARD PRE-INSTALL 730: AA RECORD GAIN 807: VOLUME CONTROL 731: AA RAM CLEAR 808: T1 TRUNK CODING 732: AA TRANSLATION TABLE 809: SYSTEM MMC LANGUAGE 733: AA PLAN TABLE 810: HALT PROCESSING 734: AA MESSAGE MATCH 811: RESET SYSTEM 735: AA USE T ABLE 812: SELECT COUNTRY

2-2

DCS DEFAULT DATA COMBINED PROGRAMMING MANUAL NOVEMBER 2001

2.2 Default Data

Station Programs

DCS CI CII 816 408 408i 100: STATION LOCK Y Y Y Y Y Y ALL STATIONS UNLOCKED 101: CHANGE USER PASSCODE Y Y Y Y Y Y ALL STATION PASCODES=1234 102: CALL FORWARD Y Y Y Y Y Y ALL STATION=0 (FWD CANCEL)

103: SET ANSWER MODE Y Y Y Y Y Y

104: STATION NAME Y Y Y Y Y Y NONE 105: STATION SPEED DIAL Y Y Y Y Y Y NONE 106: STATION SPEED DIAL NAME Y Y Y Y Y Y NONE 107: KEY EXTENDER Y Y Y Y Y Y NONE 108: STATION STATUS Y Y Y Y Y Y SEE MMC 108 109: DATE DISPLAY Y Y Y Y Y Y COUNTRY: WESTERN

110: STATION ON/OFF Y Y Y Y Y Y AUTO HOLD: OFF

111: KEYSET RING TONE Y Y Y Y Y Y SELECTION=5 112: ALARM REMINDER Y Y Y Y Y Y ALARMS SET TO NOTSET 113: VIEW MEMO NUMBER Y Y Y Y Y Y NO MEMOS ENTERED 114: STATION VOLUME Y Y Y Y Y Y RING VOL: 4

115: SET PROGRAMMED MESSAGE Y Y Y Y Y Y NO MESSAGES SELECTED 116: ALARM AND MESSAGE Y Y Y Y Y Y ALARMS SET TO NOTSET 119: SET DISPLAY Y Y Y Y N Y NAME FIRST 121: KEYSET LANGUAGE Y N Y Y Y Y ENGLISH

ALL KEYSETS ‘RING’ RING FREQUENCY DEFAULT=5

CLOCK: 24-HOUR DISPLAY: LOWERCASE

AUTO TIMER: ON HEADSET MODE: OFF HOT KEYPAD: ON KEY TONE: ON PAGE REJOIN: ON RING PREFERENCE: ON CALL COST: OFF AME BGM: OFF AME PSWD: OFF

OFF HOOK RING VOL: 4 HANDSET VOL: 4 SPEAKER VOL: 13 BGM VOL: 13

2-3

DCS DEFAULT DATA COMBINED PROGRAMMING MANUAL NOVEMBER 2001

System Programs

200: OPEN CUSTOMER PROGRAMMING Y Y Y Y Y Y CLOSED (DISABLED) 201: CHANGE CUSTOMER PASSCODE Y Y Y Y Y Y PASSCODE =1234 202: CHANGE FEATURE PASSCODES Y N Y Y Y Y DAY/NIGHT=0000

203: ASSIGN UA DEVICE Y Y Y Y Y Y NONE 204: COMMON BELL CONTROL Y Y Y Y Y Y CONTINUOUS 205: ASSIGN LOUD BELL Y N Y Y Y Y UNASSIGNED 206: BARGE-IN TYPE Y Y Y Y Y Y NO BARGE IN 207: ASSIGN VM/AA PORT Y Y Y Y Y Y NORMAL PORT 208: ASSIGN RING TYPE Y Y Y Y Y Y ICM RING 209: ASSIGN ADD-ON MODULE Y Y Y Y N N NONE FOR MASTER 210: CUSTOMER ON/OFF Y Y Y Y Y Y SEE MMC 210 211: DOOR RING ASSIGNMENT Y Y Y Y Y Y STATION GROUP 500 (or 50) 212: ALARM RINGING STATION Y N Y N N N ALL SENSORS RING 500

213: ALARM MESSAGE Y N Y N N N NONE 214: DISA ALARM RINGING STATION Y Y Y Y Y Y DAY/NIGHT=500 (or 50) 215: VOICE DIALLER OPTIONS Y Y Y N N N 2CH-7USER-20BIN 216: VOICE DIALLER ASSIGNMENTS Y Y Y N N N NONE 217: CCC OPTION N Y N N N N NONE 219: COMMON RELAY SERVICE TYPE N N Y Y Y Y SEE MMC 219 220: ISDN SERVICE TYPE Y Y Y Y N Y VOICE 300: CUSTOMER ON/OFF PER STATION Y Y Y Y Y Y STN CALL PRT : OFF

301: ASSIGN STATION COS Y Y Y Y Y Y DAY CLASS = 1

302: PICKUP GROUPS Y Y Y Y Y Y ALL STATIONS GROUP 1 303: ASSIGN BOSS/SECRETARY Y Y Y Y Y Y NONE 304: ASSIGN STATION/TRUNK USE Y Y Y Y Y Y DIAL = YES

305: ASSIGN FORCED CODE Y Y Y Y Y Y NONE 306: HOT LINE Y Y Y Y Y Y NONE 308: ASSIGN BACKGROUND MUSIC

SOURCE 309: ASSIGN STATION MUSIC ON HOLD Y Y Y Y Y Y NONE 310: LCR CLASS OF SERVICE Y Y Y Y Y Y LEAST COST ROUTING

DCS CI CII 816 408 408i

Y Y Y Y Y Y NONE

DISA ALARM=5678 ALARM CLR=8765 AA RECORD=4321 DECT (BSI) REGISTER =4321

DAY/NIGHT

FWD DLY USE : OFF OTHER FEATURES SET TO ON

NIGHT CLASS = 1

ANS = YES

COS 1

2-4

DCS DEFAULT DATA COMBINED PROGRAMMING MANUAL NOVEMBER 2001

DCS CI CII 816 408 408i

311: ASSIGN SIM PARAMETER Y N N N N N SIM TYPE = DTE

312: ALLOW CLIP Y Y Y Y N Y RCV=YES, SEND=YES,

313: ASSIGN PIN CODE N Y N N N N ALL STATIONS ARE CODE

314: CONFIRM OUTGOING CALL Y N Y Y Y Y NONE 315: SET RELOCATION Y N Y Y Y Y NONE 316: COPY STATION USABLE Y N Y Y N N NONE 317: ASSIGN STATION/STATION USE Y N Y Y N N DIAL=YES 318: DISTINCTIVE RING Y N Y Y Y Y T=F-STN, C=F-STN 319: BRANCH GROUP – – – – – – NOT USED IN UK 400: CUSTOMER ON/OFF PER TRUNK Y Y Y Y Y Y 1A2 EMULATE: OFF

401: C.O./PBX LINE Y Y Y Y Y Y ALL TRUNKS C.O. LINE 402: TRUNK DIAL TYPE Y Y Y Y Y N ALL TRUNKS DTMF 403: TRUNK TOLL CLASS Y Y Y Y Y Y ALL TRUNKS F-STN

404: TRUNK NAME Y Y Y Y Y Y NO NAMES ENTERED 405: TRUNK NUMBER Y Y Y Y Y Y NO NUMBERS ENTERED 406: TRUNK RING ASSIGNMENT Y Y Y Y Y Y ALL TRUNKS DAY/NIGHT:

407: FORCED TRUNK RELEASE Y Y Y Y Y Y NONE 408: ASSIGN TRUNK MUSIC ON HOLD

SOURCE 409: TRUNK STATUS READ Y Y Y Y Y Y SEE MMC 409 410: ASSIGN DISA TRUNK Y Y Y Y Y Y ALL TRUNKS NORMAL 411: ASSIGN E1 SIGNAL TYPE – – – – – – NOT USED IN UK 412: ASSIGN TRUNK SIGNAL Y Y Y N N N IMMEDIATE 414: MPD/PRS SIGNAL Y Y Y Y Y N NONE 415: REPORT TRUNK ABANDON DATA Y Y Y Y N Y REPORT=YES 416: ASSIGN AC15 TRANSLATION Y Y Y N N N UNUSE DID TRANS 417: PRI CRC4 OPTION Y N Y N N N CRC4 ON 418: CARD RESTART Y Y Y Y N Y NONE

Y Y Y Y Y Y TONE

CALL MODE = MANUAL ANS MODE = MANUAL AUTO BAUD = ON DTR CHECK = ON ECHO = ON PROTOCOL = V110 SPEED = 9600 CHAR LENGTH = 8 BITS PARITY = NONE STOP BIT = 1

INFO=CO Tel

TRUNK INC DND: OFF TRUNK FORWARD: ON LCR ALLOW:OFF

DAY/NIGHT

500 (or 50)

2-5

DCS DEFAULT DATA COMBINED PROGRAMMING MANUAL NOVEMBER 2001

DCS CI CII 816 408 408i

419: BRI OPTION Y Y Y Y N Y CHANNEL ANY: YES

420: PRI OPTION Y N Y N N N CHANNEL ANY: YES

421: MSN DIGIT Y Y Y Y N Y NONE 422: ASSIGN TRUNK COS Y Y Y Y Y Y DAY CLASS: 1

423: S/T MODE Y Y Y Y N Y TRUNK 424: S0 MAPPING Y Y Y Y N Y NONE 426: TRUNK GAIN CONTROL Y N Y Y Y Y RX=+0.0 dB, TX=+0.0 dB

427: R2MFC SIGNAL N N N N N N NOT USED IN UK 428: ASSIGN TRUNK/TRUNK USE Y N Y Y N N DIAL=YES 500: SYSTEM-WIDE COUNTERS Y Y Y Y Y Y SEE MMC 500 501: SYSTEM-WIDE TIMERS Y Y Y Y Y Y SEE TABLE OF TIMERS

502: STATION-WIDE TIMERS Y Y Y Y Y Y NO ANS FWD: 015 SEC

503: TRUNK-WIDE TIMERS Y Y Y Y Y Y ANS.BAK TM: 600 MS

504: PULSE MAKE/BREAK RAT IO Y Y Y Y Y N MAKE/BREAK = 33

505: ASSIGN DATE AND TIME Y Y Y Y Y Y FOLLOWS S/W VERSION

506: TONE CADENCE Y Y Y Y Y Y SEE MMC 506 507: ASSIGN AUTO NIGHT TIME Y Y Y Y Y Y NONE 508: CALL COST Y Y Y Y Y Y UNIT COST PER MP: 200

509: C.O. TONE CADENCE N Y N N N N SEE MMC 509 510: SLI RING CADENCE Y Y Y Y Y Y SEE MMC 510 511: MW LAMP CAD Y N Y N N N ON: 1000MS, OFF: 1000MS 512: ASSIGN HOLIDAY Y N Y Y Y Y NONE 600: ASSIGN OPERATOR GROUP Y Y Y Y Y Y DAY/NIGHT: 500 (or 50)

BRI MODE: P-P DDI DLSEND: OVERLAP BRI CODING: A-LAW POWERFEED: NO

PRI MODE: DDI DLSEND: OVERLAP

NIGHT CLASS: 1

(ALL TRUNKS)

AND VALUES IN MMC 501

DTMF DURATION: 100 MS FIRST DGT DELAY: 600 MS

CLEARING: 002 SEC CO SUPV TM: 400 MS DTMF DURATION: 100 MS FIRST DGT DELAY: 600 MS FLASH TIME: 070 MS NO RING TM: 004 SEC PAUSE TIME: 003 SEC PRS DET TM: 000 MS RNG DET.TM: 300 MS WINK: 200 MS MF/DP INT TM: 0800 MS MFR DLY TM: 000 SEC

PULSES PER SECOND = 10

RELEASE DATE

PENCE CALL COST RATE: 100%

2-6

DCS DEFAULT DATA COMBINED PROGRAMMING MANUAL NOVEMBER 2001

DCS CI CII 816 408 408i 601: ASSIGN STATION GROUP Y Y Y Y Y Y SEE MMC 601 602: STATION GROUP NAME Y Y Y Y Y Y NONE 603: ASSIGN TRUNK GROUP Y Y Y Y Y Y SEE MMC 603 604: ASSIGN STATION TO PAGE ZONE Y Y Y Y Y Y NO STATIONS ASSIGNED

605: ASSIGN EXTERNAL PAGE ZONE Y Y Y Y Y Y NONE 606: ASSIGN SPEED BLOCK Y Y Y Y Y Y SYSTEM: SEE MMC 606

607: UCD OPTIONS Y Y Y Y N N SEE MMC 607 608: ASSIGN CLIP REVIEW BLOCK Y Y Y Y N Y ONE BIN OF 10 ENTRIES 700: COPY COS CONTENTS Y Y Y Y Y Y NONE 701: ASSIGN COS CONTENTS Y Y Y Y Y Y TOLL LEVEL: ALL COS=A

702: TOLL DENY TABLE Y Y Y Y Y Y ALL ENTRIES=0 703: TOLL ALLOWANCE TABLE Y Y Y Y Y Y ALL ENTRIES=0 704: ASSIGN WILD CHARACTER Y Y Y Y Y Y ALL X, Y, Z=1 705: ASSIGN SYSTEM SPEED DIAL Y Y Y Y Y Y NONE 706: SYSTEM SPEED DIAL BY NAME Y Y Y Y Y Y NO NAMES 707: AUTHORISATION CODE Y Y Y Y Y Y NONE 708: ACCOUNT CODE Y Y Y Y Y Y NONE 709: PBX ACCESS CODE Y Y Y Y Y Y NONE 710: LCR DIGIT TABLE Y Y Y Y Y Y DEPENDS ON S/W VER-

711: LCR TIME TABLE Y Y Y Y Y Y SEE MMC 711 712: LCR ROUTE TABLE Y Y Y Y Y Y SEE MMC 712 713: LCR MODIFY DIGIT TABLE Y Y Y Y Y Y DEPENDS ON S/W VER-

714: DDI NUMBER AND NAME TRANSLA-

TION

715: PROGRAMMED STATION

MESSAGE

716: UK LCR OPTIONS Y Y Y Y Y Y SEE MMC 716 717: PIN CODE N Y N N N N NONE 718: MY AREA CODE – – – – – – NOT USED IN UK 720: COPY KEY PROGRAMMING Y Y Y Y Y Y NONE 721: SAVE STATION KEY PROGRAMMING Y Y Y Y Y Y RESTORE 722: STATION KEY PROGRAMMING Y Y Y Y Y Y SEE MMC 722 723: SYSTEM KEY PROGRAMMING Y Y Y Y Y Y SEE MMC 723 724: DIAL NUMBERING PLAN Y Y Y Y Y Y SEE MMC 724 725: SMDR OPTIONS Y Y Y Y Y Y SEE MMC 725 726: VM/AA OPTIONS Y Y Y Y Y Y SEE MMC 726

Y Y Y Y N Y SEE MMC 714

Y Y Y Y Y Y 20 MESSAGES (10 PRE-

’ALL ZONE’ IS SET

STATIONS: ONE BIN OF 10 ENTRIES

ALL FEATURES (EXCL. OVERRIDE)=YES

SION

PROGRAMMED) (SEE MMC

715)

2-7

DCS DEFAULT DATA COMBINED PROGRAMMING MANUAL NOVEMBER 2001

DCS CI CII 816 408 408i 727: SYSTEM VERSION DISPLAY Y Y Y Y Y Y INSTALLED CARD VERSIONS 728: CLIP TRANSLATION TABLE Y Y Y Y N Y NONE 730: AA RECORD GAIN Y N Y Y N N +0.0 dB 731: AA RAM CLEAR Y Y Y Y N N NONE 732: AA TRANSLATION TABLE Y Y Y Y N N SEE MMC 732 733: AA PLAN TABLE Y Y Y Y N N SEE MMC 733 734: AA MESSAGE MATCH Y Y Y Y N N MSG INDEX NO. 735: AA USE TABLE Y Y Y Y N N PLAN 01 736: ASSIGN AA MOH Y Y Y Y N N NOT USE 737: DECT SYSTEM CODE Y Y Y N N N AUTH CODE: FFFF

738: DECT CLEAR REGISTRATION Y Y Y N N N FORCED MODE 739: BSI DOWNLOAD Y Y Y N N N NONE 740: STATION PAIR Y Y Y Y N N NONE 741: BSI CARD RESTART Y Y Y N N N NONE 742: BSI STATUS Y Y Y N N N NONE 743: DBS STATUS Y Y Y N N N NONE 744: DECT REGISTRATION ON/OFF Y Y Y N N N DISABLE 745: BSI CARRIER Y Y Y N N N 1111111111 750: VM CARD RESTART Y N Y N N N DOWNLOAD=YES 751: ASSIGN MAILBOX Y N Y N N N ALL STN=YES, ALL GRP=NO 752: AUTO RECORD Y N Y N N N MB=NONE, PORT=NONE

753: WARNING DESTINATION Y N Y N N N DEST=500 754: VM HALT Y N Y N N N NONE 755: VM ALARM Y N Y N N N THRESHOLD=80% 756: ASSIGN VM MOH Y N Y N N N NOT USE 757: VM IN/OUT Y N Y N N N IN/OUT 800: ENABLE TECHNICIAN PROGRAM Y Y Y Y Y Y DISABLE 801: CHANGE TECHNICIAN PASSCODE Y Y Y Y Y Y DEFAULT PASSCODE = 4321 802: CUSTOMER ACCESS MMC NO. Y Y Y Y Y Y SEE MMC 802 803: ASSIGN TENANT GROUP Y N N N N N ALL ASSIGNMENTS TENANT 1 804: SYSTEM I/O PARAMETER Y Y Y Y Y Y SEE MMC 804 805: TX LEVEL AND GAIN Y Y Y Y Y Y SEE MMC 805 806: CARD PRE-INSTALL Y Y Y Y N N NONE 807: VOLUME CONTROL Y Y Y Y Y Y SEE MMC 807 808: T1 TRUNK CODING – – – – – – NOT USED IN UK 809: SYSTEM MMC LANGUAGE Y N Y Y Y Y ENGLISH 810: HALT PROCESSING Y Y Y Y N N NONE 811: RESET SYSTEM Y Y Y Y Y Y NONE 812: SELECT COUNTRY Y N Y Y Y Y NONE

SYSTEM ID: 000

CALL=I

2-8

2.3 System Configuration: Quick Reference

Description DCS Compact I Compact II 816 408 408i

AA card port numbers 3951–8 3951–6 381–61 381–4 N/A N/A AA Translation tables 1 & 2 (entries) 100 100 100 50 N/A N/A Account codes 500 250 200 200 100 100 Authorisation codes 250 100 100 30 10 10 BGM port numbers 3701–2 371–2 371–2 371–2 371 371 CALL keys (max.) 8 8 5 4 2 2 Classes of Service (COS) 30 30 30 10 4 4 CLIP Translation Table entries 250 250 200 200 N/A 100 Daughterboards (keyset) KSU Any DLI port Motherboard None None None

2-9

DDI entries 200 200 200 50 N/A 20 DECT ports 48 24 24 N/A N/A N/A LCR Digit Table (max. entries) 500 500 500 300 100 100 MOH port numbers 3701–2 371–2 371–2 371–2 371 371 Operator Groups (part of Stat ion Group) 1 1 1 1 1 1 Operator Group members (sequential / dis-

tributed ring) Operator Group members (unconditional

ring) Page zones (no. of internal) 4 4 4 4 2 2 Page zones (no. of external) 4 4 4 1 1 1 Pickup Groups 20 20 20 8 4 4 S0 bus ports 32 32 24 16 None 2

32 30 30 16 8 8

32 30 10 16 8 8

2.3 System Configuration: Quick Reference (cont’d)

2-10

Description DCS Compact I Compact II 816 408 408i

Speed dials (total) 1500 500 600 500 300 300 Speed dials (system)(max.) 500 500 500 300 200 200 Station Groups (number of) 30 30 20 10 4 4 Station Group members (sequential / dis-

48 30 30 16 8 8

tributed ring) Station Group members (unconditional

32 30 10 16 8 8

ring) Station Group numbers 500–529 500–529 500–519 500–509 50–53 50–53 Trunk Groups (number of) 11 11 11 4 2 2 Trunk Group members 80 10 40 10 4 4 Trunk Group numbers 9, 80–89 9, 80–89 9, 80–89 9, 80–82 9, 8 9, 8 UCD Groups 102 10

53 34 N/A N/A

Voice dial card port numbers 3551–2 3551–2 355–6 N/A N/A N/A

Notes:

Misc 2 card=381–4, AA card=381 –6, both cards installed=381–90

UCD Group can be created from any Station Group 501 –529 (CI) or last 10 Station Groups 520–529 (DCS)

UCD Group can only be created from last 10 Station Groups 510 –519

UCD Group can only be created from last three Station Groups 507–509

DCS SPECIAL APPLICATIONS COMBINED PROGRAMMING MANUAL NOVEMBER 2001

Part 3. Special Applications

Part 3 provides additional information covering the following topics:

• Voice Mail / Auto Attendant Integration

• Individual Station Page

• CLIP (Calling Line Identification Presentation)

• Toll Restriction (Call Barring) Overview

• S

0 Overview

3-1

DCS SPECIAL APPLICATIONS COMBINED PROGRAMMING MANUAL NOVEMBER 2001

Voice Mail/Auto Attendant Integration

(In-Band / SMDI )

This section focuses mainly on in -band integration. Systems may alternatively accommodate Bellcore standard SMDI—available by setting in MMC 210 (SMDI VMS SET option).

Because of the increased popularity of voice mail and auto attendant use, all DCS systems include many programmable options to address this demand. The degree of integration that can be achieved depends on the abilities of the voice mail/auto attendant (VM/AA) system as well as the telephone system.

The following describes the capabilities provided by systems for voice mail via in-band int egration.

Hardware Provisions

• The VM/AA system must be connected to single line circuits on any SLI card.

• Each port is equipped with a dedicated DTMF receiver for detecting DTMF signa lling

from the VM/AA.

• These ports also provide an instant break in loop current when the calling party hangs up. This is called a disconnect signal.

Software Provisions

• Screened Or Unscreened Transfer

There are no special codes needed to transfer a call. Simply hookflash, receive transfer dial tone and dial the destination.

• Direct In Lines

Any C.O. call can be assigned to ring at an individual station or a station hunt group assigned to the VM/AA.

• Calls or Recalls to the Operator

Dialling 0 will always result in a ringback signal. If the operator is busy, the call continues to ring in queue to the operator.

• Message Waiting A VM/AA port can leave a message at any station or group of stations. The message waiting indication can be set or cancelled at any station or station group with or without the stations ringing.

3–2

DCS SPECIAL APPLICATIONS COMBINED PROGRAMMING MANUAL NOVEMBER 2001

In-Band Signalling

Systems can be programmed to send the calling station’s extension number after the voice mail system answers. These DTMF signals may include a leading digit to indicate the type of call and additional information about the original caller. DTMF signals may also be substituted for call progress tones to speed up voice mail call processing. This program allows call forwarding to a mailbox and bypassing of the main greeting for automatic message retrieval. Blind (unscreened) transfers may be performed because the recall will be correctly identified.

Note: The effectiveness of this program depends on the ability of the voice mail system to make use of this information.

• Station Hunt Group With Overflow

Each station group can have an individual overflow destination with an individual overflow timer. The overflow destination will ring whenever a call to the group is not answered. If the voice mail system becomes inoperative, calls are automatically routed to the overflow destination.

• Internal Call Forwarding to Voice Mail

This option in MMC 300 provides the ability to allow or deny call forwarding of internal calls to voice mail. This feature conserves disk drive space by only storing calls originating outside the system.

• One-Touch Voice Mail Access

One-touch speed dial keys can be programmed to automatically dial, log into and retrieve messages from voice mail.

• Call Progress Tones

The only tones sent to a VM/AA port are dial tone, busy and ringback. To eliminate confusion, busy tone is substituted for DND or error tones on voice mail ports only.

3–3

DCS SPECIAL APPLICATIONS COMBINED PROGRAMMING MANUAL NOVEMBER 2001

Individual Station Page

Keyphone systems were not designed to permit page announcements to individual keysets. However, a forced auto answer key (FAUTO) can be used to do this.

1. Program a keyset for RING in MMC 103.

2. Assign a FAUTO key (in MMC 722) to each keyset that is allowed to page individual keysets.

3. Call another station. When you hear ringback tone, press the FAUTO key. The ringing will stop and an Auto Answer call is set up.

Note: To prevent the use of this feature from getting out of control, only assign FAUTO keys to those keysets needing to page individual keysets.

3–4

DCS SPECIAL APPLICATIONS

low the

COMBINED PROGRAMMING MANUAL NOVEMBER 2001

CLIP

(Calling Line Identification Presentation)

Hardware Provisions

ISDN trunk cards.

Software Provisions

The MMCs related to CLIP are listed below with a short description of their uses. They are listed in the recommended order in which they should be programmed. This sequence is suggested so that the installer/technician gets a better understanding of how the feature works. There is no technical reason to strictly follow this sequence.

l MMC 312

(ALLOW CLIP)

l MMCs 722 and 723

(STATION & SYSTEM KEY PROGRAMMING)

l MMC 728

(CLIP TRANSLATION TABLE)

l MMC 725

(SMDR OPTIONS)

l MMC 119

(SET CLIP DISPLAY)

l MMC 501

(SYSTEM-WIDE TIMERS)

Used to determine which keysets are allowed to receive CLIP displays.

It is strongly recommended that all keysets allowed CLIP in MMC 312 are programmed with a CLIP key using this MMC.

Allows for the creation of a list of names that correspond to numbers received from the Central Office (C.O.). These names will be displayed when a call rings in that has NUMBER ONLY data provided by the C.O.

Provides the ability to print CLIP data and abandoned calls on the Station Message Detail Recording (SMDR) re port.

Station users can determine what CLIP data is displayed when a call rings at the user’s station.

You may need to adjust the CLIP DISPLAY timer. This is the length of time that CLIP data is displayed at u sers’ stations after the CLIP key is pressed.

l MMC 415

(REPORT TRUNK ABANDON DATA)

l MMC 608

(ASSIGN CLIP REVIEW BLOCK)

l MMC 701

(ASSIGN COS CONTENTS)

l MMC 724

(DIAL NUMBERING PLAN)

Used to determine which trunks will record data in the Call Abandon list and print with an Abandon “A” flag on the SMDR report.

Used to assign CLIP Review blocks to keysets to allow the user to review CLIP data for previous calls

All CLIP features are included in this MMC so that the system installer can allow or deny them.

CLIP features are included in this MMC to al system installer to assign an access code where necessary.

3–5

DCS SPECIAL APPLICATIONS COMBINED PROGRAMMING MANUAL NOVEMBER 2001

Toll Restriction (Call Barring)

Overview

The system allows each station to be assigned a class of service (COS) for day and night modes. Into this COS is brought the dialling restrictions to be applied to each station. Dialling restrictions are applied in MMC 702 (Toll Deny Table) and MMC 703 (Toll Allowance Table).

Eight levels of restriction are available to stations: A, B, C, D, E, F, G and H. Level A imposes no restrictions on station dialling; level H restricts stations to internal calls only; and levels B to G are programmable. In addition, the Wild Card Table (MMC 704) can be used to provide more flexibility when programming.

Toll Restriction Ru les

• The Deny Table entries prevent certain numbers being dialled.

• The Allowance Table entries are the ONLY exceptions to the Deny Table entries.

• Listing codes in the Allowance Table with no entries in the Deny Table gives “no

restriction”.

• A wild card in any position in the Deny Table means an exception exists in the Allowance Table for the digits defined by the wild card.

• A wild card at the end of an entry means that more digits may be dialled.

• Never put a single wild card as an entry in the Allowance Ta ble.

• When changing an entry in the BCDEFG status, ALL digits must be entered.

Use of Deny Table

Example

Let’s assume that you want to restrict (bar) the dialling of the following codes to your users: 0860 and 0850 car phone numbers, 0891and 0898 premium rate numbers, 00 International numbers and 01 STD numbers. You would set up the Deny Table as follows:

TOLL DENY TABLE

ENTRY DIGITS B C D E F G

001 0860 1 0 0 0 0 0 002 0850 1 0 0 0 0 0 003 0891 1 1 1 1 0 0 004 0898 1 1 1 1 0 0 005 00 1 1 0 0 0 0 006 01 1 0 0 1 0 0

Note: The number of entries allowed varies between systems (see MMC 702).

From the above table (“1” means a number is barred):

• Stations with Toll Level B applied will be barred all the codes listed.

• Stations with Toll Level C applied will be barred 0891, 0898 and 00 calls.

• Stations with Toll Level D applied will be barred 0891 and 0898 calls.

• Stations with Toll Level E applied will be barred 0891, 0898 and 01 calls.

3–6

DCS SPECIAL APPLICATIONS COMBINED PROGRAMMING MANUAL NOVEMBER 2001

• Stations with Toll Levels F or G applied will have no restrictions.

Use of Wild Cards and the Allowance Table

The Wild Card Table in MMC 704 appears as follows.

WILD CARD 0 1 2 3 4 5 6 7 8 9 * #

X 0 0 0 0 0 0 0 0 0 0 0 0 Y 0 0 0 0 0 0 0 0 0 0 0 0

Z 0 0 0 0 0 0 0 0 0 0 0 0

The digits 0–9, * and # are values that each of the wild cards X, Y and Z can take. This is explained later. (You are also unlikely to use any wild card apart from X.)

In the Deny Table, the STD code 01 has been barred to users with a B or E Toll level. It may, however, be necessary to allow some STD codes to be dialled. For example, the codes 01869, 01993, and 01235 are codes local to Oxford and you may want users in the Oxford area to have access to these codes, with all other STD codes barred. You can achieve this using the Wild Card Table and Toll Allowance Table as follows:

Delete entry 006 in the Deny Table and add the following entry:

TOLL DENY TABLE

ENTRY DIGITS B C D E F G

006 01XXX 1 1 1 1 0 0

and in the Toll Allowance Table make the following entries:

TOLL ALLOWANCE TABLE

ENTRY DIGITS B C D E F G

001 01869 1 1 1 1 0 0 002 01993 1 1 1 1 0 0 003 01235 1 1 1 1 0 0

In the above table, any station assigned a Toll level B, C, D or E will be allowed to dial only 01869, 01993 and 01235 numbers, but all other STD codes will be barred. Stations with a Toll level F or G will be barred from dialling all STD codes.

The changes necessary in the Wild Card Table to implement these requirements are shown below, where the Wild Card character X represents any value between 0 and 9 (i.e. a “1” is placed in the field for any value that X is allowed to represent).

WILD CARD 0 1 2 3 4 5 6 7 8 9 # *

X 1 1 1 1 1 1 1 1 1 1 0 0 Y 0 0 0 0 0 0 0 0 0 0 0 0

Z 0 0 0 0 0 0 0 0 0 0 0 0

3–7

DCS SPECIAL APPLICATIONS COMBINED PROGRAMMING MANUAL NOVEMBER 2001

S0 Overview

Contents

Introduction ..................................................................... 3–9

Specifications ..................................................................3–9

PRI ............................................................................ 3–9

BRI............................................................................ 3–9

ISDN Services .......................................................... 3–10

Installation ...................................................................... 3–12

Operation ....................................................................... 3–12

Ports ....................................................................... 3–12

PRI and BRI LT-T Mode ............................................ 3–13

BRI LT-S Mode .........................................................3–13

Features Reference Tables............................................. 3–14

Related Timers ......................................................... 3–14

PRI and BRI LT-T Port ............................................... 3–14

PRI and BRI LT-S Port ............................................... 3–16

Pin Assignment of Connectors ....................................... 3–16

PRI .......................................................................... 3–16

BRI.......................................................................... 3–16

BRI Related MMC Procedure.......................................... 3–18

3–8

DCS SPECIAL APPLICATIONS COMBINED PROGRAMMING MANUAL NOVEMBER 2001

Introduction

In the DCS there are two line cards for ISDN. One is the PRI card containing one Primary Rate Interface; the other is the BRIN card containing four Basic Rate Interfaces. For Compact (I and II) and 816 systems there are two types of BRI card, one with two BRI access, the other with four.

The following topics are covered:

 Hardware specification of each card  Installation  Operation  ISDN features supported

Note: 1. This document is based on BRI and PRI V2.0 (Nov 4 1996) or later. Therefore, some fe a-

tures are not applicable to the old version.

2. Main CPU software versions required are 4.0 or later (DCS), 2.3 or later (CII), 1.02 or later (816).

Specifications

PRI

(The PRI option is not applicable to Compact I, 816 or 408/408i systems.) The card has the following configuration:

 Contains one PRI access with RJ-45 interface having 120Ω line termination.  Operates in LT-T mode only. You can only connect to a PSTN ISDN Network Termination

Port (NT).

BRI

The different types of BRI card are shown in Table 1.

System Card name Number of

BRI access

DCS BRIN

BRI (old)

Compact II 4BRI

2BRI

Compact I &

816

4BRI 2BRI

Table 1 - BRI cards

4 4 4 2 4 2

Power feeding

to S port

YES

YES YES

NO NO

Note: The only difference between these cards is the number of access, and power feeding capability.

3–9

DCS SPECIAL APPLICATIONS COMBINED PROGRAMMING MANUAL NOVEMBER 2001

Each BRI / BRIN access has the following features:

 Each port operates in either LT-T or LT-S mode. Every setting is done by MMC - there is

no jumper or DIP switch to set. You can connect an NT line or ISDN terminals. (See note, below.)

 For LT-S ports, you can decide whether or not power is supplied to that port by MMC

419.

 32 numbers (DCS—range 7801 to 7832) or 24 numbers (Compact II—range 7801 to

7824) are reserved for terminals attached to the LT-S ports. Each number can be assigned to only one port. However, a port can have more than one number. (That is, two ISDN terminals with the same MSN number cannot exist in different LT -S ports.)

 Each S0 bus must be terminated with a 100Ω termination resistor. The original BRI cards

did not have this resistor. However, it is fitted to cards manufactured from mid 1997. It is important that this termination is present on each installation, and should be checked by the installer.

Note: 1. In BRI, LT -T and LT-S mode can be selected only by MMC programming. However, you

should connect the Tx and Rx cable pair from the MDF correctly. Tx and Rx connections are reversed between LT-T and LT-S mode (see Table 15).

2. If you are connecting a T0 port to an NT, take care if there is a termination present some-

where other than on the BRI card on the bus.

ISDN Services

Outgoing calls when origination party is non-S 0 terminal

When an extension seizes an ISDN TRK or S0 terminal attached to the system, the ISDN bearer capability (BC) and high layer compatibility (HLC) will be coded as in Table 2.

ORIGINATION BC HLC

DGP (Digital keyphone) Speech Telephony SLT (ICM/CO ring in MMC 208) 3.1 kHz Audio Telephony SLT (DATA ring in MMC 208) 3.1 kHz Audio Telephony

Table 2 - Coding of BC/HLC when an extension seizes an

ISDN TRK or S0 terminal

Incoming calls when destination party is non-S0 terminal

When an incoming call is present on the ISDN TRK or S0 port, the call will be accepted if the following condition is satisfied (Table 3). Calls with other BC or HLC will be rejected.

3–10

DCS SPECIAL APPLICATIONS COMBINED PROGRAMMING MANUAL NOVEMBER 2001

BC HLC DESTINATION

Speech Telephony DGP (Digital keyphone)

SLT (ICM/CO ring in MMC 208)

3.1 kHz Audio Telephony SLT (ICM/CO ring in MMC 208)

3.1 kHz Audio None DGP SLT (ICM/CO ring in MMC 208)

3.1 kHz Audio Fax G2/3 SLT (DATA ring in MMC 208)

Table 3 - Accepted BC and HLC when destination is a non-S0 terminal

Accepted BC and HLC combinations on the ISDN TRK or S0 port

For calls between S0 and ISDN TRK, the following BC and HLC combinations (Table 4) will be accepted, regardless of which party is the originator.

BC HLC LLC

Speech Telephony A-law

3.1 kHz Audio Telephony A-law

3.1 kHz Audio none A-law

3.1 kHz Audio Fax G2/3 A-law Unrestricted Digital Info none none Unrestricted Digital Info Teletex none Unrestricted Digital Info OSI none Unrestricted Digital Info Video New none Unrestricted Digital Info Mixed none

56 kHz Data none none

V.110 none proper value V.120 none proper value Video none none

7 kHz Audio none none

Unrestricted Digital Info Fax G4 Fax G4

Table 4 - Accepted BC and HLC when destination is a non-S0 terminal

Supported bearer capability

Speech, Unrestricted Data, 3.1 kHz Audio, 7 kHz Audio, Video

Supported high layer compatibility

Telephony, G3 Fax, G4 Fax, Mixed Mode, Teletex, Videotex, Telex, OSI.

3–11

+ 246 hidden pages