Samsung CS-53140TS, CS-21K40MG User Manual

COLOR TELEVISION

CS21K40

Owner’s Instructions

Before operating, please read this manual thoroughly, and retain it for future reference.

Register your product at

www.samsung.com/global/register

Control Panel(depending on the model)

The actual configuration of your TV may be different, depending on your model.

Front (or Side) Panel

1 On-screen menu display

2 Volume adjustment

3 Channel selection

4 Remote control sensor

5 Standby indicator

6Power on/off

You can use the 3 buttons to switch the TV on when it is in standby mode depending on the model.

The 2 and 3 buttons also have the same function as the œ/√/†/… buttons on the remote control.

If the remote control no longer works or you have misplaced it, you can use the controls on the panel of the television.

Connection Panel(depending on the model)

The actual configuration of your TV may be different, depending on your model.

Rear Panel

or

cable television network

Whenever you connect an audio or video system to your television, ensure that all elements are switched off. Please be sure to match the color coded input terminals and cable jacks.

Connecting to an Aerial or Cable Television Network

Connect the aerial or network input cable to the 1 (75 Ω coaxial socket).

To view television channels correctly, a signal must be received by the set from one of the sources: an outdoor aerial, cable television network, or satellite network.

If you are using an indoor aerial, you may need to adjust it when tuning your television until you obtain a picture that is both sharp and clear.

Connecting to the SCART Input/Output

The SCART2 connectors are used for equipment, such as a VCR, DVD, decoder, satellite receiver, video game device, or video disc player.

The SCART2 is also used for equipment with an RGB output, such as a video game device or video disc player.

continued...

English - 1

Connecting to the RCA Output

The RCA4 connectors are used for equipment, such as a recording VCR or audio system.

Connecting to the RCA Input

The RCA3 connectors are used for equipment, such as a VCR, DVD, decoder, satellite receiver, video game device, or video disc player. (When using the mono equipment, connect to the AUDIO-L input connector.)

The RCA5 connectors are used for equipment such as a DVD with component output (480i only).

Front (or Side) Panel

Audio input

Video input

Headphone jack

Please be sure to match the color coded input terminals and cable jacks.

Connecting to the RCA Input

The 1 (AUDIO-L/R) and 2 (VIDEO) connectors are used for equipment, such as a camcorder, video disc player, or video game device.

Connecting Headphones

The 3 (headphone) jack is used for watching a television programme without disturbing the other people in the room. Prolonged use of headphones at a high volume may damage your hearing.

When both the front (or side) AV and rear connectors are connected to external equipment, the front (or side) AV receives priority.

AA68-03808E-01

Remote Control(depending on the model)

Operation of remote control may be affected by bright artificial light near to the TV.

1POWER

Used to switch the TV on and off.

2Numeric buttons

Used to select channels directly.

3-/--

Used to select a channel numbered ten or over. Press this button, then “--” symbol is displayed. Enter the two-digit channel number.

4

/

Used to increase or decrease the volume.

5MENU

Used to display the onscreen menu or return to the previous menu.

6… / † / œ / √

Used to control the cursor in the menu.

7S.MENU

Used to display the sound menu.

8TURBO

Used to select the turbo sound option.

9P.SIZE

Used to change the screen size.

0DUAL I-II (option) Used to select the sound mode.

!SOURCE

Used to display all of the available video sources.

@INFO

Used to view the channel information and setting status you selected.

#PRE-CH

Used to switch repeatedly between the last two channels displayed.

$P /

Used to display the next or previous stored channel.

%EXIT

Used to exit from any display or return to normal viewing.

^MUTE

Used to switch the sound off temporarily. To turn the sound back on, press the MUTE, , or button.

&ENTER

While using the onscreen menus, press the ENTER button to activate (or change) a particular item.

*S.MODE (option) Used to select the sound effect.

(P.MODE

Used to select the picture effect.

)TV

Used to return to the TV mode when it is in external input mode.

aSLEEP

Used to select a preset time interval for automatic shut off.

Installing Batteries

Remove the cover. Install two AAA size batteries, then replace the cover. When the remote control does not operate normally, check that the “+”

and “-” ends of the batteries are

inserted correctly or the batteries are drained.

Do not mix battery types, i.e. alkaline and manganese.

English - 2

Switching theTelevision On and Off

The mains lead is attached to the rear of the television.

1Plug the mains lead into an appropriate socket.

The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.

2Press the “I” button (On/Off) on the front (or side) of the television.

3Press the POWER button on the remote control to switch the television on. The programme that you were watching last is re-selected automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Channel - Auto Store” or “Channel - Manual Store” on page 4.

If the television is initially powered on, several basic customer settings proceed automatically. Refer to “Function - Plug & Play” on page 3.

4To switch the television off, press the “I” button (On/Off) on the front (or side) of the television.

Placing theTelevision in Standby Mode

The television can be placed in standby mode, in order to reduce power consumption and wear of the cathode ray tube. Standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).

1Press the POWER button on the remote control while viewing.

The television is in standby mode.

2To switch the television back on, simply press it again.

Do not leave the television in standby mode for long periods of time (when you are away on holiday, for example). Turn the television off by pressing the “I” button (On/Off) on the front (or side) of the television. It is best to unplug the set from the mains and aerial.

ENJOY YOUR WATCHING

Plug & Play

Viewing the Menus

1Press the MENU button.

The main menu is displayed on the screen. Its left side has four icons: Picture, Sound, Channel, and

Function.

2Press the … or † button to select one of the icons. Press the œ or √ button to access the icon’s sub-menu.

3Press the … or † button to move to items in the menu. Press the œ or √ button to enter items in the menu.

4Press the …/†/œ/√ button to change the selected items. Press the MENU button to return to the previous menu.

5Press the EXIT button to exit from the menu.

Function - Plug & Play

When the television is initially powered on, several basic customer settings proceed automatically and subsequently. The following settings are available.

1 If the television is in standby mode, press the POWER

button on the remote control.

The Plug & Play is displayed. It flickers for a little while, and then Language menu is displayed.

2 Select the appropriated		LANGUAGE
language by pressing the		ENGLISH
		FRANÇAIS
… or † button. Press the
		TÜRKÇE
MENU button.
The Ant. Input Check		Adjust	Select
is displayed.
		Ant. Input Check
If any language is not
selected, the language		Auto Store	Exit
menu will disappear about 30 seconds later.

3Make sure that the antenna is connected to the television (refer to page 1).

4 Press the œ or √ button to
			P 1
search the channels. The			471 MHz	48%
searching starts. To stop the
search, press the MENU
			Exit
button.

continued...

5 When the channel	Time
searching has finished, the	Clock	-- : -- am
Time menu is displayed
with Clock selected.	Move	Exit

6Press the œ or √ button to move to the hour or minute. Set the hour or minute by pressing the … or † button.

7 When you have finished, press the MENU button.

The ENJOY YOUR WATCHING is displayed, and then the channel which has been stored will be activated.

Re-setting the Plug & Play				Function
Method: MENU …/†
		Language : English
(Function) œ/√ …/†		Time		√
		Plug & Play		√
(Plug & Play) œ/√		Blue Screen		: Off
		Child Lock		√
		Low Noise Amp		: Off
	Select Enter			Exit

English - 3