Samsung CS-34Z6HR User Manual [en, ms]

COLOUR TELEVISION

29Z4/34Z4 29Z6/32Z6/34Z6 29Z7/32Z7/34Z7

Owner’s Instructions

Before operating the unit,

please read this manual thoroughly,

and retain it for future reference.

ON-SCREEN MENUS

DIGITAL 100Hz

TELETEXT

ENG

Safety Instructions

◆ Do not expose the television to extreme temperature conditions or to extreme humidity conditions.

◆ Do not expose the television to direct sunlight and other sources of heat.

◆ Do not expose the television to any liquids.

◆ Never put objects of any kind into the television, and do not place a water-containing vessel on the

television.

◆ During a storm conditions (especially when there is lightning) unplug the television from the mains socket and aerial.

◆ Do not step on or twist the power cord.

◆ Do not overload wall outlets or extension cords as this can result in a risk of fire or electric shock.

◆ Please use a soft and dry cloth (not containing volatile matter) when you clean the TV.

◆ If the television is broken, do not try to repair it yourself. Contact qualified service personnel.

◆ If the remote control is not used for a long period of time, remove the batteries and store it in a

cool, dry place.

◆ Do not drop the remote control.

This device is not for use in industrial environments.

Caution

WARNING: TO PREVENT DAMAGE WHICH MAY RESULT

IN FIRE OR SHOCK HAZARD. DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION: TO PREVENT ELECTRICAL SHOCK,

DO NOT REMOVE REAR COVER, NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

The lightning flash and arrow head within the triangle is a warning sign alerting you of “dangerous voltage” inside the product.

The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product.

☛

The main voltage is indicated on the rear of the TV set and the frequency is 50 or 60Hz.

ENG

Contents

◆ FOREWORD

■ Safety Instructions ......................................................................................... 2

■ Caution .......................................................................................................... 2

◆ CONNECTING AND PREPARING YOUR TELEVISION

■ View of Control Panel .................................................................................... 5

■ View of Connection Panel ............................................................................. 6

■ Infrared Remote Control ................................................................................ 7

■ Inserting the Batteries in the Remote Control................................................ 8

■ Connecting to an Aerial or Cable Television Network ................................... 9

■ Switching Your Television On and Off........................................................... 10

■ Placing Your Television in Standby Mode..................................................... 10

■ Becoming Familiar with the Remote Control ................................................. 11

■ Plug & Play Feature....................................................................................... 12

■ Viewing the Demonstration............................................................................ 13

■ Choosing Your Language.............................................................................. 13

◆ SETTING THE CHANNELS

■ Storing Channels Automatically..................................................................... 14

■ Sorting the Stored Channels ......................................................................... 15

■ Storing Channels Manually............................................................................ 16

■ Assigning Names to Channels ...................................................................... 18

■ Skipping Unwanted Channels ....................................................................... 19

■ Fine Tuning Channel Reception.................................................................... 20

◆ USING YOUR TELEVISION

■ Changing the Picture Standard ..................................................................... 21

■ Adjusting the Picture Settings........................................................................ 22

■ Extra Picture Settings

(Scan mode / Digital NR / Tilt / LNA) ............................................................. 23

■ Setting the Blue Screen................................................................................. 24

■ Selecting the Picture Size.............................................................................. 24

■ Freezing the Current Picture ......................................................................... 24

■ Changing the Sound Standard ...................................................................... 25

■ Adjusting the Sound Settings ........................................................................ 26

■ Selecting the Turbo Sound............................................................................ 26

■ Extra Sound Settings

(Auto volume / Melody / Pseudo stereo / Virtual surround) ........................... 27

■ Selecting the Sound Mode (depending on the model) .................................. 28

ENG

Contents (continued)

◆ USING YOUR TELEVISION (continued)

■ Setting the Sleep Timer ................................................................................. 29

■ Setting and Displaying the Current Time....................................................... 30

■ Switching the Television On and Off Automatically ....................................... 31

■ Viewing the Picture In Picture (PIP) : Option................................................. 32

◆ USING THE TELETEXT FEATURE

■ Teletext Feature ............................................................................................ 34

■ Displaying the Teletext Information ............................................................... 34

■ Selecting a Page by Number......................................................................... 35

■ Using FLOF to Select a Page........................................................................ 36

■ Storing Teletext Pages .................................................................................. 37

◆ ADDITIONAL INFORMATION ON CONNECTIONS

■ Connecting to the External Input/Outputs...................................................... 38

■ Connecting to the DVD Player or Digital Set-Top Box .................................. 39

■ Connecting to the Audio Output .................................................................... 39

■ Connecting to the RCA Input......................................................................... 40

■ Connecting to the S-Video Input.................................................................... 40

■ Connecting Headphones............................................................................... 41

■ Viewing Pictures From External Sources ...................................................... 41

◆ RECOMMENDATIONS FOR USE

■ Automatic Degaussing to Remove Colour Patches....................................... 42

■ Troubleshooting: Before Contacting Service Personnel................................ 42

☛

➢

Press Important Note

Symbols

View of Control Panel (depending on the model)

ENG

➣

Using the Buttons on the Panel

If the remote control no longer works or you have lost it, you can use controls on the panel of the TV to:

◆ Switch on the TV when it is in Standby mode and select channels ( ▲ CH ▼ )

◆ Access the menu ( MENU )

◆ Adjust the volume ( + VOL -)

◆ Switch among Video input modes ( TV/VIDEO )

Œ POWER ON/OFF

´ REMOTE CONTROL SENSOR

ˇ STANDBY INDICATOR

INPUT SOURCE SELECTION

MENU DISPLAY

VOLUME INCREASE

∏

VOLUME DECREASE

”

NEXT CHANNEL

’

PREVIOUS CHANNEL

29Z4/34Z4

29Z6/32Z6/34Z6

View of Connection Panel

ENG

AUDIO INPUT (R, L)

VIDEO INPUT

S-VIDEO INPUT

HEADPHONE CONNECTOR

AUDIO/VIDEO MONITOR OUTPUT

SUB-WOOFER SPEAKER OUTPUT

(29Z7/32Z7/34Z7)

75Ω COAXIAL CONNECTOR FOR AERIAL/CABLE NETWORK

AUDIO/VIDEO INPUT 2

COMPONENT INPUT 1

Side of the TV

ANT IN

Rear of the TV

➣

Available format for Component Inputs; 480i/480p/1080i-60Hz

AUDIO/VIDEO INPUT 1

AUDIO/VIDEO INPUT 3

COMPONENT INPUT 2

Infrared Remote Control

ENG

➢

The performance of the remote control may be affected by bright light.

TELEVISION STAND-BY

ONE/TWO-DIGIT CHANNEL

SELECTION/

TELETEXT PAGE HOLD

TURBO SOUND

TUNER OR CABLE NETWORK

SELECTION

VOLUME DECREASE

NEXT CHANNEL/

TELETEXT NEXT PAGE

AUTOMATIC SWITCH-OFF/

TELETEXT STORE

TEMPORARY SOUND SWITCH-OFF

EXTERNAL INPUT SELECTION/ TELETEXT MODE SELECTION (LIST/FLOF)

ON-SCREEN DISPLAY/ TELETEXT REVEAL

DIRECT CHANNEL SELECTION

PICTURE SIZE/

TELETEXT SIZE SELECTION

PREVIOUS CHANNEL\ TELETEXT PREVIOUS PAGE

VOLUME INCREASE

PICTURE EFFECT SELECTION

STILL PICTURE

SOUND MODE SELECTION/ TELETEXT SUB-PAGE

MENU DISPLAY/ PROGRAMME SELECTION BY NAME

PICTURE MENU DISPLAY

SOUND EFFECT SELECTION

SOUND MENU DISPLAY

(EQUALIZER)

VCR OR DVD FUNCTIONS;

- STOP

- REWIND

- PLAY/PAUSE

- FAST FORWARD

PIP FUNCTIONS (OPTION);

- PIP ON/OFF

- INTERCHANGE THE MAIN AND SUB PICTURE (SWAP)

- STILL

- SIZE SELECTION (SIZE)

- LOCATION SELECTION (LOCATE)

- SCAN

- SOURCE SELECTION (TV/VIDEO)

- CHANNEL SELECTION (P

▲/▼)

FASTEXT TOPIC SELECTION

MAKE THE REMOTE CONTROL WORKS FOR TV, VCR, CABLE, DVD PLAYER.

➣

The remote control might not be compatible with the TV manufactured by another company.

TELETEXT DISPLAY/

MIX BOTH TELETEXT INFORMATION

AND THE NORMAL BROADCAST

PIP

You must insert or replace the batteries in the remote control when you:

◆ Purchase the television

◆ Find that the remote control is no longer operating

correctly

1 Remove the cover on the rear of the remote control by pressing

the symbol downwards and then pulling firmly to remove it.

2 Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking

care to respect the polarities:

◆-on the battery against -on the remote control

◆+on the battery against +on the remote control

3 Replace the cover by aligning it with the base of the remote

control and pressing it back into place.

Inserting the Batteries in the Remote Control

ENG

To view television channels correctly, a signal must be received by the set from one of the following sources:

◆ An outdoor aerial

◆ A cable television network

◆ A satellite network

1 In the first three cases, connect the aerial or network input cable to

the 75Ω coaxial socket on the rear of the television.

2 If you are using an indoor aerial, you may need to turn it when

tuning your television until you obtain a picture that is both sharp and clear. For further details, refer to:

◆ “Storing Channels Automatically ” on page 14

◆ “Storing Channels Manually” on page 16

ENG

Rear of the TV

Cable Television

Network

Connecting to an Aerial or Cable Television Network

ENG

The mains lead is attached to the rear of your television.

1 Plug the mains lead into an appropriate socket.

➢

The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.

2 Press the “” button (On/Off) on the front of the television.

Result

: The Standby indicator on the front of the television

lights up.

3 Press the POWER ( ) button on the remote control to switch the

television on.

Result

: The programme that you were watching last is re-

selected automatically.

➣

If you have not yet stored any channels, No clear picture appears. Refer to “Storing Channels Automatically” on page 14 or “Storing Channels Manually” on page 16.

4 To switch your television off, press the “”button (On/Off) again.

Placing Your Television in Standby Mode

Your television can be placed in Standby mode, in order to reduce:

◆ Power consumption

◆ Wear of the cathode ray tube

The Standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).

1 Press the POWER ( ) button on the remote control.

Result

: The screen is turned off and the Standby indicator on

the front of the television lights up in red.

2 To switch the television back on, simply press the POWER ()

button again.

☛

Do not leave your television in Standby mode for long periods of time (when you are away on holiday, for example). Turn your television off by pressing the “” button (On/Off) on the front of the television. It is best to unplug the set from the mains and aerial.

Switching Your Television On and Off

The remote control is used mainly to:

◆ Change channels and adjust the volume

◆ Set up the television using the on-screen menu system

The following table presents the most frequently used buttons and their functions.

Button Viewing Function Menu Function

Used to display the next Used to select the previous

P stored channel. menu option.

P Used to display the Used to select the next menu

previous stored channel. option.

to Used to display the corresponding channels.

-/--

Used to select a channel numbered ten or over. Press this button, and the “

” symbol is displayed.

Enter the two-digit channel number.

Used to decrease the Used to... volume.

◆ Display a submenu containing selections for the current menu option.

◆ Search backwards manually for channels

◆ Reduce a menu option value.

Used to increase the Used to... volume.

◆ Display a submenu containing selections for the current menu option.

◆ Search forwards manually for channels

◆ Increase a menu option value.

MUTE Used to switch the sound off temporarily.

➣

To turn the sound back on, press this button again, or press the

or + button.

MENU Used to display the Used to return to the previous

on-screen menu system. menu or normal viewing.

TV Used to switch the Used to exit from the menu

television on when it is system and return to normal in Standby mode. viewing directly.

Becoming Familiar with the Remote Control

ENG

PIP

ENG

When the television is initially powered on, three basic customer settings proceed automatically and subsequently: setting the language, channel and clock.

1 If the television is in Standby mode, press the POWER ( ) button

on the remote control.

Result

: The message Plug & Play is displayed. It flickers for

a little while and then

Language menu is automatically

displayed.

2 Select the appropriate language by pressing the or

button. Press the

MENU button to enter the language.

Result

: The message Ant. Input : Check is displayed.

➣

If any language is not selected on the Language menu, the Language menu will disappear about 30 seconds later.

3 Make sure that the antenna is connected to the TV. Press the

+ button.

Result

: The

Auto store menu is displayed with Area is

selected.

4 Select your area by pressing the

or + button. To search the

channels, select

Search by pressing the or button, and

then press the

or + button. Press the MENU button to stop the

search.

Result

: The

Time menu is displayed with Clock is selected.

➣

Refer to “Storing Channels Automatically” on page 14.

5 Press the

or + button to move to the hour or minute. Set the

hour or minute by pressing the or button.

➣

Refer to “Setting and Displaying the Current Time” on page

30.

6 When you have finished, press the MENU button.

Result

: The message ENJOY YOUR WATCHING is displayed,

and then the channel which has been stored will be activated.

7 If you want to reset this feature...

1 Press the MENU button.

2 Press the or button to select Function, and then

press the

or + button.

3 Select Plug & Play by pressing the or button, and

then press the

or + button.

Result

: This feature starts with the message

Plug & Play

is displayed.

Plug & Play Feature

Plug & Play

Ant. Input : Check

Select Exit

Select Adjust Exit

Time

Clock : -- : -- am Timer : Off

Select Enter Exit

Function

Language : English Time

❿❿

Plug & Play

❿❿

Blue screen : On Demonstration

❿❿

ENJOY YOUR WATCHING

Select Adjust Exit

Auto store

Area : ASIA W/EUROPE Search : -/+

To become familiar with the various menus provided by your television, you can view the inbuilt demonstration.

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the or button to select Function.

Result

: The options available in the Function group are

displayed.

3 Press the

or + button.

4 Press the or button to select Demonstration.

5 Press the

or + button.

Result

: Each of the menu options is displayed in turn.

➣

When you wish to exit from the demonstration, press the TV button on the remote control.

When you start using your television for the first time, you must select the language which will be used for displaying menus and indications.

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the or button to select Function .

Result

: The options available in the Function group are

displayed.

3 Press the

or + button.

Result

: The Language is selected.

4 Select the appropriate language by pressing the

or + button

repeatedly.

Viewing the Demonstration

Choosing Your Language

ENG

Select Enter Exit

Function

Language : English Time

❿❿

Plug & Play

❿❿

Blue screen : On Demonstration

❿❿

Select Adjust Exit

Function

Language : English Time

❿❿

Plug & Play

❿❿

Blue screen : On Demonstration

❿❿

ENG

You can scan for the frequency ranges available to you (and availability depends on your country). Automatically allocated programme numbers may not correspond to actual or desired programme numbers. However you can sort numbers manually and clear any channels you do not wish to watch.

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the or button to select Channel.

Result

: The options available in the Channel group are

displayed.

3 Press the

or + button.

Result

: The Auto store is selected.

4 Press the

or + button again.

Result

: The options available in the Auto store group are

displayed with

Area is selected.

5 Select your area by pressing the

or + button. The areas are

displayed in the following order:

ASIA W/EUROPE-CIS E/EUROPE

CHINA-HONGKONG U/K-AUSTRALIA-NZ/INDONESIA-SOUTH

AFRICA

AMERICA.

6 Press the or button to select Search.

7 Press the

or + button to start the search.

Result

: The horizontal bar is displayed, and then channels are

stored in an order which reflects their positions in the frequency range. Finally, the search will end automatically.

➢ To stop the search before it has finished, press the MENU

button.

8 When searching and storing are complete, the Sort menu is

displayed.

◆

To sort the stored channels into the desired numerical order, go to Step

6 of the “Sorting the Stored Channels” procedure

on page 15.

◆

To exit from the channel store function without sorting the channels, press the

MENU button repeatedly until the menus

disappear.

9 When the channels have been stored, you can:

◆

Sort them in the order required (refer to page 15)

◆

Assign a name to the stored channels (refer to page 18)

◆

Clear a channel (refer to page 19)

◆

Fine tune channel reception if necessary (refer to page 20)

◆

Activate the Digital Noise Reduction feature (refer to page 23)

Storing Channels Automatically

Select Adjust Exit

Auto store

Area : ASIA W/EUROPE Search : -/+

Select Enter Exit

Channel

Auto store

❿❿

Manual store

❿❿

Name

❿❿

Add/Erase

❿❿

Fine tune

❿❿

Sort

❿❿

Select Search Exit

Auto store

Area : ASIA W/EUROPE Search : -/+

Exit

P 1 106 MHz 7 %

Select Adjust Exit

Sort

From : P 1 To : P-Store : ?

+ 30 hidden pages