Samsung CS-29M21PH, CS-25M21EN, CS-25M21EH, CS-21M21EN User Manual
COLOR TELEVISION
Owner’s Instructions
Before operating, please read this manual thoroughly,
and retain it for future reference.
Register your product at
www.samsung.com/global/register
Connection Panel
The actual configuration of your TV may be different,
➢
depending on your model.
Rear Panel
(depending on the model)
Connecting to the RCA Input
The RCA¨ and RCAˆ connectors are used for equipment,
such as a VCR, DVD, decoder, satellite receiver, video game
device, or video disc player. (When using the mono
equipment, connect to the AUDIO-L input connector.)
The RCA∏ connectors are used for equipment such as a
DVD with component output (480i only).
Connecting to the RCA Output
The RCAØ connectors are used for equipment, such as a
recording VCR or audio system.
or
Control Panel
The actual configuration of your TV may be different,
➢
depending on your model.
Front (or Side) Panel
ΠInput source selection
´ On-screen menu display
ˇ Volume adjustment
¨ Channel selection
ˆ Standby indicator
Ø Remote control sensor
∏ Power on/off
◆ You can use the ¨ buttons to switch the TV on when it is
in standby mode depending on the model.
◆ The ˇ and ¨ buttons also have the same function as the
œ/√/…/† buttons on the remote control.
◆ If the remote control no longer works or you have
misplaced it, you can use the controls on the panel of the
television.
(depending on the model)
cable television network
Whenever you connect an audio or video system to your
☛
television, ensure that all elements are switched off.
Please be sure to match the color coded input terminals
and cable jacks.
Connecting to an Aerial or Cable Television Network
Connect the aerial or network input cable to the Œ (75 Ω
coaxial socket).
To view television channels correctly, a signal must be
received by the set from one of the sources: an outdoor
aerial, cable television network, or satellite network.
If you are using an indoor aerial, you may need to adjust it
when tuning your television until you obtain a picture that is
both sharp and clear.
Connecting to the SCART Input/Output
The SCART´ and SCARTˇ connectors are used for
equipment, such as a VCR, DVD, decoder, satellite receiver,
video game device, or video disc player.
The SCART´ is also used for equipment with an RGB
output, such as a video game device or video disc player.
continued...
Front (or Side) Panel
ΠAudio input
´ Video input
ˇ S-Video input
¨ Headphone jack
Please be sure to match the color coded input terminals
☛
and cable jacks.
Connecting to the RCA Input
The Œ (AUDIO-L/R) and ´ (VIDEO) connectors are used
for equipment, such as a camcorder, video disc player, or
video game device.
Connecting to the S-VIDEO Input
The ˇ (S-VIDEO) and Œ (AUDIO-L/R) connectors are used
for equipment with an S-Video output, such as a camcorder
or VCR.
Connecting Headphones
The ¨ (headphone) jack is used for watching a television
programme without disturbing the other people in the room.
Prolonged use of headphones at a high volume may damage
your hearing.
When both the front (or side) AV and rear connectors
➢
are connected to external equipment, the front (or
side) AV receives priority.
English - 1
AA68-03629A-00
Remote Control
Operation of remote control may be affected by bright
➢
artificial light near to the TV.
ŒŒ
POWER
Used to switch the TV
on and off.
´´
DUAL I-II
Used to select the
sound mode.
ˇˇ
P.SIZE
Used to change the
screen size.
¨¨
Numeric buttons
Used to select channels
directly.
(depending on the model)
ˆˆ
-/--
Used to select a channel
numbered ten or over.
Press this button, then
“--” symbol is
displayed. Enter the
two-digit channel
number.
ØØ
MUTE
Used to switch the
sound off temporarily. To
turn the sound back on,
press the MUTE, , or
button.
∏∏
””
’’
˝˝ …… / †† / œœ / √√
ÔÔ
ÒÒ
ÚÚ
Installing Batteries
Remove the cover. Install two AAA
size batteries, then replace the cover.
When the remote control does not
operate normally, check that the “+” and “-” ends of the
batteries are inserted correctly or the batteries are drained.
➢
/
Used to increase or
decrease the volume.
TV
Used to return to the TV
mode when it is in
external input mode.
MENU
Used to display the onscreen menu or return to
the previous menu.
Used to control the
cursor in the menu.
TURBO
Used to select the turbo
sound option.
S.MENU
Used to display the
sound menu.
SLEEP
Used to select a preset
time interval for
automatic shut off.
PRE-CH
Used to switch
repeatedly between the
last two channels
displayed.
Do not mix battery types, i.e. alkaline and manganese.
ÆÆ
VIDEO
Used to display all of the
available video sources.
ıı
P/
Used to display the next
or previous stored
channel.
˜˜
INFO
Used to view the
channel information and
setting status you
selected. (Depending on
the model, the signal
strength symbol ( )
can be displayed.)
¯¯
EXIT
Used to exit from any
display or return to
normal viewing.
˘˘
ENTER
While using the onscreen menus, press the
ENTER button to
activate (or change) a
particular item.
¿¿
P. MODE
Used to select the
picture effect.
¸¸
S.MODE
Used to select the
sound effect.
Switching the Television On and Off
The mains lead is attached to the rear of the television.
1 Plug the mains lead into an appropriate socket.
The main voltage is indicated on the rear of the
➢
television and the frequency is 50 or 60Hz.
2 Press the button (On/Off) on the front (or side) of the
television.
3 Press the POWER button on the remote control to
switch the television on. The programme that you were
watching last is re-selected automatically. If you have
not yet stored any channels, no clear picture appears.
Refer to “Channel - Auto Store” or “Channel - Manual
Store” on page 4.
If the television is initially powered on, several basic
➢
customer settings proceed automatically. Refer to
“Setup - Plug & Play” on page 3.
4 To switch the television off, press the button (On/Off)
on the front (or side) of the television.
Placing the Television in Standby Mode
The television can be placed in standby mode, in order to
reduce power consumption and wear of the cathode ray
tube. Standby mode can be useful when you wish to
interrupt viewing temporarily (during a meal, for example).
1 Press the POWER button on the remote control while
viewing.
The television is in standby mode.
2 To switch the television back on, simply press it again.
Do not leave the television in standby mode for long
☛
periods of time (when you are away on holiday, for
example). Turn the television off by pressing the
button (On/Off) on the front (or side) of the television. It
is best to unplug the set from the mains and aerial.
English - 2
Viewing the Menus
1 Press the MENU button.
The main menu is displayed on the screen. Its left side
has five icons: Input, Picture, Sound, Channel, and
Setup.
2 Press the … or † button to select one of the icons.
Press the ENTER button to access the icon’s sub-menu.
3 Press the … or † button to move to items in the menu.
Press the ENTER button to enter items in the menu.
4 Press the …/†/œ/√ button to change the selected
items. Press the MENU button to return to the previous
menu.
5 Press the EXIT button to exit from the menu.
Setup - Plug & Play
When the television is initially powered on, several basic
customer settings proceed automatically and subsequently.
The following settings are available.
1 If the television is in standby
mode, press the POWER
button on the remote
control.
The Plug & Play is
displayed. It flickers for a
little while, and then
Language menu is
displayed.
Plug & Play
Language
English
Melayu
Indonesia
Move Enter
continued...
2 Select the appropriated
language by pressing the …
or † button. Press the
Check antenna input
Enter Exit
ENTER button.
The Check antenna input is displayed.
If any language is not selected, the language menu
➢
will disappear about 30 seconds later.
3 Make sure that the antenna
is connected to the
television (refer to page 1).
Press the ENTER button.
The Auto Store menu is
displayed with Area
selected.
TV
Area : Belgie
Search
Move Enter Return
Auto Store
ASIA W/EUROPE
CIS E/EUROPE
CHINA
HONGKONG U/K
AUSTRALIA
NZ/INDONESIA
SOUTH AFRICA
AMERICA
√√
√√
4 Press the ENTER button again.
5 Press the … or † button to select your area. Press the
ENTER button.
6 To search the channels,
select Search by pressing
the … or † button. Press
the ENTER button.
7 Press the ENTER button
again to start search
channels. To stop the
search, press the ENTER
button.
When the channel
searching has finished, the
Time menu is displayed
with Clock selected.
8 Press the œ or √ button to
move to the hour or minute.
P 1 C-- ----- 102MHz
TV
Search
Start
Enter Return
Search
--:--
--:--
--:--
Time
am
am Off
am Off
7 %
Stop
Enter Return
Clock
Sleep Timer : Off
On Timer
Off Timer
On Timer Volume : 10
Move Enter Return
Set the hour or minute by pressing the … or † button.
continued...
9 When you have finished,
Enjoy your watching
press the MENU button.
The Enjoy your watching is displayed, and then the
channel which has been stored will be activated.
Re-setting the Plug & Play
Method: MENU ➜ …/†
(Setup) ➜ ENTER ➜ …/†
(Plug & Play) ➜ ENTER
TV
Plug & Play
Language : English
Time
Child Lock
Blue Screen : Off
Melody : On
Demonstration
Move Enter Return
Input Source List / Edit Name
◆ Source List
You can switch between
viewing signal from
connected equipment, such
as a VCR, DVD, set-top box,
and the TV source
(broadcast or cable).
You can change the required external source simply
➢
by pressing the VIDEO button on the remote
TV
TV
AV1 ---AV2 ---S-Video ---Component ----
Move Enter Return
control. It might take a short period of time for
pictures to be switched. To return to the TV mode,
press the TV button on the remote control.
◆ Edit Name
You can give a name to the
external source.
TV
AV1 : Belgie
AV2
S-Video
Component
Move Enter Return
Source List
Edit Name
----
VCR
DVD
Cable STB
Sat. STB
AV Recv.
DVD Recv.
Game
Camcorder
DVD Combo
Setup
√√
√√
√√
√√
√√
√√
√√
√√
√√
√√
English - 3
Loading...