Samsung CS-21Z43ZGQ, CS-21Z50Z3Q, CS-21Z47ZGQ, CS-21A551MU, CS-29Z47Z4Q User Manual

...
COLOUR TELEVISION
CS 21Z40/21Z43/21Z45/21Z47/
21Z50/21A550/21A551
Owner’s Instructions

Connection Panel (depending on the model)

The product colour and shape may vary depending on the
model.
Rear Panel
Front (or Side) Panel
Before operating, please read this manual thoroughly,
Register your product at www.samsung.com/global/register.
and retain it for future reference.
Record your Model and Serial number.
▪ Model __________ ▪ Serial No. __________

Control Panel (depending on the model)

The product colour and shape may vary depending on the
model.
Front (or Side) Panel
1 On-screen menu display 2 Volume adjustment 3 Channel selection 4 Remote control sensor 5 Standby indicator 6 Power on/off
You can use the 3 buttons to switch the TV on when it is
in standby mode depending on the model.
The 2 and 3 buttons also have the same function as the
If the remote control no longer works or you have
misplaced it, you can use the controls on the panel of the television.
or
cable television network
Whenever you connect an audio or video system to your
television, ensure that all elements are switched off.
Connecting to an Aerial or Cable Television Network
Connect the aerial or network input cable to the coaxial socket). To view television channels correctly, a signal must be received by the set from one of the sources: an outdoor aerial, cable television network, or satellite network. If you are using an indoor aerial, you may need to adjust it when tuning your television until you obtain a picture that is both sharp and clear.
Connecting to the SCART Input/Output
The SCART VCR, DVD, decoder, satellite receiver, video game device, or video disc player. The SCART output, such as a video game device or video disc player.
2 connectors are used for equipment, such as a
2 is also used for equipment with an RGB
1 (75 Ω
1 Audio input
2 Video input
3 Headphone jack
Connecting to the RCA Input
The
1 (AUDIO-L/R or AUDIO) and 2 (VIDEO) connectors
are used for equipment, such as a camcorder, video disc player, or video game device.
Connecting Headphones
The
3 (headphone) jack is used for watching a television
programme without disturbing the other people in the room. Prolonged use of headphones at a high volume may damage your hearing.
When both the front (or side) AV and rear connectors are
connected to external equipment, the front (or side) AV receives priority.
English - 1
AA68-03992A-01

Remote Control (depending on the model)

2
1
2
1

Switching the Television On and Off

Operation of remote control may be affected by bright
artificial light near to the TV.
4 /
Used to increase or decrease the volume.
5 MENU
Used to display the on-screen menu or return to the previous menu.
6 ▲/▼/◄/►
Used to control the cursor in the menu.
7 S.MENU (option)
Used to display the sound menu.
8 TURBO (option)
Used to select the turbo sound option.
9 DUAL I-II (option)
Used to select the sound mode.
0 SOURCE
Used to display all of the available video sources.
! INFO
Used to view the channel information and setting status you selected.
@ PRE-CH
Used to switch repeatedly between the last two channels displayed.
# P / P
Used to display the next or previous stored channel.
$ EXIT
Used to exit from any display or return to normal viewing.
% MUTE
Used to switch the sound off temporarily. To turn the sound back on, press the
, or
^ ENTER
While using the on-screen menus, press the
ENTER button to activate (or change) a particular item.
& S.MODE (option)
Used to select the sound effect.
* P.MODE
Used to select the picture effect.
( TV
Used to return to the TV mode when it is in external input mode.
) SLEEP
Used to select a preset time interval for automatic turn off.
MUTE, button.
The mains lead is attached to the rear of the television
1 Plug the mains lead into an appropriate socket.
The main voltage is indicated on the rear of the
television and the frequency is 50 or 60Hz.
2 Press the “ I ” button (On/Off) on the front (or side) of the
television.
3 Press the POWER button on the remote control to switch
the television on. The programme that you were watching last is re-selected automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Channel
- Auto Store” on page 3 or “Channel - Manual Store” on page 4.
If the television is initially powered on, several basic
customer settings proceed automatically. Refer to “Setup - Plug & Play” on page 3.
4 To switch the television off, press the “ I ” button (On/Off)
on the front (or side) of the television.

Placing the Television in Standby Mode

The television can be placed in standby mode, in order to reduce power consumption and wear of the cathode ray tube. Standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).
1 Press the POWER button on the remote control while
viewing. The television is in standby mode.
2 To switch the television back on, simply press it again.
You can also switch on by pressing the TV, P / P ,
or numeric
1 POWER
Used to switch the TV on and off.
2 Numeric buttons
Used to select channels directly.
3 -/--
Used to select a channel numbered ten or over. Press this button, then “--” symbol is displayed. Enter the two-digit channel number.
Installing Batteries
Remove the cover. Install two AAA size batteries, then replace the cover. When the remote control does not operate normally, check that the “+” and “–” ends of the batteries are inserted correctly or the batteries are drained.
Do not mix battery types, i.e. alkaline and manganese.
English - 2
Do not leave the television in standby mode for long
periods of time (when you are away on holiday, for example). Turn the television off by pressing the “
button (On/Off) on the front (or side) of the television. It is
best to unplug the set from the mains and aerial.
I
English - 3

Viewing the Menus

1 Press the MENU button.
The main menu is displayed on the screen. Its left side has five icons:
Input, Picture, Sound, Channel, and
Setup.
2 Press the ▲ or ▼ button to select one of the icons.
Press the
ENTER button to access the icon’s sub-menu.
3 Press the ▲ or ▼ button to move to items in the menu.
Press the
ENTER button to enter items in the menu.
4 Press the ▲/▼/◄/► button to change the selected items.
Press the
MENU button to return to the previous menu.
5 Press the EXIT button to exit from the menu.

Setup - Plug & Play (depending on the model)

When the television is initially powered on, several basic customer settings proceed automatically and subsequently. The following settings are available.
1 If the television is in standby
mode, press the button on the remote control. The message
POWER
Start Plug &
Play is displayed.
To start Plug & Play, press the ENTER button. The
Language menu is
displayed.
The Language menu will
automatically appear after several seconds, even if the
ENTER button is not
pressed.
2 Select the appropriated
language by pressing the
▲ or ▼ button. Press the
ENTER button. The
Check antenna input. is
displayed.
If any language is not selected, the language menu
will disappear about 30 seconds later.
Plug & Play
Start Plug & Play.
OK
Enter Exit
Plug & Play
Language
English
Pусcкий
Move Enter Skip
Plug & Play
Check antenna input.
OK
Enter Skip
3 To search the channels,
press the
ENTER button. To stop the search, press the ENTER button. When the channel searching has finished, the
Clock Set
menu is displayed.
4 Press the ◄ or ► button to
move to the hour or minute. Set the hour or minute by
pressing the ▲ or ▼ button.
5 When you have finished,
press the The
MENU button.
Enjoy your watching.
is displayed, and then the channel which has been stored will be activated.
Re-setting the Plug & Play
Method:
MENU ▲/▼ (Setup) ENTER ▲/▼ (Plug & Play) ENTER
Plug & Play
Auto Store
Start
Enter Skip
Plug & Play
Auto Store
P 1 102MHz 7 %
Stop
Enter Skip
Plug & Play
Clock Set 0 0 : 0 0
Move Enter
Adjust Skip
Enjoy your watching.
OK
TV
Plug & Play
Language : English Time Child Lock Blue Screen : Off
Move Enter Return
Setup

Input - Source List

You can switch between viewing signal from connected equipment, such as a VCR, DVD, set-top box,
TV
TV
Ext.
and the TV source (broadcast or cable).
You can change the required
external source simply by pressing the
SOURCE button
Move Enter Return
on the remote control. It might take a short period of time for pictures to be switched. To return to the TV mode, press the
► ► ► ►

Channel - Auto Store

You can scan for the frequency ranges available to you (and availability depends on your country). Automatically allocated programme numbers may not correspond to actual or desired
TV button on the remote control.
programme numbers. However you can sort numbers manually and clear any channels you do not wish to watch.
Channels are sorted and stored in the order which reflects their position in the frequency range
P 1 102MHz 7 %
(with lowest first and highest last). The programme originally
Enter Return
selected is then displayed.
To stop the search before it has finished, press the ENTER
button.
When finished, the
Sort menu is displayed. To sort the stored channels into the desired numerical order, refer to “Channel ­Sort” on page 4. To exit without sorting, press the
EXIT button.
Source List
Search
Stop
continued...
Loading...
+ 5 hidden pages