Samsung CS14F10MJ0XBWT, CS20F10MJ Schematic

COLOR TELEVISION RECEIVER

Chassis : KS1A(P)_Rev.2 Model : CS14F10MJ0XBWT

CS20F10MJ0XBWT CS21F10MJ0XBWT CZ21A083NXXEG

COLOR TELEVISION RECEIVER CONTENTS

Precautions

Specifications and IC Data

Disassembly and Reassembly

Alignment and Adjustment

Troubleshooting

Exploded View and Parts List

Electrical Parts List

Block Diagram

Wiring Diagram

Schematic Diagrams

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

ELECTRONICS

Printed in Korea

AA82-00578A

1. Precautions

1-1 Safety Precautions

1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields.

2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers.

3. Make sure that there are no cabinet openings through which people—particularly children—might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet

ventilation slots, and improperly fitted back

covers.

If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer.

4. Leakage Current Hot Check (Figure 1-1): Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards Institute (ANIS C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7).

5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unit’s AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test.

Fig. 1-1 AC Leakage Test

6. Antenna Cold Check: With the unit’s AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector.

7. X-ray Limits: The picture tube is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original. Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection.

8. High Voltage Limits: High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced.

(X-ray protection circuits also may be called

“horizontal disable” or “hold-down”.)

Heed the high voltage limits. These include the X–ray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic.

Precautions

1-1

LEAKAGE CURRENT

TESTER

DEVICE UNDER

TEST

TEST ALL

EXPOSED METAL

SURFACES

2-WIRE CORD

ALSO TEST WITH

PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)

EARTH

GROUND

(READING SHOULD

NOT BE ABOVE

0.5mA)

Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays.

1-1 Safety Precautions (Continued)

9. High voltage is maintained within specified

limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components.

10. Design Alteration Warning:

Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturer’s warranty.

11. Hot Chassis Warning:

Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC source.

To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert. Re-measure the voltage between the chassis and ground.

12. Some TV chassis are designed to operate with

85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source.

13. Some TV chassis have a secondary ground

system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered.

14. Components, parts and wiring that appear to

have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards.

15. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts.

16. Picture Tube Implosion Warning: The picture tube in this receiver employs “integral implosion” protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original.

17. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some “in-line” picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such “permanently attached” yokes from the picture tube.

18. Product Safety Notice: Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection. These safety features and the protection they give might be lost if the replacement component differs from the original—even if the replacement is rated for higher voltage, wattage, etc.

Components that are critical for safety are indicated in the circuit diagram by shading, ( ) or ( ).

Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.

Precautions

1-2 Samsung Electronics

!

1-2 Servicing Precautions

1. Servicing precautions are printed on the cabinet. Follow them.

2. Always unplug the unit’s AC power cord from the AC power source before attempting to: (a) Remove or reinstall any component or assembly, (b) Disconnect an electrical plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor.

3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position.

4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the portion around the serviced part has not been damaged.

5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks).

6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500V) to the blades of the AC plug.

The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm.

7. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed.

8. Always connect a test instrument’s ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument’s ground lead last.

Precautions

1-3

Warning1: First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between

the servicing and safety precautions, always follow the safety precautions.

Warning2: An electrolytic capacitor installed with the wrong polarity might explode.

1. Some semiconductor (“solid state”) devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity.

2. Immediately before handling any semicon ductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. (Be sure to remove it prior to applying power— this is an electric shock precaution.)

3. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of electrostatic charge.

4. Do not use freon-propelled chemicals. These can generate electrical charges that damage ESDs.

5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs.

6. Use only an anti-static solder removal device. Many solder removal devices are not rated as “anti-static”; these can accumulate sufficient electrical charge to damage ESDs.

7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials.

8. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed.

9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD.

Precautions

1-4 Samsung Electronics

1-3 Precautions for Electrostatically Sensitive Devices (ESDs)

Samsung Electronics 2-1

Specifications and IC Data

2. Specifications and IC Data

2-1 Specifications

Television System:

Channels:

Intermediate Frequencies (MHz) :

MODEL

CI CII CX CK

CW

CS

System

Band

VHF UHF

SYSTEM

IF Carrier Frequency

SYSTEM PAL-I (UHF) PAL-I (VHF/UHF) PAL-B/G, SECAM-B/G PAL-B/G, D/K, SECAM-B/G, D/K PAL-B/G, D/K, SECAM-B/G, D/K, NT 4.43 PAL-B/G, D/K, SECAM-B/G, D/K, NT4.43, NT3.58

PAL/SECAM-

B/G,I

2 - 12

21 - 69

PAL/ SECAM- B/G

PAL, SECAM- D/K

1 - 13

21 - 69

PAL/SECAM-D/K, SECAM-K1

SECAM-K1, PAL-D

2 - 9

13 - 57

PAL - I

NTSC - M

2 - 13 14-69

NTSC - M

Picture Tube:

Power Requirements: Antenna Input Impedance: Speaker Impedance

Picture IF Carrier

Sound IF Carrier

Color Sub Carrier

14 Inch 20 Inch 21 Inch

AC 100~240V, 50/60Hz VHF, UHF : Telescopic dipole antenna (75 ohm unbalanced type )

8 ohm, 5W+5W (Dual Type) 16 ohm, 3W (Monitor Type & Dual Type)

A34KQV42X A48KRD82X(H) A51KQJ63X

38.90

33.40

34.47

Quick start, in-line-gun,

Black stripe, 90

38.90

32.40

34.47

degree deflection

38.90

32.90

34.47

38.90

34.40

35.32

2-2 Samsung Electronics

2-2 IC Line Up

Specifications and IC Data

Loc. No Specification Description Remark

HC101 PAP103 IF PRE-AMP

Table 2-1 IC Line-Up

SPM802ER

IC201S

SPM802ERN

IC301

IC501 TDA6107Q RGB DRIVE AMP

IC601

IC801S

IC802 KA7632

IC902 24C08/KS28C040 EEPROM

PC801S TCET1108 / LTV817B PHOTO COUPLER

IC101 U4468B

LA7840

TDA7266S

KA5Q0765R

TTX, English/Croatian/Romanian/Hungarian/Polish/Czech/ Bulgarian/Russian/Portugal

W/O TTX, English/Croatian/Romanian/Hungarian/Polish/Czech/ Bulgarian/Russian/Portugal

VERTICAL OUTPUT

SOUND-AMP (3W x 1CH or 3W x 2CH or 5W x 2CH)

POWER IC (STR)

CUSTOM REGULATOR (5V, 8V, 3.3V)

SIF - IC

Philips

Sanyo

Philips

TEMIC

2-3 Semiconductor Base Diagrams

Specifications and IC Data

Samsung Electronics 2-3

Fig. 2-1 Semiconductor Base Diagrams

ELECTROLYTICCONDENSER

TRANSISTOR

2SD1651 2SD1650 2SD2499 KSA614

DIODE

KSC815-Y KSA539-Y BC548 KTC9014

IC

SPM-802ERN(Pin 64) SPM-802ER(Pin 64) X24CO8P(Pin 8) KS24C080(Pin 8) U4468B(Pin 16)

IC

UPC574J

or

KA33V

SAW-FILTER

1

G3956M K9260M

B

C

E

IC

E B C

TDA6107Q KA7632

TRANSISTOR

LA7840

KSR1012 KSR1010 KSR2010 KTD863-Y KSC2331-Y

E C B

2-4

MEMO

Samsung Electronics 3-1

Disassembly and reassembly

3. Disassembly and Reassembly

3-1 Back Cover Removal

1. After removing the screws, press the tension rib and pull the cabinet backwards.

2. To reassemble, press the tension rib (see diagram).

3-2 Samsung Electronics

3-2 Main Board Removal

Disassembly and reassembly

1. Separate the socket board from the CRT neck.

2. Remove the Anode Cap from the CRT.

3. Remove the main board by pulling it with both hands.

Warning: The FBT is charged with high voltage. Before removing the Anode Cap, discharge the voltage through one of the heat sinks on the main board.

3-3 Speaker Removal

Disassembly and reassembly

Samsung Electronics 3-3

1. Remove the speaker by pressing the tension rib.

1. Remove the screws.

2. Remove the speaker by pressing the tension rib.

3-4 Samsung Electronics

Disassembly and reassembly

3-4 CRT Removal

1. Spread a soft mat on the floor. Place the TV set face down.

2. Remove the 4 nuts mounting the CRT to the front cabinet. Lift the CRT.

3. Caution: Because of the high vacuum and large surface area of the picture tube, be careful while handling it: (1) Always lift the picture tube by grasping it firmly around the faceplate, (2) Never lift the tube by its neck. (3) Do not scratch the picture tube or apply excessive pressure. Fractures of the glass may cause an implosion.

Alignment and Adjustments

Samsung Electronics 4-1

4. Alignment and Adjustments

4-1 Preadjustment

4-1-1 Factory Mode

1. Do not attempt these adjustments in the Video Mode.

2. The Factory Mode adjustments are necessary when either the EEPROM (IC902) or the CRT is replaced.

3. Do not tamper with the “Adjustment” screen of the Factory Mode menu. This screen is intended only for factory use.

4-1-2 When EEPROM (IC902) Is Replaced

1. When IC902 is replaced all adjustment data revert to initial values. It is necessary to re-program this data.

2. After IC902 is replaced, warm up the TV for 10 seconds.

4-1-3 When CRT Is Replaced

1. Make the following adjustments AFTER setting up after setting up purity and convergence :

White Balance Sub-Brightness Vertical Center Vertical Size Horizontal Size Fail Safe (This adjustment must be the last step).

2. If the EEPROM or CRT is replaced, set PVA to 40 (factory mode) and set SC as follows.

14 inch : 0 20 inch : 9

21 inch : 9

4-2 Factory/Service Mode

4-2-1 Procedure for the “Adjustment” Mode

1. This mode uses the standard remote control. The Service Mode is activated by entering the following remote-control sequence :

(1) DISPLAY→FACTORY. (2) STAND-BY→ DISPLAY→ MENU→ MUTE

→POWER ON.

2. The “SERVICE (FACTORY)” message will be displayed. The Service Mode has four components: ADJUST, OPTION and Reset.

3. Access the Adjustment Mode by pressing the “VOLUME” keys ( Up or Down). The adjustment parameters are listed in the accompanying table, and selected by pressing the CHANNEL keys (▲ ,▼).

4. Selection sequences for the all system:

DOWN or UP key: SCT>SBT>BLR>BLB>RG>GG>BG>VSL> VS>VA>HS>SC>SDL>STT>SSP>PDL> NDL>PSR>NSR>AGC>VOL>LCO>TXP

5. The VOLUME keys increase or decrease the adjustment values (stored in the non-volatile memory) when Adjustment Mode is cancelled.

6. Cancel the Adjustment Mode by re-pressing the “FACTORY” or “Power OFF” keys.

4-2-2 Main Adjustment Parameter

NOTE : PVS,PVA, PHS, parameters must be aligned using the 50Hz vertical-field rates.

Alignment and Adjustments

4-2 Samsung Electronics

OSD FUNCTION RANGE INITIAL DATA REMARK SCT Sub Co ntra s t 0~23 SBT Sub Bri g ht ne ss 0~23 BLR Bl ac k Le v el offse t Blue 0~15 BLB Bl ac k Le v el offse t Red 0~15

RG R e d Ga i n 0~63 GG Green Gai n 0~63 BG Bl u e Gai n 0~63

VSL Ve rt ic al S lop e 0~63

VS Vert i ca l Shi f t 0~63 VA Ver t ical Am pli tude 0~63 HS Hori zontal Shif t 0~63

SC S- Cor re c t io n 0~63 CDL Cat hode Drive Level 0~15 STT Sub Tint 0~7 SSP Sub Sharpness 0~7 PD L PAL Del ay 0~15

13

9 9 7

32

25(Fix)

31 19 38

40(Fix)

30

9 9 3 0

15(Fix) NDL NTSC Delay 0~15 PSR PAL Sub col oR 0~23 NSR NTSC Sub col oR 0~23 AGC Automat ic Gai n Cont rol 0~63 VOL Volume pre s et t i ng 0~63 LCO SECAM-L Vision I F 0~1 TXP TTX Pos ition 0~15

10

2

5 23 10

0

9

Alignment and Adjustments

Samsung Electronics 4-3

4-2-3 Option Bytes

In the Service Mode, various can be selected via the Option Table. Example:

Option Table : xx xx xx xx

1

2

3

4

5

6

7

8

9

10

LNA

SYSTEM

AUDIO

JACK

ZOOM

AUTO POWER

SBL

2nd SIF

HOTEL MODE

BKS

ON

CZ

MONO

RCA

NOR/ZOOM/16:9

ON

OFF

ON

OFF

ON

Alignment and Adjustments

4-4 Samsung Electronics

4-3 Other Adjustments

4-3-1 General

1. Usually, a color TV needs only slight touchup adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync and focus.

2. The picture should have good black and white details. There should be no objectionable color shading; if color shading is present, perform the purity and convergence adjustments described below.

3. Use the specified test equipment or its equivalent.

4. Correct impedance matching is essential.

5. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV. When inserting signal markers, do not allow the marker generator to distort test results.

6. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate.

7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts.

8. To protect against shock hazard, use an isolation transformer.

4-3-2 Automatic Degaussing

A degaussing coil is mounted around the picture tube, so that external degaussing after moving the TV should be unnecessary. But the receiver must be properly degaussed upon installation.

The degaussing coil operates for about 1 second after the power is switched ON. If the set has been moved or turned in a different direction, disconnect its AC power for at least 30 minutes.

If the chassis or parts of the cabinet become magnetized, poor color purity will result. If this happens, use an external degaussing coil. Slowly move the degaussing coil around the faceplate of the picture tube and the sides and front of the receiver. Slowly withdraw the coil to a distance of about 6 feet before removing power.

4-2-4 RESET

The Reset Mode is used during factory inspection. Function Reset:

1. Picture Custom

2. Auto Volume Off

3. Color System Auto (option)

4. Sound System D/K (option)

5. Blue Screen Off

6. Low Noise AMP Off (option)

7. Volume 10

8. CH. Skip Erased

9. CH. Lock Off

10. Timer Off

Alignment and Adjustments

Samsung Electronics 4-5

4-3-3 High Voltage Check

CAUTION: There is no high voltage adjustment on this chassis. The B+ power supply must be set to +125 volts (Full color bar input and normal picture level).

1. Connect a digital voltmeter to the second

anode of the picture tube.

2. Turn on the TV. Set the Brightness and

Contrast controls to minimum (zero beam current).

3. The high voltage should not exceed 27.5KV.

4. Adjust the Brightness and contrast controls to

both extremes. Ensure that the high voltage does not exceed 27.5KV under any conditions.

4-3-4 FOCUS Adjustment

1. Input a black and white signal.

2. Adjust the tuning control for the clearest pic-

ture.

3. Adjust the FOCUS control for well defined

scanning lines in the center area of the screen.

4-3-5 Cathode Voltage Adjustment

(Screen Adjustment)

1. Connect CRT socket pin GK to an oscilloscope

probe.

2. Input a gray scale pattern. (Use a pattern gen-

erator, PM5518)

3. Use the P mode key (on the remote control)

for the STANDARD picture.

4. Adjust the Screen VR (on the FBT) so that the

voltage on the oscilloscope becomes 120+2.5V (See Fig. 4-1).

4-3-6 Purity Adjustment

1. Warm up the receiver for at least 20 minutes.

2. Plug in the CRT deflection yoke and tighten the clamp screw.

3. Plug the convergence yoke into the CRT and set in as shown in Fig. 4-2.

4. Input a black and white signal.

5. Fully demagnetize the receiver by applying an external degaussing coil.

6. Turn the CONTRAST and BRIGHTNESS controls to maximum.

7. Loosen the clamp screw holding the yoke. Slide the yoke backward or forward to provide vertical green belt. (Fig. 4-3).

8. Tighten the convergence yoke.

9. Slowly move the deflection yoke forward, and adjust for the best overall green screen.

10. Temporarily tighten the deflection yoke.

11. Produce blue and red rasters by adjusting the low-light controls. Check for good purity in each field.

12. Tighten the deflection yoke.

Fig. 4-1

_

+

120 2.5V

GND

14" :120 2.5V 20, 21" : 120 2.5V

_

+ _

+

Alignment and Adjustments

4-6 Samsung Electronics

4-3-7 White Balance Adjustment

Fig. 4-2 Convergence Magnet Assembly

Fig. 4-3 Center Convergence Adjustment

Fig. 4-4

(a) Set up

1. Warm up the TV for at least 30 minutes in the Aging Mode (OSD White). This mode is displayed by entering the following sequence:

DISPLAY

→FACTORY →FACTORY

2. Input a Toshiba pattern.

(b) Low-Light Adjustment

1. Set SBT to 3.5 ± 0.5 fL in the Factory Service Mode with using CA100. See Fig. 4-4

➁.

2. Adjust RG,BG so that the levels are suitable to each local area.

(c) High-Light Adjustment

1. Set SCT to 55 FL (20”. 21”), 65 FL(14”) in the Factory Service Mode with using CA100. See Fig. 4-4

①.

6 Pole Magnet

Clamper

Screw

4 Pole Magnet

2 Pole Magnet

2 POLE PURITY

Vertical Green Belt

YOKE CLAMP SCREW

6 POLE

CONVERGENCE 4 POLE CONVERGENCE

ADJUST THE ANGLE (VERTICAL LINES)

31m/m

1

2

Alignment and Adjustments

Samsung Electronics 4-7

4-3-8 Center Convergence Adjustment

1. Warm up the receiver for at least 20 minutes.

2. Adjust the two tabs of the 4 pole magnets to change the angle between them. Superimpose the red and blue vertical lines in the center area of the screen.

3. Adjust the Brightness and Contrast controls for a well defined picture.

4. Adjust the two-tab pairs of the 4 pole magnets, and change the angle between them. Superimpose the red and the blue vertical lines in the center area of the screen.

5. Turn the both tabs at the same time, keeping the angle constant, and superimpose the red and blue horizontal line in the center of the screen.

6. Adjust the two-tab pairs of the 6-pole magnets to superimpose the red and blue line onto the green. (Changing the angle affects the vertical lines, and rotating both magnets affects the horizontal lines.)

7. Repeat adjustments 2~6, if necessary.

8. Since the 4-pole magnets and 6-pole magnets

interact, the dot movement is complex (Fig. 4-5).

Fig. 4-5 Center Convergence Adjustment

BLUE

RED

RED/BLUE

GREEN

4-Pole Magnet Movement

6-Pole Magnet Movement

4-3-9 RF AGC Adjustment

Set the AGC data to 23 (Factory Mode).

4-3-10 Sub-Color Adjustment

Set data to (Factory Mode).

4-3-11 Geometry Adjustment

SC →VS→VSL→HS

1. Input a lion head pattern (in the PAL channel).

2. Set the SC (S-Correction) as follows : 9 (21”), 9 (20”), 0 (14”) and VA 40 so that the lion head circle becomes oval.

3. Adjust with VSL (Vertical-Slope) so that the bottom margin of the picture is 4.

Fig. 4-7

4. Adjust with VS (Vertical shift) so that the top margin of the picture is 4.

Fig. 4-8

5. Adjust with HS (Horizontal Shift) so that the lion-head pattern and CRT centers are aligned.

Fig. 4-9

6. Adjust HS (using the width coil) so that the left and right margins of the picture are 5.

Alignment and Adjustments

4-8 Samsung Electronics

4

5

4

PSR NSR

2 5

Samsung Electronics

Troubleshooting

5-1

5. Troubleshooting

5-1 No Video (Raster On, No Sound)

Open the IF Pin of Tuner

Measure the

Voltage of Each Pin

of TU01S

Yes

Check IC201S

Pins 2,3

Yes

Check IC201S Pins 40,49,50

No

Check/Replace

TU01S

Check/Replace

IC201S

See "No Sound"

(Video OK)

Check/Replace

IC501, IC201S

See "No Video"

(Sound OK)

See "No Sound"

(Video OK)

5-2 Samsung Electronics

5-2 No Power

Troubleshooting

Check the 125V,

13.0V B+ Lines

Yes

Check IC802

Pin 8 (8V)

Pin 9 (9V)

Pin 10 (5V)

Check IC201S

Pin 1 (3.3V)

Yes

Check IC201S

Pin 1 : Stand-by : 0V

Normal : 3.3V

No

Check/Replace

IC801S, D801S, D802S,

D803S,D804S,FP801S

Check/Replace

IC802 (KA7632)

Check/Replace

IC201S

Check/Replace

IC201S, (µ-com).

Check IC201S,

Pin 33 (H-out)

No

Check/Replace

IC201S, Q401, Q402.

5-3 No Video (Sound OK)

Troubleshooting

Samsung Electronics 5-3

Check IC201S Pin 40 (CVBS)

Yes

Check IC201S

Pins 38/R214, R215

Check IC201S

Pin 49 (V-GUARD)

Pin 50 (Cut-off)

Pin 51~53 (R,G,B-out)

Yes

Check IC501

on the CRT PCB

No

Check/Replace

IC201S

Check/Replace

IC201S

Check/Replace

IC501

Check/Replace

R421, R505 (HEATER 6.3Vrms)

D503 (CRT G1 pin)

CRT, V999S

5-4 Samsung Electronics

Troubleshooting

5-4 No Sound (Video OK)

5-5 No TTX

Check IC201S

Pin 44 (Sound Out)

Yes

Check IC601

Pins 6 (0V)

No

Check IC601

Pin 3,13 (B+ 10-12.5V)

Yes

Check IC601

No

Yes

No

Check/Replace

IC201S

Check/Replace

Q904, IC201S

Check/Replace

R814, R815

Check/Replace

IC601

Check/Replace

A/V Front assembly.

Check IC201S

Yes

See No Video

Yes

No

Check/Replace

IC201S

6. Exploded View & Parts List

6-1 CS14F10MJ0XBWT

Exploded View & Parts List

Samsung Electronics 6-1

1-1 AA64-03514A CABINET FRONT;14F10,(TTSEC),HIPS,HB,G430 1 CIS3 S.N.A 1-2 AA64-70127F BADGE-BRAND;NEW,AL,T1.4,6.3,L40,R800,SIL 1 T0057 S.N.A 1-3 AA64-03523A KNOB POWER;F10,ABS,HB,G3676,SVM3012 1 T0023 S.N.A 1-4 AA61-60003J SPRING ETC-CS;-,SUS304,-,-,OD6,N7,OD6,-, 1 CIS7 S.N.A 1-5 AA65-30105A CLAMPER CORE-WIRE;ALL MODEL,NYLON 66,V2, 1 S.N.A 1-6 AA64-03524A WINDOW REMOCON-LED;F10,PC,CLEAR 1 S.N.A 1-7 6003-001019 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR 1 T0081 1-8 AA64-03522A KNOB CONTROL;F10,ABS,HB,G3676,SVM3012 1 T0022 S.N.A 1-9 6003-001019 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR 1 T0081 1-10 AA96-00652A ASSY SPEAKER;-,16OHM,3W,3001-001211,200M 1 S.N.A 1-11 6003-001023 SCREW-TAPTITE;RWH,+,B,M3,L10,ZPC(YEL),SW 4 T0081 S.N.A 1-12 AA61-40113A STOPPER-PCB;501H,HIPS,-,-,HB,NTR,- 1 S.N.A 1-13 AA61-40010A BOSS-WING;-,HIPS,-,-,-,NTR,HB 2 S.N.A 1-14 AA61-00721C HOLDER-RAIL;H4,HIPS,V0,GRAY 1 S.N.A 2 AA95-03195A ASSY SUB PCB-A/V SIDE;KS1A(MAC),PAL,MONO 1 T0091 2-1 AA96-01630A ASSY COVER P-HOLDER AV;14F10,HIPS HB,G43 1 S.N.A 3 AA03-10002M CRT COLOR;A34KQV42X,0mG,3.20mH,30.0mH,4. 1 T0063 4 AA63-60028A SPACER-DY;-,NEOPRENE,-,-,-,BLK,-,-,V0 W1 4 S.N.A 5 AA60-10050R SCREW-ASSY;-,SWRCH18A,M5,L31.5,HH,+,WC,- 4 SC016 S.N.A 6 AA64-03516A CABINET BACK;14F10,HIPS,FV2,GR503 1 T0015 7 AA96-20109B ASSY POWER CORD;-,CP2/NO(4.0),H/C250,KKP 1 T0066 S.N.A 8 AA94-13004A ASSY PCB MAIN;CS14F10MJ0XBWT,KS1A 1 T0073

No Code No Description Specification Q’ty Remark S.N.A

You can search for the updated part code through ITSELF web site. URL : http://itself.sec.samsung.co.kr

Exploded View & Parts List

6-2 Samsung Electronics

6-2 CS20F10MJ0XBWT

1 AA64-03518A CABINET FRONT;20F10,(TTSEC),HIPS,HB,G430 1 CIS3 S.N.A 1-2 AA64-70123B BADGE-BRAND;ALL,AL,8.5,L50,BLK,SILVER,SA 1 T0057 S.N.A 1-3 AA64-03523A KNOB POWER;F10,ABS,HB,G3676,SVM3012 1 T0023 S.N.A 1-4 AA61-60003J SPRING ETC-CS;-,SUS304,-,-,OD6,N7,OD6,-, 1 CIS7 S.N.A 1-5 AA65-30105A CLAMPER CORE-WIRE;ALL MODEL,NYLON 66,V2, 2 S.N.A 1-6 AA64-03524A WINDOW REMOCON-LED;F10,PC,CLEAR 1 S.N.A 1-7 6003-001019 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR 1 T0081 1-8 AA64-03522A KNOB CONTROL;F10,ABS,HB,G3676,SVM3012 1 T0022 S.N.A 1-9 6003-001019 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR 1 T0081 1-10 AA96-01188A ASSY SPEAKER P;16OHM,3001-001008,AA39-20 1 CIS5 1-11 6003-001019 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR 4 T0081 1-12 AA61-40113A STOPPER-PCB;501H,HIPS,-,-,HB,NTR,- 1 S.N.A 1-13 AA61-00721C HOLDER-RAIL;H4,HIPS,V0,GRAY 1 S.N.A 2 AA95-03196A ASSY SUB PCB-A/V SIDE;KS1A(MAC),MONO,20F 1 T0091 2-1 AA96-01632A ASSY COVER P-HOLDER AV;21F10,HIPS HB,G43 1 S.N.A 3 AA03-10029W CRT COLOR;A48KRD82X(H),+380mG,2.20mH,30. 1 T0063 4 AA65-30107A CLAMPER CORE-D,COIL;20~22 INCH,NYLON 66, 4 S.N.A 4 AA63-60028A SPACER-DY;-,NEOPRENE,-,-,-,BLK,-,-,V0 W1 4 S.N.A 5 AA60-10050R SCREW-ASSY;-,SWRCH18A,M5,L31.5,HH,+,WC,- 4 SC016 S.N.A 6 AA64-03006A CABINET-BACK;21F3,HIPS,FV2,GR503 1 T0015 6-1 AA60-10050T SCREW-TAPPING;-,SWRCH18A,M4,L20,RH,+,2S, 4 T0081 S.N.A 7 AA96-20109B ASSY POWER CORD;-,CP2/NO(4.0),H/C250,KKP 1 T0066 S.N.A 8 AA94-13238R ASSY PCB MAIN;MAC,KS1A 1 T0073

No Code No Description Specification Q’ty Remark S.N.A

You can search for the updated part code through ITSELF web site. URL : http://itself.sec.samsung.co.kr

Exploded View & Parts List

Samsung Electronics 6-3

6-3 CS21F10MJ0XBWT

1-1 AA64-03521A CABINET FRONT;21F10,HIPS,HB,G4309,SV012P 1 CIS3 S.N.A 1-2 AA64-70123B BADGE-BRAND;ALL,AL,8.5,L50,BLK,SILVER,SA 1 T0057 S.N.A 1-3 AA64-03523A KNOB POWER;F10,ABS,HB,G3676,SVM3012 1 T0023 S.N.A 1-4 AA61-60003J SPRING ETC-CS;-,SUS304,-,-,OD6,N7,OD6,-, 1 CIS7 S.N.A 1-5 AA65-30105A CLAMPER CORE-WIRE;ALL MODEL,NYLON 66,V2, 2 S.N.A 1-6 AA64-03524A WINDOW REMOCON-LED;F10,PC,CLEAR 1 S.N.A 1-7 6003-001019 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR 4 T0081 1-8 AA64-03522A KNOB CONTROL;F10,ABS,HB,G3676,SVM3012 1 T0022 S.N.A 1-9 6003-001019 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR 1 T0081 1-10 AA96-01188A ASSY SPEAKER P;16OHM,3001-001008,AA39-20 1 CIS5 1-11 6003-001019 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR 4 T0081 1-12 AA61-40113A STOPPER-PCB;501H,HIPS,-,-,HB,NTR,- 1 S.N.A 1-13 AA61-00721C HOLDER-RAIL;H4,HIPS,V0,GRAY 1 S.N.A 2 AA95-03196A ASSY SUB PCB-A/V SIDE;KS1A(MAC),MONO,20F 1 T0091 2-1 AA96-01632A ASSY COVER P-HOLDER AV;21F10,HIPS HB,G43 1 S.N.A 3 AA03-10024T CRT COLOR;A51KQJ63X(H),+380mG,2.28mH,22. 1 T0063 4 AA65-30107A CLAMPER CORE-D,COIL;20~22 INCH,NYLON 66, 4 S.N.A 5 AA60-10050R SCREW-ASSY;-,SWRCH18A,M5,L31.5,HH,+,WC,- 4 SC016 S.N.A 6 AA64-03006A CABINET-BACK;21F3,HIPS,FV2,GR503 1 T0015 6-1 AA60-10050T SCREW-TAPPING;-,SWRCH18A,M4,L20,RH,+,2S, 4 T0081 S.N.A 7 AA96-20109B ASSY POWER CORD;-,CP2/NO(4.0),H/C250,KKP 1 T0066 S.N.A 8 AA94-13238S ASSY PCB MAIN;MAC,KS1A 1 T0073

No Code No Description Specification Q’ty Remark S.N.A

You can search for the updated part code through ITSELF web site. URL : http://itself.sec.samsung.co.kr

Exploded View & Parts List

6-4 Samsung Electronics

6-4 CZ21A083NXXEG

1 AA96-01636A ASSY C.P-FRONT;21A08,HIPS HB,KS1A,SV 1 CIS 1* AA64-03672A CABINET FRONT;21A08,HIPS,HB,SV012P,SEH,K 1 CIS3 1-1 AA64-70010B BADGE-BRAND;-,AL,-,-,L50,-,SILVER,SS R20 1 T0057 S.N.A 1-2 AA64-00814N KNOB POWER;21A8,HIPS,HB,SV-012P-II,KS1A 1 T0023 S.N.A 1-3 AA61-60003J SPRING ETC-CS;-,SUS304,-,-,OD6,N7,OD6,-, 1 CIS7 S.N.A 1-4 6006-001095 SCREW-ASS’Y TAPT;WP,BH,+,M4,L12,ZPC(YEL) 2 AV+CF S.N.A 1-5 AA95-01709A ASSY ETC-PCB,A/V SIDE;,21D8,KS1A,STEREO 1 CIS 1-6 STOPPER-PCB 1 S.N.A 1-7 AA65-30105A CLAMPER CORE-WIRE;ALL MODEL,NYLON 66,V2, 1 S.N.A 1-8 HA64-00818B INDICATOR LED;21A7,-,ACRYL,-,CLR,- 1 T0059 1-9 HA64-00816B WINDOW REMOCON;-,21A8,-,PC,V0,VIOLET,- 1 CIS S.N.A 1-10 6003-001026 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR 1 CB+JCK S.N.A 1-11 AA64-00812J KNOB CONTROL;21A8,HIPS,HB,SV-012P,GRY 1 T0022 S.N.A 1-12 6003-001026 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR 1 CF+KN S.N.A 1-13 3001-000274 SPEAKER;5W,8OHM,90DB,160HZ 2 T0082 1-14 6003-001019 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR 8 T0081

2 AA03-00214A CRT COLOR;A51QDX992X011,+380MG,1.85MH,18 1 T0063 2-1 AA65-30107A CLAMPER CORE-D,COIL;20~22 INCH,NYLON 66, 4 S.N.A 2-2 AA60-10050Q SCREW-ASSY;-,SWRCH18A,M5,L26.5,HH,+,WC,- 4 SC016 S.N.A 2-3 3704-001105 SOCKET-CRT;11P,20PI,26.5PI,NI,- 1 V999S

3 AA64-02358C CABINET BACK;21A8,KS1A 1 T0015 3-1 6002-000515 SCREW-TAPPING;RH,+,2,M4,L15,ZPC(WHT),SWR 4 T0081 3-2 AA96-01126A ASSY POWER CORD;DP,AA39-10001G,CP2,H/C25 1 T0066

No Code No Description Specification Q’ty Remark S.N.A

You can search for the updated part code through ITSELF web site. URL : http://itself.sec.samsung.co.kr

Electrical Parts List

Samsung Electronics 7-1

ASSY COVER FRONT

1 M0001 AA90-04708A ASSY COVER FRONT ;CS14F10MJ0XBWT S.N.A ..2 T0081 6003-001019 SCREW-T APTITE;RH,+,B,M4,L12,ZPC(BLK),SWR

..2 SC016 AA60-10050R SCREW-ASSY;-,SWRCH18A,M5,L31.5,HH,+,WC,- S.N.A ..2 T0081 AA60-10050T SCREW-TAPPING;-,SWRCH18A,M4,L20,RH,+,2S, S.N.A ..2 AA65-30106A CLAMPER CORE-D,COIL;14 INCH,NYLON 66,V2, S.N.A ..2 T0003 AA96-01627A ASSY COVER P-FRONT;14F10,TTSEC,HIPS HB,G ...3 T0081 6003-001019 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR ...3 T0081 6003-001019 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR ...3 T0081 6003-001023 SCREW-TAPTITE;RWH,+,B,M3,L10,ZPC(YEL),SW S.N.A ...3 AA61-40113A STOPPER-PCB;501H,HIPS,-,-,HB,NTR,- S.N.A ...3 CIS7 AA61-60003J SPRING ETC-CS;-,SUS304,-,-,OD6,N7,OD6,-, S.N.A ...3 CIS3 AA64-03514A CABINET FRONT;14F10,(TTSEC),HIPS,HB,G430 S.N.A

....4 AA61-40010A BOSS-WING;-,HIPS,-,-,-,NTR,HB S.N.A

...3 T0022 AA64-03522A KNOB CONTROL;F10,ABS,HB,G3676,SVM3012 S.N.A ...3 T0023 AA64-03523A KNOB POWER;F10,ABS,HB,G3676,SVM3012 S.N.A ...3 AA64-03524A WINDOW REMOCON-LED;F10,PC,CLEAR S.N.A ...3 T0057 AA64-70127F BADGE-BRAND;NEW,AL,T1.4,6.3,L40,R800,SIL S.N.A ...3 AA65-30105A CLAMPER CORE-WIRE;ALL MODEL,NYLON 66,V2, S.N.A ...3 AA96-00652A ASSY SPEAKER;-,16OHM,3W,3001-001211,200M S.N.A

....4 T0082 3001-001211 SPEAKER;3W,16OHM,86DB,240HZ

....4 T0076 AA39-20501A LEAD CONNECTOR-ASSY;,3(2),200,67096-003,

...3 AA61-00721C HOLDER-RAIL;H4,HIPS,V0,GRAY S.N.A

ASSY COVER REAR

1 M0002 AA90-04711A ASSY COVER REAR;14F10,HIPS,FV2,GR503,KS1 S.N.A ..2 T0015 AA64-03516A CABINET BACK;14F10,HIPS,FV2,GR503

..2 AA65-30008A CLAMPER CORE-CORD;-,PE,HB,-,BLK,- S.N.A

ASSY CPT

1 AA91-06409A ASSY CPT;AA03-10002M,A34KQV42X,0MG,SDI, S.N.A ..2 AA91-02164T ASSY CPT;A34KQV42X,14,+380MG,BARE S.N.A

...3 T0063 AA03-10002M CRT COLOR;A34KQV42X,0mG,3.20mH,30.0mH,4. ...3 T0079 AA27-00001A MAGNET CONVERGENCE;-,JH225-06A,22.5MM ...3 T0078 AA27-00041A DEFLECTION YOKE;-,QPC-E3704,14INCH,-,3.1 ...3 AA63-60028A SPACER-DY;-,NEOPRENE,-,-,-,BLK,-,-,V0 W1 S.N.A ..2 AA98-70014A ASSY TBC WIRE(P);-,14,NTSC,PAL,1P,TVI S.N.A ..2 T0089 AA27-00241A COIL DEGAUSSING;-,CPT TV 14INCH,-,10%,55

ASSY CHASSIS

1 M0017 AA91-06456A ASSY CHASSIS;CS14F10MJ0XBWT,KS1A S.N.A ..2 T0073 AA94-13004A ASSY PCB MAIN;CS14F10MJ0XBWT,KS1A

...3 0202-000187 SOLDER-WIRE FLUX;-,RS60S,D1.2,63Sn/37Pb S.N.A ...3 T0090 0502-001160 TR-POWER;2SD2499,NPN,50000mW,TO-3P,BK,8...3 IC112 1103-001106 IC-EEPROM;C81DC,1028x8Bit,DIP,8P,300MIL, ...3 NT802S 1404-001045 THERMISTOR-NTC;4.7ohm,15%,2900K,35.0mW ,T ...3 P803T 1404-001265 THERMISTOR-PTC;4.5OHM/100OHM,+30/-20%,22 ...3 C598 2201-000446 C-CERAMIC,DISC;3.3NF,20%,400V,Y5U,TP,15X ...3 CR410S 2303-001015 C-FILM,PPF;5.5nF,5%,1.6kV,TP,29x9.5x17,2 ...3 CR402S 2306-000195 C-FILM,MPPF;360nF,5%,400V,TP,26x19x11.5,

...3 CX801S 2306-000318 C-FILM,MPPF;220nF,20%,250V,TP,-,22.5mm ...3 C701 2401-002213 C-AL;150uF,+30-10%,450V,GP,BK,25x35 ...3 SF101S 2904-001063 FILTER-SAW AV;38.9MHz,SIP5K,TP,18.5dB,B/ ...3 SW801S 3403-001134 SWITCH-PUSH;250V,5A,DPST,ON-OFF ,...3 FP801S 3601-000281 FUSE-CARTRIDGE;250V,4A,TIME-LAG,GLASS,5. ...3 V999S 3704-001089 SOCKET-CRT;7P,22.5PI,12PI,SN,...3 CN906 3711-002648 CONNECTOR-HEADER;BOX,9P,1R,2.5mm,STRAIGH ...3 JS701 3722-000497 JACK-PIN;4P,3.4mm,SN,BLK,...3 T0119 AA09-00354A IC MICOM;TDA9381/N2/3I,SPM-802EEN4,64P,3 ...3 T801S AA26-00134A TRANS SWITCHING;,CS21S5T,160V~260V,PM2 P ...3 T444S AA26-00201A TRANS FBT;FCA173B,KS1A-1,3.8mH,FERRITE,1 ...3 T401 AA26-50001B TRANS-HORIZ.DRIVE;-,-,-,7.1mH,-,-,102uH, ...3 LR401S AA27-00053A COIL LINEARITY;-,193uH,DR10X10 C:4.35,7. ...3 LX801S AA29-30001B FILTER LINE NOISE;-,-,-,-,27MH,-,-,-,ST, ...3 RM901 AA32-00015A MODULE REMOCON;FRP-3521H31,38KHZ,940MM,M ...3 T0076 AA39-20620C LEAD CONNECTOR-ASSY;,9P,500MM,YBNH250-09 ...3 TU01S AA40-00067A TUNER;TAEL-G671D,-,PAL,181CH,38.9MHz,-,7 ...3 GT301 AA60-40012D PIN-GT,ASSY;T1.6,6-12.5-,NYLON66 S.N.A ...3 IC801S AA96-00242D ASSY H/S;SCREWAA62-30186B,5Q0765RTH,OIL S.N.A

....4 CIS 0205-001027 OIL-SILICON;G746,-,- S.N.A

....4 T0086 1203-002916 IC-PWM CONTROLLER;KA5Q0765RTH-YDTU,TO-22

....4 T0081 6003-000333 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW S.N.A

....4 CIS AA62-30186B HEAT SINK-ES;-,-,-,SILVER,171J + COVER-H S.N.A

....4 CIS AA63-30189A COVER-HEATSINK;-,PC-ABS,T0.8,-,-,V0,NTR, S.N.A

...3 IC301 AA96-00244M ASSY H/S;SCREWAA64-00046A,LA78040N,OIL S S.N.A

....4 CIS 0205-001027 OIL-SILICON;G746,-,- S.N.A

....4 T0088 1204-002121 IC-VERTICAL DEF.;LA78040N,TO220,7P,-,PLA

....4 T0081 6003-000335 SCREW-TAPTITE;RH,+,2S,M3,L8,ZPC(YEL),SWR S.N.A

....4 CIS AA62-00046A HEAT SINK-PS;-,-,T1.0,-,D1(DREAM) 60X25X S.N.A

...3 IC802 AA96-00245A ASSY H/S;-,-,AA62-00055A,KA7632,- S.N.A

....4 T0087 1203-001939 IC-POSI.FIXED REG.;7632,SIP,10P,-,PLASTI

....4 T0081 6003-000334 SCREW-TAPTITE;RH,+,2S,M3,L6,ZPC(YEL),SWR

....4 AA62-00055A HEAT SINK-PS;-,-,T1.0,-,35*15*25,D1,-,-, S.N.A

...3 LD901 AA96-00555A ASSY LED GUIDE;-,-,UEX-LD-030,GREEN S.N.A ...3 IC501 AA96-50311A ASSY H/S;-,VIDEO,AA62-30175D,TDA6107Q,- S.N.A

....4 T0074 1201-001159 IC-VIDEO AMP;6107,ZSIP,9P,-,SINGLE,-,PLA

....4 T0081 6003-000334 SCREW-TAPTITE;RH,+,2S,M3,L6,ZPC(YEL),SWR

....4 AA62-30175D HEAT SINK-PS;-,SECC,T1.0,-,33X15X30 FT-2 S.N.A

...3 IC602 AA96-50311K ASSY H/S;-,AMP,AA62-30175D,TDA8943SF S.N.A

....4 T0085 1201-001740 IC-AUDIO AMP;TDA8943,SIL,9P,850MIL,SINGL

....4 T0081 6003-000334 SCREW-TAPTITE;RH,+,2S,M3,L6,ZPC(YEL),SWR

....4 AA62-30175D HEAT SINK-PS;-,SECC,T1.0,-,33X15X30 FT-2 S.N.A

...3 AA97-14085A ASSY AUTO-MAIN;CS14F10MJ0XBWT,KS1A S.N.A

....4 D901 0401-000005 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,

....4 D811 0401-000005 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,

....4 D201 0401-000005 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,

....4 D804 0401-000006 DIODE-SWITCHING;BAV21,250V,250mA,DO-35,T

....4 T0083 0402-000254 DIODE-RECTIFIER;RGP10J,600V ,1A,DO-41,TP

....4 T0083 0402-000493 DIODE-RECTIFIER;1R5GU41,400V ,1.5A,DO-15L

....4 T0083 0402-000546 DIODE-RECTIFIER;TVR10G,400V ,1.0A,DO-41,T

....4 T0083 0402-001111 DIODE-RECTIFIER;1N5397GP,600V,1.5A,DO-20

....4 T0083 0402-001321 DIODE-RECTIFIER;1A4G,400,1A,R-1,TP

7-1 CS14F10MJ0XBWT

Level Loc. No. Code No. Description ; Specification Remark Level Loc. No. Code No. Description ; Specification Remark

7. Electrical Parts List

You can search for the updated part code through ITSELF web site. URL : http://itself.sec.samsung.co.kr

....4 T0083 0402-001352 DIODE-RECTIFIER;GUF15G-20A,400V ,1.5A,DO-

....4 T0083 0402-001443 DIODE-RECTIFIER;EGP20K,800V ,2A,DO-15,TP

....4 DZ016 0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V ,5.45-5.73V,500

....4 DZ016 0403-000700 DIODE-ZENER;TZP33A,33V ,31-35V,1W,DO-41,T

....4 DZ016 0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V ,8.57-9.01V,500

....4 DZ016 0403-001140 DIODE-ZENER;RD10ESAB-T4,10V ,9.19-10.30V,

....4 DZ016 0403-001221 DIODE-ZENER;UZ39BSB,35.36-37.19V ,500MW,D

....4 DZ016 0403-001317 DIODE-ZENER;MTZJ3.0B,3.01-3.22V ,500mW,DO

....4 DZ016 0403-001318 DIODE-ZENER;MTZJ4.3B,4.17-4.43V ,500mW,DO

....4 DZ016 0403-001319 DIODE-ZENER;MTZJ4.7C,4.68-4.93V ,500mW,DO

....4 DZ016 0403-001322 DIODE-ZENER;MTZJ8.2B,7.78-8.19V ,500mW,DO

....4 DZ016 0403-001327 DIODE-ZENER;MTZJ18A,16.22-17.06V ,500mW,D

....4 DZ016 0403-001328 DIODE-ZENER;MTZJ22A,20.15-21.20V ,500mW,D

....4 Q901 0501-000283 TR-SMALL SIGNAL;KSA539,PNP,400mW,TO-92,T

....4 Q206 0501-000283 TR-SMALL SIGNAL;KSA539,PNP,400mW,TO-92,T

....4 Q201 0501-000283 TR-SMALL SIGNAL;KSA539,PNP,400mW,TO-92,T

....4 Q402 0501-000369 TR-SMALL SIGNAL;KSC2331-Y,NPN,1000mW,TO-

....4 Q702 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW ,TO-92,T

....4 Q903 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW ,TO-92,T

....4 Q905 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW ,TO-92,T

....4 Q701 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW ,TO-92,T

....4 Q205 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW ,TO-92,T

....4 Q202 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW ,TO-92,T

....4 Q902 0504-001159 TR-DIGITAL;SRC1211M,NPN,400MW,10KOHM,TO-

....4 Q703 0504-001159 TR-DIGITAL;SRC1211M,NPN,400MW,10KOHM,TO-

....4 VX801S 1405-000187 VARISTOR;750V,1250A,12.5x7mm,TP

....4 R125 2001-000004 R-CARBON;200KOHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000005 R-CARBON;390ohm,5%,1/8W,AA,TP,1.8x3.2mm

....4 R125 2001-000008 R-CARBON;15KOHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000011 R-CARBON;75KOHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 J125 2001-000016 R-CARBON(S);1OHM,5%,1/2W ,AA,TP,2.4X6.4MM

....4 R301 2001-000016 R-CARBON(S);1OHM,5%,1/2W,AA,TP,2.4X6.4MM

....4 R843 2001-000019 R-CARBON(S);10OHM,5%,1/2W,AA,TP,2.4X6.4M

....4 R618 2001-000019 R-CARBON(S);10OHM,5%,1/2W,AA,TP,2.4X6.4M

....4 R409 2001-000022 R-CARBON(S);33OHM,5%,1/2W,AA,TP,2.4X6.4M

....4 R823 2001-000037 R-CARBON(S);330OHM,5%,1/2W,AA,TP,2.4X6.4

....4 R125 2001-000221 R-CARBON;1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000241 R-CARBON;1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000273 R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000319 R-CARBON;120KOHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000325 R-CARBON;120OHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000472 R-CARBON;2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000563 R-CARBON;27KOHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000591 R-CARBON;3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000645 R-CARBON;330KOHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000689 R-CARBON;390KOHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000739 R-CARBON;4.7MOHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000786 R-CARBON;47KOHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000793 R-CARBON;47OHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000857 R-CARBON;560OHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000890 R-CARBON;6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000924 R-CARBON;680OHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000947 R-CARBON;7.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-000969 R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R125 2001-001006 R-CARBON;82OHM,5%,1/8W,AA,TP,1.8X3.2MM

....4 R408 2001-001037 R-CARBON(S);0.39OHM,5%,1/2W,AA,TP,2.4X6.

....4 R504 2001-001062 R-CARBON(S);10MOHM,5%,1/2W,AA,TP,2.4X6.4

....4 R414 2001-001078 R-CARBON(S);15KOHM,5%,1/2W,AA,TP,2.4X6.4

....4 R831 2001-001088 R-CARBON(S);1KOHM,5%,1/2W,AA,TP,2.4X6.4M

....4 R806 2001-001108 R-CARBON(S);22KOHM,5%,1/2W,AA,TP,2.4X6.4

....4 R411 2001-001114 R-CARBON(S);270OHM,5%,1/2W,AA,TP,2.4X6.4

....4 R840 2001-001122 R-CARBON(S);3.9KOHM,5%,1/2W,AA,TP,2.4X6.

....4 R808 2001-001138 R-CARBON(S);390OHM,5%,1/2W,AA,TP,2.4X6.4

....4 R809 2001-001150 R-CARBON(S);470KOHM,5%,1/2W,AA,TP,2.4X6.

....4 R810 2001-001150 R-CARBON(S);470KOHM,5%,1/2W,AA,TP,2.4X6.

....4 R405 2001-001195 R-CARBON(S);82OHM,5%,1/2W,AA,TP,2.4X6.4M

....4 R503 2002-001008 R-COMPOSITION;1.8Kohm,10%,1/2W,AA,TP,3.7

....4 R502M 2002-001008 R-COMPOSITION;1.8Kohm,10%,1/2W,AA,TP,3.7

....4 R501M 2002-001008 R-COMPOSITION;1.8Kohm,10%,1/2W,AA,TP,3.7

Electrical Parts List

7-2 Samsung Electronics

Level Loc. No. Code No. Description ; Specification Remark Level Loc. No. Code No. Description ; Specification Remark

Electrical Parts List

Samsung Electronics 7-3

Level Loc. No. Code No. Description ; Specification Remark Level Loc. No. Code No. Description ; Specification Remark

....4 RX801S 2002-001011 R-COMPOSITION;3.3Mohm,5%,1/2W ,AA,TP,3.7x

....4 RY801S 2002-001012 R-COMPOSITION;8.2Mohm,5%,1/2W ,AA,TP,3.7x

....4 R413 2003-000592 R-METAL OXIDE(S);22ohm,5%,2W,AF,TP,4x12m

....4 R403 2003-000784 R-METAL OXIDE(S);7.5Kohm,5%,2W,AF,TP,4x1

....4 R827 2003-000998 R-METAL OXIDE;300ohm,5%,2W,AF,TP,3.9x10m

....4 R802 2003-001040 R-METAL OXIDE(S);47Kohm,5%,2W,AF,TP,3.9x

....4 R834 2003-001040 R-METAL OXIDE(S);47Kohm,5%,2W,AF,TP,3.9x

....4 R315 2003-002009 R-METAL OXIDE(S);390ohm,5%,2W,AF,TP,3.9x

....4 R303 2003-002152 R-METAL OXIDE;1OHM,5%,2W,AG,TP,6X16MM

....4 R402 2003-002178 R-METAL OXIDE(S);1Kohm,5%,2W,AG,TP,3.9x1

....4 R407 2003-002209 R-METAL OXIDE(S);47Kohm,5%,2W,AG,TP,3.9X

....4 R811 2003-002239 R-METAL OXIDE(S);100KOHM,5%,2W,AF,TP,3.9

....4 R812 2003-002239 R-METAL OXIDE(S);100KOHM,5%,2W,AF,TP,3.9

....4 R024 2004-001390 R-METAL(S);1Kohm,2%,1/2W,AA,TP,2.4x6.4mm

....4 R024 2004-001402 R-METAL(S);6.8Kohm,1%,1/2W,AA,TP,2.4x6.4

....4 R219 2004-001914 R-METAL;39Kohm,2%,1/8W,AA,TP,1.8x3.5mm

....4 R024 2004-004089 R-METAL(S);123Kohm,1%,1/2W,AA,TP,2.5x6.5

....4 R024 2004-004969 R-METAL(S);1.1Kohm,1%,1/2W,AA,TP,2.4x6.4

....4 R305 2008-000253 R-FUSIBLE(S);0.47ohm,5%,1W,AF,TP,3.9x10m

....4 R304 2008-000253 R-FUSIBLE(S);0.47ohm,5%,1W,AF,TP,3.9x10m

....4 R421 2008-000284 R-FUSIBLE(S);0.1OHM,10%,2W,AF,TP,3.9X10M

....4 R825 2008-000284 R-FUSIBLE(S);0.1OHM,10%,2W,AF,TP,3.9X10M

....4 R824 2008-000294 R-FUSIBLE(S);33ohm,5%,2W,AF,TP,3.9x10mm

....4 R505 2008-001031 R-FUSIBLE(S);1.8ohm,5%,1W,AF,TP,3.9x10mm

....4 R814 2008-001086 R-FUSIBLE(S);3.3ohm,5%,2W,AG,TP,3.9x12mm

....4 R420 2008-001110 R-FUSIBLE(S);68ohm,5%,2W,AG,TP,3.9X12mm

....4 C598 2201-000259 C-CERAMIC,DISC;0.18NF,10%,500V,Y5P,TP,5.

....4 C598 2201-000406 C-CERAMIC,DISC;0.27NF,10%,2KV,Y5P,TP,6.3

....4 C598 2201-000556 C-CERAMIC,DISC;0.47NF,10%,500V,Y5P,TP,5.

....4 C598 2201-000573 C-CERAMIC,DISC;0.047NF,5%,50V,C0G,TP,5X3

....4 C598 2201-000599 C-CERAMIC,DISC;0.56NF,10%,500V,Y5P,TP,5.

....4 C598 2201-000639 C-CERAMIC,DISC;0.68NF,10%,2KV,Y5P,TP,9X5

....4 C598 2201-000723 C-CERAMIC,DISC;4.7NF,20%,3KV,Y5U,TP,16X5

....4 C598 2201-000991 C-CERAMIC,DISC;0.56NF,10%,2KV,Y5P,TP,7.5

....4 C689 2202-000121 C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP

....4 C689 2202-000127 C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V

....4 C689 2202-000210 C-CERAMIC,MLC-AXIAL;270pF,10%,50V,Y5P,TP

....4 C689 2202-000253 C-CERAMIC,MLC-AXIAL;4.7nF,20%,16V,Y5R,TP

....4 C689 2202-000279 C-CERAMIC,MLC-AXIAL;47pF,5%,50V,SL,TP,3.

....4 C689 2202-000632 C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP

....4 C689 2202-000796 C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3

....4 C689 2202-000829 C-CERAMIC,MLC-AXIAL;0.82NF,10%,50V,Y5P,T

....4 C217 2301-000004 C-FILM,PEF;2.2nF,5%,100V,TP,5.5X10X2.9,5

....4 C234 2301-000004 C-FILM,PEF;2.2nF,5%,100V,TP,5.5X10X2.9,5

....4 C248 2301-000013 C-FILM,PEF;4.7nF,5%,100V,TP,10.5x12.5x6.

....4 C227 2301-000014 C-FILM,PEF;6.8nF,5%,100V,TP,5.8x12.5mm,5

....4 C804 2301-000016 C-FILM,PEF;22nF,5%,100V,TP,7.2x4.5x9.0mm

....4 C109 2301-000016 C-FILM,PEF;22nF,5%,100V,TP,7.2x4.5x9.0mm

....4 C603 2301-000020 C-FILM,PEF;27nF,5%,100V,TP,7.3x4x12.5mm,

....4 C904 2301-000148 C-FILM,PEF;10nF,5%,100V,TP,7x3.2x7mm,5mm

....4 C407 2301-000148 C-FILM,PEF;10nF,5%,100V,TP,7x3.2x7mm,5mm

....4 C118 2301-000148 C-FILM,PEF;10nF,5%,100V,TP,7x3.2x7mm,5mm

....4 C606 2301-000192 C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm

....4 C707 2301-000204 C-FILM,PEF;2.7nF,5%,50V,TP,7.4x3.9x13mm,

....4 C502 2301-000213 C-FILM,PEF;220nF,5%,250V,TP,21.5x11,7.5

....4 C805 2301-000233 C-FILM,PEF;3.9nF,10%,100V,TP,5.8x12.5mm,

....4 C309 2301-000253 C-FILM,PEF;39NF,5%,100V,TP,7.5X4.5X12.5M S.N.A

....4 C420 2301-001065 C-FILM,MPPF;47nF,5%,630V,TP,19x15.5x7,7.

....4 C806 2301-001435 C-FILM,PPF;1.5nF,5%,1.2kV,TP,15x8x12.5mm

....4 C312 2305-000149 C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5

....4 C301 2305-000285 C-FILM,MPEF;220NF,5%,100V,TP,10.5X5.5X15

....4 C613 2305-000289 C-FILM,MPEF;220nF,5%,63V,TP,-,5mm

....4 C233 2305-000289 C-FILM,MPEF;220nF,5%,63V,TP,-,5mm

....4 C216 2305-000289 C-FILM,MPEF;220nF,5%,63V,TP,-,5mm

....4 C215 2305-000289 C-FILM,MPEF;220nF,5%,63V,TP,-,5mm

....4 CR405S 2305-000382 C-FILM,MPEF;4.7nF,5%,400V,TP,-,5mm

....4 C901 2305-000412 C-FILM,MPEF;470nF,5%,63V,TP,-,5mm

....4 C207 2305-000412 C-FILM,MPEF;470nF,5%,63V,TP,-,5mm

....4 C618 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m

....4 C803 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m

....4 C819 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m

....4 C913 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m

....4 C230 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m

....4 C103 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m

....4 C208 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m

....4 C210 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m

....4 C218 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m

....4 C225 2301-001664 C-FILM,MPE-PPF;100nF,3%,50V,TP,20x16x8.5 S.N.A

....4 C701 2401-000025 C-AL;100uF,20%,16V,GP,TP,6.3x11,5

....4 C701 2401-000050 C-AL;10uF,20%,16V,GP,TP,5x11,2.5

....4 C701 2401-000262 C-AL;100uF,20%,160V,HR,TP,16x25,7.5

....4 C701 2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5

....4 C701 2401-000360 C-AL;100uF,20%,50V,GP,TP,8x11.5,5

....4 C701 2401-000365 C-AL;100uF,20%,50V,WT,TP,10x12.5mm,

....4 C701 2401-000430 C-AL;10uF,20%,250V,GP,TP,10x16mm,5m

....4 C701 2401-000471 C-AL;10uF,20%,50V,BP,TP,5x11,5mm

....4 C701 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5

....4 C701 2401-000481 C-AL;10uF,20%,50V,WT,TP,5x11,5

....4 C701 2401-000560 C-AL;1uF,20%,160V,GP,TP,6.3x11,5

....4 C701 2401-000603 C-AL;1UF,20%,50V,GP,TP,5X11,2

....4 C701 2401-000649 C-AL;2.2uF,20%,50V,BP,TP,5x11,5

....4 C701 2401-000660 C-AL;2.2uF,20%,50V,GP,TP,5x11,5

....4 C701 2401-000722 C-AL;2200uF,20%,25V,WT,TP,16x25,7.5

....4 C701 2401-000758 C-AL;0.22UF,20%,50V,GP,TP,5X11,5

....4 C701 2401-000913 C-AL;22uF,20%,16V,GP,TP,5x11,5

....4 C701 2401-000927 C-AL;22uF,20%,250V,GP,TP,13x20,5

....4 C701 2401-000962 C-AL;22uF,20%,50V,GP,TP,5x11,5

....4 C701 2401-001101 C-AL;330uF,20%,16V,GP,TP,8x11.5,5

....4 C701 2401-001176 C-AL;33uF,20%,25V,GP,TP,5x11,5

....4 C701 2401-001192 C-AL;33uF,20%,50V,GP,TP,6.3x11,5

....4 C701 2401-001232 C-AL;4.7uF,20%,250V,GP,TP,10x12.5,5

....4 C701 2401-001486 C-AL;47uF,20%,160V,HR,TP,13x20mm,5m

....4 C701 2401-001989 C-AL;4.7uF,20%,50V,BP,TP,5x11,5

....4 C701 2401-001998 C-AL;1000uF,20%,25V,GP,TP,10x20,5mm

....4 C701 2401-002288 C-AL;470uF,20%,25V,WT,TP,10x20,5

....4 C701 2401-002619 C-AL;47uF,20%,25V,GP,TP,5x11,5

....4 C701 2401-003028 C-AL;100uF,20%,25V,WT,TP,6.3x11,5

....4 L904 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm

....4 L902 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm

....4 L202 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm

....4 L103 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm

....4 J142 2701-000115 INDUCTOR-AXIAL;10uH,10%,3x7mm

....4 L404 2701-000142 INDUCTOR-AXIAL;1uH,10%,2.5x3.4mm

....4 L302 2701-000142 INDUCTOR-AXIAL;1uH,10%,2.5x3.4mm

....4 L301 2701-000142 INDUCTOR-AXIAL;1uH,10%,2.5x3.4mm

....4 L903 2701-000158 INDUCTOR-AXIAL;22uH,10%,2.5x3.4mm

....4 L201 2701-000158 INDUCTOR-AXIAL;22uH,10%,2.5x3.4mm

....4 L205 2701-000158 INDUCTOR-AXIAL;22uH,10%,2.5x3.4mm

....4 L405 2701-000159 INDUCTOR-AXIAL;22uH,10%,4.2x9.8mm

....4 L102 2701-000159 INDUCTOR-AXIAL;22uH,10%,4.2x9.8mm

....4 L104 2701-000168 INDUCTOR-AXIAL;3.3uH,5%,2.5x3.4mm

....4 L706 2701-000184 INDUCTOR-AXIAL;4.7uH,10%,2.5x3.4mm

....4 L703 2701-000184 INDUCTOR-AXIAL;4.7uH,10%,2.5x3.4mm

....4 L204 2701-000184 INDUCTOR-AXIAL;4.7uH,10%,2.5x3.4mm

....4 L804 2701-001030 INDUCTOR-AXIAL;43uH,10%,5x14mm

....4 X901 2801-003937 CRYSTAL-UNIT ;12MHz,25ppm,28-AAM,30pF,30o

....4 F101 2901-000297 FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,-

....4 Z202 2903-001240 FILTER-CERAMIC;TR,5.5MHz,-,28dB,-,TP,-

....4 Z203 2903-001246 FILTER-CERAMIC;TR,5.5MHz,-,-,-,TP,multi.

....4 G101 3301-000287 CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500,

....4 SW905 3404-000244 SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP

....4 SW904 3404-000244 SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP

....4 SW903 3404-000244 SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP

....4 SW902 3404-000244 SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP

....4 SW901 3404-000244 SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP

....4 FD801S 3601-001163 FUSE-AXIAL LEAD;125V,7A,-,EPOXY,2.4X7.1M

....4 F801B 3602-000114 FUSE-HOLDER;-,-,30mohm

....4 F801A 3602-000114 FUSE-HOLDER;-,-,30mohm

....4 CN906 3711-002642 CONNECTOR-HEADER;BOX,3P,1R,2.5mm,STRAIGH

....4 EL804 6042-000001 EYELET;ID2.2,OD2.7,L3.1,NI+SN,BSP3-1/2H S.N.A

....4 EL802 6042-000001 EYELET;ID2.2,OD2.7,L3.1,NI+SN,BSP3-1/2H S.N.A

....4 EL801 6042-000001 EYELET;ID2.2,OD2.7,L3.1,NI+SN,BSP3-1/2H S.N.A

....4 EL404 6042-000001 EYELET;ID2.2,OD2.7,L3.1,NI+SN,BSP3-1/2H S.N.A

....4 EL403 6042-000001 EYELET;ID2.2,OD2.7,L3.1,NI+SN,BSP3-1/2H S.N.A

....4 EY819 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY821 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY822 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY823 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY824 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY818 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY807 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY808 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY809 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY810 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY813 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY825 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY851 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY852 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY853 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY860 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY861 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY850 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY827 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY828 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY829 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY830 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY833 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY803 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY406 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY407 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY408 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY409 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY410 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY405 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY101 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY401 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY402 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY403 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY404 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY411 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY422 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY423 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY501 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY801 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY802 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY420 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY412 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY414 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY415 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY416 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 EY419 6042-000002 EYELET;ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H S.N.A

....4 FIX02 AA37-00001A CONNECTOR-FBT FIX PIN;JM-3500,CPTTV,0.36

....4 FIX01 AA37-00001A CONNECTOR-FBT FIX PIN;JM-3500,CPTTV,0.36

....4 PCB AA41-00849A PCB-MAIN;CS21D8,FR-1,1L,A,1.6T,245X245,M S.N.A

....4 GT803 AA60-40014A PIN-GT,ASSY;AUTO S.N.A

....4 GT804 AA60-40014A PIN-GT,ASSY;AUTO S.N.A

....4 GT805 AA60-40014A PIN-GT,ASSY;AUTO S.N.A

....4 GT806 AA60-40014A PIN-GT,ASSY;AUTO S.N.A

....4 GT807 AA60-40014A PIN-GT,ASSY;AUTO S.N.A

....4 GT101 AA60-40014A PIN-GT,ASSY;AUTO S.N.A

....4 GT501 AA60-40014A PIN-GT,ASSY;AUTO S.N.A

....4 GT502 AA60-40014A PIN-GT,ASSY;AUTO S.N.A

....4 GT801 AA60-40014A PIN-GT,ASSY;AUTO S.N.A

....4 GT802 AA60-40014A PIN-GT,ASSY;AUTO S.N.A

..2 T0091 AA95-03195A ASSY SUB PCB-A/V SIDE;KS1A(MAC),PAL,MONO ...3 0202-000187 SOLDER-WIRE FLUX;-,RS60S,D1.2,63Sn/37Pb S.N.A ...3 C701 2401-000025 C-AL;100uF,20%,16V,GP,TP,6.3x11,5 ...3 JE601 3722-000144 JACK-PHONE;6P/5C,3.6PI,MBAG,BLACK,...3 JA702 3722-001342 JACK-PIN;1P,3.4MM,NI,YEL,...3 JA701 3722-001343 JACK-PIN;1P,3.4MM,NI,WHT,...3 T0081 6003-001023 SCREW-TAPTITE;RWH,+,B,M3,L10,ZPC(YEL),SW S.N.A ...3 T0076 AA39-20112E LEAD CONNECTOR-ASSY ;,9P,300,YBNH025-09,6 ...3 AA96-01630A ASSY COVER P-HOLDER AV;14F10,HIPS HB,G43 S.N.A

....4 T0010 AA61-01315A HOLDER-AV;14F10,HIPS,G4309 SV012P,HB S.N.A

....4 AA64-01729C INLAY AV;21F5,PS SHEET,T0.3,BLK,KS1A SIL S.N.A

...3 AA97-07191A ASSY AUTO-A/V SIDE;,KS1A,PAL,AA95-01317A S.N.A

....4 RE01 2001-001153 R-CARBON(S);47OHM,5%,1/2W,AA,TP,2.4X6.4M

....4 C689 2202-000121 C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP

....4 C689 2202-000222 C-CERAMIC,MLC-AXIAL;3.3nF,20%,16V,Y5P,TP

....4 RE04 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm

....4 LE01 2701-000159 INDUCTOR-AXIAL;22uH,10%,4.2x9.8mm

....4 PCB AA41-00412B PCB-A/V SIDE;CS21F5,FR-1,1L,B,1.6T,245X2 S.N.A

ASSY FIXING

1 AA91-06463A ASSY FIXING;CS14F10MJ0XBWT,KS1A S.N.A ..2 T0076 AA39-20010D LEAD CONNECTOR-ASSY;,1P,400,YFH800-01,S,

..2 AA65-30009A CLAMPER CORE-FBT;-,ABS,V0,-,BLK,- S.N.A ..2 AA65-30018A CLAMPER CORE-WIRE;DONG-A,NYLON-66,-,-,-, S.N.A ..2 CLAMP AA65-30018A CLAMPER CORE-WIRE;DONG-A,NYLON-66,-,-,-, S.N.A ..2 AA65-30111A CLAMPER CORE-WIRE;ALL MODEL,NYLON,V0,-,W S.N.A ..2 T0066 AA96-20109B ASSY POWER CORD;-,CP2/NO(4.0),H/C250,KKP S.N.A ...3 3811-000401 WIRE-PVC CU;BCWA,300V,ROLL,17/0.16mm,#22 S.N.A ...3 T0077 AA39-10006X CBF POWER CORD;-,KKP419C,KLCE-2F,2.286MT ...3 AA61-20284A HOLDER;P-CORD,PP,-,-,-,BLK,VO,KE-002 S.N.A

ASSY ACCESSORY

1 M0016 AA92-07884A ASSY ACCESSORY ;CS14F10MJ0XBWT,KS1A S.N.A ..2 6801-001073 CARD-REGISTRATION;RUS,XEV ,RUS,MOJO100,-, S.N.A

..2 T0080 AA26-90001C TRANS MATCHING;-,300ohm/75ohm,PAL,40-890 ..2 T0075 AA42-00003A ANT ROD;-,3S,720mm,ABS,UL/CSA,..2 T0074 AA59-00198F REMOCON;,TM59,DREAM,24,L/GRA Y,MONO,PAL-T ..2 AA68-00816B CARD WARRANTY-01;,RUSSINA,2,W/P 120G,BOT S.N.A ..2 T0269 AA68-01120A MANUAL SERVICE;-,-,CIS,A4,6PAGE(FOLD),W/ S.N.A ..2 CIS AA68-01296E MANUAL USERS;15K2/15K9,RUS,W/P100G,KS1A/ ..2 AA68-01402A MANUAL-GOOD WILL LETTER;,CIS,B5,1PAGE,A/ S.N.A ..2 AA69-00862A BAG PE;-,HDPE PE FOAM,T0.03,W400,H240,-, S.N.A

ASSY P/MATERIAL

1 AA92-07949A ASSY P/MATERIAL;14F10 S.N.A ..2 AA60-40006A PIN-STAPLE;AUTO,33X17.8X2.4,H18,33X17.8X S.N.A

..2 AA69-00305A BAG AIR;ALL,LDPE,1000,500,CLR, S.N.A ..2 AA69-00306A BAG AIR;LDPE,-,1800,1000,CLR,ASSY,ALL,- S.N.A ..2 AA69-00744B BAG-SHEET;-,HDPE PE FOAM,T0.015,W900,H80 S.N.A

Electrical Parts List

7-4 Samsung Electronics

Level Loc. No. Code No. Description ; Specification Remark Level Loc. No. Code No. Description ; Specification Remark

Electrical Parts List

Samsung Electronics 7-5

Level Loc. No. Code No. Description ; Specification Remark Level Loc. No. Code No. Description ; Specification Remark

ASSY COVER FRONT

1 M0001 AA90-04709A ASSY COVER FRONT;CS20F10MJ0XBWT S.N.A ..2 T0081 6003-001019 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR

..2 SC016 AA60-10050R SCREW-ASSY ;-,SWRCH18A,M5,L31.5,HH,+,WC,- S.N.A ..2 T0081 AA60-10050T SCREW-TAPPING;-,SWRCH18A,M4,L20,RH,+,2S, S.N.A ..2 AA65-30107A CLAMPER CORE-D,COIL;20~22 INCH,NYLON 66, S.N.A ..2 T0003 AA96-01628A ASSY COVER P-FRONT;20F10(TTSEC),HIPS HB, ...3 T0081 6003-001019 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR ...3 T0081 6003-001019 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR ...3 AA61-40113A STOPPER-PCB;501H,HIPS,-,-,HB,NTR,- S.N.A ...3 CIS7 AA61-60003J SPRING ETC-CS;-,SUS304,-,-,OD6,N7,OD6,-, S.N.A ...3 CIS3 AA64-03518A CABINET FRONT;20F10,(TTSEC),HIPS,HB,G430 S.N.A ...3 T0022 AA64-03522A KNOB CONTROL;F10,ABS,HB,G3676,SVM3012 S.N.A ...3 T0023 AA64-03523A KNOB POWER;F10,ABS,HB,G3676,SVM3012 S.N.A ...3 AA64-03524A WINDOW REMOCON-LED;F10,PC,CLEAR S.N.A ...3 T0057 AA64-70123B BADGE-BRAND;ALL,AL,8.5,L50,BLK,SILVER,SA S.N.A ...3 AA65-30105A CLAMPER CORE-WIRE;ALL MODEL,NYLON 66,V2, S.N.A ...3 CIS5 AA96-01188A ASSY SPEAKER P;16OHM,3001-001008,AA39-20

....4 T0082 3001-001008 SPEAKER;5W,16ohm,90dB,180Hz

....4 T0076 AA39-20500G LEAD CONNECTOR-ASSY;,3(2)P,300MM,67096-0

...3 AA61-00721C HOLDER-RAIL;H4,HIPS,V0,GRAY S.N.A ...3 T0081 6003-001019 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR

ASSY COVER REAR

1 M0002 AA90-04712A ASSY COVER REAR;20F10,FV2,GR503,HIPS,KS1 S.N.A ..2 T0015 AA64-03006A CABINET-BACK;21F3,HIPS,FV2,GR503

..2 AA65-30008A CLAMPER CORE-CORD;-,PE,HB,-,BLK,- S.N.A

ASSY CHASSIS

1 M0017 AA91-06441A ASSY CHASSIS;CS20F10MJ0BWT,KS1A S.N.A ..2 T0091 AA95-03196A ASSY SUB PCB-A/V SIDE;KS1A(MAC),MONO,20F

...3 JE601 3722-000144 JACK-PHONE;6P/5C,3.6PI,MBAG,BLACK,...3 T0081 6003-001023 SCREW-TAPTITE;RWH,+,B,M3,L10,ZPC(YEL),SW S.N.A ...3 T0081 6003-001023 SCREW-TAPTITE;RWH,+,B,M3,L10,ZPC(YEL),SW S.N.A ...3 T0076 AA39-20112E LEAD CONNECTOR-ASSY;,9P,300,YBNH025-09,6 ...3 AA63-00632A COVER-AV;21F3,HIPS,HB,BLK S.N.A ...3 AA96-01632A ASSY COVER P-HOLDER AV;21F10,HIPS HB,G43 S.N.A

....4 T0010 AA61-01314A HOLDER-AV;20F10,HIPS,G4309,SV012P,HB

....4 AA64-03517A INLAY AV-A;20F10,PS SHEET,T0.3,SILVER,MO S.N.A

...3 AA97-14157A ASSY AUTO-SUB;KS1A(MAC),MONO,20F10,21F10 S.N.A

....4 RE01 2001-001153 R-CARBON(S);47OHM,5%,1/2W,AA,TP ,2.4X6.4M

....4 C689 2202-000121 C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP

....4 C689 2202-000222 C-CERAMIC,MLC-AXIAL;3.3nF,20%,16V,Y5P,TP

....4 C701 2401-000025 C-AL;100uF,20%,16V,GP,TP,6.3x11,5

....4 LE01 2701-000159 INDUCTOR-AXIAL;22uH,10%,4.2x9.8mm

....4 0 AA41-00918A PCB-USB;CS21F10,FR-1,1L,A,1.6T,245*245,K S.N.A

....4 LE04 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm

...3 JA701 3722-001342 JACK-PIN;1P,3.4MM,NI,YEL,...3 JA702 3722-001343 JACK-PIN;1P,3.4MM,NI,WHT,..2 T0073 AA94-13238R ASSY PCB MAIN;MAC,KS1A ...3 0202-000187 SOLDER-WIRE FLUX;-,RS60S,D1.2,63Sn/37Pb S.N.A ...3 T0090 0502-001160 TR-POWER;2SD2499,NPN,50000mW,TO-3P,BK,8...3 IC112 1103-001106 IC-EEPROM;C81DC,1028x8Bit,DIP,8P,300MIL, ...3 NT802S 1404-001045 THERMISTOR-NTC;4.7ohm,15%,2900K,35.0mW,T ...3 P803T 1404-001265 THERMISTOR-PTC;4.5OHM/100OHM,+30/-20%,22 ...3 C598 2201-000446 C-CERAMIC,DISC;3.3NF ,20%,400V,Y5U,TP,15X ...3 CR402S 2306-000195 C-FILM,MPPF;360nF,5%,400V ,TP,26x19x11.5, ...3 CX801S 2306-000318 C-FILM,MPPF;220nF,20%,250V ,TP,-,22.5mm

...3 CR410S 2306-000327 C-FILM,MPPF;6.3nF,3%,1.6KV ,TP,28.5x18x10 ...3 C701 2401-002213 C-AL;150uF ,+30-10%,450V,GP,BK,25x35 ...3 SF101S 2904-001063 FILTER-SAW AV;38.9MHz,SIP5K,TP,18.5dB,B/ ...3 SW801S 3403-001134 SWITCH-PUSH;250V ,5A,DPST,ON-OFF,...3 FP801S 3601-000281 FUSE-CARTRIDGE;250V,4A,TIME-LAG,GLASS,5. ...3 V999S 3704-001105 SOCKET-CRT;11P ,20PI,26.5PI,NI,...3 JS701 3722-000497 JACK-PIN;4P,3.4mm,SN,BLK,...3 T0119 AA09-00354A IC MICOM;TDA9381/N2/3I,SPM-802EEN4,64P,3 ...3 T801S AA26-00134A TRANS SWITCHING;,CS21S5T ,160V~260V,PM2 P ...3 T444S AA26-00201A TRANS FBT;FCA173B,KS1A-1,3.8mH,FERRITE,1 ...3 T401 AA26-50001B TRANS-HORIZ.DRIVE;-,-,-,7.1mH,-,-,102uH, ...3 LR401S AA27-00053A COIL LINEARITY;-,193uH,DR10X10 C:4.35,7. ...3 LX801S AA29-30001B FILTER LINE NOISE;-,-,-,-,27MH,-,-,-,ST, ...3 RM901 AA32-00015A MODULE REMOCON;FRP-3521H31,38KHZ,940MM,M ...3 T0076 AA39-20620C LEAD CONNECTOR-ASSY ;,9P,500MM,YBNH250-09 ...3 TU01S AA40-00067A TUNER;TAEL-G671D,-,P AL,181CH,38.9MHz,-,7 ...3 GT301 AA60-40012D PIN-GT,ASSY ;T1.6,6-12.5-,NYLON66 S.N.A ...3 IC801S AA96-00242D ASSY H/S;SCREWAA62-30186B,5Q0765RTH,OIL S.N.A

....4 CIS 0205-001027 OIL-SILICON;G746,-,- S.N.A

....4 T0086 1203-002916 IC-PWM CONTROLLER;KA5Q0765RTH-YDTU,TO-22

....4 T0081 6003-000333 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW S.N.A

....4 CIS AA62-30186B HEAT SINK-ES;-,-,-,SILVER,171J + COVER-H S.N.A

....4 CIS AA63-30189A COVER-HEA TSINK;-,PC-ABS,T0.8,-,-,V0,NTR, S.N.A

...3 IC301 AA96-00244M ASSY H/S;SCREWAA64-00046A,LA78040N,OIL S S.N.A

....4 CIS 0205-001027 OIL-SILICON;G746,-,- S.N.A

....4 T0088 1204-002121 IC-VERTICAL DEF.;LA78040N,TO220,7P,-,PLA

....4 T0081 6003-000335 SCREW-TAPTITE;RH,+,2S,M3,L8,ZPC(YEL),SWR S.N.A

....4 CIS AA62-00046A HEA T SINK-PS;-,-,T1.0,-,D1(DREAM) 60X25X S.N.A