The lamp used in a projection TV has a limited lifespan. For the best screen quality it needs to be
replaced periodically. After replacing the lamp, the screen quality will be bright and clear as new.
• When do I need to replace it?
It should be replaced when the screen becomes darker, less clear or when all three LEDs on the front
(Timer, Lamp, & Temp.) are flashing.
• Check before lamp replacement
1. The lamp must be the same code number and type.
2. The lamp type is indicated on the right side of the TV. It is also indicated on the lamp case.
3. After checking the code number for the lamp, give the code number to the store where you
purchased the TV or to a Samsung Service center.
• Caution
1. Replace with the correct code numbered lamp to avoid damage to the TV.
2. Turn the power off and wait for 30 minutes before replacing the lamp as it will be hot.
3. Do not touch the glass part of the lamp with your bare hands nor insert any foreign object inside
the cover as it may cause poor screen quality, electric shock or fire.
4. Do not place the old lamp near flammable objects or within the reach of children.
When installing the product, make sure to keep it away from
the wall (more than 10cm/4 inches) for ventilation purposes.
• Poor ventilation may cause an increase in the internal
temperature of the product, resulting in a shortened
component life and degraded performance.
English - 6
Page 7
• For replacement, you will need a 5.91 Inches-long Phillips screwdriver and a pair of gloves.
Unplug TV, then use a
1
screwdriver to remove the
screw.
Remove the Lamp cover.
2
Remove the screws securing
3
the Lamp by using a
screwdriver.
Separate the Lamp from the
engine by holding the handle
4
and pulling it out.
To reinstall the Lamp, follow
5
these steps in reverse order.
NOTES
• Be sure the replacement Lamp is the same type.
• After replacing the lamp, align the lamp cover with the groove and secure the screw.
• The TV will not turn on if the lamp cover is not correctly closed (as this will activate the
protective circuit).
English - 7
Page 8
Your New Wide TV
List of Features
Your TV was designed and engineered using the latest technology. It is a full-featured, high-performance
unit that exceeds industry standards. In addition, it has these special features:
• Easy-to-operate remote control
• Easy-to-use on-screen menu system you can access from the side panel or remote control
• Automatic timer to turn the TV on and off at any time you choose
• Adjustable picture and sound settings and the ability to memorize your favorite settings
• Automatic channel tuning for up to 181 channels
• A special filter to reduce or eliminate reception problems
• Fine tuning control for the sharpest picture possible
• A built-in multi-channel sound decoder for stereo and bilingual listening
• Built-in, dual channel speakers
• A special sleep timer
• Picture-in-Picture capability that lets you watch two channels at once
• Widescreen TV with adjustable image size
• Life-like clear images provided by DNle technology
• My Color Control Mode for corresponding with your color style
• Color weakness Mode
Accessories
Once you have unpacked your TV, check to make sure that you have all the parts shown here.
If any piece is missing or broken, call your dealer.
Owner’s InstructionsPower Cord
(3903-000144)
Remote Control
(BP59-00048C)/
AAA Batteries
English - 8
Page 9
Side Panel Buttons
The buttons on the right side panel control your TV’s basic features, including the on-screen menu
system. To use the more advanced features, you must use the remote control.
Press to switch between viewing TV programs and signals from connected components.
Press to see the on-screen menu.
Press to lower or raise the volume and to select items when using the on-screen menu.
Press to change channels and move between items on the on-screen menu.
Press to activate (or change) a particular item.
Side Panel Jacks
Use the right side panel jacks to connect a component that is used only occasionally (a camcorder
or video game, for example).
Connect the video signal from a camcorder or video game.
Connect the audio signal from a camcorder or video game.
Connect an S-video signal from a camcorder or video game.
(S-Video 3 jack and Audio L/R input 3 are used in conjunction.)
English - 9
Page 10
Your New Wide TV
Front Panel LED Indicators
The three lights on the front panel indicate the status of your TV.
POWER
Press to turn the TV on and off.
Remote Control Sensor
Aim the remote control towards this spot on the TV.
: Light is On
: Light is Blinking
: Light is Off
TIMER
• It takes about 30 seconds for the TV to warm up, so normal brightness may not appear immediately.
• The TV has a fan to keep the inside lamp from overheating. You’ll occasionally hear it working.
LAMPSTAND BY/TEMPIndication
Standby state.
The picture will automatically appear in about 15 seconds.
Auto Timer ON/OFF has been set and the set will automatically be
turned on in about 25 seconds.
A cooling fan inside the set is not operating normally.
Lamp cover on rear of the set is not properly shut.
Check if the ventilation hole on the rear of the set is blocked, because if
the inner temperature is too high, the power will shut off.
Lamp may be defective. Please contact a certified technician.
English - 10
Page 11
Rear Panel Jacks
Use the rear panel jacks to connect components such as a VCR. You can connect different components
such as VCRs, Set-Top Box and a DVD player etc., because there are two sets of video input jacks and
three set of component video input jacks on the rear panel of your TV. For more information, please see
“Connections”.
Œ
ANTENNA terminals
Two independent cables or antennas can be connected to these terminals.
Use “ANT 1 IN” and “ANT 2 IN” terminals to receive a signal from
VHF/UHF antennas or your cable system. Use the “ANT 1 OUT” terminal to
send the signal being received by the “ANT 1 IN” terminal out to another
component (such as a Cable Set-Top Box). The PIP channel can be received
only when a signal source is connected to “ANT 1 IN”.
´
S-VIDEO INPUT jacks
Connects an S-Video signal from an S-VHS VCR or DVD player.
ˇ
VIDEO/AUDIO INPUT jacks (VCR1, VCR2)
Connect video/audio signals from external sources, such as a VCR or DVD
players.
¨
VIDEO/AUDIO OUTPUT jacks
Sends a video signal from the TV to an external source, such as a VCR.
Note: It is available only in RF, Video and S-Video modes.
ˆ
Component1, 2 jacks (Y, PB, PR, L, R)
Use these jacks to connect the component video/audio signals from a DVD
player or a Set-Top Box when using the component video input jacks.
Ø
PC AUDIO INPUT jacks
Connect these to the audio output jacks on your PC.
∏
PC VIDEO INPUT jack
Connect these to the video output jack on your PC .
”
DVI (Digital Video Interface) AUDIO INPUT jacks
Connect to the digital audio output jacks for device with DVI output.
’
DVI (Digital Video Interface) VIDEO INPUT jack
Connect to the digital video output jack for device with DVI output.
˝
HDMI (High Definition Multimedia Interface)
VIDEO/AUDIO INPUT jack
Connect to the HDMI jack for device with HDMI output.
Ô
SERVICE
This jack is for repair and software upgrades.
English - 11
Page 12
Your New Wide TV
Remote Control
You can use the remote control up to about 23 feet from the TV. When using the remote control, always
point it directly at the TV. You can also use your remote control to operate your VCR, Cable box, DVD
player or some Samsung Set-top boxes. See pages 46~47 for details.
1. POWER
Turns the TV on and off.
2. S.MODE
Adjust the TV sound by selecting one of the
preset factory settings (or select your personal,
customized sound settings.)
3. P.MODE
Adjust the TV picture by selecting one of the
preset factory settings (or select your personal,
customized picture settings.)
4. +100
Press to select cable channels over 100 on TV.
5. VOL +, VOL
Press to increase or decrease the volume.
-
6. MUTE
Press to mute the TV sound.
7. FAV.CH (Favorite Channel)
Press to switch between your favorite channels.
8. MENU
Displays the main on-screen menu.
9. STILL
Press to stop the action during a particular
scene. Press again to resume normal video.
10. P.SIZE
Press to change the picture size.
11. MODE
Selects a target device to be controlled by the
Samsung remote control (i.e., TV, STB, VCR,
CABLE, or DVD).
12. PRE-CH
Tunes to the previous channel.
13. SOURCE
Press to display all of the available video
sources (i.e., TV, Set-Top Box, VCR, DVD, DTV,
PC).
14. CH , CH
Press to change channels.
15. INFO
Press to display information on the TV screen.
16. EXIT
Press to exit the menu.
17. ▲, ▼, œ, √, ENTER
Press to select highlight up, down, left, or right.
While using the on-screen menus, press the
ENTER to activate (or change) a particular item.
18. MTS (Multichannel
Television Stereo)
Press to choose Stereo, Mono or SAP (Secondary
Audio Program).
19. SRS
Activates TruSurround.
20. ADD/DEL
Press to add or erase channels in the TV’s
memory.
Use the ADD/DEL button to memorize and erase
the fine tuning after fine tuning channels.
21. SLEEP
Press to select a preset time interval for
automatic shutoff.
22. PIP (Picture In Picture)
Activates PIP.
23. SET
Used during set up of this remote control,
so that it will work compatibly with other devices
(some Samsung Set-top boxes, VCR, Cable box,
DVD, etc.)
24. DNIe (Digital Natural
Image engine)
Activates DNIe.
25. PIP Controls
SIZE; Press to select the size of PIP window.
SWAP; Press to exchange the video signal that
is currently displayed on the main screen with
the signal in the PIP window.
CH/; Press to display the available
channels in sequence. (These buttons change
channels in the PIP window only.)
26. VCR/DVD Controls
Controls VCR or DVD functions: Rewind, Stop,
Play/Pause, Fast Forward.
27. RESET
If your remote control is not functioning
properly, take out the batteries and press the
reset button for about 2~3 seconds. Re-insert
the batteries and try using the remote control
again.
English - 12
Page 13
Installing Batteries in the Remote Control
With normal use, the batteries in the remote control should last about a year. If you notice a performance
degradation while using the remote, the batteries may need to be replaced. Make sure you replace both
batteries and do not mix old and new batteries in the remote control. If you won’t be using the remote
control for a long time, remove the batteries and store them in a cool dry place.
Slide the back cover all the way out
to open the battery compartment of
1
the remote control.
Install two AAA size batteries.
Make sure to match the “+” and
2
“–” ends of the batteries with the
diagram inside the compartment.
Slide the cover back into place.
3
English - 13
Page 14
SAMSUNG
Page 15
Connections
Page 16
Connections
Connecting VHF and UHF Antennas
If you do not have a cable system, you will need to connect an antenna to your TV.
Antennas with 300-ohm Flat Twin Leads
If your antenna looks like this: it has 300-ohm flat twin leads.
Place the wires from the twin
leads under the screws on the
1
300-75 ohm adaptor (not
supplied). Use a screwdriver
to tighten the screws.
Plug the adapter into the
“ANT 1 IN” terminal on the
2
rear panel.
1
English - 16
Antennas with 75-ohm Round Leads
If your antenna looks like this: it is an antenna with 75-ohm round leads.
Plug the antenna lead into the
“ANT 1 IN” terminal on the
rear panel.
Page 17
Separate VHF and UHF Antennas
If you have two separate antennas for your TV (one VHF and one UHF), you must combine the
two antenna signals before connecting the antennas to the TV. This procedure requires an optional
combiner-adaptor (available at most electronics shops).
Connect both antenna
leads to the combiner.
1
Plug the combiner into the
“ANT 1 IN” terminal on
2
the rear panel.
English - 17
Page 18
Connections
Connecting Cable TV and VCR
You can connect different cable systems to your TV, including cable without a cable box, and
cable with a cable box that descrambles some or all channels.
Cable without a Cable Box
If you want to connect cable, and you do not need to use a cable box:
Plug the incoming cable
into the “ANT 1 IN”
1
terminal on the rear panel.
Cable with a Cable Box that Descrambles All Channels
Find the cable that is
connected to the
1
ANTENNA OUT terminal
on your cable box. This
terminal might be labeled
“ANT OUT”, “VHF OUT”
or simply, “OUT”.
Connect the other end of
this cable to the “ANT 1
2
IN” terminal on the rear
panel.
English - 18
Page 19
Connecting a Cable Converter Box
This connection allows you to watch cable and premium channels. You should keep your TV
selected to “ANT 1 IN” so that you can use the TV features. When viewing premium channels,
select “ANT 2 IN” and tune the TV to channel 3 or 4 (whichever channel is vacant in your area),
then use the converter box to change channels. You will need two coaxial cables.
NOTES
• When you use a converter box with
From
Cable
your TV, there may be features that you
can not program using the remote
control, such as programming your
favorite channels and blocking
channels.
• The output from “ANT 1 OUT” is
available when select “Ant.2” in the
“Antenna“ channel menu.
Connecting a Cable Converter Box and a VCR
This connection allows you to watch and record basic and premium cable channels, as well as
watch videotapes. You should keep your TV selected to “ANT 1 IN” so that you can use the TV’s
features. When viewing premium channels or recording with the VCR, select “ANT 2 IN”
(whichever channel is vacant in your area), then use the converter box to change channels.
From
Cable
TV Rear Panel
Stereo VCR
Caution: If you want to record one channel
while watching another channel, a splitter
(not included) must be added between the
cable and “ANT 1 IN”. One output of the
splitter goes to “ANT 1 OUT” and the
second output is connected to IN on the
cable converter box.
If you have a mono VCR, connect L/Mono
to VCR Audio OUT using only one audio
cable.
If you have a S-VHS VCR, use the S-video
connections and remove the video cable.
Do not connect the video cable and the
S-video cable to video1 simultaneously.
When you use a converter box with your
TV there may be features that you can not
program using the remote control, such as
programming your favorite channels and
blocking channels.
English - 19
Page 20
Connections
Connecting a Camcorder
The side panel jacks on your TV make it easy to connect a camcorder to your TV.
You can use your camcorder to view tapes without using a VCR.
Locate the A/V output jacks
on the camcorder. They are
1
usually found on the side or
back of the camcorder.
Connect a set of audio
cables between the AUDIO
2
IN jacks on the TV and the
AUDIO OUT jacks on the
camcorder. If you have
mono camcorder, connect
L(mono) to camcorder audio
out using only one audio
cable.
TV Side PanelCamcorder
Camcorder
Output Jacks
Connect a video cable
between the VIDEO IN (or
3
S-VIDEO IN) jack on the TV
and the VIDEO OUT jack
on the camcorder. The
audio-video cables shown
here are usually included
with a Camcorder. (If not,
check your local electronics
store.) If your camcorder is
stereo, you need to connect
a set of two cables.
English - 20
Page 21
Connecting a DVD Player
The rear panel jacks on your TV make it easy to connect a DVD player to your TV.
Connecting to Y, PB, PR
Connect a set of audio
cables between the
1
COMPONENT (1 or 2)
AUDIO (L, R) IN jacks on the
TV and the AUDIO OUT
jacks on the DVD player.
To enable Component video
viewing, connect a set of
2
video cables between the
COMPONENT (1 or 2)
VIDEO (Y, PB, PR) IN jacks
on the TV and VIDEO
(Y/PB/PRor Y/CB/CR) OUT
jacks on the DVD player.
Note: For an explanation of
Component video, see your
DVD player's owner's
manual.
TV Rear Panel
Incoming
Cable or
Antenna
DVD Player
Connecting to audio and video jacks
Connect a set of audio
cables between the AUDIO
1
IN (1 or 2) jacks on the TV
and the AUDIO OUT jacks
on the DVD player.
Connect a video cable
between the VIDEO IN (1
2
or 2) jack on the TV and the
VIDEO OUT jack on the
DVD player.
TV Rear Panel
Incoming
Cable or
Antenna
DVD Player
English - 21
Page 22
Connections
Connecting a DTV Set-Top Box
Connecting to Y, PB, PR
Connect a set of audio
cables between the
1
COMPONENT (1 or 2)
AUDIO (L, R) IN jacks on the
TV and the AUDIO OUT
jacks on the Set-Top Box.
Connect a set of video
cables between the
2
COMPONENT (1 or 2)
VIDEO (Y, PB, PR) IN jacks
on the TV and VIDEO
(Y/PB/PRor Y/CB/CR) OUT
jacks on the Set-Top Box.
Note: For an explanation of
Component video, see your
Set-Top Box owner's
manual.
Connecting to DVI (Digital Visual Interface)
Connect a set of audio
cables between the DVI
1
AUDIO (L, R) IN jacks on the
TV and the AUDIO OUT
jacks on the Set-Top Box.
TV Rear Panel
Incoming
Cable or
Antenna
DTV Set-Top Box
TV Rear Panel
English - 22
Connect a video cable
between the DVI IN jack on
2
the TV and the DVI OUT
jack on the Set-Top Box.
Incoming
Cable or
Antenna
DTV Set-Top Box
Page 23
Connecting to R, G, B
Connect a set of audio
cables between the PC
1
AUDIO (L, R) IN jacks on the
TV and the AUDIO OUT
jacks on the Set-Top Box.
Connect a video cable
between the PC IN jack on
2
the TV and the R.G.B OUT
jack on the Set-Top Box.
Incoming
Cable or
Antenna
Connecting to HDMI (High Definition Multimedia Interface)
Connect a HDMI cable
between the HDMI IN jack
1
on the TV and the HDMI OUT
jack on the Set-Top Box.
TV Rear Panel
TV Rear Panel
DTV Set-Top Box
NOTE
•Please check if the power of
HDMI source is on, in case that
you fail to select HDMI from the
“Source List” even after you
connected the cable of HDMI
source (DTV Set-Top Box, DVD,
etc.) to TV.
Incoming
Cable or
Antenna
DTV Set-Top Box
English - 23
Page 24
SAMSUNG
Page 25
Operation
Page 26
Operation
Turning the TV On and Off
Press the POWER button on the remote control.
You can also use the POWER button on the front panel.
Viewing the Menus and On-Screen Displays
The on-screen menu system allows you to control the settings of your TV. Access the on-screen menu
system by pressing the MENU button on the remote control. Once the on-screen menu appears, use
the …/†/œ/√/ENTER on your remote control to select menu items and make adjustments.
You can also view the on-screen menu system and make some adjustments using the TV’s side
panel buttons.
Viewing the Menus
Press the MENU button.
1
The main menu is displayed.
There are five menu groups:
“Input”, “Picture”, “Sound”,
“Channel” and “Setup”.
Input
Picture
Sound
Channel
Setup
Source List : TV
Edit Name
Input
MoveEnterExit
√
√
Press the … or † button to
2
select to an item you want in
the menu.
Press the œ, √ or ENTER
button to display, change, or
use the selected items.
Use the ENTER button to
enter items in the menu.
Press the EXIT button to exit.
3
Viewing the Display
Press the INFO button on the
remote control.
The TV displays the current
channel, the status of certain
picture and sound settings and
the current time.
Choose a language for the on-screen menus: English, Spanish or French.
1
2
Selecting the Antenna Input
Press the MENU button.
Press the … or † button to
select “Setup”, then press the
ENTER button.
Press the ENTER button to
select “Language”.
Press the … or † button to
select the appropriate
language, then press ENTER
button.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Setup
Language: English
Time
V-Chip
Caption
Blue Screen: Off
Melody: On
Color Weakness
PC
MoveEnterReturn
Setup
Language: English
Time
V-Chip
Caption
Blue Screen: Off
Melody: On
Color Weakness
PC
MoveEnterReturn
English
Español
Français
√
√
√
√
√
√
√
√
√
You can connect to two different signal sources by choosing the antenna input
(1 or 2).
Press the MENU button.
1
Press the … or † button to select
“Channel”, then press the ENTER button.
Press the ENTER button to select
2
“Antenna”.
Press the … or † button to select “Ant.1”
or “Ant.2”, then press ENTER button.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Antenna: Ant.1
Air/CATV: Air
Auto Program
Add/Delete
Favorite Channels
Name
Fine Tune
Antenna: Ant.1
Air/CATV: Air
Auto Program
Add/Delete
Favorite Channels
Name
Fine Tune
Channel
▼ More
MoveEnterReturn
Channel
Ant.1
Ant.2
▼ More
MoveEnterReturn
√
√
√
√
√
√
√
English - 27
Page 28
Operation
Memorizing the Channels
Your TV can memorize and store all of the available channels for both “off-air” (antenna) and
cable channels. After the available channels are memorized, use the CHand CHbuttons to
scan through the channels. This eliminates the need to change channels by entering the channel
digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing
the channels (automatic) and adding/deleting channels (manual).
Selecting the Video Signal Source
Before your TV can begin memorizing the available channels, you
must specify the type of signal source that is connected to the TV
(i.e., an antenna or a cable system).
Press the MENU button.
1
Press the … or † button to
select “Channel”, then press
the ENTER button.
Press the … or † button to
2
select “Air/CATV”, then
press the ENTER button.
If you are connected to an
antenna, press the … or †
button to select “Air”.
If you connected cable,
press the … or † button to
select the type of cable
system: “STD”, “HRC” or
“IRC”.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Channel
Antenna: Ant.1
Air/CATV: Air
Auto Program
Add/Delete
Favorite Channels
Name
Fine Tune
▼ More
MoveEnterReturn
Channel
Antenna: Ant.1
Air/CATV: Air
Auto Program
Add/Delete
Favorite Channels
Name
Fine Tune
▼ More
MoveEnterReturn
Aire
STD
HRC
IRC
√
√
√
√
√
√
√
English - 28
NOTES
• “STD”, “HRC” and “IRC” identify various types of cable TV
systems. Contact your local cable company to identify the type
of cable system that exists in your particular area. At this point
the signal source has been selected. Proceed to “Storing
Channels in Memory”.
• Subscription cable services require service-specific requirement
for viewing.
Page 29
Storing Channels in Memory (Automatic Method)
First, select the correct signal source (“Air”, “STD”, “HRC” or “IRC”) as
described on the previous page.
Press the MENU button.
1
Press the … or † button to select
“Channel”, then press the ENTER button.
Press the … or † button to select “Auto
2
Program”, then press the ENTER button.
Press the ENTER button to start the auto
program.
The TV begins memorizing all of the
Input
Picture
Sound
Channel
Setup
Antenna: Ant.1
Air/CATV: Air
Auto Program
Add/Delete
Favorite Channels
Name
Fine Tune
Channel
▼ More
MoveEnterReturn
Auto Program
available stations.
Press the ENTER button at any time to
interrupt the memorization process.
Press the EXIT button to exit.
Start
Enter
Return
Adding and Erasing Channels
You can add channels that were not memorized or delete unwanted channels
from memory.
√
√
√
√
√
√
√
Press the MENU button.
1
Press the … or † button to select
“Channel”, then press the ENTER button.
Press the … or † button to select
2
“Add/Delete”, then press the ENTER
button.
Repeatedly pressing the ENTER button will
alternate between add channel and delete
channel.
Antenna: Ant.1
Input
Air/CATV: Air
Auto Program
Picture
Add/Delete
Favorite Channels
Sound
Channel
Name
Fine Tune
Setup
Air 12Not In Memory
Channel
▼ More
MoveEnterReturn
Add/Delete
Press the CHor CHbutton (or
number buttons) to switch to the
appropriate channel, then repeat above.
Change
Add
EnterReturn
Press the EXIT button to exit.
Alternate method
Simply press the ADD/DEL button on the remote control to add or delete channels.
√
√
√
√
√
√
√
English - 29
Page 30
Operation
Changing Channels
You can change channels on your TV by using the CHand CHbuttons, or by direct
selection using the number buttons. You can use the number buttons to tune to any channel (even
one that has been erased or has not been memorized).
Using the Channel Buttons
Press the CHor CHbutton to change channels.
When you press the CHor CHbutton, the TV changes
channels in sequence. You will see all the channels that the TV has
memorized. (The TV must have memorized at least three
channels.) You will not see channels that were either erased or not
memorized.
Using the Number Buttons
Press the number buttons to go directly to a channel.
When you use the number buttons, you can directly select
channels that were either erased or not memorized.
For example, to select channel “27”, press the “2”, then “7”.
The TV will change channels when you press the second number.
To change to single-digit channels (0–9) faster, press the “0”
before the single digit. (For channel “4”, press the “0”, then “4”.)
To select a channel over 100, press the +100 button. (For channel
“122”, press the +100 button, then “2”, then “2”.)
Using the Previous Channel
Press the PRE-CH button.
The TV changes to the last channel you were watching.
English - 30
Page 31
Selecting Your Favorite Channels
You can store your favorite channels for each available input source (such as TV and CATV).
This allows you to quickly and easily find frequently watched channels by pressing the FAV.CH
button on the remote control.
To Store Your Favorite Channels:
Press the MENU button.
1
Press the … or † button to
select “Channel”, then press
the ENTER button.
Input
Picture
Sound
Channel
Setup
Antenna: Ant.1
Air/CATV: Air
Auto Program
Add/Delete
Favorite Channels
Name
Fine Tune
Channel
▼ More
MoveEnterReturn
√
√
√
√
√
√
√
Press the … or † button to
2
select “Favorite Channels”,
then press the ENTER button.
Press the … or † button to
select a channel, then press
the ENTER button.
Press the ENTER button
Input
Picture
Sound
Channel
Setup
Favorite Channels
Air 2 - - - - ✔
Air 3 - - - -
Air 4 - - - -
Air 5 - - - -
Air 6 - - - -
Air 7 - - - -
Air 8 - - - -
▼
Move
Enter
again to deselect the
selected channel.
Press the EXIT button to exit.
To View Your Favorite Channels:
Press the FAV.CH button repeatedly to jump from one favorite
channel to another.
NOTE
• Only memorized channels can be set as Favorite channels.
Return
English - 31
Page 32
Operation
Scanning the Channels
The TV automatically scan all of the channels it has memorized.
Press the MENU button.
1
Press the … or † button to
select “Channel”, then press
the ENTER button.
Press the … or † button to
2
select “Scan”, then press the
ENTER button.
The TV scans all of the
channels memorized.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Channel
Antenna: Ant.1
Air/CATV: Air
Auto Program
Add/Delete
Favorite Channels
Name
Fine Tune
▼ More
MoveEnterReturn
Channel
▲ More
LNA: On
Scan
MoveEnterReturn
Scan
Air 3
Air 4
Return
Enter
Return
√
√
√
√
√
√
√
√
√
English - 32
NOTE
•
When the “ANT 2 IN” mode is selected, the channel scan
function works on the main picture only.
Page 33
Labeling the Channels
Use this feature to assign an easy-to-remember label to any channel (i.e., “CBS”, “ESPN”,
“PBS2”, CNN1”, etc.) A label consists of five fields, where each field is a letter, a number or a
blank. When the INFO button is pressed, the channel label will appear next to the channel
number.
Press the CHor CHbutton to tune to the channel that
1
will be labeled.
NOTE
• If you add or delete
the TV channel, the
labeled channels list
will also be added or
deleted.
Press the MENU button.
2
Press the … or † button to
select “Channel”, then press
the ENTER button.
Press the … or † button to
select “Name”, then press
the ENTER button.
Press the …/†/œ/√ button
3
to move to the channel to be
assigned to a new name,
then press the ENTER button.
Press the … or † button to
select a letter, a number or a
blank. (Results in this
sequence: A...Z, ✽, blank,
0...9, -).
Press the √ button to switch
4
to the next field, which will
be selected.
Select a second letter or digit
pressing … or † button, as
above.
Repeat the process to select
the last two digits.
When you have finished,
press the ENTER button.
To erase the assigned new
name, select “Clear” by
pressing the …/†/œ/√
button, then press the ENTER
button.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Channel
Antenna: Ant.1
Air/CATV: Air
Auto Program
Add/Delete
Favorite Channels
Name
Fine Tune
▼ More
MoveEnterReturn
Name
▲
Air 2 A
Air 3
Air 4
Air 5
Air 6
Air 2 CNN2
Air 3
Air 4
Air 5
Air 6
Clear
▼
----
Clear
----
Clear
----
Clear
----
Clear
▼
MoveAdjustReturn
Name
Clear
----
Clear
----
Clear
----
Clear
----
Clear
▼
MoveEnterReturn
√
√
√
√
√
√
√
Press the EXIT button to exit.
English - 33
Page 34
Operation
Picture Control
You can use the on-screen menus to change the “Contrast”, “Brightness”, “Sharpness”, “Color”
and “Tint” according to personal preference. (Alternatively, you can use one of the automatic
settings. See next page.)
Customizing the Picture
Press the MENU button.
1
Press the … or † button to
select “Picture”, then press
the ENTER button.
Channel
Mode: Standard
Input
Color Tone: Warm1
Size: Wide
Picture
Digital NR: Off
DNIe: On
Sound
My Color Control
Film Mode: Off
PIP
Setup
Picture
MoveEnterReturn
√
√
√
√
√
√
√
√
NOTE
•“Tint” doesn’t operate
in PC, DVI, HDMI or
480p-Component or
higher modes.
Press the ENTER button to
2
select “Mode”.
Press the … or † button to
3
select a particular item, then
press the ENTER button.
Channel
Mode: Standard
Input
Contrast90
Brightness50
Picture
Sharpness50
Color50
Sound
Tint5050
Reset
Setup
▲
Contrast
▼
MoveEnterReturn
Press the œ or √ button to
increase or decrease the
value of a particular item.
Resetting the Picture Settings to the Factory Defaults
You can return to the factory default picture settings.
Press the MENU button to
4
display the “Mode” menu.
Press the … or † button to
select “Reset”, then press the
ENTER button.
The previously adjusted
picture settings will be reset
to the factory defaults.
Channel
Mode: Standard
Input
Contrast90
Brightness50
Picture
Sharpness50
Color50
Sound
Tint5050
Reset
Setup
MoveEnterReturn
Mode
√
90
Mode
√
English - 34
Page 35
Using Automatic Picture Settings
Your TV has automatic picture settings (“Dynamic”, “Standard” and “Cinema”)
that are preset at the factory. You can activate either “Dynamic”, “Standard” or
“Cinema” by pressing the P.MODE button (or by making a selection from the
menu). Or, you can select “Custom” which automatically recalls your
personalized picture settings.
Press the MENU button.
1
Press the … or † button to select
“Picture”, then press the ENTER button.
Press the ENTER button to select “Mode”.
2
Press the ENTER button again to select
3
“Mode”.
Press the … or † button to select a
particular item, then press the ENTER
button.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
Mode
Mode: Standard
Contrast90
Brightness50
Sharpness50
Color50
Tint5050
Reset
Press the P.MODE button on the remote control
repeatedly to select one of the standard picture
settings.
Standard
• Choose “Dynamic” for viewing the TV during the day or when there is a
bright light in the room.
•Choose “Standard” for the standard factory settings.
• Choose “Cinema” when viewing a movie.
English - 35
Page 36
Operation
Sound Control
You can control and customize the sound levels and settings of the TV with the remote control.
Adjusting the Volume
Press the VOL+ or VOL– buttons to increase or decrease the
volume.
Using the MUTE Button
At any time, you can temporarily
cut off the sound.
Press the MUTE button on the
remote control.
The message “Mute” is displayed
and the sound cuts off.
To turn mute off press the MUTE
button again or, press either the
VOL+ or VOL– button.
Mute
English - 36
Customizing the Sound
The sound settings can be adjusted to suit your personal
preference. (Alternatively, you can use one of the automatic
settings. See next page.)
Press the MENU button.
1
Press the … or † button to
select “Sound”, then press
the ENTER button.
Press the … or † button to
2
select “Equalizer”, then
press the ENTER button.
Continued...
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Mode: Standard
Equalizer
SRS TSXT: Off
MTS: Stereo
Auto Volume: Off
Internal Mute: Off
Mode: Standard
Equalizer
SRS TSXT: Off
MTS: Stereo
Auto Volume: Off
Internal Mute: Off
Sound
MoveEnterReturn
Sound
MoveEnterReturn
√
√
√
√
√
√
√
√
√
√
√
√
Page 37
Press the œ or √ button to select a
3
particular item to be changed.
Press the … or † button to increase or
decrease the value of a particular item.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Equalizer
+
R
0
-
L
Balance 100Hz 30 0Hz 1KHz 3KHz 10KHz
MoveAdjustReturn
+
0
-
Using Automatic Sound Settings
Your TV has automatic sound settings (“Standard”, “Music”, “Movie” and “Speech”) that are
preset at the factory. You can activate these sound settings by pressing the S.MODE button (or by
making a selection from the menu), or you can select “Custom”, which automatically recalls your
personalized sound settings.
Press the MENU button.
1
Press the … or † button to select “Sound”,
then press the ENTER button.
Press the ENTER button to select “Mode”.
2
Press the … or † button to select a
particular item, then press the ENTER
button.
Press the EXIT button to exit.
Alternate method
Press the S.MODE button on the remote control
repeatedly to select one of the standard sound
settings.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Sound
Mode: Standard
Equalizer
SRS TSXT: Off
MTS: Stereo
Auto Volume: Off
Internal Mute: Off
MoveEnterReturn
Sound
Mode: Standard
Equalizer
SRS TSXT: Off
MTS: Stereo
Auto Volume: Off
Internal Mute: Off
MoveEnterReturn
Standard
Standard
Music
Movie
Speech
Custom
√
√
√
√
√
√
•Choose “Standard” for the standard factory settings.
• Choose “Music” when watching music videos or concerts.
•Choose “Movie” when watching movies.
• Choose “Speech” when watching a show that is mostly dialogue (i.e., news).
•Choose “Custom” to recall your personalized settings.
English - 37
Page 38
Operation
Setting the Clock
Setting the clock is necessary in order to use the various timer features of the TV. Also, you can
check the time while watching the TV. (Just press the INFO button.)
Press the MENU button.
1
Press the … or † button to
select “Setup”, then press the
ENTER button.
Press the … or † button to
select “Time”, then press the
ENTER button.
Press the ENTER button to
2
select “Clock Set”.
Press the œ or √ button to
3
move to “Hour”, “Min” or
“am/pm”.
Set the clock you want by
pressing the … or † button,
then press the ENTER button.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Setup
Language: English
Time
V-Chip
Caption
Blue Screen: Off
Melody: On
Color Weakness
PC
MoveEnterReturn
Time
Clock Set- - : - - am
Sleep TimerOff
On TimerOff
Off TimerOff
MoveEnterReturn
Clock Set
Hour Min am/pm
▲
1200am
▼
MoveAdjustReturn
√
√
√
√
√
√
√
√
√
√
√
√
English - 38
NOTE
• The current time will appear every time you press the INFO
button.
Absent Power Off
When you set the timer “On”, your television will eventually be turned off, if you do not operate any
controls during the 3 hours after the TV is turned on by timer. This function is available in only the
timer “On” mode and will prevent a leakage accident or overheating, caused by your TV left on for
a long time due to the timer “On” (when you are away on holiday, for example).
Page 39
Setting the Timers
This TV can be set to turn on or off automatically at specific times that you
choose. Before using the timers, you must set the TV’s clock, as described
previously.
Setting the On/Off Timer
Press the MENU button.
1
Press the … or † button to select “Setup”,
then press the ENTER button.
Input
Picture
Sound
Channel
Setup
Language: English
Time
V-Chip
Caption
Blue Screen: Off
Melody: On
Color Weakness
PC
Setup
MoveEnterReturn
√
√
√
√
√
√
√
√
Press the … or † button to select “Time”,
2
then press the ENTER button.
Press the … or † button to select “On
Timer”, then press the ENTER button.
Press the … or † button to adjust “Hour”,
3
then press the √ button to move to the
next step.
Set other items using the same method as
above.
When finished, press the MENU button to
return.
Press the … or † button to select “Off
4
Timer”, then press the ENTER button.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Time
Clock Set10 : 30 am
Sleep TimerOff
On TimerOff
Off TimerOff
MoveEnterReturn
On Timer
Hour Min am/pm
▲
1200am
▼
ChVol.
0310No
Clock Set10 : 30 am
Sleep TimerOff
On Timer06 : 30 am
Off TimerOff
Activation
MoveAdjustReturn
Time
MoveEnterReturn
√
√
√
√
√
√
√
√
Press the … or † button to adjust “Hour”,
5
then press the √ button to move to the
next step.
Set other items using the same method as
above.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Off Timer
Hour Min am/pm
▲
1200am
▼
MoveAdjustReturn
Activation
No
English - 39
Page 40
Operation
Setting the Sleep Timer
The sleep timer automatically shuts off the TV after a preset time (from 30 to 180 minutes).
Press the MENU button.
1
Press the … or † button to
select “Setup”, then press the
ENTER button.
Press the … or † button to
2
select “Time”, then press the
ENTER button.
Press the … or † button to
select “Sleep Timer”, then
press the ENTER button.
Press the … or † button to
3
select the preset time you
want, then press the ENTER
button.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Setup
Language: English
Time
V-Chip
Caption
Blue Screen: Off
Melody: On
Color Weakness
PC
MoveEnterReturn
Time
Clock Set10 : 30 am
Sleep TimerOff
On Timer06 : 30 am
Off Timer11 : 30 pm
MoveEnterReturn
Time
Clock Set10 : 30 am
Sleep TimerOff
On Timer06 : 30am
Off Timer11 : 30pm
MoveEnterReturn
Off
120
150
180
30
60
90
√
√
√
√
√
√
√
√
√
√
√
√
English - 40
Alternate method
Press the SLEEP button on the
remote control repeatedly until the
appropriate time interval appears
(any of the preset values from “30
Min.” to “180 Min.”).
30 Min.
NOTE
• If no signal is received for 15 minutes, the TV will be
automatically turned off.
Page 41
Viewing an External Signal Source
Use the remote control to switch between viewing signals from connected equipment, such as
VCR, DVD, Set-Top Box and the TV source (broadcast or cable).
Setting the Signal Source
Press the MENU button.
1
Press the ENTER button to
select “Input”.
Input
Picture
Sound
Channel
Setup
Source List : TV
Edit Name
Input
MoveEnterReturn
√
√
Press the ENTER button to
2
select “Source List”.
Press the … or † button to
select a signal source, then
press the ENTER button.
Press the SOURCE button on the
remote control repeatedly to
select an external signal source.
AV1
NOTE
• When you connect equipment to the TV, you can choose
between the following sets of jacks: “AV1”, “AV2”, “S-Video1”,
“S-Video2”, “Component1”, “Component2”, “PC”, “DVI” or
“HDMI” on the TV’s rear panel, and “AV3” or “S-Video3” on
the TV’s side panel.
English - 41
Page 42
Operation
Assigning Names to External Input Mode
This feature enables you to name the input source you have connected.
Press the MENU button.
1
Press the ENTER button to
select “Input”.
Press the … or † button to
2
select “Edit Name”, then
press the ENTER button.
Press the … or † button to
3
select a signal source, then
press the ENTER button.
Press the … or † button to
select an external device,
then press the ENTER button.
You can freeze the picture when watching a television programme simply by pressing the STILL
button. To return to normal viewing, press it again.
NOTE
• In the PIP mode, the main and sub pictures are stilled at the
same time.
Remote Control VCR/DVD Buttons
Slide the cover of the remote control up to access buttons that can control the tape functions of a
connected VCR or DVD, including Rewind, Stop, Play/Pause and Fast Forward.
Slide the cover of your remote control unit for access to the tape
function controls. Press the appropriate buttons to control your
VCR or DVD.
English - 43
Page 44
SAMSUNG
Page 45
Special Features
Page 46
Special Features
Customizing Your Remote Control
Your TV comes equipped with a universal remote control. In addition to controlling the TV, the universal
remote control can also operate a VCR, Cable box, DVD, and some Samsung Set-top boxes (even if
your VCR, Cable box and DVD are made by manufacturers other than Samsung).
NOTE
• The remote control might not be compatible with all DVD Players, VCRs, Cable boxes, and
Set-Top Boxes.
Setting Up Your Remote Control to Operate Your VCR (Cable box or
DVD player)
Turn off your VCR (Cable box or DVD player).
1
Press the MODE button to switch the remote control to the VCR
2
(CABLE or DVD) mode.
The remote control has five modes: TV, STB, VCR, CABLE, and
DVD.
On your Samsung remote control, press the SET button.
3
Enter 3 digits of the VCR (Cable box or DVD player) code listed
4
on next page for your brand of VCR (Cable box or DVD
player).
Make sure you enter 3 digits of the code, even if the first digit is
a “0”. (If more than one code listed, try the first one.)
Press the POWER button. Your VCR (Cable box or DVD player)
5
should turn on. If your VCR (Cable box or DVD player) turns on,
your remote control is now set correctly.
If your VCR (Cable box or DVD player) does not turn on, repeat
steps 2, 3, and 4, but try one of the other codes listed for the
brand of your particular VCR (Cable box or DVD player).
Once your remote control is set up, press the MODE button any
6
time you want to use the remote to operate your VCR (Cable
box or DVD player).
NOTES
• When your remote is in the TV mode, the VCR (or DVD player)
control buttons (REW, STOP, PLAY/PAUSE, and FF) will still operate
your VCR (or DVD player).
• When your remote control is in the STB, VCR, CABLE, or DVD
mode, the volume buttons still control your TV’s volume.
English - 46
Page 47
Remote Control Codes
VCR Codes
Cable Box Codes
DVD Codes
English - 47
Page 48
Special Features
Fine Tuning Channels
The Fine Tuning function lets you manually adjust the TV’s tuner if you have difficulty tuning
channels.
Using the number buttons on the remote control, select the
1
channel you want to fine tune.
Press the MENU button.
2
Press the … or † button to
select “Channel”, then press
the ENTER button.
Press the … or † button to
3
select “Fine Tune”, then
press the ENTER button.
Press the œ or √ button to
4
adjust the fine tuning.
To store the fine tuning
setting in the TV’s memory,
press the ENTER button.
The symbol “*” is displayed.
To reset the fine tuning to
“0”, select “Reset” by
pressing the … or † button,
then press the ENTER button.
Channel
Antenna: Ant.1
Input
Air/CATV: Air
Auto Program
Picture
Add/Delete
Favorite Channels
Sound
Channel
Channel
Name
Fine Tune
▼ More
Setup
Input
Picture
Sound
Setup
Air 12
MoveSaveReturn
Air 12
MoveEnterReturn
MoveEnterReturn
Channel
Antenna: Ant.1
Air/CATV: Air
Auto Program
Add/Delete
Favorite Channels
Name
Fine Tune
▼ More
MoveEnterReturn
Fine Tune
Reset
Adjust
Fine Tune
*
Reset
√
√
√
√
√
√
√
√
√
√
√
√
√
√
3
3
English - 48
Press the EXIT button to exit.
Fine Tune
Air 12
0
Reset
MoveEnterReturn
Page 49
LNA (Low Noise Amplifier)
When a weak broadcast signal causes unclear noisy picture the “LNA” feature improves the
picture quality by setting to “On”. If you experience noise on a certain channel, set the “LNA” to
“On” or “Off” for this channel, to obtain the optimum picture.
Press the MENU button.
1
Press the … or † button to
select “Channel”, then press
the ENTER button.
Press the … or † button to
2
select “LNA”, then press the
ENTER button.
Press the … or † button to
3
select “On” or “Off”, then
press the ENTER button.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Channel
Antenna: Ant.1
Air/CATV: Air
Auto Program
Add/Delete
Favorite Channels
Name
Fine Tune
▼ More
MoveEnterReturn
Channel
▲ More
LNA: Off
Scan
MoveEnterReturn
Channel
▲ More
LNA: Off
Scan
MoveEnterReturn
√
√
√
√
√
√
√
√
√
Off
On
NOTE
• This function works in “ANT 1 IN” mode only (not available in
“ANT 2 IN” mode).
English - 49
Page 50
Special Features
Selecting the Color Tone
Press the MENU button.
1
Press the … or † button to
select “Picture”, then press
the ENTER button.
Press the … or † button to
2
select “Color Tone”, then
press the ENTER button.
Press the … or † button to
3
select “Cool2”, “Cool1”,
“Normal”, “Warm1” or
“Warm2”, then press the
ENTER button.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
Cool2
Cool1
Normal
Warm1
Warm2
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
English - 50
NOTE
• Not available in the “Cinema” picture mode.
Page 51
Changing the Picture Size
You can select the picture size which best corresponds to your viewing requirements.
Press the MENU button.
1
Press the … or † button to
select “Picture”, then press
the ENTER button.
Press the … or † button to
select “Size”, then press the
ENTER button.
Press the œ or √ button to
2
select the screen format you
want, then press the ENTER
button.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
Wide Panorama Zoom1 Zoom24:3
Picture
MoveEnterReturn
Size
MoveEnterReturn
Alternate method
Press the P.SIZE button on the remote control repeatedly to select
one of the picture size settings.
•“Wide”: Sets the picture to 16:9 wide mode.
• “Panorama”: Use this mode for the wide aspect ratio of a
panoramic picture.
• “Zoom1”: Magnifies the size of the picture on screen. You can
also move the picture on screen using the scroll function. Press
… or † button to scroll the picture.
the
• “Zoom2”: Magnifies the size of the picture more than
“Zoom1”. You can also move the picture on screen using the
scroll function. Press the … or † button to scroll the picture.
• “4:3”: Sets the picture to 4:3 normal mode. This is a standard
TV screen size.
√
√
√
√
√
√
√
√
NOTES
•You can select only Wide, 4:3 screen size in the Component(480p, 720p, 1080i) Mode.
•With PIP On, the screen automatically becomes wide in the Antenna, AV (1~3), S-Video (1~3)
or Component (480i) mode. With PIP Off, it returns to original screen size.
• The picture size can’t be changed when the “PIP” is active in the TV or AV mode.
English - 51
Page 52
Special Features
Digital Noise Reduction
If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction
feature to help reduce any static and ghosting that may appear on the screen.
Press the MENU button.
1
Press the … or † button to
select “Picture”, then press
the ENTER button.
Press the … or † button to
2
select “Digital NR”, then
press the ENTER button.
Press the … or † button to
3
select “Off” or “On”, then
press the ENTER button.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
Off
On
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
English - 52
Page 53
TM
DNIe
(Digital Natural Image engine)
This feature brings you more detailed image with 3D noise reduction, detail enhancement,
contrast enhancement and white enhancement. New image compensation Algorithm presents
brighter, clearer, much detailed image. DNIeTMtechnology will fit every signals into your eyes.
Press the MENU button.
1
Press the … or † button to
select “Picture”, then press
the ENTER button.
Press the … or † button to
2
select “DNIe”, then press the
ENTER button.
Press the … or † button to
3
select “Off”, “Demo” or
“On”, then press the ENTER
button.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
Off
Demo
On
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
Alternate method
Press the DNIe button on the remote control repeatedly to select
one of the settings.
• On: Switches on the DNIe mode.
•Off: Switches off the DNIe mode.
• Demo: The screen before applying
DNIe appears on the right and the
screen after applying DNIe appears
on the left.
DNIe Demo
DNIe OnDNIe Off
English - 53
Page 54
Special Features
Setting the My Color Control Mode
My Color Control allows users to adjust colors to according to their preferences, by adjusting
skin, sky, and grass tones using the predefined settings (“Blue”, “Green”, “Pink”, “Standard”,
“Custom”) without affecting other colors on the screen.
Using the Easy Control Menu
Press the MENU button.
1
Press the … or † button to
select “Picture”, then press
the ENTER button.
Channel
Mode: Standard
Input
Color Tone: Warm1
Size: Wide
Picture
Digital NR: Off
DNIe: On
Sound
My Color Control
Film Mode: Off
PIP
Setup
Picture
MoveEnterReturn
√
√
√
√
√
√
√
√
NOTE
• Changing the settings
in the “Detail Control”
menu (see next page)
will automatically set
the My Color Control
mode to “Custom”.
Press the … or † button to
2
select “My Color Control”,
then press the ENTER button.
Press the ENTER button to
3
select “Easy Control”.
Press the œ or √ button to
select one of the picture
settings you want.
The original picture (before
adjustment) is shown
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
Easy Control: Blue
Detail Control
Picture
MoveEnterReturn
My Color Control
MoveEnterReturn
on the left side, while the
selected mode is shown
on the right side.
Press the ENTER button to
accept the selected mode.
Press the EXIT button to exit.
OriginalBlue
Easy Control
BlueGreenPink√
MoveReturn
Enter
• “Blue”: Emphasizing Clear Blues. Feel the clear sun shine on
the blue Mediterranean sea.
select “Picture”, then press
the ENTER button.
Press the … or † button to
select “My Color Control”,
then press the ENTER button.
Input
Picture
Sound
Channel
Setup
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
√
√
√
√
√
√
√
√
Press the … or † button to
2
select “Detail Control”, then
press the ENTER button.
Press the … or † button to
3
select one of the My Color
Control color you want, then
press the ENTER button.
There are three colors:
“Pink”, “Green” and “Blue”.
Press the œ or √ button to
adjust the value of a color
selected.
Changing the adjustment
value will refresh the
adjusted screen.
My Color Control
Easy Control: Blue
Input
Detail Control
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
▲
Pink
▼
MoveReturn
MoveEnterReturn
Detail Control
Pink50
Green50
Blue100
Reset
MoveEnterReturn
OriginalAdjusted
Detail Control
Adjust
√
√
50
Resetting the My Color Control Colors to the Factory Defaults
You can return to the factory default settings for My Color Control
colors.
Press the MENU button to
4
display the “Detail Control”
menu.
Press the
… or † button to
select “Reset”, then press the
ENTER button.
The previously adjusted My
Color Control Colors will be
reset to the factory defaults.
Input
Picture
Sound
Channel
Setup
Detail Control
Pink50
Green50
Blue50
Reset
MoveEnterReturn
English - 55
Page 56
Special Features
Setting the Film Mode
You can automatically sense and process film signals from all sources and adjust the picture for
optimum quality.
Press the MENU button.
1
Press the … or † button to
select “Picture”, then press
the ENTER button.
Press the … or † button to
2
select “Film Mode”, then
press the ENTER button.
Press the … or † button to
3
select “Off” or “On”, then
press the ENTER button.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
Off
On
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
English - 56
NOTE
• Film mode is supported in 480i only.
Page 57
Viewing Picture-In-Picture
One of the most best features of your TV is the Picture-In-Picture (PIP) feature. The advanced PIP
system allows you to watch two different pictures at once, even if you don’t have a VCR
connected to your TV.
Activating the PIP
Press the MENU button.
1
Press the … or † button to
select “Picture”, then press
the ENTER button.
Input
Picture
Sound
Channel
Setup
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
Picture
MoveEnterReturn
√
√
√
√
√
√
√
√
Press the … or † button to
2
select “PIP”, then press the
ENTER button.
Press the ENTER button to
3
select “PIP”.
Press the … or † button to
select “On”, then press the
ENTER button.
The sub picture appears in
the corner of the screen.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
PIP:On
Source: TV
Swap
Size
Position
Channel: Air 11
Select Sound: Main
Picture
MoveEnterReturn
PIP
Off
On
MoveEnterReturn
Press the EXIT button to exit.
Alternate method
Press the PIP button on the remote control repeatedly to activate or
deactivate the PIP.
√
√
√
√
√
√
√
√
NOTES
• This feature doesn’t function when the “V-Chip” or “Caption” is active.
• This feature doesn’t operate in the HDMI mode.
• If you turn the TV off while watching and turn it on again, then the mode will return to normal
video.
English - 57
Page 58
Special Features
Selecting an External Source
You can use PIP to view a signal from an external source, such as a VCR.
Press the MENU button.
1
Press the … or † button to
select “Picture”, then press
the ENTER button.
Press the … or † button to
2
select “PIP”, then press the
ENTER button.
Press the … or † button to
3
select “Source”, then press
the ENTER button.
If you have not connected
any equipment to the TV’s
input jacks, the signal from
these inputs will not appear.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
PIP
PIP: On
Source: TV
Swap
Size
Position
Channel: Air 11
Select Sound: Main
MoveEnterReturn
TV
AV1
AV2
AV3
S-Video1
S-Video2
S-Video3
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
English - 58
Press the … or † button to
select an external signal,
then press the ENTER button.
Press the EXIT button to exit.
NOTES
• The sub picture doesn’t support “ANT 2 IN”, “Component1”, “Component2”, “PC”, “DVI” and
“HDMI”.
• For more information about external signals, see “Viewing an External Signal Source” (See
page 41). If you select “TV”, the sub picture is the same as the main picture.
Page 59
Swapping the Sub Picture and Main Picture
Press the MENU button.
1
Press the … or † button to
select “Picture”, then press
the ENTER button.
Press the … or † button to
2
select “PIP”, then press the
ENTER button.
Press the … or † button to
3
select “Swap”, then press
the ENTER button.
The sub picture appears in
the main picture, and vice
versa.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
PIP
PIP: On
Source: TV
Swap
Size
Position
Channel: Air 11
Select Sound: Main
MoveEnterReturn
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
NOTE
• The swapping doesn’t support “ANT 2 IN”, “Component1”, “Component2”, “PC”, “DVI” and
“HDMI”.
English - 59
Page 60
Special Features
Changing the Size of the Sub Picture
Press the MENU button.
1
Press the … or † button to
select “Picture”, then press
the ENTER button.
Press the … or † button to
2
select “PIP”, then press the
ENTER button.
Press the … or † button to
3
select “Size”, then press the
ENTER button.
Press the … or † button to
select a size you want, then
press the ENTER button.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
PIP
PIP: On
Source: TV
Swap
Size
Position
Channel: Air 11
Select Sound: Main
MoveEnterReturn
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
English - 60
Press the EXIT button to exit.
Alternate method
Press the SIZE button on the remote control repeatedly to select
one of the settings.
Page 61
Changing the Location of the Sub Picture
Press the MENU button.
1
Press the … or † button to
select “Picture”, then press
the ENTER button.
Press the … or † button to
2
select “PIP”, then press the
ENTER button.
Press the … or † button to
3
select “Position”, then press
the ENTER button.
Press the … or † button to
select a position you want,
then press the ENTER button.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
PIP
PIP: On
Source: TV
Swap
Size
Position
Channel: Air 11
Select Sound: Main
MoveEnterReturn
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
Press the EXIT button to exit.
English - 61
Page 62
Special Features
Changing the Channel of the Sub Picture
After you set the signal source (antenna or cable) of sub picture, it is easy to change channels.
Press the MENU button.
1
Press the … or † button to
select “Picture”, then press
the ENTER button.
Press the … or † button to
2
select “PIP”, then press the
ENTER button.
Press the … or † button to
3
select “Channel”, then press
the ENTER button.
Press the … or † button to
select a channel you want,
then press the ENTER button.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
PIP
PIP: On
Source: TV
Swap
Size
Position
Channel: Air 11
Select Sound: Main
MoveEnterReturn
Air 11
▲
▼
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
English - 62
Press the EXIT button to exit.
Alternate method
Press the CHor CHbutton on the remote control to change
channels of sub picture during PIP on.
NOTE
• The channels of sub picture are not available when antenna is set to “ANT 2 IN”. It links to
“ANT 1 IN”.
Page 63
Selecting the Sound Source
You can use this feature to hear sound from the main or sub picture.
Press the MENU button.
1
Press the … or † button to
select “Picture”, then press
the ENTER button.
Press the … or † button to
2
select “PIP”, then press the
ENTER button.
Press the … or † button to
3
select “Select Sound”, then
press the ENTER button.
Press the … or † button to
select “Main” or “Sub”,
then press the ENTER button.
“Main” is for the main TV
picture audio, and “Sub” is
for the sub picture (PIP)
audio.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
Picture
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: Off
DNIe: On
My Color Control
Film Mode: Off
PIP
MoveEnterReturn
PIP
PIP: On
Source: TV
Swap
Size
Position
Channel: Air 11
Select Sound: Main
MoveEnterReturn
Main
Sub
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
Press the EXIT button to exit.
English - 63
Page 64
Special Features
Setting the SRS TSXT
TruSurround XT is a patented SRS technology that solves the problem of playing 5.1 multichannel
content over two speakers. Trusurround delivers a compelling, virtual surround sound experience
through any two-speaker playback system, including internal television speakers. It is fully
compatible with all multichannel formats.
Press the MENU button.
1
Press the … or † button to
select “Sound”, then press
the ENTER button.
Press the … or † button to
2
select “SRS TSXT”, then
press the ENTER button.
Press the … or † button to
3
select “Off”, “3D Mono” or
“Stereo”, then press the
ENTER button.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Sound
Mode: Standard
Equalizer
SRS TSXT: Off
MTS: Stereo
Auto Volume: Off
Internal Mute: Off
MoveEnterReturn
Sound
Mode: Standard
Equalizer
SRS TSXT: Off
MTS: Stereo
Auto Volume: Off
Internal Mute: Off
MoveEnterReturn
Sound
Mode: Standard
Equalizer
SRS TSXT: Off
MTS: Stereo
Auto Volume: Off
Internal Mute: Off
MoveEnterReturn
Off
3D Mono
Stereo
√
√
√
√
√
√
√
√
√
√
√
√
English - 64
Alternate method
Press the SRS button on the remote control repeatedly to select one
of the settings.
Page 65
Choosing a Multi-Channel Sound (MTS) track
Depending on the particular program being broadcast, you can listen to “Mono”, “Stereo” or
“SAP (Separate Audio Program)”. “SAP” audio is usually a foreign-language translation.
Sometimes “SAP” has unrelated information like news or weather.
Press the MENU button.
1
Press the … or † button to
select “Sound”, then press
the ENTER button.
Press the … or † button to
2
select “MTS”, then press the
ENTER button.
Press the … or † button to
3
select “Mono”, “Stereo” or
“SAP”, then press the ENTER
button.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Sound
Mode: Standard
Equalizer
SRS TSXT: Off
MTS: Stereo
Auto Volume: Off
Internal Mute: Off
MoveEnterReturn
Sound
Mode: Standard
Equalizer
SRS TSXT: Off
MTS: Stereo
Auto Volume: Off
Internal Mute: Off
MoveEnterReturn
Sound
Mode: Standard
Equalizer
SRS TSXT: Off
MTS: Stereo
Auto Volume: Off
Internal Mute: Off
MoveEnterReturn
Mono
Stereo
SAP
√
√
√
√
√
√
√
√
√
√
√
√
Alternate method
Press the MTS button on the remote control repeatedly to select
one of the settings.
• Choose “Mono” for channels that are broadcasting in mono, or
if you are having difficulty receiving a stereo signal.
• Choose “Stereo” for channels that are broadcasting in stereo.
• Choose “SAP” to listen to the Separate Audio Program, which
is usually a foreign-language translation.
English - 65
Page 66
Special Features
Auto Volume
Each broadcasting station has its own signal conditions, and it is inconvenient to adjust the
volume every time the channel is changed. “Auto Volume” automatically adjusts the volume of the
desired channel by lowering the sound output when the modulation signal is high or by raising
the sound output when the modulation signal is low.
Press the MENU button.
1
Press the … or † button to
select “Sound”, then press
the ENTER button.
Press the … or † button to
2
select “Auto Volume”, then
press the ENTER button.
Press the … or † button to
3
select “Off” or “On”, then
press the ENTER button.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Sound
Mode: Standard
Equalizer
SRS TSXT: Off
MTS: Stereo
Auto Volume: Off
Internal Mute: Off
MoveEnterReturn
Sound
Mode: Standard
Equalizer
SRS TSXT: Off
MTS: Stereo
Auto Volume: Off
Internal Mute: Off
MoveEnterReturn
Sound
Mode: Standard
Equalizer
SRS TSXT: Off
MTS: Stereo
Auto Volume: Off
Internal Mute: Off
MoveEnterReturn
Off
On
√
√
√
√
√
√
√
√
√
√
√
√
English - 66
Page 67
Enjoying the Sound of External Speakers
When using external device such as Home Theater Systems, external speaker, or external Audio
Amplifier set “Internal Mute” to “On” to produce sound which is consistent with what the picture
shows.
Press the MENU button.
1
Press the … or † button to
select “Sound”, then press
the ENTER button.
Press the … or † button to
2
select “Internal Mute”, then
press the ENTER button.
Press the … or † button to
3
select “Off” or “On”, then
press the ENTER button.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Sound
Mode: Standard
Equalizer
SRS TSXT: Off
MTS: Stereo
Auto Volume: Off
Internal Mute: Off
MoveEnterReturn
Sound
Mode: Standard
Equalizer
SRS TSXT: Off
MTS: Stereo
Auto Volume: Off
Internal Mute: Off
MoveEnterReturn
Sound
Mode: Standard
Equalizer
SRS TSXT: Off
MTS: Stereo
Auto Volume: Off
Internal Mute: Off
MoveEnterReturn
Off
On
√
√
√
√
√
√
√
√
√
√
√
√
English - 67
Page 68
Special Features
0 9
0 9
Using the V-Chip
Access to channels and programs is controlled by a password (i.e., a 4-digit secret code that is
defined by the user). The on-screen menu will instruct you to assign a password (you can change
it later, if necessary).
NOTE
• The V-Chip doesn’t function when the PIP is active.
How to Change Your Password
Press the MENU button.
1
Press the … or † button to
select “Setup”, then press the
ENTER button.
Press the … or † button to
select “V-Chip”, then press
the ENTER button.
Channel
Language: English
Input
Time
V-Chip
Picture
Caption
Blue Screen: Off
Sound
Melody: On
Color Weakness
PC
Setup
MoveEnterReturn
Setup
√
√
√
√
√
√
√
√
English - 68
NOTE
• If you forget the pin
number, press the
remote control buttons
in the following
sequence, which resets
the pin to 0-0-0-0:
POWER (Off), MUTE,
8, 2, 4, POWER (On).
Press the number buttons to
2
enter your current 4-digit pin
number.
(The default pin number for
a new TV set is “0000”.)
The “V-Chip” menu is
displayed.
Press the … or † button to
3
select “Change PIN”, then
press the ENTER button.
Press the number buttons to
4
enter your new 4-digit pin
number.
Re-enter your new pin
number to confirm.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
<USA>
Input
Picture
Sound
Channel
Setup
<Canada>
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
V-Chip
Enter PIN
*
Enter PINReturn
V-Chip
V-Chip Lock: Off
TV Parental Guidelines
MPAA Rating
Change PIN
MoveEnterReturn
V-Chip
V-Chip Lock: Off
TV Parental Guidelines
MPAA Rating
Canadian English
Canadian French
Change PIN
MoveEnterReturn
Change PIN
Enter New PIN
*
Enter PINReturn
√
√
√
√
√
√
√
√
√
√
Page 69
How to Enable/Disable the Rating Controls
0 9
Press the MENU button.
1
Press the … or † button to
select “Setup”, then press the
ENTER button.
Press the … or † button to
select “V-Chip”, then press
the ENTER button.
Press the number buttons to
2
enter your current 4-digit pin
number.
(The default pin number for
a new TV set is “0000”.)
The “V-Chip” menu is
displayed.
Press the ENTER button to
3
select “V-Chip Lock”.
Press the … or † button to
select “On”, then press the
ENTER button.
Press the EXIT button to exit.
Picture
Sound
Channel
Setup
Picture
Sound
Channel
Setup
<USA>
Picture
Sound
Channel
Setup
Language: English
Input
Time
V-Chip
Caption
Blue Screen: Off
Melody: On
Color Weakness
PC
MoveEnterReturn
Input
Enter PIN
*
Enter PINReturn
V-Chip Lock: Off
Input
TV Parental Guidelines
MPAA Rating
Change PIN
MoveEnterReturn
Setup
V-Chip
V-Chip
√
√
√
√
√
√
√
√
Off
On
<Canada>
Input
Picture
Sound
Channel
Setup
V-Chip
V-Chip Lock: Off
TV Parental Guidelines
MPAA Rating
Canadian English
Canadian French
Change PIN
MoveEnterReturn
Off
On
English - 69
Page 70
Special Features
0 9
How to Set up Restrictions Using the “TV Parental Guidelines”
The parental restrictions can be set up using either of two methods: The “TV Parental Guidelines”
or “MPAA Rating”.
Press the MENU button.
1
Press the … or † button to
select “Setup”, then press the
ENTER button.
Press the … or † button to
select “V-Chip”, then press
the ENTER button.
Press the number buttons to
2
enter your current 4-digit pin
number.
(The default pin number for
a new TV set is “0000”.)
The “V-Chip” menu is
displayed.
Press the … or † button to
3
select “TV Parental
Guidelines”, then press the
ENTER button.
Picture
Sound
Channel
Setup
Picture
Sound
Channel
Setup
<USA>
Picture
Sound
Channel
Setup
Language: English
Input
Time
V-Chip
Caption
Blue Screen: Off
Melody: On
Color Weakness
PC
MoveEnterReturn
Input
Enter PIN
*
Enter PINReturn
V-Chip Lock: On
Input
TV Parental Guidelines
MPAA Rating
Change PIN
MoveEnterReturn
Setup
V-Chip
V-Chip
√
√
√
√
√
√
√
√
√
√
√
√
<Canada>
V-Chip
Input
Picture
Sound
Channel
Setup
V-Chip Lock: On
TV Parental Guidelines
MPAA Rating
Canadian English
Canadian French
Change PIN
MoveEnterReturn
√
√
√
√
√
√
English - 70
Page 71
You can independently lock the TV
4
ratings. The locked TV (FCC) ratings are
indicated by the symbol “ ”.
Press the …/†/œ/√ buttons and the
ENTER button to activate the appropriate
restrictions for TV (FCC) rating system.
Input
Picture
Sound
Channel
Setup
TV Parental Guidelines
ALL FV V S L D
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
MoveEnterReturn
TV-Y: Young children
TV-Y7 : Children 7 and over
TV-G: General audience
TV-PG : Parent Guidance
TV-14 : Viewers 14 and over
TV-MA : Mature Audience
Press the EXIT button to exit.
NOTES
• These categories consist of two separate groups: “TV-Y” and “TV-Y7” (young
children through age 7), and “TV-G” through “TV-MA” (everybody else).
• The restrictions for these two groups work independently: If a household
includes very young children as well as young adults, the TV parental
guidelines must be set up separately for each age group. (See page 73.)
English - 71
Page 72
Special Features
0 9
How to Set up Restrictions Using the “MPAA Rating”
The Movie rating system uses the “MPAA” (Motion Picture Association of America) system, and its
main application is for movies.
When the rating control is on, the TV will automatically block any programs that are coded with
objectionable ratings (either “MPAA Rating” or “TV Parental Guidelines”).
Press the MENU button.
1
Press the … or † button to
select “Setup”, then press the
ENTER button.
Press the … or † button to
select “V-Chip”, then press
the ENTER button.
Press the number buttons to
2
enter your current 4-digit pin
number.
(The default pin number for
a new TV set is “0000”.)
The “V-Chip” menu is
displayed.
Press the … or † button to
3
select “MPAA Rating”, then
press the ENTER button.
Picture
Sound
Channel
Setup
Picture
Sound
Channel
Setup
<USA>
Picture
Sound
Channel
Setup
Language: English
Input
Time
V-Chip
Caption
Blue Screen: Off
Melody: On
Color Weakness
PC
MoveEnterReturn
Input
Enter PIN
*
Enter PINReturn
V-Chip Lock: On
Input
TV Parental Guidelines
MPAA Rating
Change PIN
MoveEnterReturn
Setup
V-Chip
V-Chip
√
√
√
√
√
√
√
√
√
√
√
√
<Canada>
V-Chip
You can independently lock
4
the movie ratings. The locked
movie ratings are indicated
by the symbol
“”.
Press the …/†/ENTER
buttons to activate the
appropriate restrictions for
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
V-Chip Lock: On
TV Parental Guidelines
MPAA Rating
Canadian English
Canadian French
Change PIN
MoveEnterReturn
MPAA Rating
Block
G
PG
PG-13
R
NC-17
X
NR
MoveEnterReturn
√
√
√
√
√
√
movie rating system.
English - 72
Press the EXIT button.
Page 73
Important Notes About Parental Locks
Explanation of the MPAA and TV (FCC) Rating Systems:
TV (FCC) Age-Based Ratings
TV-MA
Mature audiences only. This program may
contain mature themes, profane language,
graphic violence and explicit sexual content.
TV-14
Parents strongly cautioned. This program may
contain sophisticated themes, sexual content,
strong language and more intense violence.
TV-PG
Parental guidance suggested. The program
may contain infrequent coarse language,
limited violence, some suggestive sexual
dialog and situations.
TV (FCC) Content Category
VViolence.
SSexual content.
LOffensive language.
DDialog sexual innuendo.
FVFantasy or cartoon violence.
MPAA Rating System (Movies)
GGeneral audience. No restriction.
PGChildren under 13 should be
PG-13Parental guidance suggested. Children
RRestricted. Viewers should be 17 or older.
NC-17Not classified. Viewers should be 17 or
XAdults only.
NRNot rated.
TV-G
General audience. It contains little or no
violence, no strong language, and little or no
sexual dialog or situations.
TV-Y7
Directed to older children. Themes and
elements in this program may include mild
physical or comedic violence, or may frighten
children under the age of seven.
TV-Y
All children. The themes and elements in this
program are specifically designed for a very
young audience, including children from ages
two – six.
accompanied by an adult.
under 13 should be accompanied by an
adult.
older.
• TV (FCC) ratings : The particular rating that you have selected will be locked (and indicated as
a red “L” on a blue background). Also, all of the age-based ratings will be locked within the
particular group (i.e., “group 1” or “group 2”). Suppose that the TV-G rating and all of its
contents (V, S, L, and D) are locked. In that case, more restrictive ratings (TV-PG, TV-14, and
TV-MA) and all of their contents (V, S, L, and D) are automatically locked as well.
•MPAA ratings : The particular rating that you have selected will be locked. In addition, more
restrictive ratings will be locked as well.
• Neither TV (FCC) ratings nor MPAA ratings apply to news programs.
English - 73
Page 74
Special Features
0 9
How to Set up Restrictions Using the Canadian English
Press the MENU button.
1
Press the … or † button to
select “Setup”, then press the
ENTER button.
Press the
… or † button to
select “V-Chip”, then press
the ENTER button.
Press the number buttons to
2
enter your current 4-digit pin
number.
(The default pin number for
a new TV set is “0000”.)
The “V-Chip” menu is
displayed.
Press the … or † button to
3
select “Canadian English”,
then press the ENTER button.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
<Canada>
Input
Picture
Sound
Channel
Setup
Setup
Language: English
Time
V-Chip
Caption
Blue Screen: Off
Melody: On
Color Weakness
PC
MoveEnterReturn
V-Chip
Enter PIN
*
Enter PINReturn
V-Chip
V-Chip Lock: On
TV Parental Guidelines
MPAA Rating
Canadian English
Canadian French
Change PIN
MoveEnterReturn
√
√
√
√
√
√
√
√
√
√
√
√
√
√
English - 74
Page 75
Press the … or † button to select a
4
appropriate restriction.
Press the ENTER button to activate the
restriction selected.
The “ ” symbol is indicated.
Press the EXIT button.
EExempt programming includes...news, sports,
documentaries and other information programming, talk
shows, music videos, and variety programming.
CProgramming intended for children under age 8.
C8+Programming generally considered acceptable for children
8 years and over to watch on their own.
GGeneral programming, suitable for all audiences.
PGParental Guidance.
14+Programming contains themes or content which may not
be suitable for viewers under the age of 14.
18+Adult programming.
Input
Picture
Sound
Channel
Setup
Canadian English
Block
E
C
C8+
G
PG
14+
18+
MoveEnterReturn
English - 75
Page 76
Special Features
0 9
How to Set up Restrictions Using the Canadian French
Press the MENU button.
1
Press the … or † button to
select “Setup”, then press the
ENTER button.
Press the
… or † button to
select “V-Chip”, then press
the ENTER button.
Press the number buttons to
2
enter your current 4-digit pin
number.
(The default pin number for
a new TV set is “0000”.)
The “V-Chip” menu is
displayed.
Press the … or † button to
3
select “Canadian French”,
then press the ENTER button.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
<Canada>
Input
Picture
Sound
Channel
Setup
Setup
Language: English
Time
V-Chip
Caption
Blue Screen: Off
Melody: On
Color Weakness
PC
MoveEnterReturn
V-Chip
Enter PIN
*
Enter PINReturn
V-Chip
V-Chip Lock: On
TV Parental Guidelines
MPAA Rating
Canadian English
Canadian French
Change PIN
MoveEnterReturn
√
√
√
√
√
√
√
√
√
√
√
√
√
√
English - 76
Page 77
Press the … or † button to select a
4
appropriate restriction.
Press the ENTER button to activate the
restriction selected.
The “ ” symbol is indicated.
Press the EXIT button.
EExempt programming includes...news, sports,
documentaries and other information programming, talk
shows, music videos, and variety programming.
GGeneral.
8 ans+ 8+ General-Not recommended for young children.
13 ans+ Programming may not be suitable for children under the
age of 13.
16 ans+ Programming is not suitable for children under the age of
16.
18 ans+ Programming restricted to adults.
Input
Picture
Sound
Channel
Setup
Canadian French
Block
E
G
+
8 ans
+
13 ans
+
16 ans
+
18 ans
MoveEnterReturn
English - 77
Page 78
Special Features
Viewing Closed Caption Information
Your TV decodes and displays the closed captions information that is broadcast along with some
television shows. These captions are usually subtitles for the hearing impaired or translations into
other languages. All VCRs record the closed caption signal from television programs, so prerecorded video tapes can also deliver closed-caption information. Check for the closed caption
symbol () on the tape’s package or your TV program-schedule.
Press the MENU button.
1
Press the … or † button to
select “Setup”, then press the
ENTER button.
Press the … or † button to
select “Caption”, then press
the ENTER button.
Press the ENTER button to
2
select “Caption”.
Press the … or † button to
select “On”, then press the
ENTER button.
Press the … or † button to
3
select “Mode”, then press
the ENTER button.
Press the … or † button to
select “Caption” or “Text”,
then press the ENTER button.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Setup
Language: English
Time
V-Chip
Caption
Blue Screen: Off
Melody: On
Color Weakness
PC
MoveEnterReturn
Caption
Caption: On
Mode: Caption
Channel: 1
Field: 1
MoveEnterReturn
Caption: On
Mode: Caption
Channel: 1
Field: 1
MoveEnterReturn
Caption
Off
On
Caption
Text
√
√
√
√
√
√
√
√
English - 78
• In “Caption” mode, caption appears at the bottom of the
screen, and they usually cover only a small portion of the
picture.
• In “Text” mode, information unrelated to the program, such as
news or weather, is displayed. Text often covers a large portion
of the screen.
Page 79
Depending on the particular
4
broadcast, it might be
necessary to make changes
to “Channel” and “Field”.
Press the … or † button to
select “Channel”, then press
the ENTER button.
Input
Picture
Sound
Channel
Setup
Caption
Caption: On
Mode: Caption
Channel: 1
Field: 1
MoveEnterReturn
√
√
√
√
Press the … or † button to
5
select “1” or “2”, then press
the ENTER button.
Press the … or † button to
6
select “Field”, then press the
ENTER button.
Press the … or † button to
select “1” or “2”, then press
the ENTER button.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Caption: On
Mode: Caption
Channel: 1
Field: 1
Caption: On
Mode: Caption
Channel: 1
Field: 1
Caption
1
2
MoveEnterReturn
Caption
1
2
MoveEnterReturn
• Different channels and fields display different information:
“Field 2” carries additional information that supplements the
information in “Field 1”. (For example, “Channel 1” may have
subtitles in English, while “Channel 2” has subtitles in Spanish.)
NOTES
• The Caption function doesn’t operate when the PIP is active.
• Misspellings and unusual characters sometimes occur during closed caption transmissions,
especially those of live events. There may be a small delay before captions appear when you
change channels. These are not malfunctions of the TV.
English - 79
Page 80
Special Features
Setting the Blue Screen Mode
If no signal is being received or the signal is very weak, a blue screen automatically replaces the
noisy picture background. If you wish to continue viewing the poor picture, you must set the “Blue
Screen” mode to “Off”.
Press the MENU button.
1
Press the … or † button to
select “Setup”, then press
the ENTER button.
Press the … or † button to
2
select “Blue Screen”, then
press the ENTER button.
Press the … or † button to
3
select “On” or “Off”, then
press the ENTER button.
Press the EXIT button to exit.
Language: English
Input
Time
V-Chip
Picture
Caption
Blue Screen: Off
Sound
Melody: On
Channel
Color Weakness
PC
Setup
Language: English
Input
Time
V-Chip
Picture
Caption
Blue Screen: Off
Sound
Melody: On
Channel
Color Weakness
PC
Setup
Language: English
Input
Time
V-Chip
Picture
Caption
Blue Screen: Off
Sound
Melody: On
Channel
Color Weakness
PC
Setup
Setup
MoveEnterReturn
Setup
MoveEnterReturn
Setup
Off
On
MoveEnterReturn
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
English - 80
Page 81
Setting The On/Off Melody
A melody sound can be set to come on when the TV is powered On or Off.
Press the MENU button.
1
Press the … or † button to
select “Setup”, then press the
ENTER button.
Press the … or † button to
2
select “Melody”, then press
the ENTER button.
Press the … or † button to
3
select “On”, then press the
ENTER button.
Press the EXIT button to exit
the menu.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Setup
Language: English
Time
V-Chip
Caption
Blue Screen: Off
Melody: On
Color Weakness
PC
MoveEnterReturn
Setup
Language: English
Time
V-Chip
Caption
Blue Screen: Off
Melody: On
Color Weakness
PC
MoveEnterReturn
Setup
Language: English
Time
V-Chip
Caption
Blue Screen: Off
Melody: On
Color Weakness
PC
MoveEnterReturn
Off
On
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
English - 81
Page 82
Special Features
Using the Color Weakness Enhancement Feature
This feature adjusts the Red, Blue or Green color to enhance the picture according to the user's
particular color weakness.
Press the MENU button.
1
Press the … or † button to
select “Setup”, then press
the ENTER button.
Press the … or † button to
2
select “Color Weakness”,
then press the ENTER button.
Press the ENTER button to
3
select “Color Weakness”.
Press the … or † button to
select “On”, then press the
ENTER button.
Language: English
Input
Time
V-Chip
Picture
Caption
Blue Screen: Off
Sound
Melody: On
Channel
Color Weakness
PC
Setup
Language: English
Input
Time
V-Chip
Picture
Caption
Blue Screen: Off
Sound
Melody: On
Channel
Color Weakness
PC
Setup
Color Weakness :On
Input
Red0
Green0
Picture
Blue0
Sound
Channel
Setup
Setup
MoveEnterReturn
Setup
MoveEnterReturn
Color Weakness
Off
On
MoveEnterReturn
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
English - 82
Press the … or † button to
4
select a color to be adjusted,
then press the ENTER button.
Press the œ or √ button to
adjust the value of a color
selected.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
▲
Red
▼
Color Weakness
Color Weakness : On
Red0
Green0
Blue0
MoveEnterReturn
Color Weakness
AdjustMoveReturn
√
0
Page 83
PC Display
Page 84
PC Display
Using Your TV as a Computer (PC) Display
How to Connect Your PC to the TV
This figure shows the Standard Connector-jack panel. The actual configuration on your TV may be
different, depending on the model.
TV Rear Panel
15Pin(D-Sub)
Cable
PC
NOTE
• The “SERVICE” jack is for repairs and software upgrades.
Audio Cable
English - 84
Page 85
Setting up Your PC Software (Based on Widows 98)
The Windows display-settings for a typical computer are shown below. The actual screens on your
PC will probably be different, depending upon your particular version of Windows and your
particular video card. However, even if your actual screens look different, the same basic setup
information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung
Dealer.)
First, click on “Settings” on the Windows start menu.
While “Settings” is highlighted, move the cursor so
that “control panel” is highlighted.
When the control panel screen appears,
click on “Display” and a display dialog-box
will appear.
Navigate to the “Settings” tab on the display dialog
box.
The two key variables that apply to the TV-PC interface
are “resolution” and “colors”. The correct settings for
these two variables are:
* Screen area (sometimes called “resolution”): 1024 x
768 pixels
* Colors: “24-bit” color (might also be expressed as
“16 million colors”).
If a vertical-frequency option exists on your display
settings dialog box, the correct value is “60” or “60
Hz”. Otherwise, just click “OK” and exit the dialog
box.
continued...
English - 85
Page 86
PC Display
Display Modes
Mode
VGA
SVGA
XGA
DTV
Resolution
640 x 350
720 x 400
640 x 480
800 x 600
832 x 624
1024 x 768
1920 x 1080i
1280 x 720p
720 x 483p
Horizontal Frequency [KHz]
31.47
31.47
37.93
31.47
35.00
37.86
37.50
43.27
35.16
37.88
48.08
46.87
53.67
49.73
48.36
56.40
60.02
33.75
45.00
31.47
Vertical Frequency [Hz]
70.00
70.00
85.00
60.00
66.70
72.80
75.00
85.00
56.30
60.30
72.20
75.00
85.10
74.60
60.00
70.10
75.00
60
60
60
Pixel Clock [MHz]
25.175
28.322
35.5
25.175
30.24
31.50
31.50
36.00
36.00
40.00
50.00
49.50
56.25
57.284
65.00
75.00
78.75
74.25
74.25
27
Sync Polarity (H/V)
+/
-//+
-
-
/+
-/-
-
/
/
-
-/-
-+/-
+/+
+/+
+/+
+/+
-
/+
-/-
/
-
+/
X
X
X
-
-
-
-
-
-
English - 86
NOTES
• Both screen position and size will vary, depending on the type of PC monitor and its resolution.
The table above shows all of the display modes that are supported:
* The interlace mode is not supported.
* The TV will operate abnormally if a non-standard video format is selected.
• When this TV is used as a PC display, 32-bit color is supported (over 16 million colors).
•Your PC display screen might appear different, depending on the manufacturer (and depending
on your particular version of Windows). Check your PC instruction book for information about
connecting your PC to a TV display-monitor.
• Same modes as PC are supported for the signal input to the DVI jack. Only a separate sync
signal is supported.
Page 87
Adjusting the Picture Quality
The purpose of picture quality adjustment is to remove or reduce picture noise. If the noise is not
removed by fine tuning alone, then do the frequency adjustments to the utmost and fine tune
again. After the noise has been reduced, re-adjust the picture so that it is aligned on the center of
screen.
Press the SOURCE button to select “PC”.
1
Press the MENU button.
2
Press the … or † button to
select “Setup”, then press the
ENTER button.
Press the … or † button to
3
select “PC”, then press the
ENTER button.
Press the … or † button to
4
select “Coarse” or “Fine”,
then press the ENTER button.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Setup
Language: English
Time
V-Chip
Caption
Blue Screen: Off
Melody: On
Color Weakness
PC
MoveEnterReturn
Setup
Language: English
Time
V-Chip
Caption
Blue Screen: Off
Melody: On
Color Weakness
PC
MoveEnterReturn
PC
Coarse
Fine
Position
Auto Adjustment
Recall
MoveEnterReturn
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
Pressing the œ or √ button
5
to remove the picture noise.
▲
Coarse
▼
1344
Press the EXIT button to exit.
▲
Fine
▼
0
NOTE
• This feature may change the width of the image. If necessary,
adjust the position to center.
English - 87
Page 88
PC Display
Changing the Picture Position
After connecting the TV to your PC, adjust the position of picture if it is not well-aligned.
Press the SOURCE button to select “PC”.
1
Press the MENU button.
2
Press the … or † button to
select “Setup”, then press the
ENTER button.
Press the … or † button to
3
select “PC”, then press the
ENTER button.
Press the … or † button to
4
select “Position”, then press
the ENTER button.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Setup
Language: English
Time
V-Chip
Caption
Blue Screen: Off
Melody: On
Color Weakness
PC
MoveEnterReturn
Setup
Language: English
Time
V-Chip
Caption
Blue Screen: Off
Melody: On
Color Weakness
PC
MoveEnterReturn
PC
Coarse
Fine
Position
Auto Adjustment
Recall
MoveEnterReturn
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
English - 88
Adjust the position of picture
5
by pressing the …/†/œ/√
button.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Position
▲
▼
▼
MoveEnterReturn
▼
NOTE
• If a PC signal is input to “DVI” or “HDMI”, you can’t adjust the
quality and position of picture.
Page 89
Adjusting the Picture Quality and Position Automatically
This feature allows the TV to self-adjust to the incoming video signal. The values of fine, coarse
and position are adjusted automatically.
Press the SOURCE button to select “PC”.
1
Press the MENU button.
2
Press the … or † button to
select “Setup”, then press the
ENTER button.
Press the … or † button to
3
select “PC”, then press the
ENTER button.
Press the … or † button to
4
select “Auto Adjustment”,
then press the ENTER button.
The picture quality and
position are automatically
adjusted, and the picture
returns to original view
about a few seconds later.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Setup
Language: English
Time
V-Chip
Caption
Blue Screen: Off
Melody: On
Color Weakness
PC
MoveEnterReturn
Setup
Language: English
Time
V-Chip
Caption
Blue Screen: Off
Melody: On
Color Weakness
PC
MoveEnterReturn
PC
Coarse
Fine
Position
Auto Adjustment
Recall
MoveEnterReturn
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
Press the EXIT button to exit.
Auto in Progress
Please Wait
English - 89
Page 90
PC Display
Initializing the Picture Settings
You can replace all picture settings with the factory default values.
Press the SOURCE button to select “PC”.
1
Press the MENU button.
2
Press the … or † button to
select “Setup”, then press the
ENTER button.
Press the … or † button to
3
select “PC”, then press the
ENTER button.
Press the … or † button to
4
select “Recall”, then press
the ENTER button.
The picture settings are
replaced with the factory
default values.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Setup
Language: English
Time
V-Chip
Caption
Blue Screen: Off
Melody: On
Color Weakness
PC
MoveEnterReturn
Setup
Language: English
Time
V-Chip
Caption
Blue Screen: Off
Melody: On
Color Weakness
PC
MoveEnterReturn
PC
Coarse
Fine
Position
Auto Adjustment
Recall
MoveEnterReturn
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
English - 90
Page 91
Changing the Picture Size (PC Mode)
You can select the picture size which best corresponds to your viewing requirements.
Press the SOURCE button to select “PC”.
1
NOTES
• The “Wide PC” and
“Expand” modes are
recommended for the PC
mode.
• In VGA (640x480) and
SVGA (800x600) modes,
the “Wide” and “4:3”
modes are available.
• In XGA (1024x768)
mode, the “Wide” mode
is available.
Press the MENU button.
2
Press the … or † button to
select “Picture”, then press
the ENTER button.
Press the … or † button to
select “Size”, then press the
ENTER button.
Press the œ or √ button to
3
select the screen format you
want, then press the ENTER
button.
Press the EXIT button to exit.
Input
Picture
Sound
Channel
Setup
Input
Picture
Sound
Channel
Setup
Mode: Standard
Color Tone: Warm1
Size: Wide
Digital NR: On
DNIe: On
My Color Control
Film Mode: Off
PIP
Wide TV Wide PC Expend4:3
Picture
MoveEnterReturn
Size
MoveEnterReturn
Alternate method
Press the P.SIZE button on the remote control repeatedly to select
one of the picture size settings.
•“Wide TV”: Scales the picture to the size of the TV screen
regardless of the aspect ratio of the input source.
•“Wide PC”: Scales the picture to 92% of the TV screen,
regardless of the aspect ratio of the input source. The picture
position ( , ) and size ( ) adjustment are available by
pressing the
• “Expand”: Scales the picture to the aspect ratio of the input
source.
• “4:3”: Displays the picture as it is without changing the aspect
ratio of input source.
Source (PC/DVI)
1920 x 1080i
1280 x 720
1024 x 768
720 x 483 (480p)
…/†/œ/√ button.
Others
Picture Size
Wide TV ➝ 4:3
Wide TV ➝ Wide PC ➝ Expand ➝ 4:3
Wide TV ➝ Wide PC ➝ Expand
Wide TV ➝ 4:3
Wide TV ➝ Wide PC ➝ Expand ➝ 4:3
√
√
√
√
√
√
√
√
English - 91
Page 92
SAMSUNG
Page 93
Appendix
Page 94
Appendix
Troubleshooting
If the TV seems to have a problem, first try this list of possible problems and solutions. If none of
these troubleshooting tips apply, then call your nearest service center.
Problem
Poor picture quality.
Poor sound quality.
No picture or sound.
No color, wrong colors or tints.
Picture rolls vertically.
The TV operates erratically.
Possible Solution
Try another channel.
Adjust the antenna.
Check all wire connections.
Try another channel.
Adjust the antenna.
Make sure the MUTE button is off.
Try another channel.
Press the SOURCE button.
Make sure the TV is plugged in.
Check the antenna connections.
Make sure the program is broadcasted in color.
Adjust the picture settings.
Adjust the antenna.
Check all wire connections.
If you are using a VCR, check the tracking.
Unplug the TV for 30 seconds, then try operating it
again.
English - 94
Your remote control does not
operate your TV.
The TV won’t switch on.
• The display panel used for the DLP TV is composed of many tiny pixels.
These, pixels may occasionally appear on the screen.
Press the MODE button to put your remote control
into TV mode.
Make sure the remote has batteries.
Make sure the wall outlet is working.
Make sure the remote has batteries.
Page 95
Cleaning and Maintaining Your TV
With proper care, your TV will give you many years of service. Please follow these guidelines to
get the maximum performance from your TV.
Placement
• Do not put the TV near extremely hot, cold, humid or dusty places.
• Do not place the TV near appliances with electric motors that create magnetic fields, such as
vacuum cleaners.
• Keep the ventilation openings clear; do not place the TV on a soft surface, such as cloth or
paper.
• Place the TV in a vertical position only.
Liquids
• Do not handle liquids near or on the TV. Liquids that spill into it can cause serious damage.
Cabinet
• Never open the cabinet or touch the parts inside.
•Wipe your TV with a clean, dry cloth. Never use water, cleaning fluids, wax, or chemicals.
• Do not put heavy objects on top of the cabinet.
• This DLP TV projects the image onto a large screen by applying an optical system.
If you place the TV set face down, it might cause a problem because dirt, or some other
contaminant may become attached to the inside of the TV set.
Temperature
• If your TV is suddenly moved from a cold to a warm place, unplug the power cord, and allow
at least two hours for moisture that may have formed inside the unit to dry completely.
Using Your TV in Another Country
If you plan to take your TV with you to a foreign country, please be aware of the different
television systems that are in use around the world. A TV designed for one system may not work
properly with another system due to differences in the TV channel frequencies.
Specifications
Model
Voltage
Frequency of Operation
Power Consumption
Dimension
(W x D x H)
Weight
HL-R4262W
AC 110-120V~
60Hz
200 watts
999 x 331.3 x 755.5 mm
39.33 x 13.04 x 29.74 inches
28 Kg / 61.73 lbs
HL-R4662W
AC 110-120V~
60Hz
200 watts
1088 x 341.5 x 814 mm
42.83 x 13.44 x 32.05 inches
30.3 Kg / 66.80 lbs
HL-R5062W
AC 110-120V~
60Hz
200 watts
1182 x 355.5 x 870 mm
46.54 x 14.00 x 34.25 inches
33 Kg / 72.75 lbs
HL-R5662W
AC 110-120V~
60Hz
200 watts
1330 x 387.5 x 962 mm
52.36 x 15.26 x 37.87 inches
36.7 Kg / 80.91 lbs
HL-R6162W
AC 110-120V~
200 watts
1446 x 466.5 x 1056.5 mm
56.93 x 18.37 x 41.59 inches
42.9 Kg / 94.58 lbs
60Hz
English - 95
Page 96
1-800-SAMSUNG (1-800-726-7864)
Samsung Electronics America
Service Division
400 Valley Road, Suite 201
Mount Arlington, NJ 07856
www.samsung.com
Samsung Electronics Canada Inc.
Samsung Customer Care