Samsung BN68-02628A-01 User Manual

Quick Setup Guide

LOC

Congratulations on the purchase of your new Samsung TV. Read this setup guide to get your TV up and running quickly.

STOP

Please do not return this unit.

If you have problems operating your

1-800-SAMSUNG (1-800-726-7864)

TV, call:

For web support please visit:

www.samsung.com/support

Step 1: Install the Stand

Follow the steps below to connect the TV to the stand.

✎

NOTE

Make sure to distinguish between the front and back of the Stand and

Guide Stand when assembling them.

Make sure that at least two persons lift and move the LED TV.

Stand the product up and fasten the screws. If you fasten the screws with

the LED TV placed down, it may lean to one side.

1-800-SAMSUNG (1-800-726-7864) Samsung Electronics America, Inc. 85 Challenger Road Ridgeﬁeld Park, NJ 07660-2112 Samsung Electronics Canada Inc. 55 Standish Court Mississauga, Ontario L5R 4B2 Call Center hours of operation: Mon-Sun, 9:00 AM -12 AM EST. To register this product, visit: www.samsung.com/ register.

Step 2: Connect Antenna or Cable

VHF/UHF Antenna

Antenna Cable (Not Supplied)

Use a 75 ohm (round) cable.

Connect Ant In to

• Wall cable jack

• VHF/UHF Antenna

• Cable or Satellite box Ant or Cable Out

Make sure the AC power cord is plugged in securely to the wall outlet and the TV.

Step 4: Run Plug & Play

When you turn on your TV for the ﬁrst time, it automatically launches the Plug & Play function. With Plug & Play, you can select the On Screen Display language, set the clock mode, and launch the TV’s channel memorizing process.

It also displays connection instructions similar to those in this guide. To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow

buttons on your remote. To make a selection, press the ENTER To skip a screen, press the MENU button. To turn on your TV, press the POWER

button on the remote or on the TV. To run Plug & Play, follow these steps:

button.

Step 3: Connect External Devices

Connecting an AV device (DVD / Blu-ray player, cable/satellite box, etc.)

Use one of the connections below to connect your TV to an external A/V device.

We recommend using HDMI for the highest picture quality.

HDMI to DVI Cable (Not Supplied)

Audio Cable (Not Supplied)

HDMI Cable (Not Supplied)

Best Connection

HD connection (up to 1080p)

Using an HDMI Cable

HDMI OUT

Device

Very Good Connection

HD connection (up to 1080p)

Using a HDMI to DVI Cable

DVI OUT

AUDIO OUT

Video Cable (Not Supplied)

Device

DVD / Blu-ray player / HD Cable Box / HD Satellite receiver (STB)

UN19C4000, UN22C4000, UN22C4010

1 Insert the stand body into the stand

base.

2 Screw the stand base to the stand

body.

RELEASE

LOCK

3

Slide the TV onto the stand body.

UN26C4000

Screws (M4 X L12)

Guide Stand

1 Connect the Guide Stand to the

Stand using four screws (M4 X L12) as shown

Stand

3 Fasten three screws (M4 X L8) at

2 With your TV upright, connect the

TV to the Stand as shown.

Front

Rear

position 1, and then fasten three screws (M4 X L8) at position 2.

Rear

1 Using your remote control, select

the language for the On Screen Display (OSD), and then press the

ENTERE button.

Select Language of the OSD.

Menu Language :

2 Select Home Use, and then

press the ENTERE button. If you select Store Demo, the TV will reset your picture and audio settings every 30 minutes.

3 Select Antenna Source to

memorize. If Antenna Source is Cable or Auto, you must select

your cable system type. After selecting source, select Search; then press the ENTERE button on your remote.

✎

Most cable systems are Standard (STD) systems, If you are not sure about what kind of cable system you have, contact your cable company.

✎

If your TV is attached to a cable or satellite box, skip Steps 3 through 5. Af ter Plug & Play is complete, set your TV to Channel 3 or 4, according to the

Anrenna Source :

Digital Cable System :

Analog Cable System :

Plug & Play

English

Español

Français

Move

Air

Cable

Auto

Move

Enter

Good Connection

Component connection (up to 1080p)

Using a Component Cable

Audio Cable (Not Supplied)

Component Cable (Not Supplied)

DVD / Blu-ray player / Cable Box / Satellite receiver / VCR

COMPONENT OUT

AUDIO OUT

Connecting an audio device (Home Theater, etc.)

Connect your TV to your Home Theater or other audio device to enjoy enhanced Sound quality.

headphone

Analog Audio connection

Using a Headphone

DVD / Blu-ray player

Connecting a PC

Connect your TV to a PC to use it as a Monitor.

directions for your cable or satellite box.

4 The TV memorizes the available channels. This process can take up to 45

minutes.

Top view

5 After the TV has memorized the channels, choose the Clock Mode. Select

Auto if you have a digital channel in your area. Select Manual if you don’t, or

if you have a cable or satellite box. When done, press the ENTERE button.

✎

If you select Manual, the clock setting screen appears.

Optical Cable (Not Supplied)

6 Select the daylight savings time setting: Off or On, and then press the

ENTERE button.

7 Select the time zone in which you live, and then press the ENTER

button.

Audio Cable (Not Supplied)

8 After the time zone screen, The connection method for best HD screen

quality is displayed. Press Right arrow button on your remote to view each screen in succession. Press the Blue button to skip this section.

9 The Enjoy your TV. screen appears. Then press the ENTER

If You Want to Rerun Plug & Play

button.

Optical Cable (Not Supplied)

Digital Audio connection

Using an Optical Cable

Digital Audio System

OPTICAL

Analog Audio connection

Using an Audio Cable

Ampliﬁer / DVD home theater

AUDIO IN

Digital Audio connection

Using an Optical Cable

Digital Audio System

OPTICAL

Using an EX-Link Cable Connection

Available Devices: External devices that support EX-Link.

Video Cable (Not Supplied)

Lowest Quality Connection

Audio/Video connection (480i only)

DVD / Blu-ray player / Cable Box / Satellite receiver / VCR

Audio Cable (Not Supplied)

D-Sub Cable (Not Supplied)

Using an Audio/Video Cable

VIDEO OUT

HDMI to DVI Cable (Not Supplied)

AUDIO OUT

Audio Cable (Not Supplied)

Device

HD connection

Using a HDMI to DVI Cable

DVI OUT

AUDIO OUT

Using a D-Sub Cable

AUDIO OUT

PC OUT

EX-LINK: Connector for service only.

1. Press the SOURCE button on your remote, then select TV mode.

2. Press the MENU button on your remote to display the menu.

3. Press the ▲ or ▼ button to select Setup, and then press the ENTER

button.

4. Press ENTER

again to select Plug & Play.

Step 5: Remote Control

CH LIST

POWER SOURCE

PRE-CH

HDMI

POWER SOURCE

PRE-CH

HDMI

SUM

Changing Channels and Adjusting the Volume

Remote Control Buttons and Functions

✎

This is a special remote control for the visually impaired and has Braille points on the Power, Channel and Volume buttons.

Turns the TV on and off.

Selects the HDMI mode directly.

Press to directly access channels.

Press to select additional channels

(digital) being broadcasted by the same

station. For example, to select channel

“54-3”, press “54”, then press “-” and “3”.

Adjusts the volume.

Brings up the OSD.

Displays Media Play.

Quickly select frequently used functions.

Returns to the previous menu.

Buttons used in the Channel list, Media Play menu,

etc.

Use these buttons in Media Play and Anynet+ modes.

(�: Controls recording for Samsung recorders that have

the Anynet+ feature)

POWER SOURCE

HDMI

PRE-CH

CH LIST

MEDIA.P

TOOLS

RETURN

A B C D

S.MODE

P.MODE

SLEEP

P.SIZE

FAV.CH

INFO

EXIT

MTS

Displays and selects the available video sources.

Returns to the previous channel.

Cuts off the sound temporarily.

Changes channels.

Displays the channel list on the screen.

Displays Favorite Channel Lists on the screen.

Displays information on the TV screen.

Selects the on-screen menu items and changes the values seen on the menu.

Exits the menu.

S.MODE: Press to select the sound mode. SLEEP: Automatically shuts off the TV at a preset time. MTS: Press to choose stereo, mono or Separate Audio

Program (SAP broadcast).

P.MODE: Press to select the picture mode. P.SIZE: Selects the picture size. CC: Controls the caption decoder.

Adjust the volume by pressing the Volume button

on the remote.

CH LIST

✎

You can also change the channels by pressing the

button on the front panel of your TV and adjust the volume by pressing the y button.

Selecting a Source

To watch a movie on your Blu-ray player or watch your favorite TV show, you must select the correct source. A source is a device, such as a Blu-ray/DVD player, a cable/satellite box, antenna or a cable TV input. Sources can be connected to your TV through the HDMI, DVI, Component, Composite, or D-sub connections, or through the Antenna or Cable In connections.

To view the signal from a source connected to the HDMI, DVI, Component, Composite, or D-sub jack, press the SOURCE button on your remote. Each time you press the SOURCE button, you change to a different source.

POWER SOURCE

Viewing the On Screen Menus

To view the On Screen Menus, follow these steps:

1. With the power on, press the MENU button on

your remote. The main menu appears. The menu’s left side has the following menu

MEDIA.P

TOOLS

options: Picture, Sound, Channel, Setup, Input, Application, and Support.

2. Press the ▲ or ▼ button on your remote to select a menu option, and then

press the ENTER

button.

3. When done using the menu, press the EXIT button on your remote to exit.

FAV.CH

INFO

Changing the Screen Size

Your TV has several screen size options, each designed to work best with speciﬁc types of video input. If you have a cable box or satellite receiver, it may have its own set of screen sizes as well.

To change the screen size, press the P.SIZE button on your remote. The ﬁrst time you press it, your TV displays the current setting. Thereafter, each time you press the P.SIZE button, you change the size of the picture on the screen.

The following sizes are available:

Change the channels by pressing the Channel button on the remote.

✎

If your TV is attached to a cable or satellite box, change the channel using the box’s remote.

Changing the Picture Mode

Your TV has three preset Picture Modes with factory adjusted settings, each designed to give you an excellent picture under speciﬁc conditions.

To change the Picture mode, press the P.MODE button on your remote. The ﬁrst time you press it, your TV displays the current setting. Thereafter, each time you press the P.MODE button, you change the mode of the picture on the screen.

The Picture Modes are listed and described in the table below:

Mode

Dynamic

Description

Brightens picture. For a vibrant, enhanced image in brightly lit or sunny room.

Standard

Movie

For a bright, detailed picture in a normally lit room. For a studio quality cinema picture in a dimly lit or dark room.

To change the Picture Mode, follow these steps:

1. With the TV on, press the TOOLS button on your remote. The Tools menu

appears.

2. Using the ▲ or ▼ on your remote, select Picture Mode.

3. On the Picture mode menu, use the ◄ or ► on your remote to select the Picture Mode you want.

4. Press the EXIT button to exit the menu.

Setting the Clock

Before you can use your TV’s On/Off Timer, you must set the clock. To set the clock, follow these steps:

1. Turn on your TV, press the MENU button on your remote, then select Setup → Time.

2. Select Clock Mode, and then press the ENTER

3. Choose Auto or Manual.

If you select Auto, the current time will be set automatically using the time

from a digital channel.

If you select Manual, you can set the Month, Day, Year, Hour, Minute

and am/pm directly by pressing up, down, left and right arrow button on your remote.

4. Press the RETURN button on your remote when done.

button.

Install the Batteries into the Remote

To install batteries into your remote control, follow these steps:

1. Lift the cover on the back of the remote upward as shown in the

ﬁgure to the right.

2. Install two AAA batteries.

✎

Make sure to match the + and - ends of the batteries to the diagram in the battery compartment.

3. Replace the cover.

16:9 Wide screen 4:3 Standard screen Wide Fit

Zoom 1 Zoom 2 Screen Fit

✎

Screen Fit displays the full image without any cut-off when HDMI (720p / 1080i / 1080p) or Component (1080i / 1080p) signals are inputted.

Connecting a USB Device for Media Play

You can enjoy photo, music, and movie ﬁles stored on a USB device by connecting it to the TV and using the Media Play feature. For Media Play operating instructions, please see your Owner’s Manual.

1. Turn on your TV.

2. Connect a USB device containing photo, music and/or movie ﬁles to the USB

1 or USB2 (HDD) jack on the side of the TV.

3. When the Input selection screen appears, press the ENTER remote to select Media Play (USB).

MediaPlay

Videos

Device

Device Mode

Enter

button on your

BN68-02628A-01

Return