Touch only manual function button.
Regardless of Microwave, Fan oven, Grill, Combination,
Fast Preheat, Defrost, Steam Clean, +, - , Pause/Cancel.
2.
All manual function are lit for 20 seconds.
3.
Cook food manually according to cooking guide.
The steam provided by steam clean system will soak the cavity
surface. After using steam clean function, you can easily clean the
cavity of oven.
☛
Use this function only after the oven has completely cooled.
(Room temperature)
☛
Use normal water only and not distilled water.
☛
The water in the oven will be very hot due to the steam cleaning
function
☛
To set stand by active function press any manual function buttons.
LCD : MANUAL COOK
Result: Buttons are lit.
1. Press the Steam Clean ( ) button.
(Bulb does work during Steam cleaning time)
Result:LCD : FILL WATER BOWL/ TO CORRECT
2.
Open the Door.
3.
Fill with water about half inside the water bowl.
(The half is about 30ml.)
4.
Please attach the water bowl in right side of the oven.
5.
Close the door.
6.
Press the
Result:LCD : CLEANING
7.
Open the Door.
LEVEL/ PLACE IN OVEN/ PRESS START
Start/Scan On
(The indicator in LCD will be
button.
reduced as cook time is counted down.)
8.
Please clean cavity of oven with dried kitchen cloth or
paper towel.
Remove the turntable and only under rack with kitchen
paper.
Warning!
•Use water bowl only during
•When cooking non-liquid items, take out water bowl it will melt and cause fire
to the smart oven.
“Steam Clean”
mode.
2
Control Panel Oven
VENTILATION HOLES
DOOR
1
2
3
4
5
6
7
8
9
10
11
12
13
DOOR
HANDLE
DOOR LATCHES
TURNTABLE
HEATING ELEMENT
COUPLER
ROLLER RING
VENTILATION
HOLES
SAFETY
INTERLOCK
HOLES
DISPLAY
CONTROL
PANEL
SCANNER
GB
1. CHILLED/FROZEN FUNCTION
MICROWAVE
2.
3.
FAN OVEN
4.
GRILL
5.
MANUAL COOK MODE : TIME/WEIGHT
6.
PAUSE/CANCEL
7.
QUANTITY
8.
SCANNER
9.
DEFROST
10.
MICROWAVE+FAN OVEN
11.
FAST PREHEAT
12.
STEAM CLEAN
13.
START/SCAN ON
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
3
Accessories
Using this Instruction Booklet
Depending on the model that you have purchased, you are supplied
GB
with several accessories that can be used in a variety of ways.
1.
Coupler
the base of the oven.
Purpose:
2.
Roller ring
Purpose:
3.
Turntable
fitting on to the coupler.
Purpose:
4. Metal racks (High rack, Low rack), to be placed on the
turntable.
Purpose:The metal racks can be used to cook two
5. Clean water bowl, to be placed in the right side of the
oven.
Purpose:The water bowl can be used to clean.
, to be placed correctly over the motor shaft in
The coupler rotates the turntable.
, to be placed in the center of the oven.
The roller ring supports the turntable.
, to be placed on the roller ring with the center
The turntable serves as the main cooking
surface; it can be easily removed for
cleaning.
dishes at the same time. A small dish may be
placed on the turntable and a second dish on
the rack. The metal racks can be used in grill, fan oven and combination cooking.
Thank you for purchasing a SAMSUNG smart oven. Your
Owner’s Instructions contains valuable information on cooking
with your new smart oven:
•Safety precautions
•Accessories and cookware
•Useful cooking tips
At the end of the booklet you will find illustrations of the oven,
and more importantly the control panel, so that you can find the
buttons more easily.
The illustrations in the step-by-step procedures use two different
symbols
.
☛✉
ImportantNote
PRECAUTIONS TO AVOID POSSIBLE EXPOSURE TO
EXCESSIVE MICROWAVE ENERGY
Failure to observe the following safety precautions may result in harmful
exposure to microwave energy.
(a) Under no circumstances should any attempt be made to operate the oven
with the door open or to tamper with the safety interlocks (door latches) or to
insert anything into the safety interlock holes.
(b) Do not place any object between the oven door and front face, or allow food
or cleaner residues to accumulate on sealing surfaces. Ensure that the door
and door sealing surfaces are kept clean by wiping after use with first a damp
cloth and then a final wipe with a soft dry cloth.
(c) Do not operate the oven if it is damaged until it has been repaired by a
qualified microwave service technician trained by the manufacturer.
It is particularly important that the oven door closes properly and that there is
no damage to the:
(1) Door, door seals and sealing surfaces
(2) Door hinges (broken or loose)
(3) Power cable
(d) The oven should not be adjusted or repaired by anyone other than a properly
qualified microwave service technician trained by the manufacturer.
4
Safety Precautions
I
MPORTANT SAFETY INSTRUCTIONS.
READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.
Before cooking food or liquids in your smart oven, please check that
the following safety precautions are taken.
1. DO NOT use any metalic cookware in the smart oven:
•Metalic containers
•Dinnerware with gold or silver trimmings
•Skewers, forks, etc.
Reason: Electric arcing or sparking may occur and may damage the oven.
2. DO NOT heat:
•Airtight or vacuum-sealed bottles, jars, containers. Ex) Baby food jars
•Airtight food. Ex) Eggs, nuts in shells, tomatoes
Reason: The increase in pressure may cause them to explode.
Tip:Remove lids and pierce skins, bags, etc.
3. DO NOT operate the smart oven when it is empty.
Reason: The oven walls may be damaged.
Tip:Leave a glass of water inside the oven at all times. The water will
4. DO NOT cover the rear ventilation slots with cloths or paper.
Reason: The cloths or paper may catch fire as hot air is evacuated from the
5. ALWAYS use oven gloves when removing a dish from the oven.
Reason: Some dishes absorb microwaves and heat is always transferred
6. DO NOT touch heating elements or interior oven walls.
Reason: These walls may be hot enough to burn skin even after cooking is
7. To reduce the risk of fire in the oven cavity
•Do not store flammable materials in the oven
•Remove wire twist ties from paper or plastic bags
•Do not use your smart oven to dry newspapers
•If smoke is observed, keep the oven door closed and switch off or
8. Take particular care when heating liquids and baby foods.
•ALWAYS allow a standing time of at least 20 seconds after the oven has
•Stir during heating if necessary and ALWAYS stir after heating.
•To prevent eruptive boiling and possible scalding, you should stir before,
•In the event of scalding, follow these FIRST AID instructions :
•NEVER fill the container to the top and choose a container that is wider at
•ALWAYS check the temperature of baby food or milk before giving it to
absorb the microwaves if you accidentally set the oven going when
it is empty.
oven.
from the food to the dish. The dishes are therefore
finished, though they do not appear to be so. Keep away from hot
spot. Do not allow inflammable materials to come into contact with
any interior area of the oven. Let the oven cool down first.
disconnect the oven from the power supply.
been switched off to allow the temperature to equalize.
during, and after heating.
*Immerse hand in cold water for at least 10 minutes.
*Cover with clean, dry dressing.
*Do not apply any creams, oils or lotions.
the top than at the bottom to prevent the liquid from boiling over. Bottles
with narrow necks may also explode if overheated.
the baby.
hot.
•
NEVER
heat a baby's bottle with the teat on, as the bottle may explode if
overheated.
•During microwave heating of beverages, there are results in delayed eruptive
boiling, therefore care has to be taken when handling the container.
9.
Be careful not to damage the power cable.
•Do not immerse power cable or plug in water and keep power cable away
from heated surfaces.
•Do not operate this appliance if it has a damaged power cable or plug.
10.
Stand at arm’s length from the oven when opening the door.
Reason: The hot air or steam released may cause scalding.
11.
Keep the inside of the oven clean.
•Clean the inside of the oven after each use with a mild detergent solution, but
let the smart oven cool down before cleaning in order to avoid injury.
Reason: Food particles or spattered oils stuck to oven walls or floor can cause
12.
“Clicking” sound might be noticed while operating, especially in defrosting mode.
Reason: When the power output is changing electrically, you may hear that
13.
If the smart oven is operating without any load, the power will cut off automatically
for safety. After standing for over 30 min, you can operate the oven normally.
•Do not worry is the oven continues to work after cooking has finished.
the damage of painting and reduce the efficiency of the oven.
sound. This is normal.
Reason: This product is designed to fan for 5 minutes, not operating smart
oven, to cool down the inner electronic parts when the stop button
is pressed or the door is opened after finishing cooking in case that
the oven operates for some minutes in cooking ( Fan Oven,
Combination, Fast Preheat ). When cooking has finished, the oven
will beep and flash “0” four times. The oven will then beep once per
minute.
IMPORTANT SAFETY INSTRUCTIONS
During cooking, you should look into the oven from time to time when food is being
heated or cooked in disposable containers of plastic paper or other combustible
material.
WARNING:
Do not use the door or door seals are damaged, the oven must not be operated until it
has been repaired by a competent person.
WARNING:
It is hazardous for anyone other than a comperent person to carry out any service or
repair operation which involves the removal of a cover which gives protection against
exposure to microwave energy.
WARNING:
Liquids and other foods must not be heated in sealed containers since they are liable
to explode.
WARNING:
Only allow children to use the oven without supervicion when adequate instructions
have been given so that the child is able to use the oven in a safe way and
understands the hazards of improper use.
WARNING:
Oven casing and door will get hot during fan oven and combination cooking.
☛
DO NOT
operate the smart oven without the coupler, roller ring and
turntable.
GB
5
Installing Your Smart Oven
Setting the Time
This smart oven can be placed almost anywhere (kitchen work
GB
surface or shelf, movable trolley, table).
10cm
20cm
above
85 cm
of the floor
behind
10cm on
the side
1.
When you install your oven, make sure there is adequate
ventilation for your oven by leaving at least 10 cm
(4 inches) of space behind, and on the sides of the oven
and 20 cm (8 inches) of space above the oven and 85 cm
(33 inches) of the floor.
2.
Remove all packing materials inside the oven.
Install the roller ring and turntable.
Check that the turntable rotates freely.
3.
This smart oven has to be positioned so that plug is
accessible.
☛Never block the air vents as the oven may overheat and
automatically switch itself off. It will remain inoperable until it has
cooled sufficiently.
☛For your personal safety, plug the cable into a 3-pin, 230V, 50Hz, AC
earthed socket. If the power cable of this appliance is damaged, it
must be replaced by the manufacturer or its service agent or a
similarly qualified person in order to avoid a hazard.
☛Do not install the smart oven in hot or damp surroundings like next to
a traditional oven or radiator. The power supply specifications of the
oven must be respected and any extension cable used must be of the
same standard as the power cable supplied with the oven. Wipe the
interior and the door seal with a damp cloth before using your smart
oven for the first time.
1. Plug your oven into a standard household socket.
Result:LCD : SET HOUR / .
2. Set hour by using ( / )
Result:LCD : SET HOUR /
3.
Press the
Result:LCD : SET MINUTE /
4.
Set minute by using / button.
Result:LCD : PRESS START
5.
Press the
Clock set is finished.
/ PRESS START
Start/Scan On
/ PRESS START
Start/Scan On
button.
button.
button.
6
Selecting the Display Weight
How a Smart Oven Works
The weight unit of this oven is basically set in “Grams”
☛
To set stand by active function press any manual function buttons.
Result: Buttons are lit.
LCD : MANUAL COOK
1. If you want to change the weight unit to “LBS”,
Press the button hold on 5 seconds.
Result:LCD : LB SELECTED
2. To set weight unit back to “Grams”, Press the button
again hold on 5 seconds.
Result:LCD : GRAM SELECTED
Microwaves are high-frequency electromagnetic waves; the energy
released enables food to be cooked or reheated without changing
either the form or the colour.
You can use your smart oven to:
•Defrost
•Preheat
•Cook
Cooking Principle
1. The microwaves generated by the magnetron
reflected at cavity and are distributed uniformly as
the food rotates on the turntable. The food is thus
cooked evenly.
2. The microwaves are absorbed by the food up to a
depth of about 2.5 cm(1 inch). Cooking then
continues as the heat is dissipated within the food.
3. Cooking times vary according to the container used
and the properties of the food:
•Quantity and density
•Water content
•Initial temperature (refrigerated, frozen or
ambient)
☛As the centre of the food is cooked by heat conduction, cooking
continues even when you have taken the food out of the oven.
Standing times specified in recipes and in this booklet must therefore
be respected to ensure:
•Even cooking of the food right to the centre.
•The same temperature throughout the food.
GB
7
What to Do if You are in Doubt or You have a Problem
How to Scan
Becoming familiar with a new appliance always takes a little time. If you
have any of the problems listed below, try the solutions given. They may
GB
save you the time and inconvenience of an unnecessary service call.
◆
The following are normal occurrences.
•Condensation inside the oven
•Air flow around the door and outer casing
•Light reflection around the door and outer casing
•Steam escaping from around the door or vents
◆
The food is not cooked at all
•Has the timer been set correctly, and the
•Is the door close?
•The electric circuit may have been overloaded, and may have caused the fuse to
have blown.
◆
The food is either overcooked or undercooked
•Was the appropriate cooking length set for the type of food?
•Was an appropriate power level chosen?
◆
Sparking occurs in the oven
This is known as arcing and can be caused by
•A dish with metal trimmings
•A fork or other metal utensil inside the oven
•Aluminium foil being too close to the oven walls
(NB foil can be used to cover food - do not allow to get too close to oven wall)
◆
The oven causes interference with radios or televisions
•Slight interference may be observed on televisions or radios when the oven is
operating. This is normal.
*Solution: Install the oven away from televisions, radios and aerials.
•If interference is detected by the oven’s microprocessor, the display may be reset.
*Solution: Disconnect the power plug and reconnect it. Reset the time.
◆
“ERROR” message
•Scan error
LCD : SCAN OFF - Er
PRESS “STOP“
•Not complete fast preheart in 30min
LCD : PREHEATING - Er
PRESS “STOP“
•Sensor open
LCD1 : SENSOR OPEN - Er
LCD2 : PRESS “STOP”
•Sensor short
LCD1 : SENSOR SHORT - Er
LCD2 : PRESS “STOP”
Start/Scan On
function pressed?
If the above guidelines do not enable you to solve the problem, then
contact your local Samsung customer service centre.
Please have the following information read;
•The model and serial numbers, normally printed on the rear of
the oven
•Your warranty details
•A clear description of the problem
Then contact your local dealer or SAMSUNG aftersales service.
1. Press the Start/Scan On button.
Result:The Chilled/Frozen, Quantity and Pause/
scanner
2.
Place SmartCode against the scanner.
3.
After 2 ~ 3 seconds, oven will beep to confirm SmartCode
has been read.
4.
Follow instructions on Oven display.
☛
Recommend to Scan
•To scan, the best way is to place smartcode horizontally or vertically
againts the scanner.
☛
Fail to Scan
•Keep the scanner window clean.
(Remove dust particles and check scratches)
•Check the range of DOF (within 20mm away from Scanner) and scan
again.
•Call a serviceman if it continuously fails to scan 5 times as the above
.Precaution in handling
•Dust particles on the scanner window may cause a scanner to malfunction.
•Scratches on the scanner window may cause a scanner to malfunction so
attention is required.
Cancel button are lit for 20 seconds.
LCD : SCANNING
(The indicator in LCD will scroll)
◆Remove sleeve from the meal.(of applicable)
◆Find the SmardCode on the ready meal pack.
8
Smart Code Scan Cooking
Chilled Food (chilled only)
☛For quick and easy to follow cook instructions simply scan the
smart code an food package.
☛
To set stand by active function press the Start/Scan On button
Result:Buttons are litGOScanner ready).
LCD : SCANNING
(The indicator in LCD will scroll)
1. Scan the smart code of food package in the center of
scanner window and hold still.
LCD : Food company display
After 2 seconds.
LCD : COOK FROM
CHILLED ONLY
2. After 3 seconds, follow preparation guide in LCDUG
3.
Open the door and follow preparation guide in LCD
4.
Door close
LCD : PRESS START
5. Press the Start/Scan On Button.
LCD : COOKING
(The indicator in LCD will be reduced
as cook time is counted down.)
Result:The oven light comes on and the turntable
starts rotating. Cooking starts and when it
has finished:
◆
✉If you want to adjust the cooking time, use the (more)/ (less)
buttons. See page12 for the more/less function.
The oven will beep and flash “ : 0” four
times. (If Clock set, current time is
displayed) The oven will then beep once
per minute.
Chilled Food (Home freezing)
GB
☛For quick and easy to follow cook instructions simply scan the
smart code on food package.
☛
To set stand by active function press the Start/Scan On button
Result:Buttons are lit (Scanner ready).
LCD : SCANNING
(The indicator in LCD will scroll)
1. Scan the smart code of food package in the center of
scanner window and hold still.
LCD : Food company display
After 2 seconds.
LCD : COOK FROM
CHILLED/FROZEN?
2. Select status with Chilled/frozen Button.
LCD : FROZEN or
UG
✉If you want to adjust the cooking time, use the (more)/ (less)
buttons. See page12 for the more/less function.
CHILLED
After 3 seconds, follow preparation guide in LCD.
3.
Open the door and follow preparation guide in LCD
4.
Door close
LCD : PRESS START
5. Press the Start/Scan On Button.
LCD : COOKING
(The indicator in LCD will be reduced
as cook time is counted down.)
Result:The oven light comes on and the turntable
starts rotating. Cooking starts and when it
has finished:
◆
The oven will beep and flash “ : 0” four
times. (If Clock set, current time is
displayed) The oven will then beep once
per minute.
.
9
Loading...
+ 19 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.