Samsung 959NF Service manual

COLOR MONITOR

AQ17HS/AQ17IS/AQ17NS
AQ19MS/AQ19IS/AQ19NS/AQ19FS

SERVICE

Manual

COLOR MONITOR CONTENTS

1. Precautions

2. Product Specifications

3. Disassembly & Reassembly

4. Alignment & Adjustments

5. Troubleshooting

6. Exploded View & Parts List

7. Electrical Parts List

8. Block Diagram

9. Wiring Diagram

10. Schematic Diagrams

1 Precautions

!

DEVICE
UNDER
TEST

TEST ALL

EXPOSED METAL

SURFACES

(READING SHOULD

NOT BE ABOVE 0.5mA)

LEAKAGE
CURRENT

TESTER

2-WIRE CORD

ALSO TEST WITH

PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED)

EARTH

GROUND

1-1 Safety Precautions

WARNINGS

1. For continued safety, do not attempt to modify the
circuit board.

2. Disconnect the AC power before servicing.

3. When the chassis is operating, semiconductor
heatsinks are potential shock hazards.

1-1-1 Servicing the High Voltage and CRT :

WARNING: A high voltage VR replaced in the wrong

direction may cause excessive X-ray
emissions.

1. When servicing the high voltage system, remove
the static charge by connecting a 10 kohm resistor
in series with an insulated wire (such as a test
probe) between the chassis and the anode lead.

2. When troubleshooting a monitor with excessively
HV, avoid being unnecessarily close to the monitor.
Do not operate the monitor for longer than is
necessary to locate the cause of excessive voltage.

3. High voltage should always be kept at the rated
value, no higher. Only when high voltage is
excessive are X-rays capable of penetrating the shell
of the CRT, including the lead in glass material.
Operation at high voltages may also cause failure of
the CRT or high voltage circuitry.

4. When the HV regulator is operating properly, there
is no possibility of an X-ray problem. Make sure the
HV does not exceed its specified value and that it is
regulating correctly.

5. The CRT is especially designed to prohibit
X-ray emissions. To ensure continued X-ray
protection, replace the CRT only with one that is
the same or equivalent type as the original.

6. Handle the CRT only when wearing shatterproof
goggles and after completely discharging the high
voltage anode.

7. Do not lift the CRT by the neck.

1-1-2 Fire and Shock Hazard :

Before returning the monitor to the user, perform the
following safety checks:

1. Inspect each lead dress to make certain that the
leads are not pinched or that hardware is not
lodged between the chassis and other metal parts in
the monitor.

2. Inspect all protective devices such as nonmetallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacitor networks, mechanical
insulators, etc.

3. Leakage Current Hot Check (Figure 1-1):

WARNING: Do not use an isolation transformer during

this test.

Use a leakage current tester or a metering system
that complies with American National Standards
Institute (ANSI C101.1, Leakage Current for

Appliances), and Underwriters Laboratories (UL
Publication UL1410, 59.7).

4. With the unit completely reassembled, plug the AC
line cord directly into a 120V AC outlet. With the
unit’s AC switch first in the ON position and then
OFF, measure the current between a known earth
ground (metal water pipe, conduit, etc.) and all
exposed metal parts, including: metal cabinets,
screwheads and control shafts. The current
measured should not exceed 0.5 milliamp. Reverse
the power-plug prongs in the AC outlet and repeat
the test.

Figure 1-1. Leakage Current Test Circuit

1-1-3 Product Safety Notices

Some electrical and mechanical parts have special
safety-related characteristics which are often not
evident from visual inspection. The protection they give
may not be obtained by replacing them with
components rated for higher voltage, wattage, etc. Parts
that have special safety characteristics are identified by

on schematics and parts lists. A substitute
replacement that does not have the same safety
characteristics as the recommended replacement part
might create shock, fire and / or other hazards. Product
safety is under review continuously and new
instructions are issued whenever appropriate.

Components identified by on schematics and parts
lists must be sealed by a soldering iron after
replacement and adjustment.

AQ17HS/AQ17IS/AQ17NS
AQ19MS/AQ19IS/AQ19NS/AQ19FS

1-1

1 Precautions

1-2 Servicing Precautions

WARNING1: First read the “Safety Precautions” section of this manual. If unforeseen circumstances

create conflict between the servicing precautions and safety precautions, always
follow the safety precautions.

WARNING2: A high voltage VR replaced in the wrong direction may cause excessive X-ray

emissions.

WARNING3: An electrolytic capacitor installed with the wrong polarity might explode.

1. Servicing precautions are printed on the cabinet,
and should be followed closely.

2. Always unplug the unit’s AC power cord from the
AC power source before attempting to: (a) remove
or reinstall any component or assembly, (b)
disconnect PCB plugs or connectors, (c) connect all
test components in parallel with an electrolytic
capacitor.

3. Some components are raised above the printed
circuit board for safety. An insulation tube or tape
is sometimes used. The internal wiring is
sometimes clamped to prevent contact with
thermally hot components. Reinstall all such
elements to their original position.

4. After servicing, always check that the screws,
components and wiring have been correctly
reinstalled. Make sure that the area around the
serviced part has not been damaged.

5. Check the insulation between the blades of the AC
plug and accessible conductive parts (examples:
metal panels, input terminals and earphone jacks).

6. Insulation Checking Procedure: Disconnect the
power cord from the AC source and turn the power
switch ON. Connect an insulation resistance meter
(500 V) to the blades of the AC plug.

The insulation resistance between each blade of the
AC plug and accessible conductive parts (see
above) should be greater than 1 megohm.

7. Never defeat any of the +B voltage interlocks. Do
not apply AC power to the unit (or any of its
assemblies) unless all solid-state heat sinks are
correctly installed.

8. Always connect a test instrument’s ground lead to
the instrument chassis ground before connecting
the positive lead; always remove the instrument’s
ground lead last.

1-3 Electrostatically Sensitive Devices (ESD) Precautions

Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly
called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some field­effect transistors. The following techniques will reduce the incidence of component damage caused by static electricity.

1. Immediately before handling any semiconductor
components or assemblies, drain the electrostatic
charge from your body by touching a known earth
ground. Alternatively, wear a discharging wrist­strap device. To avoid a shock hazard, be sure to
remove the wrist strap before applying power to
the monitor.

2. After removing an ESD-equipped assembly, place it
on a conductive surface such as aluminum foil to
prevent accumulation of an electrostatic charge.

3. Do not use freon-propelled chemicals. These can
generate electrical charges sufficient to damage
ESDs.

4. Use only a grounded-tip soldering iron to solder or
desolder ESDs.

5. Use only an anti-static solder removal device. Some
solder removal devices not classified as “anti-static”
can generate electrical charges sufficient to damage
ESDs.

6. Do not remove a replacement ESD from its
protective package until you are ready to install it.
Most replacement ESDs are packaged with leads
that are electrically shorted together by conductive
foam, aluminum foil or other conductive materials.

7. Immediately before removing the protective
material from the leads of a replacement ESD,
touch the protective material to the chassis or
circuit assembly into which the device will be
installed.

Caution: Be sure no power is applied to the

chassis or circuit and observe all
other safety precautions.

8. Minimize body motions when handling
unpackaged replacement ESDs. Motions such as
brushing clothes together, or lifting your foot from
a carpeted floor can generate enough static
electricity to damage an ESD.

9. Indicates ESDs on the Schematic Diagram in
this manual.

1-2 AQ17HS/AQ17IS/AQ17NS

AQ19MS/AQ19IS/AQ19NS/AQ19FS

2 Product Specifications

2-1 Specifications

Item

Picture Tube: 17-Inch (43 cm): 16-inch (40.6 cm) viewable, 19-Inch (48.2 cm): 18-inch (45.8 cm) viewable,

17”/19”: 0.26 mm Dot pitch,
Full-square tube / Perfect Flatmess, 90˚ Deflection,
Anti-Reflection coating with Anti-electrastatic, Medium short persistence phosphor

Scanning Frequency Horizontal : AQ17HS/AQ17IS/AQ17NS: 30 kHz ~ 96 kHz (Automatic)

AQ19MS/AQ19IS/AQ19FS: 30 kHz ~ 96 kHz (Automatic), AQ19NS: 30kHz ~ 110kHz

(Automatic) Vertical : 50 Hz ~ 160 Hz (Automatic)

Display Colors Unlimited colors

Maximum Resolution Horizontal : 1600 Pixels, Vertical : 1200 Pixels

Input Video Signal Analog, 0.7 Vp-p positive at 75 Ω, internally terminated

Input Sync Signal Separate Sync : TTL level positive/negative

Composite Sync : TTL level positive/negative
Sync-on-Green Coptional : Composite sync 0.3 Vp-p negative (Video on Vp-p positive)

Maximum Pixel Clock rate 17” : 250 MHz, 19”MS/IS/FS : 250 MHz, 19”NS : 290 MHz

Active Display 17” ; Horizontal : 312 mm, Vertical : 234 mm

19” ; Horizontal : 352 mm, Vertical : 264 mm

Input Voltage AC 90 ~ 264 Volts, 60/ 50 Hz ± 3 Hz

Power Consumption (nominal) 17”: 90 Watt , 19”: 110 Watt

Description

(Automatic)

Dimensions (W x D x H)
Unit / Carton
AQ17HS 15.7 x 16.2 x 16.2 Inches (398 x 412 x 412 mm) / 18.3 x 20.2 x 18 Inches (464 x 512 x 458 mm)
AQ17IS 15.7 x 16.2 x 16.2 Inches (398 x 412 x 412 mm) / 19.3 x 22.5 x 18 Inches (490 x 570 x 458 mm)
AQ17NS 16.4 x 17.3 x 17.3 Inches (415 x 438 x 448 mm) / 22.2 x 22.9 x 21.6 Inches (564 x 581 x 548 mm)
AQ19MS 17.3 x 17.9 x 18.1 Inches (440 x 454 x 461 mm) / 22.3 x 22.8 x 21.2 Inches (566 x 580 x 540 mm)
AQ19IS 17.3 x 18.1 x 18.1 Inches (440 x 460 x 461 mm) / 22.1 x 25 x 21.2 Inches (560 x 635 x 540 mm)
AQ19NS 18.5 x 18.0 x 19.4 Inches (468 x 458 x 493 mm) / 22.5 x 24.4 x 22.6 Inches (571 x 620 x574 mm)
AQ19FS 17.6 x 16.3 x 17.7 Inches (446 x 413.5 x 450 mm) / 21.4 x 22.8 x 21.1 Inches (542 x 580 x 535 mm)

Weight (Net/Gross)
AQ17HS 15.6 kg (34.4 lbs) / 17.5 kg (38.6 lbs)
AQ17IS 17.0 kg (37.5 lbs) / 19.5 kg (43.0 lbs)
AQ17NS 19.7 kg (43.4 lbs) / 23.0 kg (50.7 lbs)
AQ19MS 19.0 kg (41.9 lbs) / 21.5 kg (47.4 lbs)
AQ19IS 21.0 kg (46.3 lbs) / 23.5 kg (51.8 lbs)
AQ19NS 25.3 kg (55.8 lbs) / 29.3 kg (64.6 lbs)
AQ19FS 22.0 kg (48.5 lbs) / 24.5 kg (54.0 lbs)

Environmental Considerations Operating Temperature : 32°F ~ 104°F (0°C ~ 40°C)

Humidity : 10 % ~ 80 %
Storage Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Humidity : 5 % ~ 95 %

• AQ17HS/AQ17IS/AQ17NS/AQ19MS/AQ19IS/AQ19NS/AQ19FS complies with TCO 99 recommendations for
reduced electromagnetic fields.

• Designs and specifications are subject to change without prior notice.

AQ17HS/AQ17IS/AQ17NS
AQ19MS/AQ19IS/AQ19NS/AQ19FS

2-1

2 Product Specifications

QRS

P

O

Video

Sync

Sync

Horizontal

Vertical

CDE

P

O

B

A

Video

Sync

Sync

B

Green

Vertical

P

Q

R

S

O

Horizontal

Table 2-1. Timing Chart

Mode

Timing

fH (kHz)

A µsec

B µsec

C µsec

D µsec

E µsec

fV (Hz)

O msec

P msec

Q msec

R msec

S msec

Clock
Freq.
(MHz)

VGA2/70Hz

720 x 400

31.469

31.778

3.813

1.907

25.422

0.636

70.087

14.268

0.064

1.080

12.711

0.413

28.322

IBM VESA

VGA3/60Hz

640 x 480

31.469

31.778

3.813

1.907

25.422

0.636

59.940

16.683

0.064

1.048

15.253

0.318

25.175

640/85 Hz

640 x 480

43.269

23.111

1.556

3.810

5.222

17.778

85.008

13.333

0.080

0.427

12.800

0.027

36.000

800/85 Hz

800 x 600

53.674

18.631

1.138

2.702

14.222

0.569

85.061

11.756

0.056

0.503

11.179

0.019

56.250

1024/75 Hz
1024 x 768

(17”only )

60.023

16.660

1.219

2.235

13.003

0.203

75.029

13.328

0.050

0.466

12.795

0.017

78.750

1024/85 Hz

1024 x 768

68.677

14.561

1.016

2.201

10.836

0.508

84.997

11.765

0.044

0.524

11.183

0.015

94.500

1280 x 1024

1280/75 Hz

79.976

12.504

1.067

1.837

9.481

0.119

75.025

13.329

0.038

0.475

12.804

0.013

135.000

1280/85 Hz

1280 x 1024

91.146

10.971

0.016

1.422

8.127

0.406

85.024

11.761

0.033

0.483

11.235

0.011

157.500

1600/75 Hz

1600 x 1200

(19”only )

93.750

10.667

0.948

1.501

7.901

0.316

75.000

13.333

0.032

0.491

12.800

0.011

202.500

1600/85 Hz
1600 x 1200
(AQ19NS only )

106.250

9.412

0.837

1.325

6.972

0.279

85.000

11.765

0.028

0.433

11.294

0.009

229.500

Polarity
H.Sync

V.Sync

Remark

A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width

C : Back porch D : Active time Q : Back porch R : Active time

E : Front porch S : Front porch

Negative

Positive

Separate

Negative

Negative

Separate

Negative

Negative

Separate

Separate Sync

Positive

Positive

Separate

Positive

Positive

Separate

Positive

Positive

Separate

Positive

Positive

Separate

Positive

Positive

Separate

Sync-on-Green

Positive

Positive

Separate

Positive

Positive

Separate

2-2 AQ17HS/AQ17IS/AQ17NS

AQ19MS/AQ19IS/AQ19NS/AQ19FS

4 Alignment and Adjustments

This section of the service manual explains how to make permanent adjustments to the monitor.

4-1 Adjustment Conditions

Caution: Changes made without the Softjig are saved only to the user mode settings. As such, the

settings are not permanently stored and may be inadvertently deleted by the user.

4-1-1 Before Making Adjustments

4-1-1 (a) ORIENTATION

When servicing, always face the monitor to the
east.

4-1-1 (b) WARM-UP TIME

The monitor must be on for 30 minutes before
starting alignment. Warm-up time is especially
critical in color temperature and white balance
adjustments.

4-1-1 (c) SIGNAL

Analog, 0.7 Vp-p positive at 75 ohm, internal
termination
Sync: Separate/Composite
(TTL level negative/positive)

Sync-on-Green:
Composite sync 0.3 Vp-p negative
(Video 0.7 Vp-p positive)

4-1-1 (d) SCANNING FREQUENCY

Horizontal: 30 kHz to 96 kHz (Automatic)
Vertical: 50 Hz to 160 Hz (Automatic)

Unless otherwise specified, adjust at the
1024 x 768 mode (H: 68 kHz, V: 85 Hz) signals.

Refer to Table 2-1 on pages 2-2 and 2-3.

4-1-1 (e) HIGH VOLTAGE ADJUSTMENT

Signal: 1024 x 768 mode (68 kHz/85 Hz)
Display image: Full white
Contrast: Maximum
Brightness: Maximum
Limit: 26 kV ± 0.5 kV

(19”: 27 kV ± 0.5 kV)

Measure the hight voltage level at the anode cap.
High voltage should be within the limit as above.
If the high voltage needs adjustment use the
Softjig.

4-1-1 (f) G2 (SCREEN) VOLTAGE

The Screen Voltage is fixed in the firm so don’t
need to adjust the Screen voltage.

4-1-1 (g) CENTER RASTER

Adjust VR401 so that the back raster comes to the
center when you apply a signal of 91 kHz/85 Hz.

4-1-2 Required Equipment

The following equipment may be necessary for
adjustment procedures:

4-1-2 (a) DISPLAY CONTROL ADJUSTMENT

1. Non-metallic (–) screwdriver: 1.5 mm
Non-metallic (–) screwdriver: 3 mm

2. Philips (+) screwdriver: 1.5 mm

3. Non-metallic hexkey: 2.5 mm

4. Digital Multimeter (DMM), or
Digital Voltmeter (DVM)

5. Signal generator, or
Computer with a video board that uses the
ET-4000 chipset (strongly recommended if
using Samsung DM 200 software) and that
displays: 1280 x 1024 @ 85 Hz, or 1600 x 1200
@ 85 Hz (maximum).

6. Personal computer

4-1-2 (b) COLOR ADJUSTMENTS

1. All equipment listed in 4-1-2 (a), above

2. Color analyzer, or any luminance
measurement equipmen

4-1-3 After Making Adjustments

After finishing all adjustments, test the monitor in
all directions. If, for example, the monitor does not
meet adjustment specifications when facing north,
reposition the monitor to face east and readjust.
This time, try for an adjustment closer to the ideal
setting within the tolerance range. Test the unit
again in all directions. If the monitor again fails to
meet specifications in every direction, contact
your Regional After Service Center for possible
CRT replacement.

❇ Adjust the screen VR of FST so that the G2 (screen) voltage it is 540 ± 10V (AQ19FS)

AQ17HS/AQ17IS/AQ17NS
AQ19MS/AQ19IS/AQ19NS/AQ19FS

4-1

4 Alignment and Adjustments

4-2 Display Control Adjustments

4-2-1 Centering

Centering means to position the center point of
the display in the middle of the display area.
Horizontal size and position and vertical size and
position control the centering of the display.

Adjust the horizontal size and vertical size to their
optimal settings: 312 mm (H) x 234 mm (V).
1024 x 768 mode (68 kHz/85Hz)

Adjust the horizontal position and vertical
position to ≤ 4.0 mm of the center point of the
screen.

|A-B| ≤ 4.0 mm. |C-D| ≤ 4.0 mm.

C

DISPLAY AREA

A

D

Figure 4-3. Centering

4-2-1 (a) HORIZONTAL SIZE ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz/85 Hz
Display image: Crosshatch pattern
Brightness: Cut-off
Contrast: Maximum

Click on the << or >> box next to SIZE B+ to
adjust the horizontal size of the display pattern
to 312 mm (Tolerance: ± 3 mm) as the “H_SIZE”
is “60” on the OSD.

4-2-1 (b) VERTICAL SIZE ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz /85 Hz
Display image: Crosshatch pattern
Brightness: Cut-off
Contrast: Maximum

Click on the << or >> box next to V_SIZE to
adjust the vertical size of the display pattern to
234 mm. (Tolerance: ± 3 mm.)

4-2-1 (c) HORIZONTAL POSITION ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz/85 Hz
Display image: Crosshatch pattern
Brightness: Cut-off
Contrast: Maximum

Click on the << or >> box next to H_POSI to
center the horizontal image on the raster.

B

EDGE OF BEZEL

4-2-1 (d) VERTICAL POSITION ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz/85 Hz
Display image: Crosshatch pattern
Brightness: Cut-off
Contrast: Maximum

Click on the << or >> box next to V_POSI to
center the vertical image on the raster.

4-2-2 Linearity

Linearity affects the symmetry of images as they
appear on the screen. Unless each row or column
of blocks in a crosshatch pattern is of equal size,
or within the tolerances shown in Table 4-1 an
image appears distorted, elongated or squashed.

Horizontal Linearity = 2x x100

Vertical Linearity = 2x x100

Preset mode

Pre-load mode (48kHz~) ≤ 5% ≤ 10%

Pre-load mode (under 48kHz) ≤ 5% ≤ 14%

❈ Preset Mode : 68KHz / 85Hz

Pre-load Mode : Refer to Timing Chart

4-2-2 (a) HORIZONTAL LINEARITY ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz/85 Hz
Display image: Crosshatch pattern
Brightness: Cut-off
Contrast: Maximum

To adjust the Horizontal Linearity, refer to Table
4-1 for the tolerance range.

Click on the << or >> box next to H_LIN to
optimize the image.

(Horizontal x Vertical Size Table)

Horizantal 312 352

Vertical 234 264

X max-X min

X max+X min

Y max-Y min

Y max+Y min

Table 4-1

Adjacent Linearity

≤ 4% ≤ 8%

Table 4-2

17” 19”

Entire Linearity

4-2 AQ17HS/AQ17IS/AQ17NS

AQ19MS/AQ19IS/AQ19NS/AQ19FS

4-2-2 (b) VERTICAL LINEARITY ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz/85 Hz
Display image: Crosshatch pattern
Brightness: Cut-off
Contrast: Maximum

To adjust the Vertical Linearity, refer to Table 4-1
for the tolerance range.

Use control bar after selecting “V_LINEARITY
BAL” in left menu to optimize the image.

4-2-3 Trapezoid Adjustment

CONDITIONS

Scanning frequency: 68 kHz/85 Hz
Display image: Crosshatch pattern
Brightness: Cut-off
Contrast: Maximum

Use control bar after selecting “TRAPEZOID” in
left menu to make the image area rectangular.

| A - B | < 5 mm

A

A

4 Alignment and Adjustments

4 mm

Figure 4-6. Parallelogram

4-2-6 Side Pincushion Adjustment

CONDITIONS

Scanning frequency: 68 kHz/85 Hz
Display image: Crosshatch pattern
Brightness: Cut-off
Contrast: Maximum

Use control bar after selecting “PINCUSHION” in
left menu to straighten the sides of the image area.

| C1 |, | C2 | ≤ 2.0 mm, | D1 |, | D2 | ≤ 2.0 mm.

C2

B

Figure 4-4. Trapezoid

B

4-2-4 Pinbalance Adjustment

CONDITIONS

Scanning frequency: 68 kHz/85 Hz
Display image: Crosshatch pattern
Brightness: Cut-off
Contrast: Maximum

| D1 |, | D2 | ≤ 2.0 mm

D1 D2 D1

Figure 4-5. Pinbalance

Use control bar after selecting “PINBALANCE” in
left menu to optimize the image.

4-2-5 Parallelogram Adjustment

CONDITIONS

Scanning Frequency: 68 kHz/85 Hz
Display image: Crosshatch pattern
Brightness: Cut-off
Contrast: Maximum

Use control bar after selecting “PARALLEL” in
left menu to make the image area rectangular.

D2D1

C1

Figure 4-7. Pincushion

4-2-7 Degauss

No adjustments are available for the degaussing
circuit. The degaussing circuit can effectively
function only once per 30 minutes.

4-2-8 Save the Data

To save the adjustment data for factory
frequencys, press FACTORY SAVE.

4-2-9 To Delete the User Mode Data

To delete the adjustment data from the user
modes, click “@4: USER DELETE” in right menu.

AQ17HS/AQ17IS/AQ17NS
AQ19MS/AQ19IS/AQ19NS/AQ19FS

4-3

4 Alignment and Adjustments

4-3 Color Adjustments

4-3-1 Color Coordinates (Temperature)

Color temperature is a measurement of the
radiant energy transmitted by a color. For
computer monitors, the color temperature refers
to the radiant energy transmitted by white. Color
coordinates are the X and Y coordinates on the
chromaticity diagram of wavelengths for the
visible spectrum.

CONDITIONS

Measurement instrument: Color analyzer
Scanning frequency: 68 kHz/85 Hz
Display Size : 312 (H) x 234 (V)
Display image: White flat field at

center of display area
Brightness: Cut-off
Contrast: Maximum

PROCEDURE

Use the directions in sections 4-3-2 through 4-3-4
to adjust the color coordinates for:
9300K to x = 0.283 ± 0.02, y = 0.298 ± 0.02
6500K to x = 0.313 ± 0.02, y = 0.329 ± 0.02
5000K to x = 0.346 ± 0.02, y = 0.359 ± 0.02

4-3-2 (b) G-GAIN ADJUSTMENT

1/3H-1/2H

FRONT BEZEL OPENING

1/3V-1/2V

BACK RASTER

GREEN WINDOW

Figure 4-8. Green Box Pattern

CONDITIONS

Scanning frequency: 68 kHz/85 Hz
Display image: Green box pattern
Brightness: Cut-off
Contrast: Maximum

1. Click on the << or >> box next to G_GAIN to
adjust the brightness of the Green Gain to
40 ± 1 ft-L.

2. Click on the << or >> box next to “BM
Contrast” to adjust the Brightness of the High
Light Gain to 75ft-L when the High Light
function was (“BM contrast” Menu is in the
“Extra Menu”) activated with Maximum size.

4-3-2 Color Adjustments for 9300K

4-3-2 (a) BACK RASTER COLOR ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz/85 Hz
Display image: Back raster pattern
Brightness: Cut-off
Contrast: Maximum

1. Select COLOR CHANNEL 1 to control the
color for 9300K.

2. Adjust the luminance of the back raster to
between 0.5 to 0.7ft-L using the “GREEN
CUTOFF” controls.

3. Use control bar after selecting “BLUE
CUTOFF” in left menu to set the “y”
coordinate to 0.298 ± 0.015

4. Use control bar after selecting “RED
CUTOFF” in left menu to 0.283 ± 0.015

* If color values would not be matched desirable

values, repeat sequence 3 and 4 after readjusting
“GREEN CUTOFF” control a little different.

4-3-2 (c) WHITE BALANCE ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz/85 Hz
Display image: Full white pattern
Brightness: Cut-off
Contrast: Maximum

FRONT BEZEL OPENING

BACK RASTER

WHITE WINDOW

Figure 4-9. Full White Pattern

1. Click on the << or >> boxes next to R_GAIN
and B_GAIN to make the video white.
(For 9300K color adjustment:
x = 0.283 ± 0.02, y = 0.298 ± 0.02.)

Note: Do not touch the G_GAIN controls.

2. Check the ABL. If it is not within the
specifications (30 ± 1 ft-L), use the ABL
controls to adjust it.

3. Select COLOR FACTORY SAVE to save the
data.

4-4 AQ17HS/AQ17IS/AQ17NS

AQ19MS/AQ19IS/AQ19NS/AQ19FS

4 Alignment and Adjustments

Luminance Table (9300K) 4-3

17HS/IS/NS

Without ABL 40ft-L 36ft-L 36ft-L

Without ABL 31ft-L 30ft-L 30ft-L

Without ABL
(High Light is Activated)

75ft-L 75ft-L 65ft-L

19MS/NS/FS

19IS

4-3-2 (d) WHITE BALANCE ADJUSTMENT VERIFICATION

CONDITIONS

Scanning frequency: 68 kHz/85 Hz
Display image: Back raster pattern
X-Y Coordinates: x = 0.283 ± 0.02,

y = 0.298 ± 0.02
Raster Luminance 0.3 ~ 1ft-L
ABL Luminance 30 ± 1 ft-L
Brightness: Cut-off
Contrast: Maximum

1. Check whether the color coordinates of the

back raster satisfy the above spec.

If they do not, return to 4-3-2 (a) and readjust
all settings.

2. Display a full white pattern.

4-3-3 (b) G-GAIN ADJUSTMENT

This procedure is the same as that for 9300K, refer
to the procedure on page 4-5.

You must adjust the Brightness of Green gain to
39 ± 1ft-L.

4-3-3 (c) WHITE BALANCE ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz/85 Hz
Display image: Full white pattern
Brightness: Cut-off
Contrast: Maximum

1. Click on the << or >> boxes next to R_GAIN
and B_GAIN to make the video white.
(For 6500K color adjustment:
x = 0.313 ± 0.02, y = 0.329 ± 0.02.)

2. Refer to the procedure for 9300K, section
4-3-2 (c) steps 2 and 3.

4-3-3 (d) WHITE BALANCE ADJUSTMENT VERIFICATION

Refer to the procedure for 9300K, section 4-3-2 (d).

Luminance Table (6500K) 4-4

Note: Do not touch the G_GAIN controls.

3. Adjust the Contrast Control on the monitor so
that the luminance of the video is about 5 ft-L.

4. Check whether the white coordinates of the
video meet the above coordinates spec.

5. Adjust the Contrast Control again so that the
luminance of the video is about 20 ft-L.

6. Check whether the white coordinates of the
video satisfies the above spec.

If they do not, return to 4-3-2 (a) and readjust
all settings.

4-3-3 Color Adjustments for 6500K

4-3-3 (a) BACK RASTER COLOR ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz/85 Hz
Display image: Back raster pattern
Brightness: Cut-off
Contrast: Maximum

1. Select COLOR CHANNEL 2 to control the
color for 6500K.

2. Adjust the luminance of the back raster to
between 0.5 to 0.7 ft-L using the G_CUT
controls.

3. Click on the << or >> boxes next to R_CUT
and B_CUT to adjust the R-Bias to x = 0.313 ±

0.02 and the B-Bias to y = 0.329 ± 0.02.

17HS/IS/NS 19NS/FS/IS

Without ABL 39ft-L 34ft-L

With ABL 30ft-L 29ft-L

4-3-4 Color Adjustments for 5000K

4-3-4 (a) BACK RASTER COLOR ADJUSTMENT

CONDITIONS

Scanning frequency: 68 kHz/85 Hz
Display image: Back raster pattern
Brightness: Cut-off
Contrast: Maximum

1. Select COLOR CHANNEL 3 to control the
color for 5000K.

2. Adjust the luminance of the back raster to
between 0.5 to 0.7 ft-L using the G_CUT
controls.

3. Click on the << or >> boxes next to R_CUT
and B_CUT to adjust the R-Bias to x = 0.346 ±

0.02 and the B-Bias to y = 0.359 ± 0.02.

4-3-4 (b) G-GAIN ADJUSTMENT

This procedure is the same as that for 9300K, refer
to the procedure on page 4-5.

Adjust the brightness of the G_GAIN less 2 ft-L
than brightness of procedure for 9300K.

4-3-4 (c) WHITE BALANCE ADJUSTMENT

AQ17HS/AQ17IS/AQ17NS
AQ19MS/AQ19IS/AQ19NS/AQ19FS

4-5

4 Alignment and Adjustments

CONDITIONS

Scanning frequency: 68 kHz/85 Hz
Display image: Full white pattern
Brightness: Cut-off
Contrast: Maximum

1. Click on the << or >> boxes next to R_GAIN
and B_GAIN to make the video white.
(For 5000K color adjustment:
x = 0.346 ± 0.02, y = 0.359 ± 0.02.)

2. Refer to the procedure for 9300K, section
4-3-2 (c) steps 2 and 3.

Luminance Table (6000K) 4-5

17HS/IS/NS 19NS/FS/IS

Without ABL 38ft-L 33ft-L

With ABL 30ft-L 28ft-L

4-3-4 (d) WHITE BALANCE ADJUSTMENT VERIFICATION

Refer to the procedure for 9300K, section 4-3-2 (d).

4-3-5 Luminance Uniformity Check

Luminance is considered uniform only if the ratio
of lowest to highest brightness areas on the screen
is not less than 7.5:10.

CONDITIONS

Scanning frequency: 68 kHz/85 Hz

(1024 x 768)
Display image: White flat field
Display size 312 (H) x 234 (V)
Brightness: Cut off point
Contrast: Maximum

PROCEDURE

Measure luminance at nine points on the display
screen (see figure below).

PROCEDURE

1. Adjust the Focus VR on the FBT to display the
sharpest image possible.

2. Use Locktite to seal the Focus VR in position.

4-3-7 Color Purity Adjustment

Color purity is the absence of undesired color.
Conspicuous mislanding (unexpected color in a
uniform field) within the display area shall not be
visible at a distance of 50 cm from the CRT
surface.

CONDITIONS

Orientation: Monitor facing east
Scanning frequency: 68 kHz/85 Hz
Display image: White flat field
Luminance: Cut off point at the center

of the display area

Note: Color purity adjustments should only be

attempted by qualified personnel.

PROCEDURE

For trained and experienced service technicians
only.

Use the following procedure to correct minor
color purity problems:

1. Make sure the display is not affected by
external magnetic fields.

2. Very carefully break the glue seal between the
2-pole purity convergence magnets (PCM), the
band and the spacer.

3. Make sure the spacing between the PCM
assembly and the CRT stem is 29 mm ± 1 mm.

4. Display a green pattern over the entire display
area.

5. Adjust the purity magnet rings on the PCM
assembly to display a pure green pattern.
(Optimum setting: x = 0.295 ± 0.015,
y = 0.594 ± 0.015)

6. Repeat steps 4 and 5 using a red pattern and
then again, using a blue pattern.

Figure 4-10 Luminance Uniformity Check Locations

4-3-6 Focus Adjustment

CONDITIONS

Red: x = 0.620 ± 0.015 y = 0.334 ± 0.015

Green: x = 0.289 ± 0.015 y = 0.595 ± 0.015

Blue: x = 0.153 ± 0.015 y = 0.072 ± 0.015

Table 4-6. Color Purity Tolerances

Scanning frequency: 68 kHz/85 Hz
Display image: “H” character pattern
Brightness: Cut off point
Contrast: Maximum

(For 9300K color adjustment: x = 0.283 ± 0.02, y = 0.298 ± 0.02)

7. When you have the PCMs properly adjusted,
carefully glue them together to prevent their
movement during shipping.

4-6 AQ17HS/AQ17IS/AQ17NS

AQ19MS/AQ19IS/AQ19NS/AQ19FS

!!!!!

!

0

7 Electrical Parts List

7-1-1 AQ17** Main PCB Parts

Loc. No. Code No. Description Specification Remarks

C416 2306-000147 C-FILM,MPPF 1uF,5%,250V,BK,26x24x15,22.5mm
C602 2305-001049 C-FILM,MPEF 1000nF,10%,275V,BK,31x23x13mm,27.5
C607 2401-003391 C-AL 220uF,20%,450V,GP,BK,25x50,10
C701 2301-001314 C-FILM,MPPF 470NF,10%,275V,BK,25X11.5X21MM,22.5
CIS 6501-000004 CABLE TIE DA-80,T1,W2.5,L80,NTR,NYLON66 SNA
CIS BH72-60765A GUIDE-POWER CSM92*,ABS+PC,5V,IV16,T3,- SNA
CIS BH68-00001A LABEL/MARK-CDT ART-PAPER 100G,-,WHT,BLK,-,ALL,CDT SNA
CIS BH46-00003H MICOM-S/W,AQUILA AQUILA17,-,-,-,-,-,- SNA
CIS BH73-60304C RUBBER-SUPPORT DP15LT,CR V0,GRAY,-,14*7*10,-,- SNA
CIS BH72-00296A SHAFT-POWER PN19LT,ABS+PC,IV16,-,5V,-,-,- SNA
CIS BH72-00351A SHEET-LMF AQ19FS,AL+PET,-,-,-,-,-,- SNA
CIS BH71-00141B SHIELD-BOTTOM AQ19FS,SECC ,T1.0,-,DELL,- SNA
CIS 0202-001046 SOLDER-WIRE FLUX CF-110VH-2A,-,-,-,- SNA
CIS 0202-001172 SOLDER-WIRE FLUX RS-107,RS60,D1.2,SN60/PB40,- SNA
CIS 0202-001044 SOLDER-WIRE. S63S-W3.0,S63S,D3,63Sn/37Pb,- SNA
CIS 0203-001199 TAPE-KRAFT #53110,T0.1,W6,L2000M,BRN SNA
CIS 0203-001200 TAPE-PAPER #53128,T0.15,W5.5,L2000M,BEIGE SNA
CIS 0203-001201 TAPE-PAPER #FB-300,T0.16,W6,L2000M,R/BLU SNA
CIS 0204-001095 THINNER #4520,-,-,- SNA
CN201 3711-004352 CONNECTOR-HEADER BOX,15P,1R,2MM,STRAIGHT,SN SNA
CN201_ASSY BH39-00060A CBF-HARNESS
CN202 3711-004351 CONNECTOR-HEADER NOWALL,16P,1R,2.54MM,STRAIGHT,SN SNA
CN204 3711-004379 CONNECTOR-HEADER BOX,4P,1R,2MM,STRAIGHT,SN SNA
CN205 3711-004484 CONNECTOR-HEADER BOX,5P,1R,2mm,STRAIGHT,SN SNA
CN205_ASSY BH39-00362A WIRE HARNESS
CN211 3711-004484 CONNECTOR-HEADER BOX,5P,1R,2mm,STRAIGHT,SN SNA
CN211+CN212 BH39-00368A CBF HARNESS
CN212 3711-004484 CONNECTOR-HEADER BOX,5P,1R,2mm,STRAIGHT,SN SNA
CN401 3711-003989 CONNECTOR-HEADER NOWALL,4P,1R,8mm,STRAIGHT,SN SNA
CORE_FBT 3301-000130 CORE-FERRITE AC,23.5x9.4x12.6mm,1500,2800G SNA
D402 0402-001441 DIODE-RECTIFIER -,40V,3A,DO-201AD,BK
D505 0402-001295 DIODE-RECTIFIER GUR460L-5700,600V,4A,DO-201AD,BK
D507 0402-001295 DIODE-RECTIFIER GUR460L-5700,600V,4A,DO-201AD,BK
D601 0402-001227 DIODE-BRIDGE D3SBA60,600V,2.3A,SIP-4,BK
D647 0402-000250 DIODE-RECTIFIER RG4C,1000V,1A,­EY599 BH39-00232A CBF-HARNESS
FG601 3601-000455 FUSE-CARTRIDGE 250V,4A,TIME-LAG,CERAMIC,5.2x20mm
HS301 6502-000132 CABLE CLAMP DAWS-1NE,ID11,L21.0,NTR,NYLON66 SNA
HS402_1 6502-000135 CABLE CLAMP DAWS-2NA,ID10,-,NTR,NYLON66 SNA
HS504 6502-000001 CABLE CLAMP DAWH-5NB,D15,L35,NTR,NYLON66 SNA
IC201 0903-001237 IC-MICROCONTROLLER
IC201_SOCKET 3704-001071 SOCKET-IC 42P,DIP,SN,1.778mm
IC250 1204-001697 IC-DEF. PROCESSOR
IC403 BH13-00009A IC-H/V CONVERGENCE
IC620 0604-001018 PHOTO-COUPLER DAR-TR,63-125%,200mW,DIP-4,ST SNA
JW01 BH39-40306D CBF-HARNESS ,80MM,BLK,1015,AWG22,-,-,-,-,­L402 BH27-20345J COIL-HORIZ.CENTER -,3.5mH,-,OB6*30-1HHA,-,-,-,-,6.0ohm,-,-,-,BULK
L403 BH26-00001A TRANS-H.LINEARITY
L503 BH27-00037A COIL-CHOKE 3.5uH,+/-10%,12*15,BULK,-,­L601 BH27-00025A COIL-LINE FILTER
L701 BH27-00053A COIL CHOKE

15P/15P,180MM,WHT/BLU/RED/BLK,UL1007,AWG26,SMH200-15

AQ19FS,UL1007#26,UL/CSA,5P/5P,320MM,WHT,AWG26,SMH200-05,-,-,-,-,-,-,-,-

AQ17IS,U2464#26-4C,U2464,80`C,300V,5P/5P,240MM,BLK,26AWG*4,SMH200-05,SMH200-05,B

DP17MO,UL1032,UL/CSA,1P,290MM,RED,AWG22,YHF800-1,-,-,-,-,-,-,-,CBF-CONN ASS’Y

ST72774,8BIT,DIP,42P,-,24MHZ,ST,HCMOS,PLASTIC,5.5V,-,0TO+70C,1KB,60KB,8BIT,-,IC-

SNA

TDA9112,DIP,32P,350MIL,PLASTIC,13.2V,-,0to+70C,ST,DEF.PROCESSOR
PG17/19,AN5452,SIP,12P,H/V CONVERGENCE,-,1171MW

-,-,5P,-,-,5.0UH/47.5MH,-, ,-,19.0,-,YL-81,DR1420,C:6.0,-,-,BULK,-

-,24.0mH,-,SQE-2828,65.5Ts,PHENOLIC,-,-,0.20 ohm,-,-,-,BK
TO-2012,195uH,-,20.20*12.57*6.35,65Ts,PHENOLIC,-,-,0.08ohm,17.0*32.0*10.0,-,-,-

AQ17HS/AQ17IS/AQ17NS

7-1

AQ19MS/AQ19IS/AQ19NS/AQ19FS

!!!!!!!

!

7 Electrical Parts List

Loc. No. Code No. Description Specification Remarks

LC601 2901-001173 FILTER-EMI AC LINE
M/PCB+SH/BTM

6003-000010 SCREW-TAPTITE BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 SNA

250V,3A,UL/CSA/TUV/SEMKO,2200pF,32x39.7x23.4mm,BK,-

OP1 0601-001147 LED ROUND,GRN,4.75mm,565nm SNA
POS601 1404-000002 THERMISTOR-PTC 9ohm,20%,-,-,TR,RECT,­Q401 0505-001357 FET-SILICON SKS4N20,N,200V,3A,1.3OHM,27W,TO-220F
Q407 0505-001305 FET-SILICON SKS10N20,N,200V,6.9A,0.36OHM,39W,TO-220F
R400 2003-000473 R-METAL OXIDE(S) 10ohm,5%,3W,AA,TP,6x16mm
R407 2003-000423 R-METAL OXIDE(S) 1.2ohm,5%,3W,AA,TP,6x16mm
R516 2006-001066 R-CEMENT 33OHM,5%,7W,CS,BK,9X10X54MM
R608 2003-000756 R-METAL OXIDE(S) 33OHM,5%,7W,CS,BK,9X10X54MM
RL601 3501-001111 RELAY-POWER 12Vdc,250mW,5A,1FormA,15mS,5mS
SH/BNC+SH/BTM
SH/LMF+SH/BTM

6003-000010 SCREW-TAPTITE BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 SNA

6003-000010 SCREW-TAPTITE BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 SNA
SW1 3403-001116 SWITCH-PUSH 30VDC,0.1A,2C2P,SELF LOCK,­T401 BH26-00094A TRANS HORIZ.DRIVE
T402 BH26-00093A TRANS-H-.PULSE
T501 BH26-00131A TRANS FBT
T502 BH26-00086A TRANS-FOCUS
T601 BH26-00128A TRANS POWER
T620 BH26-30302S TRANS-SYNC.
T701 BH27-00081A COIL-PFC

EI-2218,PN19,8P,2.5mH,-,-,78uH,-,-,0.6ohm/0.12ohm,-,PL3,DMR30,EI-2218,18.0uH,-,­EI-2820,PN19,10P,1.5mH,-,-,130uH,-,-,1.2ohm/0.32ohm,-,PL3,DMR30,EI-2820,70uH MAX
FQM21A010,AQ19IS,80.0UH,SM-19C,FUR3757(SM19C),0.145,76.5V,15P,-10~ +50,BK,27KV
EE1916,-,5P,1.7mH MIN,-,-,255mH MIN,-,-,0.85ohm/32.0ohm,-,EE1916(PL3,SL-2),EE19

*

ER-3942(18P),AQ17IS,130UH,18P,AC90 ~240V,-,-,-,-,-,PL3,DMR30,EER 39*42,0.1OHM MA

-,-,-,-,-,3-1(250UH),4-6(250UH,-,-,-,0.13OHM,-,SB-5S,UU1116,-,-,-,B,-

EER-2828,135uH,10%,EER2828(PL3,J2A-1),USTC0.25*932Ts,PHELOLIC,-, GREEN COLOR TAP
TH601 1404-001076 THERMISTOR-NTC 8ohm,15%,-,17mW/C,TP
VR401 2103-001049 VR-SEMI 100ohm,30%,1/5W,SIDE
BD201 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500,2375G SNA
BD280 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500,2375G SNA
BD401 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500,2375G SNA
BD532 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500,2375G SNA
BD602 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500,2375G SNA
BD603 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500,2375G SNA
BD604 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500,2375G SNA
BD651 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500,2375G SNA
BD652 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500,2375G SNA
BD653 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500,2375G SNA
C201 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP,8x3,5
C202 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5
C203 2201-000389 C-CERAMIC,DISC 0.022nF,5%,50V,NP0,TP,5x3,5
C204 2201-000389 C-CERAMIC,DISC 0.022nF,5%,50V,NP0,TP,5x3,5
C208 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3
C209 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5
C210 2401-001509 C-AL 47uF,20%,16V,GP,TP,5x7mm,5
C211 2201-000017 C-CERAMIC,DISC 1nF,10%,50V,Y5P,TP,5x3.5,5
C212 2201-000144 C-CERAMIC,DISC 0.1nF,5%,50V,NP0,TP,8.5x3,5
C213 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3
C214 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3
C216 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V,TP,2.3X3.
C220 2401-001281 C-AL 4.7uF,20%,50V,WT,TP,5x11,5
C250 2202-000654 C-CERAMIC,MLC-RADIAL 100nF,10%,50V,X7R,TP,5.1x6.6x3.2mm,5
C251 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mm
C252 2202-002149 C-CERAMIC,MLC-RADIAL 0.82NF,2%,50V,NPO,TP,5.1X3.2X6.4MM,5
C253 2201-000163 C-CERAMIC,DISC 10nF,+80-20%,50V,Y5V,TP,7x3,2.5
C254 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5
C255 2305-000237 C-FILM,MPEF 1uF,5%,63V,TP,7.5x15.5mm,5mm
C256 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mm

7-2 AQ17HS/AQ17IS/AQ17NS

AQ19MS/AQ19IS/AQ19NS/AQ19FS

!

!

7 Electrical Parts List

Loc. No. Code No. Description Specification Remarks

C257 2301-000188 C-FILM,PEF 1nF,5%,100V,TP,10.5x12.5x6.5,5
C258 2201-000132 C-CERAMIC,DISC 0.1nF,10%,500V,Y5P,TP,6.5x3,5
C259 2401-000050 C-AL 10uF,20%,16V,GP,TP,5x11,2.5
C260 2202-000654 C-CERAMIC,MLC-RADIAL 100nF,10%,50V,X7R,TP,5.1x6.6x3.2mm,5
C264 2401-000031 C-AL 47uF,20%,16V,GP,TP,5x11,5
C265 2305-000412 C-FILM,MPEF 470nF,5%,63V,TP,-,5mm
C266 2301-000168 C-FILM,PEF 150nF,5%,100V,TP,11.5x19mm,7.5
C268 2401-003484 C-AL 10uF,20%,100V,LZ,TP,6.3X11,5
C269 2401-000480 C-AL 10uF,20%,50V,GP,TP,5x11,5
C270 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP,8x3,5
C271 2401-000025 C-AL 100uF,20%,16V,GP,TP,6.3x11,5
C280 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3
C281 2401-000480 C-AL 10uF,20%,50V,GP,TP,5x11,5
C283 2201-000144 C-CERAMIC,DISC 0.1nF,5%,50V,NP0,TP,8.5x3,5
C284 2201-000144 C-CERAMIC,DISC 0.1nF,5%,50V,NP0,TP,8.5x3,5
C285 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3
C301 2401-000142 C-AL 1000uF,20%,16V,WT,TP,10x20,5
C302 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3
C303 2401-002274 C-AL 220uF,20%,35V,WT,TP,10x12.5,5
C304 2401-000597 C-AL 1uF,20%,50V,GP,TP,4x7mm,1.5mm
C305 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mm
C306 2305-000237 C-FILM,MPEF 1uF,5%,63V,TP,7.5x15.5mm,5mm
C307 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm,5
C308 2401-000142 C-AL 1000uF,20%,16V,WT,TP,10x20,5
C309 2301-000294 C-FILM,PEF 56nF,5%,100V,TP,9.5x12.5mm,5mm
C310 2301-000287 C-FILM,PEF 5.6nF,5%,100V,TP,10.5x12.5x6.5
C312 2305-000237 C-FILM,MPEF 1uF,5%,63V,TP,7.5x15.5mm,5mm
C401 2401-000049 C-AL 47uF,20%,100V,WT,TP,10x16,5
C402 2201-000132 C-CERAMIC,DISC 0.1nF,10%,500V,Y5P,TP,6.5x3,5
C403 2201-000291 C-CERAMIC,DISC 1nF,10%,500V,Y5P,TP,7.5x3.5,5
C404 2301-000020 C-FILM,PEF 27nF,5%,100V,TP,7.3x4x12.5mm,5
C405 2305-000624 C-FILM,MPEF 330nF,10%,100V,TP,-,5mm
C406 2305-000624 C-FILM,MPEF 330nF,10%,100V,TP,-,5mm
C407 2305-000624 C-FILM,MPEF 330nF,10%,100V,TP,-,5mm
C408 2303-001022 C-FILM,PPF 2nF,5%,2.5KV,TP,23x12x19mm,7.5
C409 2303-001022 C-FILM,PPF 2nF,5%,2.5KV,TP,23x12x19mm,7.5
C410 2201-000291 C-CERAMIC,DISC 1nF,10%,500V,Y5P,TP,7.5x3.5,5
C411 2301-001259 C-FILM,MPPF 100nF,5%,400V,TP,19x8x16,7.5mm
C412 2305-001041 C-FILM,MPEF 220nF,5%,63V,TP,7.5x4.5x13.5,5
C413 2301-001259 C-FILM,MPPF 100nF,5%,400V,TP,19x8x16,7.5mm
C414 2306-000137 C-FILM,MPPF 180nF,5%,250V,TP,19x16.5x8,7.5
C415 2301-001194 C-FILM,MPPF 470nF,5%,250V,TP,18x16x8,7.5
C417 2306-000119 C-FILM,MPPF 100nF,5%,250V,TP,19x14.5x6.5,7
C418 2301-001249 C-FILM,MPPF 68nF,5%,400V,TP,19x7x15mm,7.5
C433 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3
C440 2401-003080 C-AL 3.3UF,20%,50V,BP,TP,5X11,2.5
C450 2401-000025 C-AL 100uF,20%,16V,GP,TP,6.3x11,5
C451 2401-002299 C-AL 4.7uF,20%,50V,GP,TP,5x7,5
C452 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mm
C453 2202-000561 C-CERAMIC,MLC-RADIAL 680pF,5%,50V,NPO,TP,5.1x3.2,5.
C454 2201-000017 C-CERAMIC,DISC 1nF,10%,50V,Y5P,TP,5x3.5,5
C456 2303-000011 C-FILM,PPF 1nF,5%,100V,TP,14x11.5mm,7.5mm
C457 2201-000602 C-CERAMIC,DISC 0.56nF,5%,50V,SL,TP,10x3.5,5

AQ17HS/AQ17IS/AQ17NS

7-3

AQ19MS/AQ19IS/AQ19NS/AQ19FS

!!!

!

7 Electrical Parts List

Loc. No. Code No. Description Specification Remarks

C458 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V,TP,2.3X3.
C459 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3
C460 2301-000020 C-FILM,PEF 27nF,5%,100V,TP,7.3x4x12.5mm,5
C461 2201-000012 C-CERAMIC,DISC 0.22nF,10%,1kV,Y5P,TP,6.3x5,5
C462 2301-000020 C-FILM,PEF 27nF,5%,100V,TP,7.3x4x12.5mm,5
C463 2401-001548 C-AL 47uF,20%,25V,WT,TP,5x11,5
C464 2301-001322 C-FILM,PPF 33nF,5%,250V,TP,17.5x5x11mm,7.5
C465 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5
C466 2401-003525 C-AL 10uF,20%,250V,LZ,TP,10X20,5
C467 2301-000102 C-FILM,PEF 1.2nF,5%,100V,TP,5.4x10mm,5mm
C468 2201-000131 C-CERAMIC,DISC 0.1nF,10%,2kV,Y5P,TP,6.3x5,5
C501 2301-000294 C-FILM,PEF 56nF,5%,100V,TP,9.5x12.5mm,5mm
C502 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mm
C503 2401-001378 C-AL 470uF,20%,16V,WT,TP,10x20,5
C504 2401-000292 C-AL 100uF,20%,16V,WT,TP,8x11.5mm,5
C505 2201-000163 C-CERAMIC,DISC 10nF,+80-20%,50V,Y5V,TP,7x3,2.5
C506 2305-001041 C-FILM,MPEF 220nF,5%,63V,TP,7.5x4.5x13.5,5
C507 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP,8x3,5
C508 2401-000031 C-AL 47uF,20%,16V,GP,TP,5x11,5
C509 2401-000031 C-AL 47uF,20%,16V,GP,TP,5x11,5
C510 2301-000013 C-FILM,PEF 4.7nF,5%,100V,TP,10.5x12.5x6.5
C511 2303-000147 C-FILM,PPF 1NF,5%,2KV,TP,23X13X8MM,7.5
C512 2401-001576 C-AL 47uF,20%,50V,GP,TP,8x11.5,5
C513 2401-000638 C-AL 2.2uF,20%,350V,WT,TP,10x12.5mm
C514 2201-000325 C-CERAMIC,DISC 2.2nF,10%,500V,Y5P,TP,9.5x4,5
C516 2401-000771 C-AL 220uF,20%,100V,WT,TP,16x25,7.5
C520 2301-001027 C-FILM,PEF 15nF,10%,250V,TP,9.5x12x4.5,5m
C530 2401-000638 C-AL 2.2uF,20%,350V,WT,TP,10x12.5mm
C531 2401-000026 C-AL 3.3UF,20%,50V,GP,TP,5X11,5
C532 2301-001480 C-FILM,MPEF 2000NF,5%,100V,TP,17X16.5X9.5,7.5
C533 2305-000665 C-FILM,MPEF 100nF,5%,63V,TP,7.5x4.0x5.0mm,
C535 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5
C536 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP,8x3,5
C540 2201-000285 C-CERAMIC,DISC 1nF,10%,1kV,Y5P,TP,8x5,5
C550 2201-000144 C-CERAMIC,DISC 0.1nF,5%,50V,NP0,TP,8.5x3,5
C551 2301-000168 C-FILM,PEF 150nF,5%,100V,TP,11.5x19mm,7.5
C552 2305-000004 C-FILM,MPEF 220nF,10%,100V,TP,12.7x16,5mm
C559 2201-000129 C-CERAMIC,DISC 0.1nF,10%,1kV,Y5P,TP,7x4,5
C562 2401-001576 C-AL 47uF,20%,50V,GP,TP,8x11.5,5
C598 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5
C599 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5
C603 2201-000023 C-CERAMIC,DISC 2.2nF,20%,125V,Y5U,TP,11x7,5
C604 2201-000023 C-CERAMIC,DISC 2.2nF,20%,125V,Y5U,TP,11x7,5
C605 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5
C608 2401-000015 C-AL 33uF,20%,50V,WT,-,6.3x11mm,2.5
C609 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3
C610 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5
C611 2201-000012 C-CERAMIC,DISC 0.22nF,10%,1kV,Y5P,TP,6.3x5,5
C612 2201-000129 C-CERAMIC,DISC 0.1nF,10%,1kV,Y5P,TP,7x4,5
C613 2201-000023 C-CERAMIC,DISC 2.2nF,20%,125V,Y5U,TP,11x7,5
C614 2201-000023 C-CERAMIC,DISC 2.2nF,20%,125V,Y5U,TP,11x7,5
C620 2401-000613 C-AL 1uF,20%,50V,WT,TP,5x11,5
C621 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm,5

7-4 AQ17HS/AQ17IS/AQ17NS

AQ19MS/AQ19IS/AQ19NS/AQ19FS

!!!

!

7 Electrical Parts List

Loc. No. Code No. Description Specification Remarks

C622 2301-000013 C-FILM,PEF 4.7nF,5%,100V,TP,10.5x12.5x6.5
C624 2301-000016 C-FILM,PEF 22nF,5%,100V,TP,7.2x4.5x9.0mm,
C625 2401-000025 C-AL 100uF,20%,16V,GP,TP,6.3x11,5
C627 2301-000004 C-FILM,PEF 2.2nF,5%,100V,TP,5.5X10X2.9,5m
C628 2301-000174 C-FILM,PEF 15nF,5%,100V,TP,7.2x4.0x7.5mm,
C629 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5
C641 2401-000142 C-AL 1000uF,20%,16V,WT,TP,10x20,5
C642 2401-000142 C-AL 1000uF,20%,16V,WT,TP,10x20,5
C643 2401-001378 C-AL 470uF,20%,16V,WT,TP,10x20,5
C644 2401-000770 C-AL 220uF,20%,100V,WT,TP,13*25,5mm
C645 2401-001422 C-AL 470uF,20%,35V,WT,TP,12.5x25,5
C646 2401-000040 C-AL 47uF,20%,250V,WT,TP,16x25mm,7.
C649 2201-000551 C-CERAMIC,DISC 0.47nF,10%,1kV,Y5P,TP,6.3x5,5
C650 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5
C651 2202-002008 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,50V,Y5V,TP,2.3X3.
C652 2401-000010 C-AL 220uF,20%,16V,GP,-,6.3x11mm,2.
C653 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP,8x3,5
C654 2401-000142 C-AL 1000uF,20%,16V,WT,TP,10x20,5
C655 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mm
C656 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3
C702 2305-001041 C-FILM,MPEF 220nF,5%,63V,TP,7.5x4.5x13.5,5
C703 2201-000602 C-CERAMIC,DISC 0.56nF,5%,50V,SL,TP,10x3.5,5
C705 2301-000188 C-FILM,PEF 1nF,5%,100V,TP,10.5x12.5x6.5,5
C706 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3
C708 2401-000970 C-AL 22uF,20%,50V,WT,TP,5x11,5
C710 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5
CIS 0203-001199 TAPE-KRAFT #53110,T0.1,W6,L2000M,BRN SNA
CIS 0203-001200 TAPE-PAPER #53128,T0.15,W5.5,L2000M,BEIGE SNA
CIS 0203-001201 TAPE-PAPER #FB-300,T0.16,W6,L2000M,R/BLU SNA
CN209 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK SNA
CN210 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK SNA
CN409 3711-000197 CONNECTOR-HEADER 1WALL,3P,1R,2.5mm,STRAIGHT,SN SNA
CN414 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK SNA
CN415 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK SNA
CN420 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK SNA
CN421 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK SNA
CN601 3711-000217 CONNECTOR-HEADER 1WALL,3P,1R,3.96mm,STRAIGHT,SN SNA
CN602 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK SNA
CN603 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK SNA
CN608 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK SNA
CN609 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK SNA
D201 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D202 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D250 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D251 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D254 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D282 0402-001039 DIODE-RECTIFIER SB020,20V,600mA,MPG06,TP
D301 0402-000272 DIODE-RECTIFIER UF4001,50V,1A,DO-41,TP
D302 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D303 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D401 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP
D405 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TP
D406 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TP

AQ17HS/AQ17IS/AQ17NS

7-5

AQ19MS/AQ19IS/AQ19NS/AQ19FS

!

!

7 Electrical Parts List

Loc. No. Code No. Description Specification Remarks

D407 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP
D408 0402-000272 DIODE-RECTIFIER UF4001,50V,1A,DO-41,TP
D450 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D451 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D452 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D453 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D454 0401-000004 DIODE-SWITCHING 1SS244,250V,625mA,DO-34,TP
D456 0402-000454 DIODE-RECTIFIER RG10V1,400V,1.2A,DO-201
D478 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D501 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D503 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D504 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D508 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TP
D509 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP
D510 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP
D520 0401-000004 DIODE-SWITCHING 1SS244,250V,625mA,DO-34,TP
D521 0402-001114 DIODE-RECTIFIER 1N4936GP,400V,1A,DO-204AL,TP
D522 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D523 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D530 0402-000017 DIODE-RECTIFIER RGP02-12,1200V,0.5A,DO-204AL,T
D532 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D540 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D551 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D552 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D553 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D561 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D598 0402-000017 DIODE-RECTIFIER RGP02-12,1200V,0.5A,DO-204AL,T
D599 0402-000017 DIODE-RECTIFIER RGP02-12,1200V,0.5A,DO-204AL,T
D602 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D604 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TP
D605 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TP
D606 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,TP
D620 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D621 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
D640 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP
D642 0402-001118 DIODE-RECTIFIER UF1G,400V,1.2A,DO-204AL,TP
D644 0402-001190 DIODE-RECTIFIER RG10Z,200V,1.2A,DO-15,TP
D646 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TP
D650 0402-000017 DIODE-RECTIFIER RGP02-12,1200V,0.5A,DO-204AL,T
D670 0403-000509 DIODE-ZENER MTZJ5.6B,5.6V,5.45-5.73V,500mW
D702 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,TP
D703 0402-001111 DIODE-RECTIFIER 1N5397GP,600V,1.5A,DO-204AC,TP
D704 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP
EY301 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNA
EY302 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNA
EY401 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNA
EY402 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNA
EY403 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNA
EY404 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNA
EY405 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY408 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY409 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY410 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA

7-6 AQ17HS/AQ17IS/AQ17NS

AQ19MS/AQ19IS/AQ19NS/AQ19FS

!

!

7 Electrical Parts List

Loc. No. Code No. Description Specification Remarks

EY411 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY412 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNA
EY413 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNA
EY415 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY420 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY440 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY441 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY501 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNA
EY502 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNA
EY503 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY504 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY505 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY506 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY507 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY508 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY509 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY510 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY511 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY512 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY550 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY599 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNA
EY6 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNA
EY601 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY602 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY603 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNA
EY604 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNA
EY607 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNA
EY608 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNA
EY609 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNA
EY61 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNA
EY610 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNA
EY611 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNA
EY612 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNA
EY613 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY614 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY615 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY616 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY703 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY704 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
EY705 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA
FH601 3602-000001 FUSE-CLIP -,-,30mohm SNA
IC202 1203-000515 IC-VOL. DETECTOR 7042,TO-92,3P,177MIL,PLASTIC,4 SNA
IC280 1103-001150 IC-EEPROM
IC402 1203-001099 IC-PWM CONTROLLER 3843,DIP,8P,250MIL,PLASTIC,30V
IC501 1203-000610 IC-PWM CONTROLLER
IC621 1203-000002 IC-POSI.ADJUST REG. 431,TO-92,3P,-,PLASTIC,2.44/2.
IC701 1203-002081 IC-PWM CONTROLLER
JP104 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP106 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP113 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP114 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP116 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP150 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.

524C80D81,8KBit,DIP,8P,300MIL,10mS,5V,10%,PLASTIC,-25to+70C,10uA,CMOS,ST

494,DIP,16P,300MIL,PLASTIC,40V,1W,0TO+70C,250MA,4.75/5.25V,ST

33260,DIP,8P,300MIL,PLASTIC,-,600mW,-40to+105C,-,-,ST

AQ17HS/AQ17IS/AQ17NS

7-7

AQ19MS/AQ19IS/AQ19NS/AQ19FS

7 Electrical Parts List

Loc. No. Code No. Description Specification Remarks

JP151 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP153 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP154 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP157 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP158 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP159 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP167 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP178 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP184 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP186 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP187 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP189 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP190 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP191 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP192 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP193 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP194 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP197 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP198 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP204 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP210 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP212 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP213 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP216 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP227 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP239 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP245 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP266 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP267 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP268 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP269 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP275 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP276 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP289 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP294 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP295 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP297 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP302 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP303 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP307 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP308 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP323 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP324 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP327 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP328 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP334 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP335 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP337 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP340 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP344 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP346 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP361 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.

7-8 AQ17HS/AQ17IS/AQ17NS

AQ19MS/AQ19IS/AQ19NS/AQ19FS

7 Electrical Parts List

Loc. No. Code No. Description Specification Remarks

JP362 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP363 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP364 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP365 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP371 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP372 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP374 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP375 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP376 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP377 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP378 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP379 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP381 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP383 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP390 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP397 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP399 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP402 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP404 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP412 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP415 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP416 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP417 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP418 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP419 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP421 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP425 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP439 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP440 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP441 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP442 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP451 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP453 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP454 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP455 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP460 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP475 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP480 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP481 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP483 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP486 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP487 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP491 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP511 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP516 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP522 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP546 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP547 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP548 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP549 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP569 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP572 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP574 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.

AQ17HS/AQ17IS/AQ17NS
AQ19MS/AQ19IS/AQ19NS/AQ19FS

7-9

7 Electrical Parts List

Loc. No. Code No. Description Specification Remarks

JP578 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP579 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP581 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP585 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP586 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP587 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP588 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP589 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP590 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP591 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP596 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP597 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP598 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP603 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP609 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP615 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP616 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP617 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP619 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP623 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP626 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP629 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP630 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP632 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP633 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP635 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP637 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP638 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP640 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP643 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP644 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP645 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP646 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP647 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP648 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP649 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP650 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP651 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP652 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP653 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP654 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP655 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP656 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP657 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP659 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP660 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP661 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP662 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP663 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP664 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP665 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP666 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP675 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.

7-10 AQ17HS/AQ17IS/AQ17NS

AQ19MS/AQ19IS/AQ19NS/AQ19FS

7 Electrical Parts List

Loc. No. Code No. Description Specification Remarks

JP678 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP679 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP680 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP681 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP682 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP683 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP684 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP685 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP686 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP687 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP688 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP690 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP692 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP694 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP695 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP696 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP697 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP698 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP699 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP700 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP701 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP702 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
JP703 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
L501 2701-000179 INDUCTOR-AXIAL 33uH,10%,4.2x9.8mm
L502 2701-000187 INDUCTOR-AXIAL 4.7uH,10%,4.2x9.8mm
MP1.0 BH41-00175A PCB MAIN
Q250 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240
Q251 0501-000303 TR-SMALL SIGNAL KSA733,PNP,250mW,TO-92,TP,120-240
Q301 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240
Q408 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240
Q409 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240
Q410 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240
Q411 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240
Q412 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240
Q450 0501-000303 TR-SMALL SIGNAL KSA733,PNP,250mW,TO-92,TP,120-240
Q451 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240
Q452 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240
Q453 0501-000303 TR-SMALL SIGNAL KSA733,PNP,250mW,TO-92,TP,120-240
Q502 0501-000122 TR-SMALL SIGNAL 2N3904,NPN,625mW,TO-92,TP,100-300
Q503 0501-000581 TR-SMALL SIGNAL 2N3906,PNP,625mW,TO-92,TP,100-300
Q520 0501-000143 TR-SMALL SIGNAL 2N6520,PNP,625mW,TO-92,TP,30-200
Q521 0501-000122 TR-SMALL SIGNAL 2N3904,NPN,625mW,TO-92,TP,100-300
Q540 0501-000413 TR-SMALL SIGNAL KSP44,NPN,625mW,TO-92,TP,50-200
Q541 0501-000413 TR-SMALL SIGNAL KSP44,NPN,625mW,TO-92,TP,50-200
Q553 0501-000361 TR-SMALL SIGNAL KSC2316-Y,NPN,900mW,TO-92L,TP,120-240
Q601 0501-000010 TR-SMALL SIGNAL KSC1008,NPN,800mW,TO-92,TP,120-240
Q620 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240
Q670 0501-002228 TR-SMALL SIGNAL KTA1281,PNP,1000mW,TO-92L,TP,120-240
Q671 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240
Q672 0501-002228 TR-SMALL SIGNAL KTA1281,PNP,1000mW,TO-92L,TP,120-240
R200 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R203 2001-000515 R-CARBON 220OHM,5%,1/8W,AA,TP,1.8X3.2MM
R204 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM

AQ17IS, FR1,247*330*1.6T,1.0,1.6T,247*330*1.6T,AQUILA,-,-,-

AQ17HS/AQ17IS/AQ17NS
AQ19MS/AQ19IS/AQ19NS/AQ19FS

7-11

!

7 Electrical Parts List

Loc. No. Code No. Description Specification Remarks

R205 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R206 2001-000739 R-CARBON 4.7MOHM,5%,1/8W,AA,TP,1.8X3.2MM
R207 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM
R208 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM
R209 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R210 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R211 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R215 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R216 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R218 2001-000613 R-CARBON 3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R219 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R220 2001-000331 R-CARBON 12KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R221 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R222 2001-000613 R-CARBON 3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R225 2001-000435 R-CARBON 1MOHM,5%,1/8W,AA,TP,1.8X3.2MM
R226 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R227 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R228 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R229 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R230 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R231 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R233 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R236 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R237 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM
R238 2001-000472 R-CARBON 2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R239 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM
R240 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R242 2001-000008 R-CARBON 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R243 2001-000008 R-CARBON 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R250 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R251 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R252 2001-000563 R-CARBON 27KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R253 2004-001118 R-METAL 5Kohm,1%,1/4W,AA,TP,2.4x6.4mm
R254 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R255 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R256 2004-004367 R-METAL 90Kohm,1%,1/4W,AA,TP,6.2x2.6mm
R261 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R264 2001-000319 R-CARBON 120KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R265 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R266 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM
R267 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MM
R268 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R269 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R270 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R271 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R272 2001-000241 R-CARBON 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R278 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R280 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R281 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R282 2001-001050 R-CARBON(S) 1.5KOHM,5%,1/2W,AA,TP,2.4X6.4MM
R283 2001-000005 R-CARBON 390ohm,5%,1/8W,AA,TP,1.8x3.2mm
R284 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R301 2004-000344 R-METAL 15Kohm,1%,1/4W,AA,TP,2.4x6.4mm

7-12 AQ17HS/AQ17IS/AQ17NS

AQ19MS/AQ19IS/AQ19NS/AQ19FS

7 Electrical Parts List

Loc. No. Code No. Description Specification Remarks

R302 2004-000001 R-METAL 6.2Kohm,1%,1/4W,AA,TP,2.4x6.4m
R303 2005-001064 R-WIRE WOUND 0.9OHM,5%,2W,AA,TP,3.8X11MM
R304 2001-000037 R-CARBON(S) 330OHM,5%,1/2W,AA,TP,2.4X6.4MM
R305 2001-000105 R-CARBON 1.5KOHM,5%,1/4W,AA,TP,2.4X6.4MM
R306 2001-000016 R-CARBON(S) 1OHM,5%,1/2W,AA,TP,2.4X6.4MM
R307 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R308 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R309 2001-000977 R-CARBON 8.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R310 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R311 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R312 2008-000114 R-FUSIBLE 1.2ohm,5%,1/2W,AA,TP,3.5x9.4mm
R313 2004-001254 R-METAL 8.2Kohm,1%,1/4W,AA,TP,2.4x6.4m
R314 2004-000679 R-METAL 2Kohm,1%,1/4W,AA,TP,2.4x6.4mm
R315 2004-000334 R-METAL 150ohm,1%,1/4W,AA,TP,2.4x6.4mm
R316 2008-000114 R-FUSIBLE 1.2ohm,5%,1/2W,AA,TP,3.5x9.4mm
R402 2001-000047 R-CARBON 2.2KOHM,5%,1/4W,AA,TP,2.4X6.4MM
R403 2003-000533 R-METAL OXIDE(S) 18ohm,5%,3W,AA,TP,6x16mm
R404 2001-000515 R-CARBON 220OHM,5%,1/8W,AA,TP,1.8X3.2MM
R405 2001-001163 R-CARBON(S) 560OHM,5%,1/2W,AA,TP,2.4X6.4MM
R406 2001-000019 R-CARBON(S) 10OHM,5%,1/2W,AA,TP,2.4X6.4MM
R408 2003-000473 R-METAL OXIDE(S) 10ohm,5%,3W,AA,TP,6x16mm
R409 2003-000423 R-METAL OXIDE(S) 1.2ohm,5%,3W,AA,TP,6x16mm
R410 2003-000502 R-METAL OXIDE(S) 150ohm,5%,2W,AA,TP,4x12mm
R412 2001-001153 R-CARBON(S) 47OHM,5%,1/2W,AA,TP,2.4X6.4MM
R413 2001-001153 R-CARBON(S) 47OHM,5%,1/2W,AA,TP,2.4X6.4MM
R414 2003-000450 R-METAL OXIDE(S) 100Kohm,5%,3W,AA,TP,6x16mm
R420 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R421 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R422 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R423 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R424 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R425 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R426 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R427 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R428 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R429 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R430 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R431 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R432 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R433 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R434 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R435 2001-000037 R-CARBON(S) 330OHM,5%,1/2W,AA,TP,2.4X6.4MM
R440 2001-000022 R-CARBON(S) 33OHM,5%,1/2W,AA,TP,2.4X6.4MM
R441 2003-000661 R-METAL OXIDE(S) 33ohm,5%,2W,AA,TP,4x12mm
R444 2001-001120 R-CARBON(S) 3.3OHM,5%,1/2W,AA,TP,2.4X6.4MM
R450 2001-000011 R-CARBON 75KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R451 2001-000017 R-CARBON 4.7OHM,5%,1/4W,AA,TP,2.4X6.4MM
R452 2001-000645 R-CARBON 330KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R453 2001-000539 R-CARBON 24KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R454 2001-000241 R-CARBON 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R455 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R456 2001-000011 R-CARBON 75KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R459 2004-000657 R-METAL 27Kohm,1%,1/4W,AA,TP,2.4x6.4mm

AQ17HS/AQ17IS/AQ17NS
AQ19MS/AQ19IS/AQ19NS/AQ19FS

7-13

!!!!!

!

7 Electrical Parts List

Loc. No. Code No. Description Specification Remarks

R460 2004-000284 R-METAL 12Kohm,1%,1/4W,AA,TP,2.4x6.4mm
R461 2001-000055 R-CARBON 4.7KOHM,5%,1/4W,AA,TP,2.4X6.4MM
R462 2004-000412 R-METAL 18Kohm,1%,1/4W,AA,TP,2.4x6.4mm
R463 2001-000042 R-CARBON 1KOHM,5%,1/4W,AA,TP,2.4X6.4MM
R464 2001-000042 R-CARBON 1KOHM,5%,1/4W,AA,TP,2.4X6.4MM
R465 2001-000028 R-CARBON(S) 100OHM,5%,1/2W,AA,TP,2.4X6.4MM
R466 2001-000050 R-CARBON 2.7KOHM,5%,1/4W,AA,TP,2.4X6.4MM
R467 2008-000140 R-FUSIBLE 2.2ohm,5%,1/2W,AA,TP,3.5x9.4mm
R468 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R490 2004-000580 R-METAL 22Kohm,1%,1/4W,AA,TP,2.4x6.4mm
R501 2001-000241 R-CARBON 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R502 2001-000331 R-CARBON 12KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R503 2001-000812 R-CARBON 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R504 2001-000689 R-CARBON 390KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R505 2001-000977 R-CARBON 8.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R506 2001-000800 R-CARBON 5.1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R507 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R508 2001-000241 R-CARBON 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R509 2001-000800 R-CARBON 5.1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R510 2001-000780 R-CARBON 470OHM,5%,1/8W,AA,TP,1.8X3.2MM
R511 2001-000018 R-CARBON 6.8OHM,5%,1/4W,AA,TP,2.4X6.4MM
R512 2005-000210 R-WIRE WOUND 0.33ohm,5%,1W,AC,BK,4.5x11mm
R515 2001-000073 R-CARBON 33KOHM,5%,1/4W,AA,TP,2.4X6.4MM
R520 2001-000115 R-CARBON 82KOHM,5%,1/4W,AA,TP,2.4X6.4MM
R521 2001-000546 R-CARBON 270KOHM,5%,1/4W,AA,TP,2.4X6.4MM
R522 2004-000327 R-METAL 150Kohm,1%,1/4W,AA,TP,2.4x6.4m
R523 2001-000096 R-CARBON(S) 1MOHM,5%,1/2W,AA,TP,2.4X6.4MM
R524 2004-001254 R-METAL 8.2Kohm,1%,1/4W,AA,TP,2.4x6.4m
R525 2004-000123 R-METAL 1.2Kohm,1%,1/4W,AA,TP,2.4x6.4m
R526 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R527 2001-000878 R-CARBON 6.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R531 2004-000964 R-METAL 470Kohm,1%,1/4W,AA,TP,2.4x6.4m
R532 2004-000643 R-METAL 270Kohm,1%,1/4W,AA,TP,2.4x6.4m
R541 2001-000114 R-CARBON(S) 180KOHM,5%,1/2W,AA,TP,2.4X6.4MM
R542 2001-000114 R-CARBON(S) 180KOHM,5%,1/2W,AA,TP,2.4X6.4MM
R543 2002-001079 R-COMPOSITION 470Kohm,5%,1/2W,AA,TP,4x10mm
R545 2001-000331 R-CARBON 12KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R546 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R547 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R550 2002-001079 R-COMPOSITION 470Kohm,5%,1/2W,AA,TP,4x10mm
R551 2001-000723 R-CARBON 4.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R552 2001-000319 R-CARBON 120KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R553 2001-000105 R-CARBON 1.5KOHM,5%,1/4W,AA,TP,2.4X6.4MM
R555 2001-001144 R-CARBON(S) 4.7KOHM,5%,1/2W,AA,TP,2.4X6.4MM
R556 2001-001153 R-CARBON(S) 47OHM,5%,1/2W,AA,TP,2.4X6.4MM
R557 2003-000459 R-METAL OXIDE(S) 100ohm,5%,3W,AA,TP,6x16mm
R558 2003-000008 R-METAL OXIDE(S) 100ohm,5%,1W,AA,TP,3.3x9mm
R560 2001-000800 R-CARBON 5.1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R561 2001-000331 R-CARBON 12KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R563 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R564 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R565 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R567 2002-001079 R-COMPOSITION 470Kohm,5%,1/2W,AA,TP,4x10mm

7-14 AQ17HS/AQ17IS/AQ17NS

AQ19MS/AQ19IS/AQ19NS/AQ19FS

!!!!!

!

7 Electrical Parts List

Loc. No. Code No. Description Specification Remarks

R596 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.
R597 2002-001073 R-COMPOSITION 15Mohm,5%,1/2W,AA,TP,4.0x10mm
R598 2001-000114 R-CARBON(S) 180KOHM,5%,1/2W,AA,TP,2.4X6.4MM
R599 2001-001106 R-CARBON(S) 220KOHM,5%,1/2W,AA,TP,2.4X6.4MM
R601 2001-000354 R-CARBON 150KOHM,5%,1/4W,AA,TP,2.4X6.4MM
R602 2001-000354 R-CARBON 150KOHM,5%,1/4W,AA,TP,2.4X6.4MM
R603 2001-000022 R-CARBON(S) 33OHM,5%,1/2W,AA,TP,2.4X6.4MM
R604 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R605 2001-000044 R-CARBON 1.2KOHM,5%,1/4W,AA,TP,2.4X6.4MM
R606 2001-000085 R-CARBON(S) 100KOHM,5%,1/2W,AA,TP,2.4X6.4MM
R607 2001-000087 R-CARBON(S) 120KOHM,5%,1/2W,AA,TP,2.4X6.4MM
R609 2001-000376 R-CARBON 15OHM,5%,1/8W,AA,TP,1.8X3.2MM
R620 2001-000552 R-CARBON 270OHM,5%,1/4W,AA,TP,2.4X6.4MM
R621 2001-000003 R-CARBON 330ohm,5%,1/8W,AA,TP,1.8x3.2mm
R622 2001-000241 R-CARBON 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R623 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R624 2001-000034 R-CARBON 220OHM,5%,1/4W,AA,TP,2.4X6.4MM
R625 2001-000508 R-CARBON 220KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R626 2004-000679 R-METAL 2Kohm,1%,1/4W,AA,TP,2.4x6.4mm
R627 2004-000523 R-METAL 200ohm,1%,1/4W,AA,TP,2.4x6.4mm
R628 2002-001082 R-COMPOSITION 180KOHM,2%,1W,AA,TP,4X12MM
R629 2001-000890 R-CARBON 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R630 2001-000577 R-CARBON 2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R631 2001-000577 R-CARBON 2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R640 2001-000376 R-CARBON 15OHM,5%,1/8W,AA,TP,1.8X3.2MM
R644 2001-001131 R-CARBON(S) 33KOHM,5%,1/2W,AA,TP,2.4X6.4MM
R649 2002-001079 R-COMPOSITION 470Kohm,5%,1/2W,AA,TP,4x10mm
R651 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R655 2002-001079 R-COMPOSITION 470Kohm,5%,1/2W,AA,TP,4x10mm
R656 2001-000028 R-CARBON(S) 100OHM,5%,1/2W,AA,TP,2.4X6.4MM
R668 2001-000958 R-CARBON 750OHM,5%,1/8W,AA,TP,1.8X3.2MM
R670 2002-001068 R-COMPOSITION 180Kohm,5%,1/2W,AA,TP,3.9x9mm
R671 2002-001068 R-COMPOSITION 180Kohm,5%,1/2W,AA,TP,3.9x9mm
R672 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R673 2001-000472 R-CARBON 2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R674 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R675 2001-001038 R-CARBON(S) 0.56OHM,5%,1/2W,AA,TP,2.4X6.4MM
R676 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R677 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R688 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R701 2005-001170 R-WIRE WOUND,NON 0.33ohm,1%,3W,AA,TP,5.5x15mm
R702 2001-001013 R-CARBON 9.1KOHM,5%,1/4W,AA,TP,2.4X6.4MM
R703 2001-000302 R-CARBON 10OHM,5%,1/8W,AA,TP,1.8X3.2MM
R704 2004-001863 R-METAL 680Kohm,1%,1/4W,AA,TP,2.4x7mm
R705 2004-001863 R-METAL 680Kohm,1%,1/4W,AA,TP,2.4x7mm
R706 2004-001863 R-METAL 680Kohm,1%,1/4W,AA,TP,2.4x7mm
R711 2008-000125 R-FUSIBLE 10ohm,5%,1/4W,AA,TP,2.6x6.7mm
R712 2001-000302 R-CARBON 10OHM,5%,1/8W,AA,TP,1.8X3.2MM
R721 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM
SK530 4715-001055 SURGE ABSORBER 1kV,+50-10%,-,-,RADIAL SNA
TCO BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK SNA
X201 2801-003413 CRYSTAL-UNIT 24MHz,30ppm,28-ABQ,20pF,20ohm,
ZD201 0403-000367 DIODE-ZENER UZ7.5BSC,7.5V,7.33-7.64V,500mW

AQ17HS/AQ17IS/AQ17NS

7-15

AQ19MS/AQ19IS/AQ19NS/AQ19FS

7 Electrical Parts List

Loc. No. Code No. Description Specification Remarks

ZD286 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500mW
ZD450 0403-000004 DIODE-ZENER UZ12BM,12V,11.6-12.4V,500mW,DO
ZD520 0403-001068 DIODE-ZENER UZ4.7BSA,4.7V,4.47-4.65V,500mW
ZD601 0403-000753 DIODE-ZENER MTZJ27D,27V,26.29-27.64V,500mW
ZD705 0403-000004 DIODE-ZENER UZ12BM,12V,11.6-12.4V,500mW,DO
ZD706 0403-000538 DIODE-ZENER MTZ16C,16V,15.69-16.51V,500mW,

HS651 BH99-00011B ASSY HEAT/SINK HS,SPRING,78R12,7805,-,OIL SILICON SNA
CIS 0205-001027 OIL-SILICON G746,-,- SNA
CIS 1203-000001 IC-POSI.FIXED REG. 7805,TO-220,3P,-,PLASTIC,4.8/5
CIS 1203-000165 IC-POSI.ADJUST REG.
CIS BH61-00004A SPRING-TR CDA,CDB,SUS304,T0.5,-,-,-,- SNA
CIS BH62-00045A HEAT SINK-TR AQ19FS,A1050S,T1.0,25,54,-,-,- SNA

HS504 BH99-00013D ASSY HEAT/SINK HS,SPRING,2SK2761,-,-,OIL SILICON
CIS 0205-001027 OIL-SILICON G746,-,- SNA
CIS 0505-001266 FET-SILICON 2SK2761-01MR,N,600V,10A,0.85oh
CIS BH61-00004A SPRING-TR CDA,CDB,SUS304,T0.5,-,-,-,- SNA
CIS BH62-00042A HEAT SINK-POWER AQ19FS,A1050S,T1.0,80,55,-,-,- SNA

78R12,TO-220,4P,-,PLASTIC,11.7/12.3V,1.5W,-20TO+80C,1A,-,ST

HS402_1 BH99-00029C ASSY HEAT/SINK HS,SPRING,FJL6820,10F150S,-,MICA,OIL SILICON SNA
CIS 0205-001027 OIL-SILICON G746,-,- SNA
CIS 0402-001319 DIODE-RECTIFIER SDS10F150S,1.5KV,10A,TO-220F,ST
CIS 0502-001202 TR-POWER FJL6820,NPN,200000MW,TO-264,ST,8­CIS BH61-70003A SPRING CVT4857,STS304-W1/2H,T0.5,W3.8 SNA
CIS BH62-00001A INSULATION-MICA CSM920B,MICA,-,-,-,-,-,-,POWER-TR SNA
CIS BH62-00040A HEAT SINK-HOR. PN19MT,A1050S,T2.0,95,110,-,-,- SNA

HS409 BH99-00030B ASSY HEAT/SINK HS TR,SCREW+NUT,SKS10N20(4),-,-,OIL SILICON SNA
CIS 0205-001027 OIL-SILICON G746,-,- SNA
CIS 0505-001305 FET-SILICON SKS10N20,N,200V,6.9A,0.36OHM,39W,TO-220F
CIS 6006-001008 SCREW-ASS’Y MACH WSP,BH,+,M3,L10,ZPC(YEL),SWRCH SNA
CIS 6021-000118 NUT-HEXAGON 1C,M3,ZPC(YEL),SM20C SNA
CIS BH62-00044A HEAT SINK-TR AQ19FS,A1050S,T2.0,20,55,-,-,- SNA

HS401 BH99-00041A ASSY HEAT/SINK HS,SPRING,SFP9634,-,-,OIL SILICON SNA
CIS 0205-001027 OIL-SILICON G746,-,- SNA
CIS 0505-001359 FET-SILICON SFP9634,P,-250V,-5A,1.3OHM,70W,TO-220
CIS BH61-00004A SPRING-TR CDA,CDB,SUS304,T0.5,-,-,-,- SNA
CIS BH62-00039A HEAT SINK-TR PN19MT,A1050S,T1.0,20,20,-,-,- SNA

HS301 BH99-00043A ASSY HEAT/SINK HS V.IC,SCREW+NUT,KA2142,-,-,OIL SILICON SNA
CIS 0205-001027 OIL-SILICON G746,-,- SNA
CIS 1204-001508 IC-VERTICAL DEF.
CIS 6006-001008 SCREW-ASS’Y MACH WSP,BH,+,M3,L10,ZPC(YEL),SWRCH SNA
CIS 6021-000118 NUT-HEXAGON 1C,M3,ZPC(YEL),SM20C SNA
CIS BH62-00049A HEAT SINK-V/IC AQ17,A1050S,T1.0,H60,L77,-,-,- SNA

KA2142,SIP,10P,-,PLASTIC,35V,15W,-20TO+70C,ST,VERTICAL DEFLECTION

HS508 BH99-00045A ASSY HEAT/SINK HS,SCREW+NUT,TIP29C,-,-,OIL SILICON SNA
CIS 0205-001027 OIL-SILICON G746,-,- SNA
CIS 0502-000348 TR-POWER TIP29C,NPN,2W,TO-220,-,15-75
CIS 6006-001008 SCREW-ASS’Y MACH WSP,BH,+,M3,L10,ZPC(YEL),SWRCH SNA
CIS 6021-000118 NUT-HEXAGON 1C,M3,ZPC(YEL),SM20C SNA

7-16 AQ17HS/AQ17IS/AQ17NS

AQ19MS/AQ19IS/AQ19NS/AQ19FS