SAMSUNG 650MP User Manual
SyncMaster 650MP, 650FP
LCD Display
User Manual
Safety Instructions
Notational
Note
These safety instructions
age.
Make sure to read the instructions carefully and use the product in the correct manner.
Warning / Caution
Failure to follow directions noted by this symbol could result in bodily
harm or damage to the equipment.
Note
Prohibited
Do not disassemble
Do not touch
must be followed to ensure your safety and prevent property dam-
Important to read and understand at all times
Disconnect the plug from the
outlet
Ground to prevent an electric
shock
Power
When not used for extended period of time, set your computer to DPM.
If using a screen saver, set it to active screen mode.
The images here
(or countries).
Shortcut to Anti-Afterimage Instructions
Do not use a damaged power cord or plug or a damaged or
loose power outlet.
• Otherwise, this may result in electric shock or fire.
Do not touch the power plug with wet hands when removing or
plugging the plug into the outlet.
• Otherwise, this may result in electric shock.
Make sure to connect the power cord to a grounded power out-
let.
are for reference only, and are not applicable in all cases
Otherwise, it may result in electric shock or personal injury.
•
1
Safety Instructions
Ensure that the power plug is plugged into the power outlet
firmly and correctly.
•
Otherwise, this may result in fire.
Do not forcefully bend or pull the power plug and do not place
any heavy material on it.
• Otherwise, this may result in fire.
Do not connect multiple appliances to the same power outlet.
• Otherwise, this may cause fire due to overheating.
Do not disconnect the power cord while using the product.
Installation
• Otherwise, this may
electric shock.
To disconnect the apparatus from the mains, the plug must be
pulled
be readily operable.
• Otherwise, this may cause electric shock or fire.
Use only the power cord provided by our company. Do not use
the provided power cord of another product.
• Otherwise, this may result in fire or electric shock.
Be sure to contact an authorized Service Center when installing your
monitor in a
midity, and exposed to chemical substances and where it operates for 24
hours such as at airports, train stations etc.
Failure to do so may cause serious damage to your monitor.
from
out
location with heavy dust, high or low temperatures, high hu-
the mains socket, therefore the mains plug shall
result in damage to the product due to
Ensure that at least two persons lift and move the product.
• Otherwise, it may
or damage the product.
When installing the product in a cabinet or rack, make sure that
the front end of the bottom of the product does not project out.
• Otherwise, it may fall or cause personal injury.
• Use a cabinet or rack of a size appropriate to the product.
DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIGARETTES AND ANY HEATING APPLIANCES NEAR THE PRODUCT.
• Otherwise, this may result in fire.
be dropped and cause personal injury, and/
2
Safety Instructions
Keep heating appliances as far away from the power cord or the
product as possible.
•
Otherwise, this may result in electric shock or fire.
Do not install it in a badly ventilated location such as a bookcase
or closet.
• Otherwise, this may
ternal temperature.
When putting the product down, make sure to put it down softly.
• Otherwise, this may result in damage to the screen display.
Do not place the front of the product on the floor.
• Otherwise, this may result in damage to the screen display.
Ensure that an authorized installation company installs the wall
mount.
• Otherwise, it may fall and cause personal injury.
• Make sure to install the specified wall mount.
Install your product in a well ventilated location. Ensure that
there is a clearance of more than 4 inches (10 cm) from the wall.
• Otherwise, it may
temperature.
Ensure that the packaging vinyl is kept away from children.
result in fire due to an increase in the in-
result in fire due to an increase in the internal
Clean
• Otherwise, it may
play with it.
If the height of your monitor is adjustable, do not place any object or part of your body on the stand when lowering it.
• This
it.
When cleaning the monitor case or the surface of the TFT-LCD screen,
wipe with a slightly moistened, soft cloth.
Do not spray cleaner directly onto the surface of the product.
• Otherwise, this may
the structure and the screen surface may peel off.
When cleaning the power plug pins or dusting the power outlet,
clean it with a dry cloth.
Otherwise, it may result in fire.
•
may
cause
result in serious harm (suffocation) if children
damage to the product or the person carrying
result in the discoloration and distortion of
3
Safety Instructions
When cleaning the product, make sure to disconnect the power
cord.
•
Otherwise, it may result in electric shock or fire.
When cleaning the product, disconnect the power cord and
clean it with a soft, dry cloth.
Others
• (Do not
mosquito repellant, lubricant, or cleaner.) These may change
the appearance of the product surface and peel off the indication labels on the product.
Since the product housing is easily scratched, make sure to use
the specified cloth only.
When cleaning the product, do not spray water directly onto the
main body of the product.
• Ensure that water does not enter the product and that it is not
wet.
• Otherwise, this may result in electric shock, fire or a malfunc-
tion.
The product is a high voltage product. Do not disassemble, repair or modify the product yourself.
• Otherwise, this may result in electric shock or fire. If the product
needs to be repaired, contact a Service Center.
If there is a strange smell or a strange sound or smoke is coming
from the product, disconnect the power plug immediately and contact a Service Center.
use chemicals such as wax, benzene, alcohol, thinner,
• Otherwise, this may result in electric shock or fire.
Do not place this product in a location exposed to moisture, dust,
smoke, water, or in a car.
• Otherwise, this may result in electric shock or fire.
When you drop the product or the case is broken, turn the power
off and disconnect the power cord. Contact a Service Center.
• Otherwise, this may result in electric shock or fire.
If thunder or lightning is occurring, do not touch the power cord
or antenna cable.
•
Otherwise, this may result in electric shock or fire.
4
Safety Instructions
Do not try to move the monitor by pulling only the wire or the
signal cable.
• Otherwise,
the product or fire due to damage to the cable.
Do not lift or move the product back and forwards or right and
left while only holding the power cord or signal cables.
• Otherwise,
the product or fire due to damage to the cable.
Make sure that the ventilating opening is not blocked by a table
or curtain.
• Otherwise,
temperature.
Do not place any containers containing water, vases, flowerpots, medicines as well as any metal on the product.
• If
water
power cord and contact a Service Center.
• This may result in a product malfunction, electric shock, or fire.
Do not use or keep combustible spray or flammable material
near the product.
•
Otherwise, this may result in an explosion or fire.
may
it
it
it
or
a foreign material enters the product, disconnect the
fall and result in electric shock, damage to
may
fall and result in electric shock, damage to
may
result in fire due to an increase in the internal
Do not insert any metal, such as chopsticks, coins, pins and
steel, or flammable
product (through the ventilating openings, input and output terminals, etc).
• If water or foreign material enters the product, disconnect the
power cord and contact a Service Center.
• Otherwise, this may result in electric shock or fire.
When using a fixed screen for a long time, an afterimage or stain
may occur.
• If you are
it into sleep mode or use a moving screen saver.
Set a resolution and frequency appropriate to the product.
• Otherwise, your eyesight may be damaged.
When using headphones or earphones, do not turn the volume
too high.
• Having the sound too loud may damage your hearing.
To avoid eyestrain, do not sit too close to the product.
objects, such as matches or paper, inside the
not using your product for a long period of time, put
5
Safety Instructions
Take a rest for at least five (5) minutes after using the monitor
for one (1) hour.
This reduces eye fatigue.
Do not install it in an unstable location such as an unstable rack
or uneven surface or a location exposed to vibrations.
• Otherwise, it may
the product.
• If you use the product in a location exposed to vibrations, it may
damage the product and result in fire.
When moving the product, turn the power off and disconnect
the power plug,
product.
• Otherwise, it may result in electric shock or fire.
Ensure that children do not hang onto the product or climb up
onto the product.
• The product may fall and cause personal injury or death.
If you do not use the product for a long period of time, disconnect
the power cord from the power outlet.
• Otherwise, this may result in overheating or fire due to dust,
and may result in fire due to electric shock or leakage.
Do not place any heavy items or toys or confectionery, such as
cookies etc. that may attract the attention of children and to the
product.
fall and cause personal injury and/or damage
antenna cable, and all the cables connected to the
• Your children may hang onto the product causing it to fall and
this may result in personal injury or death.
Be careful that children do not place the battery in their mouths
when removed from the remote control. Place the battery in a location that children or infants cannot reach.
• If children have had the battery in their mouths, consult your
doctor immediately.
When replacing the battery, insert it with the right polarity (+, -).
• Otherwise, the battery may become damaged or it may cause
fire, personal injury or damage due to leakage of the internal
liquid.
Use only the specified standardized batteries, and do not use a
new battery and a used battery at the same time.
• Otherwise, the batteries
sonal injury or damage due to a leakage of the internal liquid.
The batteries (and rechargeable batteries) are not ordinary refuse and must
is responsible for returning the used or rechargeable batteries for
recycling.
be returned for recycling purposes. The customer
may be damaged or cause fire, per-
6
Safety Instructions
• The
or near any heat such as a fire or heater.
• This
to the product.
•
• Otherwise, this may result in electric shock or fire.
plug; ventilate immediately.
• If a spark occurs, it may cause an explosion or fire.
panel becomes hot. Do not touch it.
customer can return used or rechargeable batteries to a
public
nearby
type of the battery or rechargeable battery.
Do not place the product in a location exposed to direct sunlight
may
fire.
Do not drop any objects onto the product or cause any impact
Otherwise, this may result in electric shock or fire.
Do not use a humidifier near the product.
When there is a gas leak, do not touch the product or the power
If the product has been turned on for a long time, the display
recycling center or to a store selling the same
reduce
the lifetime of the product, and may result in
Keep the small accessories in a location out of the reach of children.
Be careful when adjusting the angle of the product or the height
of the stand.
• This may result
become caught.
• Also, if you tilt the product too far, it may fall and cause personal
injury.
Do not install the product in a location low enough for children
to reach.
• Otherwise, it may fall and result in personal injury.
• Since
Do not put any heavy objects on the product.
• This may result
the front part of the product is heavy, install the product
on a level and stable surface.
uct.
in personal injury as your hand or fingers may
in personal injury and/or damage to the prod-
7
Introduction
Package Contents
Note
Please make sure the following items are included with your LCD Display.
If any items are missing, contact your dealer.
Contact a local dealer
to buy optional items.
Checking the Contents of the Package
Remove the lock from the package box, as shown in the figure above.
• After unpacking the package, make sure to check the contents of the package.
• Make sure to keep the package box for transporting the product in the future.
Unpacking
Lift up the package box by
holding the grooves on
both sides of the package
box.
Note
Check the contents of the
package.
LCD Display
Remove the Styrofoam
and vinyl cover.
8
Manuals
Introduction
Quick Setup Guide Warranty Card
(Not available in all loca-
tions)
Cables
Power Cord D-Sub Cable
Others
Remote Control
Batteries (AAA X 2)
User's Guide
BNC to RCA Adaptor Jack
(BP59-00138A)
Ferrite Core for Power Cord
Sold separately
DVI Cable NetworkBox Wall Mount KIT
(Not available in all loca-
tions)
9
Introduction
Sold separately
RGB to BNC Cable BNC to BNC Cable Semi Stand KIT
Ferrite Core
• The ferrite cores are used to shield the cables from interfer-
ence.
Your LCD Display
Front
• When
around the cable near the plug.
connecting a cable, open the ferrite core and clip it
MENU button [MENU]
Opens the on-screen menu and exits from the menu. Also use to exit the
OSD menu or return to the previous menu.
Navigate buttons (Up-Down buttons)
Moves from one menu item to another vertically or adjusts selected menu
values.
Adjust buttons (Left-Right buttons) / Volume buttons
Moves from one menu item to another horizontally or adjusts selected
menu values. When OSD is not on the screen, press the button to adjust
volume.
ENTER button [ENTER]
Activates a highlighted menu item.
SOURCE button [SOURCE]
10
Introduction
Switches from PC mode to Video mode. Selects the input source that an
external device is connected to.
[PC] → [DVI] → [AV] → [Component] → [HDMI] → [MagicInfo] → [BNC]
Note
• MagicInfo can only be enabled when a network box is connected.
• The HDMI port and network
box cannot be connected at the same time.
PIP button
Push the PIP button to turn the PIP screen On / Off.
More than one PIP cannot overlap on screen as BNC and the component
use the same terminal.
• PC : DVI / AV / Component / HDMI
• BNC : DVI / AV / HDMI
• DVI / AV : PC / BNC
• Component : PC
• HDMI : PC / BNC
Power button [ ]
Use this button for turning the LCD Display on and off.
Brightness Sensor (Optional)
Automatically detects the surrounding brightness.
Note
Rear
This function is
ness sensor.
activated only on the models equipped with an auto bright-
Power indicator
Shows PowerSaver mode by blinking green
Note
See PowerSaver described in
power saving functions. For energy conservation, turn your LCD Display
OFF when it is not needed or when leaving it unattended for long periods.
the manual for further information regarding
Remote Control Sensor
Aim the remote control towards this spot on the LCD Display.
Note
For detailed information
Setup. The LCD Display 's configuration at the back may vary slightly depending on the model.
concerning cable connections, refer to Connecting Cables under
11
Introduction
POWER S/W ON [ │ ] / OFF [O]
Switches the LCD Display On/Off.
POWER
The power cord plugs into the LCD Display
and the wall outlet.
RS232C OUT/IN (RS232C Serial PORT)
MDC(Multiple Display Control) Program Port
RGB IN (PC Connection Terminal (In-
put))
• Use a D-Sub Cable (15 pin D-Sub) - PC
mode (Analog PC)
• Connect the RGB IN port on the monitor
to the BNC port on the PC using the RGB
to BNC cable.
DVI IN (PC Video Connection Terminal)
Use a DVI Cable (DVI-D to DVI-D) - DVI
mode (Digital PC)
12
Introduction
DVI/RGB/HDMI AUDIO IN (PC/DVI/
HDMI Audio Connection Terminal (Input))
AV/COMPONENT AUDIO IN [R-AUDIO-
L]
Connect the port of the DVD, VCR (DVD /
DTV Set-Top Box) to the [R-AUDIO-L] port
of the LCD Display.
DVI OUT
• Connect a monitor to another monitor
through a DVI cable.
• Connect the DVI OUT port on the monitor
to the HDMI IN port on the other monitor
using the DVI to HDMI cable.
• DVI, HDMI and network signals sent via
the DVI OUT port are displayed on the
second display which has the DVI IN port.
Note
Up
6
Full HD or 10 HD monitors can be
to
connected (May differ depending on the
product).
AV IN [VIDEO]
Connect the [VIDEO] terminal of your monitor to the video output terminal of the external
device using a VIDEO cable.
AUDIO OUT
Headphone/External speaker output terminal.
HDMI IN
Connect the HDMI terminal at the back of
your LCD Display to the HDMI terminal of
your digital output device using a HDMI cable.
Up to HDMI cable 1.0 can be supported.
13
Introduction
BNC OUT [R, G, B, H, V] (BNC Terminal
(Output))
BNC (Analog PC) Connection: connecting
the R, G, B, H, V ports.
The number of LCD Displays that can be
connected to the loopout depends on the cables, signal source, etc. With cables or signal
source where there is no degradation, up to
10 LCD Displays can be connected (May not
be supported depending on the connected
cable).
BNC/COMPONENT IN [R/Y, G/PB, B/
PR, H, V] (BNC/Component Connection Terminal (input))
- During BNC input, please check specifications for the input ports below.
• [R/Y] --> Red port input
• [G/PB] --> Green port input
• [B/PR] --> Blue port input
- During component input, please check
specifications for the input ports below.
• [R/Y] --> Green port input
• [G/PB] --> Blue port input
• [B/PR] --> Red port input
SBB Lcok
Connect the network box.
Note
• For
details,
user manual.
please
see the network box
Note
See Connecting Cables
Remote Control
Note
The performance of the remote control may be affected by a TV or other electronic device
operating near the LCD Display , causing a malfunction due to interference with the frequency.
• Purchasing the network box is optional.
for further information regarding cable connections.
14
Introduction
POWER
OFF
Number Buttons
DEL / GUIDE button
+ VOL -
SOURCE
D.MENU
TOOLS
Up-Down Left-Right buttons
INFO
COLOR BUTTONS
TTX/MIX
MTS/DUAL
ENTER/PRE-CH
MUTE
CH/P
TV
MENU
RETURN
EXIT
MagicInfo
1.
2. OFF
3. Number Buttons Press to change the channel.
4. DEL / GUIDE button
POWER
Turns the product On.
Turns the product Off.
The "-" button is used to select Digital channels.
Electronic Program Guide (EPG) display.
- This function does not work for this LCD Display.
5. + VOL - Adjusts the audio volume.
SOURCE
6.
7.
D.MENU DTV menu display
8. TOOLS
Press the button to change the input signal SOURCE.
Changing
that are connected to the LCD Display at the time.
- This function does not work for this LCD Display.
Use to quickly select frequently used functions.
15
SOURCE
the
is only allowed for external devices
Introduction
- This function does not work for this LCD Display.
9.
Up-Down
tons
10.
11. COLOR BUTTONS Press to add or delete channels and to store channels to the
12.
13. MTS/DUAL - This function does not work for this LCD Display.
INFO
TTX/MIX
Left-Right
but-
Moves from one menu item to another horizontally, vertically
or adjusts selected menu values.
Current picture information
corner of the screen.
favorite channel list in the “Channel List” menu.
- This function does not work for this LCD Display.
TV channels provide
text.
- Teletext Buttons
- This function does not work for this LCD Display.
is displayed on the upper left
written information services via tele-
MTS-
You can select MTS (Multichannel Television Stereo) mode.
Audio Type MTS/S_Mode Default
FM Stereo Mono Mono Manual
Stereo Mono ↔ Stereo
SAP Mono ↔ SAP Mono
DUAL-
STEREO/MONO, DUAL l / DUAL ll and MONO/NICAM
MONO/NICAM STEREO can be operated depending on the
broadcasting type by using the DUAL button on the remote
control while watching TV.
14.
15.
16.
ENTER/PRE-CH
MUTE
CH/P In TV mode, selects TV channels.
This button is
channel.
- This function does not work for this LCD Display.
Pauses
played on the lower left corner of the screen. The audio
comes back on if MUTE or - VOL + is pressed in the Mute
mode.
used to return to the immediately previous
(mutes)
the
Change
audio output temporarily. This is dis-
- This function does not work for this LCD Display.
17. TV Selects the TV mode directly.
- This function does not work for this LCD Display.
18. MENU Opens the on-screen
closes the adjustment menu.
16
menu and exits from the menu or
Introduction
19. RETURN
20. EXIT
21. MagicInfo
Mechanical Layout
Mechanical Layout
Returns to the previous menu.
Exits from the menu screen.
MagicInfo Quick Launch Button.
Note
MagicInfo can only
nected.
be enabled when a network box is con-
Installation VESA Bracket
•
When installing VESA, make sure to comply with the international VESA standards.
Purchasing
•
SAMSUNG Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket.
• At least 2 persons are needed in order to move the LCD Display.
VESA Bracket and Installation Information : Please contact your nearest
17
Introduction
• SAMSUNG
Dimensions
For securing the
mm length.
not
responsible for any product damage or any injury caused by installation
is
at customer's discretion.
Notice
bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12
Wall Bracket Installation
• Contact a technician for installing the wall bracket.
• SAMSUNG Electronics is not responsible for any damages to the product or harm to
customers when the installation is done by the customer.
• This product is for installing on cement walls. The product may not stay in place when
installed on plaster or wood.
Components
Only use the components and accessories shipped with the product.
Wall Bracket(1) Hinge(Left 1, Right1)Plastic
Hanger
(4)
Screw
(A)(11)
Screw
(B)(4)
Anchor
(11)
Wall Bracket Assembly
Note
There are two hinges(left and right). Use the correct one.
1.
Insert and tighten the Captive Screw in the direction of the arrow.
When done, mount the wall bracket on the wall.
18
Introduction
There are two hinges(left and right). Use the correct one.
A - Captive Screw
B - Wall Bracket
C - Hinge (Left)
D - Hinge (Right)
2. Before
of the product is correct.
If the length is too short or long, loosen all or some of the 4screws on the wall bracket to
adjust the length.
drilling into the wall, check if the length between the two locking holes at the back
A - Length between the two locking holes
3. Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit
to drill holes
of the brackets and hinge holes to the corresponding anchor holes and insert and tighten
the 11 screws A.
deeper than 35 mm. Fix each anchor in the corresponding hole. Match each
19
Introduction
To mount the product on the wall bracket
The shape of
hanger and the screw are the same)
1. Remove the 4 screws on the back of the product.
2. Insert the screw B into the plastic hanger.
the product may vary depending on the model. (The assemblies of the plastic
Notice
• Mount
and right plastic hangers.
• Be careful when installing the product on the bracket as fingers can be caught in the
holes.
• Make sure the wall bracket is securely fixed to the wall, or the product may not stay
in place after installation.
3. Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product.
the
product
on the wall bracket and make sure it is properly fixed to the left
20
Introduction
4. Remove safety pin
holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to
re-insert and tighten the safety pin (3) to securely hold the product to the bracket.
A - LCD Display
B - Wall Bracket
C - Wall
(3) and insert the 4 product holders into the corresponding bracket
Wall Bracket Angle Adjustment
Adjust the bracket angle to -2° before installing it on the wall.
1. Fix the product to the wall bracket.
2. Hold the product
adjust the angle.
Note
You can adjust the bracket angle between -2° and 15°.
at the top in the center and pull it forward (direction of the arrow) to
21
Introduction
Make sure to use the top center, and not the left or the right side of the product to adjust the
angle.
22
Connections
Connecting a Computer
There are several ways to connect the computer to the monitor. Choose
one from the following options.
Using the D-sub (Analog) connector on the video card.
• Connect the D-sub
Display and the 15 pin D-sub Port on the computer.
Using the DVI (Digital) connector on the video card.
• Connect the DVI
Display and the DVI port on the computer.
to the 15-pin, [RGB IN] port on the back of your LCD
Cable to the [DVI IN] port on the back of your LCD
18
Connections
Using the HDMI (digital) output on the graphics card.
• Connect the [HDMI IN] port on the LCD Display to the HDMI port on
the PC using the HDMI cable.
Note
When the HDMI
the Source List and Edit Name before selecting PC or DVI device so that
normal PC screen and sound can be outputted. Note that sound is only
cable to the PC, ensure that you select HDMI from both
available when connected according to the option
Using the BNC (Analog) connector on the video card.
• Connect the [BNC/COMPONENT
port on the PC using the BNC to BNC cable.
IN] port on the monitor to the BNC
19
that follows.
Connections
Connect the audio cable for your LCD Display to the audio port on the back
of the LCD Display.
Connect the power cord for your LCD Display to the power port on the back
of the LCD Display. Turn on the power switch.
Note
• Turn on both your computer and the LCD Display.
• Contact a local SAMSUNG Electronics
Connecting to Other devices
• AV input devices such as DVD players, VCRs or camcorders as well as your computer
can be connected to the LCD Display. For detailed information on connecting AV input
devices, refer to the contents under Adjusting Your LCD Display.
• The LCD Display 's configuration at the back may vary slightly depending on the LCD
Display model.
Connecting AV Devices
Service Center to buy optional items.
1. Connect an audio
L]] port on the monitor, and connect the video output port on the external device to the
[AV IN [VIDEO]] port on the monitor.
2. Play the DVD, VCR or Camcorder with a DVD disc or tape inserted.
3. Select AV using the SOURCE button on the front of the LCD display or on the remote.
cable to the audio output port on the external device and [[R-AUDIO-
20
Connecting to a Camcorder
Connections
1. Locate the AV
of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on
the camcorder and the [AV/COMPONENT AUDIO IN [R-AUDIO-L]] on the LCD Display .
2. Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the [AV
IN [VIDEO]] on the LCD Display .
3. Select AV for the Camcorder connection using the SOURCE button on the front of the
LCD Display or on the remote control.
4. Then, start the Camcorder with a tape inserted.
Note
The audio-video cables shown here are usually included with a Camcorder. (If not, check
your local electronics store.) If your camcorder is stereo, you need to connect a set of two
cables.
output jacks on the camcorder. They are usually found on the side or back
Connecting the BNC to BNC cable
1. Connect the [BNC/COMPONENT
port on the external device using the BNC to BNC cable.
IN [R/Y, G/PB, B/PR]] ports on the monitor to the BNC
21
Connections
2. Select BNC
LCD Display or on the remote control.
for
the
Camcorder connection using the SOURCE button on the front of the
Connecting Using a DVI Cable
1. Connect between the [DVI OUT] port on the LCD Display and the input port on another
monitor using a DVI cable.
2. Connect between the
another monitor using a stereo cable.
3. Select DVI using the SOURCE button on the front of the LCD Display or on the remote
control.
Note
DVI OUT does not support HDCP.
[AUDIO OUT] port on the LCD Display and the audio input port on
Connecting Using a HDMI Cable
1. Connect input devices
LCD Display using an HDMI cable.
2. Select HDMI using the SOURCE button on the front of the LCD Display or on the remote
control.
such as a Blu-Ray/DVD player to the [HDMI IN] terminal of the
22
Connections
Note
In HDMI mode, only PCM format audio is supported.
Connecting Using a DVI to HDMI Cable
1. Connect
the LCD Display using a DVI to HDMI cable.
2. Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored
audio output terminals of the digital output device, and connect the opposite jack to the
[DVI / RGB /HDMI AUDIO IN] terminal of the LCD Display.
3. Select HDMI using the SOURCE button on the front of the LCD Display or on the remote
control.
the
DVI
Connecting a DVD Player
output terminal of a digital output device to the [HDMI IN] terminal of
1. Connect a set
on the LCD Display and the AUDIO OUT jacks on the DVD player.
of audio cables between the [AV/COMPONENT AUDIO IN [R-AUDIO-L]]
23
Connections
2. Connect a Component
port on the LCD Display and the PR, Y, PB jacks on the DVD player.
Note
• Select Component for the connection to a DVD player using the SOURCE button on the
front of the LCD Display or on the remote control.
•
Then, start the DVD Player with a DVD disc inserted.
• A component cable is optional.
• For an explanation of Component video, consult your DVD manual.
cable between the [BNC/COMPONENT IN [R/Y, G/PB, B/PR]]
Connecting a DTV Set Top (Cable/Satellite) Box
1. Connect a Component
port on the LCD Display and the PR, Y, PB jacks on the Set Top Box.
2. Connect a set of audio cables between the [AV COMPONENT AUDIO IN [R-AUDIO-L]]
on the LCD Display and the AUDIO OUT jacks on the Set Top Box.
Note
• Select Component for the connection to a DTV Set Top Box using the SOURCE button
on the front of the LCD Display or on the remote control.
• For an explanation of Component video, see your Set Top Box owner's manual.
cable between the [BNC/COMPONENT IN [R/Y, G/PB, B/PR]]
24
Loading...