Samsung 550EX-N-QSG User Manual
LCD DISPLAY
quick start guide
400EX(n) 460EX(n) 550EX(n)
ii
Introduction
Package Contents
Note
Please make sure the following items are included with your LCD Display.
If any items are missing, contact your dealer.
Contact a local dealer
Note
This stand is not for the Floor Standing Type.
to buy optional items.
Checking the Contents of the Package
Remove the lock from the package box, as shown in the figure above.
Lift up the package box by
holding the grooves on
both sides of the package
box.
Note
After unpacking the package, make sure to check the contents of the package.
•
• Make sure to keep the package box for transporting the product in the future.
• After unpacking, you may use the lower part of the package box as a temporary stand for
product test or operation check.
Check the contents of the
package.
8
Remove the Styrofoam
and vinyl cover.
Unpacking
Introduction
LCD Display
Manuals
Quick Setup Guide Warranty Card
(Not available in all loca-
tions)
MagicInfo Software CD,
MagicInfo Manual CD
(Applicable to the EXn
model only)
Cables
Power Cord D-Sub Cable
Others
User's Guide
Remote Control
(BP59-00138A)
Batteries (AAA X 2)
(Not available in all loca-
tions)
9
HOLDER-WIRE 2EA
(BN61-05373A)
Sold separately
Introduction
LAN Cable USB Cable
RGB to Component Cable
RGB to AV Cable
Your LCD Display
Front
(Applicable to the EXn
model only)
Network Box
(Applicable
to the EX mod-
el only)
RGB to BNC Cable
Wall Mount KIT
SOURCE button
Switches
external device is connected to.
[PC] → [AV] → [Component] → [HDMI] → [MagicInfo]
For an EX model,
• MagicInfo can only be enabled when a network box is connected.
• The HDMI port
from PC mode to Video mode. Selects the input source that an
Note
and network box cannot be connected at the same time.
10
Rear
Introduction
(Power) button
Use this button for turning the LCD Display on and off.
Brightness Sensor
Automatically detects the surrounding brightness.
Power indicator
Shows PowerSaver mode by blinking green
Note
See PowerSaver described in the manual for further information regarding
power saving functions. For energy conservation, turn your LCD Display
OFF when it is not needed or when leaving it unattended for long periods.
Remote Control Sensor
Aim the remote control towards this spot on the LCD Display.
Note
detailed information concerning cable connections, refer to Connecting Cables under
For
Setup. The LCD Display's configuration at the back may vary slightly depending on the model.
11
Note
Applicable to the EXn
model only.
Introduction
POWER S/W ON [ │ ] / OFF
Switches the LCD Display On/Off.
POWER
The power cord plugs into the LCD Display
and the wall outlet.
CMOS CLEAR
Resets MagicInfo.
USB 1 / 2 / 3 (USB Connection Terminal )
Keyboard / Mouse, Mass Storage Device
Compatible.
LAN (LAN Connection Terminal)
Connects to a LAN cable to allow Internet or
network access in MagicInfo mode.
RGB OUT
MagicInfo video output port
RS232C OUT / IN (RS232C Serial
PORT)
MDC(Multiple Display Control) Program Port
RJ 45 MDC (MDC PORT)
MDC(Multiple Display Control) Program Port
12
Introduction
HDMI IN
• Connect the HDMI terminal at the back of
your LCD Display to the HDMI terminal of
your digital output device using a HDMI
cable.
• Up to HDMI 1.0 can be supported.
DVI OUT(LOOPOUT)
• Connect a monitor to another monitor
through a DVI, DVI to HDMI cable.
• Connect the [DVI OUT(LOOPOUT)] port
on the monitor to the [HDMI IN] port on
the other monitor using the DVI to HDMI
cable.
• HDMI and network signals sent via the
[DVI OUT(LOOPOUT)] port are displayed on the second display which has
the DVI IN port.
Note
A maximum of 6 monitors can be connected
to DVI-Loopout. However, up to 10 monitors
can be connected in Full HD mode
depending on the type of cable or signal
equipment connected.
RGB / COMPONENT / AV IN
• Connect the [RGB/COMPONENT/AV IN]
port of the product to the RGB port of the
PC using the D-SUB cable.
• Connect the [RGB / COMPONENT / AV
IN] port on the monitor to the Component
port on the external device using the RGB
to Component cable.
• Connect the [RGB / COMPONENT / AV
IN] port on the monitor to the BNC port on
the PC using the RGB to BNC cable.
• Connect the [RGB / COMPONENT / AV
IN] port on the monitor to the AV port on
the external device using the RGB to AV
cable.
13
Introduction
AUDIO IN
Connect the [AUDIO IN] port on the monitor
to the audio output port on the PC or on the
external device using an audio cable.
AUDIO OUT
Connect a headphone or an External speaker.
Note
[AUDIO OUT] port is only supported for
The
460EX(n) and 550EX(n) models.
Kensington Lock
A Kensington Lock is an anti-theft device that
enables users to lock the product so that they
can safely use it in public locations. Since the
shape and usage of the locking device may
differ depending on the model and the manufacturer, refer to the User Manual supplied
with the locking device for more information.
Note
You
must purchase the Kensington Lock
separately.
To lock the product, follow these
steps:
1. Wrap the Kensington lock cable around
a large, stationary object such as a desk
or chair.
2. Slide the end of the cable with the lock
attached through the looped end of the
Kensington lock cable.
3. Insert the locking device into the Ken-
sington slot on the Monitor (
4.
Lock the lock ( ).
Note
).
• These
instructions, see the User Manual supplied with the locking device.
14
are general instructions. For exact
Loading...