Tips & TricksTo access the contents of this manual while you are
traveling, download an electronic copy from
www.gateway.com/support/manlib/.
1
www.gateway.com
1
Chapter 1: Checking Out Your Gateway Solo 5350
Top
ComponentDescription
Bluetooth indicatorLights up when Bluetooth (if equipped) is turned
on.
ImportantWireless communication can interfere with equipment on
commercial aircraft. Current aviation regulations require
wireless devices to be turned off while traveling in an
airplane. 802.11B and Bluetooth communication devices
are examples of devices that provide wireless
communication.
ImportantIf your system came equipped with an internal wireless
device, please see “Safety, Regulatory, and Legal
Information” on page 33 for general wireless regulatory
and safety guidelines.
Front
ComponentDescription
Cover release latchOpen notebook cover by pressing the release latch.
SpeakersProvide audio output when headphones or speakers are
Hot-swap indicator
Power indicatorLights up when the notebook is turned on and shows
2
not plugged in.
notebook power status:
■
LED steady green - power is ON
■
LED blinking green - power is in Standby or Suspend
mode
■
LED blinking green accompanied by beeping - battery
charge is low
■
LED off - power is off
www.gateway.com
ComponentDescription
Battery charge indicatorLights up when the computer is plugged in.
Left
ComponentDescription
Ethernet jackPlug a 10/100 Ethernet network cable into this optional
FanHelps cool internal components. Do not block or insert
Line in jackConnect an external audio input source (such as a
■
LED green - battery is fully charged and AC is
connected
■
LED orange - battery is charging
■
LED red - battery is low
■
LED off - notebook is running on battery power
jack. For more information, see “Connecting to an
Ethernet network” on page 14.
objects into these slots.
stereo) to this jack so that you can record sound on your
computer or play sound through the notebook speakers.
Left
Headphone jackPlug headphones or amplified speakers into this jack.
Microphone jackPlug a microphone into this jack.
Modem jackPlug a telephone cable into this jack.
PC Card eject buttonPress the eject button to remove a PC Card from the
PC Card slotInsert one Type I, II, or III PC Card into this slot.
Right
ComponentDescription
Modular bayInstall a CD/DVD drive, a second hard drive, or a second
PC Card slot.
battery into this bay.
www.gateway.com
3
Chapter 1: Checking Out Your Gateway Solo 5350
Back
ComponentDescription
Kensington™ lock slotSecure your computer to an object by connecting a
Kensington cable lock to this slot.
PS/2 portPlug a PS/2 device (such as a keyboard or mouse) into
this port.
Parallel portPlug a parallel printer into this port.
TV out jackPlug a TV into this jack so that you can view your
computer screen on a TV using NTSC/PAL composite
video.
Docking connectorConnect the docking station to this connector.
Warning! Power is passed through this connection. This
docking connection is UL certified for use only with Solo
5350 docking stations.
Monitor portPlug an external (VGA) monitor into this port.
USB portsPlug USB (Universal Serial Bus) devices (such as a
USB Iomega™ Zip™ drive, printer, scanner, or camera)
into these ports.
Serial portPlug a serial device (such as a digital camera) into this
port.
Power connectorPlug the AC power adapter cable into this connector.
Bottom
ComponentDescription
Microsoft labelMicrosoft Certificate of Authenticity label includes the
product key code for your operating system.
Module bayUse this bay for a second battery, or a CD, CD-RW, DVD,
diskette, LS-120, or second hard drive.
Module bay latchSlide to release the module.
4
www.gateway.com
Identifying your model
ComponentDescription
Battery latchSlide to release the battery.
Main battery bayInsert the main battery into this bay.
Hard driveThe hard drive is stored here.
Memory bayInstall up to two SO-DIMM memory modules into the slots
held within this bay.
System labelIncludes the product model number and serial number.
Identifying your model
The label on the bottom of your computer contains information that
identifies your notebook model. Technical support will need this information
if you call for assistance. Label information varies by model.
www.gateway.com
5
Chapter 1: Checking Out Your Gateway Solo 5350
Accessories
Gateway offers accessories that can help you make the most of using your
notebook.
Batteries and automobile/airplane power adapters
If you run your notebook on battery power for extended periods, you may
want to buy an additional battery so that you can swap batteries when
necessary.
With an automobile/airplane power adapter, you can save battery power by
plugging your notebook into an automobile cigarette lighter or an airplane
in-flight power receptacle.
Carrying cases
Gateway has large-capacity carrying cases if you need additional space for
accessories or supplies.
External devices
You can attach external devices such as a keyboard, mouse, printer, or monitor
to your notebook.
Memory
Large programs, such as multimedia games or graphics programs, use a lot of
memory. If your programs are running more slowly than you think they
should, try adding more memory.
Printers
You can attach many types of printers to your computer. The most common
types are inkjet and laser printers, which print in color or black and white.
Inkjet printers and cartridges are relatively inexpensive, but usually they are
slower than laser printers. Using an inkjet color printer, you can print pictures,
banners, greeting cards, as well as documents.
Laser printers and cartridges are more expensive, but usually they print much
faster than inkjet printers. Laser printers are better than inkjet printers when
you are printing large documents.
6
www.gateway.com
Getting Started
This chapter provides basic information about your Gateway notebook. Read
this chapter to find out:
■ How to connect the AC power adapter
■ How to start and turn off your notebook
■ How to use the keyboard
■ How to use the EZ Pad™ touchpad
■ How to connect the modem
■ How to connect to a network
■ How to install peripheral devices
2
www.gateway.com
7
Chapter 2: Getting Started
Connecting the AC adapter
You can run your notebook using an AC adapter or the notebook battery. The
battery was shipped to you partially charged. You should use the AC adapter
right away to fully charge the battery. Allow 24 hours for the battery to fully
charge.
ImportantIf the battery is not fully charged before you use your
notebook on battery power for the first time, the battery life
may be much shorter than you expect. If the battery life
seems short even after being charged for 24 hours, the
battery may need to be recalibrated.
To connect the AC adapter:
1 Connect the power cord to the AC adapter, then plug it in to a wall power
outlet.
WarningReplace the power cord if it becomes damaged. The
replacement cord must be of the same type and voltage
rating as the original cord or the notebook may be
damaged.
2 Connect the AC adapter to your notebook’s power connector.
The battery charging indicator light turns on. If the battery charging
indicator light does not turn on, disconnect the adapter from your
notebook and repeat Step 2.
3 When you finish using your notebook the first time, turn the notebook
off and leave the notebook connected to AC power for at least 24 hours.
WarningDo not attempt to disassemble the AC adapter. The
AC adapter has no user-replaceable or user-serviceable
parts inside. The AC adapter has dangerous voltages that
can cause serious injury or death. Contact Gateway about
returning defective AC adapters.
8
www.gateway.com
Starting your notebook
Protecting from power source problems
During a power surge, the voltage level of electricity coming into your
computer can increase to far above normal levels and cause data loss or system
damage. Protect your computer and peripherals by connecting them to a surge
protector, which will absorb voltage surges and prevent them from reaching
your computer.
WarningHigh voltages can enter your computer through both the
power cord and the modem connection. Protect your
computer by using a surge protector. If you have a
telephone modem, use a surge protector that has a
modem jack. If you have a cable modem, use a surge
protector that has an antenna/cable TV jack. During an
electrical storm, unplug both the surge protector and the
modem.
Starting your notebook
To start the notebook:
1 Open your notebook by sliding the latch on the front of your notebook
to the right and lifting the LCD panel.
2 Press the power button located above the keyboard.
The power button is preset to On/Off mode. However, you can also set
it to function in Standby/Resume mode.
3 If you are starting your computer for the first time, follow the on-screen
instructions to set up your computer.
Waking up your notebook
When you have not used your notebook for several minutes, it will go into
a power-saving mode called Standby. While in Standby, the power indicator
light flashes.
If your notebook has gone into Standby mode, “wake” it up by pressing the
power button.
www.gateway.com
9
Chapter 2: Getting Started
Turning off your notebook
To turn off your notebook:
1 Click Start, then select Shut Down. The Shut Down Windows dialog box
opens.
2 Select Shut down.
3 Click OK. Windows shuts down and turns off your notebook.
ImportantIf for some reason you cannot use the Shut down option
in Windows to turn off your notebook, press and hold the
power button for about five seconds.
Using the keyboard
Your notebook features a full-size keyboard that has the full functionality of
a desktop computer keyboard. Many of the keys have been assigned alternate
functions, including shortcut keys for Windows, function keys for specific
system operations, and the Pad Lock keys for the numeric keypad.
Keys
10
You can attach an external keyboard to the notebook using a USB port. You
do not need to shut down the notebook to connect a USB keyboard.
ComponentDescription
Function keysPress these keys labeled F1 to F12 to perform actions
in programs. For example, pressing F1 may open help.
Each program uses different function keys for different
purposes. Refer to the program documentation to find
out more about the function key actions.
Numeric keypadUse these keys to type numbers when Pad Lock is
turned on. Press
System keysPress these green colored keys in combination with
N key to perform a specific action.
the F
www.gateway.com
FN+F9 to turn on the numeric keypad.
Using the keyboard
ComponentDescription
Navigation keysPress these keys to move the cursor to the beginning
of a line, to the end of a line, up the page, down the
page, to the beginning of a document, or to the end
of a document.
N keyPress the FN key in combination with a green or
F
blue-colored system key (such as S
B
LUETOOTH) to perform a specific action.
Windows keyPress to open the Windows Start menu. These keys
can also be used in combination with other keys to
open utilities like F (Search utility), R (Run utility), and
E (Explorer utility).
Application keyPress for quick access to shortcut menus and help
assistants in Windows.
Arrow keysPress these keys to move the cursor up, down, right,
or left.
TANDBY, PAUSE, or
www.gateway.com
11
Chapter 2: Getting Started
Using the multi-function keys
ButtonPress to...
BluetoothTurn Bluetooth on or off.
E-mailOpen your e-mail program.
InternetOpen your Web browser.
HelpOpen online help.
User-defined shortcutOpen the program you assign to this key.
Using the EZ Pad touchpad
The EZ Pad™ consists of a touchpad, two buttons, and a rocker switch.
When you move your finger on the touchpad, the pointer (arrow) on the screen
moves in the same direction.
You can use the EZ-Pad left and right buttons below the touchpad to select
objects. You can scroll, zoom, autoscroll, and pan using the rocker switch
between the touchpad buttons. Scrolling capabilities are available in some
Windows applications, including Microsoft Office.
Using the touchpad
To...Do this...
Move the pointer on the screen.Move your finger around on the touchpad. If
you run out of space on your touchpad and
need to move the pointer farther, lift your
finger, move it to the middle of the touchpad,
then continue moving your finger.
Select an object on the screen.Position the pointer over the object. Press the
left button below the touchpad once. This
action is called clicking.
12
www.gateway.com
Using the EZ Pad touchpad
To...Do this...
Start a program or open a file or folder.Position the pointer over the object. Press the
left button below the touchpad twice in rapid
succession. This action is called
double-clicking.
Access a shortcut menu or find more
information about an object on the
screen.
Move an object on the screen.Position the pointer over the object. Press the
Position the pointer over the object. Quickly
press and release the right button once. This
action is called right-clicking.
left button and hold it down, then use the
touchpad to move (drag) the object to the
appropriate part of the screen. Release the
button to drop the object where you want it.
Using the rocker switch
To...Do this...
Scroll up/downPress forward or backward on the rocker switch to scroll through documents.
Zoom in/outPress and hold Ctrl as you apply pressure to the rocker switch.
Data zoomPress and hold Shift as you rock the switch to jump to a hyperlink or return
to previous Web sites using Internet Explorer or expand or collapse menu
trees in Windows Explorer.
AutoscrollClick both sides of the rocker switch and let go once. The document continues
flowing until you use a keystroke, mouse click, or additional rocker action to
quit scrolling.
PanHold down both sides or the middle of the rocker switch and swipe your finger
across the Touchpad to scroll quickly, either vertically or horizontally. Break
contact with the touchpad to quit scrolling.
www.gateway.com
13
Chapter 2: Getting Started
Connecting the modem
If your notebook has a modem jack, the notebook has a built-in V.92 56K
modem.
CautionTo reduce the risk of fire, use only No. 26 AWG or larger
telecommunications line cord.
To connect the modem:
1 Insert one end of the telephone cable into the modem jack on the right
side of the notebook.
2 Insert the other end of the telephone cable into a telephone wall jack.
The modem will not work with digital or PBX telephone lines.
3 Start your notebook, then start your communications software.
Connecting to an Ethernet network
If your notebook has a network jack, you can connect it to a 10/100 Ethernet
network.
To connect to a network:
1 Insert one end of the network cable into the network jack on the back
of the notebook.
2 Insert the other end of the network cable into a network wall jack. Ask
your network administrator to help you select the correct network jack.
Your notebook is now physically connected to the network. Your network
administrator can help you log onto your network.
Broadband Internet connections
You can use your computer’s Ethernet jack for more than just networking.
Many broadband Internet connections, such as cable modems and DSL
modems, connect to your computer’s Ethernet jack.
14
www.gateway.com
Loading...
+ 36 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.