Samsung 520DX, 520DXn User Guide
SyncMaster 520DX,520DXn
LCD Monitor
User Manual
Safety Instructions
Notational
Note
These safety instructions must be followed
age.
Make sure to read the instructions carefully and use the product in the correct manner.
Warning / Caution
Failure to follow directions noted by this symbol could result in bodily
harm or damage to the equipment.
Notational Conventions
Prohibited
Do not disassemble
Do not touch
to ensure your safety and prevent property dam-
Important to read and understand at all times
Disconnect the plug from the
outlet
Ground to prevent an electric
shock
Power
When not used for extended period of time, set your computer to DPM.
If using screen saver, set it to active screen mode.
The images here are for reference
(or countries).
Shortcut to Anti-Afterimage Instructions
Do not use a damaged power cord or plug or a damaged or
loose power outlet.
• Otherwise, this may result in electric shock or fire.
Do not touch the power plug with wet hands when removing or
plugging the plug into the outlet.
• Otherwise, this may result in electric shock.
Make sure to connect the power cord to a grounded power out-
let.
only, and are not applicable in all cases
Otherwise, it may result in electric shock or personal injury.
•
Safety Instructions
Ensure that the power plug is plugged into the power outlet
firmly and correctly.
•
Otherwise, this may result in fire.
Do not forcefully bend or pull the power plug and do not place
any heavy material on it.
• Otherwise, this may result in fire.
Do not connect multiple appliances to the same power outlet.
• Otherwise, this may cause fire due to overheating.
Do not disconnect the power cord while using the product.
Installation
• Otherwise, this may result in damage
electric shock.
To disconnect the apparatus from the mains, the plug must be
pulled
be readily operable.
• This may cause electric shock or fire.
Use only the power cord provided by our company. Do not use
the provided power cord of another product.
• Otherwise, this may result in fire or electric shock.
Be sure to contact an authorized Service Center when installing your
monitor in a location with heavy
midity, and exposed to chemical substances and where it operates for 24
hours such as at airports, train stations etc.
Failure to do so may cause serious damage to your monitor.
out
from
the
mains
socket,
dust, high or low temperatures, high hu-
therefore the mains plug shall
to the product due to
Ensure that at least two persons lift and move the product.
• Otherwise, it may be dropped and
or damage the product.
When installing the product in a cabinet or rack, make sure that
the front end of the bottom of the product does not project out.
• Otherwise, it may fall or cause personal injury.
• Use a cabinet or rack of a size appropriate to the product.
DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIGARETTES AND ANY HEATING APPLIANCES NEAR THE
PRODUCT.
• Otherwise, this may result in fire.
cause personal injury, and/
Safety Instructions
Keep heating appliances as far away from the power cord or the
product as possible.
•
Otherwise, this may result in electric shock or fire.
Do not install it in a badly ventilated location such as a bookcase
or closet.
• Otherwise, this may result in fire
ternal temperature.
When putting the product down, make sure to put it down softly.
• Otherwise, this may result in damage to the screen display.
Do not place the front of the product on the floor.
• Otherwise, this may result in damage to the screen display.
Ensure that an authorized installation company installs the wall
mount.
• Otherwise, it may fall and cause personal injury.
• Make sure to install the specified wall mount.
Install your product in a well ventilated location. Ensure that
there is a clearance of more than 10 cm from the wall.
• Otherwise, it may result in fire
temperature.
Ensure that the packaging vinyl is kept away from children.
due to an increase in the in-
due to an increase in the internal
Clean
• Otherwise, it may result in serious
play with it.
If the height of your monitor is adjustable, do not place any object or part of your body on the stand when lowering it.
• This
it.
When cleaning the monitor case or the surface of the TFT-LCD screen,
wipe with a slightly moistened, soft fabric.
Do not spray cleaner directly onto the surface of the product.
• Otherwise, this may result in the
the structure and the screen surface may peel off.
Clean the product using a soft cloth with a monitor cleaner only.
you
If
must
with water at a ratio of 1:10.
cause
may
use a cleaner
damage
to
other than the monitor cleaner, dilute it
harm (suffocation) if children
product or the person carrying
the
discoloration and distortion of
Safety Instructions
When cleaning the power plug pins or dusting the power outlet,
clean it with a dry cloth.
•
Otherwise, it may result in fire.
When cleaning the product, make sure to disconnect the power
cord.
• Otherwise, it may result in electric shock or fire.
When cleaning the product, disconnect the power cord and
clean it softly with a dry cloth.
• (Do not use chemicals such as wax, benzene, alcohol, thinner,
mosquito repellant, lubricant, or cleaner.) These may change
the appearance of the product surface and peel off the indication labels on the product.
Since the product housing is easily scratched, make sure to use
the specified cloth only.
• Use the specified cloth adding only a little water. As the product
may be scratched if there is any foreign material on the cloth,
make sure to shake it thoroughly before using it.
When cleaning the product, do not spray water directly onto the
main body of the product.
Others
• Ensure that water does not enter the product and that it is not
wet.
• Otherwise, this may result in electric shock, fire or a malfunc-
tion.
The product is a high voltage product. Ensure that users do not
disassemble, repair or modify the product themselves.
• Otherwise, this may result in electric shock or fire. If the product
needs to be repaired, contact a Service Center.
If there is a strange smell or a strange sound or smoke is coming
from the product, disconnect the power plug immediately and contact a Service Center.
• Otherwise, this may result in electric shock or fire.
Do not place this product in a location exposed to moisture, dust,
smoke, water, or in a car.
• Otherwise, this may result in electric shock or fire.
When you drop the product or the case is broken, turn the power
off and disconnect the power cord. Contact a Service Center.
• Otherwise, this may result in electric shock or fire.
Safety Instructions
If thunder or lightening is occurring, do not touch the power cord
or antenna cable.
•
Otherwise, this may result in electric shock or fire.
Do not try to move the monitor by pulling only the wire or the
signal cable.
• Otherwise, it may fall and result
the product or fire due to damage to the cable.
Do not lift or move the product back and forwards or right and
left while only holding the power cord or signal cables.
• Otherwise, it may fall and result
the product or fire due to damage to the cable.
Make sure that the ventilating opening is not blocked by a table
or curtain.
• Otherwise, it may result in fire
temperature.
Do not place any containers containing water, vases, flowerpots, medicines as well as any metal on the product.
• If water or a foreign material
power cord and contact a Service Center.
• This may result in a product malfunction, electric shock, or fire.
Do not use or keep combustible spray or flammable material
near the product.
• Otherwise, this may result in an explosion or fire.
in electric shock, damage to
in electric shock, damage to
due to an increase in the internal
enters the product, disconnect the
Do not insert any metal, such as chopsticks, coins, pins and
steel, or flammable objects, such as matches or paper, inside the
product (through the ventilating openings, input and output terminals, etc).
• If water or foreign material enters the product, disconnect the
power cord and contact a Service Center.
• Otherwise, this may result in electric shock or fire.
When using a fixed screen for a long time, an afterimage or stain
may occur.
• If you are not using your product for a long period of time, put
it into sleep mode or use a moving screen saver.
Set a resolution and frequency appropriate to the product.
• Otherwise, your eyesight may be damaged.
When using headphones or earphones, do not turn the volume
too high.
• Having the sound too loud may damage your hearing.
Safety Instructions
If you continually move closer to the product screen, your eyesight may be failing.
Take a rest for at least five (5) minutes after using the monitor
for one (1) hour.
This reduces the weariness of your eyes.
Do not install it in an unstable location such as an unstable rack
or uneven surface or a location exposed to vibrations.
• Otherwise, it may fall and cause personal injury and/or damage
the product.
• If you use the product in a location exposed to vibrations, it may
damage the product and result in fire.
When moving the product, turn the power off and disconnect
the power plug, antenna cable, and all the cables connected to the
product.
• Otherwise, it may result in electric shock or fire.
Ensure that children do not hang onto the product or climb up
onto the product.
• The product may fall and cause personal injury or death.
If you do not use the product for a long period of time, disconnect
the power cord from the power outlet.
• Otherwise, this may result in overheating
and may result in fire due to electric shock or leakage.
Do not place any heavy items or toys or confectionery, such as
cookies etc. that may attract the
product.
• Your children may hang onto the product causing it to fall and
this may result in personal injury or death.
Be careful that children do not place the battery in their mouths
when removed from the remote control.
cation that children or infants cannot reach.
• If children have had the battery in their mouths, consult your
doctor immediately.
When replacing the battery, insert it with right polarity (+, -).
attention of children and to the
or fire due to dust,
Place the battery in a lo-
• Otherwise, the battery may become damaged
fire, personal injury or damage due to leakage of the internal
liquid.
Use only the specified standardized batteries, and do not use a
new battery and a used battery at the same time.
• Otherwise, the batteries may be damaged
sonal injury or damage due to a leakage of the internal liquid.
or it may cause
or cause fire, per-
Safety Instructions
The batteries (and rechargeable batteries) are not ordinary refuse
is responsible for returning the used or rechargeable batteries for
recycling.
• The customer can return used or rechargeable batteries to a
Do not place the product in a location exposed to direct sunlight
or near any heat such as a fire or heater.
must
and
nearby public recycling center or to a store selling the same
type of the battery or rechargeable battery.
returned
be
recycling purposes. The customer
for
• This
fire.
Do not drop any objects onto the product or cause any impact
to the product.
•
Otherwise, this may result in electric shock or fire.
Do not use a humidifier or kitchen table near the product.
• Otherwise, this may result in electric shock or fire.
When there is a gas leak, do not touch the product or the power
plug but ventilate immediately.
• If a spark occurs, it may cause an explosion or fire.
If the product has been turned on for a long time, the display
panel becomes hot. Do not touch it.
• Keep the small accessories in a
children.
Be careful when adjusting the angle of the product or the height
of the stand.
may
reduce
the
lifetime
the product, and may result in
of
location out of the reach of
• This may result in personal injury
become caught.
• Also, if you tilt the product too far, it may fall and cause personal
injury.
Do not install the product in a location low enough for children
to reach.
• Otherwise, it may fall and result in personal injury.
• Since the front part
on a level and stable surface.
Do not put any heavy objects on the product.
• This may result in personal injury
uct.
of the product is heavy, install the product
as your hand or fingers may
and/or damage to the prod-
Introduction
Package Contents
Note
Please make sure the following items are included with your LCD Display.
If any items are missing, contact your dealer.
Contact a local dealer
This stand is not for the Floor Standing Type.
Unpacking
to buy optional items.
Note
LCD Display
Manuals
Quick Setup Guide Warranty Card
(Not available in all loca-
tions)
Cables
D-Sub Cable Power Cord
Others
User's Guide
Introduction
Others
Remote Control Batteries (AAA X 2)
(Not available in all loca-
tions)
BNC to RCA Adaptor Jack
Sold separately
DVI Cable Wall Mount KIT LAN Cable
HDD Cover
(Applicable to the DXn
model only)
TV tuner box NetWork Box
(Applicable to the DX mod-
el only)
BNC Cable
Note
• You can purchase and connect a
on how to use these, refer to their respective user manuals.
• You can only connect one external box.
separate network box or TV tuner box. For information
Semi Stand KIT
Your LCD Display
Front
Introduction
MENU button [MENU]
Opens the on-screen menu and exits from the menu. Also use to exit the
OSD menu or return to the previous menu.
Navigate buttons (Up-Down buttons)
Moves from one menu item to another vertically or adjusts selected menu
values.
Adjust buttons (Left-Right buttons) / Volume buttons
Moves from one menu item to another horizontally or adjusts selected
menu values. When OSD is not on the screen, push the button to adjust
volume.
ENTER button [ENTER]
Activates a highlighted menu item.
SOURCE button [SOURCE]
Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the LCD Display at the
time.
[PC] → [DVI] → [AV] → [HDMI] → [MagicInfo] → [TV] → [BNC]→ [Component]
Note
• The TV menu is available when a TV tuner box is installed.
• The MagicInfo
DXn or MP model.
menu is available when a network box is installed in the
D.MENU
Opens the on-screen D.MENU.
Introduction
Note
• This is available when a TV tuner box is installed.
Power button [ ]
Use this button for turning the LCD Display on and off.
Brightness Sensor
The product's Brightness Sensor function automatically detects the surrounding brightness using a brightness sensor and adjusts its brightness
accordingly.
Power indicator
Shows PowerSaver mode by blinking green
Note
Rear
See PowerSaver described in the manual for
power saving functions. For energy conservation, turn your LCD Display
OFF when it is not needed or when leaving it unattended for long periods.
further information regarding
Remote Control Sensor
Aim the remote control towards this spot on the LCD Display.
Note
For
detailed
Setup. The LCD Display 's configuration at the back may vary slightly depending on the LCD
Display model.
information
concerning
cable
connections,
refer to Connecting Cables under
Introduction
POWER S/W ON [ │ ] / OFF [O]
Switches the LCD Display On/Off.
POWER IN
The power cord plugs into the LCD Display
and the wall plug.
RS232C OUT/IN (RS232C Serial PORT)
MDC(Multiple Display Control) Program Port
DVI / PC / HDMI IN [DVI/PC/HDMI AUDIO IN] (PC/DVI/HDMI Audio Connection
Terminal (Input))
DVI / PC / HDMI IN [HDMI]
Connect the HDMI terminal at the back of
your LCD Display to the HDMI terminal of
your digital output device using a HDMI cable.
DVI / PC / HDMI IN [RGB](PC Video
Connection Terminal)
Using a D-Sub Cable (15 pin D-Sub) - PC
mode (Analog PC)
DVI / PC / HDMI IN [DVI] (PC Video Connection Terminal)
Using a DVI Cable (DVI-D to DVI-D) - DVI
mode (Digital PC)
Introduction
DC OUT[5V/1.5A]
Connect this to the power connector of a TV
tuner box or network box.
AV IN [VIDEO] (VIDEO Connection Terminal)
Connect the [ VIDEO ] terminal of your monitor to the video output terminal of the external device using a VIDEO cable.
AV AUDIO IN [L-AUDIO-R](LCD Display
Audio Connection Terminal (Input))
AUDIO OUT [L-AUDIO-R] (LCD Display
Audio Connection Terminal (Output))
BNC/COMPONENT OUT[R/PR, G/Y, B/
PB, H, V]
(BNC/Component Connection Terminal
(Output))
BNC (Analog PC) Connection: connecting
the R, G, B, H, V ports.
Component Connection: connecting the PR,
Y, PB ports.
BNC/COMPONENT IN[R/PR, G/Y, B/
PB, H, V]
(BNC/Component Connection Terminal (Input))
LAN (LAN Connection Terminal)
(Applicable to the DXn model only)
USB(USB Connection Terminal)
Keyboard / Mouse, Mass Storage Device
Compatible.
(Applicable to the DXn model only)
Note
The number of LCD Displays that
connected to loopout may differ depending
on the cables, signal source etc. With cables
can be
Introduction
where there is no degradation or signal
source,
nected.
up
to
ten
LCD
Displays
can be con-
Kensington Lock
The Kensington Lock is a device used to
physically fix the system when using it in a
public place. The locking device has to be
purchased separately. The appearance and
locking method may differ from the illustration depending on the manufacturer. Refer to
the manual provided with the Kensington
Lock for proper use. The locking device has
to be purchased separately.
Note
The location of the Kensington Lock may be
different depending on its model.
Note
See Connecting Cables for further information regarding cable connections.
Remote Control
Note
The performance of the remote control may be affected by a TV or other electronic device
operating near the LCD Display , causing a malfunction due to interference with the frequency.
Using the Anti-Theft Kensington Lock
1. Insert the locking device into the Ken-
sington slot on the Monitor and turn
it in the locking direction
2.
Connect the Kensington Lock cable.
Fix
3.
heavy stationary object.
Kensington
the
Lock
.
to a desk or a
Introduction
POWER
OFF
Number Buttons
DEL button
+ VOL -
MUTE
TV/DTV
MENU
INFO
COLOR BUTTONS
TTX/MIX
STILL
AUTO
S.MODE
MDC
LOCK
SOURCE
ENTER/PRE-CH
CH/P
D.MENU
GUIDE
RETURN
Up-Down Left-Right buttons
EXIT
SRS
MagicInfo
P.MODE
DUAL/MTS
PIP
1.
2. Off
3. Number Buttons
4. DEL button
POWER
SWAP
Turns the product On.
Turns the product Off.
Press to change the channel.
The "-" button operates only for
MMS (multi-channel) for a DTV.
DTV. It is used to select
Introduction
5. + VOL - Adjusts the audio volume.
6. MUTE
7. TV/DTV Selects the TV and DTV mode directly.
MENU
8.
9.
10. INFO
11.COLOR BUTTONS Press to add or delete channels and to store channels to the
12.
TTX/MIX
Pauses (mutes) the audio output temporarily.
played on the lower left corner of the screen. The audio
resumes if MUTE or - VOL + is pressed in the Mute mode.
Opens the on-screen menu and exits
closes the adjustment menu.
Activates a highlighted menu item.
Current picture information is displayed on
corner of the screen.
favorite channel list in the “Channel List” menu.
TV channels provide written information services via teletext.
- Teletext Buttons
For more information > TTX / MIX
from the menu or
This is dis-
the upper left
13.STILL Press the button once to freeze
to unfreeze.
14.AUTO Adjusts the screen display automatically in PC mode. By
changing the resolution in the control panel, auto function is
performed.
15. S.MODE When pressing this button, the current mode is displayed at
the bottom centre of the screen. The LCD Display has a
built-in high fidelity stereo amplifier. Then press the button
again to circle through available preconfigured modes.
( Standard → Music → Movie → Speech → Custom )
16.MDC MDC Quick Launch Button.
17.LOCK Activates or deactivates all function keys on both the remote
control and the LCD Display except for the Power and LOCK
buttons.
SOURCE
18.
ENTER/PRE-CH
19.
Press the button to change the input signal SOURCE.
Changing the SOURCE is only allowed
that are connected to the monitor at the time.
This button is used to return
channel.
the screen. Press it again
for external devices
to the immediately previous
20.
CH/P In TV mode, selects TV channels.
21.D.MENU
22.GUIDE
DTV menu display
Electronic Program Guide (EPG) display.
Introduction
23. RETURN
24. Up-Down Left-Right but-
tons
25.
26. SRS
27.MagicInfo MagicInfo Quick Launch Button.
28. P.MODE When you press this button,
EXIT
Returns to the previous menu.
Moves from one
or adjusts selected menu values.
Exits from the menu screen.
Selects SRS TruSurround XT mode.
played on the lower center of the screen.
menu item to another horizontally, vertically
current picture mode is dis-
AV / HDMI / TV : P.MODE
The LCD Display has four automatic picture settings that are
preset at the factory. Then push button again to circle
through available preconfigured modes. ( Dynamic →
Standard → Movie → Custom )
PC / DVI / MagicInfo: M/B (MagicBright)
29.
30.
PIP
DUAL/MTS
MagicBright is a feature providing the optimum viewing environment depending on the contents of the image you are
watching. Then push button again to circle through available
preconfigured modes. (Entertain → Internet → Text → Cus-
tom )
DUAL-
STEREO/MONO, DUAL l / DUAL ll and MONO/NICAM
MONO/NICAM STEREO can be operated depending on the
broadcasting type by using the DUAL button on the remote
control while watching TV.
MTS-
You can select MTS (Multichannel Television Stereo) mode.
Audio Type MTS/S_Mode Default
FM Stereo Mono Mono Manual
Stereo Mono ↔ Stereo
SAP Mono ↔ SAP Mono
Every time you press the button, a PIP screen appears.
Change
31.
SWAP
- This fuction does not work for this LCD Display.
Swaps the contents of the PIP and main image. The image
in the PIP window will appear on the main screen, and the
main screen image will appear in the PIP window.
- This fuction does not work for this LCD Display.
Mechanical Layout(520DX(N))
Mechanical Layout
Introduction
LCD Display Head
NETWORK MODEL SIZE
Introduction
Installation VESA Bracket
• When installing VESA, make sure to comply with the international VESA standards.
• Purchasing VESA Bracket and
SAMSUNG Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket.
• At least 2 persons are needed in order to move the LCD Display.
• SAMSUNG is not responsible for any product damage or any injury caused by installation
at customer's discretion.
Installation Information : Please contact your nearest
Dimensions
Introduction
Notice
For securing the bracket on a
mm length.
Wall Bracket Installation
• Contact a technician for installing the wall bracket.
• SAMSUNG Electronics is not responsible for any damages to the product or harm to
customers when the installation is done by the customer.
• This product is for installing on cement walls. The product may not stay in place when
installed on plaster or wood.
Components
Only use the components and accessories shipped with the product.
wall, use only machine screws of 6 mm diameter and 8 to 12
Wall Bracket(1) Hinge(Left 1, Right1)Plastic
Wall Bracket Assembly
Note
There are two hinges(left and right). Use the correct one.
Hanger
(4)
Screw
(A)(11)
Screw
(B)(4)
Anchor
(11)
Introduction
1. Insert and tighten the Captive Screw in the direction of the arrow.
When done, mount the wall bracket on the wall.
There are two hinges(left and right). Use the correct one.
A - Captive Screw
B - Wall Bracket
C - Hinge (Left)
D - Hinge (Right)
2. Before
of the product is correct.
If the length is too short or long, loosen all or some of the 4screws on the wall bracket to
adjust the length.
drilling into the wall, check
if the length between the two locking holes at the back
A - Length between the two locking holes
3. Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit
to drill holes deeper than 35
of the brackets and hinge holes to the corresponding anchor holes and insert and tighten
the 11 screws A.
mm. Fix each anchor in the corresponding hole. Match each
Introduction
To mount the product on the wall bracket
The shape of the product may
hanger and the screw are the same)
1. Remove the 4 screws on the back of the product.
2. Insert the screw B into the plastic hanger.
Notice
vary depending on the model. (The assemblies of the plastic
• Mount
and right plastic hangers.
• Be careful when installing the product on the bracket as fingers can be caught in the
holes.
• Make sure the wall bracket is securely fixed to the wall, or the product may not stay
in place after installation.
3. Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product.
the
product
on
the
wall
bracket and make sure it is properly fixed to the left
Introduction
4. Remove safety pin (3) and insert
holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to
re-insert and tighten the safety pin (3) to securely hold the product to the bracket.
A - LCD Display
B - Wall Bracket
C - Wall
Wall Bracket Angle Adjustment
Adjust the bracket angle to -2° before installing it on the wall.
the 4 product holders into the corresponding bracket
1. Fix the product to the wall bracket.
2. Hold the product at the top
adjust the angle.
Note
You can adjust the bracket angle between -2° and 15°.
in the center and pull it forward (direction of the arrow) to
Introduction
Make sure to use the top center, and not the leftor the right side of the product to adjust the
angle.
Connections
Connecting a Computer
Using a Power cord with Earth
• In the event of failure, the
sure to wire the earth lead in correctly, before connecting the AC power.
When un-wiring the earth lead, make sure to disconnect the AC power
in advance.
Note
AV input devices such as DVD
be connected to the LCD Display. For detailed information on connecting AV input devices,
refer to the contents under Adjusting Your LCD Display.
earth lead may cause electric shock. Make
players, VCRs or camcorders as well as your computer can
Connect the power cord for your LCD Display to the power port on the back
of the LCD Display. Turn on the power switch.
There are 3 ways to connect the D-sub to your LCD Display. Choose one
of the following:
Using the D-sub (Analog) connector on the video card.
• Connect the D-sub to the 15-pin,
Display and the 15 pin D-sub Port on the computer.
Using the DVI (Digital) connector on the video card.
• Connect the DVI Cable to the
and the DVI port on the computer.
RGB port on the back of your LCD
DVI port on the back of your LCD Display
Connections
Note
• Turn on both your computer and the LCD Display.
• The DVI cable is optional.
• Contact a local SAMSUNG Electronics Service Center to buy optional items.
Using the BNC (Analog) connector on the video card.
• Connect the BNC Cable to the BNC/COMPONENT IN - R, G, B, H, V
ports on the back of your LCD Display and the 15 pin D-sub Port on
the computer.
Connect the audio cable for your LCD Display to the audio port on the back
of your computer.
Connecting to Other devices
Using a Power cord with Earth
• In the event of failure, the
sure to wire the earth lead in correctly, before connecting the AC power.
When un-wiring the earth lead, make sure to disconnect the AC power
in advance.
Note
AV input devices such as DVD
be connected to the LCD Display. For detailed information on connecting AV input devices,
refer to the contents under Adjusting Your LCD Display.
Connecting AV Devices
earth lead may cause electric shock. Make
players, VCRs or camcorders as well as your computer can
Connections
1. Connect
the LCD Display.
2. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted.
3. Select AV using the SOURCE .
Note
The LCD Display has AV connection
or Camcorders. You may enjoy AV signals as long as the LCD Display is turned on.
the
port
Connecting to a Camcorder
of
the
VCR (DVD / DTV Set-Top Box) to the [R-AUDIO-L] port of
DVD,
terminals to connect AV input devices like DVDs, VCRs
1. Locate the AV output jacks on
of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on
the camcorder and the AV AUDIO IN [L-AUDIO-R] on the LCD Display .
2. Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV
IN [VIDEO] on the LCD Display .
3. Select AV for the Camcorder connection using the Source button on the front of the LCD
Display or on the remote control.
4. Then, start the Camcorders with a tape inserted.
Note
The audio-video cables shown here are
your local electronics store.) If your camcorder is stereo, you need to connect a set of two
cables.
the camcorder. They are usually found on the side or back
usually included with a Camcorder. (If not, check
Connecting a DVD Player
Connections
1. Connect a set of audio cables
play and the AUDIO OUT jacks on the DVD player.
2. Connect a Component cable between the BNC/COMPONENT IN - PR, Y, PB port on the
LCD Display and the PR, Y, PB jacks on the DVD player.
Note
• Select Component for the connection to a DVD player using the SOURCE button on the
front of the LCD Display or on the remote control.
• Then, start the DVD Player with a DVD disc inserted.
Note
• A component cable is optional.
For an explanation of Component video, consult your DVD manual.
Connecting a DTV Set Top Box
Note
The connections for a typical Set Top Box are shown below.
•
between the AV AUDIO IN [L-AUDIO-R] on the LCD Dis-
Connections
1. Connect a Component
the LCD Display and the PR, Y, PB jacks on the Set Top Box.
2. Connect a set of audio cables between the AV AUDIO IN [L-AUDIO-R] on the LCD Display and the AUDIO OUT jacks on the Set Top Box.
Note
• Select Component for the connection to
on the front of the LCD Display or on the remote control.
Note
• For an explanation of Component video, see your Set Top Box owner's manual.
Connecting Using a HDMI Cable
cable
between
the
BNC / COMPONENT IN - PR, Y, PB port on
a DTV Set Top Box using the SOURCE button
Note
• Input devices such as digital DVD
using the HDMI cable.
• You cannot connect a PC to the HDMI terminal.
are connected to the HDMI terminal of the LCD Display
Loading...