Samsung 400TS-3 User Manual

SyncMaster 400TS-3, 460TS-3

LCD Display

User Manuals

The color and the appearance may differ depending on the
product, and the specifications are subject to change
without prior notice to improve the performance.

Safety Instructions

Notational

Note

These safety instructions must be followed to ensure your safety and prevent property damage.

Make sure to read the instructions carefully and use the product in the correct manner.

Warning / Caution

Failure to follow directions noted by this symbol could result in bodily harm
or damage to the equipment.

Note

Power

Prohibited

Do not disassemble

Do not touch

When not used for extended period of time, set your computer to DPM.

If using a screen saver, set it to active screen mode.

The images here are for reference only, and are not applicable in all cases (or
countries).

Shortcut to Anti-Afterimage Instructions

Do not use a damaged power cord or plug or a damaged or loose power

outlet.

• Otherwise, this may result in electric shock or fire.

Important to read and under­stand at all times

Disconnect the plug from the
outlet

Ground to prevent an electric
shock

Do not touch the power plug with wet hands when removing or plug-

ging the plug into the outlet.

• Otherwise, this may result in electric shock.

Make sure to connect the power cord to a grounded power outlet.

• Otherwise, it may result in electric shock or personal injury.

Ensure that the power plug is plugged into the power outlet firmly and

correctly.

• Otherwise, this may result in fire.

Safety Instructions

Do not forcefully bend or pull the power plug and do not place any

heavy material on it.

• Otherwise, this may result in fire.

Do not connect multiple appliances to the same power outlet.

• Otherwise, this may cause fire due to overheating.

Do not disconnect the power cord while using the product.

• Otherwise, this may result in damage to the product due to electric
shock.

To disconnect the apparatus from the mains, the plug must be pulled
out from the mains socket, therefore the mains plug shall be readily op­erable.

• Otherwise, this may cause electric shock or fire.

Use only the power cord provided by our company. Do not use the
provided power cord of another product.

Installation

• Otherwise, this may result in fire or electric shock.

Connect the power plug to a wall outlet that can be easily reached.

• When a problem occurs with the product, you must unplug the power

plug to cut the power off completely. You cannot cut the power off
completely using only the power button on the product.

Be sure to contact an authorized Service Center when installing your monitor in
a location with heavy dust, high or low temperatures, high humidity, and exposed
to chemical substances and where it operates for 24 hours such as at airports,
train stations etc.

Failure to do so may cause serious damage to your monitor.

Ensure that at least two persons lift and move the product.

• Otherwise, it may be dropped and cause personal injury, and/or dam-

age the product.

When installing the product in a cabinet or rack, make sure that the
front end of the bottom of the product does not project out.

• Otherwise, it may fall or cause personal injury.

• Use a cabinet or rack of a size appropriate to the product.

DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIGA­RETTES AND ANY HEATING APPLIANCES NEAR THE PROD­UCT.

• Otherwise, this may result in fire.

Safety Instructions

Keep heating appliances as far away from the power cord or the prod­uct as possible.

• Otherwise, this may result in electric shock or fire.

Do not install it in a badly ventilated location such as a bookcase or
closet.

• Otherwise, this may result in fire due to an increase in the internal

temperature.

When putting the product down, make sure to put it down softly.

• Otherwise, this may result in damage to the screen display.

Do not place the front of the product on the floor.

• Otherwise, this may result in damage to the screen display.

Ensure that an authorized installation company installs the wall mount.

• Otherwise, it may fall and cause personal injury.

• Make sure to install the specified wall mount.

Install your product in a well ventilated location. Ensure that there is
a clearance of more than 4 inches (10 cm) from the wall.

• Otherwise, it may result in fire due to an increase in the internal tem-

perature.

Bend the outdoor antenna cable downwards at the location where it
goes in so that rainwater does not flow in.

• If rainwater enters the product, it may result in electric shock or fire.

Install the antenna far away from any high voltage cables.

• If the antenna touches or falls onto a high voltage cable, it may result

in electric shock or fire.

Ensure that the packaging vinyl is kept away from children.

• Otherwise, it may result in serious harm (suffocation) if children play

with it.

If the height of your monitor is adjustable, do not place any object or
part of your body on the stand when lowering it.

Clean

• This may cause damage to the product or the person carrying it.

When cleaning the monitor case or the surface of the TFT-LCD screen, wipe
with a slightly moistened, soft cloth.

Safety Instructions

Do not spray cleaner directly onto the surface of the product.

• Otherwise, this may result in the discoloration and distortion of the

structure and the screen surface may peel off.

When cleaning the power plug pins or dusting the power outlet, clean
it with a dry cloth.

• Otherwise, it may result in fire.

When cleaning the product, make sure to disconnect the power cord.

• Otherwise, it may result in electric shock or fire.

When cleaning the product, disconnect the power cord and clean it
with a soft, dry cloth.

• (Do not use chemicals such as wax, benzene, alcohol, thinner, mos-

quito repellant, lubricant, or cleaner.) These may change the appear­ance of the product surface and peel off the indication labels on the
product.

Since the product housing is easily scratched, make sure to use the
specified cloth only.

Others

When cleaning the product, do not spray water directly onto the main
body of the product.

• Ensure that water does not enter the product and that it is not wet.

• Otherwise, this may result in electric shock, fire or a malfunction.

The product is a high voltage product. Do not disassemble, repair or
modify the product yourself.

• Otherwise, this may result in electric shock or fire. If the product

needs to be repaired, contact a Service Center.

If there is a strange smell or a strange sound or smoke is coming from
the product, disconnect the power plug immediately and contact a Service
Center.

• Otherwise, this may result in electric shock or fire.

Do not place this product in a location exposed to moisture, dust,
smoke, water, or in a car.

• Otherwise, this may result in electric shock or fire.

When you drop the product or the case is broken, turn the power off
and disconnect the power cord. Contact a Service Center.

• Otherwise, this may result in electric shock or fire.

Safety Instructions

If thunder or lightning is occurring, do not touch the power cord or
antenna cable.

• Otherwise, this may result in electric shock or fire.

Do not try to move the monitor by pulling only the wire or the signal
cable.

• Otherwise, it may fall and result in electric shock, damage to the

product or fire due to damage to the cable.

Do not lift or move the product back and forwards or right and left
while only holding the power cord or signal cables.

• Otherwise, it may fall and result in electric shock, damage to the

product or fire due to damage to the cable.

Make sure that the ventilating opening is not blocked by a table or
curtain.

• Otherwise, it may result in fire due to an increase in the internal tem-

perature.

Do not place any containers containing water, vases, flowerpots, med­icines as well as any metal on the product.

• If water or a foreign material enters the product, disconnect the power

cord and contact a Service Center.

• This may result in a product malfunction, electric shock, or fire.

Do not use or keep combustible spray or flammable material near the
product.

• Otherwise, this may result in an explosion or fire.

Do not insert any metal, such as chopsticks, coins, pins and steel, or
flammable objects, such as matches or paper, inside the product (through
the ventilating openings, input and output terminals, etc).

• If water or foreign material enters the product, disconnect the power

cord and contact a Service Center.

• Otherwise, this may result in electric shock or fire.

When using a fixed screen for a long time, an afterimage or stain may
occur.

• If you are not using your product for a long period of time, put it into

sleep mode or use a moving screen saver.

Set a resolution and frequency appropriate to the product.

• Otherwise, your eyesight may be damaged.

When using headphones or earphones, do not turn the volume too high.

• Having the sound too loud may damage your hearing.

Safety Instructions

To avoid eyestrain, do not sit too close to the product.

Take a rest for at least five (5) minutes after using the monitor for one
(1) hour.

This reduces eye fatigue.

Do not install it in an unstable location such as an unstable rack or
uneven surface or a location exposed to vibrations.

• Otherwise, it may fall and cause personal injury and/or damage the

product.

• If you use the product in a location exposed to vibrations, it may

damage the product and result in fire.

When moving the product, turn the power off and disconnect the power
plug, antenna cable, and all the cables connected to the product.

• Otherwise, it may result in electric shock or fire.

Ensure that children do not hang onto the product or climb up onto the
product.

• The product may fall and cause personal injury or death.

If you do not use the product for a long period of time, disconnect the
power cord from the power outlet.

• Otherwise, this may result in overheating or fire due to dust, and may

result in fire due to electric shock or leakage.

Do not place any heavy items or toys or confectionery, such as cookies
etc. that may attract the attention of children and to the product.

• Your children may hang onto the product causing it to fall and this

may result in personal injury or death.

Be careful that children do not place the battery in their mouths when
removed from the remote control. Place the battery in a location that
children or infants cannot reach.

• If children have had the battery in their mouths, consult your doctor

immediately.

When replacing the battery, insert it with the right polarity (+, -).

• Otherwise, the battery may become damaged or it may cause fire,

personal injury or damage due to leakage of the internal liquid.

Use only the specified standardized batteries, and do not use a new
battery and a used battery at the same time.

• Otherwise, the batteries may be damaged or cause fire, personal in-

jury or damage due to a leakage of the internal liquid.

Safety Instructions

The batteries (and rechargeable batteries) are not ordinary refuse and
must be returned for recycling purposes. The customer is responsible for
returning the used or rechargeable batteries for recycling.

• The customer can return used or rechargeable batteries to a nearby

public recycling center or to a store selling the same type of the battery
or rechargeable battery.

Do not place the product in a location exposed to direct sunlight or
near any heat such as a fire or heater.

• This may reduce the lifetime of the product, and may result in fire.

Do not drop any objects onto the product or cause any impact to the
product.

• Otherwise, this may result in electric shock or fire.

Do not use a humidifier near the product.

• Otherwise, this may result in electric shock or fire.

When there is a gas leak, do not touch the product or the power plug;
ventilate immediately.

• If a spark occurs, it may cause an explosion or fire.

If the product has been turned on for a long time, the display panel
becomes hot. Do not touch it.

Keep the small accessories in a location out of the reach of children.

Be careful when adjusting the angle of the product or the height of the
stand.

• This may result in personal injury as your hand or fingers may be-

come caught.

• Also, if you tilt the product too far, it may fall and cause personal

injury.

Do not install the product in a location low enough for children to
reach.

• Otherwise, it may fall and result in personal injury.

• Since the front part of the product is heavy, install the product on a

level and stable surface.

Do not put any heavy objects on the product.

• This may result in personal injury and/or damage to the product.

Introduction

Package Contents

Checking the Contents of the Package

Remove the lock from the package box, as shown in the figure above.

holding the grooves on both

• After unpacking the package, make sure to check the contents of the package.

• Store the packaging box in case you need to move the Product later.

• If any items are missing, contact your dealer.

• Contact a local dealer to purchase optional items.

Unpacking

Lift up the package box by

sides of the package box.

Note

Check the contents of the

package.

Remove the Styrofoam and

vinyl cover.

LCD Display

Manuals

Introduction

Quick Setup Guide Warranty Card

(Not available in all loca-

Cables

Power Cord D-Sub Cable USB Cable

Others

Remote Control

Batteries (AAA X 2)

User's Guide

tions)

(BP59-00138B)

Sold separately

Semi Stand KIT LAN Cable

RGB to BNC Cable RGB to COMPONENT Ca-

(Not available in all loca-

tions)

ble

Network Box

Sold separately

Wall Mount KIT TV Tuner box RS232C Cable

Note

• Accessories that can be purchased with the product vary by country.

Your LCD Display

The color and the appearance may differ depending on the product, and the specifications are subject
to change without prior notice to improve the performance.

Front

Introduction

MENU button [MENU]

Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu
or return to the previous menu.

Navigate buttons (Up-Down buttons)

Moves from one menu item to another vertically or adjusts selected menu values.

Adjust buttons (Left-Right buttons) / Volume buttons

Moves from one menu item to another horizontally or adjusts selected menu val­ues. When OSD is not on the screen, press the button to adjust volume.

ENTER button [ENTER]

Activates a highlighted menu item.

SOURCE button [SOURCE]

Switches from PC mode to Video mode. Selects the input source that an external
device is connected to.

[PC] → [DVI] → [AV] → [Component] → [HDMI1] → [HDMI2] → [Dis-

playPort] → [MagicInfo] →[TV]

Note

• The [RGB/COMPONENT IN] port is compatible with RGB (PC) and Com­ponent signals.

Introduction

However, the picture may display abnormally if the connected external input
signal is different from the selected video signal.

• MagicInfo can only be enabled when a network box is connected.

• A TV tuner box (sold separately) must be connected to use the TV.

D.MENU button

Opens the on-screen D.MENU.

Note

The D.MENU button is activated when a TV tuner is connected and otherwise, the
PIP button is enabled.

PIP button

Push the PIP button to turn the PIP screen On / Off.

Power button [ ]

Use this button for turning the LCD Display on and off.

Brightness Sensor

Rear

Automatically detects the surrounding brightness.

Power indicator

Shows PowerSaver mode by blinking green

Note

See PowerSaver described in the manual for further information regarding power
saving functions. For energy conservation, turn your LCD Display OFF when it
is not needed or when leaving it unattended for long periods.

Remote Control Sensor

Aim the remote control towards this spot on the LCD Display.

Note

See the "Connections" section for details about cable connections. The LCD Display's configuration
at the back may vary slightly depending on the model.

Introduction

POWER S/W ON [ I ] / OFF

Switches the LCD Display On/Off.

POWER

The power cord plugs into the LCD Display and
the wall outlet.

TOUCH SCREEN USB HUB

Connects to a network box (sold separately) or PC
in order to use the touchscreen.

To use the touchscreen, install the touchscreen
driver.

RGB/COMPONENT IN (PC/COMPONENT

Connection Terminal (Input))

• Connect the [RGB/COMPONENT IN] port
on the monitor to the RGB port on the PC us­ing the D-SUB cable.

• Connect the [RGB/COMPONENT IN] port
on the monitor to the COMPONENT port on
the external device using the RGB to COM­PONENT cable.

• Connect the [RGB/COMPONENT IN] port
on the monitor to the BNC port on the PC us­ing the RGB to BNC cable.

DVI IN (PC Video Connection Terminal)

Connect the [DVI IN] port on the monitor to the
DVI port on the PC using the DVI cable.

RGB/DVI/DP/HDMI AUDIO IN (PC/DVI/

DP/HDMI Audio Connection Terminal (Input))

Connect the [RGB/DVI/DP/HDMI AUDIO IN]
terminal of the monitor and the speaker output
terminal of your computer's so und card using a
stereo cable (sold separately).

DP IN

Receives a signal from the Display port.

Connect a DP cable to [DP IN] on the product and
DP IN on another display.

Introduction

AV/COMPONENT AUDIO IN [R-AUDIO-L]

Connect the [AV/COMPONENT AUDIO IN [R-
AUDIO-L]] port on the monitor to the audio
output port on the PC or on the external device
using an audio cable.

AV IN

Connect the [AV IN] terminal of your monitor to
the video output terminal of the external device
using a VIDEO cable.

AUDIO OUT

Connect a headphone or an External speaker.

DC OUT

Make sure to use connecting [DC OUT] terminal
to the authorized TV-Tuner Box[SBB_DTC/
ZA].

Otherwise, this may result in damage to

the product.

HDMI IN 1

• Connect the [HDMI IN 1] terminal at the back
of your LCD Display to the HDMI terminal
of your digital output device using a HDMI
cable.

• Up to HDMI 1.3 can be supported.

Note

• A normal external device (DVD player or
camcorder, etc.) or a TV tuner box can be
connected to the [HDMI IN 1] terminal.

• To use a TV tuner box, make sure to connect
it to the [HDMI IN 1] terminal.

HDMI IN 2 (MAGICINFO)

• Connect the [HDMI IN 2 (MAGICINFO)]
terminal at the back of your LCD Display to
the HDMI terminal of your digital output de­vice using a HDMI cable.

• Up to HDMI 1.3 can be supported.

Note

To use MagicInfo, the network box specified
separately by Samsung must be installed inside

Introduction

the product and the MagicInfo output of the net­work box must be connected to the [HDMI IN 2
(MAGICINFO)] terminal.

For more information on how to purchase and in­stall a network box, contact Samsung Electronics.

RJ 45 MDC (MDC PORT)

MDC(Multiple Display Control) Program Port

Connect the LAN cable to [RJ45 MDC] on the
product and LAN on the PC. To use an MDC, the
MDC Program must be installed on the PC.

Note

Go to Multi Control and select RJ45 MDC as
the MDC Connection.

RS232C OUT/IN (RS232C Serial PORT)

MDC(Multiple Display Control) Program Port

Connect a serial cable (cross type) to [RS232C]
on the product and RS232C on the PC. To use an
MDC, the MDC Program must be installed on the
PC.

Note

Go to Multi Control and select RS232C MDC
as the MDC Connection.

Kensington Lock slot

A Kensington Lock is an anti-theft device that
enables users to lock the product so that they can
safely use it in public locations. Since the shape
and usage of the locking device may differ de­pending on the model and the manufacturer, for
more information, refer to the User Manual sup­plied with the locking device for more informa­tion.

Note

You must purchase the Kensington Lock sepa­rately.

To lock the product, follow these steps:

1. Wrap the Kensington lock cable around a

large, stationary object such as a desk or
chair.

Introduction

2. Slide the end of the cable with the lock at-

tached through the looped end of the Ken­sington lock cable.

3. Insert the Kensington Lock into the security

slot ( ) on the back of the display.

4.

Lock the lock ( ).

Note

• These are general instructions. For exact in­structions, see the User Manual supplied with
the locking device.

• You can purchase the locking device from an
electronics store, an online shop, or our serv­ice Center.

Connecting a Network Box (sold separately)

RGB OUT

MagicInfo video output port

MAGICINFO OUT

It can be used by connecting it to the [HDMI IN
2 (MAGICINFO)] terminal using a DP to HDMI
cable.

LAN (LAN Connection Terminal)

Connects to a LAN cable to allow Internet or net­work access in MagicInfo mode.

Connecting a Network Box (sold separately)

USB (USB Connection Terminal)

Keyboard / Mouse, Mass Storage Device Com­patible.

AUDIO OUT

Connect a headphone or an External speaker.

RS232C (RS232C Serial PORT)

Serial port

Connecting a Network Box (sold separately)

Introduction

POWER

Connect the [POWER] terminal of the product
and the [POWER] terminal of the monitor using
a power extension cable.

POWER

Connects to a mains socket via the power cord.

POWER S/W ON [ I ] / OFF

Turns the network box on or off.

Note

• See the "Connections" section for details about cable connections.

• The power switches of both of the monitor and the network box must be turned on for the network
box to operate normally.

Remote Control

Note

The performance of the remote control may be affected by a TV or other electronic device operating
near the LCD Display, causing a malfunction due to interference with the frequency.

POWER

OFF

Number Buttons

DEL / GUIDE button

+ VOL -

SOURCE

D.MENU

TOOLS

Up-Down Left-Right buttons

INFO

The Color button and the PC/DVI/HDMI/DP
selection button.

TTX/MIX

MTS/DUAL

ENTER/PRE-CH

MUTE

CH/P

TV

Introduction

MENU

RETURN

EXIT

MagicInfo

POWER

OFF

Number Buttons

DEL / GUIDE button

+ VOL -

SOURCE

Turns the product On.

Turns the product Off.

Used to enter the password during the OSD adjustment or to use
MagicInfo.

Press to change the channel.

The "-" button is used to select Digital channels.

Electronic Program Guide (EPG) display.

Note

This button can only be used in TV mode while a TV tuner box
(sold separately) is connected.

Adjusts the audio volume.

Selects a connected external input source or MagicInfo mode.

Press the button to change the input signal SOURCE.

D.MENU

TOOLS

Up-Down Left-Right but-

tons

INFO

The Color button and the
PC/DVI/HDMI/DP selection
button.

Changing the SOURCE is only allowed for external devices that
are connected to the LCD Display at the time.

DTV menu display

Note

This button can only be used in TV mode while a TV tuner box
(sold separately) is connected.

Use to quickly select frequently used functions.

Note

This function does not work for this LCD Display.

Moves from one menu item to another horizontally, vertically or
adjusts selected menu values.

Current picture information is displayed on the upper left corner
of the screen.

In TV mode, these buttons can be used to configure a list of chan­nels.

Introduction

You can select the PC, DVI, HDMI or DP(DisplayPort) external
input directly in a mode other than TV mode.

TTX/MIX

MTS/DUAL

TV channels provide written information services via teletext.

- Teletext Buttons

Note

This function does not work for this LCD Display.

MTS-

You can select MTS (Multichannel Television Stereo) mode.

Audio Type MTS/S_Mode Default

FM Stereo Mono Mono Manual Change

Stereo

SAP

DUAL-

STEREO/MONO, DUAL l / DUAL ll and MONO/NICAM
MONO/NICAM STEREO can be operated depending on the
broadcasting type by using the DUAL button on the remote control
while watching TV.

Mono ↔ Stereo

Mono ↔ SAP

Mono

ENTER/PRE-CH

MUTE

CH/P

TV

Note

Enabled when a TV tuner box is connected.

This button is used to return to the immediately previous channel.

Note

Enabled when a TV tuner box is connected.

Pauses (mutes) the audio output temporarily. This is displayed on
the lower left corner of the screen. The audio comes back on if
MUTE or - VOL + is pressed in the Mute mode.

In TV mode, selects TV channels.

Note

Enabled when a TV tuner box is connected.

Allows you to watch an analogue or digital TV.

Note

MENU

Enabled when a TV tuner box is connected.

Opens the on-screen menu and exits from the menu or closes the
adjustment menu.

Introduction

RETURN

EXIT

MagicInfo

User Installation Guide

Note

• Be sure to call an installation expert of Samsung Electronics to install the product.

• The warranty becomes invalid if the product is installed by someone other than a professional

authorized by Samsung Electronics.

• A Samsung Electronics service center can provide details.

Tilt Angle and Rotation

Returns to the previous menu.

Exits from the menu screen.

MagicInfo Quick Launch Button.

Note

Enabled when a Network box is connected.

1 2

1. The product can be tilted up to 15 degrees from a vertical wall.

2. To use the product in portrait mode, rotate it clockwise so that the LED indicator is at the bottom.

Ventilation requirement

1. Vertical wall mount condition

<Side view>

Introduction

A : min. 40 mm

B: Ambient temperature Measuring point < 35°C

• When installing the product onto a vertical wall, be sure there is a 40 mm space or more behind

the product for ventilation, as shown above, and maintain the ambient temperature at 35°C or lower.

Note

A Samsung Electronics service center can provide details.

2. Embedded Mount guide

<Side view> <Top view>

A : min. 40 mm

B : min. 70 mm

C : min. 50 mm

D : min. 50 mm

E : Ambient temperature Measuring point < 35°C

• When embedding the product in a wall, be sure there is some space behind the product for venti-

lation, as shown above, and maintain the ambient temperature at 35°C or lower.

Note

A Samsung Electronics service center can provide details.

3. Floor mount guide

<Side view>

A : min. 50 mm

B: Ambient temperature Measuring point < 20°C

• When embedding the product in the floor, be sure there is a 50 mm space or more behind the product

for ventilation, as shown above, and maintain the ambient temperature at 20°C or lower.

Note

A Samsung Electronics service center can provide details.

Introduction

Mechanical Layout

(400TS-3)

(460TS-3)

Introduction

Installation VESA Bracket

• When installing VESA, make sure to comply with the international VESA standards.

• Purchasing VESA Bracket and Installation Information : Please contact your nearest SAMSUNG

Distributor to place an order. After your order is placed, installation professionals will visit you
and install the bracket.

• At least 2 persons are needed in order to move the LCD Display.

• SAMSUNG is not responsible for any product damage or any injury caused by installation at

customer's discretion.

Dimensions

(400TS-3)

(460TS-3)

Notice

For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length.

Accessories (sold separately)

• Dimension with welcome board

(400TS-3)

Introduction

(460TS-3)

Introduction

• Dimension with other accessories

Wall Bracket Installation

• Contact a technician for installing the wall bracket.

• SAMSUNG Electronics is not responsible for any damages to the product or harm to customers

when the installation is done by the customer.

• This product is for installing on cement walls. The product may not stay in place when installed

on plaster or wood.

Components

Only use the components and accessories shipped with the product.

Introduction

Wall Bracket(1) Hinge(Left 1, Right1)Plastic

To mount the product on the wall bracket

The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and
the screw are the same)

1. Remove the 4 screws on the back of the product.

2. Insert the screw B into the plastic hanger.

Hanger
(4)

Screw
(A)(11)

Screw(B)
(4)

Anchor
(11)

Notice

• Mount the product on the wall bracket and make sure it is properly fixed to the left and right
plastic hangers.

• Be careful when installing the product on the bracket as fingers can be caught in the holes.

• Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place
after installation.

3. Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product.

Introduction

4. Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1).
Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten
the safety pin (3) to securely hold the product to the bracket.

A - LCD Display

B - Wall Bracket

C - Wall

Wall Bracket Angle Adjustment

Adjust the bracket angle to -2° before installing it on the wall.

1. Fix the product to the wall bracket.

2. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the
angle.

Note

You can adjust the bracket angle between -2° and 15°.

Make sure to use the top center, and not the left or the right side of the product to adjust the angle.

Remote Control (RS232C)

Cable connections

interface RS232C(9 pin)

pin TxD(No.2) RxD(No.3) GND(No.5)

Bits rate 9600 bps

Data Bits 8 bit

Parity None

Stop Bits 1 bit

Flow control None

Maximum length 15 m (only shielded type)

Introduction

• Pin assignment

Pin Signal

1 Data Carrier Detect

2 Received Data

3 Transmitted Data

4 Data Terminal Ready

5 Signal Ground

6 Data Set Ready

7 Request to Send

8 Clear to Send

9 Ring Indicator

• RS232C cable

Introduction

Connector : 9-pin D-Sub

Cable : Cross (reversed) cable

-P1- -P1- -P2- -P2-

FEMALE Rx

2

--------->

3

Rx

FEMALE

• Connecting method

Tx

Gnd

3

5

<---------

----------

2

5

Tx

Gnd

Control codes

• Get control

• Set control

• commanding words

No. command type command Value range

1 Power control 0x11 0~1

Header command

ID

0xAA command type 0

Header command

ID

0xAA command

type

DATA Length

DATA

Length

1 Value

CheckSum

DATA

CheckSum

Introduction

2 Volume control 0x12 0~100

3 Input source control 0x14 -

4 Screen Mode control 0x18 -

5 Screen Size control 0x19 0~255

6 PIP on/off control 0x3C 0~1

7 Auto adjustment control 0x3D 0

8 Video wall Mode control 0x5C 0~1

9 Safety Lock 0x5D 0~1

- ID should show hexadecimal value of assigned ID, but ID 0 should be 0xFF.

- Every communication will be made in hexadecimals and Checksum is the sum of all remainings.
If it exceeds two digits,for example, it is 11+FF+01+01=112, discard the number in the first digit
like below.

example)PowerOn&ID=0

Header command

ID

0xAA 0x11 1 Power

Header command

ID

0xAA 0x11 1 1

If you want to control every mechanism connected with Serial Cable regardless of its ID, set ID
part to "0xFE" and send commands. At the time, each product will follow commands but it will
not respond with ACK.

• Power Control

• Function

Personal Computer turns TV / Monitor power ON/OFF.

• Get Power ON/OFF Status

Header command

0xAA 0x11 0

DATA
Length

DATA
Length

ID

DATA 1

CheckSum

DATA 1

12

DATA Length

CheckSum

• Set Power ON/OFF

Header command

ID

0xAA 0x11 1 Power

Power : Power code to be set on TV / Monitor

1 : Power ON

0 : Power OFF

DATA
Length

DATA

CheckSum