Page 1
SyncMaster 963UW / 2063UW
LCD Monitor
User Manual
Page 2
Safety Instructions
Notational
Note
Please read the following safety instructions as they are designed to prevent damage to property and
harm to the user.
Warning / Caution
Failure to follow directions noted by this symbol could result in bodily harm
or damage to the equipment.
Notational Conventions
Power
Prohibited
Do not disassemble
Do not touch
When not used for extended period of time, set your computer to DPM.
If using screen saver, set it to active screen mode.
The images here are for reference only, and are not applicable in all cases (or
countries).
Shortcut to Anti-Afterimage Instructions
Do not use a damaged power cord or plug or a damaged or loose power
outlet.
• Otherwise, this may result in electric shock or fire.
Important to read and understand at all times
Disconnect the plug from the
outlet
Ground to prevent an electric
shock
Do not touch the power plug with wet hands when removing or plug-
ging the plug into the outlet.
• Otherwise, this may result in electric shock.
Make sure to connect the power cord to a grounded power outlet.
• Otherwise, it may result in electric shock or personal injury.
Ensure that the power plug is plugged into the power outlet firmly and
correctly.
• Otherwise, this may result in fire.
1
Page 3
Safety Instructions
Do not forcefully bend or pull the power plug and do not place any
heavy material on it.
• Otherwise, this may result in fire.
Do not connect multiple appliances to the same power outlet.
• Otherwise, this may cause fire due to overheating.
Do not disconnect the power cord while using the product.
• Otherwise, this may result in damage to the product due to electric
shock.
To disconnect the apparatus from the mains, the plug must be pulled
out from the mains socket, therefore the mains plug shall be readily operable.
• This may cause electric shock or fire.
Use only the power cord provided by our company. Do not use the
provided power cord of another product.
Installation
• Otherwise, this may result in fire or electric shock.
Be sure to contact an authorized Service Center when installing your monitor in
a location with heavy dust, high or low temperatures, high humidity, and exposed
to chemical substances and where it operates for 24 hours such as at airports,
train stations etc.
Failure to do so may cause serious damage to your monitor.
Do not drop the monitor when moving it.
• This may cause damage to the product or the person carrying it.
Ensure that at least two persons lift and move the product.
• Otherwise, it may be dropped and cause personal injury, and/or dam-
age the product.
When installing the product in a cabinet or rack, make sure that the
front end of the bottom of the product does not project out.
• Otherwise, it may fall or cause personal injury.
• Use a cabinet or rack of a size appropriate to the product.
DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIGARETTES AND ANY HEATING APPLIANCES NEAR THE PRODUCT.
• Otherwise, this may result in fire.
2
Page 4
Safety Instructions
Keep heating appliances as far away from the power cord or the product as possible.
• Otherwise, this may result in electric shock or fire.
Do not install it in a badly ventilated location such as a bookcase or
closet.
• Otherwise, this may result in fire due to an increase in the internal
temperature.
Put down the monitor carefully.
• Failing to do so may damage the monitor.
Do not place the front of the product on the floor.
• Otherwise, this may result in damage to the screen display.
Ensure that an authorized installation company installs the wall mount.
Clean
• Otherwise, it may fall and cause personal injury.
• Make sure to install the specified wall mount.
Install your product in a well ventilated location. Ensure that there is
a clearance of more than 10 cm from the wall.
• Otherwise, it may result in fire due to an increase in the internal tem-
perature.
Ensure that the packaging vinyl is kept away from children.
• Otherwise, it may result in serious harm (suffocation) if children play
with it.
If the height of your monitor is adjustable, do not place any object or
part of your body on the stand when lowering it.
• This may cause damage to the product or the person carrying it.
When cleaning the monitor case or the surface of the TFT-LCD screen, wipe
with a slightly moistened, soft fabric.
Do not spray cleaner directly onto the surface of the product.
• Otherwise, this may result in the discoloration and distortion of the
structure and the screen surface may peel off.
Clean the product using a soft cloth with a monitor cleaner only. If
you must use a cleaner other than the monitor cleaner, dilute it with water
at a ratio of 1:10.
3
Page 5
Safety Instructions
When cleaning the power plug pins or dusting the power outlet, clean
it with a dry cloth.
• Otherwise, it may result in fire.
When cleaning the product, make sure to disconnect the power cord.
• Otherwise, it may result in electric shock or fire.
When cleaning the product, disconnect the power cord and clean it
softly with a dry cloth.
• (Do not use chemicals such as wax, benzene, alcohol, thinner, mos-
quito repellant, lubricant, or cleaner.) These may change the appearance of the product surface and peel off the indication labels on the
product.
Since the product housing is easily scratched, make sure to use the
specified cloth only.
• Use the specified cloth adding only a little water. As the product may
be scratched if there is any foreign material on the cloth, make sure
to shake it thoroughly before using it.
When cleaning the product, do not spray water directly onto the main
body of the product.
Others
• Ensure that water does not enter the product and that it is not wet.
• Otherwise, this may result in electric shock, fire or a malfunction.
The product is a high voltage product. Ensure that users do not disassemble, repair or modify the product themselves.
• Otherwise, this may result in electric shock or fire. If the product
needs to be repaired, contact a Service Center.
If there is a strange smell or a strange sound or smoke is coming from
the product, disconnect the power plug immediately and contact a Service
Center.
• Otherwise, this may result in electric shock or fire.
Do not place this product in a location exposed to moisture, dust,
smoke, water, or in a car.
• Otherwise, this may result in electric shock or fire.
When you drop the product or the case is broken, turn the power off
and disconnect the power cord. Contact a Service Center.
• Otherwise, this may result in electric shock or fire.
4
Page 6
Safety Instructions
Do not try to move the monitor by pulling only the wire or the signal
cable.
• Otherwise, it may fall and result in electric shock, damage to the
product or fire due to damage to the cable.
Do not lift or move the product back and forwards or right and left
while only holding the power cord or signal cables.
• Otherwise, it may fall and result in electric shock, damage to the
product or fire due to damage to the cable.
Make sure that the ventilating opening is not blocked by a table or
curtain.
• Otherwise, it may result in fire due to an increase in the internal tem-
perature.
Do not place any containers containing water, vases, flowerpots, medicines as well as any metal on the product.
• If water or a foreign material enters the product, disconnect the power
cord and contact a Service Center.
• This may result in a product malfunction, electric shock, or fire.
Do not insert any metal, such as chopsticks, coins, pins and steels, or
inflammable objects, such as matches or paper, inside the product
(through the ventilating openings, input and output terminals, etc).
• If water or foreign material enters the product, disconnect the power
cord and contact a Service Center.
• Otherwise, this may result in electric shock or fire.
When using a fixed screen for a long time, an afterimage or stain may
occur.
• If you are not using your product for a long period of time, put it into
sleep mode or use a moving screen saver.
Set a resolution and frequency appropriate to the product.
• Otherwise, your eyesight may be damaged.
When using headphones or earphones, do not turn the volume too high.
• Having the sound too loud may damage your hearing.
If you continually move closer to the product screen, your eyesight
may be failing.
To ease eye strain, take at least a five-minute break after every hour
of using the monitor.
5
Page 7
Safety Instructions
Do not install it in an unstable location such as an unstable rack or
uneven surface or a location exposed to vibrations.
• Otherwise, it may fall and cause personal injury and/or damage the
product.
• If you use the product in a location exposed to vibrations, it may
damage the product and result in fire.
When moving the product, turn the power off and disconnect the power
plug, antenna cable, and all the cables connected to the product.
• Otherwise, it may result in electric shock or fire.
Ensure that children do not hang onto the product or climb up onto the
product.
• The product may fall and cause personal injury or death.
If you do not use the product for a long period of time, disconnect the
power cord from the power outlet.
• Otherwise, this may result in overheating or fire due to dust, and may
result in fire due to electric shock or leakage.
Do not place any heavy items or toys or confectionery, such as cookies
etc. that may attract the attentions of children onto the product.
• Your children may hang onto the product causing it to fall and this
may result in personal injury or death.
Do not turn the product upside down or move it while holding only
the stand.
• Otherwise, it may fall and result in personal injury and/or damage to
the product.
Do not place the product in a location exposed to direct sunlight or
near any heat such as a fire or heater.
• This may reduce the lifetime of the product, and may result in fire.
Do not drop any objects onto the product or cause any impact to the
product.
• Otherwise, this may result in electric shock or fire.
Do not use a humidifier or kitchen table near the product.
• Otherwise, this may result in electric shock or fire.
When there is a gas leak, do not touch the product or the power plug
but ventilate immediately.
• If a spark occurs, it may cause an explosion or fire.
6
Page 8
Safety Instructions
If the product has been turned on for a long time, the display panel
becomes hot. Do not touch it.
• Keep the small accessories in a location out of the reach of children.
Be careful when adjusting the angle of the product or the height of the
stand.
• This may result in personal injury as your hand or fingers may be-
come caught.
• Also, if you tilt the product too far, it may fall and cause personal
injury.
Do not install the product in a location low enough for children to
reach.
• Otherwise, it may fall and result in personal injury.
• Since the front part of the product is heavy, install the product on a
level and stable surface.
Do not put any heavy objects on the product.
• This may result in personal injury and/or damage to the product.
Good Postures When Using the Monitor
When using the product, use it in the correct position.
• Keep your back straight while looking at the product.
• The distance between your eyes and the screen should
be between 45 to 50 cm. Look at the screen from a
slightly higher location than the height of the screen.
• Tilt the product backwards between 10 to 20 degrees.
Adjust the height of the screen to a slightly lower level
than the level of your eyes.
• Adjust the angle so that light is not reflected on the
screen.
• Place your arms perpendicular to your sides and allow
your arms to be level with the back of the hand.
• Keep your elbow at 90 degrees.
• Keep your knees at greater than 90 degrees, and keep
your heels firmly on the floor. Keep your arms lower
than your heart.
7
Page 9
Introduction
Package Contents
Note
Please make sure the following items are included with your monitor.
If any items are missing, contact your dealer.
Contact a local dealer to buy optional items.
Unpacking
Without stand With stand
Monitor Monitor
Manuals
Quick Setup Guide Warranty Card
(Not available in all loca-
Cables
D-Sub Cable Power Cord USB Cable
Sold separately
User's Guide
tions)
DVI Cable HDMI Cable Headphones
8
Page 10
Others
Note
This is only provided for highly polished black products as a product feature.
Your Monitor
Introduction
Cleaning Cloth
Initial Settings
Select the language using the up or down key.
The displayed content will disappear after 40 seconds.
Turn the Power button off and on. It will be displayed again.
It can be displayed up to three (3) times. Make sure to adjust the resolution of your PC before reaching
the maximum count.
Note
The resolution displayed on the screen is the optimal resolution for this product.
Adjust your PC resolution so that it is the same as the optimal resolution for this product.
9
Page 11
Front
Introduction
MENU button [MENU/ ]
Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu
or return to the previous menu.
Customized Key
You can customize key assignment for the Custom button according to your preferences.
Note
You can configure the Customized key for a required function via Setup > Customized Key.
Volume button
When OSD is not on the screen, push the button to adjust volume.
>> Click here to see an animation clip
Adjust buttons [ ]
Adjust items in the menu.
SOURCE button / Enter button [ ]
Push the 'SOURCE/ ', then selects the video signal while the OSD is off. (When
the SOURCE/
in the upper left of the screen displaying the current mode -- analog or digital input
signal.)
button is pressed to change the input mode, a message appears
/ Activates a highlighted menu item.
10
Page 12
Introduction
Note
If you select the digital mode, you must connect your monitor to the graphic card's
DVI port using the DVI cable.
>> Click here to see an animation clip
AUTO button
Use this button for auto adjustment.
(Available in Analog mode only)
>> Click here to see an animation clip
Power button [ ] / Power indicator
Use this button for turning the monitor on and off.
/ This light glows blue during normal operation, and blinking blue once as the
monitor saves your adjustments.
Camera
Using this camera, you can view and send video for video chatting.
Mic
Rear
Using this microphone, you can view and send audio for video chatting.
Speaker
You can hear sound by connecting the soundcard of your PC to the monitor.
Note
The configuration at the back of the monitor may vary from product to product.
POWER
11
Page 13
DVI IN / RGB IN
Introduction
POWER
Connect the power cord for your monitor to the
POWER port on the back of the monitor.
DVI IN
Connect the DVI cable to the DVI IN port on the
back of your monitor.
RGB IN
USB connection termi-
nal (Option)
Connect the RGB IN terminal at the back of your
monitor to your computer.
UP (USB upstream port)
Connect the UP port of the monitor and the
USB port of the computer with the USB cable.
DOWN (USB downstream port)
Connect the DOWN port of the USB monitor
and a USB device with the USB cable.
Note
To use
to connect the UP (Upstream Cable ) to the
PC.
Make sure to use the USB cable supplied with this
monitor to connect the monitor's UP port
and your computer's USB port.
12
DOWN (Downstream Port), you have
Page 14
Kensington Lock
Introduction
The Kensington Lock is a device used to physically fix the system when using it in a public
place. The locking device has to be purchased
separately. The appearance and locking method
may differ from the illustration depending on the
manufacturer. Refer to the manual provided with
the Kensington Lock for proper use. The locking
device has to be purchased separately.
Note
The location of the Kensington Lock may be different depending on its model.
Using the Anti-Theft Kensington Lock
1. Insert the locking device into the Kensington
slot on the Monitor ( ) and turn it in the
/ MIC
Cable holding ring
locking direction ( ).
2. Connect the Kensington Lock cable.
3. Fix the Kensington Lock to a desk or a heavy
stationary object.
Headphone output terminal
MIC
Connect a microphone to the MIC terminal.
Fix the cables using the holding ring, as shown in
the figure.
13
Page 15
Introduction
Note
See
{963UW}
Connecting Cables for further information regarding cable connections.
14
Page 16
Connections
{963UW}
Connecting Cables
Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
Use a connection appropriate for your computer.
Using the D-sub (Analog) connector on the video card.
• Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.
[RGB IN]
Using the DVI (Digital) connector on the video card.
• Connect the DVI Cable to the DVI IN Port on the back of your Monitor.
[DVI IN]
Connected to a Macintosh.
• Connect the monitor to the Macintosh computer using the D-sub connection cable.
Note
If the monitor and the computer are connected, you can turn them on and use them.
15
Page 17
{963UW}
Connecting USB
Note
You can use a USB device such as a mouse, keyboard, Memory Stick, or external hard disk drive by
connecting them to the DOWN port of the monitor without connecting them to the PC.
The USB port of the monitor supports High-Speed Certified USB 2.0.
Data Rate 480 Mbps 12 Mbps 1.5 Mbps
Power Consumption 2.5 W
Connections
High speed Full speed Low speed
2.5 W
2.5 W
(Max., each port)
1.
Connect the UP port of the monitor and the USB port of the computer with the USB cable.
Note
To use DOWN port, you have to connect the UP (Upstream Cable) to the PC.
Make sure to use the USB cable supplied with this monitor to connect the monitor's
and your computer's USB port.
(Max., each port)
(Max., each port)
UP port
2.
Connect the DOWN port of the USB monitor and a USB device with the USB cable.
3. The use procedures are as the same as those for using an external device connecting to the PC.
• You can connect and use a keyboard and mouse.
• You can play a file from a media device.
(Examples of media devices: MP3, digital camera, etc.)
16
Page 18
Connections
• You can run, move, copy or delete the files on the storage device.
(Examples of storage devices: external memory, memory card, memory reader, HDD-type
MP3 player, etc.)
• You can use other USB devices that can be connected to a computer.
Note
When connecting a device to the DOWN port of the monitor, connect the device using a
cable appropriate to the device.
(For the purchase of the cable and external devices, ask the service center of the corresponding
product.)
The company is not liable for problems or damages to an external device caused by using an
unauthorized cable for the connection.
Some products do not follow the USB standard, and it may cause a malfunction of the device.
If the device malfunctions even if it is connected to the computer, contact the service center of
the device/computer.
{963UW}
Connecting Headphone
Note
You may connect your headphones to the monitor.
1. Connect your headphones to the Headphone connection terminal.
{963UW}
Connecting MIC
Note
You may connect your microphone to the monitor.
17
Page 19
1. Connect the microphone cable to the MIC port on the monitor.
{963UW}
Using the Stand
Connections
Monitor Assembly
Monitor and Bottom
Simple Stand
18
Page 20
Tilt angle
Connections
Using ( ), You can adjust the tilt angle within a range of -3° forward to 24° backward for the most
comfortable viewing angle.
Attaching a Base
This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad.
Monitor
Mounting interface pad (Sold separately)
1. Turn off your monitor and unplug its power cord.
2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.
3. Remove four screws and then remove the stand from the LCD monitor.
4. Align the mounting interface pad with the holes in the rear cover mounting pad and secure it with
four screws that came with the arm-type base, wall mount hanger or other base.
• Do not use screws longer than the standard dimension, as they may damage the
inside of the Monitor.
19
Page 21
Connections
• For wall mounts that do not comply with VESA standard screw specifications,
the length of the screws may differ depending on their specifications.
• Do not use screws that do not comply with the VESA standard screw specifications.
Do not fasten the screws too tightly, as this may damage the product or cause the
product to fall, leading to personal injury.
Samsung is not liable for these kinds of accidents.
• Samsung is not liable for product damage or personal injury when a non-VESA
or non-specified wall mount is used or the consumer fails to follow the product
installation instructions.
• To mount the monitor on a wall, you should purchase the wall mounting kit that
allows you to mount the monitor at least 10 cm away from the wall surface.
• Contact the nearest Samsung Service Center for more information. Samsung
Electronics will not be responsible for damages caused by using a base other than
those specified.
• Please use Wall Mount according to the International standards.
{2063UW}
Connecting Cables
Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
Use a connection appropriate for your computer.
Using the D-sub (Analog) connector on the video card.
• Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.
[RGB IN]
Using the DVI (Digital) connector on the video card.
20
Page 22
• Connect the DVI Cable to the DVI IN Port on the back of your Monitor.
Connected to a Macintosh.
• Connect the monitor to the Macintosh computer using the D-sub connection cable.
Note
If the monitor and the computer are connected, you can turn them on and use them.
{2063UW}
Connecting USB
Note
You can use a USB device such as a mouse, keyboard, Memory Stick, or external hard disk drive by
connecting them to the DOWN port of the monitor without connecting them to the PC.
Connections
[DVI IN]
The USB port of the monitor supports High-Speed Certified USB 2.0.
High speed Full speed Low speed
Data Rate 480 Mbps 12 Mbps 1.5 Mbps
Power Consumption 2.5 W
(Max., each port)
1.
Connect the UP port of the monitor and the USB port of the computer with the USB cable.
Note
To use
DOWN port, you have to connect the UP (Upstream Cable) to the PC.
2.5 W
(Max., each port)
2.5 W
(Max., each port)
Make sure to use the USB cable supplied with this monitor to connect the monitor's UP port
and your computer's USB port.
21
Page 23
Connections
2.
Connect the DOWN port of the USB monitor and a USB device with the USB cable.
3. The use procedures are as the same as those for using an external device connecting to the PC.
• You can connect and use a keyboard and mouse.
• You can play a file from a media device.
(Examples of media devices: MP3, digital camera, etc.)
• You can run, move, copy or delete the files on the storage device.
(Examples of storage devices: external memory, memory card, memory reader, HDD-type
MP3 player, etc.)
• You can use other USB devices that can be connected to a computer.
Note
When connecting a device to the
cable appropriate to the device.
(For the purchase of the cable and external devices, ask the service center of the corresponding
product.)
The company is not liable for problems or damages to an external device caused by using an
unauthorized cable for the connection.
Some products do not follow the USB standard, and it may cause a malfunction of the device.
If the device malfunctions even if it is connected to the computer, contact the service center of
the device/computer.
{2063UW}
Connecting Headphone
Note
DOWN port of the monitor, connect the device using a
You may connect your headphones to the monitor.
22
Page 24
1. Connect your headphones to the Headphone connection terminal.
{2063UW}
Connecting MIC
Note
Connections
You may connect your microphone to the monitor.
1. Connect the microphone cable to the MIC port on the monitor.
23
Page 25
{2063UW}
Using the Stand
Monitor Assembly
Monitor and Bottom
Connections
Simple Stand
Tilt angle
Using ( ), You can adjust the tilt angle within a range of -3° forward to 24° backward for the most
comfortable viewing angle.
Attaching a Base
This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.
24
Page 26
Connections
Monitor
Mounting interface pad (Sold separately)
1. Turn off your monitor and unplug its power cord.
2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.
3. Remove four screws and then remove the stand from the LCD monitor.
4. Align the mounting interface pad with the holes in the rear cover mounting pad and secure it with
four screws that came with the arm-type base, wall mount hanger or other base.
• Do not use screws longer than the standard dimension, as they may damage the
inside of the Monitor.
• For wall mounts that do not comply with VESA standard screw specifications,
the length of the screws may differ depending on their specifications.
• Do not use screws that do not comply with the VESA standard screw specifications.
Do not fasten the screws too tightly, as this may damage the product or cause the
product to fall, leading to personal injury.
Samsung is not liable for these kinds of accidents.
• Samsung is not liable for product damage or personal injury when a non-VESA
or non-specified wall mount is used or the consumer fails to follow the product
installation instructions.
• To mount the monitor on a wall, you should purchase the wall mounting kit that
allows you to mount the monitor at least 10 cm away from the wall surface.
• Contact the nearest Samsung Service Center for more information. Samsung
Electronics will not be responsible for damages caused by using a base other than
those specified.
• Please use Wall Mount according to the International standards.
25
Page 27
Using the Software
{963UW}
Using the WebCam Monitor
This monitor can be used as a normal monitor for video communications and for
viewing multimedia files simply by connecting the power cable and the USB cable
to your PC.
Minimum baseline spec
• System Requirements
CPU : 1.73GHz or Later
OS : Windows XP Service Pack2 or later. However, Windows Vista 64bit is not supported.
RAM : 512 MB RAM or more
USB : 1.1 or higher (USB 2.0 recommended)
Auto Setup for the web camera, microphone and speaker
1. Connect your monitor and PC using a USB cable, as shown in the figure below.
26
Page 28
Using the Software
2. The web camera, microphone and speaker will be set up automatically and appear on the status
bar.
Note
• If the camera is recognized as a USB1.1 device, the screen quality may be degraded and noise
may occur. Make sure to upgrade to USB 2.0.
• Because of the characteristics of USB communication, the device is recognized whenever it
is turned off and on. When the recognition process is finished, you can use it normally.
• If you remove the cable while your PC is recognizing a USB device, it may cause a serious
error to your PC.
• Do not turn the camera too forcefully. This may cause a product malfunction
• Make sure to remove the USB cable after clicking on the <Remove hardware safely> icon on
the taskbar of your PC and unloading the USB device from Windows.
Installation Precautions
1. Never disconnect the USB cable from the USB port while the auto installation is in progress. (The
installation takes about a minute. If you remove the USB port during the installation, a severe
problem may occur with your PC.)
2. Do not turn off the monitor while the auto installation is in progress. (If you turn off the monitor
during the installation, a severe problem may occur with your PC.)
3. The screen may blink when the auto installation is completed. (This occurs when your PC recognizes your monitor as a USB device. This is not a fault.)
4. If the auto installation is completed, configure the position and resolution for the monitors in the
[Settings] tab of the [Display Properties] window. (The optimal resolution for this monitor is 1440
x 900.)
5. If you change the USB Port after your PC has recognized a USB device, it may cause a USB
device recognition error. (You must remove and reinstall the driver.)
27
Page 29
If the installation fails
Note
If the installation is stopped because the New Hardware Wizard has failed, right-click ”My computer“,
and click “Properties” - “System Properties” - the ”Hardware“ tab. Click on the ”Device Manager“
and reinstall the driver by following these steps below.
Using the Software
1.
The symbol showing that the device has failed to be installed is displayed as shown in ( ,
)
2. In this case, click ”Scan for hardware changes” to run the Setup Wizard again. At this time, if the
installation fails, click (
menu.
Checking the configuration
Note
After the installation, you can check the configuration by following these steps:
1. Right-click My computer, click Properties - System Properties - Hardware tab.
, ) and right-click it. Select ”Driver Update” from the displayed
28
Page 30
Using the Software
2. Click on “Device Manager”.
3. A list of installed devices will be displayed, as shown in the figure below.
Checking the Web Camera Setup
1. Double-click My Computer on the Windows Desktop.
2. Double-click the USB Video Device #2. You should find that the web camera has been set up
normally, as shown in the figure below.
Checking the Microphone and Speaker Setup
1. Double-click Sounds and Audio Devices in the Control Panel.
29
Page 31
Using the Software
2. Select the Voice tab and click on Test Hardware.
Note
If the sound from your monitor is too soft, adjust the volume after setting the volume of your PC
to the maximum.
3. Follow the steps described below. You should find that the microphone and speaker have been
set up.
Restrictions on Using the Monitor
1. The Camera and Audio functions of this monitor except the basic Display function are recognized
as USB Devices.
30
Page 32
Using the Software
Note
This monitor must be connected with a D-Sub (Analog) or a DVI-D cable (Digital) when used as
a normal monitor. USB cables are used when connecting other devices.
2. For some media players, when a USB device is being recognized again while a media player is
running, you have to close and run it again to operate the sound and camera devices normally.
3. For some PCs, your PC may not boot up with the monitor recognized even if the USB cable is
connected, depending on the PC BIOS version. Check whether the BIOS on your PC has been
updated to the latest version.
4. Sometimes, if the initial volume setting is low the sound may be very low due to the characteristics
of USB Audio devices. (This may differ according to the operating system.) In this case, adjust
the Master Volume of the PC to an appropriate level.
5. This monitor supports Windows XP Service Pack 2 or later only.
Note
Service Pack 1 or earlier is not supported.
This monitor is designed for optimal performance using Windows XP Service Pack 2 and USB
2.0.
6. The monitor may not operate normally with versions older than USB 2.0.
7. If more than one monitor of this type of model is connected, the USB device recognized for each
monitor may not operate normally.
8. Noise may occur from the MIC and speaker if this monitor is placed too near.
{963UW}
Web Cam Companion 2
Digital video cameras have become common in households today. As a result, a plethora of software has been made available for users to edit and create home movies.
Forgotten in the mix is the widely popular webcam, used for a variety of purposes
ranging from simple video creation to online video chats. To complement webcam's
small but versatile functionalities, ArcSoft Web Cam Companion 2™ offers a broad
range of functions designed and optimized for webcam use. Whether utilized to launch
a video chat client or automatically record movement detected by the device, Web
Cam Companion 2 can do it all!
• System Requirements
Windows XP/ Vista
PIII 800 MHz or equivalent (PIV 2.0 GHz or higher recommended)
100 MB free hard drive space for program installation
256 MB RAM (512 MB DDR RAM recommended)
16-bit color display at 800x600 (32 MB video memory with DirectX 3D support recommended)
DirectX 8.1 or higher (DirectX 9.0c recommended)
Webcam
31
Page 33
Using the Software
1. Insert the Program Setup CD into the CD-ROM drive.
2. Click on Web Cam Companion 2 (WCC2).
3. Select a language and click the "OK" button.
4. Click the "Next" button.
5. Click the "Yes" button.
6. Click the "Next" button.
32
Page 34
7. Click the "Next" button.
Using the Software
8. Click the “Finish” button. The installation of the Web Cam Companion 2 is completed.
Note
For more information on how to use the program, refer to its “Help” section.
Opening the chat program
•
When the installation of the Web Cam Companion 2 program is completed, touch the “
on the monitor for the Web Cam Companion 2 chat window to appear, as shown in the figure
below.
33
” position
Page 35
Using the Software
• Install or select the chat program you want to use.
•
Touch the “ ” position on the monitor. The chat window of the selected program appears immediately.
• To change the chat program to which a shortcut was created, select the Utility in the Start -> All
Programs -> Arcsoft Web Cam Companion 2 .
{963UW}
Magic-I Visual Effects
ArcSoft Magic-i™! Visual Effects is a smart and simple webcam application designed
to enhance users' video chat experience through frames, effects, and themes. Using
"Video Plug-in" technology, Magic-i Visual Effects launches automatically when you
start a video chat with any of your favorite chat clients, so you can apply fun effects
simply and easily. It's also compatible with popular webcam applications like ArcSoft
Web Cam Companion 2™!.
• System Requirements
Windows XP/ Vista
Pentium IV 1.6 GHz or equivalent (Pentium IV 2.4 GHz or higher recommended)
34
Page 36
Using the Software
20 MB free hard drive space required for program installation
256 MB RAM (512 MB DDR RAM recommended)
16-bit color display at 800x600 (32 MB video memory with DirectX 3D support recommended)
DirectX 9.0c or above
1. Insert the Program Setup CD into the CD-ROM drive.
2. Click on Magic-I Visual Effects.
3. Select a language and click the "OK" button.
4. Click the "Next" button.
5. Click the "Yes" button.
35
Page 37
6. Click the "Next" button.
7. Click the "Next" button.
Using the Software
8. Click the “Finish” button. The installation of the Magic-I Visual Effects is completed.
Note
For more information on how to use the program, refer to its “Help” section.
36
Page 38
{963UW}
Media-Impression
ArcSoft Media Impression™ manages your media for you, and gives you tons of fun
and exciting ways to create and share projects featuring your photo, video, and music
files.
• System Requirements
- Windows XP/ Vista
Pentium III 1 GHz or equivalent
512 MB RAM
150 MB available hard disk space
800x600 pixels, 16-bit color monitor
Using the Software
Microsoft Windows Media Player 9.0 or higher
Microsoft DirectX 9.0 or higher
Apple QuickTime® 7.0 or higher recommended
- Macintosh OS X 10.3, 10.4
PowerPC G4 800 MHz, or Intel processor
150 MB available hard disk space
800x600 pixels, 16-bit color monitor
Apple QuickTime®6.0 or higher
1. Insert the Program Setup CD into the CD-ROM drive.
2. Click on Media-Impression.
3. Select a language and click the "OK" button.
4. Click the "Next" button.
37
Page 39
5. Click the "Yes" button.
Using the Software
6. Click the "Next" button.
7. Click the "Next" button.
38
Page 40
Using the Software
8. Select a file type and click the “Next” button.
9. Click the "Finish" button. The installation of the Media-Impression is completed.
For more information on how to use the program, refer to its “Help” section.
{963UW}
Monitor Driver
Note
When prompted by the operating system for the monitor driver, insert the CD-ROM
included with this monitor. Driver installation is slightly different from one operating
system to another. Follow the directions appropriate for the operating system you
have.
Prepare a blank disk and download the driver program file at the Internet web site
shown here.
Internet web site :
http://www.samsung.com/ (Worldwide)
Note
39
Page 41
Using the Software
Installing the Monitor Driver (Automatic)
1. Insert CD into the CD-ROM drive.
2. Click "Windows".
3. Choose your monitor model in the model list, then click the "OK" button.
4. If you can see following message window, then click the "Continue Anyway" button. Then click
"OK" button (Microsoft® Windows® XP/2000 Operating System).
Note
This monitor driver is under certifying MS logo, and this installation doesn't damage your system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
Installing the Monitor Driver (Manual)
Microsoft® Windows Vista™‚ Operating System
1. Insert your Manual CD into your CD-ROM drive.
2.
Click
(Start) and "Control Panel". Then, double-click on "Appearance and Personalization".
40
Page 42
Using the Software
3. Click "Personalization" and then "Display Settings".
4. Click "Advanced Settings...".
5. Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the
configuration for your monitor is completed. The monitor can be used as is.
If the message "Windows needs..." is displayed, as shown in the figure below, click "Continue".
41
Page 43
Using the Software
Note
This monitor driver is under certifying MS logo, and this installation doesn't damage your system.
The certified driver will be posted on Samsung Monitor homepage.
6. Click "Update Driver..." in the "Driver" tab.
7. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a
list of device drivers on my computer".
8. Click "Have Disk...” and select the folder (for example, D:\Drive) where the driver setup file is
located, and click "OK".
9. Select the model that matches your monitor from the list of monitor models on the screen, and
click "Next".
42
Page 44
Using the Software
10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence.
Microsoft® Windows® XP Operating System
1. Insert CD into the CD-ROM drive.
2. Click "Start" → "Control Panel" then click the "Appearance and Themes" icon.
43
Page 45
Using the Software
3. Click "Display" icon and choose the "Settings" tab then click "Advanced...".
4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
5. Click "Update Driver..." and select "Install from a list or..." then click "Next" button.
6. Select "Don't search, I will..." then click "Next" and then click "Have disk".
44
Page 46
Using the Software
7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model
list and click the "Next" button.
8. If you can see following message window, then click the "Continue Anyway" button. Then click
"OK" button.
Note
This monitor driver is under certifying MS logo, and this installation doesn't damage your system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
9. Click the "Close" button then click "OK" button continually.
45
Page 47
Using the Software
10. Monitor driver installation is completed.
Microsoft® Windows® 2000 Operating System
When you can see "Digital Signature Not Found" on your monitor, follow these steps.
1. Choose "OK" button on the "Insert disk" window.
2. Click the "Browse" button on the "File Needed" window.
3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.
How to install
1. Click "Start", "Setting", "Control Panel".
2. Double click the "Display" icon.
3. Select the "Settings" tab and click "Advanced Properties" button.
4. Choose "Monitor".
Case1 : If the "Properties" button is inactive, it means your monitor is properly configured. Please
stop installation
Case2 : If the "Properties" button is active, click the "Properties" button then follow next steps
continually.
5. Click "Driver" and then click on "Update Driver..." then click on the "Next" button.
6. Choose "Display a list of the known drivers for this device so that I can choose a specific driver"
then click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver).
8. Click the "Open" button, then click "OK" button.
9. Choose your monitor model and click the "Next" button then click "Next" button.
10. Click the "Finish" button then the "Close" button.
If you can see the "Digital Signature Not Found" window then click the "Yes" button. And click
the "Finish" button then the "Close" button.
Microsoft® Windows® Millennium Operating System
1. Click "Start", "Setting", "Control Panel".
2. Double click the "Display" icon.
3. Select the "Settings" tab and click "Advanced Properties" button.
46
Page 48
Using the Software
4. Select the "Monitor" tab.
5. Click the "Change" button in the "Monitor Type" area.
6. Choose "Specify the location of the driver".
7. Choose "Display a list of all the driver in a specific location..." then click "Next" button.
8. Click the "Have Disk" button.
9. Specify A:\(D:\driver) then click "OK" button.
10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to
your computer and click "OK".
11. Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box.
Microsoft® Windows® NT Operating System
1. Click "Start", "Settings", "Control Panel", and then double-click "Display" icon.
2. In Display Registration Information window, click Settings Tab and then click "All Display
Modes".
3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and
then click "OK".
4. Click "Apply" button if you see the screen working normally after clicking "Test". If the screen
is not normal, change to a different mode (lower mode of resolution, colors or frequency).
Note
If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by
referring to the Preset Timing Modes in the user guide.
Linux Operating System
To execute X-Window, you need to make the X86Config file, which is a type of system setting file.
1. Press "Enter" at the first and the second screen after executing the X86Config file.
2. The third screen is for setting your mouse.
3. Set a mouse for your computer.
4. The next screen is for selecting a keyboard.
5. Set a Keyboard for your computer.
6. The next screen is for setting your monitor.
7. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.)
8. Set a vertical frequency for your monitor. (You can enter the frequency directly.)
9. Enter the model name of your monitor. This information will not affect the actual execution of
X-Window.
10. You have finished setting up your monitor. Execute X-Window after setting other requested
hardware.
47
Page 49
{963UW}
Natural Color
Natural Color Software Program
Using the Software
One of the recent problems in using a computer is that the color of the images printed out by a printer
or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor.
The Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics & Telecommunications
Research Institute (ETRI). This system is available only for Samsung monitors and makes the color
of the images on the monitor the same as the printed or scanned images. For more information, refer
to Help (F1) in the software program.
How to install the Natural Color software
Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial screen of
the program Natural Color will be executed. Click Natural Color on the initial screen to install the
Natural Color software.
To install the program manually, insert the CD included with the Samsung monitor into the CD-ROM
Drive, click the [Start] button of Windows and then select [Run...]. Enter D:\color\NCProSetup.exe
and then press the [Enter] key. (If the drive where the CD is inserted is not D:\, enter the applicable
drive.)
How to delete the Natural Color software program
Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a program".
Select Natural Color from the list and then click the "Add/Delete" button.
48
Page 50
{963UW}
MagicTune™
Installation
1. Insert the installation CD into the CD-ROM drive.
2. Click the MagicTune™ installation file.
Using the Software
Note
If the popup window to install the software for the main screen is not displayed, proceed with the
installation using the MagicTune executable file on the CD.
3. Select installation Language, Click "Next".
4. When the Installation Shield Wizard window appears, click "Next".
5. Select "I agree to the terms of the license agreement" to accept the terms of use.
6. Choose a folder to install the MagicTune™ program.
7. Click "Install".
8. The "Installation Status" window appears.
9. Click "Finish".
10. When the installation is complete, the MagicTune™ executable icon appears on your desktop.
Double-click the icon to start the program.
MagicTune™ execution icon may not appear depending on specification of computer system or monitor. If that happens, press F5 Key.
Installation Problems
The installation of MagicTune™ can be affected by such factors as the video card, motherboard and
the network environment.
System Requirements
OS
• Windows 2000
• Windows XP Home Edition
• Windows XP Professional
• Windows Vista™
49
Page 51
Uninstall
Using the Software
It is recommended using MagicTune™ in Windows® 2000 or later.
Hardware
• 32 MB Memory above
• 60 MB Hard disk space above
For more information, visit the MagicTune™ website.
The MagicTune™ program can be removed only by using the "Add or Remove Programs" option of
the Windows® Control Panel.
Perform the following steps remove MagicTune™.
1. Go to [Task Tray] → [Start] → [Settings] and select [Control Panel] in the menu. If the program
runs on Windows® XP, go to [Control Panel] in the [Start] menu.
2. Click the "Add or Remove Programs" icon in Control Panel.
3. In the "Add or Remove Programs" screen, scroll down to find "MagicTune™." Click on it to
highlight it.
4. Click the "Change/Remove" button to remove the program.
5. Click "Yes" to begin the uninstall process.
6. Wait until the "Uninstall Complete" dialog box appears.
Note
Visit the MagicTune™ website for technical support for MagicTune™, FAQs (questions and answers)
and software upgrades.
{2063UW}
Using the WebCam Monitor
This monitor can be used as a normal monitor for video communications and for
viewing multimedia files simply by connecting the power cable and the USB cable
to your PC.
50
Page 52
Using the Software
Minimum baseline spec
• System Requirements
CPU : 1.73GHz or Later
OS : Windows XP Service Pack2 or later. However, Windows Vista 64bit is not supported.
RAM : 512 MB RAM or more
USB : 1.1 or higher (USB 2.0 recommended)
Auto Setup for the web camera, microphone and speaker
1. Connect your monitor and PC using a USB cable, as shown in the figure below.
2. The web camera, microphone and speaker will be set up automatically and appear on the status
bar.
51
Page 53
Note
• If the camera is recognized as a USB1.1 device, the screen quality may be degraded and noise
may occur. Make sure to upgrade to USB 2.0.
• Because of the characteristics of USB communication, the device is recognized whenever it
is turned off and on. When the recognition process is finished, you can use it normally.
• If you remove the cable while your PC is recognizing a USB device, it may cause a serious
error to your PC.
• Do not turn the camera too forcefully. This may cause a product malfunction
• Make sure to remove the USB cable after clicking on the <Remove hardware safely> icon on
the taskbar of your PC and unloading the USB device from Windows.
Installation Precautions
Using the Software
1. Never disconnect the USB cable from the USB port while the auto installation is in progress. (The
installation takes about a minute. If you remove the USB port during the installation, a severe
problem may occur with your PC.)
2. Do not turn off the monitor while the auto installation is in progress. (If you turn off the monitor
during the installation, a severe problem may occur with your PC.)
3. The screen may blink when the auto installation is completed. (This occurs when your PC recognizes your monitor as a USB device. This is not a fault.)
4. If the auto installation is completed, configure the position and resolution for the monitors in the
[Settings] tab of the [Display Properties] window. (The optimal resolution for this monitor is 1680
x 1050.)
5. If you change the USB Port after your PC has recognized a USB device, it may cause a USB
device recognition error. (You must remove and reinstall the driver.)
If the installation fails
Note
If the installation is stopped because the New Hardware Wizard has failed, right-click ”My computer“,
and click “Properties” - “System Properties” - the ”Hardware“ tab. Click on the ”Device Manager“
and reinstall the driver by following these steps below.
52
Page 54
Using the Software
1.
The symbol showing that the device has failed to be installed is displayed as shown in ( ,
)
2. In this case, click ”Scan for hardware changes” to run the Setup Wizard again. At this time, if the
installation fails, click (
menu.
Checking the configuration
Note
After the installation, you can check the configuration by following these steps:
1. Right-click My computer, click Properties - System Properties - Hardware tab.
, ) and right-click it. Select ”Driver Update” from the displayed
2. Click on “Device Manager”.
3. A list of installed devices will be displayed, as shown in the figure below.
53
Page 55
Checking the Web Camera Setup
1. Double-click My Computer on the Windows Desktop.
2. Double-click the USB Video Device #2. You should find that the web camera has been set up
normally, as shown in the figure below.
Using the Software
Checking the Microphone and Speaker Setup
1. Double-click Sounds and Audio Devices in the Control Panel.
2. Select the Voice tab and click on Test Hardware.
54
Page 56
Using the Software
Note
If the sound from your monitor is too soft, adjust the volume after setting the volume of your PC
to the maximum.
3. Follow the steps described below. You should find that the microphone and speaker have been
set up.
Restrictions on Using the Monitor
1. The Camera and Audio functions of this monitor except the basic Display function are recognized
as USB Devices.
Note
This monitor must be connected with a D-Sub (Analog) or a DVI-D cable (Digital) when used as
a normal monitor. USB cables are used when connecting other devices.
2. For some media players, when a USB device is being recognized again while a media player is
running, you have to close and run it again to operate the sound and camera devices normally.
3. For some PCs, your PC may not boot up with the monitor recognized even if the USB cable is
connected, depending on the PC BIOS version. Check whether the BIOS on your PC has been
updated to the latest version.
4. Sometimes, if the initial volume setting is low the sound may be very low due to the characteristics
of USB Audio devices. (This may differ according to the operating system.) In this case, adjust
the Master Volume of the PC to an appropriate level.
55
Page 57
5. This monitor supports Windows XP Service Pack 2 or later only.
Note
Service Pack 1 or earlier is not supported.
This monitor is designed for optimal performance using Windows XP Service Pack 2 and USB
2.0.
6. The monitor may not operate normally with versions older than USB 2.0.
7. If more than one monitor of this type of model is connected, the USB device recognized for each
monitor may not operate normally.
8. Noise may occur from the MIC and speaker if this monitor is placed too near.
{2063UW}
Web Cam Companion 2
Digital video cameras have become common in households today. As a result, a plethora of software has been made available for users to edit and create home movies.
Forgotten in the mix is the widely popular webcam, used for a variety of purposes
ranging from simple video creation to online video chats. To complement webcam's
small but versatile functionalities, ArcSoft Web Cam Companion 2™ offers a broad
range of functions designed and optimized for webcam use. Whether utilized to launch
a video chat client or automatically record movement detected by the device, Web
Cam Companion 2 can do it all!
Using the Software
• System Requirements
Windows XP/ Vista
PIII 800 MHz or equivalent (PIV 2.0 GHz or higher recommended)
100 MB free hard drive space for program installation
256 MB RAM (512 MB DDR RAM recommended)
16-bit color display at 800x600 (32 MB video memory with DirectX 3D support recommended)
DirectX 8.1 or higher (DirectX 9.0c recommended)
Webcam
1. Insert the Program Setup CD into the CD-ROM drive.
2. Click on Web Cam Companion 2 (WCC2).
3. Select a language and click the "OK" button.
4. Click the "Next" button.
56
Page 58
5. Click the "Yes" button.
Using the Software
6. Click the "Next" button.
7. Click the "Next" button.
57
Page 59
Using the Software
8. Click the “Finish” button. The installation of the Web Cam Companion 2 is completed.
Note
For more information on how to use the program, refer to its “Help” section.
Opening the chat program
•
When the installation of the Web Cam Companion 2 program is completed, touch the “
on the monitor for the Web Cam Companion 2 chat window to appear, as shown in the figure
below.
• Install or select the chat program you want to use.
” position
•
Touch the “
mediately.
• To change the chat program to which a shortcut was created, select the Utility in the Start -> All
Programs -> Arcsoft Web Cam Companion 2 .
” position on the monitor. The chat window of the selected program appears im-
58
Page 60
{2063UW}
Magic-I Visual Effects
ArcSoft Magic-i™! Visual Effects is a smart and simple webcam application designed
to enhance users' video chat experience through frames, effects, and themes. Using
"Video Plug-in" technology, Magic-i Visual Effects launches automatically when you
start a video chat with any of your favorite chat clients, so you can apply fun effects
simply and easily. It's also compatible with popular webcam applications like ArcSoft
Web Cam Companion 2™!.
Using the Software
• System Requirements
Windows XP/ Vista
Pentium IV 1.6 GHz or equivalent (Pentium IV 2.4 GHz or higher recommended)
20 MB free hard drive space required for program installation
256 MB RAM (512 MB DDR RAM recommended)
16-bit color display at 800x600 (32 MB video memory with DirectX 3D support recommended)
DirectX 9.0c or above
1. Insert the Program Setup CD into the CD-ROM drive.
2. Click on Magic-I Visual Effects.
3. Select a language and click the "OK" button.
4. Click the "Next" button.
59
Page 61
5. Click the "Yes" button.
Using the Software
6. Click the "Next" button.
7. Click the "Next" button.
60
Page 62
Using the Software
8. Click the “Finish” button. The installation of the Magic-I Visual Effects is completed.
Note
For more information on how to use the program, refer to its “Help” section.
{2063UW}
Media-Impression
ArcSoft Media Impression™ manages your media for you, and gives you tons of fun
and exciting ways to create and share projects featuring your photo, video, and music
files.
• System Requirements
- Windows XP/ Vista
Pentium III 1 GHz or equivalent
512 MB RAM
150 MB available hard disk space
800x600 pixels, 16-bit color monitor
Microsoft Windows Media Player 9.0 or higher
Microsoft DirectX 9.0 or higher
Apple QuickTime® 7.0 or higher recommended
- Macintosh OS X 10.3, 10.4
PowerPC G4 800 MHz, or Intel processor
150 MB available hard disk space
800x600 pixels, 16-bit color monitor
Apple QuickTime®6.0 or higher
1. Insert the Program Setup CD into the CD-ROM drive.
61
Page 63
Using the Software
2. Click on Media-Impression.
3. Select a language and click the "OK" button.
4. Click the "Next" button.
5. Click the "Yes" button.
6. Click the "Next" button.
62
Page 64
Using the Software
7. Click the "Next" button.
8. Select a file type and click the “Next” button.
9. Click the "Finish" button. The installation of the Media-Impression is completed.
Note
For more information on how to use the program, refer to its “Help” section.
63
Page 65
Using the Software
{2063UW}
Monitor Driver
Note
When prompted by the operating system for the monitor driver, insert the CD-ROM
included with this monitor. Driver installation is slightly different from one operating
system to another. Follow the directions appropriate for the operating system you
have.
Prepare a blank disk and download the driver program file at the Internet web site
shown here.
Internet web site :
http://www.samsung.com/ (Worldwide)
Installing the Monitor Driver (Automatic)
1. Insert CD into the CD-ROM drive.
2. Click "Windows".
3. Choose your monitor model in the model list, then click the "OK" button.
4. If you can see following message window, then click the "Continue Anyway" button. Then click
"OK" button (Microsoft® Windows® XP/2000 Operating System).
64
Page 66
Using the Software
Note
This monitor driver is under certifying MS logo, and this installation doesn't damage your system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
Installing the Monitor Driver (Manual)
Microsoft® Windows Vista™‚ Operating System
1. Insert your Manual CD into your CD-ROM drive.
2.
Click
(Start) and "Control Panel". Then, double-click on "Appearance and Personalization".
3. Click "Personalization" and then "Display Settings".
4. Click "Advanced Settings...".
5. Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the
configuration for your monitor is completed. The monitor can be used as is.
If the message "Windows needs..." is displayed, as shown in the figure below, click "Continue".
65
Page 67
Using the Software
Note
This monitor driver is under certifying MS logo, and this installation doesn't damage your system.
The certified driver will be posted on Samsung Monitor homepage.
6. Click "Update Driver..." in the "Driver" tab.
7. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a
list of device drivers on my computer".
8. Click "Have Disk...” and select the folder (for example, D:\Drive) where the driver setup file is
located, and click "OK".
66
Page 68
Using the Software
9. Select the model that matches your monitor from the list of monitor models on the screen, and
click "Next".
10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence.
Microsoft® Windows® XP Operating System
67
Page 69
Using the Software
1. Insert CD into the CD-ROM drive.
2. Click "Start" → "Control Panel" then click the "Appearance and Themes" icon.
3. Click "Display" icon and choose the "Settings" tab then click "Advanced...".
4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
5. Click "Update Driver..." and select "Install from a list or..." then click "Next" button.
6. Select "Don't search, I will..." then click "Next" and then click "Have disk".
68
Page 70
Using the Software
7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model
list and click the "Next" button.
8. If you can see following message window, then click the "Continue Anyway" button. Then click
"OK" button.
Note
This monitor driver is under certifying MS logo, and this installation doesn't damage your system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
9. Click the "Close" button then click "OK" button continually.
69
Page 71
Using the Software
10. Monitor driver installation is completed.
Microsoft® Windows® 2000 Operating System
When you can see "Digital Signature Not Found" on your monitor, follow these steps.
1. Choose "OK" button on the "Insert disk" window.
2. Click the "Browse" button on the "File Needed" window.
3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.
How to install
1. Click "Start", "Setting", "Control Panel".
2. Double click the "Display" icon.
3. Select the "Settings" tab and click "Advanced Properties" button.
4. Choose "Monitor".
Case1 : If the "Properties" button is inactive, it means your monitor is properly configured. Please
stop installation
Case2 : If the "Properties" button is active, click the "Properties" button then follow next steps
continually.
5. Click "Driver" and then click on "Update Driver..." then click on the "Next" button.
6. Choose "Display a list of the known drivers for this device so that I can choose a specific driver"
then click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver).
8. Click the "Open" button, then click "OK" button.
9. Choose your monitor model and click the "Next" button then click "Next" button.
10. Click the "Finish" button then the "Close" button.
If you can see the "Digital Signature Not Found" window then click the "Yes" button. And click
the "Finish" button then the "Close" button.
Microsoft® Windows® Millennium Operating System
1. Click "Start", "Setting", "Control Panel".
2. Double click the "Display" icon.
3. Select the "Settings" tab and click "Advanced Properties" button.
70
Page 72
Using the Software
4. Select the "Monitor" tab.
5. Click the "Change" button in the "Monitor Type" area.
6. Choose "Specify the location of the driver".
7. Choose "Display a list of all the driver in a specific location..." then click "Next" button.
8. Click the "Have Disk" button.
9. Specify A:\(D:\driver) then click "OK" button.
10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to
your computer and click "OK".
11. Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box.
Microsoft® Windows® NT Operating System
1. Click "Start", "Settings", "Control Panel", and then double-click "Display" icon.
2. In Display Registration Information window, click Settings Tab and then click "All Display
Modes".
3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and
then click "OK".
4. Click "Apply" button if you see the screen working normally after clicking "Test". If the screen
is not normal, change to a different mode (lower mode of resolution, colors or frequency).
Note
If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by
referring to the Preset Timing Modes in the user guide.
Linux Operating System
To execute X-Window, you need to make the X86Config file, which is a type of system setting file.
1. Press "Enter" at the first and the second screen after executing the X86Config file.
2. The third screen is for setting your mouse.
3. Set a mouse for your computer.
4. The next screen is for selecting a keyboard.
5. Set a Keyboard for your computer.
6. The next screen is for setting your monitor.
7. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.)
8. Set a vertical frequency for your monitor. (You can enter the frequency directly.)
9. Enter the model name of your monitor. This information will not affect the actual execution of
X-Window.
10. You have finished setting up your monitor. Execute X-Window after setting other requested
hardware.
71
Page 73
{2063UW}
Natural Color
Natural Color Software Program
Using the Software
One of the recent problems in using a computer is that the color of the images printed out by a printer
or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor.
The Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics & Telecommunications
Research Institute (ETRI). This system is available only for Samsung monitors and makes the color
of the images on the monitor the same as the printed or scanned images. For more information, refer
to Help (F1) in the software program.
How to install the Natural Color software
Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial screen of
the program Natural Color will be executed. Click Natural Color on the initial screen to install the
Natural Color software.
To install the program manually, insert the CD included with the Samsung monitor into the CD-ROM
Drive, click the [Start] button of Windows and then select [Run...]. Enter D:\color\NCProSetup.exe
and then press the [Enter] key. (If the drive where the CD is inserted is not D:\, enter the applicable
drive.)
How to delete the Natural Color software program
Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a program".
Select Natural Color from the list and then click the "Add/Delete" button.
72
Page 74
{2063UW}
MagicTune™
Installation
1. Insert the installation CD into the CD-ROM drive.
2. Click the MagicTune™ installation file.
Using the Software
Note
If the popup window to install the software for the main screen is not displayed, proceed with the
installation using the MagicTune executable file on the CD.
3. Select installation Language, Click "Next".
4. When the Installation Shield Wizard window appears, click "Next".
5. Select "I agree to the terms of the license agreement" to accept the terms of use.
6. Choose a folder to install the MagicTune™ program.
7. Click "Install".
8. The "Installation Status" window appears.
9. Click "Finish".
10. When the installation is complete, the MagicTune™ executable icon appears on your desktop.
Double-click the icon to start the program.
MagicTune™ execution icon may not appear depending on specification of computer system or monitor. If that happens, press F5 Key.
Installation Problems
The installation of MagicTune™ can be affected by such factors as the video card, motherboard and
the network environment.
System Requirements
OS
• Windows 2000
• Windows XP Home Edition
• Windows XP Professional
• Windows Vista™
73
Page 75
Uninstall
Using the Software
It is recommended using MagicTune™ in Windows® 2000 or later.
Hardware
• 32 MB Memory above
• 60 MB Hard disk space above
For more information, visit the MagicTune™ website.
The MagicTune™ program can be removed only by using the "Add or Remove Programs" option of
the Windows® Control Panel.
Perform the following steps remove MagicTune™.
1. Go to [Task Tray] → [Start] → [Settings] and select [Control Panel] in the menu. If the program
runs on Windows® XP, go to [Control Panel] in the [Start] menu.
2. Click the "Add or Remove Programs" icon in Control Panel.
3. In the "Add or Remove Programs" screen, scroll down to find "MagicTune™." Click on it to
highlight it.
4. Click the "Change/Remove" button to remove the program.
5. Click "Yes" to begin the uninstall process.
6. Wait until the "Uninstall Complete" dialog box appears.
Note
Visit the MagicTune™ website for technical support for MagicTune™, FAQs (questions and answers)
and software upgrades.
74
Page 76
Adjusting the Monitor
{963UW}
Direct Functions
AUTO
When the 'AUTO' button is pressed, the auto adjustment screen appears as shown in the animated
screen on the center.
Auto adjustment allows the monitor to self-adjust to the incoming Analog signal. The values of Fine,
Coarse and Position are adjusted automatically.
(Available in Analog mode only)
If auto adjustment does not work properly, press 'AUTO' button again to adjust picture with more
accuracy.
If you change resolution in the control panel, auto function will be executed automatically.
OSD Lock & Unlock
When pressing the AUTO button after locking the OSD
75
Page 77
Adjusting the Monitor
When pressing the MENU button after locking the OSD
This is the function that locks the OSD in order to keep the current states of settings or prevent others
from adjusting the current settings.
Lock : Hold down the MENU button for more than five (5) seconds to activate the OSD adjustment
lock function.
Unlock : Hold down the MENU button for more than five (5) seconds to deactivate the OSD adjustment
lock function.
76
Page 78
Note
Though the OSD adjustment lock function is activated, you can still adjust the brightness and contrast,
and adjust Customized Key ( ) using the Direct button.
Customized key
Adjusting the Monitor
You can customize key assignment for the Custom button according to your preferences.
To view the operating screen displayed when pressing the [ ] button after configuring the customized key for a function, click the name of each function.
(MagicBright - MagicColor - Color Effect - Image Size )
Note
You can configure the customized key for a required function via Setup > Customized Key.
77
Page 79
Volume
Adjusting the Monitor
SOURCE
When OSD is not on the screen, push the button to adjust volume.
Selects the video signal while the OSD is off.
78
Page 80
{963UW}
OSD Function
Adjusting the Monitor
Picture Brightness Contrast MagicBright
Picture
Brightness
(Not available in MagicBright mode of Dynamic Contrast.)
Color MagicColor Color Tone Color Con-
trol
Image Coarse Fine Sharpness H-Position V-Position
OSD Language H-Position V-Position Transparen-cyDisplay Time
Setup Reset Customized
Key
Information
Off Timer Auto Source Image Size
Color Effect Gamma
Contrast
You can use the on-screen menus to change the brightness according to personal preference.
MENU →
(Not available in MagicBright mode of Dynamic Contrast.)
→ → , → MENU
79
Page 81
Adjusting the Monitor
You can use the on-screen menus to change the contrast according to personal preference.
( Not available in MagicColor mode of Full and Intelligent. )
MENU → → , → → , → MENU
MagicBright
Push the button to circle through available preconfigured modes.
MagicBright is a new feature providing optimum viewing environment depending on the contents of
the image you are watching. Currently seven different modes are available: Custom, Text, Internet,
80
Page 82
Adjusting the Monitor
Game, Sport, Movie and Dynamic Contrast. Each mode has its own pre-configured brightness value.
You can easily select one of seven settings by simply pressing Customized Key control button.
• Custom
Although the values are carefully chosen by our engineers, the pre-configured values may not be
comfortable to your eyes depending on your taste.
If this is the case, adjust the brightness and contrast by using the OSD menu.
• Text
For documentations or works involving heavy text.
• Internet
For working with a mixture of images such as texts and graphics.
• Game
For watching motion pictures such as a game.
• Sport
For watching motion pictures such as a sport.
• Movie
For watching motion pictures such as a DVD or Video CD.
• Dynamic Contrast
Dynamic Contrast is to automatically detect distribution of inputted visual signal and adjust to
create optimum contrast.
MENU → → , → → , → MENU
Color
(Not available in MagicBright mode of Dynamic Contrast.)
81
Page 83
MagicColor
Adjusting the Monitor
MagicColor is a new technology that Samsung has exclusively developed to improve digital image
and to display natural color more clearly without disturbing image quality.
• Off - Returns to the original mode.
• Demo - The screen before applying MagicColor appears on the right and the screen after applying
MagicColor appears on the left.
• Full - Displays not only vivid natural color but also more realistic natural skin color with clearness.
• Intelligent - Displays vivid natural color with clearness.
MENU → , → → → , → MENU
82
Page 84
Color Tone
Adjusting the Monitor
The tone of the color can be changed and one of four modes can be selected.
• Cool - Makes whites bluish.
• Normal - Keeps whites white.
• Warm - Makes whites reddish.
• Custom - Select this mode when you want to adjust the image according to your preferences.
( Not available in MagicColor mode of Full and Intelligent. )
MENU → , → → , → → , → MENU
83
Page 85
Color Control
Adjusting the Monitor
Adjusts individual Red, Green, Blue color balance.
( Not available in MagicColor mode of Full and Intelligent. )
MENU → , → → , → → , → → , → MENU
Color Effect
You can change the overall mood by changing the screen colors.
( Not available in MagicColor mode of Full and Intelligent. )
84
Page 86
Gamma
Adjusting the Monitor
• Off - This applies an achromatic color to the screen to adjust the screen effects.
• Grayscale - The default colors of black and white are displayed.
• Green - This applies the green color effect to a black and white screen.
• Aqua - This applies the aqua color effect to a black and white screen.
• Sepia - This applies the Sepia color effect to a black and white screen.
MENU → , → → , → → , → MENU
Gamma correction changes the luminance of the colors with intermediate luminance.
• Mode 1 • Mode 2 • Mode 3
MENU → , → → , → → , → MENU
85
Page 87
Image
Coarse
Adjusting the Monitor
Removes noise such as vertical stripes.
Coarse adjustment may move the screen image area. You may relocate it to the center using the
horizontal control menu.
(Available in Analog mode only)
MENU → , → → → , → MENU
86
Page 88
Fine
Adjusting the Monitor
Removes noise such as horizontal stripes.
If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed).
(Available in Analog mode only)
MENU →
Sharpness
, → → , → → , → MENU
Changes the clearance of image.
87
Page 89
Adjusting the Monitor
( Not available in MagicColor mode of Full and Intelligent. )
MENU →
H-Position
, → → , → → , → MENU
Changes the horizontal position of the monitor's entire display.
(Available in Analog mode only)
MENU → , → → , → → , → MENU
V-Position
88
Page 90
Changes the vertical position of the monitor's entire display.
(Available in Analog mode only)
MENU → , → → , → → , → MENU
OSD
Language
Adjusting the Monitor
You can choose one of nine languages.
Note
The language chosen affects only the language of the OSD. It has no effect on any software running
on the computer.
MENU → , → → → , → MENU
89
Page 91
H-Position
Adjusting the Monitor
You can change the horizontal position where the OSD menu appears on your monitor.
MENU → , → → , → → , → MENU
V-Position
You can change the vertical position where the OSD menu appears on your monitor.
MENU →
, → → , → → , → MENU
90
Page 92
Transparency
Adjusting the Monitor
Change the transparency of the background of the OSD.
• Off • On
MENU → , → → , → → , → MENU
Display Time
The menu will be automatically turned off if no adjustments are made for a certain time period.
You can set the amount of time the menu will wait before it is turned off.
91
Page 93
Setup
Reset
Adjusting the Monitor
• 5 sec • 10 sec • 20 sec • 200 sec
MENU → , → → , → → , → MENU
Reverts the product settings to factory defaults.
• No • Yes
MENU → , → → , → → MENU
92
Page 94
Customized Key
Adjusting the Monitor
Off Timer
You can specify a function which will be activated when the Customized Key ( )is pressed.
MENU → , → → , → → , →MENU
The monitors will turn off automatically at the specified time.
• Off • On
93
Page 95
MENU → , → → , → → , → → , → MENU
Auto Source
Adjusting the Monitor
Select Auto Source for the monitor to automatically select the signal source.
• Auto • Manual
MENU → , → → → , → MENU
Image Size
You can change the size of the screen displayed on your monitor.
94
Page 96
Adjusting the Monitor
• Auto - The screen is displayed in accordance with the screen aspect ratio of the input signals.
• Wide - A full screen is displayed regardless of the screen aspect ratio of the input signals.
Note
• Signals not available in the standard mode table are not supported.
• If the wide screen which is the optimal resolution for the monitor is set on your PC, this function
is not performed.
MENU → , → → , → → , → MENU
Information
Shows a video source, display mode on the OSD screen.
MENU → , →MENU
95
Page 97
{2063UW}
Direct Functions
AUTO
Adjusting the Monitor
When the 'AUTO' button is pressed, the auto adjustment screen appears as shown in the animated
screen on the center.
Auto adjustment allows the monitor to self-adjust to the incoming Analog signal. The values of Fine,
Coarse and Position are adjusted automatically.
(Available in Analog mode only)
If auto adjustment does not work properly, press 'AUTO' button again to adjust picture with more
accuracy.
If you change resolution in the control panel, auto function will be executed automatically.
OSD Lock & Unlock
When pressing the AUTO button after locking the OSD
96
Page 98
Adjusting the Monitor
When pressing the MENU button after locking the OSD
This is the function that locks the OSD in order to keep the current states of settings or prevent others
from adjusting the current settings.
Lock : Hold down the MENU button for more than five (5) seconds to activate the OSD adjustment
lock function.
Unlock : Hold down the MENU button for more than five (5) seconds to deactivate the OSD adjustment
lock function.
97
Page 99
Note
Though the OSD adjustment lock function is activated, you can still adjust the brightness and contrast,
and adjust Customized Key ( ) using the Direct button.
Customized key
Adjusting the Monitor
You can customize key assignment for the Custom button according to your preferences.
To view the operating screen displayed when pressing the [ ] button after configuring the customized key for a function, click the name of each function.
(MagicBright - MagicColor - Color Effect - Image Size )
Note
You can configure the customized key for a required function via Setup > Customized Key.
98
Page 100
Volume
Adjusting the Monitor
SOURCE
When OSD is not on the screen, push the button to adjust volume.
Selects the video signal while the OSD is off.
99
Loading...