Samsung 1701MP, 1501MP User Manual

SyncMaster 1501MP / 1701MP

Index

Main Page

Safety Instructions

Introduction

Setup

Notational

Power

Installation

Cleaning

Other

Unpacking

Front

Rear

Remote Control

Connecting Your Monitor

Connecting to a Computer

Connecting to Other Devices

Installing the Monitor Driver

Automatic

Manual

Installing a VESA Base

Using the FOLD button

Installing a VESA Base

Adjusting Your LCD Monitor

User Controls

User control buttons

Direct-Access Features

On-Screen Display

OSD Functions

Screen Adjustment Animation Clips

Troubleshooting

Check before Calling for Service

Problems and Solutions

Q & A

Specifications

General Specifications

PowerSaver

Preset Timing Modes

Information

Service Center

Terms

Regulatory

Natural Color

For Better Display

Authority

Safety Instructions : Notational

Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.

Prohibited Important to read and understand at all times

Do not disassemble Disconnect the plug from the outlet

Do not touch Grounding to prevent an electric shock

Safety Instructions : Power

When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode.

Do not use a damaged or loose plug.

z This may cause an electric shock or fire.

Do not pull the plug out by the wire nor touch the plug with wet hands.

This may cause an electric shock or fire.

Use only a properly grounded plug and receptacle.

z An improper ground may cause electric shock or equipment damage.

Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage.

z This may cause an electric shock or fire.

Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time.

z Failure to do so may cause an electric shock or fire.

Do not connect too many extension cords or plugs to an outlet.

This may cause a fire.

Safety Instructions : Installation

Do not cover the vents on the monitor cabinet.

z Bad ventilation may cause a breakdown or fire.

Put your monitor in a location with low humidity and a minimum of dust.

z An electric shock or fire could result inside the monitor.

Do not drop the monitor when moving it.

This may cause damage to the product or human body.

Place the monitor on a flat and stable surface.

z The monitor can cause injury by falling.

Set down the monitor carefully.

z It could be damaged or broken.

Do not place the monitor face down.

z The TFT-LCD surface may be damaged.

Safety Instructions : Cleaning

When cleaning the monitor case or the surface of the TFT-LCD, wipe with a slightly moistened, soft fabric.

Do not spray detergent directly on the monitor.

Use the recommended detergent with a smooth cloth.

If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth.

z A dirty connector can cause an electric shock or fire.

Do not set a glass of water, chemicals or any small metal objects on the monitor.

z This may cause damage, electric shock or a fire. z If a foreign substance gets into the monitor, disconnect the plug and then

contact a service center.

Safety Instructions : Ohter

Do not remove cover(or back). No user serviceable parts inside.

z This may cause an electric shock or a fire. z Refer servicing to qualified service personnel.

If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and

contact an authorized dealer or service.

z This may cause an electric shock or fire.

Do not place any heavy objects on the monitor.

This may cause an electric shock or a fire.

For each hour of looking at the monitor, you should let your eyes rest for 5 minutes.

z This will reduce eye fatigue.

Do not use or store inflammable substances near the monitor.

z This may cause an explosion or fire.

Do not try to move the monitor by pulling on the wire or the signal cable.

z This may cause a breakdown, electric shock or a fire due to damage to

the cable.

Do not move the monitor right or left by pulling only the wire or the signal cable.

This may cause a breakdown, electric shock or a fire due to damage to the cable.

Never insert anything metallic into the monitor openings.

z This may cause an electric shock, fire or injury.

Safety Instructions : Ohter

Keep all power adaptors apart.

z Possible fire hazard.

Keep power adaptor away from any other heat source.

Possible fire hazard.

Remove and discard vinyl bag from power adaptor before use.

z Possible fire hazard.

Always keep power adaptor in well-ventilated area.

If you view a fixed screen for an extended period of time, residual image or blurriness may appear.

z Change the mode to energy save or set a screensaver to moving picture

when you need to be away from the monitor for an extended period of time.

Introduction : Unpacking

Please make sure the following items are included with your monitor. If any items are missing, contact

your dealer.

User's Guide and Natural

Color/Driver Installation CD

Remote Control /

Batteries (CR2025) Audio Cable

Quick Setup Guide

Power Cord Signal Cable(15 pin D-Sub)

DC Adapter

Monitor

Warranty Card

(Not available in all locations)

Introduction : Front

For detailed information concerning the monitor functions, refer to User Controls under Adjusting Your Monitor. The monitor's front configuration may vary slightly depending on the monitor model.

1. Input Signal Indicators 5. MENU button

2. TV / VIDEO button 6. Power button / Power indicator

3. PC button 7. Up-Down button / Channel button

4. EXIT button / AUTO button 8. Left-Right button / Volume button

Introduction : Rear

For detailed information concerning cable connections, refer to Connecting Cables under Setup. The monitor's rear configuration may vary slightly depending on the monitor model.

Remove the cover to connect the cables. (Pull the joining part to remove the cover.)

A Power Connection Terminal (14V DC)

This product may be used with 90 ~ 264. (Voltage is automatically adjusted by the power adaptor.)

Connect the power source plug when all cables are

connected.

B Video Connection Terminal

1 PC connection terminal (15 pin D-SUB)

2 S-Video(V1) connection terminal (S-VHS)

3 Video(V2) connection terminal (RCA)

C Audio Connection Terminal

1 Left audio(L) connection terminal (Input)

2 Right audio(R) connection terminal (Input)

3 PC sound(Stereo) connection terminal (Input)

4 Headphone connection terminal (Output)

D Antenna Connection Terminal (When TV is

connected)

E Anti-Theft Security Lock

Introduction : Remote Control

For detailed information of the Remote Control Unit functions, refer to Adjusting Your Monitor > User Controls > User Control Buttons > Remote Control buttons. The remote control's configuration may vary slightly depending on the monitor model.

The Remote control may function within a range of 0.23 to 33 feet (7cm to 10m) and 30 degrees to the left and right of the monitor's Remote Control Reception sensor.

1. Button Names

1. POWER button

2. PC button

3. MUTE button

4. AUTO / Previous channel button

5. CAPTION button

6. CHANNEL button

7. TV / VIDEO button

8. Up-Down button / Channel button

9. Left-Right button / Volume button

10. MENU button

11. EXIT button

12. +100 button

13. DISPLAY button

2. Replacing Batteries

1. To open, slide the tray handle to the right (1) and then pull it forward (2).

2. Place the battery on the tray with the right side up.

3. Push the tray back in in the arrow direction.

Setup - Connecting Your Monitor : Connecting to a Computer

Turn on your computer and monitor. If your monitor displays an image, installation is complete.

1. Connecting to a Computer

1. Connect the power cord to the DC adapter and connect the adapter jack to the DC14V power port on the back of your monitor.

2. Connect the signal cable to the video port on your computer.

3. Connect the audio cable for your monitor to the audio port on the back of your computer.

4. Connect the Audio (L) and Audio (R) terminals of a DVD, VCR or Camcorders to the monitor's L and R audio input terminals using audio cables.

5. Turn on both your computer and the monitor.

6. You may enjoy clear and quality sound from the computer sound card using the monitor speakers. (You don't need to install any separate speakers for your computer.)

Contact a local Samsung Electronics service center to buy optional items.

Setup - Connecting Your Monitor : Connecting to other devices

AV input devices like DVDs, VCRs or Camcorders as well as your computer may be connected to the monitor. For detailed information on connecting AV input devices, refer to User Controls under Adjusting Your Monitor.

1. Connecting AV Devices

The monitor has AV connection terminals to connect AV input devices like DVDs, VCRs or Camcorders. You may enjoy AV signals as long as the monitor is turned on.

1. AV input devices like DVDs, VCRs or Camcorders are connected to the S-Video (V1) or Video (V2) terminal of the monitor using the S-VHS or RCA cable.

S-VHS or RCA cable is optional.

2. Connect the Audio (L) and Audio (R) terminals of a DVD, VCR or Camcorders to the monitor's L and R audio input terminals using audio cables.

3. Select Video or S-Video that is connected to a DVD, VCR or Camcorders using the Source button on the monitor's front.

4. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted.

Setup - Connecting Your Monitor : Connecting to other devices

2. Connecting TV

You may view television programs on the monitor if it is connected to an antenna or CATV cable without installing any separate TV reception hardware or software on your computer.

1. Connect the CATV or antenna coaxial cable to the Antenna terminal on the rear of the monitor. You need to use a coaxial antenna cable.

2. Turn on the monitor.

3. Select TV using Source button among the external signal adjustment buttons.

4. Select a desired TV channel.

As this product is designed for NTSC signals only, you cannot view TV programs in countries where PAL or SECAM signals are used.

3. Connecting to a Macintosh

For older model Macintoshes, you need to adjust the resolution control DIP switch on the Macintosh

Setup - Connecting Your Monitor : Connecting to other devices

1. Connect the power cord to the DC adapter and then connect the adapter jack to the DC14V power port on the monitor. (Voltage is automatically adjusted by the power adaptor.)

2. Connect the signal cable to the D-SUB port on the Macintosh computer.

3. adapter (optional) referring to the switch configuration table shown on its rear.

4. Turn on the monitor and Macintosh.

Contact a local Samsung Electronics service center to buy optional items.

4. Connecting Headphones

You may connect your headphones to the monitor.

1. Connect your headphones to the Headphone-out port.

ROM included with

this monitor. Driver installation is slightly different from one operating system to another. Follow

Internet web site :

Setup - Installing the Monitor Driver : Automatic

When prompted by the operating system for the monitor driver, insert the CD-

the directions as appropriate for the operating system you have.

Prepare a blank disk and download the driver program file at the Internet web site shown here.

1. Windows ME

Refer to "Installing the Monitor Driver and User Manual" CD-ROM supplied with the monitor. When inserted into the computer CD drive, the CD-ROM boots up automatically. If it fails to boot up automatically, click monsetup.exe twice in the CD-ROM drive folder of Windows Explorer.

1. Insert CD into the CD-ROM driver.

2. Click "Windows ME Driver"

3. Choose your monitor model in the model list, then click the "OK" button.

http://www.samsung-monitor.com/ (Worldwide) http://www.samsungusa.com/monitor/ (USA) http://www.sec.co.kr/monitor/ (Korea) http://www.samsungmonitor.com.cn/ (China)

4. Click the "Install" button in the "Warning" window.

5. Monitor driver installation is completed.

Setup - Installing the Monitor Driver : Automatic

2. Windows XP/2000

1. Insert CD into the CD-ROM driver.

2. Click "Windows XP/2000 Driver".

3. Choose your monitor model in the model list, then click the "OK" button.

4. Click the "Install" button in the "Warning" window.

5. If you can see following Message window, then click the "Continue Anyway" button. Then click "OK" button.

This monitor driver is under certifying MS logo,and this installation don't damage your system. The certified driver will be posted on Samsung Monitor Homepage

http://www.samsung-monitor.com/

6. Monitor driver installation is completed.

+ 42 hidden pages