Samsung 1100MB User Manual

SyncMaster 1100MB

Install drivers Install programs

Notational

Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.

Prohibited Important to read and understand at all times

Do not disassemble Disconnect the plug from the outlet

Do not touch Grounding to prevent an electric shock

Power

When not used for extended periods of time, set your computer to a screen saver.

If the same image is present for long periods of time, Phosphor Burnt can be

occured, or the screen may be blurred.

Do not use a damaged or loose plug.

z This may cause an electric shock or fire.

Do not pull the plug out by the wire nor touch the plug with wet hands.

This may cause an electric shock or fire.

Use only a properly grounded plug and receptacle.

An improper ground may cause electric shock or equipment damage.

Insert the power plug firmly so that it does not come loose.

Installation

z A bad connection may cause fire.

Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage.

This may cause an electric shock or fire.

Do not connect too many extension cords or plugs to an outlet.

z This may cause fire.

Be sure to contact an authorized Service Center when installing your set in a location with heavy dust, high or low temperatures, high humidity, and chemical substances, or where it will be operated for 24 hours continuously such as an airport, train station or etc.

Failure to do so may cause serious damage to your set.

Put your monitor in a location with low humidity and a minimum of dust.

z Failure to do so may cause an electric shock or fire inside the monitor.

Do not drop the monitor when moving it.

This may cause damage to the product or human body.

Install the monitor base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf.

z Dropping the product may cause damage to the product or personal

injury.

Do not place the product on an unstable or small surface area.

Place the product on an even, stable surface, as the product may fall and cause harm to someone walking by, specifically children.

Do not place the product on the floor.

Someone, specifically children could trip over it.

Keep any flammable objects such as candles, insecticides or cigarettes away from the product.

Otherwise, this may cause a fire.

Keep any heating devices away from the power cable.

A melted coating may lead to electric shock or fire.

Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc.

z Any increase in internal temperature may cause fire.

Set down the monitor carefully.

The monitor could be damaged or broken.

Do not place the monitor face down.

z The CDT surface may be damaged.

Do not use the monitor without the monitor stand.

It could break down or cause fire due to bad ventilation.

If the monitor must be used without the supplied stand, take steps to insure proper ventilation.

When installing the product, make sure to keep it away from the wall (more than 10cm/4inch) for ventilation purposes.

z Poor ventilation may cause an increase in the internal temperature of

the product, resulting in a shortened component life and degraded performance.

Clean

When cleaning the monitor case or the surface of the CDT, wipe with a slightly moistened, soft fabric.

Do not clean Flat monitor with water. Use a water-diluted mild detergent.

(Some detergents contain significant amounts of alcohol-based solvents, which can damage (color change) or crack the monitor case. The antiglare/anti-static surface coating on the CDT may also be affected.)

Dilute the detergent (1:10 ratio) with water before using.

Do not spray water or detergent directly on the monitor.

Use the recommended detergent with a smooth cloth.

You may prevent the coated CDT from being damaged or the monitor cabinet from being dissolved, cracked or discolored.

You may buy a recommended detergent at any Service Center.

If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth.

A dirty connector may cause an electric shock or fire.

Make sure to unplug the power cord before cleaning the product.

Otherwise, this may cause electric shock or fire.

Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth.

z Do not use any chemicals such as wax, benzene, alcohol, thinners,

insecticide, air freshener, lubricant or detergent.

Contact the Service Center or Customer Center for interior cleaning once a year.

Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause malfunction or fire.

Others

Do not remove cover(or back).

This may cause an electric shock or fire.

z Refer servicing to qualified service personnel.

If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and

contact an authorized dealer or service

z This may cause an electric shock or fire.

Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle.

This may cause malfunction, an electric shock or fire.

Especially avoid operating the monitor near water or outdoors where the monitor could be exposed to snow or rain.

If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact the Service Center.

z The monitor may malfunction, causing an electric shock or fire.

Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time.

z Failure to do so may cause an electric shock or fire.

Do not try to move the monitor by pulling only the wire or the signal cable.

This may cause a breakdown, electric shock or fire due to damage to the cable.

Do not move the monitor right or left by pulling only the wire or the signal cable.

This may cause a breakdown, electric shock or fire due to damage to the cable.

Do not cover the vents on the monitor cabinet.

z Bad ventilation may cause a breakdown or fire.

Do not place water containers, chemical products or small metal objects on the monitor.

This may cause malfunction, an electric shock or fire.

If a foreign substance enters the monitor, unplug the power cord and contact the Service Center .

Do not place any heavy objects on the monitor.

This may cause an electric shock or fire.

Keep the product away from combustible chemical sprays or inflammable substances.

z This may cause an explosion or fire.

Never insert anything metallic into the monitor openings.

This may cause an electric shock, fire or injury.

Keep the monitor away from any magnetic substances.

z This may cause discoloring or distortion of the image.

Watching the monitor continuously at a too close angle may result in eyesight damage.

To ease eye strain, take at least a five-minute break after every hour of using the monitor.

Do not install the product on an unstable, uneven surface or a location prone to vibrations.

Dropping the product may cause damage to the product or personal injury. Using the product in a location prone to vibrations may shorten the lifetime of the product or may catch fire.

When moving the monitor, turn off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connected to other devices, are disconnected before moving the monitor.

z Failure to disconnect a cable may damage it and lead to fire or an

electric shock.

Place the product out of children's reach, as they could damage it by hanging onto it.

A falling product could cause physical damage even death.

When not using the product for an extended time period, keep the product unplugged

Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, leading to electric shock or fire.

Do not place children's favorite objects (or anything else that may be tempting) on the product.

z Children may try to climb on the product to retrieve an object. The

product could fall, causing physical damage or even death.

Unpacking

Please make sure the following items are included with your monitor.

If an

items are missing, contact your dealer.

Monitor and Stand

(Some models include a stand attached.)

Manual

Warranty Card

User's Guide,

(Not available in all

(

Cable

Quick Setup Guide

locations)

Monitor Driver,

Natural Color software,

icTune™ software

Power Cord

Stand

Front

D-sub Cable

BNC Cable

Sold separatel

1. MagicBright™ button []

MagicBright™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching.

2. Exit button [ ]

3. Adjust buttons [ ] / [ ] / [ ]

4. Menu button [ ]

5. Power indicator

6. Power button [ ]

See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.

Rear

Use this button for Exit the active menu or the OSD.

These buttons allow you to highlight and adjust items in the menu. Adjust Brightness and Contrast.

Use this button for open the OSD and activate a highlighted menu item.

This light glows green during normal operation, and blinks green once as the monitor saves your adjustments.

Use this button for turn the monitor on and off.

(The configuration at the back of the monitor may vary from product to product.)

1. Power port

2. Signal port

3. BNC Connectors

See Connecting the Monitor for further information regarding cable connections.

Connect the power cord for your monitor to the power port on the back of the monitor.

Connect the signal cable to the 15-pin, D-sub connector on the back of your computer.

Connect the signal cable to the BNC signal port on the back of your monitor.

1. Tilt/Swivel Base

Bottom

You can separate the base from the monitor.

Connecting the Monitor

Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet.

2-1.

Connecting to a computer Connect the signal cable to the 15-pin, D-sub connector on the back of your computer.

2-2.

Connecting to a new Macintosh Connect the monitor to the Macintosh computer using the D-SUB connection cable.

2-3.

Connecting to an old Macintosh Connect your monitor to the Macintosh using the adapter for Macintosh (sold separately).

When you use a BNC connector. Connect the BNC cable(sold separately) to the BNC signal port on the back of your monitor/computer.

Turn on your computer and monitor. If your monitor displays an image, installation is complete.

Base Installation

Tilt/Swivel Base | Attaching and Removing the Base

Tilt/Swivel Base

With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable viewin

angle.

Attaching and Removing the Base

Attachin

the Base

1. Place the monitor upside-down on a flat work surface.

2. Align the tabs on the base with the corresponding slots on the bottom of the monitor.

3. Press the base onto the monitor until the tabs are fully engaged in the slots.

4. Push the base toward the front of the monitor until the release latch clicks into the locked position. * Do not bend the snap.

Removin

the Base

5. Squeeze and pull up on the release latch on the base.

6. Push the base toward the back of the monitor and lift up to remove the base.

The base will align with the monitor slots in only one position.

Installing the Monitor Driver (Automatic)

When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have.

Prepare a blank disk and download the driver program file at the Internet web site shown here.

Internet web site : http://www.samsung.com/ (Worldwide)

http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China)

Windows ME

1. Insert CD into the CD-ROM drive.

2. Click

"Windows ME Driver"

3. Choose your monitor model in the model list, then click the

4. Click the

"Install"

button in the

"Warning"

window.

"OK"

button.

5. Monitor driver installation is completed.

Windows XP/2000

1. Insert CD into the CD-ROM drive.

2. Click

"Windows XP/2000 Driver"

3. Choose your monitor model in the model list, then click the

"OK"

button.

4. If you can see following message window, then click the Then click

"OK"

button.

This monitor driver is under certified MS logo and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage.

http://www.samsung.com/.

5. Monitor driver installation is completed.

Installing the Monitor Driver (Manual)

"Continue Anyway"

button.

Windows XP | Windows 2000 | Windows Me | Windows NT | Linux

Prepare a blank disk and download the driver program file at the Internet web site shown here.

Internet web site : http://www.samsung.com/ (Worldwide)

http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China)

Microsoft® Windows® XP Operating System

1. Insert CD into the CD-ROM driver.

2. Click "

Start

" —> "

Control Panel

" then click the "

Appearance and Themes

" icon.

3. Click "

Display

4. Click the "

" icon and choose the "

Properties

" button on the "

Settings

" tab then click "

Advanced..

Monitor

" tab and select "

Driver

" tab.

5. Click "

6. Select "

Update Driver..

" and select "

Don't search ,I will..

Install from a list or..

" then click "

" button.

" and then click "

Have disk

7. Click the "

Browse

model list and click the "

" button then choose A:(D:\Driver) and choose your monitor model in the

" button.

8. If you can see following message window, then click the " click "OK" button.

Continue Anyway

" button. Then

This monitor driver is under certified MS logo and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage.

htt

://www.samsung.com/.

9. Click the "

" button, then click "OK" button continually.

(

play

10. Monitor driver installation is completed.

Microsoft

Windows® 2000 Operating System

When you can see "Digital Signature Not Found" on your monitor, follow these steps.

1. Choose "OK" button on the "

2. Click the "

3. Choose A:

Browse

" button on the "

D:\Driver) then click the "Open" button and then click "OK" button.

Insert disk

" window.

File Needed

" window.

How to install

1. Click "

2. Double click the "

3. Choose the "

4. Choose "

Start

Monitor

" , "

Setting

Settings

" , "

Control Panel

Display

" Icon.

" tab and then click "

Advanced..

Case1:If the "Properties" button is inactive, it means your monitor is properly configured.

Please stop installation

Case2:If the "Properties" button is active, click the "Properties" button then follow next steps

continually.

5. Click "

6. Choose "

specific driver

7. Click the "

8. Click the "

9. Choose your monitor model and click the "

10. Click the "

If you can see the " And click the "

" and then click on "

Driver

Update Driver..

" then click on the "Next" button.

Display a list of the known drivers for this device so that I can choose a

" then click "

Browse Open

Finish

" button then choose A:(D:\Driver).

" button, then click "OK" button.

" button then the "

Digital Signature Not Found

" button then the "

Finish

" and then click "

" button.

Have disk

" button then click "

" window then click the "

" button.

Yes

Microsoft

1. Click "

2. Double click "

3. Select the "

4. Select the "

5. Click the "

6. Choose "

7. Choose "

8. Click the "

Windows® Millennium Operating System

" , "

Start

Setting

Display Settings Monitor

Change

Specify the location of the driver

" , "

Control Panel

" icon.

" tab and click "

" tab.

" button in the "

Advanced Properties

Monitor Type

" area.

Display a list of all the driver in a specific location..

Have Disk

" button

" button.

" then click "

9. Specify A:\(D:\driver) then click "OK" button.

10. Select "

Show all devices

" and choose the monitor that corresponds to the one you

connected to your computer and click "OK".

11. Continue choosing " dialo

ue box.

" button and "OK" button until you close the Display Properties

Microsoft

1. Click

Windows® NT Operating System

Start, Settings, Control Panel

, and then double-click

Display

icon.

2. In Display Registration Information window, click Settings Tab and then click .

Modes

3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency)

and then click OK.

4. Click

button if you see the screen working normally after clicking

Apply

Test

not normal, change to a different mode (lower mode of resolution, colors or frequency).

"button.

" button.

All Display

. If the screen is

If there is no Mode at

All Dis

Modes

, select the level of resolution and vertical

+ 43 hidden pages