Samsung 1080P7 User Manual

DVD Player

DVD-1080P7

www.samsung.com/sg

PRECAUTIONS

1. Setting up

- Refer to the identification label located on the rear of your player for its proper operating voltage.

- Install your player in a cabinet with adequate ventilation holes. (7~10cm) Do not block ventilation holes on any of the components for air circulation.

- Do not push the disc tray in by hand.

- Do not stack components.

- Be sure to turn all components off before moving the player.

- Before connecting other components to this player, be sure to turn them off.

- Be sure to remove the disc and turn off the player after use, especially if you are not going to use it for a long time.

- The main plug is used as a disconnect device and shall stay readily operable at any time.

2. For your safety

- This product utilizes a laser. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

- Do not open covers and do not repair yourself. Refer servicing to qualified personal.

3. Caution

- Your player is not intended for industrial use but for domestic purposes. Use of this product is for personal use only.

- Apparatus shall not be exposed to dripping or splashing and no object filled with liquids, such as vases, shall be placed on the apparatus.

- Exterior influences such as lightning and static electricity can affect normal operation of this player. If this occurs, turn the player off and on again with the POWER button, or disconnect and then reconnect the AC power cord to the AC power outlet. The player will operate normally.

- When condensation forms inside the player due to sharp changes in temperature, the player may not operate correctly. If this occurs, leave the player at room temperature until the inside of the player becomes dry and operational.

4. Disc

- Do not clean disc using record-cleaning sprays, benzene, thinner, or other volatile solvents that may cause damage to the disc surface.

- Do not touch the disc’s signal surface. Hold by the edges or by one edge and the hole in the center.

- Wipe the dirt away gently; never wipe a cloth back and forth over the disc.

5. Environmental info

- The battery used in this product contains chemicals that are harmful to the environ ment.

- So, dispose of batteries in the proper man ner, according to federal, state, and local regulations.

The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for commercial use. The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit or process conforming to ISO/OUR 11172-3 or ISO/OUR 13818-3 used or sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode audio files conforming to the ISO/OUR 11172-3 or ISO/OUR 13818-3. No rights are granted under this license for product features or functions that do not conform to the ISO/OUR 11172-3 or ISO/OUR 13818-3.

CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER THAN SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

BEFORE

ARTT

YOU

ABLE OF

TTABLE OF

CONTENTS

Accessories

Remote Control

User’s Manual

Install Batteries in the Remote control

1. Open the battery cover on the back of the remote control.

2. Insert two AAA batteries. Make sure that the polarities (+ and -) are aligned correctly.

3. Replace the battery cover.

If remote control doesn’t operate properly:

- Check the polarity + - of the batteries (Dry-Cell)

- Check if the batteries are drained.

- Check if remote control sensor is blocked by

obstacles.

- Check if there is any fluorescent lighting nearby.

Batteries for Remote

Control (AAA Size)

Video/Audio

Cable

HDMI Cable

Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Setup

General Features . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Disc Type and Characteristics . . . . . . . . . . . . . . . . 5

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Tour of the Remote Control . . . . . . . . . . . . . . . . . . 8

Connections

Choosing a Connection . . . . . . . . . . . . . . . . . . . . . 9

Basic Functions

Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Using the Search and Skip Functions . . . . . . . . . 17

Using the Display Function . . . . . . . . . . . . . . . . . 17

Using the Disc and Title Menu . . . . . . . . . . . . . . 18

Using the Function Menu . . . . . . . . . . . . . . . . . . 18

Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Advanced Functions

Adjusting the Aspect Ratio (EZ View) . . . . . . . . . 19

Selecting the Audio Language . . . . . . . . . . . . . . . 20

Selecting the Subtitle Language. . . . . . . . . . . . . . 20

Changing the Camera Angle . . . . . . . . . . . . . . . . 21

Using the Instant Replay/Skip Function . . . . . . . . 21

Using the Bookmark Function . . . . . . . . . . . . . . . 21

Using the Zoom Function . . . . . . . . . . . . . . . . . . . 22

Clips Menu for MP3/WMA/JPEG/MPEG4/

CD Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . . 22

MP3/WMA/CD Audio Playback. . . . . . . . . . . . . . . 23

MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . . . . 23

Picture CD Playback. . . . . . . . . . . . . . . . . . . . . . . 25

Changing Setup Menu

Using the Setup Menu . . . . . . . . . . . . . . . . . . . . . 26

Setting Up the Language Features . . . . . . . . . . . 26

Setting Up the Audio Options . . . . . . . . . . . . . . . . 27

Setting Up the Display Options . . . . . . . . . . . . . . 28

Setting Up the Parental Control . . . . . . . . . . . . . . 30

Setting Up the Anynet+(HDMI-CEC) . . . . . . . . . . 31

Reference

Firmware upgrade . . . . . . . . . . . . . . . . . . . . . . . . 32

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

English

SETUP

General Features

Excellent Sound

Dolby Digital, a technology developed by Dolby Laboratories, provides crystal clear sound reproduction.

Screen

Both regular and widescreen(16:9) pictures can be viewed.

Slow Motion

An important scene can be viewed in slow motion.

1080p Playback

This player upconverts regular DVDs for playback on 1080p TVs.

Parental Control (DVD)

The parental control allows users to set the level necessary to prohibit children from viewing harmful movies such as those with violence, adult subject matter, etc.

Various On-Screen Menu Functions

You can select various languages (Audio/Subtitle) and screen angles while enjoying movies.

Progressive Scan

Progressive scanning creates an improved picture with double the scan lines of a conventional interlaced picture.

EZ VIEW (DVD)

Easy View enables picture adjustment to match your TV's screen size (16:9 or 4:3).

Digital Photo Viewer (JPEG)

You can view Digital Photos on your TV.

Repeat

You can repeat a song or movie simply by pressing the REPEAT button.

MP3/WMA

This unit can play discs created from MP3/WMA files.

Instant Replay (DVD)

This function is used to replay the previous 10 seconds of a movie from the current position.

Instant Skip (DVD)

This function skips playback ahead 10 seconds

MPEG4

This unit can play MPEG4 formats within an avi file.

HDMI (High Definition Multimedia Interface)

HDMI reduces picture noise by allowing a pure digital video/audio signal path from the player to your TV.

Note

- Discs which cannot be played with this player.

• DVD-ROM • DVD-RAM

• CD-ROM • CDV

• CDI • CVD

• CDGs play audio only, not graphics.

- Ability to play back may depend on recording conditions.

• DVD-R, +R

• CD-RW

• DVD+RW, -RW (V mode)

- The unit may not play certain CD-R, CD-RW and DVD-R due to the disc type or recording conditions.

COPY PROTECTION

Many DVD discs are encoded with copy protection. Because of this, you should only connect your DVD player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copyprotected DVD discs.

This product incorporates copyright protection technology that is protected by methods claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be auzthorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

PROGRESSIVE SCAN OUTPUTS (525p, 720p, 1080p)

“CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE, IN CASE OF 525, 720 OR 1080 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS REGARDING YOUR TV SET COMPATIBILITY WITH THIS MODEL 525p, 720p AND 1080p DVD PLAYER, PLEASE CONTACT SAMSUNG'S CUSTOMER SERVICE CENTER.”

Disc Type and Characteristics

This DVD player is capable of playing the following types of discs with the corresponding logos:

Disc Types (Logos)

DVD

VIDEO-CD

AUDIO-CD

Disc Markings

Play Region Number

PAL

STEREO

DIGITAL

SOUND

PAL broadcast system in U.K, France, Germany, etc.

Dolby Digital disc

Stereo disc

Digital Audio disc

Recording Types Disc Size Max. Playing Time Characteristics

- DVD contains excellent sound and video due to Dolby Digital and MPEG2 system.

- Various screen and audio functions can be easily selected through the onscreen menu.

- Video with CD sound, VHS quality & MPEG-1 compression technology.

- CD is recorded as a Digital Signal with better audio quality, less distortion and less deterioration of audio quality over time.

Audio

Video

Audio

Video

Audio

12 Cm

8 Cm

12 Cm

8 Cm

12 Cm

8 Cm

Single-sided 240 min.

Double-sided 480 min.

Single-sided 80 min.

Double-sided 160 min.

74 min.

20 min.

74 min.

20 min.

Region Number

Both the DVD player and the discs are coded by region. These regional codes must match in order for the disc to play. If the codes do not match, the disc will not play.

The Region Number for this player is described on the rear panel of the player.

English

DTS disc

MP3 disc

You must only insert one DVD disc at a time. Inserting two or more discs will not allow to play them back and it may cause damage to the DVD player.

DivX Certification

DivX, DivX Certified, and associated logos are trademarks of DivXNetworks, Inc and are used under license

OPEN/CLOSE

Description

Front Panel Controls

1. STANDBY/ON ( )

When STANDBY/ON is pressed on, the indicator goes out and the player is turned on.

2. STANDBY Indicator

When the unit is first plugged in, the indicator lights.

3. DISC TRAY

Place the disc here.

4. OPEN/CLOSE ( )

Press to open and close the disc tray.

5. DISPLAY

Operation indicators are displayed here.

6. VIDEO SEL.

Press to change Video output mode.

7. STOP ( )

Stops disc play.

8. SKIP ( ) / SEARCH

Use to forward skip a scene or music.

9. SKIP ( ) / SEARCH

Use to reverse skip a scene or music.

10. PLAY/PAUSE ( )

Begin or pause disc play.

Front Panel Display

Total playing time/Displays various messages concerning operations such as PLAY, STOP, LOAD ...

nodSC: No disc loaded. OPEn: The disc tray is open. LOAd: Player is loading disc information.

Rear Panel

1. DIGITAL AUDIO OUT JACKS

- Use either an optical or coaxial digital cable to connect to a compatible Dolby Digital receiver.

- Use either an optical or coaxial digital cable to connect to an A/V Amplifier that contains a Dolby Digital, MPEG2 or DTS decoder.

2. COMPONENT VIDEO OUT JACKS

- Use these jacks if you have a TV with Component Video in jacks. These jacks provide P

- If P-SCAN Video Output is selected in Setup Menu, progressive scan mode will work.

- If I-SCAN Video Output is selected in Setup Menu, interlaced scan mode will work.

3. AUDIO OUT JACKS

- Connect to the Audio input jacks of your television or audio/video receiver.

4. VIDEO OUT JACK

- Use a video cable to connect to the Video input jack on your television.

- The Video Output in Setup Menu must be set to S-Video.

, PBand Y video.

5. S-VIDEO OUT JACK

- Use the S-Video cable to connect this jack to the SVideo jack on your television for higher picture quality.

- The Video Output in Setup Menu must be set to S-Video.

6. HDMI OUT JACK

- Use the HDMI cable to connect this jack to the HDMI jack on your television for the best quality picture.

- If an HDMI cable is connected to an HDMI-compatible TV, HDMI will be output automatically within 10 seconds.

English

Note

- Consult your TV User’s Manual to find out if your TV supports Progressive Scan (P-SCAN).

If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s menu system.

- The HDMI output of this unit can be connected to a DVI jack on a TV or other device using a conver-

sion adapter. In this case, it is necessary to use a TV or display with an HDCP-compatible DVI input.

- There may be no image output if the DVD player is connected to a TV or display that is not compatible

with the above format.

- Refer to the TV's instruction manual for detailed information regarding the HDMI terminal.

- See pages 28 ~ 29 to get more information on how to use the setup menu.

Tour of the Remote Control

1 2

6 7

8 9

15 16

1. VIDEO SEL. Button

Change Video output mode.

2. HDMI SEL. Button

HDMI Output resolution setup.

3. DVD POWER Button

Turns the power on or off.

4. NUMBER Buttons

5. BOOKMARK Buttons

6. SEARCH Buttons (

Allow you to search forward/backward through a disc.

)

7. INSTANT REPLAY Button

This function is used to replay the previous 10 seconds

17 18

19 20

25 26

29 30

of a movie from the current position.

8. SKIP Buttons (

Use to skip the title, chapter or track.

9. STOP Button ( )

10. TV VOL (+, -) Buttons

Control volume

11. MENU Button

Brings up the DVD player’s menu.

12. ENTER/

This button functions as a toggle switch.

13. EZ VIEW Button

The aspect ratio of a picture can easily be adjusted according to the screen size of your TV (16:9 or 4:3).

14. DISC MENU Button

Brings up the Disc menu.

15. SUBTITLE Button

16. AUDIO Button

Use this button to access various audio functions on a disc.

17. REPEAT A-B Button

Allows you to repeat play A-B on a disc.

18. REPEAT Button

Allows you to repeat play a title, chapter, track, or disc.

19. TV POWER Button

Turn the TV’s power on or off.

20. OPEN/CLOSE ( ) Button

To open and close the disc tray.

21. STEP Button

Advances play one frame at a time.

22. INSTANT SKIP Button

This function skips playback ahead 10 seconds.

23. PLAY/PAUSE Button ( )

Begin/Pause disc play.

24. TV CH ( , ) buttons

Channel selection.

25. TV/VIDEO Button

Press to display all of the available video sources (i,e., TV, Cable, Video).

26. RETURN Button

Returns to a previous menu.

27. EXIT Button

Exit the on-screen menu.

28. CANCEL Button

Use to remove menus or status displays from the screen.

29. ZOOM Button

Enlarge DVD Picture

30. INFO Button

Displays the current disc mode.

/,¦¦/

Buttons

)

CONNECTIONS

Choosing a Connection

The following shows examples of connections commonly used to connect the DVD player with a TV and other components.

Before Connecting the DVD Player

- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.

- Refer to the user’s manual of the additional components you are connecting for more information on those particular components.

Connection to a TV (For Video)

Using video/audio cables, connect the VIDEO (yellow)/AUDIO (red and white) OUT terminals on the rear of the DVD player to the VIDEO (yellow)/AUDIO (red and white) IN terminals of TV.

Turn on the DVD player and TV.

RED

Audio Cable

WHITE

YELLOW

Video Cable

YELLOW

English

Press the input selector on your TV remote control until the Video signal from the DVD player appears on the TV screen.

Note

- Noise may be generated if the audio cable is too close to the power cable.

- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 14 to 15)

- The number and position of terminals can vary depending on your TV set. Please refer to the user's

manual of the TV.

- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of the DVD player.

- If you press the VIDEO SEL. button when DVD Player is in stop mode or no disc is inserted, the Video Output mode changes in the following sequence: (COMPOSITE/S-Video ➝ I-SCAN ➝ P-SCAN)

- If you set the HDMI output resolution, S-Video output cannot be used.

Connection to a TV (S-Video)

- Connecting to your TV using an S-Video cable.

- You will enjoy high quality images. S-Video separates the picture element into black and white(Y) and color(C) signals to present clearer images than regular video input mode. (Audio signals aredelivered through the audio output.)

Using an S-Video cable (not included), connect the SVIDEO OUT terminal on the rear of the DVD player to the S-VIDEO IN terminal of TV.

Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of TV. Turn on the

DVD player and TV.

RED

Press the input selector on your TV remote control until the S-Video signal from the DVD player appears on your TV screen.

WHITE

Audio Cable

WHITE

RED

S-Video Cable (not included)

Set the Video Output to S-Video in the Display Setup menu. (See pages 28 to 29) You can use the VIDEO SEL. button to change the Video Output mode. (See page 9)

Note

- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 14 to 15)

- The number and position of terminals can vary depending on the TV set. Please refer to the user's manual of the TV.

- Please do not connect S-Video and Component Video (Y, Pb, Pr) output simultaneously, as they may interfere and degrade both video output quality.

- If you set the HDMI output resolution, S-Video output cannot be used.

Connection to a TV (Interlace)

- Connecting to your TV using Component video cables.

- You will enjoy high quality and accurate color reproduction images. Component video separates the picture element into black and white(Y), blue(PB), red(PR) signals to present clear and clean images. (Audio signals are delivered through the audio output.)

Using component video cables (not included), connect the COMPONENT VIDEO OUT terminal on the rear of the DVD player to the COMPONENT IN terminal of TV.

English

Using the audio cables, connect the AUDIO (red and

RED

GREEN

BLUE

white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of TV. Turn on the

DVD player and TV.

Press the input selector on your TV remote control until the Component signal from the DVD player appears on the TV screen.

RED

Audio Cable

WHITE

RED WHITE

BLUE

RED

GREEN

Component cable (not included)

Set the Video Output to I-SCAN in the Display Setup menu. (See pages 28 to 29) You can use the VIDEO SEL. button to change the Video Output mode. (See page 9)

Note

- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 14 to 15)

- The component terminal of TV can be marked by “R-Y, B-Y, Y” or “Cr, Cb, Y” instead of “P depending on the manufacturer. The number and position of terminals can vary depending on the TV set. Please refer to the user's manual of the TV.

- If you set the HDMI output resolution, S-Video output cannot be used.

, PB, Y”

+ 25 hidden pages