Samson Pfeiffer BR Series, Pfeiffer BR 10e Series, Pfeiffer BR 10a Series Operating Instructions Manual
Specifications subject without notice
Edition:
EN
T R A N S L A T I O N
Declaration of Conformity as per Directive 2014/68/EU
The manufacturer
Pfeiffer Chemie-Armaturenbau GmbH, 47906 Kempen, Germany
PTFE-lined shut-off butterfly valves
•
• with lever for 90° operation
1. The valves are pressure accessories within the meaning of the Pressure Equipment Directive 2014/68/EU
(See section 2.3 for butterfly valves intended for dead-end service)
Applied standards:
EN 593
AD2000 Regulations
Product standard for butterfly valves
Regulations for pressurized valve body parts
Type designation and technical features:
TB10a
TB10e>
Applied conformity assessment procedure:
Conforming to Annex III of the Pressure Equipment Directive 2014/68/EU, Module H
Name of notified body:
Identification number of the notified body:
TÜV Rheinland Service GmbH
Germany
Kempen, 28. November 2017
Marcus Miertz, Chief Executive Officer
Stefan Czayka, IMS Representative
declares that:
and conform with the requirements of this Directive,
2. They may only be operated observing the operating instru cti o ns <BA10a-01> delivered together with the
valve.
Pfeiffer data sheets <
NOTE: This Manufacturer’s Declaration applies to all valve types listed in this catalogue.
BR 10a and BR 10e, with PTFE liner and shaft packing
with worm gear and handewheel
and
Am Grauen Stein
51101 Köln
These Declarations become invalid when modifications are made to the shut-off butterfly valves and/or assemblies that affect
the technical data of the shut-off butterfly valve or the <Intended use> described in section 1 of the operating instructions, and
considerably change the valve or an assembly delivered with it.
1 of 9
November 2017 Operating instructions BA 10a-02_
0035
Specifications subject without notice
Edition:
EN
Operating instructions
Shut-off butterfly valve with PTFE lining
manually operated
Contents
0. Introduction 3
1. Intended use 3
2. Safety instructions 3
2.1 General safety instructions 3
2.2 Safety instructions for the operator 3
2.3 Particular hazards 4
2.4 Designation of the shut-off butterfly valve 5
3. Transport and storage 5
4. Installation in the pipeline 6
4.1 General 6
4.2 Installation instructions 6
5. Pressure check in pipeline section 7
6. Standard operation and maintenance 8
7. Troubleshooting 8
8. Further information 9
2 of 9
November 2017 Operating instructions BA 10a-02_
Specifications subject without notice
Edition
EN
Note
Do not operate a shut-off butte r fly valve when its permissible pressure/temperature rating is not sized for the
installed in the pipeline.
Pfeiffer valves do not have their own potential ignition source according to the risk assessment in the rare incident
Relating to this directive, CE marking is not permissible. The integration of valves into the equipotential bonding of
DIN EN 13463-1.
0. Introduction
These instructions are designed to assist the user during installation, operation and maintenance of shut-off butterfly valves with
PTFE lining from the BR10a and BR10e.
The WARNING and CAUTION notes must be strictly adhered to. Otherwise this may lead to personal injury and
equipment damage and the manufacturer’s warranty may become void.
Please contact the manufacturer if you have any queries, see section 8 for contact address.
1. Intended use
After installing the valve in the pipeline and connecting the actuator to the control equipment, these shut-off butterfly valves are
designed exclusively for shutting off or controlling media (often corrosive) within the permissible pressure and temperature
ranges.
The permissible pressure and temperature ranges for these shut-off butterfly valves are specified in the data sheets <TB10a or
TB10e>.
operating conditions specified in the data sheets <TB10a or TB10e>.
Danger
Observation of conformity with the Directive 2014/34/EU:
Failure to follow these safety precautions may result in personal injury and can damage equipment
of an operating fault in accordance with DIN EN 13463-1 and therefore do not fall within the scope of the Directive
2014/34/EU.
a plant applies to all metallic parts in hazardous areas regardles s of the directiv e.
Note
Valves with plastic lining (PFA, PTFE) in applications with chargeable media have to be lined with conductive
plastic lining with a surface resistance less than 1 Gigaohm (10
9
Ohm) in accordance with paragraph 6.7.5a of
Refer to the limitations in the above mentioned data sheets if the shut-off butterfly valve is intended for throttling services.
Parts subject to wear are not covered by the warranty.
Observance of section 2 <Safety instructions> is presumed for the Intended use.
2. Safety instructions
2.1 General safety instructions
For shut-off butterfly valves, the same safety regulations apply as for the pipelines in which they are installed. These instructions
only specify those safety instructions which need to be additionally observed concerning shut-off butterfly valves.
2.2 Safety instructions for the operator
The manufacturer does not assume any responsibility. Therefore, on using the shut-off butterfly valve, make sure the following
instructions are observed:
The valve is to be used only for its intended use as described in section 1.
3 of 9
: November 2017 Operating instructions BA 10a-02_
Loading...